HoistFitness | V-3-PRESSARM | Owner Manual | HoistFitness V-3-PRESSARM Owner Manual

HoistFitness V-3-PRESSARM Owner Manual
OWNER'S MANUAL
V3-PRESS ARM
Note: Both Serial Number and Model Number are Required when Ordering Parts
RECORD SERIAL NUMBER HERE
CATALOG NUMBER
0907 - 002
Customer Service
(800) 548-5438
(858) 578-7676
Fax
(858) 578-9558
OWNER'S MANUAL
CONTENTS
INSTRUCTIONS ..................................................................... 02
FRAME ASSEMBLY .............................................................. 04
PRE-ASSEMBLY.................................................................... 14
DECAL PLACEMENT............................................................. 15
DECAL REFERENCE............................................................. 16
PART LIST............................................................................... 17
ABBREVIATIONS................................................................... 18
BOLT SIZING CHART............................................................ 19
WASHER SIZING CHART...................................................... 21
MAINTENANCE SCHEDULE................................................. 23
GENERAL MAINTENANCE INFORMATION........................ 24
WEIGHT TRAINING TIPS....................................................... 25
EXERCISE LOG...................................................................... 27
LIMITED WARRANTY............................................................ 28
PAGE 01
V3-PRESS ARM ASSEMBLY
OWNER'S MANUAL
INSTRUCTIONS
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.
HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted for, continue on.
TOOLS REQUIRED
Ratchet Wrench
1/2", 9/16" and 3/4" Sockets
Adjustable Wrench
Rubber Mallet
Tape Measure
Level
Hex Key Wrench Set
2 People Required For Assembly
V3-PRESS ARM ASSEMBLY
PAGE 02
OWNER'S MANUAL
***THIS PAGE WAS INTENTIONALLY LEFT BLANK***
PAGE 03
V3-PRESS ARM ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
V3-PRESS ARM ASSEMBLY
PAGE 04
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
ASSEMBLY OF PRESS
ARM HANGER SHOWN IN
V BASE MANUAL.
*
V BASE UNIT (SELECT
OR ELITE VERSION)
5*
17
PAGE 05
V3-PRESS ARM ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
4
5
17
V3-PRESS ARM ASSEMBLY
PAGE 06
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
26
7
4
PAGE 07
V3-PRESS ARM ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
28
18
5
V3-PRESS ARM ASSEMBLY
PAGE 08
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
5
16
4
PAGE 09
V3-PRESS ARM ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE (30) THEN
LOOSEN NUT JUST ENOUGH FOR (1)
TO PIVOT FREELY.
- REPEAT ASSEMBLY FOR OPPOSITE SIDE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
30
24
4
24
32
1
V3-PRESS ARM ASSEMBLY
PAGE 10
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- REPEAT ASSEMBLY FOR OPPOSITE SIDE.
4
23
29
31
23
19
PAGE 11
V3-PRESS ARM ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE (30) THEN
LOOSEN NUT JUST ENOUGH FOR (2) & (3)
TO PIVOT FREELY.
- REPEAT ASSEMBLY FOR OPPOSITE SIDE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
30
4
3
24
19
24
2
32
V3-PRESS ARM ASSEMBLY
PAGE 12
OWNER'S MANUAL
***THIS PAGE WAS INTENTIONALLY LEFT BLANK***
PAGE 13
V3-PRESS ARM ASSEMBLY
OWNER'S MANUAL
PRE-ASSEMBLY
12
12
6
6
6
36
15
36
6
15
2
8
11
3
5
8
8
21
9
9
8
1
4
8
8
1
6
8
6
10
10
14
6
20
14
6
13
13
20
22
22
25
27
25
27
V3-PRESS ARM ASSEMBLY
PAGE 14
OWNER'S MANUAL
DECAL PLACEMENT
35
33
5
34
PAGE 15
V3-PRESS ARM ASSEMBLY
OWNER'S MANUAL
DECAL REFERENCE
021-0003307
021-0003669
V3-PRESS ARM ASSEMBLY
SERIAL # DECAL
PAGE 16
OWNER'S MANUAL
PART LIST
NOTE: SOME OF THESE PARTS MAY COME PRE-INSTALLED
ITEM NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
PAGE 17
PART NUMBER
026-01X1411
026-01X3211
026-01X3212
026-01X4051
026-01X5083
011-0111008
014-0019005-1
014-0101002
014-0101005
016-0101017
019-0001001
019-0002050
026-01M0932
026-01M0933
026-01M0936
026-01M2550
026-01M2267
026-01P6136
026-01PL198
026-01PL0235-15
026-01PL0382
013-0002003
013-0402007
013-0102003
013-0102023
011-0007097
011-0101025
011-0002049
011-0107020
011-0407024
012-0104008
012-0304011
021-0003307
021-0003669
SERIAL # DECAL
016-0201007
DESCRIPTION
U-JOINT ASSEMBLY
LEFT ARTICULATING HANDLE ASSEMBLY
RIGHT ARTICULATING HANDLE ASSEMBLY
PRESS ARM ASSEMBLY
PRESS ARM HANGER ASSEMBLY
SET SCREW: 1/4"-28 X .25" LG. (WZ)
T SPLIT COLLAR THREADED 1.00" I.D. X 20mm
BUSHING: OILITE FLANGED Ø.75" O.D X Ø.50" I.D X .38" LG.
BUSHING: OILITE FLANGED Ø1.38" O.D. X Ø1.00" I.D. X .81" LG.
END CAP 2.00" X .120" WALL (GRAY)
PLUG BUMPER
GRIP CLOSED END 1.00" X 17.50" LG.
END CAP: ALUMINIUM 1.25" ID
ALUMINUM RING: 1.25" ID
1.00" I.D.
ALUMINIUM RING:
PULL PIN CAP
SHAFT: 1.00" X 9.44"
FIXED PLATE
HANDLE CLIP
GRIP OPEN END 1.25" X 11.00 LG.
DUAL STEM PLUG BUMPER - BLACK
1/4" X 16mm SAE FLAT WASHER (WZ)
3/8" X 22mm FLAT WASHER (WZ)
1/2" X 27mm SAE FLAT WASHER (WZ)
1/4" INTERNAL LOCK WASHER
1/4"-20UNC X .75" SHCS (BZ)
1/4"-20UNC X 1.00" BHCB (WZ)
3/8"-16UNC X .75" FHCS (WZ) W/NYLON PATCH
3/8"-16UNC X 3.25" HHB (WZ)
1/2"-13UNC X 2.75" HHB (WZ)
3/8"-16 UNC THIN NYLOCK NUT (WZ)
1/2"-13 UNC THIN NYLOCK NUT (WZ)
DECAL DO NOT HANG (LAT AREA) 1.63" X 2.50"
DECAL: V3 BADGE
DECAL HOIST SERIAL # 1.63" X 2.63"
END CAP 1.00" (BLACK)
QTY.
2
1
1
1
1
8
4
8
2
2
2
2
2
2
2
1
1
1
2
2
1
2
4
8
2
8
2
2
2
4
2
4
1
1
1
2
V3-PRESS ARM ASSEMBLY
OWNER'S MANUAL
ABBREVIATIONS
BZ = Black Zinc
WZ = White Zinc
HHB = Hex Head Bolt
FHCS = Flat Head Cap Screw
BHCS = Button Head Cap Screw
SHCS = Socket Head Cap Screw
SHSS = Socket Head Shoulder Screw
V3-PRESS ARM ASSEMBLY
PAGE 18
OWNER'S MANUAL
BOLT SIZING CHART
1 3/4"
5/16" HHB
1 1/4"
2 3/4"
2 1/4"
4 1/4"
3 1/4"
2 1/2"
1 1/2"
1"
5 1/4"
4 1/2"
3 1/2"
4"
3"
2"
4 3/4"
3 3/4"
5 1/2"
5"
0"
2 3/4"
1 3/4"
3/8" HHB
2 1/4"
1 1/4"
0"
1"
2"
1"
1/2" SHSS
1 1/4"
1 1/2"
0"
PAGE 19
1"
4"
5"
3 1/4"
2 1/2"
2"
5 1/2"
3 3/4"
2 3/4"
2 1/4"
5 1/4"
4 1/2"
3 1/2"
3"
1 3/4"
4 3/4"
4 1/4"
3 1/4"
5 1/2"
5"
3 3/4"
2 1/2"
1 1/2"
0"
4"
2 3/4"
2 1/4"
1 1/4"
5 1/4"
4 1/2"
3 1/2"
3"
2"
1 3/4"
1/2" HHB
4 1/4"
3 1/4"
2 1/2"
1 1/2"
4 3/4"
3 3/4"
3 1/2"
3"
4"
V3-PRESS ARM ASSEMBLY
OWNER'S MANUAL
BOLT SIZING CHART
(CONTINUED)
3/8" FHCS
3/4"
1 3/4"
1 1/4"
2 3/4"
2 1/4"
1 1/2"
1"
0"
2 1/2"
3"
2"
3/8" BHCS
3/8" SHCS
3/4"
1"
3/4"
0"
0"
1/2" FHCS
1/4" HHB
3/4"
3/4"
1 1/4"
1 1/2"
0"
1"
0"
V3-PRESS ARM ASSEMBLY
1"
PAGE 20
OWNER'S MANUAL
WASHER SIZING CHART
013-0002003
1/4"
FLAT WASHER
SMALL, SAE, 13mm
013-0102028
3/8"
CURVED WASHER
013-0102004
5/16"
FLAT WASHER
LARGE, USS, 22mm
013-0002004
3/8"
FLAT WASHER
SMALL, SAE, 21mm
013-0402007
3/8"
FLAT WASHER
22mm O.D.
013-0102019
1/4"
LOCK WASHER
026-01M0238
2" ALUMINUM
FLATHEAD CAP
013-0402005
3/8"
FLAT WASHER
LARGE, USS, 25mm
013-0102020
3/8"
LOCK WASHER
016-0009003
1" SHIM WASHER
013-0003004
1 1/16"
FENDER WASHER
013-0102003
1/2"
FLAT WASHER
SMALL, SAE, 27mm
013-0102018
1/2"
LOCK WASHER
013-0102026
1/2"
FLAT WASHER
LARGE, USS, 34mm
014-0018001
1/2" LONG
SPACER
013-0003002
3/8" FENDER WASHER
026-01PL151
PLASTIC 1 1/16"
FENDER WASHER
014-0018002
1" LONG
SPACER
PAGE 21
V3-PRESS ARM ASSEMBLY
OWNER'S MANUAL
WASHER SIZING CHART
(CONTINUED)
026-01M0211
1/4" LONG
FLANGED SPACER
026-01M211T
1/4" LONG HEAVY
FLANGED SPACER
026-01M0788
.81" LONG HEAVY
FLANGED SPACER
026-01M0789
.44" LONG HEAVY
FLANGED SPACER
026-01M0600
.625" LONG
FLANGED SPACER
V3-PRESS ARM ASSEMBLY
026-01M0198
1/2" LONG
FLANGED SPACER
026-01M0532
11/16" LONG HEAVY
FLANGED SPACER
026-01M0780
.65" LONG HEAVY
FLANGED SPACER
026-01M0762
1 1/2" LONG HEAVY
FLANGED SPACER
026-01M0240
1 3/8" ALUMINUM
FLATHEAD CAP
026-01M0760
1/2" LONG HEAVY
FLANGED SPACER
026-01M0551
1" LONG HEAVY
FLANGED SPACER
026-01M0761
1 11/16" LONG HEAVY
FLANGED SPACER
026-01M0768
1 1/4" LONG HEAVY
FLANGED SPACER
026-01M0239
1 5/8" ALUMINUM
FLATHEAD CAP
PAGE 22
OWNER'S MANUAL
MAINTENANCE SCHEDULE
ROUTINE
COMMERCIAL
MAINTENANCE
HOME
MAINTENANCE
Inspect;
Links, Pull Pins, Snap Locks,
Swivels, Weight Stack Pins
DAILY
WEEKLY
Clean;
Upholstery
DAILY
WEEKLY
Inspect;
Cables or Belts and their
tension
DAILY
WEEKLY
Inspect;
Accessory Bars, and Handles
WEEKLY
3 MONTHS
Inspect;
All Decals
WEEKLY
3 MONTHS
WEEKLY
3 MONTHS
Inspect;
Anti-Skid Surface
WEEKLY
3 MONTHS
Clean & Lubricate;
Guide Rods with a Teflon (PTFE)
based lubricant (Superlube)
MONTHLY
3 MONTHS
Lubricate;
Seat Sleeves, Turcite Bushings,
Linear Bearing
MONTHLY
3 MONTHS
Clean and Wax;
All Glossy Finishes
6 MONTHS
YEARLY
Repack with Grease;
Linear Bearings
6 MONTHS
YEARLY
YEARLY
3 YEARS
Inspect;
All Nuts and Bolts, Tighten if needed
Replace;
Cables, Belts and Connecting Parts
LATEST DATE ENTRY
Your equipment comes with a commercial maintenance decal.
For personal, in home use, please follow the home maintenance schedule listed above.
PAGE 23
V3-PRESS ARM ASSEMBLY
OWNER'S MANUAL
HOIST FITNESS SYSTEMS
GENERAL MAINTENANCE INFORMATION
Links, Pull-Pins, Snap Hooks, Swivels, Weight Stack Pins:
*Check all pieces for signs of visible wear or damage.
*Check springs in snap hooks and pull-pins for proper tension and alignment.
*If the spring sticks or has lost its rigidity, replace it immediately.
Upholstery:
*To ensure prolonged upholstery life and proper hygiene, all upholstered pads should be wiped down with a damp cloth after every workout.
*Periodically take the time to use a mild soap or an approved vinyl upholstery cleaner to deter the onset of cracking or drying. Avoid using any
abrasive cleaners or cleaners not intended for use on vinyl.
*Replace ripped or warn upholstery immediately.
*Keep sharp or pointed objects clear of all upholstery.
Decals:
*Inspect and familiarize yourself with any safety warnings or other user information posted on each decal.
Nuts and Bolts:
*Inspect all nuts and bolts for any loosening and tighten if needed.
*Go through a re-tightening sequence periodically to ensure that all hardware is tensioned proper.
Anti-Skid Surfaces:
*These surfaces are designed to supply secure footing and need to be replaced if they appear worn or become slippery.
Belts and Cables:
*Hoist uses only high quality belt, and mil-spec cables.
*Visually inspect the belts and cables for fraying, cracking, peeling or discoloration.
*While the machine is not in use, carefully run your fingers along the belt or cable to feel for thinning or bulging areas.
*Replace belts and cables immediately at the first signs of damage or wear. Do not use equipment until belts or cables have been replaced.
Belt and Cable Tension:
*Referring to the Owners Manual, when belts or cables are used check all bolts attachments to be sure they are properly attached.
*Check slack in cables and re-adjust cable tension if needed.
Seat Sleeves, Guide Rods:
*Wipe down adjusting tubes with a dust free rag before applying lubricant.
*Lubricate seat sleeves and Guide Rods with a Silicon or Teflon based lubricant spray.
Linear Bearings:
*Referring to the Owners Manual carefully disassemble the bearing from its housing and place a finger full of light grease (lithium, super lube,
etc.) into the inside of the bearing. Using your finger, press the grease into the ball-bearings and their tracks. repeat until the ball-bearing
tracks are full of grease. Insert the shaft back into the bearing and wipe off excess grease.
PLEASE KEEP THIS FOR YOUR RECORDS
V3-PRESS ARM ASSEMBLY
PAGE 24
OWNER'S MANUAL
WEIGHT TRAINING TIPS
Use this manual to guide you through the basic exercises you can perform on
your V3-PRESS ARM HOIST® Fitness System. To gain maximum results and
avoid possible injury, consult a fitness professional to develop your complete
exercise program.
Always consult your physician before starting any exercise program.
To be successful in your exercise program, it is important to develop an
understanding of the basic principles of strength training. Now that you have
your V3-PRESS ARM HOIST® Fitness System, it is only natural that you want to
get started immediately. First, determine a set of realistic goals and objectives
for yourself. By deciding on an exercise plan that is right for you prior to starting,
you will contribute significantly to your success.
Warm up properly before engaging in weight resistance training. Stretching,
yoga, jogging, calisthenics or other cardiovascular exercise can help prepare
your body for the heavier workload of lifting weights.
Learn how to perform the exercise correctly before using heavy weight.
Correct form is important to avoid injury and to ensure that you work the proper
muscle groups.
Know your limitations. If you are new to weight training or are embarking on
an exercise regimen after a long layoff, start slowly and build foundational
strength over a longer period of time.
Pay attention to your breathing. Exhale when you exert is a general rule of
thumb. Never hold your breath.
Enjoy your V3-PRESS ARM HOIST® Fitness System!
PAGE 25
V3-PRESS ARM ASSEMBLY
OWNER'S MANUAL
***THIS PAGE WAS INTENTIONALLY LEFT BLANK***
V3-PRESS ARM ASSEMBLY
PAGE 26
OWNER'S MANUAL
Date
Exercise
Totals
S = Sets R = Repetition per set W = Weight used
WEIGHT TRAINING EXERCISE LOG
S R W S R W S R W S R W S R W S R W S R W S R W S R W S R W S R W S R W
V3-PRESS ARM ASSEMBLY
PAGE 27
OWNER'S MANUAL
HOIST FITNESS SYSTEMS
LIMITED LIFETIME WARRANTY
Hoist Fitness Systems warrants this product to the original purchaser to be free from defects in workmanship and/or
materials under normal use or service. If at any time a component part is defective, Hoist Fitness Systems shall repair or
replace it (at Hoist Fitness Systems option) within a reasonable period of time. This warranty does not cover costs of removal.
transportation or reinstallation. This warranty shall not apply if the defect was caused by misuse, neglect or normal wear and
tear.
WARRANTY CLAIMS. All claims require: Model number, Serial
number, Date of installation, and any information supporting the
existence of the alleged defect.
To complete Warranty Registration visit:
www.HOISTFITNESS.com
and click on the Warranty Registration link
Starting from the original date of purchase, normal wear and tear shall be considered as the following:
COMMERCIAL USE: All malfunctions of upholstery, grips, paint, and chrome that occur after one year; all malfunctions of
electronic components, belts, or cables after one year; all malfunctions of pulleys, bearings, or bushings that occur after five
years. The frame and all welded components are warranted for the life of the product.
HOME USE: All malfunctions of grips, paint, and chrome that occur after ten years; all malfunctions of electronic
components, belts, cables, or upholstery that occur after ten years; all malfunctions of pulleys, bearings, or bushings that
occur after ten years. The frame and all welded components are warranted for the life of the product.
PLEASE NOTE THAT NOT ALL HOIST PRODUCTS ARE MADE FOR COMMERCIAL USE.
Refer to the instructions page of your owners manual or consult with you fitness product dealer to establish if a product is
made for commercial use or not. Using a non-commercial product in a commercial setting can result in serious injury or
death!
Hoist Fitness Systems sole responsibility shall be to repair or replace the component within the terms stated above. Hoist
Fitness Systems shall not be liable for any loss or damage of any kind including any incidental or consequential damages
resulting, directly or indirectly from any warranty expressed or implied or any other failure of this product.
WHAT IS NOT COVERED BY THIS WARRANTY
Hoist's sole obligation under this warranty is limited to either repair or replacement of parts, subject to the additions below.
This warranty neither assumes nor authorizes any person to assume obligations other than expressly covered by this
warranty.
NO CONSEQUENTIAL DAMAGES. Hoist is not responsible for economic loss; profit loss; or special, indirect, or
consequential damages.
WARRANTY IS NOT TRANSFERABLE. This warranty is not assignable and applies only in favor of the original
purchaser/user to whom delivered. Any such assignment or transfer shall void the warranties herein made and shall void all
warranties, expressed, implied or statutory, except the one (1) and five (5) year warranties described above. These
warranties are exclusive and in lieu of all other warranties, including implied warranty and merchantability or fitness for a
particular purpose. There are no warranties which extend beyond the description on the face hereof.
TRANSPORTATION COSTS. Hoist will accept parts covered under this warranty freight collect, provided that shipment
has received prior approval. Hoist is not responsible for any other transportation costs, but will ship freight collect parts either
repaired or replaced under these warranties.
Hoist Fitness Systems
9990 Empire St. #130
San Diego, CA. 92126
(800)548-5438
PLEASE KEEP THIS FOR YOUR RECORDS
V3-PRESS ARM ASSEMBLY
PAGE 28
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising