G DVD AUDIO/VIDEO SA-CD PLAYER LECTEUR DVD AUDIO/VIDEO SA-CD DVD-S1800 HDMI STANDBY ON AUDIO DIRECT CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. CAUTION AVERTISSEMENT L’utilisation de commandes et l’emploi de réglages ou de méthodes autres que ceux décrits ci-dessous, peuvent entraîner une exposition à un rayonnement dangereux. SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING. UNDGÅ UDSÆTTELSE FOR STRÅLING. VORSICHT Die Verwendung von Bedienelementen oder die Einstellung bzw. die Ausführung von anderen als in dieser Anleitung beschriebenen Vorgängen kann zu Gefährdung durch gefährliche Strahlung führen. OBSERVERA Användning av reglage eller justeringar eller utförande av åtgärder på annat sätt än så som beskrivs häri kan resultera i farlig strålning. ATTENZIONE L’uso di controlli, regolazioni, operazioni o procedure non specificati in questo manuale possono risultare in esposizione a radiazioni pericolose. PRECAUCIÓN El uso de los controles, los ajustes o los procedimientos que no se especifican enste manual pueden causar una exposición peligrosa a la radiación. LET OP Gebruik van bedieningsorganen, instellingen of procedures anders dan beschreven in dit document kan leiden tot blootstelling aan gevaarlijke stralen. VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM. ADVARSEL ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES. UNNGÅ EKSPONERING FOR STRÅLEN. VARNING SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN. VARO! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA NÄKYMÄTTÖMÄLLE LASER SÄ TEILYLLE. ÄLÄ KATSO SÄTEESEEN. VORSICHT SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET. NICHT DEM STRAHL AUSSETSEN. DANGER VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM. ATTENTION RAYONNEMENT LASER VISIBLE ET INVISIBLE EN CAS D’OUVERTURE. EXPOSITION DANGEREUSE AU FAISCEAU. OSTRZEŻENIE WIDZIALNE I NIEWIDZIALNE PROMIENIOWANIE LASEROWE PO OTWARCIU. UNIKAĆ NARAŻENIA NA WIĄZKĘ LASEROWĄ. OSTRZEŻENIE Używanie regulatorów i nastawień w inny sposób lub wykonywanie procedur innych niż tutaj podane może być przyczyną niebezpiecznego promieniowania. CAUTION-VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS. ii En CAUTION: READ THIS BEFORE OPERATING THIS UNIT. CAUTION: READ THIS BEFORE OPERATING THIS UNIT. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. Install this unit in a well ventilated, cool, dry, clean place — away from direct sunlight, heat sources, vibration, dust, moisture, or cold. In a cabinet, allow about 2.5 cm (1 inch) of free space all around this unit for adequate ventilation. Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. Do not expose this unit to sudden temperature changes from cold to hot, nor locate this unit in an environment with high humidity (i.e., a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury. Avoid installing this unit in a location where foreign objects may fall onto this unit or where this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place: – Other components, as they may cause damage and/ or discoloration on the surface of this unit. – Burning objects (i.e., candles), as they may cause fire, damage to this unit, and/or personal injury. – Containers with liquid in them, as they may fall, spilling the liquid and causing an electrical shock to the user and/or damage to this unit. Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury. Do not plug in this unit to a wall outlet until all connections are complete. Do not operate this unit upside-down. It may overheat, possibly causing damage. Do not use excessive force on switches, knobs and/or cords. When disconnecting the power cord from the wall outlet, grasp the plug; do not pull the cord. Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. Use only the voltage specified on this unit. Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. Yamaha will not be held responsible for any damage resulting from use of this unit with a voltage other than as specified. Do not attempt to modify or fix this unit. Contact qualified Yamaha service personnel when any service is needed. The cabinet should never be opened for any reason. When not planning to use this unit for long periods of time (i.e., vacation), disconnect the AC power plug from the wall outlet. iii En 15 Be sure to read the “TROUBLESHOOTING” section on common operating errors before concluding that this unit is faulty. 16 Before moving this unit, press STANDBY/ON to set the unit in standby mode, then disconnect the AC power plug from the wall outlet. 17 Install this unit near the AC outlet and where the AC power plug can be reached easily. 18 The batteries shall not be exposed to excessive heat such as sunshine, fire or the like. The unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. LASER SAFETY This unit employs a laser. Due to possible eye injury, only a qualified service person should remove the cover or attempt to service this device. DANGER This unit emits visible laser radiation when open. Avoid direct eye exposure to beam. When this unit is plugged into a wall outlet, do not place your eyes close to the opening of the disc tray and other openings or look inside. This symbol mark is according to the EU directive 2002/96/EC. This symbol mark means that electrical and electronic equipment, at their end-oflife, should be disposed of separately from your household waste. Please act according to your local rules and do not dispose of your old products with your normal household waste. INTRODUCTION 3 Playable disc formats ................................... DVD region codes .............................................. Patent information ........................................ Cleaning discs .............................................. Supplied accessories ................................... FUNCTIONAL OVERVIEW 5 Front panel .................................................... Front panel display ....................................... Rear panel ..................................................... Remote control ............................................. CONNECTIONS General notes on connections .................. Audio connections ..................................... Connecting a stereo amplifier ........................... Connecting an AV receiver with 6ch/ multi-channel input ....................................... Video connections ...................................... HDMI connection ........................................ Connecting the power cable ...................... GETTING STARTED Step 1: Inserting batteries into the remote control ................................... Using the remote control .................................. Step 2: Turning on the power .................... Step 3: Setting a TV type ............................ Step 4: Setting a language preference ..... Setting the OSD (On-Screen Display) language ........................................................ Setting the audio, subtitle and disc menu languages ..................................... 3 3 4 4 4 5 6 7 8 10 10 10 10 10 11 12 14 15 15 15 15 16 17 17 17 DISC OPERATION English CONTENTS 18 Basic operation ........................................... 18 Pausing playback ............................................... 18 Selecting a track/chapter ................................... 18 Searching backward/forward ............................ 19 Repeat playback .......................................... 19 Repeating playback ........................................... 19 Repeating a section (except DVD-Audio/MP3/WMA/JPEG) ...... 19 Random playback (except DVD/SA-CD) ................................ 19 Program playback (CD) .............................. 20 Disc menu operation (DVD/VCD/SVCD) ..................................... 20 Using the DVD menu ........................................ 20 Using the Video CD playback control (PBC) menu (VCD/SVCD) ...................................... 21 On-screen display (OSD) menu (DVD/VCD/SVCD/SA-CD) ........................ 21 Using the OSD menu (DVD/VCD/SVCD/CD) ............................... 21 Displaying text information (SA-CD) ............... 22 Picture Setting menu (DVD/VCD/SVCD) ..................................... 22 Adjusting picture settings .................................. 22 Zooming pictures (DVD-Video/VCD/SVCD/DivX®/JPEG) .... 23 Viewing angles (DVD-Video) ...................... 23 Audio and Subtitle languages (DVD-Video/VCD) ..................................... 24 Selecting an audio language .............................. 24 Selecting a subtitle language (DVD-Video) ................................................ 24 DivX® external subtitle files ....................... 24 Changing pages (DVD-Audio) .................... 24 Group/File selection (DVD-Audio/DivX®/ MP3/WMA/Kodak picture CD) ................. 25 Selecting a group (DVD-Audio) ....................... 25 Selecting a file in a folder (DivX®/MP3/WMA/Kodak picture CD) ...... 25 Bonus group playback (DVD-Audio) ............................................. 25 Changing the playback area and layer (SA-CD) .................................... 25 Multimedia file playback (MP3/WMA/DivX®/JPEG) ......................... 26 Displaying the thumbnail screen (JPEG) .......... 26 Rotating pictures (JPEG) ................................... 26 Continued 1 En CONTENTS SETUP MENU 27 Menu overview ............................................ 27 Setup menu operation ................................ 28 General setup menu ................................... 29 Selecting DVD-Audio mode ............................. 29 Selecting SA-CD mode ..................................... 29 Setting the OSD language ................................. 29 Restricting playback with parental control ....... 29 Changing the parental password ....................... 29 Setting the screen saver ..................................... 30 Setting the auto power function ........................ 30 Setting the sleep timer ....................................... 30 Resetting the system ......................................... 30 Displaying the DivX® VOD registration code ............................................ 30 Audio setup menu ...................................... 31 Setting the analog output .................................. 31 Setting the digital output ................................... 31 Setting the LPCM output .................................. 31 Setting the night listening mode ....................... 31 Speaker setup menu ................................... 32 Setting speaker sizes ......................................... 32 Setting speaker distances .................................. 32 Setting speaker levels ........................................ 33 Setting the SA-CD configuration ...................... 33 Video setup menu ....................................... 34 Setting the TV display ...................................... 34 Setting the TV type ........................................... 34 Selecting the wide screen format ...................... 34 Selecting the black level (U.S.A. and Canada models only) ................ 35 Selecting the closed caption (U.S.A. and Canada models only) ................ 35 Setting the still mode ........................................ 35 Selecting the scan function ............................... 35 Switching the SCART video out (U.K., Europe, and Russia models only) ...... 36 HDMI setup menu ....................................... 36 Setting the HDMI video .................................... 36 Selecting the DVI output range ........................ 37 Setting the HDMI audio .................................... 37 DISC setup menu ........................................ 37 Selecting the default audio/subtitle/ DVD menu language .................................... 37 Selecting an angle mark display ....................... 37 Selecting the PBC (playback control) function ......................................................... 38 Setting the duration for a slide show ................ 38 2 En LANGUAGE CODE LIST 39 TROUBLESHOOTING 40 GLOSSARY 42 SPECIFICATIONS 44 INTRODUCTION Thank you for purchasing this unit. This Owner’s Manual explains the basic operation of this unit. • Illustrations in this manual are based on the U.K., Europe, and Russia models unless otherwise specified. • Notes contain important information about safety and operating instructions. • y indicates a tip for your operation. • This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In case of differences between the manual and the product, the product has priority. Playable disc formats • This unit is designed for use with the following discs: DVD-Video, DVD-Audio, DVD-R, DVD-RW, DVD+R, DVD+RW, DVD+R DL, Video CD, Super Video CD, Super Audio CD (SA-CD), Audio CD, CD-R and CD-RW. English INTRODUCTION Notes • CD-R(W), DVD-R(W) and DVD+R(W) cannot be played unless finalized. • Copyright-protected WMA files cannot be played with this unit. • This unit supports JPEG files of 2848 x 2136 pixels in size. • Some discs cannot be played depending on the recording conditions, such as the PC environment and application software. The characteristics and condition of some discs; materials, scratches, curvature, etc., may result in playback failure. • Be sure to use only CD-R(W), DVD-R(W) and DVD+R(W) discs made by reliable manufacturers. • Do not use any non-standard shaped discs (heart-shaped, etc.). • Do not use discs with tape, seals, or paste on their surface. Doing so may damage this unit. • Do not use discs affixed with labels printed by a commercially available label printer. DVD region codes This unit is designed to support the region management system. Check the regional code number on the DVD disc package. If the number does not match the region code of this unit (see the table below or the back of this unit), this unit may be unable to play the disc. Destination • This unit can play: – MP3, WMA (except copyright-protected WMA) and picture (Kodak, JPEG) files recorded on CD-R(W)/ DVD-R(W)/DVD+R(W) – JPEG/ISO 9660 format – Maximum 14 character display – DivX® disc on CD-R(W)/DVD-R(W)/DVD+R(W) – Official DivX® Certified product – Plays all versions of DivX® video (including DivX® 6) with standard playback of DivX® media files Region code of this unit Playable discs U.S.A. Canada 1 1 ALL U.K. Europe 2 2 ALL Asia Korea 3 3 ALL 5 5 ALL Russia 3 En INTRODUCTION Patent information – Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. Cleaning discs • When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the center out. Do not wipe in a circular motion. • Do not use solvents such as benzine, thinner, commercially available cleaners, or antistatic spray intended for analog records. “DTS” and “DTS Digital Surround” are registered trademarks of DTS, Inc. Supplied accessories DivX, DivX Certified, and associated logos are trademarks of DivX, Inc. and are used under license. Check your package to make sure it contains the following items: Remote control “DCDi” is a trademark of Faroudja, a division of Genesis Microchip, Inc. Batteries (x2) (AAA, R03, UM-4) POWER DIMMER HDMI AUDIO DIRECT STANDBY GROUP MULTI 2CH PAGE PROG “HDMI”, the “HDMI” logo and “High Definition Multimedia Interface” are trademarks or registered trademark of HDMI Licensing LLC. RANDOM A B CLEAR ENTER SETUP SLOW SEARCH STOP This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. 4 En Audio pin cable REPEAT PAUSE PLAY SKIP TOP MENU ON SCREEN Video pin cable ENTER MENU RETURN SUBTITLE AUDIO ANGLE ZOOM Power cable FUNCTIONAL OVERVIEW English FUNCTIONAL OVERVIEW Front panel 1 HDMI AUDIO DIRECT STANDBY ON 2 3 4 5 6 7 8 9 0 Disc tray Load a disc in the disc tray. 6 2 STANDBY/ON Turns on this unit or sets it to the standby mode. 7 b/w Searches backward.* Moves to the previous chapter or track. 3 HDMI indicator Lights up green when an HDMI component is recognized by this unit and the HDMI mode is set to on. Lights up orange when no HDMI component is recognized by this unit while the HDMI mode is set to on. 8 f/a Searches forward.* Moves to the next chapter or track. 9 p/e Starts or pauses playback. s Stops playback. 1 Opens or closes the disc tray. 4 AUDIO DIRECT indicator Lights up when you select the AUDIO DIRECT mode by pressing AUDIO DIRECT on the remote control. 0 5 Front panel display Displays playback information or settings. * Press and hold the button for about two seconds. 5 En FUNCTIONAL OVERVIEW Front panel display 1 2 SVCD WMA P.SCAN TITLE GROUP CHP/ TRK MP3 JPEG DVD AUDIO SA-CD DivX 3 4 D 6 5 2 MULTI D.MIX PROG. RANDOM ALL A B 7 1 P.SCAN indicator Lights up when the progressive scan function is activated. 5 D.MIX indicator (DVD-Audio only) Lights up when playing the disc that allows down mixing of the multi-channel audio source. 2 Playback mode indicators Display the icon for the selected playback mode. 6 Disc indicators Display the icon for the disc type. 3 Decoder indicators Display the icon for the selected internal decoder. 7 Information display Displays various information such as a title/chapter/ track number or elapsed playing time. 4 MULTI indicator Lights up when playing the multi-channel audio source. y You can adjust the brightness of the front panel display using DIMMER on the remote control. 6 En FUNCTIONAL OVERVIEW 1 English Rear panel 2 3 4 5 6 7 MAINS PR / CR CENTER L COAXIAL VIDEO IN L AV PB / CB Y R MIXED 2CH FRONT R SUBWOOFER SURROUND AUDIO OUT 8 OPTICAL DIGITAL OUT ON OFF RS 232C S VIDEO HDMI REMOTE CONTROL 9 COMPONENT VIDEO OUT 0 q w (U.K., Europe, and Russia models) 1 AUDIO OUT (6ch discrete) jacks Connect to the 6ch input jacks of your AV receiver. 7 MAINS Connect the supplied power cable. 2 DIGITAL (COAXIAL) jack Connect to the coaxial input jack of your AV receiver. 8 AUDIO OUT (MIXED 2CH) jacks Connect to the audio input jacks of your AV receiver or stereo system. 3 REMOTE CONTROL (IN/OUT) connectors Use in custom installations to transmit remote control signals via cable connections. 9 DIGITAL (OPTICAL) jack Connect to the optical input jack of your AV receiver. 0 HDMI jack Connect to the HDMI input jack of your HDMI component. q VIDEO OUT (S VIDEO) jack Connect to the S-video input jack of your AV receiver. 4 5 6 REMOTE CONTROL (RS-232C) terminal (U.S.A., Canada, U.K., Europe, and Russia models only) Use as an expansion terminal for commercial use. Consult your dealer for details. AV terminal (U.K., Europe, and Russia models only) Connect to SCART input terminal of your TV. w VIDEO OUT (COMPONENT) jacks Connect to the component input jacks of your AV receiver. VIDEO OUT (VIDEO) jack Connect to the composite video input jack of your AV receiver. ■ Remote control connectors and RS-232C terminal The REMOTE CONTROL (IN/OUT) connectors and the REMOTE CONTROL (RS-232C) terminal are used in custom installation. Keep the RS-232C switch set to OFF and do not connect any cables to these connectors during normal use. Caution: Do not touch the inner pins of the jacks on the rear panel of this unit. Electrostatic discharge may cause permanent damage to this unit. 7 En FUNCTIONAL OVERVIEW Remote control 1 DIMMER Selects from three different levels of brightness for the front panel display: bright, dim and auto. For auto setting, brightness is automatically set to low only during playback. 2 HDMI Switches between the HDMI resolution settings or turns off the HDMI mode (see page 36). POWER 1 2 3 4 DIMMER HDMI AUDIO DIRECT STANDBY GROUP MULTI 2CH PAGE y u i o y PROG • You can select the HDMI resolution by pressing HDMI on the remote control repeatedly or by using the HDMI Video setup menu. • If you press HDMI on the remote control once, the currently selected resolution setting is displayed in the top left corner of the display and in the front panel display. p RANDOM a 5 REPEAT A B 6 7 CLEAR ENTER SETUP SLOW SEARCH STOP PAUSE PLAY h 8 9 0 3 GROUP Selects the DVD-Audio group (see page 25). 4 PAGE (+/–) Selects the DVD-Audio still picture (see page 24). 5 Numeric buttons (0-9) Select numbered items in the currently displayed menu. 6 CLEAR Clear the mode or setting (see page 20). 7 SETUP Accesses or exits from the setup menu of this unit (see page 28). 8 STOP ( 7) Stops playback (see page 18). 9 PAUSE ( 8) Pauses playback temporarily (see page 18). Frame-by-frame playback (see page 18). 0 SKIP (l22 / 33l) Moves to the previous/next chapter or track. q TOP MENU Displays the top-level disc menu. SKIP TOP MENU q w ON SCREEN j ENTER MENU RETURN k e SUBTITLE AUDIO ANGLE ZOOM r t s d f g l ; y The title menu is displayed for discs with the title menu. 8 En FUNCTIONAL OVERVIEW w Cursors ( / / / ) Selects an item in the currently displayed menu. r t A-B Repeats a specific segment (see page 19). ENTER Confirms the menu selection. f ENTER Confirms the menu selection. MENU Accesses the menu of a disc (see page 20). g SLOW / SEARCH (22 / 33) Searches backward or forward (see page 19). SUBTITLE Selects the subtitle language (see page 24). h PLAY ( 3) Starts playback (see page 18). AUDIO Selects the audio language or format (see page 24). j ON SCREEN Accesses or exit from the on-screen display (OSD) menu of this unit (see page 21). Press twice during playback to access the Picture Setting menu (see page 22). k RETURN Returns to the previous setup menu. l ZOOM Enlarges the video image (see page 23). ; ANGLE Selects the DVD camera angle (see page 23). y POWER ( l ) Turns on this unit (see page 15). u STANDBY ( ) Sets this unit to the standby mode (see page 15). i AUDIO DIRECT Turns off the video output during audio disc playback in order to improve audio quality. Press again to turn on the video output. This function is not available when an HDMI component is recognized by this unit. In the AUDIO DIRECT mode, the front panel display goes out. Once this unit is turned off, the AUDIO DIRECT mode is cleared (only when an SA-CD disc is played back, the mode is cleared if the disc tray is opened/closed). o MULTI / 2CH Selects a sound mode: Stereo or Multi-channel. Changes the SA-CD playback area (see page 25). p PROG Accesses the program setup menu to program disc tracks or exit from its menu (see page 20). a RANDOM Plays tracks in random order (see page 19). s REPEAT Repeats the chapter, track, title, group or disc (see page 19). English e d y Two ENTER buttons (w and f) act in the same way. 9 En CONNECTIONS CONNECTIONS General notes on connections Be sure to turn off this unit and unplug the power supply cable, before you make or change connections. • Depending on the component you want to connect, there are various ways to make connections. Possible connections are described below. • Refer to the manuals supplied with your other components as necessary to make the best connections. • Do not connect this unit via your VCR. The video quality could be distorted by the copy protection system. • Do not connect the audio out jack of this unit to the phono in jack of your audio system. Connecting an AV receiver with 6ch/ multi-channel input ■ Analog connections If you want to reproduce multi-channel Super Audio CD (SA-CD) and DVD-Audio, connect AUDIO OUT (6ch discrete) jacks of this unit to the corresponding input jacks of your AV receiver using commercially available audio pin cables. CENTER L COAXIAL IN L AV Audio connections R MIXED 2CH FRONT R SUBWOOFER SURROUND AUDIO OUT OPTICAL OUT ON DIGITAL OFF RS 232C This unit (U.K., Europe, and Russia models) Connecting a stereo amplifier Connect AUDIO OUT (MIXED 2CH) jacks of this unit to the corresponding input jacks of your audio component (such as a stereo amplifier) using the supplied audio pin cable. You can connect a subwoofer to the SUBWOOFER jack. FRONT R L CENTER SUBWOOFER SURROUND R L AV receiver This unit (U.K., Europe, and Russia models) Speakers CENTER COAXIAL IN L L AV R MIXED 2CH R FRONT SUBWOOFER AUDIO OUT SURROUND OPTICAL DIGITAL OUT OFF ON RS 232C HDMI REMOTE CONTROL Audio pin cable (supplied) Stereo amplifier CD / DVD R L Subwoofer Left speaker 10 En Right speaker HDMI REMOTE CONTROL This unit has digital coaxial, digital optical, analog 6ch discrete, and analog mixed 2ch output jacks. Connection depends on the availability of audio jacks on your component. CONNECTIONS ■ Digital connections CENTER COAXIAL L FRONT SUBWOOFER R SURROUND AUDIO OUT OPTICAL This unit has SCART, composite video, S-video, and component video output jacks. If your AV receiver has video output jacks, connect your receiver and then your TV so that you can use one TV for several different video sources (LD, VCR, etc.) by simply switching the input source selector on your receiver. Use the one that corresponds to the input jacks on the component to be connected. IN L This unit (U.K., Europe, and Russia models) AV R MIXED 2CH Video connections OUT DIGITAL ON OFF RS 232C HDMI REMOTE CONTROL PR / CR VIDEO AV This unit (U.K., Europe, and Russia models) PB / CB Y RS 232C S VIDEO HDMI ONTROL <A> OPTICAL IN <B> COAXIAL IN COMPONENT VIDEO OUT Video pin cable (supplied) <A> <B> <C> <D> AV receiver VIDEO IN S-VIDEO IN PB/CB PR/CR Y COMPONENT VIDEO IN Speakers AV receiver Notes • If you make a connection with <A> or <B>, set [Digital Out] to [All] (see “Setting the digital output” on page 31). • If the audio format of the digital output does not match the capabilities of your receiver, the receiver produces a distorted sound or no sound at all. Make sure to select the appropriate audio format from the menu screen on the disc. Pressing AUDIO on the remote control once or more may change not only the audio languages but also the audio format. • SA-CD audio signals are not output from DIGITAL (COAXIAL/OPTICAL) jacks. • If you want to enjoy Dolby Digital, DTS, and MPEG formats, you must connect this unit to an AV receiver that supports these formats. VIDEO OUT S VIDEO OUT COMPONENT VIDEO OUT VIDEO IN S VIDEO IN COMPONENT VIDEO IN TV 11 En English If you want to use the Dolby Digital, DTS, or MPEG function on your AV receiver, connect DIGITAL (OPTICAL) <A> or DIGITAL (COAXIAL) <B> jack of this unit to the corresponding input jacks of your AV receiver using a commercially available digital optical or digital coaxial cable. CONNECTIONS ■ Composite video jack <A> Connect VIDEO OUT (VIDEO) jack of this unit to the video input jack of your AV receiver, and then to that of your TV using the supplied video pin cable. ■ S-video jack <B> S-video connections achieve a clearer picture than composite video connections by transmitting video signals on separate wires for luminance (Y) and chrominance (C). Connect VIDEO OUT (S VIDEO) jack of this unit to S-video input jack of your AV receiver, and then to that of your TV using a commercially available S-video cable. HDMI connection HDMI (High-Definition Multimedia Interface) provides high quality digital audio and video on a single connection. Connect the HDMI jack of this unit to an HDMI input jack of your AV receiver, and then to that of your TV using a commercially available HDMI cable. If your receiver does not have an HDMI input jack, you can achieve a better video image by connecting the HDMI jack of this unit directly to the HDMI input jack of your TV. ■ Component video jacks <C> Component video connections achieve higher fidelity color reproduction than S-video connections by transmitting video signals on separate wires for luminance (Y: green) and chrominance (PB: blue, PR: red). Connect VIDEO OUT (COMPONENT) jacks of this unit to the component input jacks of your AV receiver, and then to those of your TV using a commercially available component cable. Observe the color of each jack when you make connections. If your receiver does not have component output jacks, you can achieve a better video image by connecting the component output jacks of this unit directly to the component input jacks of your TV. CENTER COAXIAL L IN L AV R MIXED 2CH FRONT SUBWOOFER AUDIO OUT R SURROUND OPTICAL OUT DIGITAL ON OFF RS 232C HDMI REMOTE CONTROL This unit (U.K., Europe, and Russia models) HDMI IN ■ SCART terminal <D> (U.K., Europe, and Russia models only) AV receiver If your TV has only a terminal for video input, you can connect the TV directly to this unit. Connect AV terminal of this unit to SCART input terminal of your TV using a commercially available SCART cable. HDMI OUT HDMI IN Notes • Ensure that the “TV” indication on SCART cable is connected to the TV set and “DVD” indication on SCART cable is connected to this unit. • S-video signal is not output at AV terminal. See page 36 for SCART video setting. Speakers TV Notes • You need to make appropriate audio connections if the connected component does not input audio signals (see page 10). • This unit is not compatible with HDCP-incompatible HDMI or DVI components. • You need a commercially available HDMI/DVI conversion cable when you connect this unit to other DVI components. In this case, you need to use another audio connection to this connection because the HDMI jack of this unit does not output any audio signals. • Do not disconnect or turn off the power of the HDMI/DVI component connected to the HDMI jack of this unit while data is being transferred. Doing so may disrupt playback or cause noise. y When connecting an HDMI component, refer to the manual supplied with your component. 12 En CONNECTIONS ■ HDMI video output English This unit is compatible with the following video formats: 480p/60 Hz, 576p/50 Hz, 720p/50 Hz, 60 Hz, 1080i/50 Hz, 60 Hz, and 1080p/50 Hz, 60 Hz. Notes • You need to select one of the HDMI resolution settings by pressing HDMI on the remote control repeatedly or by using the HDMI Video setup menu (see page 36). • Depending on the connected DVI component, black and white in the image may not be distinct. In this case, adjust the picture setting of the connected DVI component. ■ HDMI audio output Analog output setting Audio format Dolby Digital DVD-Video DTS MPEG PCM 2ch*4 DVD-Audio CD/MP3/ WMA/DivX® DTS-CD VCD SVCD SA-CD Multi Multi-channel Stereo Multi-channel Stereo Multi-channel Stereo HDMI Audio Auto*1 Dolby Digital DTS MPEG PCM PCM PCM 2ch PCM multi*2 PCM 2ch PCM multi*2 PCM 2ch Multi-channel/Stereo PCM 2ch PCM 2ch Multi-channel PCM (PPCM) multi*2,3 PCM (PPCM) multi*2,3 Stereo PCM (PPCM) 2ch*3 PCM (PPCM) 2ch*3 2ch*4 Multi-channel/Stereo PCM (PPCM) 2ch PCM (PPCM) 2ch 2ch Multi-channel/Stereo PCM 2ch PCM 2ch Multi Stereo Multi-channel/Stereo 2ch Multi-channel/Stereo Multi DTS 2ch Multi-channel/Stereo Multi/2ch Multi-channel/Stereo PCM 2ch PCM 2ch PCM 2ch PCM 2ch PCM multi*2 Multi-channel Stereo Off PCM multi*2 Multi-channel 2ch Off multi*2 MPEG PCM 2ch PCM 2ch – – – *1: If the connected HDMI component does not support bitstream signals (Dolby Digital, DTS, and MPEG), the audio output is automatically changed from bitstream signals to PCM signals. *2: If the HDMI component does not support multi-channel audio signals, the audio output is automatically changed from PCM multi-channel signals to PCM stereo signals and 48 kHz/16 bits signals or less. *3: If the audio source is prohibited from downmixing, the front L/R channel audio and 48 kHz/16-bit signals or less are output instead of downmixed stereo. *4: If the connected component does not support more than 48 kHz, the audio output is automatically changed to 48 kHz/ 16-bit signals or less. Notes • You need to set HDMI Audio (see page 37). • SA-CD signals cannot be output using HDMI. Make an analog connection to listen to SA-CD (see page 10). 13 En CONNECTIONS Connecting the power cable After all other connections are complete, plug the supplied power cable into MAINS of this unit and then plug the power cable to an AC outlet. To an AC outlet MAINS 14 En GETTING STARTED English GETTING STARTED y If the settings you have made are inappropriate, you can always reset all options and your personal settings to the initial factory settings. For details, see “Resetting the system” on page 30. Step 1: Inserting batteries into the remote control Using the remote control Use the remote control within 6 m (20 ft approx.) of this unit and point it toward the remote control sensor. 3 2 1 within 6m (20 ft approx.) 1 Press the part and slide the battery compartment cover off. 2 Insert the two supplied batteries (AAA, R03, UM-4), following the indications (+/–) on the inside of the compartment. 3 Slide the cover back until it snaps into place. Notes • Insert batteries correctly according to the polarity markings (+/–). The batteries inserted in the opposite direction may leak. • Replace the exhausted batteries immediately with new ones to prevent a leakage. • Remove the batteries from the compartment if the remote control is not used for more than a month. • If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. • Do not use old batteries together with new ones. • Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and color. • Dispose of the batteries correctly in accordance with your local regulations. Notes • Do not spill water or other liquids on the remote control. • Do not drop the remote control. • Do not leave or store the remote control in the following types of conditions: – places of high humidity, such as near a bath – places of high temperature, such as near a heater or stove – places of extremely low temperature – dusty places Step 2: Turning on the power 1 Make sure that the power cable is connected to an AC outlet. 2 Turn on your TV and AV receiver. 3 Select the appropriate input source of the AV receiver connected to this unit. Refer to the manual supplied with your AV receiver for details. 4 Press STANDBY/ON on the front panel or POWER ( l ) on the remote control to turn on this unit. ➜ The front panel display lights up. 5 Set the TV to the correct Video IN channel (e.g., EXT1/2, AV1/2, AUDIO/VIDEO, etc. Refer to the manual supplied with your TV for details). ➜ The default screen appears on the TV. 15 En GETTING STARTED 3 Press Step 3: Setting a TV type repeatedly to highlight [TV / Type]. This unit is compatible with both NTSC and PAL video formats. Select the color system that matches your TV. VIDEO y TV Display 16:9 TV Type PAL Wide Screen Format Off Black Level*1 Off • Press RETURN to display the previous menu. • Press SETUP to exit from the setup menu. 1 Press SETUP. 1/1 Closed Caption*1 ➜ The setup menu appears. Off Still Mode Field Component SETUP GENERAL AUDIO 1/2 DVD-Audio mode Move : VIDEO 4 Press Parental Rating Parental Password DISC Auto Power Off Sleep Timer Move : Return Select : Enter 2 Press / repeatedly to select [VIDEO], and then press ENTER. ➜ [VIDEO] menu appears. VIDEO 1/1 TV Display 16:9 TV Type PAL Wide Screen Format Off Black Level*1 Off Closed Caption*1 Off Field Still Mode Interlaced Component RGB Scart Video Out*2 Move : Return Select : Enter *1: [Black Level] and [Closed Caption] are only for U.S.A. and Canada models. *2: [Scart Video Out] is only for U.K., Europe, and Russia models. 16 En Return Select : Enter / to select one of the options below. PAL Select this if the connected TV is a PAL system TV. It will change video signals of NTSC discs and output them in PAL format. Screen Saver HDMI RGB SA-CD mode OSD Language SPEAKER Interlaced Scart Video Out*2 NTSC Select this if the connected TV is an NTSC system TV. It will change video signals of PAL discs and output them in NTSC format. MULTI Select this if the connected TV is compatible with both NTSC and PAL formats (such as a multi-system TV). The output format will be in accordance with the video signals of the disc. Notes • Before changing the current TV Standard setting, ensure that your TV supports the selected TV type system. • If you play an NTSC-formatted disc with the [PAL] setting or a PAL-formatted disc with the [NTSC] setting, the video quality may deteriorate. • When [TV Type] is set to [MULTI], this unit may change the HDMI resolution unwantedly. In this case, try the [NTSC] or [PAL] setting. GETTING STARTED Setting the audio, subtitle and disc menu languages You can select your own preferred language settings. This unit will automatically switch to your preferred language for you whenever you load a disc. If the language selected is not available on the disc, the default language of the disc will be used instead. The OSD (On-Screen Display) language in the system menu will remain once selected. 1 Press SETUP. ➜ The setup menu appears. 2 Press / repeatedly to highlight [DISC], and then press ENTER. ➜ [DISC] menu appears. y DISC • Press RETURN to display the previous menu. • Press SETUP to exit from the setup menu. AUDIO Language 1/1 English Subtitle Language Off DVD Menu Language Setting the OSD (On-Screen Display) language English Angle Mark On PBC Off Time Interval 3 sec 1 Press SETUP. ➜ The setup menu appears. 2 Press / repeatedly to highlight [GENERAL], and then press ENTER. Move : ➜ [GENERAL] menu appears. 1/2 DVD-Audio SA-CD mode SA-CD OSD Language English Parental Rating Level 8 ---- Parental Password On Screen Saver Mode 1 Auto Power Off Off Sleep Timer Move : Return Select : Enter 3 Press GENERAL DVD-Audio mode Return Select : Enter / repeatedly to highlight [AUDIO Language] or [Subtitle Language] or [DVD Menu Language]. 4 Press / to select a language. ■ To select the language not in the list: 1 Select [Others] under [AUDIO Language] or [Subtitle Language] or [DVD Menu Language]. 2 Press ENTER. 3 Use the numeric buttons (0-9) to enter the 4-digit language code (see “LANGUAGE CODE LIST” on page 39). 3 Press / repeatedly to highlight [OSD Language]. 4 Press / 4 Press ENTER. to select a language. 17 En English Step 4: Setting a language preference DISC OPERATION DISC OPERATION 3 Press Notes • Unless otherwise specified, all operations described here are carried out using the supplied remote control. • If the inhibition icon ( or “Prohibit”) appears on the TV screen when you press a button, the function for that button is not available on the current disc or at the current time. • Depending on the DVD or Video CD disc, some operations may operate differently or be restricted. • Do not push on the disc tray or put any objects other than discs on the disc tray. Doing so may cause the disc unit to malfunction. again to close the disc tray. ➜ After recognizing the disc, this unit starts to play back automatically. • If you press PLAY ( 3) when the disc tray is opened, the disc tray closes and playback starts automatically. • Depending on the disc, the disc reading time may exceed 30 seconds due to the complexity of the directory/file configuration. 4 To stop playback, press STOP ( 7). ➜ “RESUME” appears in the front panel display. 5 To resume playback, press PLAY ( 3). Basic operation GROUP ➜ The disc is played back from the last stopping point. y MULTI 2CH PAGE As long as you do not eject a disc, you can resume playback even if you turn off this unit. PROG RANDOM Numeric buttons (0-9) 6 To cancel resume mode, press STOP ( 7) twice. REPEAT Notes A B CLEAR ENTER SETUP SLOW SEARCH STOP STOP ( ) PAUSE ( ) SKIP ( / PAUSE PLAY SLOW/SEARCH ( / ) PLAY ( ) • It may not be possible to play certain MP3/JPEG/DivX® discs due to the configuration and characteristics of the disc or the recording conditions. • When you play a down mix prohibited disc, “NO DOWN MIX” lights in the front panel display. SKIP ) TOP MENU ON SCREEN Pausing playback 1 During playback, press PAUSE ( 8). 1 Press on the front panel to open the disc tray. 2 Place a disc in the disc tray with the printed side up. ➜ Playback is paused and the sound is muted. 2 Press PAUSE ( 8) again to select the next picture frame (frame-by-frame playback). 3 To resume normal playback, press PLAY ( 3). Selecting a track/chapter Press SKIP (l22 / 33l) or use the numeric buttons (0-9) and ENTER to select a track/ chapter number. • • 18 En You can move to the top of the currently playing track/chapter by pressing SKIP (l22 ) once, and move to the previous track/chapter by pressing SKIP (l22 ) twice. During repeat playback of a track/chapter, press SKIP (l22 / 33l) to replay the same track/ chapter. DISC OPERATION MP3, WMA, JPEG, DivX® • For slow search, press PAUSE ( 8) to pause playback before pressing SLOW / SEARCH (22 / 33). 2 While searching, press SLOW / SEARCH (22 / 33) repeatedly to select the desired speed. 3 To resume normal playback, press PLAY ( 3). Notes • For WMA, DTS-CD and JPEG, the search function (backward, forward and slow playback) is not available. • For MP3, slow playback is not available. • For VCD, SVCD and DivX®, the slow backward function is not available. Repeat playback You can repeat single chapter/track, single title/group or entire disc. Also, you can set two points (start and end points) to repeat the specified section. Folder Track 1 Press SLOW / SEARCH (22 / 33). English Searching backward/forward OFF All Chapter: repeats the current chapter Title: repeats the current title Track: repeats the current track Group: repeats the current group Folder: repeats the current folder All*: repeats the entire disc OFF: exits from repeat mode *: This feature may not be available with some discs. Note For VCD and SVCD, repeat playback is not available when the PBC mode is selected. Repeating a section (except DVD-Audio/MP3/WMA/JPEG) 1 During playback, press A-B at the desired starting point. 2 Press A-B again at the desired end point. ➜ The selected section repeats continuously. REPEAT REPEAT A B CLEAR SETUP ENTER 3 To exit from the sequence, press A-B. A-B SLOW SEARCH Random playback (except DVD/SA-CD) Repeating playback Press REPEAT to select the repeat play mode. You can play tracks in random order. ➜ Each time you press the button, the display on the TV screen changes as follows: RANDOM DVD-Video REPEAT PROG RANDOM Title Chapter 1 During playback, press RANDOM. OFF ➜ “RANDOM” appears in the front panel display and all tracks are played in random order. DVD-Audio Group Track 2 To resume normal playback, press RANDOM again. OFF CD, SA-CD, VCD, SVCD All Track OFF 19 En DISC OPERATION Program playback (CD) Note You can customize the playback order for tracks stored in the disc. This unit supports a maximum of 20 programmed tracks. GROUP MULTI 2CH PAGE PROG PROG RANDOM Numeric buttons (0-9) A B CLEAR ENTER SETUP Disc menu operation (DVD/VCD/SVCD) Many DVD, Video CD (version 2.0 only), and SVCD discs include original navigational menus called “DVD menus” and “Video CD playback control menus”. These menus provide a convenient way to operate the disc. REPEAT CLEAR Once you take out the disc from the disc tray or turn off this unit, the stored program play content is cleared. SLOW SEARCH GROUP STOP STOP ( PAUSE MULTI 2CH PAGE PLAY ) PROG Numeric buttons (0-9) SKIP TOP MENU RANDOM REPEAT ON SCREEN A B / CLEAR / / ENTER ENTER ENTER SETUP MENU ENTER SLOW SEARCH RETURN STOP RETURN PLAY PAUSE SKIP 1 Press STOP ( 7) to stop playback if necessary. TOP MENU SKIP ( 2 Press PROG. ➜ The program setup menu appears on the TV screen. 3 Use the numeric buttons (0-9) to enter a track / ) ON SCREEN / / ENTER ENTER MENU / RETURN MENU RETURN number you want to store as a program play. 4 Press to move the cursor to the next field. 5 Repeat step 3-4 until you store all desired tracks. Using the DVD menu 6 Use 1 Press MENU. ■ To clear the selected track number 2 Use / / / to select [Play Program] and then, press ENTER to start program playback. Press CLEAR. 20 En / / / or the numeric buttons (0-9) to select a playback feature or item. 3 Press ENTER to start playback. ■ To clear the list Use / / / then press ENTER. ➜ The DVD menu appears on the TV screen. • Depending on the disc, the DVD menu may appear once you load the disc. to select [Clear All], and ■ To exit from the menu Press MENU. DISC OPERATION Using the OSD menu (DVD/VCD/SVCD/CD) 1 Press MENU to turn on the PBC function. English Using the Video CD playback control (PBC) menu (VCD/SVCD) During playback, press ON SCREEN. ➜ The disc menu appears on the TV screen. • Depending on the disc, the disc menu may appear once you load the disc. ➜ A list of available disc information appears on the TV screen. DVD-Video 2 Use SKIP (l22 / 33l) or the numeric buttons (0-9) to select a playback option. 1 2 DVD VIDEO 3 During playback, press RETURN to return to Title the menu screen. ■ To skip the index menu and play back a disc directly from the beginning Press MENU to turn off the PBC function. Chapter 1/1 Audio 1/1 Subtitle 4 00 : 00 : 10 02 : 15 : 30 1/7 Time Angle 1/1 Bitrate 5 00 : 00 : 10 MPEG 5.1 Ch 1/1 3.072 Mbps 0 y 3 8 9 7 6 DVD-Audio You can also use the setup menu to turn on or off the playback control (PBC) function (see “Selecting the PBC (playback control) function” on page 38). 1 2 DVD AUDIO Group 1 / 1 On-screen display (OSD) menu (DVD/VCD/SVCD/SA-CD) Audio Subtitle The OSD menu shows disc playback information (e.g., the title or chapter number, elapsed playing time or audio/ subtitle language). A number of operations are possible without interrupting disc playback. GROUP MULTI 2CH PAGE 0 Track 1/1 3 4 00 : 00 : 10 02 : 15 : 30 1/8 00 : 00 : 10 MLP 5.1 Ch 1/1 Angle 8 Time 96 k / 24 bit 1/1 7 5 Page 6 1/1 q VCD/SVCD/CD 2 w VCD Track PROG 00 : 00 : 10 1/7 RANDOM Numeric buttons (0-9) Time REPEAT Track Elapsed A B CLEAR ENTER SETUP e SLOW SEARCH STOP PAUSE PLAY SKIP TOP MENU ON SCREEN ON SCREEN / ENTER MENU RETURN / / 1: Current title or group number/Total number of titles or groups 2: Current chapter or track number/Total number of chapters or tracks 3: Elapsed time 4: Time remaining 5: Elapsed time (You can input numbers for time search.) 6: Audio information 7: Current angle number/Total number of available angles 8: Current subtitle number/Total number of available subtitle languages 9: Data transmission speeds 0: Current audio number/Total number of available audio languages q: Current page number/Total number of pages w: Time (You can select a category of time.) e: Category of time being displayed on w 21 En DISC OPERATION ■ To select a title (DVD-Video)/group (DVD-Audio) 1 Press / / / repeatedly to highlight 1, and then enter a title/group number using the numeric buttons (0-9). 2 Press ENTER. 1 Press / / / repeatedly to highlight 2, and then enter a chapter or track number using the numeric buttons (0-9). 2 Press ENTER. ■ To search for a time repeatedly to highlight 5, and then enter hours, minutes and seconds from left to right using the numeric buttons (0-9). / / / 2 Press ENTER. Note When searching for a time, if you enter a time outside the total time for the group/track currently being played back, the inhibition icon ( ) is displayed. ■ To select an angle/subtitle/audio 1 Press repeatedly to highlight 7, 8 or 0, and then enter a audio, subtitle or angle number using the numeric buttons (0-9). / Press / / / repeatedly to highlight w, and then press ENTER to toggle between the category of time. ■ To exit from the OSD menu ■ To select a chapter (DVD-Video)/track (VCD/SVCD/DVD-Audio) 1 Press ■ To select a category of time (VCD/SVCD/CD) / / 2 Press ENTER. Press ON SCREEN. Displaying text information (SA-CD) Some SA-CD discs contain text information (e.g., track name, album name, artist name etc.). If SA-CD text is available on the disc, the track name is automatically displayed on the TV screen once you load the disc. ■ To display the album/artist name During playback, press ON SCREEN. Picture Setting menu (DVD/VCD/SVCD) This unit comes with 10 sets of picture color settings that you can define yourself. Adjusting picture settings 1 Press ON SCREEN twice during playback. ➜ The Picture Setting menu appears on the TV screen. 2 Press / parameter and parameter. to highlight the desired / to adjust the selected Picture Setting Note You cannot change the [Angle]/[Subtitle]/[Audio] setting if the function is not available on the disc you are playing. 01/09 Brightness Move : 0 Adjust : ■ To select a page (DVD-Audio) 1 Press repeatedly to highlight q, and then enter a page number using the numeric buttons (0-9). / 2 Press ENTER. / / 3 Press ON SCREEN to exit from the setup menu. ➜ You can adjust the following parameters. Brightness Set this to adjust the overall brightness of the image. Contrast Set this to adjust the bright areas (white level) in the image. Hue Set this to adjust the hue or phase of the image. 22 En DISC OPERATION Sharpness High Set this to adjust the sharpness of the image for the high frequencies. DNR Set this to reduce video noise. Zooming pictures (DVD-Video/VCD/SVCD/DivX®/ JPEG) You can enlarge the picture on the TV screen and to pan through the enlarged picture. TOP MENU Gamma Set this to adjust the intensity of the picture non-linearly. ON SCREEN / ENTER MENU / / RETURN Chroma level Set this to adjust the density of the color. Chroma delay Set this to adjust the advance delay of the chroma signal for a perfectly clear picture. True Life Set this to adjust the intensity of the picture details. A positive value enables you to reproduce the minute signals of video sources. This function is only available for progressive scan (using the component video jacks) and HDMI output. Availability of picture settings varies according to the connection and settings. SUBTITLE AUDIO ANGLE ZOOM ZOOM 1 During playback, press ZOOM repeatedly to display the picture at different scales (ZOOM 150%, 200%, 300%, or 400%). 2 Press / / / to pan through the enlarged picture. 3 Press ZOOM repeatedly to return to the original HDMI Progressive (Component) Interlaced (Component/ S-video/ CVBS (composite)) Brightness 0 to +6 0 to +6 0 to +6 Contrast –6 to +6 –6 to +6 –6 to +6 Hue –6 to +6 –6 to +6 –6 to +6 (S-video and CVBS only) Sharpness Mid Not available –6 to +6 –6 to +6 Sharpness High Not available –6 to +6 –6 to +6 DNR 0 to +6 0 to +6 0 to +6 Gamma Not available –6 to +6 –6 to +6 Chroma level –6 to +6 –6 to +6 –6 to +6 Chroma Delay Not available –2 to +2 –2 to +2 True Life 0 to +6 0 to +6 Not available size. Viewing angles (DVD-Video) If the disc contains sequences recorded from different camera angles, you can view the picture from a number of different angles. SUBTITLE AUDIO ANGLE ZOOM ANGLE Note Viewing angles available for each disc may vary. Refer to the operating instructions in the DVD menu or on its jacket. Press ANGLE repeatedly to select the desired angle. Note All picture settings are not available for signals output from the AV terminal. 23 En English Sharpness Mid Set this to adjust the sharpness of the image for the intermediate frequencies. DISC OPERATION Audio and Subtitle languages (DVD-Video/VCD) If the disc contains multi-language options, you can select audio/subtitle languages. Note Languages available for each disc may vary. Refer to the operating instructions in the disc menu or on its jacket. y You can set default audio/subtitle languages in the setup menu (see “Setting the audio, subtitle and disc menu languages” on page 17). SUBTITLE AUDIO ANGLE ZOOM DivX® external subtitle files The font sets listed below are available for DivX® external subtitle files. To watch DivX® discs with the desired font set, set the default subtitle language setting in the setup menu to the desired language (see “Setting the audio, subtitle and disc menu languages” on page 17). This unit supports the following languages: Albanian, Breton, Bulgarian, Byelorussian, Catalan, Croatian, Czech, Danish, Dutch, English, Faroese, Finnish, French, German, Hungarian, Icelandic, Irish, Italian, Kurdish (Latin), Macedonian, Greek, Hebrew, Moldavian, Norwegian, Polish, Portuguese, Romanian, Russian, Serbian, Slovak, Slovenian, Spanish, Swedish, Turkish, Ukrainian Notes SUBTITLE AUDIO Selecting an audio language Press AUDIO repeatedly to select an audio language. • Some discs cannot be played depending on disc characteristics or recording conditions. • Some external subtitle files may be displayed incorrectly or not at all. • For external subtitle files, the following filename extensions of subtitle format are supported (note that these files are not shown within the disc navigation menu): .srt, .sub, .ssa, .smi, .ass, .txt, .psb, .sami • The filename of the movie file has to be same as the filename for the external subtitle file. • For a movie file, only one external subtitle file can be loaded. Note For VCD, this function is only available when the [Analog Output] setting is set to [Stereo] (see “Setting the analog output” on page 31). Selecting a subtitle language (DVD-Video) Press SUBTITLE repeatedly to select a subtitle language. Changing pages (DVD-Audio) Many DVD-Audio discs include slide show and page turn capabilities. You can display information pages for photo galleries, artist biographies, lyrics, etc. if the function is available for the disc. Press PAGE (+/–) repeatedly to move to the next/previous page. DIMMER GROUP PAGE (+/ ) 24 En HDMI AUDIO DIRECT STANDBY PAGE MULTI 2CH PROG DISC OPERATION You can select a track in a specific group for DVD-Audio discs and a track/file in a folder for data disc. GROUP Bonus group playback (DVD-Audio) Some DVD-Audio discs contain bonus groups that require a four-digit password to gain access. In this case, refer to the disc jacket and other packaging for information. GROUP MULTI 2CH PAGE MULTI 2CH PAGE GROUP GROUP PROG PROG Numeric buttons (0-9) RANDOM Numeric buttons (0-9) RANDOM REPEAT REPEAT A B A B CLEAR CLEAR ENTER SETUP ENTER SLOW SEARCH STOP PAUSE ENTER SETUP PLAY PAUSE PLAY SKIP TOP MENU ON SCREEN / ENTER ENTER MENU ENTER SLOW SEARCH STOP SKIP TOP MENU English Group/File selection (DVD-Audio/ DivX®/MP3/WMA/Kodak picture CD) ON SCREEN ON SCREEN / ENTER ENTER MENU RETURN RETURN 1 Press GROUP. ➜ A group icon appears on the TV screen. Selecting a group (DVD-Audio) 1 Press GROUP. DVD AUDIO ➜ A group icon appears on the TV screen. Group DVD AUDIO Group Move : Move : 01 / 08 / or the numeric buttons (0-9) to select a group number. 3 Press ENTER. Select : Enter 2 Use / or the numeric buttons (0-9) to select a bonus group number, and then press ENTER. Select : Enter 2 Use 01 / 08 3 Enter a four-digit password using the numeric buttons (0-9), and then press ENTER. 4 Press / to select a track, and then press ENTER. Selecting a file in a folder (DivX®/MP3/WMA/Kodak picture CD) 1 Press / 2 Press / to select a folder, and then press ENTER to open the folder. to select a file, and then press ENTER. ➜ Playback starts from the selected file. • If you use the numeric buttons (0-9) to select a file, playback starts from the selected file automatically. Changing the playback area and layer (SA-CD) There are three types of SA-CD discs: single-layer, duallayer and hybrid. Each type may contain up to two areas of recorded information: a High Quality Stereo area and a High Quality Multi-channel area. You can switch between the SA-CD multi-channel and SA-CD stereo areas. y You can also change the analog output setting using the setup menu (see “Setting the analog output” on page 31). 25 En DISC OPERATION GROUP MULTI 2CH PAGE Media Player MULTI /2CH Time 00 : 00 : 10 PROG ROOT RANDOM SCRNE JPEG REPEAT A B CLEAR ENTER SETUP SLOW SEARCH STOP STOP ( .. 0 JPG A_0510 JPG B_0618 JPG B_0630 JPG C_0731 1 JPG C_0729 5 2 3 4 PLAY PAUSE ) Move : Select : Enter 2 Press / to select a folder, and then press ENTER to open the folder. 1 Press STOP ( 7) to stop playback. 2 Press MULTI / 2CH. • ➜ MULTI indicator lights up when the multi-channel area is selected. To move to the upper folder, select the folder icon with two dots when disc playback is stopped. 3 Press / to select a file, and then press ENTER. Multimedia file playback (MP3/WMA/DivX®/JPEG) ➜ Playback starts from the selected file. • If you use the numeric buttons (0-9) to select a file, playback starts from the selected file automatically. You can play MP3, WMA, DivX® and JPEG files on a personally recorded CD-R/RW disc or commercial CD. Notes Displaying the thumbnail screen (JPEG) • Some files cannot be played correctly depending on disc characteristics or recording conditions. • This unit supports JPEG files of 2848 x 2136 pixels in size. However, some files may not be displayed correctly depending on the aspect ratio of the image. 1 Press MENU during playback. ➜ The thumbnail pictures appear on the TV screen. y You can set the duration for each image of a slide show (see “Setting the duration for a slide show” on page 38). PROG Numeric buttons (0-9) RANDOM REPEAT A B CLEAR SETUP SLOW SEARCH STOP STOP ( 2 Press SKIP (l22 / 33l) to display the other ENTER pictures on the previous/next page. PLAY PAUSE 3 Press ) SKIP TOP MENU SKIP ( / ) 4 Press STOP ( 7) to return to the data disc ON SCREEN / / ENTER ENTER MENU / menu. RETURN MENU 1 Load a disc in the disc tray. ➜ Playback starts automatically. ➜ For MP3 and WMA, the data disc menu appears on the TV screen. ➜ For DivX® and JPEG, press STOP ( 7) during playback to display the data disc menu. 26 En / / / to highlight one of the pictures, and then press ENTER to start playback. Rotating pictures (JPEG) During playback, press / / rotate the picture on the TV screen. / to : rotates the picture counter-clockwise by 90 degrees : rotates the picture clockwise by 90 degrees , : rotates the picture by 180 degrees SETUP MENU English SETUP MENU Menu overview y • The initial setting for each parameter is indicated in bold. • If the settings you have made are inappropriate, you can always reset all options and your personal settings to the initial factory settings. For details, see “Resetting the system” on page 30. Main Menu GENERAL AUDIO SPEAKER Menu item DVD-Audio mode SA-CD mode SA-CD, CD OSD Language English, Deutsch, Français, Español, Italiano, Русский _ _ _ _ (Enter your password) Level 1 to Level 8 Parental Password _ _ _ _ (Enter your password) New Password, Confirm Password Screen Saver On, Off Auto Power Off Mode 1, Mode 2, Off Sleep Timer Off, 30min, 60min, 90min,120min,150min Factory Default _ _ _ _ (Enter your password) Yes, No DivX Registration (DivX registration code is displayed) Enter Analog Output Stereo, Multi-Channel Digital Out All, PCM, Off LPCM Output 48KHz, 96KHz Night Listening Mode On, Off Size Front L/R Large, Small Center, Surround L/R Large, Small, Off Level SA-CD HDMI DISC Setting item/Parameter Parental Rating Distance VIDEO Setting Item/Submenu DVD-Audio, DVD-Video TV Display Subwoofer On, Off Initialize On, Off Unit Feet, Meter Front L/R, Center, Surround L/R 0.3m to 12.0m (1ft to 40ft) Default setting: 3.0m (10ft) Initialize On, Off Front L, Center, Front R, Surround L, Surround R, Subwoofer 0dB to –12dB Test Tone Off, Manual, Auto Initialize On, Off SA-CD Config Config 1, Config 2, Config 3 CUT-OFF Frequency 60, 80, 100, 120 16:9, 4:3 Pan Scan, 4:3 Letter Box TV Type MULTI, NTSC, PAL Wide Screen Format NL Stretch, Pillar Box, Off Black Level (U.S.A. and Canada models only) On, Off Closed Caption (U.S.A. and Canada models only) On, Off Still Mode Frame, Field Component Progressive, Interlaced Scart Video Out (U.K., Europe, and Russia models only) CVBS, RGB HDMI Video 480p/576p, 720p, 1080i, 1080p, Auto DVI Output Range Standard, Enhanced HDMI Audio Auto, PCM, Off AUDIO Language Off ([Subtitle Language] only), English, French, Spanish, Japanese, German, Italian, Russian, Others Subtitle Language DVD Menu Language Angle Mark On, Off PBC On, Off Time Interval 2 sec to 10 sec, Default setting: 3 sec 27 En SETUP MENU 2 Press / to select the desired main menu, and then press ENTER. Setup menu operation Setup is carried out on the TV screen, enabling you to customize this unit to suit your own particular requirements. Follow the procedures below to start the setup menu operations. ➜ Menu items and setting items appear. SPEAKER 1/1 Size Distance Level REPEAT SA-CD A B CLEAR ENTER SETUP SLOW SEARCH SETUP STOP PLAY PAUSE Move : Return Select : Enter SKIP TOP MENU / / / ENTER 3 Press / to highlight the desired menu item. ➜ If the selected menu item has submenus, only a right arrow is displayed on the side of the setting item. In this case, press , and then repeat step 3. ON SCREEN ENTER MENU RETURN RETURN SPEAKER 1/1 SA-CD Config Config 1 CUT-OFF Frequency 100 SUBTITLE AUDIO ANGLE ZOOM y Move : • Press RETURN to display the previous menu. • Press SETUP to exit from the setup menu. • Refer to the following pages for details of the menu that requires a particular operation. 1 Press SETUP. ➜ Main menus and menu items appear on your TV. SETUP GENERAL AUDIO 1/2 Return Select : Enter ➜ If the selected menu item has only setting items, left and right arrows appear on both sides of the setting item. AUDIO 1/1 Analog Output Stereo Digital Out DVD-Audio mode LPCM Output SA-CD mode Night Listening Mode PCM 96KHz Off OSD Language SPEAKER VIDEO Parental Rating Parental Password Screen Saver HDMI DISC Move : 28 En Auto Power Off Move : Sleep Timer Return Select : Enter 4 Press Return Select : Enter / to toggle the setting items or to adjust the parameter. SETUP MENU Notes SETUP GENERAL AUDIO 1/2 DVD-Audio mode SA-CD mode OSD Language SPEAKER VIDEO Parental Rating Setting the OSD language Parental Password Screen Saver HDMI DISC Move : This menu contains various options for the on-screen display (OSD) language. For details, see “Setting the OSD (On-Screen Display) language” on page 17. Auto Power Off Sleep Timer Return Select : Enter Selecting DVD-Audio mode Some DVD-Audio discs contain the DVD-Video content in addition to the DVD-Audio content. You can select DVD-Audio or DVD-Video mode. • Select [DVD-Audio mode] in [GENERAL] menu. DVD-Audio Select this to play back both DVD-Audio and DVD-Video contents. Only the DVD-Audio content may be played back depending on the disc. DVD-Video Select this to play back only the DVD-Video content. Notes • This setting is only available when no disc is loaded in the disc tray. • Selected mode becomes effective after you close the setup menu. y • When a DVD-Audio disc is played back, the DVD AUDIO indicator lights up. • When you select [DVD-Video], the DVD AUDIO indicator goes out. Selecting SA-CD mode Some SA-CD discs contain both SA-CD layer and the standard CD layer. You can select SA-CD or CD mode. • Select [SA-CD mode] in [GENERAL] menu. SA-CD Select this to play back SA-CD layer. CD Select this to play back CD layer. • This setting is only available when no disc is loaded in the disc tray. • Selected mode becomes effective after you close the setup menu. • When you select [CD], this unit does not play back SA-CD discs which do not have CD layer. Restricting playback with parental control Some DVD discs have a parental level assigned to the complete disc or to certain scenes on the disc. This feature lets you set a playback limitation level. The rating levels are from 1 to 8 and are country dependent. You can prohibit playback of certain discs that are not suitable for your children or play certain discs in alternative scenes. 1 Select [Parental Rating] in [GENERAL] menu. 2 Enter your four-digit password using the numeric buttons (0-9). (For details about the password, see “Changing the parental password” below.) ➜ If the password is correct, [Parental Rating] is enabled to select. 3 Press • / to select the rating level. To disable parental controls and have all discs play, select [Level 8]. Notes • VCD, SVCD, CD and SA-CD have no level indication, so the parental control function has no effect with these types of discs. • Some DVD discs are not encoded with a rating though the movie rating may be printed on the disc cover. The rating level feature does not work for such discs. Changing the parental password You can change the password for parental control. Enter your four-digit password when prompted on the screen. The default password is “2580”. 1 Select [Parental Password] in [GENERAL] menu. 29 En English General setup menu SETUP MENU 2 Enter your old four-digit password using the numeric buttons (0-9). • When doing this for the first time, enter “2580”. ➜ If the password is correct, the submenu appears. 3 Enter the new four-digit password using the Resetting the system You can reset all options and your personal settings to the initial factory settings, except [Parental Rating] and [Parental Password]. numeric buttons (0-9). 1 Select [Factory Default] in [GENERAL] menu. ➜ [Confirm Password] is highlighted. 2 Enter your four-digit password using the numeric buttons (0-9). (For details about the password, see “Changing the parental password” on page 29.) 4 Enter the new four-digit password again. ➜ The previous menu screen appears and the new four-digit password is now valid. ➜ The confirmation screen appears. Setting the screen saver GENERAL 2/2 You can turn on or off the screen saver. • DivX Regis Factory Default On Select this to turn on the screen saver when disc playback is stopped for more than 15 minutes. Press [Yes] to confirm Yes Off Select this to disable the screen saver function. Move : Setting the auto power function You can set the auto standby mode. • Mode 2 Select this to set this unit to the standby mode automatically when disc playback is stopped for more than 30 minutes. Off Select this to disable the auto power off function. Setting the sleep timer You can set this unit to the standby mode automatically after a certain elapsed period. • Select [Sleep Timer] in [GENERAL] menu. 30min, 60min, 90min, 120min, 150min Select one to set the sleep timer function. Off Select this to cancel the sleep timer function. 30 En No Return Select : Enter 3 Press / to select [Yes] to reset the system, and then press ENTER. Select [Auto Power Off] in [GENERAL] menu. Mode 1 Select this to set this unit to the standby mode automatically when disc playback is stopped for more than 30 minutes or disc playback is continued for more than six hours without operation. .... Factory Default Select [Screen Saver] in [GENERAL] menu. ➜ All settings are reset to the initial factory settings. Displaying the DivX® VOD registration code Yamaha provides you with the DivX® VOD (Video On Demand) registration code that allows you to rent and purchase videos using the DivX® VOD service. For more information, visit at www.divx.com/vod. 1 Select [DivX Registration] in [GENERAL] menu. 2 Press . ➜ The registration code appears. 3 Press ENTER to return to the previous menu. y To purchase or rent the videos from DivX® VOD service at www.divx.com/vod, use the registration code and download the video onto a CD-R for playback on this unit. Notes • All videos downloaded from DivX® VOD can only be played back on this unit. • The time search function is not available during DivX® movie playback. SETUP MENU Setting the LPCM output Digital Out Set the LPCM output if you have connected this unit to a PCM-compatible receiver via a digital terminal, such as the coaxial or optical terminals. Discs are recorded at a certain sampling rate. The higher the sampling rate, the better the sound quality. LPCM Output • SETUP GENERAL AUDIO SPEAKER 1/1 Analog Output 48KHz Select this to play back discs recorded at the sampling rate of 48 kHz. All 96 kHz PCM data streams (if available) are converted to the sampling rate of 48 kHz. VIDEO HDMI DISC Move : Return Select : Enter Setting the analog output Set the analog output to match the playback capability of this unit. • Select [LPCM Output] in [AUDIO] menu. Night Listening Mode Select [Analog Output] in [AUDIO] menu. Stereo Select this to change channel output to stereo, which only delivers sound from the two front speakers. 96KHz Select this to play back discs recorded at the sampling rate of 96 kHz. If the 96 kHz disc is copy protected, the digital output is automatically converted to a sampling rate of 48 kHz. Setting the night listening mode In this mode, high volume output is softened and low volume output is brought upward to an audible level. It is useful when you watch your favorite action movie without disturbing others at night. Multi-Channel Select this when using a multi-channel audio/(video) receiver with 6 channel inputs. In this mode, this unit performs DTS decoding or Dolby Digital 5.1-channel decoding when applicable. • Setting the digital output Off Select this when you want to enjoy the full dynamic range of surround sound. Set the digital output according to your optional audio component connections. • Select [Digital Out] in [AUDIO] menu. All Select this if you have connected the digital audio output jack to a multi-channel decoder/receiver. Select [Night Listening Mode] in [AUDIO] menu. On Select this to level out the volume. This feature is only available for movies with Dolby Digital mode. Note This mode is only effective for analog output. PCM Select this only if your receiver is not capable of decoding multi-channel audio signals. Off Select this to turn off the digital output. 31 En English Audio setup menu SETUP MENU Initialize You can reset [Size] settings to the initial factory settings. Speaker setup menu 1 Select [Initialize] under [Size] in [SPEAKER] SETUP GENERAL AUDIO 2 Press . Size ➜ The confirmation screen appears. Distance Level SPEAKER menu. 1/1 3 Select [Yes] to reset the setting, and then press SA-CD ENTER. VIDEO ➜ [Size] settings are reset to the initial factory settings. HDMI DISC Move : Return Select : Enter Setting speaker distances You can set the sizes for individual speakers. You can set the distances for individual speakers. Placing all speakers except for the subwoofer at equal distances from the listener is the most ideal way of the speaker positioning in 5.1 channel system. • • Setting speaker sizes Select [Size] in [SPEAKER] menu. Front L/R Set the sizes for front L/R speakers. Large Select this if the connected speakers are large. Small Select this if the connected speakers are small. Center, Surround L/R Set the sizes for center/surround L/R speakers. Large Select this if the connected speakers are large. Small Select this if the connected speakers are small. Off Select this if no center/surround L/R speakers are connected. Subwoofer Select on or off for the subwoofer. On Select this if a subwoofer is connected. Off Select this if no subwoofer is connected. Select [Distance] in [SPEAKER] menu. Unit You can select the display unit of measurement. Feet Select this to input speaker distances in feet. Meter Select this to input speaker distances in meters. Front L/R Set the distance from your listening position to the front speakers. We recommend to place the front left speaker and right speaker at the same distance from the listening position. Center Set the distance from your listening position to the center speaker. Surround L/R Set the distance from your listening position to the surround speakers. We recommend to place the surround left speaker and right speaker at the same distance from the listening position. Control range: 0.3m to 12.0m (1ft to 40ft) Control step: 0.3m (1ft) Notes Notes • These settings are not available for SA-CD discs. See “Setting the SA-CD configuration” on page 33 for the SA-CD setting. • [Center], [Surround L/R] and [Subwoofer] settings are not available when the [Analog Output] setting is set to [Stereo] (see “Setting the analog output” on page 31). • For the [Center] setting, you cannot specify the distance beyond the [Front L/R] setting or below the [Front L/R] setting minus 1.5m (5ft). • For the [Surround L/R] setting, you cannot specify the distance beyond the [Front L/R] setting or below the [Front L/R] setting minus 4.5m (15ft). 32 En SETUP MENU Initialize You can reset [Level] settings to the initial factory settings. 1 Select [Initialize] under [Level] in [SPEAKER] 1 Select [Initialize] under [Distance] in [SPEAKER] menu. menu. 2 Press . 2 Press . ➜ The confirmation screen appears. ➜ The confirmation screen appears. 3 Select [Yes] to reset the setting, and then press 3 Select [Yes] to reset the setting, and then press ENTER. ENTER. ➜ [Level] settings are reset to the initial factory settings. ➜ [Distance] settings are reset to the initial factory settings. Setting the SA-CD configuration Setting speaker levels You can set the volume levels for individual speakers. • Select [Level] in [SPEAKER] menu. Front L, Center, Front R, Surround L, Surround R, Subwoofer Set the volume levels for front L/R speakers, center speaker, surround L/R speakers or subwoofer. Control range: 0dB to –12dB Control step: 1dB Test Tone A test tone can be output to help you judge the volume level of each speaker. 1 Select [Test Tone] under [Level] in [SPEAKER] menu. 2 Press / to select [Off], [Manual] or [Auto]. Off Select this to output no test tone. Manual Select this to output the test tone manually. Auto Select this to output the test tone from each speaker automatically. You can select speaker sizes and on/off statuses for SA-CD discs. You can also select a cut-off (cross-over) frequency for all low-frequency signals. All frequencies below the selected frequency are sent to the subwoofer. • Select [SA-CD] in [SPEAKER] menu. SA-CD Config Select speaker sizes and on/off statuses from the following three settings. Size or on/off Speaker Config 1 Config 2 Config 3 Front L/R Large Small Large Center Large Small Small Surround L/R Large Small Small Subwoofer On On Off CUT-OFF Frequency Select a cut-off (cross-over) frequency for all lowfrequency signals. All frequencies below the selected frequency are sent to the subwoofer. Control range: 60, 80, 100, 120 (Hz) 3 For [Auto], press / to select [Yes] and then press ENTER to output the test tone. For [Manual], press / to select each speaker, and then press ENTER to output the test tone. Notes • The test tone is not output from a center speaker, surround speakers, and a subwoofer when the [Analog Output] setting is set to [Stereo] (see “Setting the analog output” on page 31). • These settings are only effective for analog output. 33 En English Initialize You can reset [Distance] settings to the initial factory settings. SETUP MENU When the aspect ratio of your TV is 4:3: Video setup menu Setting SETUP TV display 1/1 GENERAL 16:9 TV Display Wide Screen Format SPEAKER *2 4:3 Pan Scan TV Type AUDIO VIDEO Playback disc Black Level*1 4:3 Closed Caption*1 Still Mode HDMI DISC Component 16:9 Scart Video Out*2 Move : Return 4:3 Letter Box Select : Enter *1: [Black Level] and [Closed Caption] are only for U.S.A. and Canada models. *2: [Scart Video Out] is only for U.K., Europa, and Russia models. Setting the TV display Set the aspect ratio of this unit to match your TV. The format you select must be available on the disc. • 4:3 *1: The side of the picture may be stretched depending on the TV. In this case, check the screen size and aspect ratio of your TV. *2: If the disc is not assigned to play back with panscan, it is played with letterbox. Setting the TV type Select [TV Display] in [VIDEO] menu. 4:3 Pan Scan Select this if the aspect ratio of your TV is 4:3. In this setting, both sides of the picture to be trimmed or formatted to fit your TV screen. This menu contains the options for selecting the color system that matches your TV. For details, see “Step 3: Setting a TV type” on page 16. 4:3 Letter Box Select this if the aspect ratio of your TV is 4:3. In this setting, a wide picture with black bands on the upper and lower portions of the TV screen are displayed. Selecting the wide screen format 16:9 Select this if you have a widescreen TV. • ■ The relationship between the setting of this unit and the TV display When the aspect ratio of your TV is 16:9 (widescreen): Setting Playback disc 16:9 34 En Select [Wide Screen Format] in [VIDEO] menu. NL Stretch Select this to display of 4:3 image on the 16:9 screen with non-linear stretching. (The center position of the screen is stretched less than the side.) Pillar Box Select this to display 4:3 image on the 16:9 screen without stretching. Even when this unit is playing a disc recorded in the 16:9 squeeze mode, the picture is displayed in the center of the screen. TV display 16:9 4:3 Set the aspect ratio of the projected images on the screen. This function is only available for progressive scan and HDMI output. *1 Off Select this to make no aspect ratio adjustment. SETUP MENU If you set the [TV Type] to [NTSC] (see “Step 3: Setting a TV type” on page 16), set this setting shift to [On] to improve the color contrast during playback. • Select [Black Level] in [VIDEO] menu. On Select this to enhance the black level. Off Select this for the standard black level setting. Notes • This function is only available for CVBS (composite video) and S-video output. • This setting has no effect if the [TV Type] is set to [PAL] or [MULTI] (see “Step 3: Setting a TV type” on page 16). Selecting the closed caption (U.S.A. and Canada models only) Closed captions are data hidden in the video signals of specific discs, and are invisible without the use of a special decoder. The difference between subtitles and captions is that subtitles are intended for hearing persons and captions are for the hearing impaired. Subtitles rarely show all of the audio. For example, captions show sound effects (e.g., “phone ringing” and “footsteps”), while subtitles do not. Before you select this setting, please ensure that the disc contains closed caption information and your TV set also supports this function. • Select [Closed Caption] in [VIDEO] menu. On Select this to enable the closed caption function. Off Select this to disable the closed caption function. Note This function is only available for CVBS (composite video) and S-video output. Setting the still mode You can select the picture quality for pausing or frame-byframe playback. • Select [Still Mode] in [VIDEO] menu. Frame Select this if the picture is unstable when you select [Field]. Field Select this for the standard still mode setting. This setting is suitable for playback of quick motion scenes. Selecting the scan function This function is only available if you have connected this unit to a progressive scan TV through the component video jacks (see “Component video jacks <C>” on page 12). This function is enable you to enjoy accurate color reproduction and high quality images. This unit features DCDi circuit. • Select [Component] in [VIDEO] menu. Progressive Select this to enable the progressive scan function. The confirmation screen appears if you select this. In this case, select [Yes] and then press ENTER. Interlaced Select this to enable the interlaced scan function. y The P.SCAN indicator on the front panel display lights up during progressive playback. Notes on activating progressive scan: • While HDMI video signals are being output, component video is fixed to interlaced video. • In progressive mode, 4:3 aspect images are stretched horizontally on the widescreen TV. Change the aspect ratio settings of your TV if you want to watch the original aspect ratio images without distortion. You can also change the aspect ratio settings in [Wide Screen Format] menu (see “Selecting the wide screen format” on page 34). • Ensure that your TV is equipped with progressive scan. • Connect using a component video cable. 35 En English Selecting the black level (U.S.A. and Canada models only) SETUP MENU HDMI setup menu CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE “STANDARD DEFINITION” OUTPUT. IF THERE ARE QUESTIONS REGARDING OUR VIDEO MONITOR COMPATIBILITY WITH THIS MODEL 525P AND 625P DVD PLAYER, PLEASE CONTACT OUR CUSTOMER SERVICE CENTER. SETUP GENERAL AUDIO Select this setting to toggle the video signal output from the AV terminal between CVBS (composite video) and RGB. • Select [Scart Video Out] in [VIDEO] menu. CVBS Select this to output composite video signals. RGB Select this to output RGB video signals. Note This unit does not output S-video signal from the AV terminal. HDMI Video DVI Output Range HDMI Audio SPEAKER VIDEO HDMI This unit is compatible with the complete line of Yamaha products, including the projectors DPX-1300, DPX-830 and the plasma monitor PDM-4220. Switching the SCART video out (U.K., Europe, and Russia models only) 1/1 DISC Move : Return Select : Enter Setting the HDMI video You can adjust the resolution depending on the monitor you are using. This function is only available when this unit is connected to an HDMI-compatible component via the HDMI jack. This unit is compatible with the following video formats: 480p/60 Hz, 576p/50 Hz, 720p/50 Hz, 60 Hz, 1080i/50 Hz, 60 Hz, and 1080p/50 Hz, 60 Hz. • Select [HDMI Video] in [HDMI] menu. 480p/576p Select this for 480/576 progressive-scan video. 720p Select this for 720 progressive-scan video. 1080i Select this for 1080 interlaced-scan video. 1080p Select this for 1080 progressive-scan video. Auto Select this to set this unit to the best resolution setting automatically based on your monitor. Notes • When [TV Type] is set to [NTSC] or [PAL], video signals with 480p or 576p are output accordingly. • While HDMI video signals are being output, component video is fixed to interlaced video. • For settings other than [Auto], make sure that the selected resolution is supported by the HDMI-compatible monitor you are using. If the selected resolution is not supported, this setting is automatically switched to the most appropriate resolution, and the newly selected resolution is displayed in the top left corner of the display and in the front panel display temporarily. • When you select [1080p] and use an HDMI cable longer than 5 m (16 ft), the picture quality may decrease. 36 En SETUP MENU y SETUP GENERAL Selecting the DVI output range AUDIO SPEAKER VIDEO Set the HDMI audio output to match the connected component. This function is only available when this unit is connected to an HDMI-compatible component via the HDMI jack. For details about the relationship between the audio format and the setting, see “HDMI audio output” on page 13. • Select [HDMI Audio] in [HDMI] menu. Subtitle Language Angle Mark PBC Time Interval DISC Standard Select this if you cannot see the correct image when you select [Enhanced]. Setting the HDMI audio AUDIO Language HDMI Select [DVI Output Range] in [HDMI] menu. Enhanced Select this if black and white in the image is not distinct. 1/1 DVD Menu Language You can select the DVI output range to match the connected component. This function is only available when this unit is connected to an DVI-D-compatible component via the HDMI jack. • English DISC setup menu • Refer to the manual supplied with your monitor to select the appropriate aspect ratio. • You can also select the HDMI resolution by pressing HDMI on the remote control repeatedly. Move : Return Select : Enter Selecting the default audio/subtitle/ DVD menu language These menus contain various language options for the audio, subtitles and disc menus recorded on the DVD. For details, see “Setting the audio, subtitle and disc menu languages” on page 17. Selecting an angle mark display You can switch an angle mark display on or off when sequences recorded from different camera angles are played back. • Select [Angle Mark] in [DISC] menu. Auto Select this to set this unit to the best setting automatically based on the component you have connected via the HDMI jack. On Select this if you want to display an angle mark. An angle mark is displayed continuously. PCM Select this to output the decoded multi-channel or 2ch linear PCM audio signals via the HDMI jack. Off Select this if you do not want to display an angle mark. An angle mark appears for five seconds, and then disappears. Off Select this to turn off the HDMI audio output. Notes • SA-CD signals cannot be output using HDMI. • When [HDMI Audio] is set to [Auto] or [PCM], digital output signals are muted. 37 En SETUP MENU Selecting the PBC (playback control) function You can set playback control (PBC) to on or off. This function is available only on Video CD 2.0 with the playback control (PBC) feature. • Select [PBC] in [DISC] menu. On Select this to display a disc menu. Off Select this not to display a disc menu. y You can also use the MENU button on the remote control to turn on or off the playback control (PBC) function (see “Using the Video CD playback control (PBC) menu (VCD/SVCD)” on page 21). Setting the duration for a slide show You can set the duration that the slides for JPEG files are displayed. • Select [Time Interval] in [DISC] menu. 2 sec to 10 sec Control step: 1 second Note This setting may not work correctly depending on file sizes. 38 En LANGUAGE CODE LIST English LANGUAGE CODE LIST Abkhazian 1112 Fiji 1620 Lingala 2224 Singhalese 2919 Afar 1111 Finnish 1619 Lithuanian 2230 Slovak 2921 Afrikaans 1116 French 1628 Macedonian 2321 Slovenian 2922 Albanian 2927 Frisian 1635 Malagasy 2317 Somali 2925 Amharic 1123 Galician 1722 Malay 2329 Spanish 1529 Arabic 1128 Georgian 2111 Malayalam 2322 Sundanese 2931 Armenian 1835 German 1415 Maltese 2330 Swahili 2933 Assamese 1129 Greek 1522 Maori 2319 Swedish 2932 Aymara 1135 Greenlandic 2122 Marathi 2328 Tagalog 3022 Azerbaijani 1136 Guarani 1724 Moldavian 2325 Tajik 3017 Bashkir 1211 Gujarati 1731 Mongolian 2324 Tamil 3011 Basque 1531 Hausa 1811 Nauru 2411 Tatar 3030 Bengali; Bangla 1224 Hebrew 1933 Nepali 2415 Telugu 3015 Bhutani 1436 Hindi 1819 Norwegian 2425 Thai 3018 Bihari 1218 Hungarian 1831 Oriya 2528 Tibetan 1225 Breton 1228 Icelandic 1929 Panjabi 2611 Tigrinya 3019 Bulgarian 1217 Indonesian 1924 Pashto, Pushto 2629 Tonga 3025 Burmese 2335 Interlingua 1911 Persian 1611 Turkish 3028 Byelorussian 1215 Irish 1711 Polish 2622 Turkmen 3021 Cambodian 2123 Italian 1930 Portuguese 2630 Twi 3033 Catalan 6765 Japanese 2011 Quechua 2731 Ukrainian 3121 Chinese 3618 Javanese 2033 Raeto-Romance 2823 Urdu 3128 Corsican 1325 Kannada 2124 Romanian 2825 Uzbek 3136 Croatian 1828 Kashmiri 2129 Russian 2831 Vietnamese 3219 Czech 1329 Kazakh 2121 Samoan 2923 Volapük 3225 Danish 1411 Kirghiz 2135 Sanskrit 2911 Welsh 1335 Dutch 2422 Korean 2125 Scots Gaelic 1714 Wolof 3325 English 1524 Kurdish 2131 Serbian 2928 Xhosa 3418 Esperanto 1525 Laothian 2225 Serbo-Croatian 2918 Yiddish 2019 Estonian 1530 Latin 2211 Shona 2924 Yoruba 3525 Faroese 1625 Latvian, Lettish 2232 Sindhi 2914 Zulu 3631 39 En TROUBLESHOOTING TROUBLESHOOTING Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center. Problem No power No picture Completely distorted picture or black/white picture The screen size looks unnatural, or the caption is displayed only partially on the TV monitor or is not displayed at all 40 En Solution See page Connect the AC power cable properly. 14 Press STANDBY/ON on the front panel of this unit to turn on the power. 15 Refer to the manual supplied with your TV for correct Video In channel selection. Change the TV channel until you see the DVD screen. – Turn on your TV. – Make sure that all connections on this unit and on all other components are secure. 10 If [Component] is set to [Progressive], check that you have connected this unit to a progressive scan TV through the component video jacks. Otherwise, follow the steps below to turn off the progressive scan; 1. Press on the front panel to open the disc tray. 2. Press CLEAR on the remote control. 3. Press “2580” using the numeric buttons (0-9) on the remote control. 4. Press AUDIO on the remote control. 35 If [HDMI Video] is set to other than [Auto], check that the resolution is supported by the HDMI-compatible monitor you have connected. Otherwise, follow the steps below to change the setting to [Auto]; 1. Press s twice on the front panel or STOP ( 7) twice on the remote control to stop playback. 2. Press and hold s and p/e on the front panel at the same time for three seconds. 36 If the HDMI indicator flashes orange, check that you have connected this unit to an HDCP-compatible component. 12 Check that the video signal output setting matches the video connection. 36 Check that the disc is compatible with this unit. 3 Check that the TV type of this unit is set to match that of the disc and your TV. If you set the TV type improperly, follow the steps below to restore the TV Type setting to the default setting; 1. Press on the front panel to open the disc tray. 2. Press CLEAR on the remote control. 3. Press “2580” using the numeric buttons (0-9) on the remote control. 4. Press AUDIO on the remote control. 16 Check the video connection. 11 Check that the TV setting of this unit matches the screen aspect ratio of your TV. 34 Change the screen size and the aspect ratio of your TV. – TROUBLESHOOTING No sound or distorted sound No audio at digital output No audio at HDMI output Disc does not play Solution See page Adjust the volume on the TV or the AV receiver. – Check that the speakers are connected properly. – Adjust the volume level in the setup menu. 33 Check the digital connections. 11 If you are playing a DTS source, check that your receiver can decode DTS and [Digital Out] is set to [All]. 31 If you are playing an MPEG-2 source, check that your receiver can decode MPEG-2. Otherwise, make sure that [Digital Out] is set to [PCM]. 31 Check that the audio format of the selected audio option on the disc matches your receiver capabilities. – Make sure that [HDMI Audio] is set to [Auto] or [PCM]. 37 No audio signals via the HDMI jack are output if the DVI-D component is connected to this unit using the HDMI-DVI converter cable. To output audio signals via the HDMI jack, connect an HDMI component to this unit. 12 Check that the disc format is supported. 3, 44 The CD-R/RW, DVD+R/RW and DVD-R/RW must be finalized. – Check that the disc label is facing up. 18 Check that the disc is defective by trying another disc. – If you have recorded a JPEG, MP3 or WMA disc yourself, check that your disc contains at least ten JPEG picture files or five MP3/WMA music tracks. – Check the region code of the DVD disc. 3 Picture freezes momentarily during playback Check the disc for fingerprints/scratches and clean it with a soft cloth wiping from the center to the edge. 4 This unit does not respond to the remote control Aim the remote control directly at the remote control sensor on the front panel. 15 Reduce the distance of the remote control from this unit. 15 Replace the batteries in the remote control. 15 Reinsert the batteries with their polarities (+/– signs) as indicated. 15 Buttons do not work Disconnect the power cable from the AC outlet for a few minutes. Reconnect the power cable and try to operate again as usual. – This unit does not respond to some operating commands during playback Operations may not be permitted by the disc. Refer to the instructions of the disc jacket. – Menu items cannot be selected Depending on the connection status or disc availability, some menu items cannot be selected. – Cannot play back SA-CD disc When [SA-CD mode] is set to [CD], this unit does not play back SA-CD discs which does not have CD layer. 29 No sound during DivX® movies playback The audio code may not be supported by this unit. – 41 En English Problem GLOSSARY GLOSSARY ■ Aspect ratio ■ Dolby Digital Horizontal and vertical ratio of a displayed image. The horizontal vs. vertical ratio of conventional TV is 4:3, and that of wide-screens is 16:9. Digital surround sound system which is developed by Dolby Laboratories provides completely independent multi-channel audio. With 3 front channels (left, center, and right) and 2 surround stereo channels, Dolby Digital provides five full-range audio channels. With an additional channel especially for bass effects (called LFE, or low frequency effect), the system has a total of 5.1-channels (LFE is counted as 0.1 channel). By using 2-channel stereo for the surround speakers, more accurate moving sound effects and surround sound environment are possible than with Dolby Surround. ■ Bit Short for binary digit. Represents the smallest unit of information manipulated on a computer. In audio systems, the bit size determines resolution to digitize analog signals. The larger the bit size, the larger the dynamic range (the ratio of maximum and minimum frequency level) and the finer the sounds. Generally, an audio CD is 16 bit and DVD audio is 24 bit. ■ Bit rate The amount of data used to hold a given length of music; measured in kilobits per second, or kbps. Also, the speed at which you record. Generally, the higher the bit rate, or recording speed, the better the sound quality. However, higher bit rates use more space on a disc. ■ Component video jacks Jacks for inputting or outputting a component video signal.Component video signal consists of three lines, the luminance signal (Y) and two color difference signals (PB/ CB, PR/CR), which enable to provide high-quality video. ■ DivX® DivX® is a popular media technology created by DivX, inc. DivX® media files contain highly compressed video with high visual quality that maintains a relatively small file size. DivX® files can also include advanced media features like menus, subtitles, and alternate audio tracks. Many DivX® media files are available for download online, and you can create your own using your personal content and easy-to-use tools from DivX.com. 42 En ■ DTS Digital surround sound system developed by DTS, Inc., which provides 5.1 channel audio (max). With an abundance of audio data, it is able to provide authenticsounding effects. ■ DVD-Audio It has developed for the sole purpose of creating high quality pure sound with Linear PCM and Packed PCM (lossless coding) in up to six audio-channels. Sampling frequencies of 192 kHz/24 bits are supported. ■ HDMI HDMI (High-Definition Multimedia Interface) is the first industry-supported, uncompressed, all-digital A/V (audio/ video) interface. Providing an interface between any A/V source (such as a set-top box or A/V receiver) and an audio/video monitor (such as a digital television – DTV), HDMI supports standard, enhanced or high-definition video as well as multi-channel digital audio using a single cable. HDMI transmits all ATSC (Advanced Television Systems Committee) HDTV standards and supports 8-channel digital audio, with bandwidth to spare to accommodate future enhancements and requirements. GLOSSARY ■ Region code The most common type of scanning used in televisions. It divides a screen into even and odd numbered fields for scanning, and then builds an image by combining them into one image (frame). Many DVD discs include a region code so that the copyright owner can control DVD software distribution only to regions where they are ready to distribute. There are six regions codes, which restrict a DVD player to playing a DVD disc with the same region code. ■ JPEG (Joint Photographic Expert Group) A standardized image compression system proposed by the Joint Photographic Expert Group. It can reduce image data sizes to 1 to 10% of their original sizes, and works on digital photographs effectively. ■ S-video jack A jack for inputting or outputting an S-video signal. S-video signal consists of two lines, the luminance signal (Y) and color signal (C), which enable to provide highquality video during playback or recording. ■ MP3 (MPEG Audio Layer-3) An audio file compression technology. It can reduce audio data sizes to about 10% of their original sizes while maintaining CD-level audio quality. ■ MPEG (Moving Pictures Experts Group) International standard for digital video and audio compression generated by ISO (International Organization for Standardization) and IEC (International Electrotechnical Commission). Includes MPEG-1, MPEG-2, and MPEG-3. MPEG-1 offers VHS level video quality and is often used on video CDs. MPEG-2 offers S-VHS level video quality and is often used on DVDs. ■ Super Audio CD Audio format based upon the current CD standards but includes a greater amount of information that provides higher quality sound. There are three types of discs: single layer, dual layer and hybrid discs. The hybrid disc can be played on existing CD players as well as Super Audio CD players since it contains both standard audio CD and Super Audio CD information. Super Audio CD Disc Hybrid layer disc Dual layer disc Single layer disc HD layer HD layer ■ Parental control Limits Disc play according to the age of the users or the limitation level in each country. The limitation varies from disc to disc; when it is activated, playback will be prohibited if the software’s level is higher than the user-set level. CD layer HD layer Hybrid Super Audio CD Disc 1 CD layer that plays on any CD player High Density layer containing: ■ Playback control (PBC) An on-screen menu recorded on a Video CD or SVCD that enables interactive playback and searching. 2 - High Quality DSD Stereo 3 - High Quality DSD Multi- channel ■ Progressive Scan A method of displaying all scanning lines in a frame at once, reducing flicker noticeable on a larger screen and creating a sharp and smooth image. 43 En English ■ Interlace SPECIFICATIONS SPECIFICATIONS PLAYBACK SYSTEM TV STANDARD • • • • • • • • • • Number of lines........................................PAL: 625, NTSC: 525 • Vertical frequency............................ PAL: 50 Hz, NTSC: 60 Hz • Playback..........................................Multistandard (PAL/NTSC) DVD-Video DVD-Audio DVD-R, DVD-RW DVD+R, DVD+RW, DVD+R DL Video CD, SVCD SA-CD multi-channel and SA-CD stereo CD PICTURE CD CD-R, CD-RW VIDEO PERFORMANCE • Video (CVBS) output ................................... 1 Vpp into 75 ohm • S-video output.......................................... Y: 1 Vpp into 75 ohm C: 0.3 Vpp into 75 ohm • Component video output.......................... Y: 1 Vpp into 75 ohm PB/CB, PR/CR: 0.7 Vpp into 75 ohm • RGB (SCART) output (U.K., Europe, and Russia models only) .................................................................... 0.7 Vpp into 75 ohm • Black level shift (U.S.A. models only) ....................................................... On/Off AUDIO FORMAT • Digital Dolby Digital / DTS / MPEG....................Compressed Digital PCM ........................ 16, 20, 24 bits / fs 44.1, 48, 88.2, 96 kHz MP3 (ISO 9660) .................. 32–320 kbps / fs 16, 22.05, 24, 32, 44.1, 48 kHz WMA ............................................ 64–320 kbps, mono, stereo • Full decoding of Dolby Digital and DTS multi-channel sound • Analog stereo sound • Dolby surround compatible downmix from Dolby Digital multichannel sound AUDIO PERFORMANCE • • • • DA Converter......................................................24 bit, 192 kHz Signal-Noise (1 kHz) .......................................................115 dB Dynamic range (1 kHz)....................................................105 dB DVD......................................................fs 96 kHz, 2 Hz–44 kHz fs 48 kHz, 2 Hz–22 kHz • SVCD....................................................fs 48 kHz, 2 Hz–22 kHz fs 44.1 kHz, 2 Hz–20 kHz • CD/VCD ............................................fs 44.1 kHz, 2 Hz–20 kHz • Distortion and Noise (1 kHz).......................................... 0.002% CONNECTIONS • Video output.................................................... 1 (Cinch: yellow) • S-video output............................................ 1 (Mini DIN, 4 pins) • Component video output Y output.......................................................... 1 (Cinch: green) PB/CB output .................................................... 1 (Cinch: blue) PR/CR output ...................................................... 1 (Cinch: red) • SCART (U.K., Europe, and Russia models only) ........................................................................ 1 (Euroconnector) • Digital output Coaxial ......................................................... 1 (Cinch: orange) Optical..................................1 (IEC 60958 for CDDA/LPCM, IEC 61937 for MPEG 1/2, Dolby Digital, DTS) HDMI ......................................................................1 (Type A) • 2 channel analog output (L+R) ............ 1 pair (Cinch: white/red) • 6 channel analog output Audio Front L/R................................ 1 pair (Cinch: white/red) Audio Surround L/R.......................... 1 pair (Cinch: white/red) Audio Center ...................................................1 (Cinch: black) Audio Subwoofer ............................................1 (Cinch: black) CABINET • Dimensions (W x D x H) .......................... 435 x 284.5 x 87 mm (17–1/8 x 11–3/16 x 3–7/16 inch) • Weight............................................ Approx. 3.3 kg (7 lbs. 4 oz.) POWER SUPPLY • Power inlet U.S.A. and Canada models .......................... AC 120 V, 60 Hz U.K. and Europe models .............................. AC 230 V, 50 Hz Korea and Taiwan models............... AC 100–240 V, 50/60 Hz Asia model ...................................... AC 100–240 V, 50/60 Hz Russia model ................................................ AC 230 V, 50 Hz • Power consumption...............................................Approx. 21 W • Power consumption (standby)............................. less than 0.5 W LASER Type Wave length Output Power Beam divergence Semiconductor laser GaAlAs 650 nm (DVD) 790 nm (VCD/CD) 1.45 mW (DVD) 1.13 mW (VCD/CD) 60 degrees Specifications are subject to change without prior notice. 44 En Limited Guarantee for European Economic Area (EEA) and Switzerland The product is guaranteed to be free from defects in workmanship or materials for a period of two years from the date of the original purchase. Yamaha undertakes, subject to the conditions listed below, to have the faulty product or any part(s) repaired, or replaced at Yamaha’s discretion, without any charge for parts or labour. Yamaha reserves the right to replace a product with that of a similar kind and/or value and condition, where a model has been discontinued or is considered uneconomic to repair. Conditions 1. The original invoice or sales receipt (showing date of purchase, product code and dealer’s name) MUST accompany the defective product, along with a statement detailing the fault. In the absence of this clear proof of purchase, Yamaha reserves the right to refuse to provide free of charge service and the product may be returned at the customer’s expense. 2. The product MUST have been purchased from an AUTHORISED Yamaha dealer within the European Economic Area (EEA) or Switzerland. 3. The product must not have been the subject of any modifications or alterations, unless authorised in writing by Yamaha. 4. The following are excluded from this guarantee: a. Periodic maintenance and repair or replacement of parts due to normal wear and tear. b. Damage resulting from: (1) Repairs performed by the customer himself or by an unauthorised third party. (2) Inadequate packaging or mishandling, when the product is in transit from the customer. Please note that it is the customer’s responsibility to ensure the product is adequately packaged when returning the product for repair. (3) Misuse, including but not limited to (a) failure to use the product for its normal purpose or in accordance with Yamaha’s instructions on the proper use, maintenance and storage, and (b) installation or use of the product in a manner inconsistent with the technical or safety standards in force in the country where it is used. (4) Accidents, lightning, water, fire, improper ventilation, battery leakage or any cause beyond Yamaha’s control. (5) Defects of the system into which this product is incorporated and/or incompatibility with third party products. (6) Use of a product imported into the EEA and/or Switzerland, not by Yamaha, where that product does not conform to the technical or safety standards of the country of use and/or to the standard specification of a product sold by Yamaha in the EEA and/or Switzerland. (7) Non AV (Audio Visual) related products. (Products subject to “Yamaha AV Guarantee Statement” are defined in our website at http://www.yamaha-hifi.com/ or http://www.yamaha-uk.com/ for U.K. resident.) 5. Where the guarantee differs between the country of purchase and the country of use of the product, the guarantee of the country of use shall apply. 6. Yamaha may not be held responsible for any losses or damages, whether direct, consequential or otherwise, save for the repair or replacement of the product. 7. Please backup any custom settings or data, as Yamaha may not be held responsible for any alteration or loss to such settings or data. 8. This guarantee does not affect the consumer’s statutory rights under applicable national laws in force or the consumer’s rights against the dealer arising from their sales/purchase contract. 45 En English Thank you for having chosen a Yamaha product. In the unlikely event that your Yamaha product needs guarantee service, please contact the dealer from whom it was purchased. If you experience any difficulty, please contact Yamaha representative office in your country. You can find full details on our website (http://www.yamaha-hifi.com/ or http://www.yamaha-uk.com/ for U.K. resident).
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project