Yamaha | HTR-4067 | Installation manual | Yamaha HTR-4067 Firmware Update Installation Manual

Yamaha HTR-4067 Firmware Update Installation Manual
FIRMWARE UPDATING PROCEDURE
IMPORTANT NOTICE
Do not attempt to update your Yamaha receiver using any other data file except those provided directly from the
Yamaha website or through your network connection.
Follow the instructions carefully and do not attempt any other procedures not specified in the instructions provided by
Yamaha.
Improperly updated products may cause improper operation, and any parts or service required to restore proper
operation will not be covered under the Yamaha Limited Warranty.
Choose from the following 2 methods to update to the latest firmware.
Click here for Firmware Update Through the Internet
(Connection to the Internet is required)
Click here for Firmware Update by USB
(A USB thumb drive is required)
In case of error, see the Troubleshooting section
1
Firmw
ware Update Thro
ough the Internet
Requirrement:
Intternet connecttion
Yo
our receiver is connected to the Internet iff you can receiive Internet rad
dio stations.
(S
See owner’s manual for deta
ails)
1 Po
ower off the
t receiiver (Stan
ndby mo
ode)
2 En
nter the A
ADVANC
CED SETU
UP mode
e
While pressing the
e STRAIGHT key, press the
e
k and keep STRAIGHT ke
ey pressed until
(power) key
“ AD
DVANCED SETUP ” appearss on the front panel display.
* “ ADVANCED SETUP ” is displayed only ffor a few secoonds.
3 Se
elect “FIR
RM UPDA
ATE” from the me
enu
a. Press
P
the PRO
until “ UPDATE
E.....USB ” is d
displayed.
OGRAM key u
b. Then,
T
press STRAIGHT keyy until “ UPDAT
TE.NETWORK
K ” is displayed.
4 Start firmw
ware update
a. P
Press INFO ke
ey to start the update.
(
(Update
proce
ess may take up
u to 15 minute
es)
TE SUCCESS ” appears, thiss means your receiver is alrready up-to-da
ate. In this case
e, power off to
o exit
* If “ UPDAT
from Advan
nced Setup. Y
Your AV receivver is ready forr normal use.
Firmware upda
ate in progres
ss
Caution
DO NOT in
nterrupt powerr during the up
pdate.
In case the
e power is accidentally cut offf resulting in a condition wh
here you can’t recover norma
al operation, re
efer to
the trouble
eshooting meth
hod (Troubles
ast page.
shooting CAS
SE 2) on the la
b. When
W
completted, “ UPDATE
E SUCCESS ” appears on th
he display.
c. Turn
T
off the po
ower of the recceiver by presssing the
INFOke
ey
(p
power) key.
STRAIGHT
T key
(powerr) key
PROGRAM key
k
2
5 Se
elect “FIR
RM UPDA
ATE” from the me
enu
a. Power
P
on the A
AV receiver an
nd press the S
n the remote co
ontrol.
SETUP key on
b. Select
S
“Network” > “Networkk Update”.
c. Confirm
C
that th
he firmware ve
ersion is updatted to the latesst version.
SETUP
P key
Congrratulation
ns!
You have completed the
e firmware upd
date. Your AV
V receiver is ready for norma
al use.
3
Firmw
ware Update by USB
Require
ement:
SB thumb drivve, with enough free space to
o store over 25MB.
US
(F
File system with FAT16 or FA
AT32 format)
Firmware file pro
ovided by YAM
MAHA, “R03xxx-xxxx.bin”.
1 Prrepare US
SB thumb drive ffor the up
pdate
Dow
wnload the firm
mware, unzip a
and copy “R03xx-xxxx.bin” in
nto the root dirrectory of the USB
U
thumb drrive.
Drag & Drop the file into USB thumb d
drive.
2 Po
ower off the
t receiiver (Stan
ndby mo
ode)
3 Ins
sert the U
USB thum
mb drive
e
USB
B port is locate
ed at the lowerr left corner of the front pane
el.
4 En
nter the A
ADVANC
CED SETU
UP mode
e
While pressing the
e STRAIGHT key, press the
e
k and keep STRAIGHT ke
ey pressed until
(power) key
“ AD
DVANCED SETUP ” appearss on the front panel display.
5 Se
elect firm
mware up
pdate from
m the me
enu
Presss the PROGR
USB ” is displa
ayed.
RAM key until “UPDATE.....U
STRAIGHT
T key
(power)) key
PROGRAM key
k
U
USB port
4
6 Start firmw
ware update
a. P
Press INFO ke
ey to start the update.
(
(Update
proce
ess may take up
u to 10 minute
es)
TE SUCCESS ” appears, thiss means your receiver is alrready up-to-da
ate. In this case
e, power off to
o exit
* If “ UPDAT
from Advan
nced Setup. Y
Your AV receivver is ready forr normal use.
Firmware upda
ate in progres
ss
Caution
DO NOT in
nterrupt powerr during the up
pdate.
In case the
e power is accidentally cut offf resulting in a condition wh
here you can’t recover norma
al operation, re
efer to
the trouble
eshooting meth
hod (Troubles
ast page.
shooting CAS
SE 2) on the la
b. When
W
completted, “ UPDATE
E SUCCESS ” appears on th
he display.
c. Turn
T
off the po
ower of the recceiver by presssing the
(p
power) key.
INFO key
(powe
er) key
U
USB port
7 Se
elect “FIR
RM UPDA
ATE” from the me
enu
a. Power
P
on the A
AV receiver an
nd press the S
n the remote co
ontrol.
SETUP key on
b. Select
S
“Network” > “Networkk Update”.
c. Confirm
C
that th
he firmware ve
ersion is updatted to the latesst version.
SETUP
P key
Congrratulation
ns!
You have completed the
e firmware upd
date. Your AV
V receiver is ready for norma
al use.
5
Troub
bleshooting
CASE 1 Erro
or messa
age appe
eared durring the update
u
Cause:
Metho
od:
For so
ome reason, th
he receiver ca
an’t read the firrmware data.
For yo
our solution, check the follow
wing
[Update through
h Internet]
❏Chheck Internet cconnection.
Yo
our Internet co
onnection is wo
orking by playiing an Internet radio station.
(S
See owner’s manual for details)
[Update by USB thumb drive
e]
❏USSB thumb drivve is connectedd properly to thhe receiver.
❏USSB thumb drivve is not passwword protectedd.
(A
AV receiver can
nnot read data
a from a securrity protected USB
U
thumb driive)
❏Maake sure the USB thumb drive
d
is inserte
ed before the receiver is po
owered on forr the
up
pdate.
❏Thhe firmware daata, R03xx-xxxxx.bin is storedd in the root directory of the USB thumb drive.
❏Thhere is no otheer data except the firmware ddata in the USSB thumb drivee.
❏Noo folders are ccreated in the UUSB thumb drrive.
Else, retry the update by USB
B using anothe
er USB thumb drive.
CASE 2 Firm
mware up
pdate do
oesn’t sta
art for oth
her reaso
ons
● Re
eceiver does
sn’t power u
up after the u
update.
● Orr, error mess
sage appearred when co
onfirming the
e firmware v
version.
Recovery method
d using USB
B method:
1. Un
nplug the AC p
power cable frrom wall outlett.
2. Inssert the USB thumb
t
drive which
w
has the ffirmware data stored inside, into the USB port
loccated on the frront panel.
3. Prress and hold the INFO keyy and keep it pressed while
e you plug the
e AC power ccable
ba
ack into the wa
all outlet again
n.
“U
USB UPDATE ” will appear on
o the front dissplay. Then, re
elease the INF
FO key.
4. Th
he update will start automatically.
E SUCCESS ” appears on the display, firm
5. W
When “ UPDATE
mware update
e is completed..
Po
ower off the re
eceiver and rem
move the USB
B thumb drive.
6. Co
onfirm updated
d firmware verrsion.
INFO kkey
U
USB
port
6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising