Yamaha | ATS-2090 | Owner's Manual | Yamaha ATS-2090 Owner's Manual

Yamaha ATS-2090 Owner's Manual
Front Surround System
Owner’s Manual
• Read the supplied booklet “Safety Brochure” before using the unit.
EN
CONTENTS
INTRODUCTION
4
BEFORE USING THE UNIT
6
5
Connecting to a network.. .............................. 20
Network functions................................................................................................ 20
Wired network connections................................................................................. 21
Wireless network connections.. .......................................................................... 21
Connecting to a network with the Sound Bar Controller app.. ......................... 22
Features............................................................. 6
Accessories......................................................... 9
PLAYBACK
Using the remote control...................................... 9
Basic operations.. .............................................. 23
Part names and functions.................................... 11
23
Basic procedure for playback.............................................................................. 23
Operating the unit using voice commands (Amazon Alexa).. ............................ 25
PREPARATION
1
2
3
4
17
Enjoying your favorite sound............................... 28
Playback with 3D surround sound/surround sound.. ........................................ 28
Installation.. ................................................ 17
Selecting a surround mode.. ............................................................................... 28
Installing the unit.. .............................................................................................. 17
Playback with 2-channel stereo sound............................................................... 28
Connecting a TV.. .......................................... 18
Playback of human voices clearly (Clear Voice).. ............................................... 29
Connecting a TV that supports Audio Return Channel (ARC)............................ 18
Enjoying enhanced bass sound (Bass Extension)............................................... 29
Connecting a TV that does not support Audio Return Channel (ARC).............. 19
Using a Bluetooth® device.. ................................. 30
Connecting AV devices.. ................................. 19
Listening to audio from a Bluetooth® device...................................................... 30
HDMI connection with an AV device................................................................... 19
Useful features for playback................................ 32
Connecting to power...................................... 20
Using a TV’s remote control to operate the unit (HDMI control).. ..................... 32
Showing audio information and function settings.. .......................................... 33
Connecting to power........................................................................................... 20
2
En
Playing audio content using the Sound Bar
Controller app.. ................................................. 34
When any problem occurs (Network trouble).. ....... 52
Specifications.................................................... 54
Streaming services.. ............................................................................................ 34
Center unit specifications.................................................................................... 54
Playing audio content on your mobile device.. ................................................. 34
Subwoofer specifications.. .................................................................................. 56
CONFIGURATIONS
Supported HDMI audio and video formats.. ....................................................... 57
35
Supported digital audio formats......................................................................... 58
Information for qualified contractors or dealers..... 59
Configuring various functions.............................. 35
Mounting the center unit on a wall.. ................................................................... 59
Changing the brightness of the indicators (Dimmer).. ...................................... 35
Configuring the HDMI control function.. ............................................................ 36
Configuring HDMI audio output.. ....................................................................... 37
Setting the auto power standby function.. ........................................................ 38
Enabling/disabling touch panel control (Child Lock function)......................... 39
Enabling/disabling the network standby function............................................ 40
Enabling/disabling the wireless (Wi-Fi) function............................................... 41
Enabling/disabling the Bluetooth function.. ..................................................... 41
Updating the unit’s firmware.. ........................................................................... 42
Pairing the center unit and subwoofer manually.............................................. 42
Selecting the HDMI signal format....................................................................... 43
Initializing the unit.. ............................................................................................ 44
Setting the dynamic range compression.. ......................................................... 44
APPENDIX
46
When any problem occurs (General)...................... 46
When any problem occurs (Power and system
function)........................................................... 46
When any problem occurs (Audio)......................... 49
When any problem occurs (Bluetooth®)................. 51
3
En
INTRODUCTION
Information
Indicates notes on instructions, restrictions on functions, and additional
information that may be helpful.
About functions included in the unit
Amazon, Alexa, Amazon Music, Kindle and all related logos are trademarks of
Amazon.com, Inc. or its affiliates.
The services that can be used with this unit that are provided by third
parties may be changed, suspended, or ended without notice. Please be
aware that Yamaha Corporation does not bear any responsibility for
these services.
App StoreSM
Trademarks
The terms HDMI, the HDMI Logo, and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC in the United States
and other countries.
App Store is a service mark of Apple Inc.
x.v.Color™
Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, Pro
Logic, and the double-D symbol are trademarks of Dolby Laboratories.
“x.v.Color” is a trademark of Sony Corporation.
Android™
Google Play™
Android and Google Play are trademarks of Google LLC.
For DTS patents, see http://patents.dts.com.
Manufactured under license from DTS, Inc. DTS, the Symbol, DTS and the Symbol
together, DTS Digital Surround, and DTS Virtual:X are registered trademarks or
trademarks of DTS, Inc. in the United States and/or other countries.
The Wi-Fi CERTIFIED™ Logo is a certification mark of Wi-Fi Alliance®.
© DTS, Inc. All Rights Reserved.
Wi-Fi and Wi-Fi CERTIFIED are registered trademarks of Wi-Fi Alliance®.
4
En
• This manual uses the following signal words for the important
information:
–
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Yamaha Corporation is under
license.
WARNING
This content indicates “risk of serious injury or death.”
CAUTION
This content indicates “risk of injury.”
– n NOTICE
Indicates points that you must observe in order to prevent product
failure, damage or malfunction and data loss, as well as to protect
the environment.
– n NOTE
Indicates notes on instructions, restrictions on functions, and
additional information that may be helpful.
–
Spotify and Spotify logo are registered trademarks of the Spotify Group.
The Spotify Software is subject to third party licenses found here:
www.spotify.com/connect/third-party-licenses
Blu-ray™
“Blu-ray Disc™”, “Blu-ray™”, and the logos are trademarks of the Blu-ray Disc
Association.
• The illustrations and screens in this manual are for instructional
purposes only.
About content in this manual
• The company names and product names in this manual are the
trademarks or registered trademarks of their respective companies.
• This manual is for the following readers:
– the users of the unit
– the constructor, builder and dealer that mount the unit on the wall
• Software may be revised and updated without prior notice.
• In this manual, iOS and Android mobile devices are collectively
referred to as “mobile devices”. The specific type of mobile device is
noted in explanations as needed.
5
En
BEFORE USING THE UNIT
Features
Introduction
This unit is a front surround system that allows for the enjoyment of superior sound quality from video played on a TV connected to the unit.
n Play surround sound
n Ask Alexa to control the unit
Alexa, turn up the volume.
Alexa, switch the input source to HDMI.
Audio from a TV, media
streaming service, or BD/
DVD player can be played
with 3D surround sound/
surround sound.
With Alexa built-in, you can
operate this unit, access
your music playlists.
Alexa may not be available in your region.
View the Yamaha product website for
details.
6
En
n Easy operation using the smartphone app
n Listen to audio from Bluetooth devices and streaming
services
Streaming services
Bluetooth devices
Sound Bar Controller
Install the Sound Bar
Controller app on
either a smartphone
or tablet. Various
features and settings
can be easily accessed
and controlled via the
app.
Enjoy listening to audio
from Bluetooth devices
and streaming services*
such as Amazon Music and
Spotify.
* A subscription may be required to listen
to streaming services via this unit.
7
En
3D surround playback
HDMI control function
This unit supports virtual 3D surround sound technology called “DTS
Virtual:X”. Surround sound can be heard not only from horizontal
directions, but also from varying heights when this unit’s 3D surround
mode is enabled, creating a virtual acoustic environment. This ultimately
provides an immersive audio and sound experience by creating a sense
of sounds not only coming from behind, but also above the listener. For
details, see the following:
Link functions of a TV and the unit are available using the TV’s remote
control. When a TV that supports Audio Return Channel (ARC) is used,
this ARC-compatible unit can be connected to the TV via a single HDMI
cable. For details, see the following:
• “Using a TV’s remote control to operate the unit (HDMI
control)” (p.32)
• “Connecting a TV that supports Audio Return Channel (ARC)” (p.18)
• “Playback with 3D surround sound/surround sound” (p.28)
Bass Extension
Wireless subwoofer
The bass extension feature boosts bass levels for more impactful sound.
For details, see the following:
The supplied wireless subwoofer enables more dynamic audio playback.
• “Enjoying enhanced bass sound (Bass Extension)” (p.29)
Transmission of 4K high dynamic range
(HDR) video
Clear Voice
The clear voice function makes speech, such as dialog and narration,
clearer. For details, see the following:
Enjoy 4K High Dynamic Range (HDR) content from HDR-compatible
sources such as a TV, media streaming device, gaming console, or set-top
box. For details, see the following:
• “Playback of human voices clearly (Clear Voice)” (p.29)
• “Supported HDMI audio and video formats” (p.57)
8
En
Accessories
Using the remote control
Checking the accessories
Preparing the remote control
Make sure you have received all of the following accessories.
Remove the battery insulating strip before attempting to use the remote
control.
The unit (ATS-CU2090)
In this manual, the unit may also be
referred to as the “center unit”.
Remote control
A CR2025 Lithium battery
has already been inserted
into the remote control.
Wireless subwoofer
(NS-WSW44)
In this manual, the wireless subwoofer
is referred to as the “subwoofer”.
Battery insulating strip
Operating range of the remote control
Power cord x 2
Operate the remote control within the range shown in the following
figure.
Optical digital audio cable
Mounting template
Use when mounting the center unit on a wall.
Within 6 m (20 ft)
Remote control
sensor
Quick Start Guide
Safety Brochure
9
En
Press and hold ▽ on the rear cover of the remote control, slide the cover
out in the direction indicated [1], and replace the old battery with a new
one [2]. Slide the rear cover back into place in the direction indicated
[3].
Replacing the battery in the remote
control
[1]
WARNING
• DO NOT SWALLOW THE BATTERY.
• Keep new and used batteries away from children.
• If the battery compartment does not close securely, stop using the product and
keep it away from children.
Rear cover
The remote control supplied with this product contains a coin/button cell battery.
If the coin/button cell battery is swallowed, it can cause severe internal burns in
just two hours and can eventually lead to death. If you think a battery might have
been swallowed or placed inside any part of the body, seek immediate medical
attention.
CAUTION
• Do not put in a pocket or bag, carry, or store batteries together with pieces of
metal.
The battery could short, burst, or leak, causing a fire or injury.
• When storing or discarding batteries, insulate the terminal area by applying tape, or
some other protection.
Mixing them with other batteries or metal objects can cause a fire, burns, or
inflammation due to fluid.
[2]
CR2025 Lithium battery
025
2
CR
+
[3]
10
En
Part names and functions
Part names and functions of the front/top panel
The part names and functions of the front and top panels are as follows.
a
b
c
d
e
f
g
h
i
h
a Indicators
The indicators on the top panel flash or glow to
show the operation and setting status. In this
manual, indicator status, such as off, glowing,
and flashing, are shown as the illustrations
below.
Off
Glows
Flashes
e } / { (volume +/-)
b ) (Alexa)
Manually wake Alexa to enable a voice
command (p.25).
c ) (Microphones disabled)
Touch to disable the microphones. Alexa will
not respond to utterances while the
microphones are disabled. Disable the
microphones to maintain privacy. Touch again
to enable the microphones (p.25).
d y (input)
Select an input source (p.23).
Adjust the volume (p.23).
f z (power)
Turn on or off the unit.
g Microphones
Used to interact with Alexa.
n NOTICE
• Do not use a vacuum cleaner or aerosol air duster
on the microphones when cleaning the unit. Doing
so may damage the microphones.
h Speakers
11
En
i Remote control sensor
Receives infrared (IR) signals from the remote
control of the unit (p.9).
n NOTE
• b, c, d, e and f are touch sensors. Touch icons
with your finger to control functions.
• Do not place any objects on the touch panel as doing
so may result in unintended operations.
• When touch panel control is disabled, no operations
can be performed using the unit’s touch panel. This
prevents accidental operation of the unit. For details,
see the following:
– “Enabling/disabling touch panel control (Child Lock
function)” (p.39)
• The brightness of the indicators can be changed using
MUSIC on the remote control. For details, see the
following:
– “Changing the brightness of the indicators
(Dimmer)” (p.35)
12
En
Part names and functions of the rear panel
The part names and functions of the rear panel are as follows.
d e f
a
b
a Power connector
Connect the power cord (p.20).
b HDMI IN jack
For connecting to an HDMI-compatible AV
device, such as a BD/DVD player, a satellite and
cable TV tuner, and a game console, and
inputting video/audio signals (p.19).
c
f UPDATE ONLY jack
c HDMI OUT (ARC) jack
For connecting to an HDMI-compatible TV and
outputting video/audio signals (p.18). When a
TV that supports Audio Return Channel (ARC) is
used, TV audio signals can also be input through
this jack.
d NETWORK jack
For connecting to an ethernet cable (sold
separately) (p.21).
e TV input jack
For connecting to a TV that does not support
ARC. This jack cannot be used when the unit is
connected to an ARC-compatible TV (p.19).
13
En
Use to update this unit’s firmware, if necessary.
The jack is located inside the cover.
Refer to the instructions supplied with the
firmware for details.
Part names and functions of the subwoofer
The part names and functions of the subwoofer are as follows.
Front panel
Rear panel
b
a
e
a Bass reflex port
b PAIRING button
Use to pair the center unit with the subwoofer
manually (p.42).
c STANDBY indicator
d * indicator
Glows when the center unit and subwoofer are
connected wirelessly.
e Power connector
Connect the power cord (p.20).
Shows subwoofer’s status (p.15).
14
En
c
d
Part names and functions of the remote control
The part names and functions of the supplied remote control are as follows.
g | (mute) button
a @ (Alexa) button
a
z
HDMI
TV
BLUETOOTH
h
NET
Manually wake Alexa to enable a voice
command (p.25).
Mute the audio output (p.23). Press the button
again to unmute or press VOLUME (+/-).
h z (power) button
b Input buttons
b
Select an input source to be played back.
Turn on/off the unit.
c
• HDMI : Sound from a device connected to the
HDMI IN jack (p.19)
Center unit
CLEAR VOICE
3D SURROUND
i
• TV : TV audio (p.18)
d
MOVIE
TV
MUSIC
SPORTS
GAME
STEREO
j
e
• NET : Audio from streaming services (p.34)
c CLEAR VOICE button
BASS
EXT
f
k
INFO
SUBWOOFER
Off
Turned off/network standby(p.40)
Glows (red)
Enable/disable the clear voice function (p.29).
|
g
Turned on
• BLUETOOTH : Sound from a Bluetooth device
(p.30)
VOLUME
l
d Surround mode buttons
Select a surround mode for 3D surround or
surround playback according to your individual
preference (p.28).
• MOVIE
Turned off/Voice Control Ready (p.25)
Glows (white)
Subwoofer
• TV
Turned on
• MUSIC
Off
• SPORTS
• GAME
Glows (green)
e BASS EXT button
Enable/disable the bass extension function
(p.29).
f SUBWOOFER (+/-) button
Adjust the volume of the subwoofer (p.23).
15
En
Turned off/network standby (p.40)
Glows (red)
i 3D SURROUND button
Switch between 3D surround playback and
surround playback each time the button is
pressed (p.28).
j STEREO button
Switch to stereo (2-channel) playback (p.28).
k VOLUME (+/-) button
Adjust the volume of the unit (p.23).
l INFO button
Confirm the type of audio signal being played,
as well as settings for functions (p.33).
16
En
PREPARATION
1 Installation
Installing the unit
n NOTICE
• Do not stack the center unit and any other device directly on each other. Doing so
may cause a malfunction due to vibrations.
• Do not apply excessive force to the unit when moving it. Doing so may damage the
speakers or the portion covered with fabric.
• Avoid the following when installing the subwoofer to prevent any loss in sound
volume.
– Installing the subwoofer so that the speaker (portion covered with fabric) is too
close to a wall.
– Covering the subwoofer’s bass reflex port.
• The subwoofer can only be used in its upright position. Do not position the
subwoofer on its side.
• The unit contains non-magnetic shielding speakers. Do not place magnetically
sensitive items (hard disk drive, etc.) near the unit.
• Do not place objects such as metallic furniture between the center unit and the
subwoofer as such objects may interfere with wireless communication.
Install the unit as shown in the following illustration.
Install the subwoofer externally of the center unit. To prevent sound
from reflecting off of walls, angle the subwoofer slightly toward the
center of the room.
n NOTE
The center unit can also be mounted on a wall. For details, see the following:
• “Mounting the center unit on a wall” (p.59)
Touch panel
17
En
2 Connecting a TV
Connecting a TV that supports Audio
Return Channel (ARC)
n What is Audio Return Channel (ARC)?
In order for the unit to play audio from a TV, the TV must usually be connected to the
unit via an audio cable as well as an HDMI cable. If, however, the TV supports Audio
Return Channel (ARC), TV audio signals can be input to the unit via the HDMI cable that
outputs video signals from the unit to the TV.
Connect the TV, which supports Audio Return Channel (ARC), to the unit
with an HDMI cable (sold separately).
n NOTE
HDMI OUT (ARC) jack
• Connect an HDMI cable to the audio return channel supported jack (the jack with
“ARC” indicated) on TV.
• Enable the HDMI control function of the unit to activate the Audio Return Channel
(ARC). For details, see the following:
– “Configuring the HDMI control function” (p.36)
• Use a 19-pin HDMI cable with the HDMI logo printed on it.
• Keep the cable as short as possible to prevent any degradation in signal quality.
• Use a premium high-speed HDMI cable for playback of 3D and 4K video content.
• The TV input jack cannot be used when a TV that supports the Audio Return Channel is
connected to the unit.
HDMI input jack
HDMI
HDMI
(ARC)
HDMI
Center unit (rear)
TV
18
En
Connecting a TV that does not support
Audio Return Channel (ARC)
3 Connecting AV devices
HDMI connection with an AV device
Connect the TV to the unit with an HDMI cable (sold separately) and an
optical digital audio cable (supplied).
Connect an AV device such as a media streaming device to the unit with
an HDMI cable (sold separately).
HDMI OUT (ARC) jack
HDMI IN jack
HDMI input jack
HDMI
HDMI output jack
HDMI
HDMI
HDMI
HDMI
HDMI
Center unit
(rear)
OPTICAL
O
TV jack
1. Remove the cap.
Center unit (rear)
TV
AV device
O
n NOTE
Audio output jack
(digital optical)
• Once the HDMI control function has been activated, video and audio signals from AV
devices can be output from the TV even when the unit is turned off (HDMI signal passthrough). For details, see the following:
– “Configuring the HDMI control function” (p.36)
• Use a 19-pin HDMI cable with the HDMI logo printed on it.
• Keep the cable as short as possible to prevent any degradation in signal quality.
• Use a premium high-speed HDMI cable for playback of 3D and 4K video content.
2. Check the plug’s
orientation.
n NOTE
• Use a 19-pin HDMI cable with the HDMI logo printed on it.
• Keep the cable as short as possible to prevent any degradation in signal quality.
• Use a premium high-speed HDMI cable for playback of 3D and 4K video content.
19
En
4 Connecting to power
5 Connecting to a network
Connecting to power
Network functions
Once all connections have been made, connect the unit to power as
shown in the following illustration.
A network connection allows you to play various streaming services via
the unit, and to talk with Amazon Alexa to operate this unit, or to play
music.
The Sound Bar Controller app for mobile devices is required to configure
and operate network functions.
Power cord (supplied)
To an AC wall outlet
n NOTICE
• Do not connect this product to public Wi-Fi or Internet directly. Only connect this
product to the Internet through a router with strong password-protections. Consult
your router manufacturer for information on security best practices.
Rear
Once all connections have been made, connect the subwoofer to power
as shown in the following illustration.
n NOTE
• To use network function, the unit and mobile device must be connected to the same
router.
• When using a multiple SSID router, access to the unit might be restricted depending on
the SSID to connect. Connect the unit and mobile device to the same SSID.
• Some security software installed on your computer, or network device settings (such
as a firewall), may block the unit’s access to streaming services. Should this occur,
change security software and/or network device settings.
• A network connection cannot be established if the MAC address filter on your router is
enabled. Check your router’s settings.
• To configure your router’s subnet mask manually, apply the same subnet used by this
unit to all devices.
• Use of a broadband connection is recommended when using Internet services.
• The unit cannot be connected to a network that requires manual setup. Connect the
unit to a DHCP enabled router.
Rear
Power cord (supplied)
To an AC wall outlet
20
En
Wired network connections
Wireless network connections
To use a wired network connection, connect the unit to a router via an
STP ethernet cable (CAT-5 or higher straight cable).
Connect the unit to a wireless router (access point) to use a network.
See the following for instructions on connecting to a wireless router
(access point).
Internet
• “Connecting to a network with the Sound Bar Controller app” (p.22)
Internet
WAN
Wireless router
(access point)
LAN
Modem
Modem
Router
STP ethernet cable
(sold separately)
NETWORK jack
Mobile device
Mobile device
n NOTE
• If the unit and the wireless router (access point) are too far apart, the unit may not
connect to a wireless router (access point). In such case, place them close to each
other.
• This unit operates only in the 2.4-GHz band. Connect your mobile device to the
network using the 2.4-GHz band and then configure the unit’s settings for a wireless
connection.
21
En
Connecting to a network with the Sound
Bar Controller app
2
Follow the app’s on-screen instructions to complete
the settings.
Install the Sound Bar Controller app on your mobile device to connect
the unit to a network.
n NOTE
• Confirm that your mobile device is connected to your home router before beginning.
• Screen displays are provided for reference purposes only. Actual screen displays may
differ depending upon the mobile device used.
• Sound Bar Controller app screens and menu labels are subject to change without prior
notice.
1
Install the Sound Bar Controller app on your mobile
device, and then open the app.
Search for “Sound Bar Controller” on the App Store or
Google Play.
The * indicator on the unit glows when the unit is connected to a
wireless network.
Glows (White)
n NOTE
When the unit is connected to a network for the first time after purchase, the unit’s
firmware is updated to the latest firmware version.
22
En
PLAYBACK
Basic operations
Basic procedure for playback
1
Basic procedure for playing back music is as follows.
z
z
HDMI
TV
BLUETOOTH
CLEAR VOICE
HDMI
TV
BLUETOOTH
The center unit and subwoofer are automatically connected
via wireless connection. Once the connection has been
successfully established, the * indicator on the subwoofer’s
rear panel glows, and the unit is ready for playback.
z (power)
2
NET
NET
Input buttons
3D SURROUND
CLEAR VOICE
MOVIE
TV
MUSIC
SPORTS
GAME
STEREO
SPORTS
3D SURROUND
GAME
STEREO
BASS
EXT
SUBWOOFER (+/-)
BASS
EXT
INFO
|
SUBWOOFER
VOLUME
VOLUME (+/-)
INFO
|
SUBWOOFER
Press z to turn on the unit.
VOLUME
| (mute)
23
En
Turn on the external devices (such as a TV, BD/DVD
player, and gaming console) connected to the unit.
3
5
Use the input buttons to directly select an input
source to be played.
Press VOLUME (+/-) to adjust the volume.
The number of glowing indicators (other than the Alexa
indicator) increases or decreases as volume is raised or
lowered.
HDMI: Sound from a device connected to the HDMI IN jack
TV: TV audio
BLUETOOTH: Sound from a Bluetooth device
NET: Audio from streaming services
Volume down (-)
The indicator for the selected input source glows.
Volume up (+)
When audio is output from both TV speaker and the unit,
mute the TV sound.
Example
When TV is selected
TV
6
n NOTE
Glows
4
Adjust sound settings to suit individual preferences.
Start playback on the external device selected in step
3.
24
• If the * indicator on the subwoofer does not glow properly the first time the unit is
turned on, pair the center unit and subwoofer manually. For details, see the following:
– “Pairing the center unit and subwoofer manually” (p.42)
• For details on adjusting sound settings, see the following:
– “Playback with 3D surround sound/surround sound” (p.28)
– “Playback with 2-channel stereo sound” (p.28)
– “Playback of human voices clearly (Clear Voice)” (p.29)
– “Enjoying enhanced bass sound (Bass Extension)” (p.29)
En
• For details on playing music files stored on a Bluetooth device, see the following:
– “Listening to audio from a Bluetooth® device” (p.30)
• For details on playing audio from streaming services, see the following:
– “Streaming services” (p.34)
• To mute the sound, press |. Press | again or VOLUME (+/-) to unmute.
Operating the unit using voice
commands (Amazon Alexa)
You can talk to Amazon Alexa on your unit. With Alexa, you can ask to
play music, hear the news, check weather, control smart home devices,
and more.
Flash (on mute)
• When sound input to the HDMI IN jack is output from the TV, the volume level does not
change even if you press VOLUME (+/-) or |.
• To adjust the subwoofer volume, press SUBWOOFER (+/-). The subwoofer volume can
be adjusted separately from the whole volume.
The indicator (other than the Alexa indicator) that glows changes as volume is raised or
lowered.
An Amazon account is required to use Amazon Alexa and the unit must
be connected to a network. Use the Sound Bar Controller app to enter
your Amazon account information and log into the service.
Alexa can perform the following operations with the proper voice
commands.
• Switching input sources
• Adjusting (muting) the volume
Volume down (-)
• Selecting and listening to streaming services
See the following website for details on the supported streaming
services:
https://manual.yamaha.com/av/sb/ss/sbc/
Volume up (+)
• When playing audio/video from a device connected to the TV, select TV as the unit’s
input source, and select the playback device with the input selector on the TV.
n NOTE
• As of August 2019, Amazon Alexa supports the following languages: English, German
and French.
• Service is limited to certain areas.
• Services supported by the unit may not be available in some regions in which the unit
is sold.
• See the product information page on the Yamaha website for the latest information.
• A subscription may be required to listen to Amazon Music or Amazon Kindle on this
unit. For more information, visit the Amazon website.
• For information on other streaming services, visit the websites of those service
providers.
• A smart hub (sold separately) may be required to connect smart home devices that will
be controlled via the unit.
25
En
For example, just ask:
n NOTE
l Adjust the volume
“Alexa, turn up the volume.”
“Alexa, turn down the volume.”
• Amazon Alexa is a service provided by Amazon. This service may change, be
discontinued, or be terminated without notice. Please note that Yamaha Corporation
is in no way responsible for the continuation of this service, and will not be held liable
for any issues that arise from the use of this service.
• This service is limited to certain areas.
• This service may not be available in some countries or regions.
• Some functions require a third party service agreement.
• To prevent accidental or mistaken response from Alexa, or to maintain privacy,
touch ) on this unit to disable the microphones.
• Alexa can be activated or summoned by calling out, “Alexa,” or by pressing @ on the
remote control or touching ) on the unit.
• When the Voice Control Ready function is enabled, Alexa can accept voice commands
even when the unit is turned off. Use the Sound Bar Controller app to enable or disable
the Voice Control Ready function.
• The dedicated Amazon Alexa app for mobile devices provided by Amazon allows you to
configure detailed settings and add functions. For details, see the Amazon Alexa app
help guide.
l Switch input sources
“Alexa, switch the input source to HDMI.”
l Listen to streaming content from Amazon Music
“Alexa, play some jazz music.”
l Operate playback
“Alexa, play next song.”
“Alexa, stop the music.”
“Alexa, what is this song?”
l Check the weather
“Alexa, what's the weather?”
l Set a timer
“Alexa, set a timer for 10 minutes.”
26
En
n Alexa indicator
Examples of
Alexa indicator activity
Status of Alexa
The Alexa indicator on this unit glows depending on the status of Alexa,
as follows.
The microphones are disabled.
Examples of
Alexa indicator activity
Status of Alexa
Glows red
Idle
A system setting is changed.
Goes off
Glows orange
Listening to a request
An error occurred.
Glows pale blue
Flashing red three times
Processing a request
Flashing blue
Responding
Flashing blue and pale blue slowly
Notifications such as timers, alarms, and
reminders
Flashing blue and pale blue quickly
A notification is received.
Flashing yellow
27
En
Enjoying your favorite sound
Playback with 3D surround sound/
surround sound
Selecting a surround mode
The unit switches between 3D surround playback and surround playback
each time 3D SURROUND is pressed. Select 3D surround playback or
surround playback according to the input source or your individual
preference.
Select the surround mode best suited to the content by pressing MOVIE,
TV, MUSIC, SPORTS, or GAME with 3D surround playback or surround
playback enabled.
When 3D surround playback is selected, DTS Virtual:X makes it possible
to hear sound not only from horizontal directions, but also from varying
heights.
3D surround playback
MOVIE
TV
SPORTS
GAME
MUSIC
Playback with 2-channel stereo sound
3D SURROUND
Press STEREO to switch to 2-channel stereo playback according to the
input source or your individual preference.
Glows (blue): 3D surround playback
When stereo playback is enabled, the SURROUND indicator goes off.
Surround playback
STEREO
3D SURROUND
Off
Glows (white): surround playback
28
En
Playback of human voices clearly (Clear
Voice)
Enjoying enhanced bass sound (Bass
Extension)
Press CLEAR VOICE to turn on the clear voice function. Human voices
such as dialogue in movies, TV shows, news, and sport commentary can
be heard clearly.
Press BASS EXT to turn on the bass extension function. You can enjoy
enhanced bass sound and more powerful sound.
Press the button again to disable the function.
Press the button again to disable the function. The indicators will go off.
BASS
EXT
Flash three times (enabled)
Flash once (disabled)
CLEAR VOICE
Glows
n NOTE
Press INFO to confirm whether the bass extension function is enabled or disabled. For
details, see the following:
• “Showing audio information and function settings” (p.33)
29
En
Using a Bluetooth® device
Listening to audio from a Bluetooth®
device
1
Press BLUETOOTH to select “Bluetooth” as the input
source.
The unit is ready for the Bluetooth connection, and the
BLUETOOTH indicator on the unit flashes.
Audio content from a Bluetooth device (such as a smartphone, tablet,
laptop, or digital music player) can be played through this unit over a
wireless connection.
BLUETOOTH
Flashes
Bluetooth devices
n NOTE
If Bluetooth devices have been connected before, the unit will connect to the
last connected device when BLUETOOTH is pressed.
2
On the Bluetooth device, enable the Bluetooth
function.
The Bluetooth device list appears on the Bluetooth device.
n NOTE
• Our exclusive Compressed Music Enhancer technology improves sound quality and
characteristics, and can be used to enjoy realistic and impressive sound.
• The network standby function is enabled by default. When a Bluetooth device is
connected to this unit while the unit is off, the unit will be turned on and will be
immediately ready to play sound from the Bluetooth device. For details, see the
following:
– “Enabling/disabling the network standby function” (p.40)
30
En
3
4
Select this unit in the list.
Play content with audio on the Bluetooth device.
The unit’s name is displayed as shown in the following
illustration.
The unit will begin playing audio from the Bluetooth device.
Yamaha ATS-2090
n NOTE
When the connection between the Bluetooth device and the
unit is established, a completion message is displayed on
the Bluetooth device, and the BLUETOOTH indicator on the
unit glows.
• To terminate the Bluetooth connection, perform one of the following operations.
– Turn off the Bluetooth function on the Bluetooth device.
– Hold down BLUETOOTH for at least five seconds.
– Select an input source other than Bluetooth on the unit.
– Turn off the unit.
• Adjust the volume level of the Bluetooth device as required.
• Perform Bluetooth connection with the Bluetooth device and unit within 10 m (33 ft) of
each other.
• See documentation supplied with your Bluetooth device for more information.
Glows
31
En
Useful features for playback
a
Using a TV’s remote control to operate
the unit (HDMI control)
Turn on/off
Both the TV and the unit turn on/off at the same time.
b
Switch input sources
The HDMI control function coordinates TV and unit operation so that the
unit can be operated using the TV’s remote control.
The unit's input source switches accordingly when the TV’s input source is
switched.
When the unit is connected to a TV via HDMI cable, the TV’s remote
control can be used to perform the following operations.
For example, when a TV program is selected on the TV, the unit’s audio input
source is switched to the HDMI OUT (ARC) jack using the ARC function or TV
input jack.
TV's remote control (example)
When a BD/DVD player is connected to the HDMI IN jack on the unit, the
unit’s input source switches to HDMI when the BD/DVD player is selected
with the TV’s remote control.
a
c
b
Switch the audio output device
The audio output device can be switched to the TV or this unit. Operations
may differ depending upon TVs.
d
Adjust volume
The unit’s volume can be adjusted when the TV’s audio output is set to the
unit.
n NOTE
• If you are unable to operate the unit with your TV’s remote control, configure the HDMI
control function of your TV and the unit. For details, see the following:
– “Configuring the HDMI control function” (p.36)
• The input source can be switched while the unit is off (HDMI signal pass-through).
• The volume displays on the TV and unit may not be the same.
c
d
32
En
Showing audio information and function
settings
c
The type of audio signal being played, as well as settings for functions
can be confirmed by the status of indicators.
d
1
Show the bass extension function setting.
Glows: Enabled
Off: Disabled
Show the Bluetooth function setting.
Glows: Enabled
Off: Disabled
Press INFO.
n NOTE
The Bluetooth function setting is not shown while audio content is playing from a
Bluetooth device or over a network.
The indicators on the unit will show the following audio
information for three seconds immediately after INFO is
pressed.
e
Show the dynamic range compression setting
Glows (blue): Compression (maximum)
INFO
Glows (white): Compression (standard)
Off: No compression
a
a
b c d e f g
f
Show the wireless (Wi-Fi) function setting.
Show the type of audio signal.
Glows: Enabled
STATUS glows (white): Dolby Digital
Off: Disabled
STATUS glows (red): DTS
g
STATUS and HDMI off: PCM/no input
Show touch panel control setting
Glows: Enabled
b
Show whether Dolby Pro Logic II is enabled or disabled.
Off: Disabled
Glows: Enabled
Off: Disabled
n NOTE
Dolby Pro Logic II is enabled automatically when 2-channel stereo signals are
played in surround sound.
33
En
Playing audio content using the Sound Bar Controller app
Streaming services
Audio content distributed by various streaming services over the Internet
can be played via the unit. Use the dedicated app for mobile devices
provided by a particular streaming service or talk to Amazon Alexa to
select content to play from a streaming service. See the product
information page on the Yamaha website for information on services
supported by the unit.
Playing audio content on your mobile
device
Play audio content on your mobile device over a network.
Use the Sound Bar Controller app installed on your mobile device to play
audio content. See the Sound Bar Controller app for details.
Mobile device
For additional information on the streaming services, see the following
website.
Router
https://manual.yamaha.com/av/sb/ss/sbc/
n NOTE
wired or wireless
• A subscription may be required to listen to streaming services via this unit. For
information on a particular streaming service, visit that service’s website.
• Service is limited to certain areas.
• Services supported by the unit may not be available in some regions in which the unit
is sold.
• Services may change or be discontinued without notice. Please note that Yamaha
Corporation is in no way responsible for, and will not be held liable for, streaming
services or issues arising from their use.
34
En
CONFIGURATIONS
Configuring various functions
Once the indicators have shown the brightness setting
applied to the unit as follows, the unit will turn on.
Changing the brightness of the
indicators (Dimmer)
• Dim (default setting)
Change the brightness of the indicators on the center unit.
The brightness is dim by default.
1
2
Turn off the unit.
Glow
• Off
Press and hold MUSIC for at least five seconds.
The brightness setting of the indicators is changed.
Glow
MUSIC
• Bright
Glow
Glow
Glow
n NOTE
Indicators glow brightly just after operation and change to the specified brightness after a
few seconds.
35
En
Configuring the HDMI control function
1
2
Enable or disable the unit’s HDMI control function (link function). This
function coordinates TV and unit operation so that the unit can be
operated using the TV’s remote control.
Turn off the unit.
Press and hold HDMI for at least five seconds.
The HDMI control function is enabled or disabled.
This function is enabled by default.
HDMI
Once the indicator has shown the HDMI control function
setting applied to the unit as follows, the unit will turn on.
Glows (enabled)
Off (disabled)
n NOTE
• Enable the HDMI control function when connecting a TV that supports Audio Return
Channel (ARC), or when using HDMI signal pass-through. For details, see the following:
– “Connecting a TV that supports Audio Return Channel (ARC)” (p.18)
– “HDMI connection with an AV device” (p.19)
• If the unit cannot be operated with the TV’s remote control, confirm that the HDMI
control function of this unit is enabled and the HDMI control function is enabled on the
TV. For details, see the following:
– “The unit cannot be operated using the TV’s remote control” (p.48)
• The unit’s power consumption will be reduced if the HDMI control function is disabled.
36
En
Configuring HDMI audio output
1
2
Select the device from which audio input via the unit’s HDMI IN jack will
be played when the HDMI control function is disabled. HDMI audio is
output from this unit by default.
The unit (default)
Play HDMI audio input signal from the unit.
TV
Play HDMI audio input signal from the TV.
Turn off the unit.
Press and hold 3D SURROUND for at least five
seconds.
The HDMI audio output setting is changed.
3D SURROUND
Once the indicator has shown the HDMI audio output setting
applied to the unit as follows, the unit will turn on.
Glows (audio is played from the unit)
Off (audio is played from the TV)
n NOTE
• When playing back HDMI audio input signal from the TV, the unit cannot be used to
adjust volume. Use TV controls to adjust volume.
• For details on the HDMI control function, see the following:
– “Configuring the HDMI control function” (p.36)
• To configure HDMI audio output with the HDMI control function enabled, select the
audio output device on the TV connected to the unit.
• HDMI video signals input to the HDMI IN jack of this unit are always output from the
HDMI OUT (ARC) jack of the unit.
37
En
Setting the auto power standby function
1
2
Enabling the auto power standby function prevents the unit from
remaining on when not in use. When the auto power standby function is
enabled, the unit automatically turns off in any of the following
situations.
Turn off the unit.
Touch and hold y and then touch and hold z on the
unit for at least five seconds.
The auto power standby function is enabled or disabled.
• No operations for 8 hours
• No audio input and no operations for 10 minutes
This function is enabled by default.
Once the indicator has shown the auto power standby
function setting applied to the unit as follows, the unit will
turn on.
Glows (disabled)
Off (enabled)
38
En
Enabling/disabling touch panel control
(Child Lock function)
1
2
Disable touch panel control to prevent children from accidentally
operating the unit.
Touch panel control is enabled by default.
Turn off the unit.
Press and hold INFO for at least five seconds.
The touch panel control is enabled or disabled.
INFO
Once the indicator has shown the touch panel control
setting applied to the unit as follows, the unit will turn on.
Glows (enabled)
Off (disabled)
n NOTE
Press INFO to confirm whether the child lock function is enabled or disabled. For details,
see the following:
• “Showing audio information and function settings” (p.33)
39
En
Enabling/disabling the network standby
function
1
2
Enabling the network standby function allows the unit to be turned on or
off using a mobile or Bluetooth device as follows.
This function is enabled by default.
Turn off the unit.
Press SPORTS for at least five seconds.
The network standby function is enabled or disabled.
• The unit can also be turned on and off using the Sound Bar Controller
app installed on your mobile device.
SPORTS
• When a Bluetooth device is connected to this unit while it is off, this
unit turns on and the input source switched to BLUETOOTH.
Once the indicator has shown the network standby function
setting applied to the unit as follows, the unit will turn on.
Glows (enabled)
Off (disabled)
n NOTE
The unit consumes more power when it is off with the network standby function enabled
than it does when it is off with this function disabled.
40
En
Enabling/disabling the wireless (Wi-Fi)
function
Enabling/disabling the Bluetooth
function
Enable or disable the wireless (Wi-Fi) function.
This function is enabled by default.
Enable or disable the Bluetooth function.
This function is enabled by default.
1
2
1
2
Turn off the unit.
Press and hold NET for at least five seconds.
Turn off the unit.
Press and hold BLUETOOTH for at least five seconds.
The wireless (Wi-Fi) function is enabled or disabled.
The Bluetooth function is enabled or disabled.
NET
BLUETOOTH
Once the indicator has shown the wireless (Wi-Fi) function
setting applied to the unit as follows, the unit will turn on.
Once the indicator has shown the Bluetooth function setting
applied to the unit as follows, the unit will turn on.
Glows (enabled)
Off (disabled)
Glows (enabled)
Off (disabled)
n NOTE
n NOTE
Press INFO to confirm whether the wireless (Wi-Fi) function is enabled or disabled. For
details, see the following:
• “Showing audio information and function settings” (p.33)
Press INFO to confirm whether the Bluetooth function is enabled or disabled. For details,
see the following:
• “Showing audio information and function settings” (p.33)
41
En
Updating the unit’s firmware
Pairing the center unit and subwoofer
manually
New firmware that provides additional features or product
improvements will be released as needed. Firmware can be updated
using the Sound Bar Controller app installed on a mobile device.
The center unit and subwoofer are automatically connected via wireless
connection the first time the unit is turned on. If the center unit and
subwoofer are not properly connected due to a temporary
communications failure, pair the center unit and subwoofer manually.
n NOTICE
• Do not operate the unit or disconnect the power cord or network cable during
firmware update.
• If the Internet connection speed is slow, or the unit is connected to the wireless
network, network update may not be possible depending on the condition of the
network connection. Should this occur, try again at a later time.
• For details on update, visit the Yamaha website.
n NOTE
Pairing is the process of having the center unit and subwoofer recognize one another as
connection destinations.
1
2
When a new firmware is released, a “NEW” icon is displayed on the
screen of the Sound Bar Controller app. Tap the icon, then follow the onscreen instructions to update the firmware.
Turn off the unit.
Press and hold SUBWOOFER (-) for at least five
seconds.
The center unit is turned on and the HDMI indicator flashes.
Flashes
SUBWOOFER
42
En
3
Within 30 seconds, press and hold the PAIRING button
on the rear panel of the subwoofer for at least five
seconds.
When the center unit and subwoofer have been paired
successfully, the * indicator will glow.
Selecting the HDMI signal format
Problems such as a lack of sound or the appearance of abnormal colors
in a video may occur when some AV devices are connected to the unit.
Should this occur, changing the setting may resolve these issues.
Mode 1 (default)
Select this mode in most cases.
Mode 2
Select this mode if problems such as the appearance of
abnormal colors in video have occurred.
1
2
* indicator
Turn on the unit.
Press STEREO for at least five seconds.
PAIRING button
STEREO
Once the indicator has shown the setting applied to the unit
as follows, the unit will turn on.
If the * indicator on the subwoofer does not glow after following the
procedure described here, see “No sound is coming from the
subwoofer” (p.50).
Glows (mode 1)
Off (mode 2)
43
En
Initializing the unit
Setting the dynamic range compression
Reset the settings of the unit to the factory presets.
Select the dynamic range compression level.
1
2
This function is set to “No compression” by default.
Turn off the unit.
1
2
Touch and hold } and z on the unit until all
indicators except the Alexa indicator flash.
Turn off the unit.
Use the remote control to select the desired
compression level.
Compresssion
level
Flash (initialized)
44
Function
Operations (buttons must
be pressed consecutively
within three seconds.)
Compression
(maximum)
Apply the maximum amount
of dynamic range
compression.
STEREO, VOLUME (+), and
then z
Compression
(standard)
Apply the standard amount
of dynamic range
compression for normal
home use.
STEREO, VOLUME (-), and
then z
No compression
Dynamic range compression
is not applied.
STEREO, |, and then z
En
The indicators show the compression level applied for several seconds.
Compression level
Indicators
Compression
(maximum)
Compression
(standard)
Glows (white)
No compression
Glow (white)
n NOTE
Press INFO to confirm the dynamic range compression level applied to the unit. For
details, see the following:
• “Showing audio information and function settings” (p.33)
45
En
APPENDIX
When any problem occurs (General)
When any problem occurs (Power and
system function)
Check the following first:
The power turns off suddenly
Refer to the following when the unit does not function properly.
• The power cords of the unit (center unit and subwoofer), TV and AV
devices are connected to AC wall outlets securely.
• The unit (center unit and subwoofer), TV and AV devices are turned on.
• The connectors of each cable are securely inserted into jacks on each
device.
If there is no problem with the power and cables, see the following:
• “When any problem occurs (Power and system function)” (p.46)
• “When any problem occurs (Audio)” (p.49)
• “When any problem occurs (Bluetooth®)” (p.51)
l The auto power standby function activated.
When the auto power standby function is enabled, the unit
automatically turns off in any of the following situations:
– No operations have been performed for 8 hours
– No audio has been input to the unit or no operations have been
performed with the unit for more than 10 minutes.
Turn on the unit again. If the auto power standby function is not
used, disable the function. For details, see the following:
– “Setting the auto power standby function” (p.38)
l The protection circuitry has been activated. (The STATUS
indicator flashes white or red.)
After confirming that all connections are made properly, turn on the
unit again. If the power still turns off frequently, unplug the power
cord from the AC wall outlet and contact the nearest authorized
Yamaha dealer or service center.
If the problem you are experiencing is not listed or if the instructions do
not help, turn off the unit, disconnect the power cord, and contact the
nearest authorized Yamaha dealer or service center.
46
En
The power cannot be turned on
The unit does not function correctly
l The protection circuitry has been activated three times
consecutively.
To protect the product, the power cannot be turned on. Unplug the
power cord from the AC wall outlet and contact the nearest
authorized Yamaha dealer or service center.
l The internal microcomputer is frozen due to an external electric
shock (such as lightning or excessive static electricity) or to a
drop in the power supply voltage.
Unplug the power cord from the AC wall outlet and plug it again.
l The firmware has not been updated properly. (The * indicator is
flashing.)
Use a USB flash drive to update the firmware. For details, see the
product information page on the Yamaha website.
– Product information page > Support (Download) > Firmware/
Software
The unit turns on by itself
No operations can be performed from
the unit’s touch panel
l Another Bluetooth device is being operated nearby.
Terminate Bluetooth connection with the unit. For details, see the
following:
– “Listening to audio from a Bluetooth® device” (p.30)
The TV’s 3D glasses do not work
l The unit is blocking the TV's 3D glasses transmitter.
Confirm the position of the TV's 3D glasses transmitter and position
the unit so that it does not obstruct the transmitter.
l The touch panel control is disabled.
Enable the touch panel control. For details, see the following:
– “Enabling/disabling touch panel control (Child Lock
function)” (p.39)
HDMI video is not displayed correctly on
TV screen
All indicators go out although the unit is
turned on (it may seem that the unit is
turned off)
l The HDMI cable is not securely connected.
Connect the HDMI cable properly. For details, see the following:
– “Connecting a TV that supports Audio Return Channel
(ARC)” (p.18)
– “Connecting a TV that does not support Audio Return Channel
(ARC)” (p.19)
l Indicator brightness is configured so that they do not light.
Change the brightness. For details, see the following:
– “Changing the brightness of the indicators (Dimmer)” (p.35)
47
En
l A communication error between the unit and connected device
has occurred.
A communication error may occur depending upon the generation of
the device connected to the unit. See the following if such an error
occurs:
– “Selecting the HDMI signal format” (p.43)
l The TV does not support HDCP version 2.2/2.3.
Connect the unit to the HDMI input jack on an HDCP v2.2/2.3compliant TV when playing video content that requires an HDCP
v2.2/2.3-compliant device.
l The batteries are weak.
Replace with new batteries. For details, see the following:
– “Replacing the battery in the remote control” (p.10)
l The remote control sensor of the unit is exposed to direct
sunlight or strong lighting.
Adjust the lighting angle or reposition the unit.
The TV cannot be operated using the TV’s
remote control
l The unit is connected to an HDMI input jack on the TV that does
not support HDCP v2.2/2.3.
Connect the unit to an HDMI input jack on the TV that supports HDCP
v2.2/2.3 when playing video content that requires an HDCP v2.2/2.3compliant device.
l The unit is blocking the TV’s remote control sensor.
Position the unit so that it does not obstruct the TV’s remote control
sensor.
The unit cannot be operated using the
TV’s remote control
When the unit is turned off, video and/or
audio from an AV device are not output
to the TV
l The HDMI control function is incorrect.
Confirm the settings are properly configured as follows.
– The HDMI control function of the unit is enabled.
– The HDMI control function is enabled on the TV.
– Set audio output to any option other than TV.
If the unit cannot be operated with the TV's remote control, even
after the settings have been applied correctly:
– Turn off the unit and the TV, and then turn them back on again.
– Disconnect the power cord of the unit and external devices
connected to the unit via HDMI cable. Plug them in again after
about 30 seconds.
l The HDMI control function is disabled.
Enable the HDMI control function. For details, see the following:
– “Configuring the HDMI control function” (p.36)
The unit cannot be operated using the
remote control
l The unit is out of the operating range.
Use the remote control within the operating range. For details, see
the following:
– “Operating range of the remote control” (p.9)
48
En
l The TV does not support the unit’s functions.
Even if your TV supports the HDMI control function, some functions
may not be available. For details, see documentation supplied with
your TV.
l The mute function is activated.
Cancel the mute function. For details, see the following:
– “Basic procedure for playback” (p.23)
l The volume is too low.
Turn up the volume. For details, see the following:
– “Basic procedure for playback” (p.23)
Alexa will not operate the unit
l Alexa is not properly configured.
Use the Sound Bar Controller app to configure Alexa. For details, see
the following:
– “Operating the unit using voice commands (Amazon Alexa)” (p.25)
l The power cord of the unit is not connected properly.
Make sure that the power cord of the unit is securely connected to an
AC wall outlet. For details, see the following:
– “Connecting to power” (p.20)
l Input jacks on an AV device are connected.
Connect the input jack on the unit and the output jack on the AV
device.
l The unit is not connected to a network.
Connect the unit to a network. For details, see the following:
– “Connecting to a network with the Sound Bar Controller
app” (p.22)
l Signals that the unit cannot play back are being input.
Change the digital audio output setting on the AV device to PCM,
Dolby Digital, or DTS.
Alexa does not respond when
summoned.
l The unit is configured so that HDMI audio input signals are
output from the TV.
Configure the unit so that HDMI audio input signals are output from
the unit. For details, see the following:
– “Configuring HDMI audio output” (p.37)
l The microphones are disabled.
Touch ) to enable the microphones.
l The HDMI control function is disabled.
When connecting a TV that supports ARC (Audio Return Channel) to
the unit using an HDMI cable only, enable the HDMI control function.
To output audio signals from the unit with the HDMI control function
disabled, connect the TV’s audio output jack to the unit’s TV input
jack (optical digital) via the optical digital audio cable.
For details, see the following:
– “Configuring the HDMI control function” (p.36)
– “Connecting a TV that does not support Audio Return Channel
(ARC)” (p.19)
When any problem occurs (Audio)
No sound
l Another input source is selected.
Select an appropriate input source. For details, see the following:
– “Basic procedure for playback” (p.23)
49
En
l [When the * indicator on the subwoofer flashes.] or [When the
STANDBY indicator on the subwoofer glows.]
The center unit and subwoofer are not connected due to a bad
wireless communication status.
– Move the subwoofer closer to the center unit.
– If the communication between the center unit and subwoofer is
obstructed by a metallic object or another object, change the
position of the center unit and subwoofer or change the
installation location of the subwoofer.
– If there is a device (microwave oven, wireless LAN, etc.) that emits
radio frequency signals, move the center unit and subwoofer away
from the device.
l Sound from an HDMI control-enabled TV is set for output from
the TV’s built-in speakers.
Use the TV’s HDMI settings to set audio output to any option other
than the TV’s built-in speakers.
No sound is coming from the subwoofer
l The subwoofer is not connected to an AC wall outlet.
Plug in the power cord of the subwoofer to an AC wall outlet. For
details, see the following:
– “Connecting to power” (p.20)
l [When the * and STANDBY indicators on the subwoofer flash.]
The protection circuitry in the subwoofer has been activated.
To protect the product, the power of the subwoofer cannot be
turned on. Unplug the power cord from the AC wall outlet and
contact the nearest authorized Yamaha dealer or service center.
l [When the * indicator on the subwoofer does not stop flashing.]
The center unit and subwoofer are not connected due to a bad
wireless communication status.
– Move the subwoofer closer to the center unit.
– If the communication between the center unit and subwoofer is
obstructed by a metallic object or another object, change the
position of the center unit and subwoofer or change the
installation location of the subwoofer.
– If there is a device (microwave oven, wireless LAN, etc.) that emits
radio frequency signals, move the center unit and subwoofer away
from the device.
– If the issue is not resolved after following the procedure described
above, pair the center unit and subwoofer manually. For details,
see the following:
“Pairing the center unit and subwoofer manually” (p.42)
l The playback source does not contain low-frequency signals.
Play back a sound source containing low-frequency signals, and
confirm that the sound is output from the subwoofer.
l The volume is too low.
Turn up the volume of the subwoofer. For details, see the following:
– “Basic procedure for playback” (p.23)
l The front side of the subwoofer is blocked.
Clear the area around the front side and the bass reflex port of the
subwoofer.
50
En
The volume decreases when the unit is
turned on
Noise is heard
l The automatic volume adjustment function is activated.
To prevent excessive loudness, the unit automatically controls its
volume within a certain level when the unit is turned on. Turn up the
volume as required. For details, see the following:
– “Basic procedure for playback” (p.23)
No surround effect
l The unit is too close to another digital or high-frequency device.
Move those devices away from the unit.
When any problem occurs
(Bluetooth®)
The unit cannot be connected to a
Bluetooth® device
l Stereo playback is selected.
Select surround playback or 3D surround playback. For details, see
the following:
– “Playback with 3D surround sound/surround sound” (p.28)
l Bluetooth is not selected as the input source.
Select Bluetooth as the input source. For details, see the following:
– “Listening to audio from a Bluetooth® device” (p.30)
l The volume is too low.
Turn up the volume. For details, see the following:
– “Basic procedure for playback” (p.23)
l The unit is too far away from the Bluetooth device.
Move the Bluetooth device closer to the unit.
l A device emitting electromagnetic waves (such as a microwave
oven, a wireless device, etc.) may be located nearby.
Do not use the unit near devices that emit electromagnetic waves.
l The TV or AV device is set to output 2-channel audio (such as
PCM) only.
Change the digital audio output setting on the TV or AV device to
multi-channel linear PCM or bitstream.
l The Bluetooth device you are using may not support the A2DP
profile.
Use a Bluetooth device that supports the A2DP profile.
l Sound is also heard from the TV built-in speakers.
Set the TV volume to minimum.
l The connection profile registered in the Bluetooth device may
not be functioning correctly.
Delete the connection profile in the Bluetooth device, and then
connect the Bluetooth device to the unit.
l The listening position is too close to the unit.
The listening position should be at some distance from the unit.
l The passkey for devices such as a Bluetooth adapter is not
“0000”.
Use a Bluetooth device with a passkey of “0000”.
51
En
l The unit is already connected to another Bluetooth device.
Terminate the current Bluetooth connection, and then connect to
the new device.
When any problem occurs (Network
trouble)
No sound can be heard or the sound cuts
off intermittently from a Bluetooth®
device
The network feature does not function
l The network parameters (IP address) have not been obtained
properly.
Enable the DHCP server function on the wireless router.
l The volume on the Bluetooth device may be too low.
Raise the volume on the Bluetooth device.
l The unit does not support IPv6 network.
Connect IPv4 network.
l Bluetooth is not selected as the input source.
Select Bluetooth as the input source. For details, see the following:
– “Listening to audio from a Bluetooth® device” (p.30)
The unit cannot connect to the Internet
via a wireless router (access point)
l Playback on the Bluetooth device has not been performed.
Perform playback on the Bluetooth device.
l The wireless router (access point) is turned off.
Turn on the wireless router.
l The sound output on the Bluetooth device may not be set to the
unit.
Select the unit as the output destination on the Bluetooth device.
l The unit and the wireless router (access point) are too far apart.
Place the unit and the wireless router (access point) closer to each
other.
l The connection to the Bluetooth device was terminated.
Connect with the Bluetooth device one more time.
l There is an obstacle between the unit and the wireless router
(access point).
Move the unit and the wireless router (access point) in a location
where there are no obstacles between them.
l The unit may be too far away from the Bluetooth device.
Move the Bluetooth device near the unit.
l A device emitting electromagnetic waves (such as a microwave
oven, a wireless device, etc.) may be located nearby.
Do not use the unit near devices that emit electromagnetic waves.
l The wireless router (access point) is configured to use a specific
wireless channel.
Change wireless router settings so that a channel is selected
automatically. If a specific channel will be specified, specify channel
1 or 11.
52
En
l The mobile device is not connected to the wireless router over a
wireless connection.
Connect the mobile device to the wireless router over a wireless
connection.
Wireless network is not found
l Microwave ovens or other wireless devices might disturb the
wireless communication.
Turn off these devices or move them farther away from the unit and
wireless router.
l The unit is connected to a multiple SSID router.
The router’s network splitter may be blocking access to the unit.
Connect the unit and mobile device to a network with the same
SSID. Try connecting to the primary SSID first.
l Access to the network is restricted by the firewall settings of the
wireless router (access point).
Check the firewall setting of the wireless router (access point).
l The wireless (Wi-Fi) function is disabled.
Enable the wireless (Wi-Fi) function. For details, see the following:
– “Enabling/disabling the wireless (Wi-Fi) function” (p.41)
The streaming service cannot be played
Firmware update via the network is
failed
l The selected streaming service is currently not available.
Play the streaming service later.
l Access to the network is restricted by the firewall settings of
your network devices (such as the router).
Check the firewall settings of your network devices. The streaming
service can be played only when it passes through the port
designated by each streaming service. The port number varies
depending on the streaming service.
l It may not be possible depending on the condition of the
network.
Update the firmware via the network again or use a USB memory
device.
The Sound Bar Controller app does not
detect the unit
l The unit and mobile device are not in the same network.
Check the network connections and router's settings, and then
connect the unit and mobile device to the same network.
l The mobile device is not connected to the network using the 2.4GHz band.
Connect the mobile device to the network using the 2.4-GHz band.
53
En
Specifications
Input jacks
Center unit specifications
HDMI
Center unit (ATS-CU2090) specifications are as follows.
Digital (optical)
Amplifier section
50 W × 2ch
HDMI
Speaker section
• Driver
• Frequency response
• Impedance
Acoustic suspension type
(non-magnetic shielding)
4.6 cm (1-3/4") cone × 4
• Frequency response
• Impedance
4 Ω (8 Ω × 2)
1 (UPDATE ONLY)
LAN
1 (NETWORK)
Function
Sink function (source device to this unit)
Bluetooth version
Ver 4.2
Supported profiles
A2DP
Supported codecs
Sink function: SBC, AAC
2.5 cm (1") dome × 2
9 kHz to 22 kHz
4Ω
Decoder
Supported audio signal
(HDMI/optical input)
USB
Bluetooth
190 Hz to 22 kHz
Tweeter
• Driver
1 (HDMI OUT (ARC))
Other jacks
Front L/R
• Type
1 (TV)
Output jacks
Maximum rated output power
• Front L/R
1 (HDMI IN)
Bluetooth class
Bluetooth Class 2
PCM (up to 5.1ch)
Range (line-of-sight)
Dolby Digital (up to 5.1ch)
DTS Digital Surround (up to 5.1ch)
Supported content protection method
54
En
Approx. 10 m (33 ft)
SCMS-T (sink function)
General
[U.K. and Europe models]
• Radio frequency
• Maximum output power (EIRP)
2402 MHz to 2480 MHz
Power supply
8.8 dBm (7.6 mW)
Network
Ethernet standard
Supported codecs
100BASE-TX/10BASE-T
• [U.S.A. and Canada models]
AC 100 to 120 V, 50/60 Hz
• [Australia model]
AC 100 to 240 V, 50/60 Hz
• [U.K., Europe and Russia models ]
AC 100 to 240 V, 50/60 Hz
• [General model]
AC 100 to 240 V, 50/60 Hz
• [Taiwan and Mexico models]
AC 100 to 120 V, 50/60 Hz
WAV (PCM format only) /FLAC: up to 192 kHz
• [China model]
AC 100 to 240 V, 50/60 Hz
ALAC: up to 96 kHz
• [Korea model]
AC 100 to 240 V, 50/60 Hz
MP3/WMA/MPEG-4 AAC: up to 48 kHz
Power consumption
Wi-Fi function
• Wireless LAN standards:
• Radio frequency band
• Available security method:
IEEE802.11b/g/n
Standby power consumption
2.4 GHz
• [U.S.A., Canada, Taiwan and Mexico models]
WEP, WPA2-PSK (AES), Mixed Mode
– HDMI control off, network standby off
• Radio frequency
2402 MHz to 2482 MHz (20 MHz)
• Maximum output power (EIRP)
2.4 GHz band
0.2 W
– HDMI control off, network standby on (Wired/Wi-Fi/
Bluetooth)
[U.K. and Europe models]
2.4 GHz band
25 W
4.3 W (Voice Control Ready)
1.6/1.8/1.7 W
– HDMI control on, network standby off
0.6 W
– HDMI control on, network standby on
2.2 W
• [U.K. and Europe models and other models]
18.1 dBm (64.6 mW)
– HDMI control off, network standby off
0.2 W
– HDMI control off, network standby on (Wired/Wi-Fi/
Bluetooth)
1.6/1.8/1.7 W
– HDMI control on, network standby off
0.6 W
– HDMI control on, network standby on
2.2 W
Dimensions (W x H x D)
930 × 62 × 109 mm
(38-5/8" × 2-1/2" × 4-1/4")
55
En
Weight
General
2.7 kg (6 lbs)
n NOTE
Power supply
The contents of this manual apply to the latest specifications as of the publishing date. To
obtain the latest manual, access the Yamaha website then download the manual file.
• [U.S.A. and Canada models]
AC 100 to 120 V, 50/60 Hz
• [Australia model]
AC 100 to 240 V, 50/60 Hz
Subwoofer specifications
• [U.K., Europe and Russia models ]
AC 100 to 240 V, 50/60 Hz
• [General model]
AC 100 to 240 V, 50/60 Hz
Subwoofer (NS-WSW44) specifications are as follows.
Amplifier section
Maximum rated output power
• Driver
• Frequency response
• Impedance
• Radio frequency band
• Transmission range
• Maximum output power (EIRP)
• [Korea model]
AC 100 to 240 V, 50/60 Hz
20 W
Standby power consumption
Bass reflex type
(non-magnetic shielding type)
• [U.S.A., Canada , Taiwan and Mexico models]
0.8 W
• [U.K. and Europe models and other models]
0.8 W
16 cm (6-1/2") cone × 1
Dimensions (W × H × D)
34 Hz to 190 Hz
191 × 420 × 406 mm
(7-1/2" × 16-1/2" × 16)
2Ω
Weight
2.4 GHz
10 m ([33 ft] without interference)
7.9 kg (17.4 lbs)
n NOTE
The contents of this manual apply to the latest specifications as of the publishing date. To
obtain the latest manual, access the Yamaha website then download the manual file.
[U.K. and Europe models]
• Radio frequency
AC 100 to 120 V, 50/60 Hz
AC 100 to 240 V, 50/60 Hz
Power consumption
100 W
Speaker section
• Type
• [Taiwan and Mexico models]
• [China model]
2405.35 MHz to 2477.35 MHz
9.0 dBm (7.9 mW)
56
En
Supported HDMI audio and video formats
Copyright protection standard
The following HDMI audio and video formats can be used by the unit.
n NOTE
Audio signals
• Refer to documentation supplied with the AV device, and set the device appropriately.
• When CPPM copy-protected DVD-Audio is played back, video and audio signals may
not be output depending on the type of the DVD player.
• The unit is not compatible with HDCP-incompatible HDMI or DVI devices. Refer to
documentation supplied with the HDMI or DVI device for HDCP compatibility.
• To decode audio bitstream signals on the unit, set the input source device
appropriately so that the device outputs the bitstream audio signals directly (does not
decode the bitstream signals on the device). Refer to documentation supplied with the
device for details.
• The resolution of transmitted video signal varies according to specifications of the TV
connected to the unit.
• The contents of this manual apply to the latest specifications as of the publishing date.
To obtain the latest manual, access the Yamaha website to download the manual file.
Audio signal types
Audio signal formats
2ch Linear PCM
2ch, 32 kHz to 192 kHz, 16/20/24 bit
Multi-ch Linear PCM
6ch, 32 kHz to 192kHz, 16/20/24 bit
Bitstream
Dolby Digital, DTS
Video signals
The unit is compatible with the following video signals.
• Deep Color
• x.v.Color
This unit supports HDCP version 2.3.
• 3D video signal
• High Dynamic Range (HDR) video
– HDR10
– HLG
The unit is compatible with the following resolutions.
• VGA
• 480i/60 Hz
• 480p/60 Hz
• 576i/50 Hz
• 576p/50 Hz
• 720p/60 Hz, 50 Hz
• 1080i/60 Hz, 50 Hz
• 1080p/60 Hz, 50 Hz, 30 Hz, 25 Hz, 24 Hz
• 4K/60 Hz, 50 Hz, 30 Hz, 25 Hz, 24 Hz
57
En
Supported digital audio formats
The following digital audio formats can be used by the unit.
Optical
Audio signal types
Audio signal formats
2ch Linear PCM
2ch, 32 kHz to 96 kHz, 16/20/24 bit
Bitstream
Dolby Digital, DTS
HDMI (ARC)
Audio signal types
Audio signal formats
2ch Linear PCM
2ch, 32 kHz to 96 kHz, 16/20/24 bit
Bitstream
Dolby Digital, DTS
n NOTE
The contents of this manual apply to the latest specifications as of the publishing date. To
obtain the latest manual, access the Yamaha website to download the manual file.
58
En
Information for qualified contractors or dealers
Mounting the center unit on a wall
1
Mount the center unit on a wall using the screw holes on the rear panel.
Attach the mounting template (supplied) on a wall
and mark for the screw holes.
Mounting template (supplied)
CAUTION
• Please have a qualified contractor or dealer when mounting the center unit on a
wall. Some skills and experience are required for safe installation.
• To prevent the center unit from falling, attach it to a wall constructed of drywall
(plasterboard).
• Make sure you use screws (sold separately) that can support the weight of the
installation. Using clamps other than specified screws, such as short screws, nails,
and two-sided tape, may cause the center unit to fall.
• Fix the cables in place where they will not become loose. If your foot or hand
accidentally gets caught on a loose cable, the center unit may fall.
• Do not lean on the unit or apply excessive force to the top of the center unit. Doing
so may cause the center unit to fall.
• Check that the center unit is securely fixed after the installation. Yamaha will bear
no responsibility for any accidents caused by improper installations.
Screw holes
Tape or thumbtacks
2
Remove the mounting template from the wall, and
then install screws (sold separately) at the points
marked on the wall.
457 mm
(18")
4 to 5 mm
(#8 to #10)
7 to 9 mm
(1/4" to 3/8")
4.5 to 6 mm
(1/8" to 1/4")
59
En
20 mm (3/4") or
more
3
Hang the center unit on the screws.
Mounting holes on
the rear of the
center unit
60
En
Yamaha Global Site
https://www.yamaha.com/
Yamaha Downloads
https://download.yamaha.com/
Manual Development Group
© 2019 Yamaha Corporation
Published 09/2019 NV-B0
10-1 Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650 Japan
AV18-0062
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising