Yamaha | TX-10 | Owner's Manual | Yamaha TX-10 OWNER'S MANUAL

Yamaha TX-10 OWNER'S MANUAL
TX-10
Natural Sound AM/FM Stereo Tuner
Syntonisateur AM/FM stéréo de la série “Natural Sound”
“Natural Sound” MW/UKW-Stereo-Tuner
Natural Sound AM/FM stereotuner
Sintonizzatore stereo AM/FM a suono naturale
Sintonizador estéreo de AM/FM de sonido natural
Natural Sound Stereo Tuner
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
SUPPLIED ACCESSORIES
ACCESSOIRES FOURNIS
MITGELIEFERTE ZUBEHÖRTEILE
MEDFÖLJANDE TILLBEHÖR
ACCESSORI IN DOTAZIONE
ACCESORIOS INCLUIDOS
BIJGELEVERDE ACCESSOIRES
●
●
●
●
●
●
●
●
●
●
●
●
●
●
2
Indoor FM Antenna
Antenne FM intérieure
UKW-Innenantenne
FM inomhusantenn
Antenna FM per interni
Antena FM interior
FM Binnenantenne
Audio connection cord
Câble de connexion audio
Audio-Anschlußkabel
Audio anslutningssladdar
Cavo di collegamento audio
Cable de conexión de audio
Audio aansluitkabel
●
●
●
●
●
●
●
After unpacking, check that the following parts are contained.
Après le déballage, vérifier que les pièces suivantes sont incluses.
Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind.
Kontrollera efter det apparaten packats upp att följande delar finns med.
Verificare che tutte le parti seguenti siano contenute nell’imballaggio dell’apparecchio.
Desembale el aparato y verificar que los siguientes accesorios están en la caja.
Controleer na het uitpakken of de volgende onderdelen voorhanden zijn.
●
●
●
●
●
●
●
AM Loop Antenna
Cadre-antenna AM
MW-Rahmenantenne
AM ramantenn
Antenna AM ad anello
Antena de cuadro de AM
AM Lusantenne
FEATURES
CONTENTS
•
•
•
•
•
•
Supplied Accessories......................................................2
Caution............................................................................3
Connections ....................................................................4
Tuning Operations ..........................................................7
Preset Tuning..................................................................9
Receiving RDS Stations (U.K. and Europe models only)
......................................................................................12
Troubleshooting ............................................................17
Specifications................................................................18
40 Station Random Access Preset Tuning
Automatic Preset Tuning
Multi-Status Station Memory
Direct PLL Synthesizer Tuning
Preset Station Shifting Capability
Multi-Functions for RDS Broadcast Reception
(U.K. and Europe models only)
English
Thank you for selecting this YAMAHA stereo tuner
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1. This unit is a sophisticated stereo tuner. To assure proper
operation and the best possible performance, please read
this manual carefully.
2. Choose the installation location for the unit carefully.
Avoid placing it in direct sunlight or close to a source of
heat. Also avoid locations subject to vibration and
excessive dust, heat, cold or moisture. Keep it away from
such sources of hum as transformers or motors.
3. Do not open the cabinet, because this may result in
damage to the unit or electrical shock. If a foreign object
should get into the unit, contact your local dealer.
4. When not planning to use this unit for long periods of time
(ie., vacation, etc.), disconnect the AC power plug from the
wall outlet.
5. To prevent lightning damage, disconnect the AC power
plug and disconnect the antenna cable when there is an
electrical storm.
6. When disconnecting the power plug from the wall outlet,
always pull directly on the plug; never pull the cord itself.
7. Do not use force when operating switches and other
IMPORTANT
Please record the serial number of this unit in the space
below.
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION (FOR CANADA MODEL)
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT AND FULLY INSERT.
FOR CANADIAN CUSTOMER
THIS DIGITAL APPARATUS DOES NOT EXCEED THE “CLASS B”
LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL
APPARATUS SET OUT IN THE RADIO INTERFERENCE
REGULATION OF THE CANADIAN DEPARTMENT OF
COMMUNICATIONS.
controls.
8. When moving the unit, be sure to first disconnect the
power plug and disconnect all wires connected from the
unit to other equipment.
9. Do not attempt to clean this unit with chemical solvents,
because this may damage the finish. Use a clean, dry
cloth.
10. Be sure to read the “TROUBLESHOOTING” section of this
manual for advice on common operating errors before
concluding that the unit is faulty.
11. Keep this manual in a safe place for future reference.
12. Voltage Selector (General Model only)
The voltage selector on the rear panel of this unit must be set
for your local main voltage BEFORE plugging into the AC
main supply.
Voltages are 110-120/220-240V AC, 50/60 Hz.
FREQUENCY STEP switch (General Model only)
Because the interstation frequency spacing differs in different
areas, set the FREQUENCY STEP switch (located at the rear)
according to the frequency spacing in your area.
Before setting this switch, disconnect the AC power plug of this unit
from the AC outlet.
The apparatus is not disconnected from the AC power
source as long as it is connected to the wall outlet, even if
the apparatus itself is turned off.
For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the
instructions described below.
Note: The plug severed from the mains lead must be
destroyed, as a plug with bared flexible cord is hazardous if
engaged in a live socket outlet.
Special Instructions for U.K. Model
IMPORTANT
THE WIRES IN THE MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
The colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying
the terminals in your plug. Proceed as follows: the wire
which is coloured BLUE must be connected to the terminal
which is marked with the letter N or coloured BLACK. The
wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
3
CONNECTIONS
ANTENNA CONNECTIONS
●
●
Each antenna should be connected to the designated terminals correctly, referring to the following figure.
Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal
strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience
poor reception quality, an outdoor antenna may result in improvement.
Outdoor FM antenna
Outdoor AM antenna
Indoor FM
antenna
(included)
FM ANT
AM loop
antenna
(included)
GND AM ANT
75Ω UNBAL.
75-ohm
antenna
adapter
300-ohm flat
ribbon cable
75-ohm coaxial cable
4
75-ohm/300-ohm
antenna adapter
Ground
English
Connecting the indoor FM antenna
*If you connect an outdoor FM antenna to this unit, do not connect the indoor FM antenna to this unit.
Connecting the AM loop antenna
➁
Orient so that the best
reception is obtained.
➂
➀
* The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall.
* The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit.
m Optional outdoor FM antenna
Consult with your dealer or authorized service center about the
best method of selecting and erecting an outdoor FM antenna.
The choice of the feeder cable is also important. Flat ribbonshaped twin-lead cable performs well electrically, and is
cheaper and somewhat easier to handle when routing it
through windows and around rooms. Coaxial cable is more
expensive, does a much better job of minimizing interference,
is less prone to the effects of weather and close-by metal
objects, and is nearly as good a signal conductor as feeder
cable, particularly for foam-type coaxial cables. Coaxial cable
is somewhat more difficult to install at the point where the
cable enters the building. If coaxial cable is selected, make
sure the antenna is designed to be used with that type of
cable.
300-ohm feeder
cable
75-ohm coaxial
cable
* Use a 75-ohm/300-ohm antenna adapter (not included) or a
75-ohm antenna adapter (not included) for connections.
300-ohm feeder cable
75-ohm coaxial cable
75-ohm/300-ohm antenna adapter
75-ohm coaxial
cable
75-ohm antenna
adapter
Notes for FM antenna installation
● To minimize automobile ignition noise, locate the antenna
as far from heavy traffic as possible.
● Keep the feeder cable or coaxial cable as short as possible.
Do not bundle or roll up excess cable.
● The antenna should be at least two meters (6.6 feet) from
reinforced concrete walls or metal structures.
5
m Optional outdoor AM antenna
GND terminal
For maximum safety and minimum interference, connect
the GND terminal to a good earth ground. A good earth
ground is a metal stake driven into moist earth.
In steel buildings or at a great distance from the transmitter, it
may be necessary to install an outside long wire antenna.
CONNECTIONS TO THE AMPLIFIER
●
Before making any connections, switch OFF the power to
this unit and the amplifier or other component.
●
Be sure that the connections from the left (“L”) and right
(“R”) LINE OUT terminals are connected to the
corresponding (left and right) input terminals of the amplifier
or other component.
* When connecting with the YAMAHA amplifier AX-10,
connect this unit’s LINE OUT terminals to the TUNER
terminals (numbered 2) on the rear of AX-10.
Amplifier
R
L
2
TUNER
Connection cord (included)
This unit
FM ANT
GND AM ANT
LINE OUT
2
75Ω UNBAL.
L
R
To AC outlet
* This unit has a remote control sensor. It receives signals
from the remote control transmitter provided with a
YAMAHA amplifier.
Remote control sensor
6
Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is
possible. However, if signals of the station you want to select are weak, you must tune to it manually (MANUAL TUNING).
English
TUNING OPERATIONS
AUTOMATIC TUNING
<U.K. and Europe models>
1
3
1
4
<General model>
2 5, 6
1
5
STANDBY/ON
3 4
2 5, 6
Tune to a desired station.
PRESET STATIONS
DOWN
2
Select the reception band while watching the display.
TUNING
FM/AM
To tune to a higher frequency, press the UP button
once. To tune to a lower frequency, press the DOWN
button once.
or
3
6
TUNING
MODE
AUTO
AUTO/
MAN’L MONO
4
UP
If the station where tuning search stopped is not the
desired one, press again.
PRESET STATIONS
DOWN
UP
If “PRESET” is being illuminated on the display, press
the KEY MODE button to turn it off.
TUNING
<U.K. and Europe models>
ENTER/
KEY MODE
* If the tuning search does not stop at the desired station
(because the signals of the station are weak), change
to the MANUAL TUNING method as described on the
following page.
PRESET
<General model>
KEY MODE
To turn off the power
Press the POWER switch again.
ENTER
7
MANUAL TUNING
<U.K. and Europe models>
2
1
2
<General model>
3
4
Follow steps 1 and 2 on the previous page.
2 3
4
4
Tune to a desired station manually.
PRESET STATIONS
DOWN
TUNING
MODE
UP
“AUTO” goes off.
AUTO/
MAN’L MONO
TUNING
3
* To continue tuning search, press and hold the button.
If “PRESET” is being illuminated on the display, press
the KEY MODE button to turn it off.
<U.K. and Europe models>
Note
If you tune to an FM station manually, it is received in
monaural mode automatically to increase the signal quality.
ENTER/
KEY MODE
PRESET
<General model>
KEY MODE
ENTER
➀
Display information
1
AUTO
ST
MHz
2 3
8
➁
➂
Displays the band and frequency of the received station.
* <U.K. and Europe models only>
If an RDS station is received, the frequency is then
replaced by the station name. (However, if the PS data
cannot be received within 5 seconds, “NO PS” flashes,
and then it returns to the frequency display.)
Refer to page 13 for details.
Illuminates when an FM stereo broadcast is received in
stereo.
Indicates the signal level of the received station.
English
PRESET TUNING
MANUAL PRESET TUNING
This unit can store station frequencies selected by tuning operation. With this function, you can recall any desired station by only
selecting the preset station number where it is stored. Up to 40 stations (8 stations x 5 pages) can be stored.
<U.K. and Europe models>
2, 5
<General model>
2
3, 1 4, 3
To store stations
1
2
2, 5
2
3, 1 4, 3
To recall a preset station
Tune to a desired station.
(Refer to the previous page for tuning procedures.)
1
Select the page where the preset station is stored.
A/B/C/D/E
PRESET
MEMORY
MEMO
MAN’L/
AUTO FM
3
Flashes on and off
for about 5 seconds.
2
If “PRESET” is not being illuminated on the display,
any preset station cannot be recalled. If so, press the
KEY MODE button to turn it on.
<U.K. and Europe models>
Select a desired page (A – E) of preset stations while
watching the display before “MEMO” goes off from the
display.
A/B/C/D/E
PRESET
ENTER/
KEY MODE
PRESET
<General model>
KEY MODE
4
Select a preset station number (1–8) while watching the
display before “MEMO” goes off from the display.
ENTER
PRESET STATIONS
DOWN
UP
3
PRESET STATIONS
DOWN
UP
TUNING
5
TUNING
MEMORY
PRESET
AUTO
ST
Select the preset station number.
MHz
MAN’L/
AUTO FM
Shows the displayed station
has been programmed to A1.
* In the same way, program other stations to A2, A3 ... A8.
* You can program more stations on other pages in the
same way by selecting other pages in step 3.
Notes
● A new setting can be programmed in place of the former
one.
● For presets, the setting of the reception mode (stereo or
monaural) is stored along with the station frequency.
9
AUTOMATIC PRESET TUNING
You can also make use of an automatic preset tuning function for FM stations only. By this function, this unit performs automatic
tuning and stores FM stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the
manual preset tuning method on page 9.
<U.K. and Europe models only>
* Only RDS stations can be stored by this function.
<U.K. and Europe models>
2
<General model>
3
1
2
3
1
To store stations
1
When the automatic preset tuning is finished
FM/AM
The display shows the frequency of the last preset station.
Check the contents and the number of preset stations by
following the procedure of the section “To recall a preset
station” on page 9.
To recall a preset station
2
MEMORY
AUTO
ST
PRESET
MHz
MAN’L/
AUTO FM
Press and hold for
about 3 seconds.
3
MEMO
Flashes.
<U.K. and Europe <General model>
models>
KEY MODE
ENTER/
KEY MODE
ENTER
The automatic preset tuning begins from the frequency
currently displayed. Received stations are programmed to
A1, A2 ... A8 sequentially.
* If more than 8 stations are received, they are also
programmed to the preset station numbers on other pages
(B, C, D and E) in that order.
If you want to store the first station received by the
automatic preset tuning to a desired preset station
number.
If, for example, you want to store the first received station to
C5, select “C5” by using the A/B/C/D/E button and the
PRESET STATIONS DOWN/UP buttons after pressing the
MEMORY button in step 2. Then press the ENTER button. The
first received station is stored to C5, and next stations to C6,
C7 ... sequentially.
If stations are stored up to E8, the automatic preset tuning is
finished automatically.
10
Simply follow the procedure of the section “To recall a preset
station” on page 9.
<U.K. and Europe models only>
* A recalled station is shown by the frequency or station name
on the display.
Notes
● You can replace a preset station by another FM or AM
station manually by simply following the procedure of the
section “To store stations” on page 9.
<General model only>
● If the number of received stations is not enough to be stored
up to E8, the search is finished automatically when it
reaches the highest frequency after searching through all
frequencies.
● With this function, only FM stations with sufficient signal
strength are stored automatically. If the station you want to
program is week in signal strength, tune to it in monaural
manually and program it by following the procedure of the
section “To store stations” on page 9.
<U.K. and Europe models only>
● The automatic preset tuning search will be performed
through all RDS network frequencies until stations are
stored up to E8. If the number of received stations is not
enough to be stored up to E8, the search is finished
automatically after searching through all frequencies.
● With this function, only RDS stations with sufficient signal
strength are stored automatically. If the station you want to
program is weak in signal strength, tune to it in monaural
manually and program it by following the procedure of the
section “To store stations” on page 9.
* There may be a case that this function cannot receive a
station which could be received by the automatic tuning
method. This is because this function receives a large
volume of PI (Program Identification) data along with the
station.
English
EXCHANGING PRESET STATIONS
You can exchange the places of two preset stations with each other as shown below.
<U.K. and Europe models>
<General model>
24
24
Example)
If you want to shift the preset station on E1 to A5, and vice
versa.
1
Recall the preset station on E1 (by following the method
of “To recall a preset station” on page 9).
2
<U.K. and Europe
models only>
4
<U.K. and Europe
models only>
<General model only>
KEY MODE
<General model only>
EDIT
ENTER/
KEY MODE
ENTER
PS/PTY/SEEK
SHIFT/
EDIT
Press and hold for
about 3 seconds.
MEMO
Shows the exchange of stations is completed.
Flashes
3
Next, recall the preset station on A5 by following the
same method with step 1.
Flashes
Memory back-up
The memory back-up circuit prevents the programmed data
from being lost even if the POWER switch is set off or the
power plug is disconnected from the AC outlet or the power is
cut due to temporary power failure. If, however, the power is
cut for more than one week, the memory may be erased. If so,
it can be re-programmed by simply following the PRESET
TUNING steps.
11
RECEIVING RDS STATIONS (U.K. and Europe models only)
RDS (Radio Data System) is a data transmission system gradually being introduced by FM stations in many countries. Stations
using this system transmit an inaudible stream of data in addition to the normal radio signal.
RDS data contains various information, such as AF (Alternative Frequencies for the same program station), PI (Program
Identification), PS (Program Service station name), PTY (Program Type name), etc.
RDS function is carried out among the network stations.
* This unit utilizes AF, PI, PS and PTY to receive RDS broadcast stations.
Displaying RDS data
This unit can be turned into the following two modes to display RDS data.
PS (Program Service station name) mode:
Displays the name of the RDS station now being received instead of the frequency.
BBC R3
PTY (Program Type name) mode:
Displays the program type of the RDS station now being received. There are 15 program types to classify RDS stations as follows.
NEWS
AFFAIRS
INFO
SPORT
EDUCATE
DRAMA
News:
Short accounts of facts, events and publicly
expressed views, reportage and actuality.
Current affairs:
Topical program expanding or enlarging
upon the news, generally in different
presentation style or concept, including
documentary debate, or analysis
Information:
Program whose purpose is to impart advice
in the widest sense, including meteorological
reports and forecasts, consumer affairs,
medical help, etc.
VARIED
POP M
ROCK M
Sport:
Program concerned with any aspect of sport.
MOR M
Education:
Program intended primarily to educate, of
which the formal element is fundamental.
Varied:
Used for mainly speech-based programs
usually of light-entertainment nature, not
covered by above categories. Examples are:
quizzes, panel games, personality interviews,
comedy and satire.
Pop:
Commercial music, which would generally be
considered to be of current popular appeal,
often featuring in current or recent record
sales charts.
Rock:
Contemporary modern music, usually written
and performed by young musicians.
M.O.R.:
(Middle of the Road Music). Common term to
describe music considered to be “easylistening”, as opposed to Pop, Rock or
Classical. Music in this category is often but
not always, vocal, and usually of short
duration (<5 min.)
Light classics:
Classical Musical for general, rather than
specialist appreciation. Examples of music in
this category are instrumental music, and
vocal or choral works.
Drama:
All radio plays and serials.
LIGHT M
Culture:
Programs concerned with any aspect of
national or regional culture, including
religious affairs, philosophy, social science,
language, theatre, etc.
of major orchestral works,
CLASSICS Performances
symphonies, chamber music etc., and
Serious classics:
CULTURE
SCIENCE
12
Science:
Programs about the natural sciences and
technology.
including Grand Opera.
OTHER M
Other music:
Musical styles not fitting into any of the
above categories. Particularly used for
specialist music, of which Jazz, Rhythm &
Blues, Folk, Country, and Reggae are
examples.
English
To turn the unit into the PS mode or PTY mode
Press the FREQ/PS/PTY button. Whenever pressed, the mode changes into the PS mode, PTY mode and returns to usual mode in
turn.
* When an RDS station is received, the display is automatically turned into the PS mode. Do not press the FREQ/PS/PTY button
until the display is turned into the PS mode. If the button is pressed before the display mode is changed, it may occur that “NO
PS” flashes on the display. This is because the unit has not received all of the RDS data on the station yet.
PS mode
The name of the station being received is displayed.
If the station is not an RDS station, “NO PS” flashes on the
display and then returns to usual mode.
PTY mode
A program type for the station being received is displayed.
If the RDS station does not employ the PTY data service,
“NO PTY” flashes on the display and then returns to the PS
mode.
If the station is not an RDS station, “NO PTY” flashes on the
display and then returns to usual mode.
Usual mode
The frequency of the station being received is displayed.
PS/PTY/SEEK
FREQ/PS/PTY
SHIFT/
EDIT
ENTER/
KEY MODE
Note
When PS or PTY data reception is not possible due to poor reception conditions, “NO PS” or “NO PTY” flashes on the display in
each mode. In such a case, press the TUNING MODE button so that “AUTO” goes off from the display. Though the reception
mode is changed to monaural by this operation, when you changes to the PS or PTY mode, PS or PTY data may be displayed.
13
Calling a preset RDS station by the station name (PS SEEK)
You can call a desired RDS station stored in this unit by only inputting the name of the station in the PS mode. By this operation,
this unit searches all preset stations for the station. You do not have to input a full name, even only the first letter can be used for
calling. As many as 8 letters and/or numerals can be selected for inputting a name.
1
2 7
4, 8
3, 5
FM/AM
1
2
6
7
Turn the unit into the PS mode.
SHIFT/
EDIT
ENTER/
KEY MODE
A station name is
displayed or “NO PS”
flashes.
* If “NO PS” flashes, proceed to the next step while flashing.
If “NO PS” disappears before you proceed to the next step,
press the FREQ/PS/PTY button again.
3
When inputting the name is finished, press the
ENTER/KEY MODE button.
PS/PTY/SEEK
PS/PTY/SEEK
FREQ/PS/PTY
Repeat steps 4 and 5 for other letters and/or numerals,
if necessary.
FREQ/PS/PTY
8
SHIFT/
EDIT
ENTER
ENTER/
KEY MODE
The name is
illuminated.
PRESET STATIONS
DOWN
UP
Press once.
PS/PTY/SEEK
TUNING
FREQ/PS/PTY
SHIFT/
EDIT
ENTER/
KEY MODE
Flashes
4
Select the first letter or numeral of the station name.
PRESET STATIONS
DOWN
UP
* By pressing the TUNING UP or DOWN button repeatedly or
by pressing and holding either of them, the display will
change letters and numerals in sequence.
* If you will not input the second letter, skip to step 7.
When the first letter or numeral of the station name
appears, press the SHIFT/EDIT button to proceed to the
selection of the next letter or numeral.
PS/PTY/SEEK
FREQ/PS/PTY
14
SHIFT/
EDIT
You do not have to input a full name for searching
for the station
You may input only the first letter of the station name. If doing
so, you can skip steps 5 and 6. In step 8, the unit searches
for and calls a nearest station which has the letter you input. If
the station is not the desired one, press the TUNING UP or
DOWN button again. The unit will begin searching for another
station which has the same letter.
TUNING
5
The unit begins searching for the station, and it is
continued until the station is found.
ENTER/
KEY MODE
“A” will flash on the second
letter or numeral position.
To cancel this function
Press the AF, FREQ/PS/PTY, SHIFT/EDIT, ENTER/KEY
MODE, FM/AM or MEMORY button.
Note
This function is not useful for calling a station with weak
signals which cannot be received by the automatic tuning
method.
English
Calling a preset RDS station by the program type (PTY SEEK)
By designating a program type, the unit automatically searches all preset stations for RDS stations of that program type.
* There are 15 program types to classify RDS stations. For details, refer to page 12.
3, 5
1 4
2
1
Turn the unit into the PTY mode.
PS/PTY/SEEK
FREQ/PS/PTY
SHIFT/
EDIT
Press once or twice
until a program type is
displayed or “NO PTY”
flashes.
ENTER/
KEY MODE
4
When the desired program type appears, press the
ENTER/KEY MODE button.
PS/PTY/SEEK
FREQ/PS/PTY
SHIFT/
EDIT
ENTER
ENTER/
KEY MODE
Flashes.
* If “NO PTY” flashes, proceed to the next step while
flashing. If “NO PTY” disappears before you proceed to the
next step, press the FREQ/PS/PTY button once or twice.
2
5
PRESET STATIONS
DOWN
UP
Press once.
PS/PTY/SEEK
TUNING
FREQ/PS/PTY
SHIFT/
EDIT
ENTER/
KEY MODE
The program type of the station now being
received or “NEWS” flashes on the display.
3
Select the desired program type.
PRESET STATIONS
DOWN
UP
TUNING
* By pressing the TUNING UP or DOWN button repeatedly or
by pressing and holding either of them, the display will
change program types in sequence.
The unit begins searching all preset stations, and calls a
station of the program type if such a station is found.
* When the TUNING UP button is pressed, the search is
performed from “A1” toward higher numbers of the preset
stations (A1, A2 ... A8, B1, B2, ...). If, however, “A3” is
currently being called for example, the search begins from
the next station “A4”.
When the TUNING DOWN button is pressed, the search
is performed in reverse order.
If the called station is not the desired one, press the
TUNING UP or DOWN button again to search for another
station of the same program type.
To cancel this function
Press the AF, FREQ/PS/PTY, SHIFT/EDIT, ENTER/KEY
MODE, FM/AM or MEMORY button.
15
Calling the best quality RDS station which broadcasts the
same program (AF SEEK)
This function automatically searches for and calls another RDS station of the best reception quality which broadcasts the same
program now you are listening to.
This function utilizes AF (Alternative Frequencies for the same program station) and PI (Program Identification) of RDS data service.
The search is carried out among the RDS network stations.
2, 3
1
2
Tune to a desired RDS station.
* Wait for about 10 seconds before proceeding to the
next step. This allows the unit to search for more
stations.
If desired, you can call the second station by pressing
the AF button.
AF
AF
The unit searches for other stations with the same program.
* If the station is not an RDS station, or there is no other
station with the same program, “NO AF” flashes.
Stations with the same program are all stored and
numbered from the best quality station in sequence.
When the search is finished, the best quality station is
called.
16
3
Whenever the AF button is pressed, stored stations are
called in sequence.
When pressed after the last station is selected, the first one
is restored.
To cancel this function
Press a button other than the AF button.
All of the stored stations will be also cleared.
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple
measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and
contact your authorized YAMAHA dealer or service center for help.
SYMPTOM
FM
Crackling sounds from time to time
(especially in weak signal areas).
CAUSE
AM
REMEDY
Ignition noise from passing vehicles.
The FM antenna should be put up as high
as possible, away from the road, and a
coaxial cable used.
Noise from thermostats or other electrical
equipment.
Attach a noise suppressor to the equipment
causing the noise.
FM stereo reception is noisy.
Because of the characteristics of FM stereo
broadcasts, this is limited to cases where
the transmitter is far away or the antenna
input is poor.
Check the antenna connections.
Try using a high quality directional FM
antenna.
Set the TUNING MODE button to the
manual tuning mode.
The “ST” indicator flickers and reception
is noisy.
Insufficient antenna input.
Use an antenna appropriate for the
reception condition in your area.
Not tuned correctly.
Tune again.
There is distortion and clear reception
cannot be obtained even with a good FM
antenna.
There is multipath interference.
Adjust antenna placement to eliminate multipath interference.
No stereo effect even with a stereo
broadcast.
The TUNING MODE button is set to the
manual tuning mode.
Set the button properly.
A desired station cannot be tuned in with
Automatic tuning.
The station is too weak.
Use the manual tuning mode.
Use a high quality directional FM antenna.
Previously preset stations can no longer
be tuned in.
The tuner has been unplugged for a long
period.
Repeat the presetting procedure.
Insufficient sensitivity.
Weak signal or loose antenna connections.
Tighten the AM loop antenna connections
and rotate it for best reception.
A desired station cannot be tuned in with
Automatic tuning.
English
TROUBLESHOOTING
Use the manual tuning mode.
There are continuous crackling and
hissing noises.
These noises result from lightning,
fluorescent lamps, motors, thermostats and
other electrical equipment.
Use an outdoor antenna and a ground wire.
This will help somewhat but it is difficult to
eliminate all noises.
There are buzzing and whining noises
(especially in the evening).
Another station is interfering with the
received station.
This is impossible to remedy.
A television set is being used nearby.
Relocate this unit away from the TV.
17
SPECIFICATIONS
FM SECTION
AM SECTION
Tuning Range ...................................................87.5 to 108 MHz
Tuning Range
[General model] .........................................530 to 1,710 kHz
[U.K. and Europe models]..........................531 to 1,611 kHz
50 dB Quieting Sensitivity (IHF) [Except Europe model]
75 ohms Mono ........................................1.55 µV (15.1 dBf)
75 ohms Stereo ..........................................21 µV (37.7 dBf)
Usable Sensitivity ........................................................100 µV/m
Usable Sensitivity [Europe model] (DIN)
75 ohms Mono (S/N 26 dB) ........................................0.9 µV
75 ohms Stereo (S/N 46 dB)........................................24 µV
Selectivity ..........................................................................32 dB
Image Response Ratio
[Except Europe model] ................................................45 dB
[Europe model] ............................................................80 dB
Image Response Ratio ......................................................40 dB
IF Response Ratio
[Except Europe model] ................................................70 dB
[Europe model] ............................................................80 dB
Harmonic Distortion; 400 Hz...............................................0.3%
Spurious Response Ratio..................................................70 dB
Output Level/Impedance (Fixed)
FM (100 % mod. 1 kHz)
[Except Europe model] ........................550 mV/2.2 k-ohms
[Europe model (40 kHz Dev.)] .............400 mV/2.2 k-ohms
AM (30% mod. 400 Hz)..........................150 mV/2.2 k-ohms
AM Suppression Ratio.......................................................55 dB
Capture Ratio ...................................................................1.5 dB
Alternate Channel Selectivity
[Except Europe model] ................................................85 dB
Selectivity (two signals, 40 kHz Dev., ±300 kHz)
[Europe model only].....................................................70 dB
Signal-to-Noise Ratio
[Except Europe model] (IHF)
Mono..........................................................................80 dB
Stereo ........................................................................75 dB
[Europe model] (DIN-Unweighted)
Mono (40 kHz Dev.)...................................................74 dB
Stereo (40 kHz Dev.) ................................................69 dB
Harmonic Distortion (1 kHz)
[Except Europe model]
Mono/Stereo ......................................................0.1%/0.2%
[Europe model (40 kHz Dev.)]
Mono/Stereo ......................................................0.1%/0.2%
Stereo Separation (1 kHz)
[Except Europe model] ................................................50 dB
[Europe model (40 kHz Dev.)] .....................................50 dB
Frequency Response
30 Hz to 15 kHz....................................................0±0.5 dB
18
Signal-to-Noise Ratio.........................................................50 dB
Spurious Response Ratio..................................................50 dB
AUDIO SECTION
GENERAL
Power Supply
[Europe model] ..................................................230V, 50 Hz
[U.K. model].......................................................240V, 50 Hz
[General model] ......................110-120/220-240V, 50/60 Hz
Power Consumption
[Except General model] .................................................10W
[General model] ...............................................................7W
Dimensions (W x H x D) ............................280 x 82.5 x 360 mm
(11” x 3-1/4” x 14-3/16”)
Weight ...........................................................3 kg (6 lbs. 10 oz.)
Accessories .............................................Audio connection cord
AM loop antenna
Indoor FM antenna
* Specifications subject to change without notice.
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, D-2084 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
ELECTRONIQUE FRANCE S.A. 17 RUE DES CAMPANULES, LOGNES 77321 MARNE LA VALLEE CEDEX 2, FRANCE
ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising