Yamaha | SRT-1500 | Installation manual | Yamaha SRT-1500 Firmware Update Installation Manual

Yamaha SRT-1500 Firmware Update Installation Manual
■ UPDATING THE UNIT’S FIRMWARE
New firmware that provides additional features or product
improvements will be released as needed. If the unit is connected
to the Internet, you can download the firmware via the network and
update it.
4
4
Press the ENTER key.
The TV screen goes black and firmware update begins.
The firmware update will begin.
The indicators on the front panel glow to indicate progress
during the update.
When the unit is turned on for the first time after a new version of the
unit’s firmware has been released, a message indicating that a
firmware update is available will be displayed on the TV screen,
and an envelope icon ( ) will be displayed in the setup menu.
Press the key on the front panel while pressing the VOLUME – key
on the unit.
The indicators on the front panel glow to indicate progress during the update.
Update progress
Update progress
The unit’s firmware can be updated as follows.
• Update firmware from “Network Update” in the setup menu.
• If there are multiple firmware updates, the indicators will start glowing as
each firmware update begins.
• Update firmware by connecting a USB flash drive to which the
unit’s firmware update has been saved.
/
ENTER
• Update firmware using the dedicated MusicCast CONTROLLER
app installed on a mobile device. Follow MusicCast
CONTROLLER guides to operate the app and update the
firmware.
5
• If there are multiple firmware updates, the indicators will start glowing as each firmware update
begins.
5
When the indicators on the front panel glow alternately as shown
below, press the (power) key on the unit's front panel.
When the indicators on the front panel glow alternately as shown
below, press the
(power) key on theunit's front panel.
All indicators glow
All indicators glow
SETUP
Notes
Alternates
• Do not operate the unit or disconnect the power cable or network cable during
firmware update. Firmware update takes about 20 minutes or more (depending
on your Internet connection speed).
Alternates
• If the Internet connection speed is slow, or the unit is connected to the wireless
network, network update may not be possible depending on the condition of
the network connection. In this case, update the firmware using the USB flash
drive.
• To perform the following procedure, your TV must be connected to the unit via
HDMI.
• For details on update, visit the Yamaha website.
Using “Network Update” in the setup menu
to update firmware
1
One indicator glows
One indicator glows
The firmware update is complete.
The firmware update is complete.
• If the firmware update fails, the indicator at far right will flash blue. Use the (power) key to turn the unit off
and then on again, and repeat the procedure from step 1 again. If the firmware update fails again, confirm
that the unit is properly connected to a network.
• If the firmware update fails, the indicator at far right will flash blue. Use the (power) key to turn the unit off
and then on again, and repeat the procedure from step 1 again. If the firmware update fails again, confirm
the following.
– The USB flash drive is correctly connected to the UPDATE ONLY jack
– See information provided as firmware updates are performed, and be sure that the USB flash drive
contains the firmware update for this unit.
– The unit is properly connected to a network.
Press the SETUP key twice.
The setup menu is displayed on the TV screen.
2
Use the / keys to select “Network”, and then
press the ENTER key.
3
Use the / keys to select “Network Update”, and
then press the ENTER key.
The following screen is displayed when firmware updates
are available.
• To cancel the operation without updating the firmware, press the SETUP
key.
Updating firmware with connection of a USB flash drive
Download the latest firmware version from the Yamaha website to a USB flash drive,
which can then be used to update the unit’s firmware.
See information provided when updating firmware for details.
1
2
3
Save this unit’s firmware to a USB flash drive.
Turn off the unit.
Connect the USB flash drive to the UPDATE ONLY jack on the unit’s
rear panel.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising