Yamaha | DTX482K | Owner's Manual | Yamaha DTX482K Owner's Manual

Yamaha DTX482K Owner's Manual
2.
Manual Development Group
© 2018 Yamaha Corporation
Published 08/2014 POMA*.*-**A0
ELECTRONIC DRUM KIT
DTX482K
Owner’s Manual EN
Assembly Guide (1/2)
To assemble the DTX482K, refer to this Owner’s Manual and the DTX402K, DTX432K, and DTX452K Owner’s Manual
VAU5550
Fully Assembled DTX482K
Thank you for purchasing the Yamaha DTX482K! As a high-end model of the DTX402 series, the DTX482K comes standard
with three cymbal pads (two crashes and one ride) and the DTX-series XP80 Snare Pad. We recommend that you read this
manual carefully so that you can fully take advantage of the advanced and convenient functions of the instrument. We also
recommend that you keep this manual in a safe and handy place for future reference.
Step 10
Step 9
Step 8
Step 5
Step 9
Before using this product, be sure to read the “PRECAUTIONS” on pages 4 to 5 on the DTX402K, DTX432K, and DTX452K Owner’s Manual.
Step 7
NOTICE
Additional cymbal pad
Step 6
Some objects made of rubber and similar materials can easily stain the drumhead of the snare pad. Do not leave such objects in contact with the drumhead for a long period of
time. Pay special attention to avoid stacking the pads when putting them in storage, for example.
Cable band position
1.
Package Content
CAUTION
Step 4
• Choose a flat, hard surface on which to
assemble your electronic drum kit.
After opening up the package containing your electronic drum kit, please verify that all of the following parts are present.
Step 2
Step 1
DTX482K Package Content
Rack (Large)
• Take care to avoid mixing up parts or assembling them in the wrong direction. In addition,
the assembly steps should be completed one
at a time in the order described.
Step 3
Rod for the snare pad
Hi-hat holder
Cymbal holders (×2)
• The assistance of at least one other person
will be required when assembling the electronic drum kit.
Rack (Small)
No Stopper
Stopper
Step 12
• Once a piece has been assembled, be sure to
tighten the corresponding key bolts.
Drum module
Step 11
Pipe for
TOM3
1.
Crash cymbal pad
3.
Slide the holder clamp onto the TOM3 pipe, and lightly tighten the
clamp bolt of the cymbal holder.
Loosen the (1, 2) key bolts and detach the pipe for TOM3.
w
Cymbal/hi-hat pads (×2)
Step 12
 Attaching the cymbal holder for the additional cymbal pad.
KP65
Kick pad
• To disassemble your electronic drum kit, carry
out the assembly sequence in reverse.
Pipe for TOM3
HH65 Hi-hat controller
FP6110A
Foot pedal
Holder clamp
r
2
Clamp bolt
Sensor (bumps)
e
Nine-channel snake cable
Drum key
Cable bands (×3)
4.
AC adaptor
* May not be included depending on your particular area.
Please check you’re your Yamaha dealer.
q
DTX482K Owner’s Manual (this booklet)
DTX402K, DTX432K, and DTX452K Owner’s Manual
KP65 Owner’s Manual
XP70, XP80 Owner’s Manual
Additional Cymbal pad
Cymbal holder (×1)
Stopper (×1)
2.
1
Pipe for TOM3
Loosen the clamp bolt of the cymbal holder.
XP80 Snare Pad
5.
Cymbal pad (×1)
Attach the TOM3 pipe back to the large rack.
XP80 main unit (×1)
Clamp bolt (×1)
Clamp bolt
Stereo audio cable (×1)
Tighten the key bolt ( in the above figure) on the large rack and the
clamp bolt of the cymbal holder.
Step 1
Cymbal holder
Step 2
Step 3
Turn the entire large rack over and continue with the
assembly by following the instructions on pages 13 and 14
of the DTX402K, DTX432K, and DTX452K Owner’s
Manual
Continue to the other side.
1
2.
Step 4
1.
3.
Assembly Guide (2/2)
8.
 Attaching an additional cymbal pad
Attaching the XP80 Snare Pad
Attach the rod for the snare pad to the small rack, and then tighten the
key bolt () by using a tuning key to secure the rod.
Rod for the snare pad
Attaching an additional cymbal pad requires a stopper. By properly attaching
the stopper prevents the cymbal pad from spinning during your performance
and protects cables from damage.
1.
Pass the end of the cymbal holder shaft through the large hole at the center of the cymbal pad, and the stopper pin through the small hole in the
cymbal pad (fig. 6).
NOTE
If the stopper pin does not reach the small hole in the cymbal pad, the stopper
will not hold the cymbal pad properly. Make sure to secure the stopper position
as shown in Step 6.
Rotate the cymbal holder upward and tighten the clamp bolt, and then
bring the cymbal tilter upward (fig. 1).
9. Place the other felt pad on the cymbal holder (fig. 6).
10. Screw the wing nut to secure the pad to the cymbal holder (fig. 6).
Cymbal holder
Setting up the drum module
Before you start using the drum module, power it up while
simultaneously pressing number button [8]. Doing this optimizes the settings on your drum module for the DTX482K.
Once the setup for the DTX482K is complete, there is no
need to perform this procedure every time you turn on the
drum module.
1.
While holding down the number button [8], press [
(Standby/On) button.
]
Wing nut
cymbal
tilter
2.
Felt pad
Lightly screw the clamp bolt into the socket on the snare pad. (Rotate the
clamp bolt five to six times.)
Stopper
Cup
Pad
Clamp bolt
3.
XP80 Snare Pad
Hold
Cup
Pad
Smaller hole
The number button [8] flashes while the settings on the drum
module are updated.
(fig. 1)
2.
3.
Loosen the key bolt on the stopper with a tuning key (fig. 2).
4.
Slide the stopper onto the cymbal holder’s shaft (fig. 4).
Bolt cover
Remove the wing nut, two felt pads, and the bolt cover from the cymbal
holder (fig. 3).
Pin
Cymbal holder
Stopper
NOTE
Attach the XP80 Snare Pad to the rod, and then tighten the clamp bolt to
secure the snare pad.
Rod for the snare pad
Felt pad
If the key bolt was not sufficiently loosened in Step 2, it may not be possible to
slide the stopper onto the cymbal holder’s shaft. If this occurs, loosen the key
bolt as much as possible without removing it.
5.
(fig. 6)
NOTICE
Screw down the bolt cover to secure it into position (fig. 4).
Step 11
Step 12
Step 13
Stopper
XP80 Snare Pad
Key bolt
Step 14
Follow the instructions on pages 18 to 20 on the DTX402K,
DTX432K, and DTX452K Owner’s Manual. For Step 12
and Step 14 , refer to the example for DTX452K.
Using the cable bands, secure the cables to the kit rack at the
positions.
Clamp bolt
CAUTION
Tuning key
Leave a gap of about a half inch between the base of the rod and the
snare pad.
1
 Connecting an additional cymbal
(fig. 2)
Bolt cover
Wing nut
1.
Connect the L-shaped plug of the stereo phone cable into the [OUTPUT]
jack of the cymbal pad.
2.
Connect the other plug to the [PAD > IN] jack on the KP65 kick pad.
Felt pads
Cymbal pad
Stopper
Bolt cover
2
KP65 Kick pad
Cymbal holder
Cymbal holder
4.
Adjust the angle of the snare pad by first loosening the key bolt (1 and
2 in the above figure). Tighten the key bolt securely after the adjustment.
Stereo phone
cable
(fig. 3)
6.
Step 5
Step 6
Step 7
Step 8
Follow the instructions on pages 15 to 17 on the DTX402K,
DTX432K, and DTX452K Owner’s Manual. With Step 5 ,
refer to the example for the DTX452K.
Place the stopper to make full contact with the bottom surface of the
bolt cover and tighten the key bolt
with a tuning key to secure the stopper (fig. 5).
(fig. 4)
Bolt cover
Full contact
Stopper
Step 9
Step 10
(fig. 5)
7.
This completes the setup.
Place one of the felt pads removed at Step 3 to the cymbal holder (fig. 6).
2
Initializing the drum module erases the settings for the DTX482K. After
initializing the drum module, make the initial settings for the DTX482K
by carrying out the procedure shown above.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising