HoistFitness | V-PREMIER | Owner Manual | HoistFitness V-PREMIER Owner Manual

HoistFitness V-PREMIER Owner Manual
OWNER'S MANUAL
V-PREMIER
MULTI-FUNCTION GYM
Note: Both Serial Number and Model Number are Required when Ordering Parts
RECORD SERIAL NUMBER HERE
CATALOG NUMBER
0109 - 001
Customer Service
(800) 548-5438
(858) 578-7676
Fax
(858) 578-9558
OWNER'S MANUAL
CONTENTS
INSTRUCTIONS ..................................................................... 02
FRAME ASSEMBLY .............................................................. 04
ACCESSORIES/MISC............................................................ 53
PRE-ASSEMBLY.................................................................... 54
DECAL PLACEMENT............................................................. 55
DECAL REFERENCE............................................................. 56
PART LIST............................................................................... 59
ABBREVIATIONS................................................................... 62
BOLT SIZING CHART............................................................ 63
WASHER SIZING CHART...................................................... 65
MAINTENANCE SCHEDULE................................................. 67
GENERAL MAINTENANCE INFORMATION........................ 68
WEIGHT TRAINING TIPS....................................................... 69
EXERCISE LOG...................................................................... 71
LIMITED WARRANTY............................................................ 72
PAGE 01
V-PREMIER ASSEMBLY
OWNER'S MANUAL
INSTRUCTIONS
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.
HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted for, continue on.
TOOLS REQUIRED
Ratchet Wrench
1/2", 9/16" and 3/4" Sockets
Adjustable Wrench
Rubber Mallet
Tape Measure
Level
Hex Key Wrench Set
Two People
V-PREMIER ASSEMBLY
PAGE 02
OWNER'S MANUAL
***THIS PAGE WAS INTENTIONALLY LEFT BLANK***
PAGE 03
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
V-PREMIER ASSEMBLY
PAGE 04
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
21
15
91
77
19
28
77
98
PAGE 05
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:.
- HAND TIGHTEN HARDWARE.
92
77
28
21
77
98
V-PREMIER ASSEMBLY
PAGE 06
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
45
28
77
80
87
PAGE 07
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
74
NOTE:
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
45
73
42
64
**OPTIONAL 200 LB. WEIGHT STACK**
CONSULT YOUR DEALER
FOR DETAILS
74
45
73
IF OPTIONAL 200 LB. WEIGHT STACK IS
PURCHASED, REMOVE AND DISCARD ALL
STAND-OFFS (64) AND ASSEMBLE WEIGHT
STACK WITH 5 MORE WEIGHT PLATES, AS
SHOWN TO THE RIGHT
V-PREMIER ASSEMBLY
42
PAGE 08
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
WARNING!
BE SURE TO HAVE ONE PERSON FULLY SUPPORT UPRIGHT (27) WHILE THE
OTHER ALIGNS AND FASTENS HARDWARE. FAILURE TO FOLLOW THESE
INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH.
27
94
77
46
55
77
55
98
46
PAGE 09
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
31
59
71
25
V-PREMIER ASSEMBLY
PAGE 10
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
98
77
77
27
59
25
PAGE 11
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
94
77
18
77
27
V-PREMIER ASSEMBLY
98
PAGE 12
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
BE SURE BUSHING (67) IS POSITIONED
AS SHOWN FOR PROPER GUIDE-ROD
ALIGNMENT.
30
67
18
30
67
18
PAGE 13
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
IMPORTANT
If you are installing a V HI-LO Option
refer to the V HI-LO owner's manual
and assemble the V HI-LO frame part
at this time.
87
77
18
22
77
98
V-PREMIER ASSEMBLY
PAGE 14
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
FOR INSTALLATION OF V LEG PRESS
OPTION, DISCARD THIS PLATE (60).
FOR INSTALLATION OF VR-COMBO
OPTION, DISCARD THIS PLATE (60).
*
**
IMPORTANT:
If you are installing a V Leg Press option
refer to the V Leg Press owner's manual
and assemble the V Leg Press frame
parts at this time.
IMPORTANT:
If you are installing a V HI-LO option
refer to the V HI-LO owner's manual
and assemble the V HI-LO frame
parts at this time.
95
77
*
60
**
60
77
98
IMPORTANT:
If you are installing a VR-COMBO option
refer to the VR-COMBO owner's manual
and assemble the VR-COMBO frame
parts at this time.
PAGE 15
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE (96) THEN
LOOSEN NUT JUST ENOUGH FOR (23)
TO PIVOT FREELY.
- WRENCH TIGHTEN ALL PREVIOUSLY HAND
TIGHTENEND HARDWARE.
96
78
28
78
23
99
*IMPORTANT*
NOW THAT THE V-PREMIER IS COMPLETELY ASSEMBLED TAKE TIME TO
ASSURE THAT YOUR UNIT IS ASSEMBLED SQUARE AND PERPENDICULAR. USE A LEVEL
TO CHECK THAT THE GUIDE RODS ARE PERPENDICULAR IN BOTH DIRECTIONS.
IF THEY ARE NOT PERPENDICULAR IN BOTH DIRECTIONS, IT WILL BE NECESSARY TO
LOOSEN SOME FRAME HARDWARE TO RE-ALIGN THE FRAME AND RETIGHTEN BOLTS.
V-PREMIER ASSEMBLY
PAGE 16
OWNER'S MANUAL
FRAME ASSEMBLY
18
49
PAGE 17
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
* HANGER ASSEMBLY ORIGINALLY
INCLUDED WITH V PRESS ARM.
18
*
49
V-PREMIER ASSEMBLY
PAGE 18
OWNER'S MANUAL
FRAME ASSEMBLY
*
NOTE:
* HANGER ASSEMBLY AND HARDWARE
ORIGINALLY INCLUDED WITH V PRESS
ARM.
- WRENCH TIGHTEN HARDWARE.
1/4"-20 UNC X .75" SHCS (BZ)
*
*
SPLIT COLLAR THREADED
1.00" I.D. X 20 mm
PAGE 19
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
CABLING PROFILE VIEW
NOTE:
BE SURE CABLE RUNS
BETWEEN THE PULLEYS AND
GUARD RODS AS SHOWN
54
66
NOTE:
WHEN ADJUSTING CABLE FOR
PROPER TENSION, INSURE THAT
BOTH PLATES (54) ARE RESTING
UNDER THE BUMPER STOP (66)
AS SHOWN.
V-PREMIER ASSEMBLY
PAGE 20
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
BE SURE TO POSITION
CABLE (4) BETWEEN
PULLEY(39) AND
GUARD PIN AS SHOWN
4
GUARD PIN
18
39 PULLEY
52
52
39
94
18
77
77
98
JAM BOLT
JAM NUT
FINE TUNING:
LOOSEN JAM NUT AND THREAD
BOLT IN/OUT TO GIVE THE CABLE
PROPER TENSION. RE-TIGHTEN
JAM NUT.
WARNING - CABLE BOLT MUST BE THREADED
A MINIMUM OF 3/8" WITH JAM NUT TIGHTENED
SECURELY TO ENSURE PROPER CONNECTION.
4
PAGE 21
143 1/8" 3635
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
88
77
18
77
98
54
4
V-PREMIER ASSEMBLY
38
PAGE 22
OWNER'S MANUAL
FRAME ASSEMBLY
53
38
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
33
4
94
38
46
48
18
98
PROPERLY INSTALLED VIEW
4
PAGE 23
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
90
77
77
98
4
41
27
V-PREMIER ASSEMBLY
PAGE 24
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
* THIS PART ORIGINALLY INCLUDED
IN V-PRESS-ARM UNIT.
88
77
77
98
*
4
PAGE 25
38
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
PROPERLY INSTALLED VIEW
98
79
41
41
4
4
79
93
V-PREMIER ASSEMBLY
PAGE 26
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
* THIS PART ORIGINALLY INCLUDED
IN V-PRESS ARM UNIT.
4
38
*
77
98
*
77
88
38
4
PAGE 27
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
4
38
94
18
47
47
PROPERLY INSTALLED VIEW
98
BE SURE TO POSITION
CABLE (4) BETWEEN
PULLEY (38) AND
GUARD PIN AS SHOWN
GUARD PIN
4
38
V-PREMIER ASSEMBLY
PAGE 28
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
94
77
18
77
98
13
PAGE 29
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
4
40
PROPERLY INSTALLED VIEW
BE SURE TO POSITION
CABLE (4) BETWEEN
PULLEY (40) AND
GUARD PIN AS SHOWN
40
94
4
77
77
GUARD PIN
98
V-PREMIER ASSEMBLY
PAGE 30
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
REAR CABLE PROFILE VIEW
CABLE PROFILE VIEW
3
PAGE 31
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
53
JAM NUT
3
JAM BOLT
3
77
38
98
FINE TUNING:
LOOSEN JAM NUT AND THREAD
BOLT IN/OUT TO GIVE THE CABLE
PROPER TENSION. RE-TIGHTEN
JAM NUT.
88
77
14
WARNING - CABLE BOLT MUST BE THREADED
A MINIMUM OF 3/8" WITH JAM NUT TIGHTENED
SECURELY TO ENSURE PROPER CONNECTION.
241 3/4" 6142
V-PREMIER ASSEMBLY
3
PAGE 32
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
88
77
77
98
54
38
PAGE 33
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
3
38
88
77
14
77
98
V-PREMIER ASSEMBLY
PAGE 34
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
94
38
77
3
94
50
77
98
38
38
48
BE SURE TO POSITION
CABLE (3,4) BETWEEN
PULLEY(38) AND
GUARD BOLT (94) AS SHOWN
98
94
3
4
38
PAGE 35
38
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
FINE TUNING:
LOOSEN JAM NUT AND THREAD
BOLT IN/OUT TO GIVE THE CABLE
PROPER TENSION. RE-TIGHTEN
JAM NUT.
WARNING - CABLE BOLT MUST BE THREADED
A MINIMUM OF 3/8" WITH JAM NUT TIGHTENED
SECURELY TO ENSURE PROPER CONNECTION.
JAM BOLT
JAM NUT
59
3
59
14
V-PREMIER ASSEMBLY
PAGE 36
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
CABLE PROFILE VIEW
6
PAGE 37
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
* HARDWARE PART OF CABLE (6) ASSEMBLY
*
6
*
FINE TUNING:
LOOSEN JAM NUT AND THREAD
BOLT IN/OUT TO GIVE THE CABLE
PROPER TENSION. RE-TIGHTEN
JAM NUT.
WARNING - CABLE BOLT MUST BE THREADED
A MINIMUM OF 3/8" WITH JAM NUT TIGHTENED
SECURELY TO ENSURE PROPER CONNECTION.
60
14
6
6
6
17 3/4" 451
V-PREMIER ASSEMBLY
PAGE 38
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
CABLE PROFILE VIEW
5
PAGE 39
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
* HARDWARE PART OF CABLE (5) ASSEMBLY
FINE TUNING:
14
LOOSEN JAM NUT AND THREAD
BOLT IN/OUT TO GIVE THE CABLE
PROPER TENSION. RE-TIGHTEN
JAM NUT.
WARNING - CABLE BOLT MUST BE THREADED
A MINIMUM OF 3/8" WITH JAM NUT TIGHTENED
SECURELY TO ENSURE PROPER CONNECTION.
5
14
5
*
5
*
*
60
60
23 11/16" 602
V-PREMIER ASSEMBLY
5
PAGE 40
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
CABLING PROFILE VIEW
IMPORTANT:
If you are installing a V HI-LO Option, do not
install cable (2). Refer to the V HI-LO owner's
manual and follow assembly steps to install
CABLE ASSEMBLY: V HI-LO AB 167.91" LG.
(item # 1 in V HI-LO owner's manual) in place
of cable (2).
2
PAGE 41
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
PROPERLY INSTALLED VIEW
41
2
90
41
77
41
90
77
23
2
77
41
98
77
98
2
129 1/16" 3278
V-PREMIER ASSEMBLY
PAGE 42
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
77
89
98
77
14
38
2
PAGE 43
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
2
95
51
58
41
98
46
25
V-PREMIER ASSEMBLY
PAGE 44
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
77
90
98
77
41
27
PAGE 45
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
PROPERLY INSTALLED VIEW
93
41
BE SURE TO POSITION
CABLE (2) BETWEEN
PULLEY (41) AND
GUARD BOLT (93) AS
SHOWN.
GUARD BOLT
93
2
79
2
79
98
V-PREMIER ASSEMBLY
41
PAGE 46
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
9
26
76
84
PAGE 47
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
26
85
28
V-PREMIER ASSEMBLY
PAGE 48
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
10
24
76
84
76
84
PAGE 49
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
27
24
85
V-PREMIER ASSEMBLY
PAGE 50
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- REPEAT ASSEMBLY FOR OPPOSITE SIDE.
22
77
82
86
57
77
28
82
86
56
77
82
86
77
82
86
PAGE 51
V-PREMIER ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- WRENCH TIGHTEN ALL PREVIOUSLY HAND
TIGHTENED HARDWARE.
- REPEAT ASSEMBLY FOR OPPOSITE SIDE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
77
82
86
77
82
86
V-PREMIER ASSEMBLY
PAGE 52
OWNER'S MANUAL
ACCESSORIES/MISC
NOTE:
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
12
43
108
109
110
11
43
43
43
8
20
20
16
PAGE 53
V-PREMIER ASSEMBLY
OWNER'S MANUAL
PRE-ASSEMBLY
44
62
62
97
74
36
34
29
1
75
34
53
18
68
66
69
63
17
72
63
59
31
7
73
65
37
37
70
75
19
81
83
75
32
27
81
21
83
61
61
23
61
61
32
35
28
V-PREMIER ASSEMBLY
PAGE 54
OWNER'S MANUAL
DECAL PLACEMENT
NOTE:
- ALL DECALS ARE CENTERED
UNLESS OTHERWISE STATED.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
106
106
104
103
107
102
100
105
101
PAGE 55
V-PREMIER ASSEMBLY
OWNER'S MANUAL
DECAL REFERENCE
021-0018022
SERIAL # DECAL
6
5
4
3
2
1
021-0003754
021-0004064
021-0003675
V-PREMIER ASSEMBLY
PAGE 56
OWNER'S MANUAL
DECAL REFERENCE
021-0003008
021-0003135
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
021-0003198
PAGE 57
V-PREMIER ASSEMBLY
OWNER'S MANUAL
***THIS PAGE WAS INTENTIONALLY LEFT BLANK***
V-PREMIER ASSEMBLY
PAGE 58
OWNER'S MANUAL
PART LIST
NOTE: SOME OF THESE PARTS MAY COME PRE-INSTALLED
ITEM NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
PAGE 59
PART NUMBER
010-0008001
010-01C0393T
010-01C0394T
010-01C0395T
010-01C0398
010-01C0399
020-0014027
020-0014028
022-01PD2014-A
022-01PD2304-A
026-01X1118
026-01X1119
026-01X1404
026-01X1414
026-01X1419
026-01X1635
026-01X2039
026-01X3104
026-01X3160
026-01X4057
026-01X5007
026-01X5012
026-01X5079
026-01X5096
026-01X5164
026-01X5303
026-01X5307
026-01X5308
010-0008002
011-0112002
012-0305003
014-0003003
014-0018001
014-0101005
014-0101014
014-0101020
016-0002007
018-0001002
018-0001003
018-0002014
DESCRIPTION
LANYARD COIL
MID PULLEY CABLE ASSEMBLY: 129.06" LG.
FLOATING PULLEY CABLE ASSEMBLY: 241.81" LG.
WT. STACK CABLE ASSEMBLY: 143.13" LG.
ANCHOR CABLE ASSEMBLY: 23.69" LG.
ANCHOR CABLE ASSEMBLY: 17.75" LG.
ADJUSTABLE STOP
14 LINK CHAIN
UPHOLSTERY PAD W/ACX BACKING
PAD ASSEMBLY
ALUMINUM CURL BAR ASSEMBLY
ALUMINUM LAT BAR ASSEMBLY
BAR MOUNT ASSEMBLY
ADJ. FLOATING PULLEY HOUSING ASSEMBLY
FRAME BASE ASSEMBLY
FLEECE KNEE STRAP WITH (3) D-RINGS ASSEMBLY
RADIAL CAST WT.SELECTOR PIN ASSEMBLY
TOP MAIN FRAME ASSEMBLY
RATCHET PULL-PIN ASSEMBLY
STRAP HANDLE WITH (3) D-RINGS (LOWER) ASSEMBLY
ACCESSORY RACK ASSEMBLY
SHIELD MOUNT - TOP ASSEMBLY
SWIVEL PULLEY ASSEMBLY
BACK PAD ADJUSTER ASSEMBLY
PULLEY GUIDE ROD ASSEMBLY
PAD MOUNT ASSEMBLY
MAIN UPRIGHT ASSEMBLY
SEAT FRAME
LANYARD PIN
1/2" X .500" SHSS (WZ)
3/8"-16UNC JAM NUT (WZ)
.50" I.D.
BEARING: FLANGED BALL BEARING
PULLEY SPACER: .39" I.D. X .50" LG.
BUSHING: OILITE FLANGED Ø1.38" O.D. X Ø1.00" I.D. X .81" LG.
FLANGED OILITE 0.75" I.D. X .60" L.G.
BUSHING: OILITE FLANGED Ø.63" O.D. X Ø.38" I.D. X .50" LG.
VINYL SLEEVE Ø.38" X 1.63"
CABLE PULLEY: Ø3.50"
CABLE PULLEY: Ø4.50"
CABLE PULLEY: WIDE (BORED HUB) Ø4.50"
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
2
2
2
1
2
1
2
2
11
1
1
V-PREMIER ASSEMBLY
OWNER'S MANUAL
PART LIST CONTINUED
NOTE: SOME OF THESE PARTS MAY COME PRE-INSTALLED
ITEM NO.
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
PART NUMBER
018-0002015
019-0001006
020-0010002
030-0303006
026-01G0177
026-01M0760
026-01M0761
026-01M1018
026-01M2268
026-01M2466
026-01M2539
026-01M2553
026-01M2559
026-01P1689
026-01P3368
026-01P6011
026-01P6012
026-01P6073
026-01P6224
026-01P6394
026-01PL0125
026-01PL0134
026-01PL0269
026-01PL0369
026-01PL0371
026-01PL0381
026-01PL2201
026-01PL2245
026-01PL2316
026-01PL2413
026-01PL2422
026-01W0139
026-01W0142
026-STD-SWTOP9
013-0002003
013-0302008
013-0402007
013-0102003
013-0102028
013-0102020
V-PREMIER ASSEMBLY
DESCRIPTION
3.50"
CABLE PULLEY: WIDE (BORED HUB)
THICK RUBBER DONUT 3.00" X .50" BLACK
SNAP LINK
ROLL PIN Ø.44" O.D. X 3.00" LG. (WZ)
GUIDE ROD Ø.75" X 71.44" LG.
HEAVY FLANGED SPACER: Ø.67" O.D. X Ø.39" I.D. X .50" LG.
HEAVY FLANGED SPACER: Ø.39" I.D X 1.69" LG.
.67" I.D. X .25" LG.
HEAVY FLANGED SPACER:
SHAFT: Ø 1.00 X 6.56" LG.
HEAVY FLANGED SPACER: Ø.39" I.D X 3.13" LG.
HEAVY FLANGED SPACER Ø.39" I.D. X 2.36" LG.
SPACER .75" O.D. X .39" I.D. X 1.50" LG.
THREADED CABLE ANCHOR
DOUBLE PULLEY MOUNT PLATE
GUSSET PLATE
SHIELD, LEFT
SHIELD, RIGHT
PULLEY PLATE
ANTI-TWIST BRKT
CABLE ANCHOR PLATE
E-Z GLIDE PLASTIC SLEEVE
GUIDE ROD BUSHING
CAST WEIGHT BUSHING
WEIGHT STAND OFF
DELRIN BUSHING
BUMPER, HALF ROUND, DUAL STEM
PLASTIC SLEEVE .75" O.D.
PLASTIC FLANGED BUSHING Ø.75" O.D X Ø.50" I.D X .38" LG.
ENDCAP (DOMED) - GREY 1.00"
SLOT COVER
STOP DISK
21 HOLE STEM
10 LBS. INTERMEDIATE RADIAL LOC WEIGHT PLATE
CAST RADIAL TOP WEIGHT
1/4" X 16mm SAE FLAT WASHER (WZ)
5/16" SAE FLAT WASHER (WZ)
3/8" X 22mm FLAT WASHER (WZ)
1/2" X 27mm SAE FLAT WASHER (WZ)
3/8" CURVED WASHER (WZ)
3/8" SPLIT LOCK WASHER (WZ)
QTY.
7
2
4
1
2
6
2
2
1
1
1
2
1
2
2
1
1
1
1
2
4
2
28
2
1
1
2
1
1
1
1
1
14
1
3
4
74
2
6
2
PAGE 60
OWNER'S MANUAL
PART LIST CONTINUED
NOTE: SOME OF THESE PARTS MAY COME PRE-INSTALLED
ITEM NO.
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
PAGE 61
PART NUMBER
013-0102023
013-0102022
011-0102008
011-0107011
011-0311013
011-0101041
011-0107037
011-0407027
011-0407058
011-0107026
011-0407026
011-0107020
011-0407025
011-0107022
011-0407070
011-0407000
012-0104009
012-0104008
012-0304011
021-0003008
021-0003135
021-0003198
021-0003675
021-0003754
021-0004064
021-0018022
SERIAL # DECAL
026-01WADD-08
026-01WADD-09
022-0008032
DESCRIPTION
1/4" INTERNAL LOCK WASHER
3/8" INTERNAL LOCK WASHER
1/4"-20UNC X.75" BHCS (WZ)
5/16"-18UNC X 1.25" HHB (WZ)
3/8-16UNC X .75" SQUARE HEAD (WZ)
3/8"-16UNC X .75" BHCS (WZ)
3/8"-16UNC X 1.25" HHB (WZ)
3/8"-16UNC X 1.75" HHB (WZ)
3/8"-16UNC X 2.00" HHB (WZ)
3/8"-16UNC X 2.25" HHB (WZ)
3/8"-16UNC X 3.00" HHB (WZ)
3/8"-16UNC X 3.25" HHB (WZ)
3/8"-16UNC X 4.00" HHB (WZ)
3/8"-16UNC X 5.00" HHB (WZ)
3/8"-16UNC X 5.25" HHB (WZ)
1/2"-13UNC X 3.50" HHB (WZ)
1/4"-20 UNC THIN NYLOCK NUT (WZ)
3/8"-16 UNC THIN NYLOCK NUT (WZ)
1/2"-13 UNC THIN NYLOCK NUT (WZ)
DECAL COMMERCIAL MAINTENANCE 1.50" X 6.69"
DECAL WARNING 1.50" X 6.69"
DECAL 200 lb RADIAL WEIGHT STACK # (1-20)
DECAL V BACK ADJUSTER
DECAL V-PREMIER EMBLEM
DECAL ADJUST 1-6 VERTICAL TXT.
DECAL HOISTFITNESS.COM LOGO
DECAL HOIST SERIAL # 1.63" X 2.63"
ADD ON WEIGHT, 5 LB
ADD ON WEIGHT, 2.5 LB
AB STRAP
QTY.
2
8
2
4
2
8
4
6
1
4
4
2
3
15
3
1
1
41
1
1
1
1
1
1
1
2
1
1
1
1
V-PREMIER ASSEMBLY
OWNER'S MANUAL
ABBREVIATIONS
BZ = Black Zinc
WZ = White Zinc
HHB = Hex Head Bolt
FHCS = Flat Head Cap Screw
BHCS = Button Head Cap Screw
SHCS = Socket Head Cap Screw
SHSS = Socket Head Shoulder Screw
V-PREMIER ASSEMBLY
PAGE 62
OWNER'S MANUAL
BOLT SIZING CHART
1 3/4"
5/16" HHB
1 1/4"
2 1/4"
5 1/4"
4 1/2"
3 1/2"
4"
3"
2"
4 3/4"
4 1/4"
3 1/4"
2 1/2"
1 1/2"
1"
3 3/4"
2 3/4"
5 1/2"
5"
0"
2 3/4"
1 3/4"
3/8" HHB
2 1/4"
1 1/4"
0"
1"
2"
1"
1/2" SHSS
1 1/4"
1 1/2"
0"
PAGE 63
1"
4"
5"
3 1/4"
2 1/2"
2"
5 1/2"
3 3/4"
2 3/4"
2 1/4"
5 1/4"
4 1/2"
3 1/2"
3"
1 3/4"
4 3/4"
4 1/4"
3 1/4"
5 1/2"
5"
3 3/4"
2 1/2"
1 1/2"
0"
4"
2 3/4"
2 1/4"
1 1/4"
5 1/4"
4 1/2"
3 1/2"
3"
2"
1 3/4"
1/2" HHB
4 1/4"
3 1/4"
2 1/2"
1 1/2"
4 3/4"
3 3/4"
3 1/2"
3"
4"
V-PREMIER ASSEMBLY
OWNER'S MANUAL
BOLT SIZING CHART
(CONTINUED)
3/8" FHCS
3/4"
1 3/4"
1 1/4"
2 3/4"
2 1/4"
1 1/2"
1"
0"
2 1/2"
3"
2"
3/8" BHCS
3/8" SHCS
3/4"
1"
3/4"
0"
0"
1/2" FHCS
1/4" HHB
3/4"
3/4"
1 1/4"
1 1/2"
0"
1"
0"
V-PREMIER ASSEMBLY
1"
PAGE 64
OWNER'S MANUAL
WASHER SIZING CHART
013-0002003
1/4"
FLAT WASHER
SMALL, SAE, 13mm
013-0102028
3/8"
CURVED WASHER
013-0102004
5/16"
FLAT WASHER
LARGE, USS, 22mm
013-0002004
3/8"
FLAT WASHER
SMALL, SAE, 21mm
013-0402007
3/8"
FLAT WASHER
22mm O.D.
013-0102019
1/4"
LOCK WASHER
026-01M0238
2" ALUMINUM
FLATHEAD CAP
013-0402005
3/8"
FLAT WASHER
LARGE, USS, 25mm
013-0102020
3/8"
LOCK WASHER
016-0009003
1" SHIM WASHER
013-0003004
1 1/16"
FENDER WASHER
013-0102003
1/2"
FLAT WASHER
SMALL, SAE, 27mm
013-0102018
1/2"
LOCK WASHER
013-0102026
1/2"
FLAT WASHER
LARGE, USS, 34mm
014-0018001
1/2" LONG
SPACER
013-0003002
3/8" FENDER WASHER
026-01PL151
PLASTIC 1 1/16"
FENDER WASHER
014-0018002
1" LONG
SPACER
PAGE 65
V-PREMIER ASSEMBLY
OWNER'S MANUAL
WASHER SIZING CHART
(CONTINUED)
026-01M0211
1/4" LONG
FLANGED SPACER
026-01M211T
1/4" LONG HEAVY
FLANGED SPACER
026-01M0788
.81" LONG HEAVY
FLANGED SPACER
026-01M0789
.44" LONG HEAVY
FLANGED SPACER
026-01M0600
.625" LONG
FLANGED SPACER
V-PREMIER ASSEMBLY
026-01M0198
1/2" LONG
FLANGED SPACER
026-01M0532
11/16" LONG HEAVY
FLANGED SPACER
026-01M0780
.65" LONG HEAVY
FLANGED SPACER
026-01M0762
1 1/2" LONG HEAVY
FLANGED SPACER
026-01M0240
1 3/8" ALUMINUM
FLATHEAD CAP
026-01M0760
1/2" LONG HEAVY
FLANGED SPACER
026-01M0551
1" LONG HEAVY
FLANGED SPACER
026-01M0761
1 11/16" LONG HEAVY
FLANGED SPACER
026-01M0768
1 1/4" LONG HEAVY
FLANGED SPACER
026-01M0239
1 5/8" ALUMINUM
FLATHEAD CAP
PAGE 66
OWNER'S MANUAL
MAINTENANCE SCHEDULE
ROUTINE
COMMERCIAL
MAINTENANCE
HOME
MAINTENANCE
Inspect;
Links, Pull Pins, Snap Locks,
Swivels, Weight Stack Pins
DAILY
WEEKLY
Clean;
Upholstery
DAILY
WEEKLY
Inspect;
Cables or Belts and their
tension
DAILY
WEEKLY
Inspect;
Accessory Bars, and Handles
WEEKLY
3 MONTHS
Inspect;
All Decals
WEEKLY
3 MONTHS
WEEKLY
3 MONTHS
Inspect;
Anti-Skid Surface
WEEKLY
3 MONTHS
Clean & Lubricate;
Guide Rods with a Teflon (PTFE)
based lubricant (Superlube)
MONTHLY
3 MONTHS
Lubricate;
Seat Sleeves, Turcite Bushings,
Linear Bearing
MONTHLY
3 MONTHS
Clean and Wax;
All Glossy Finishes
6 MONTHS
YEARLY
Repack with Grease;
Linear Bearings
6 MONTHS
YEARLY
YEARLY
3 YEARS
Inspect;
All Nuts and Bolts, Tighten if needed
Replace;
Cables, Belts and Connecting Parts
LATEST DATE ENTRY
Your equipment comes with a commercial maintenance decal.
For personal, in home use, please follow the home maintenance schedule listed above.
PAGE 67
V-PREMIER ASSEMBLY
OWNER'S MANUAL
HOIST FITNESS SYSTEMS
GENERAL MAINTENANCE INFORMATION
Links, Pull-Pins, Snap Hooks, Swivels, Weight Stack Pins:
*Check all pieces for signs of visible wear or damage.
*Check springs in snap hooks and pull-pins for proper tension and alignment.
*If the spring sticks or has lost its rigidity, replace it immediately.
Upholstery:
*To ensure prolonged upholstery life and proper hygiene, all upholstered pads should be wiped down with a damp cloth after every workout.
*Periodically take the time to use a mild soap or an approved vinyl upholstery cleaner to deter the onset of cracking or drying. Avoid using any
abrasive cleaners or cleaners not intended for use on vinyl.
*Replace ripped or warn upholstery immediately.
*Keep sharp or pointed objects clear of all upholstery.
Decals:
*Inspect and familiarize yourself with any safety warnings or other user information posted on each decal.
Nuts and Bolts:
*Inspect all nuts and bolts for any loosening and tighten if needed.
*Go through a re-tightening sequence periodically to ensure that all hardware is tensioned proper.
Anti-Skid Surfaces:
*These surfaces are designed to supply secure footing and need to be replaced if they appear worn or become slippery.
Belts and Cables:
*Hoist uses only high quality belt, and mil-spec cables.
*Visually inspect the belts and cables for fraying, cracking, peeling or discoloration.
*While the machine is not in use, carefully run your fingers along the belt or cable to feel for thinning or bulging areas.
*Replace belts and cables immediately at the first signs of damage or wear. Do not use equipment until belts or cables have been replaced.
Belt and Cable Tension:
*Referring to the Owners Manual, when belts or cables are used check all bolts attachments to be sure they are properly attached.
*Check slack in cables and re-adjust cable tension if needed.
Seat Sleeves, Guide Rods:
*Wipe down adjusting tubes with a dust free rag before applying lubricant.
*Lubricate seat sleeves and Guide Rods with a Silicon or Teflon based lubricant spray.
Linear Bearings:
*Referring to the Owners Manual carefully disassemble the bearing from its housing and place a finger full of light grease (lithium, super lube,
etc.) into the inside of the bearing. Using your finger, press the grease into the ball-bearings and their tracks. repeat until the ball-bearing
tracks are full of grease. Insert the shaft back into the bearing and wipe off excess grease.
PLEASE KEEP THIS FOR YOUR RECORDS
V-PREMIER ASSEMBLY
PAGE 68
OWNER'S MANUAL
WEIGHT TRAINING TIPS
Use this manual to guide you through the basic exercises you can perform on
your V-PREMIER HOIST® Fitness System. To gain maximum results and avoid
possible injury, consult a fitness professional to develop your complete exercise
program.
Always consult your physician before starting any exercise program.
To be successful in your exercise program, it is important to develop an
understanding of the basic principles of strength training. Now that you have
your V-PREMIER HOIST® Fitness System, it is only natural that you want to get
started immediately. First, determine a set of realistic goals and objectives for
yourself. By deciding on an exercise plan that is right for you prior to starting,
you will contribute significantly to your success.
Warm up properly before engaging in weight resistance training. Stretching,
yoga, jogging, calisthenics or other cardiovascular exercise can help prepare
your body for the heavier workload of lifting weights.
Learn how to perform the exercise correctly before using heavy weight.
Correct form is important to avoid injury and to ensure that you work the proper
muscle groups.
Know your limitations. If you are new to weight training or are embarking on
an exercise regimen after a long layoff, start slowly and build foundational
strength over a longer period of time.
Pay attention to your breathing. Exhale when you exert is a general rule of
thumb. Never hold your breath.
Enjoy your V-PREMIER HOIST® Fitness System!
PAGE 69
V-PREMIER ASSEMBLY
OWNER'S MANUAL
***THIS PAGE WAS INTENTIONALLY LEFT BLANK***
V-PREMIER ASSEMBLY
PAGE 70
OWNER'S MANUAL
Date
Exercise
Totals
S = Sets R = Repetition per set W = Weight used
WEIGHT TRAINING EXERCISE LOG
S R W S R W S R W S R W S R W S R W S R W S R W S R W S R W S R W S R W
V-PREMIER ASSEMBLY
PAGE 71
OWNER'S MANUAL
HOIST FITNESS SYSTEMS
LIMITED LIFETIME WARRANTY
Hoist Fitness Systems warrants this product to the original purchaser to be free from defects in workmanship and/or
materials under normal use or service. If at any time a component part is defective, Hoist Fitness Systems shall repair or
replace it (at Hoist Fitness Systems option) within a reasonable period of time. This warranty does not cover costs of removal.
transportation or reinstallation. This warranty shall not apply if the defect was caused by misuse, neglect or normal wear and
tear.
WARRANTY CLAIMS. All claims require: Model number, Serial
number, Date of installation, and any information supporting the
existence of the alleged defect.
To complete Warranty Registration visit:
www.HOISTFITNESS.com
and click on the Warranty Registration link
Starting from the original date of purchase, normal wear and tear shall be considered as the following:
COMMERCIAL USE: All malfunctions of upholstery, grips, paint, and chrome that occur after one year; all malfunctions of
electronic components, belts, or cables after one year; all malfunctions of pulleys, bearings, or bushings that occur after five
years. The frame and all welded components are warranted for the life of the product.
HOME USE: All malfunctions of grips, paint, and chrome that occur after ten years; all malfunctions of electronic
components, belts, cables, or upholstery that occur after ten years; all malfunctions of pulleys, bearings, or bushings that
occur after ten years. The frame and all welded components are warranted for the life of the product.
PLEASE NOTE THAT NOT ALL HOIST PRODUCTS ARE MADE FOR COMMERCIAL USE.
Refer to the instructions page of your owners manual or consult with you fitness product dealer to establish if a product is
made for commercial use or not. Using a non-commercial product in a commercial setting can result in serious injury or
death!
Hoist Fitness Systems sole responsibility shall be to repair or replace the component within the terms stated above. Hoist
Fitness Systems shall not be liable for any loss or damage of any kind including any incidental or consequential damages
resulting, directly or indirectly from any warranty expressed or implied or any other failure of this product.
WHAT IS NOT COVERED BY THIS WARRANTY
Hoist's sole obligation under this warranty is limited to either repair or replacement of parts, subject to the additions below.
This warranty neither assumes nor authorizes any person to assume obligations other than expressly covered by this
warranty.
NO CONSEQUENTIAL DAMAGES. Hoist is not responsible for economic loss; profit loss; or special, indirect, or
consequential damages.
WARRANTY IS NOT TRANSFERABLE. This warranty is not assignable and applies only in favor of the original
purchaser/user to whom delivered. Any such assignment or transfer shall void the warranties herein made and shall void all
warranties, expressed, implied or statutory, except the one (1) and five (5) year warranties described above. These
warranties are exclusive and in lieu of all other warranties, including implied warranty and merchantability or fitness for a
particular purpose. There are no warranties which extend beyond the description on the face hereof.
TRANSPORTATION COSTS. Hoist will accept parts covered under this warranty freight collect, provided that shipment
has received prior approval. Hoist is not responsible for any other transportation costs, but will ship freight collect parts either
repaired or replaced under these warranties.
Hoist Fitness Systems
9990 Empire St. #130
San Diego, CA. 92126
(800)548-5438
PLEASE KEEP THIS FOR YOUR RECORDS
V-PREMIER ASSEMBLY
PAGE 72
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising