Roland GP607 Digital Piano Owner's Manual

Roland GP607 Digital Piano Owner's Manual
Owner’s Manual
Bedienungsanleitung
Mode d’emploi
Manuale dell'utente
Manual del usuario
Manual do proprietário
Gebruikershandleiding
For the U.K.
IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
BLUE:
NEUTRAL
BROWN: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
Under no circumstances must either of the above wires be connected to the earth terminal of a three pin plug.
For the USA
Model Name :
Type of Equipment :
Responsible Party :
Address :
Telephone :
DECLARATION OF CONFORMITY
Compliance Information Statement
GP607
Digital Piano
Roland Corporation U.S.
5100 S. Eastern Avenue Los Angeles, CA 90040-2938
(323) 890-3700
Owner’s Manual
°
Play the Piano
˙ Play various sounds
page 8
This unit contains a wide variety of tones (sounds). You can freely select and perform using these tones.
˙ Play two layered tones (Dual Play)
page 9
You can layer two tones on a single key.
˙ Play different tones with your left and right hands (Split Play)
page 9
You can divide the keyboard into left and right zones, and select a different tone for each zone.
˙ Save your performance settings (Registration)
page 16
You can save tone settings and settings for Dual Play or Split, and recall them easily.
°
Practice Songs
˙ Sound a metronome
page 10
You can sound a metronome.
˙ Practice along with the built-in songs
page 11
This unit contains numerous built-in songs.
For the song titles, refer to “Internal Song List” at the end of this manual.
˙ Recording the Song You’re Practicing
page 12
You can record your own playing.
°
Adjust Your Piano
˙ Adjust the keyboard touch
page 8
You can adjust the touch sensitivity of the keyboard to match your own playing style.
˙ Match the pitch to other instruments
page 20
When playing together with other instruments, you can match the unit’s reference pitch to that of the other
instruments (Master Tuning).
˙ Create your own piano (Piano Designer)
page 15
You can customize the sound to your own taste by adjusting the sonic elements of the grand piano sound.
° Simply opening or closing the lid turns the power on/off
1. When you open the lid, the power turns on
automatically.
page 5
2. Use the [Volume] buttons to adjust the volume.
When you close the lid, the power turns off automatically.
Provision of Bluetooth functionality
Please be aware that depending on the country in which you purchased the unit, Bluetooth functionality might not be included.
If Bluetooth functionality is included
The Bluetooth logo appears
when you turn on the power.
Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (leaflet “USING THE UNIT SAFELY” and Owner’s Manual (p. 28)). After reading, keep the
document(s) including those sections where it will be available for immediate reference.
Copyright © 2016 ROLAND CORPORATION
°
Easy Quick Guide
Selecting a Tone
Selecting and Playing Songs
This unit lets you enjoy performing with a variety of piano tones and
other tones.
1
[Other] button
Explanation
Grand piano tones
Electric piano tones
Organ tones
The tones of string instruments such as
violins, as well as other instruments used in
orchestras.
Selects a variety of sounds such as bass or
accompaniment sounds.
2. Use the [–] [+] buttons to select a tone.
MEMO
For more about the sounds, refer to “Tone List” at the end of this manual.
page 8
Using the Metronome
You can perform while hearing a metronome.
1
2
1. Press the [Metronome] button.
2. Press the [Slow] [Fast] buttons.
The metronome tempo changes.
2
3
1
1. Press the [Song] button.
Select a tone group.
[Strings] button
Selecting a song
2
1. Press one of the tone buttons.
Button
[Piano] button
[E. Piano] button
[Organ] button
You can perform along with a song.
Category
Tempo
Time signature
Measure
Song name
2. Use the [K] [J] buttons to select a category.
Category
Explanation
Songs saved on a USB flash drive
USB Memory
Internal Memory Songs saved in internal memory
Piano songs recommended for listening
Listening
Piano Masterpieces
Songs corresponding to the included
Masterpieces
collection of scores, “Roland Classical
Piano Masterpieces.”
Famous popular songs and classical
compositions
Easy Piano
Songs corresponding to the included
collection of scores, “Let’s Enjoy Piano.”
This unit’s
internal songs Scales in all keys
(major scales, minor scales)
Scales
Songs corresponding to the included
collection of scores, “Let’s Enjoy Piano.”
The Virtuoso Pianist No.1–20
Hanon
Vorschule im Klavierspiel Op.101
Beyer
No.1–106
25 Études faciles et progressives Op.100
Burgmüller
100 Übungsstücke Op.139
Czerny100
3. Use the [–] [+] buttons to select a song.
page 10
MEMO
For details on the internal songs, refer to “Internal Song List” at the end of
this manual.
Playing a song
1
2
1. Press the [s] button.
The song plays.
2. Press the [s] button once again.
The song stops.
Song operations
Return to the beginning of
the song
Play/stop
Rewind
Fast-forward
Play all songs in the
selected category
(All Song Play)
Change the song tempo
Press the [u] button.
Press the [s] button.
Press the [x] button.
Press the [y] button.
Hold down the [Song] button and press the
[s] button.
Press the [Slow] [Fast] buttons.
page 11
2
°
Contents
Easy Quick Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting a Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Metronome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting and Playing Songs. . . . . . . . . . . . . . . . . . . . . . . . . .
2
2
2
2
Main Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
Before You Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Opening/Closing the Top . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turning the Power On/Off (Opening/Closing the Lid). . . .
4
4
5
Panel Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
Connecting Your Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
Operation Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
8
8
8
8
8
8
8
9
9
9
9
9
10
10
10
10
11
11
11
11
Selecting a Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Overall Volume. . . . . . . . . . . . . . . . . . . . . . . . .
Adding Reverberation to the Sound (Ambience). . . . . . . .
Adjusting the Brightness of the Sound (Brilliance). . . . . . .
Making Various Settings (Function Mode). . . . . . . . . . . . . .
Changing the Playing Feel of the Keyboard (Key Touch). .
Transposing the Pitch (Transpose). . . . . . . . . . . . . . . . . . . . .
Dividing the Keyboard for Two People (Twin Piano) . . . . .
Saving Your Performance Settings (Registration). . . . . . . .
Playing Different Tones with the Left and Right Hands. . .
Creating Your Own Piano Tone (Piano Designer). . . . . . . . .
Layering Two Sounds (Dual Play). . . . . . . . . . . . . . . . . . . . . .
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Bluetooth Function. . . . . . . . . . . . . . . . . . . . . . . . .
Selecting an Item/Editing a Value . . . . . . . . . . . . . . . . . . . . .
Sounding the Metronome. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting a Song. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Playing Back or Recording. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disabling the Buttons (Panel Lock) . . . . . . . . . . . . . . . . . . . .
Selecting the Part(s) to Play (Part Mute). . . . . . . . . . . . . . . .
Advanced Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Recording Your Performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SMF Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recording a New Song. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overdubbing a Recorded Song . . . . . . . . . . . . . . . . . . . . . . .
Recording Audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Renaming a Song (Rename Song). . . . . . . . . . . . . . . . . . . . .
Copying a Saved Song (Copy Song) . . . . . . . . . . . . . . . . . . .
Deleting a Saved Song (Delete Song). . . . . . . . . . . . . . . . . .
Personalizing Your Piano Sound (Piano Designer). . . . . . . . . . . . .
Saving Your Performance Settings (Registration) . . . . . . . . . . . . .
Recalling a Registration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Saving Current Settings into a Registration. . . . . . . . . . . . .
Saving a Registration Set (Registration Export). . . . . . . . . .
Loading a Saved Registration Set (Registration Import) . .
Loading/Saving Piano Setups. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Saving Piano Settings (Piano Setup Export). . . . . . . . . . . . .
Loading Piano Settings (Piano Setup Import). . . . . . . . . . .
12
12
12
12
13
13
14
14
15
16
16
16
17
17
18
18
18
Convenient Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Initializing the Memory (Format Media). . . . . . . . . . . . . . . .
Restoring the Factory Settings (Factory Reset) . . . . . . . . . .
Various Settings (Function Mode). . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Operations in Function Mode. . . . . . . . . . . . . . . . . . . .
Matching the Pitch with Other Instruments
(Master Tuning). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the Tuning Method (Temperament). . . . . . . . . .
Specifying the Tonic Note (Temperament Key). . . . . . . . . .
Adjusting the Song (SMF) Volume (Song Volume SMF). . .
Adjusting the Song (Audio) Volume
(Song Volume Audio). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Volume of an Audio Playback Device
(Input Volume). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifying the Song (SMF) Playback Mode
(SMF Play Mode). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting the Format for Recording (Recording Mode). . .
Changing How the Pedal Effects Are Applied
(Damper Pedal Part). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing How the Pedals Work (Center Pedal). . . . . . . . . .
Changing the Effect of the Pedal (Left Pedal) . . . . . . . . . . .
Using a Pedal to Switch Registrations (Reg. Pedal Shift) . .
Adjusting the Brightness of the Display
(Display Contrast). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifying a Maximum Volume (Volume Limit) . . . . . . . . .
Preventing Doubled Notes When Connected to a
Sequencer (Local Control). . . . . . . . . . . . . . . . . . . . . . . . . . . .
MIDI Transmit Channel Settings (MIDI Transmit Ch). . . . . .
Changing the Language Displayed in the Screen
(Language) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turning Off the Power When You Close the Lid
(Power Off by the Lid). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Making the Power Automatically Turn off After a Time
(Auto Off ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Saving Settings Automatically (Auto Memory Backup). . .
Using the Bluetooth® Functionality . . . . . . . . . . . . . . . . . . . . . . . . .
Here’s What You Can Do. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using Bluetooth Audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Registering a Mobile Device (Pairing). . . . . . . . . . . . . . . . . .
Connecting an Already-Paired Mobile Device. . . . . . . . . . .
Adjusting the Volume of Bluetooth Audio. . . . . . . . . . . . . .
Using the Pedal to Turn Pages on a Music Score App. . . . .
Connecting an Already-Paired Mobile Device. . . . . . . . . . .
Changing the Operating Keys of the Page Turning
Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the Page-Turn Operation . . . . . . . . . . . . . . . . . . .
Transferring MIDI Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keyboard
Bluetooth
Power Supply
Power
Consumption
Dimensions
Weight
Accessories
Piano Sound: SuperNATURAL Piano Modeling
PHA-50 Keyboard: Wood and Plastic Hybrid Structure, with Escapement and
Ebony/Ivory Feel (88 keys)
Audio: Bluetooth Ver 3.0 (Supports SCMS-T content protection)
MIDI, Turning music sheet: Bluetooth Ver 4.0
AC Adaptor
20
20
20
20
20
20
21
21
21
21
21
21
21
21
22
22
22
22
22
22
23
23
23
23
23
23
24
24
24
24
25
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
USING THE UNIT SAFELY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
IMPORTANT NOTES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Main Specifications
Sound Generator
19
19
19
20
20
Roland GP607: Digital Piano
Option
(sold separately)
Headphones, USB Flash Memory (*1)
*1: Use USB Flash Memory sold by Roland. We cannot guarantee operation if
other products are used.
* This document explains the specifications of the product at the time that the
document was issued. For the latest information, refer to the Roland website.
12 W
Top opened:
1,407 (W) x 949 (D) x 1,521 (H) mm
55-7/16 (W) x 37-3/8 (D) x 59-15/16 (H) inches
Top closed:
1,407 (W) x 949 (D) x 927 (H) mm
55-7/16 (W) x 37-3/8 (D) x 36-1/2 (H) inches
86 kg/189 lbs 10 oz
Owner’s Manual, Leaflet “Stand Assembly”, Leaflet “USING THE UNIT SAFELY”,
Roland Classical Piano Masterpieces, Roland Piano Arrange Collections “Let’s
Enjoy Piano”, AC Adaptor, Power Cord, Headphone Hook
3
°
Before You Play
Opening the top
Opening/Closing the Top
* The top must be opened or closed by an adult.
Raising the music rest
* Raise the music rest before you open the piano top. Close the
piano top before you lower the music rest.
1. Gently raise the music rest.
* When raising the music rest, take care not to pinch your fingers
between the moving part and the body of the unit. In places
where small children are present, make sure that an adult
provides supervision and guidance.
* When opening the top, take care not to pinch your fingers
between the moving part and the body of the unit. In places
where small children are present, make sure that an adult
provides supervision and guidance.
3. Use both hands to firmly grasp the right side of the top
(toward the high notes: position A in the illustration), and
slowly raise it.
2. Fit the latch into one of the slots so that the music rest is at
the desired angle.
A
1.
2.
Using the music holders
You can use the holders to hold pages in place.
When not using the holders, leave them folded down.
Push
* When opening the top, take care not to open it too far. An angle
of about 30 degrees is appropriate. Opening the top significantly
beyond this angle may damage the piano, or cause the top to fall.
Before you open the top, make sure that no one is in the direction
toward which the top opens.
* Do not transport the piano with the top opened. Doing so may
cause the top stick to come out of its socket, allowing the top to
fall.
4. Using one hand to support the top, raise the top stick and
fit it into its socket.
* When raising the top stick, please be careful not to get your
fingers pinched between the movable part and the panel. In
places where small children are present, make sure that an adult
provides supervision and guidance.
5. Move the tip of the top stick to position B of the socket,
locking it into place.
B
NOTE
The top stick must be locked into the socket to prevent the top
from falling.
Do not release the top until the top stick is completely locked.
* To close the top, reverse the procedure by which you opened it.
4
Before You Play
Turning the Power On/Off (Opening/Closing the Lid)
* Once everything is properly connected (p. 7), be sure to follow
the procedure below to turn on their power. If you turn on
equipment in the wrong order, you risk causing malfunction or
equipment failure.
Using the lid to conceal the panel (Classic Position)
You can use the lid to conceal the panel. This allows you to
concentrate on performing without being distracted by the buttons
or the display.
* Before turning the unit on/off, always be sure to turn the volume
down. Even with the volume turned down, you might hear some
sound when switching the unit on/off. However, this is normal
and does not indicate a malfunction.
You can turn the power on/off simply by opening/closing the lid.
Lid
Turning the power on
1. Minimize the volume of the connected devices.
2. Open the lid.
To open the lid, use both hands to lift it lightly, and slide it away from
yourself.
3. Use the [Volume] buttons to adjust the volume.
* This unit is equipped with a protection circuit. A brief interval
(a few seconds) after turning the unit on is required before it will
operate normally.
Turning the power off
1. Close the lid.
To close the lid, pull it gently toward yourself, and lower it softly after
it has been fully extended.
MEMO
55 By pressing the [L] button you can turn the power on/off
while leaving the lid open (p. 6).
55 You can specify that the power not turn off even when you
close the lid (p. 22).
* When opening or closing the lid, take care not to pinch your
fingers between the moving part and the body of the unit. In
places where small children are present, make sure that an adult
provides supervision and guidance.
* If you have any objects (papers, metal objects, etc.) placed on top
of the lid, do not open the lid. Otherwise, such objects may slip
inside the instrument, and then become irrecoverable.
* When turning off the power, do not disconnect the power cord
while the Phones jack “Phones” indicator is lit.
Concerning the Auto Off function
The power to this unit will be turned off automatically after a predetermined
amount of time has passed since it was last used for playing music, or its
buttons or controls were operated (Auto Off function).
If you do not want the power to be turned off automatically, disengage the
Auto Off function (p. 22).
55 Settings that are not saved will be lost when the power is turned off. If you
have any settings that you want to keep, you should save them beforehand.
55 To restore power, turn the power on again.
5
°
Panel Descriptions
[L] Button
The power turns on/off when you open/close
the lid.
If you want to turn the power on/off with the
lid left open, press the [L] button.
To turn the power off, long-press the [L]
button.
* Never disconnect the power cord while the screen
indicates “Don’t disconnect the power.”
Bottom Panel
Connect headphones and USB flash drive.
page 7
Headphone Hook
Front Panel
Whenever you are not using the headphones, you can hang
them on the headphone hook.
This is where you operate the unit.
page 8
* Don’t hang anything other than headphones on this hook, and don’t
apply excessive force to it. Doing so may damage the headphone hook.
Pedal
Damper Pedal
Adjuster
Turn the adjuster to lower it
until the adjuster is in firm
contact with the floor. In
particular, when you’ve placed
the piano on carpet, you must
turn the adjuster until it is
pressing firmly against the floor.
Use this pedal to sustain the sound. While this pedal is held down, notes will be sustained for an extended time even if you
release your fingers from the keyboard.
With the damper pedal on an acoustic piano, when you step on the pedal it will at first offer only a slight amount of
resistance, but as you press down further it will start to feel much heavier. On the unit, this change in the feeling of resistance
is simulated.
On an acoustic piano, when you step on the damper pedal, you’ll first hear the sound of the dampers releasing the strings.
Then, you should also be able to hear the sound of strings adjacent to the ones for the notes actually played resonate
sympathetically, resulting in a rich, resounding tone.
Additionally, when using half-pedaling techniques, the core of the sound disappears rapidly while a rich, spacious resonance
remains, producing a unique form of reverberation. On the unit, the unique, lingering tones produced by the half-pedaling
technique are reproduced in addition to released-string sounds (Damper Noise) and resonating sounds (Damper Resonance).
Sostenuto Pedal
The notes you are pressing when this pedal is depressed will be sustained.
Soft Pedal
This pedal is used to make the sound softer. Playing with the soft pedal depressed produces a sound that is not as strong
as when otherwise played with the equivalent strength. This is the same function as the left pedal of a grand piano. The
softness of the tone can be varied subtly by the depth to which you press the pedal.
* When operating the pedal, take care not to pinch your fingers between the moving part and the body of the unit. Pay special attention to this when using the unit where
children are present.
6
°
Connecting Your Equipment
Input Jack
By connecting an audio player or other audio playback device here,
you can play back the sound of the audio playback device via the unit.
Use the Input Volume (p. 20) to adjust the volume of the device that’s
connected to the Input jack.
USB Memory Port
You can do the following things using a USB flash
drive.
55 WAVE files or MIDI files (SMF) data copied from your
computer can be played back by the unit.
55 You can make audio recordings of your performances on
the unit.
55 The audio recordings of songs that you’ve made can be
played on your computer.
* Carefully insert the USB flash drives all the way in—until it is firmly
in place.
* Never turn off the power or disconnect a USB flash drive or the
power cord while the USB memory access indicator is blinking.
* Use a USB flash drive sold by Roland. We cannot guarantee
operation if any other USB flash drive is used.
Output Jacks
If you connect these jacks to amplified speakers, the sound of the unit
will be heard through them.
* Before turning off the power of the unit, you
must first turn off the power of the devices that
are connected to the Output jacks.
Phones Jacks
Here you can connect stereo headphones.
This unit has two headphone jacks,
two people can also use headphones
simultaneously.
A Headphones 3D Ambience effect will be
applied, producing the sensation that the
sound is emanating from the piano itself
even when using headphones.
* The Headphones 3D Ambience effect applies only to piano sounds;
it does not apply to other sounds.
* You can also turn the Headphones 3D Ambience effect off (p. 8).
* You can use the [Ambience] button to adjust the Headphones 3D
Ambience effect.
USB Computer Port
If you use a commercially available USB
cable to connect the unit’s USB Computer
port to your computer’s USB connector,
you’ll be able to do the following things.
55 SMF data played back by MIDI-compatible
software can be sounded by the unit.
55 MIDI data can be transferred between the unit and your sequencer
software, opening up a wide range of possibilities for music
production and editing.
* To prevent malfunction and equipment failure, always turn down the volume, and turn off all the units before making any connections.
7
°
Basic operations
Operation Guide
Select a setting item
Edit a value
Restore the default value
Use the [K] [J] buttons.
Use the [–] [+] buttons.
Press the [–] [+] buttons
simultaneously.
Selecting a Tone
In addition to piano sounds, the unit lets you enjoy performing with
many other sounds.
These sounds are called “Tones.” The Tones are divided into five groups,
each of which is assigned to a different Tone button.
To select a tone
Press a tone button (e.g., [Piano]) and then use the
[–] [+] buttons.
Tone groups
Button
[Piano] button
[E. Piano] button
Explanation
Grand piano tones
Electric piano tones
Organ tones
* If you’ve selected an organ sound that provides
a rotary effect (*1), such as a Combo Jz. Org or a
Ballad Organ, pressing the [Organ] button will
switch the speed of the rotary effect.
The tones of string instruments such as violins, as
well as other instruments used in orchestras.
Selects a variety of sounds such as bass or
accompaniment sounds.
[Organ] button
Viewing the display
Tone name
[Strings] button
Song
transposition
Time signature
Keyboard transposition
Tempo
Measure
[Other] button
Auditioning the tones (Tone Demo)
1. Hold down the [Key Touch] button and press the [Transpose] button.
2. Select a tone.
MEMO
You can use the [K] [J] buttons to select sounds
of the next category.
*1 Rotary is an effect which simulates the sound of rotating speakers. There is a
choice of two settings: Fast and Slow.
You can hear a tone demo of the first tone in each tone group.
3. To end the tone demo, press the [u] button.
MEMO
For more about the sounds, refer to “Tone List” at the end of this manual.
Adjusting the Overall Volume
You can adjust the speaker volume
when using the internal speakers, or the
headphone volume when headphones are
connected.
Adjusting the volume
0–100
Adding Reverberation to the Sound (Ambience)
Transposing the Pitch (Transpose)
The reverberation that is characteristic of a performance in a concert
hall can be added to the sound.
0–10 (default value: 2)
Adjusting the
reverberation (Ambience)
* If Headphones 3D Ambience is “on,” you can
adjust the depth of the Headphones 3D
Ambience effect.
You can apply a Headphones 3D Ambience effect
that creates the impression that the sound is being
Headphones 3D Ambience heard from the piano itself even when you’re using
headphones.
Off, On (default value: On)
The keyboard or song can be transposed in semitone
steps.
For example if a song is in the key of E major but you want
to play it using the fingering of the C major scale, you
would set the keyboard transpose setting to “4.”
If you play C E G0It will sound E G B
* The reverberation effect is not applied to audio files.
Kbd Transpose
Adjusting the Brightness of the Sound (Brilliance)
You can adjust the brightness of the sound when you play the
keyboard or when you play back a song.
Adjusting the brightness
of the sound
-10–0–10 (default value: 0)
Changing the Playing Feel of the Keyboard (Key Touch)
Making Various Settings (Function Mode)
You can change the playing feel (touch) of the keyboard.
You can make detailed settings for the unit.
1. Simultaneously press the [Ambience] button and [Brilliance]
button.
2. Use the [K] [J] buttons to select the item that you want to set.
3. Use the [–] [+] buttons to edit the setting.
page 20
8
Song Transpose
-6–0–5 (default value: 0)
MEMO
You can also change the keyboard
transpose setting by holding down
the [Transpose] button and pressing
the note that will be the tonic
(root note) of the transposed key.
-12–0–12 (default value: 0)
Fix, 1–100 (default value: 50)
Adjusting the key touch
Hammer Response
* If this is set to “Fix,” each note sounds at the
same volume regardless of how strongly you
play the keyboard.
Adjusts the time from when you play the key until
the piano sound is heard. Higher values produce a
greater delay.
Off, 1–10 (default value: 1)
Operation Guide
Dividing the Keyboard for Two People (Twin Piano)
Creating Your Own Piano Tone (Piano Designer)
You can divide the keyboard into left and right areas so that two
people can play the same range of pitches.
Turning Twin Piano on Turn the [Twin Piano] button on.
Changing the Twin 1. Press a tone button.
Piano tone
2. Use the [–] [+] buttons.
Notes played in the right area are louder in
the right speaker; notes played in the left
area are louder in the left speaker.
Pair
When using headphones, you’ll be able to
Changing the way
hear the other person’s playing.
the sound is heard
Notes played in the right area are heard only
(Mode)
from the right speaker; notes played in the left
area are heard only from the left speaker.
Individual
When using headphones, you won’t be able
to hear the other person’s playing.
Conventional
keyboard
Twin Piano
C1
C2
C3
C3
C4
C5
The damper pedal
for the left area
C4
C6
C5
C3
divide point
C6
C7
C4
C5
You can create your own piano tone by customizing the elements of
the grand piano sound to your taste.
1. Press the [Piano Designer] button.
2. Use the [K] [J] buttons to select the item that
you want to edit.
3. Use the [–] [+] buttons to edit the value.
MEMO
Piano Designer can be used to customize the sound only for [Piano] button
tones.
page 15
C8
C6
The damper pedal
for the right area
Saving Your Performance Settings (Registration)
You can save tone settings and performance settings such as Dual
Play or Split Play, and easily recall them when you wish.
page 16
Playing Different Tones with the Left and Right Hands
(Split Play)
You can play different tones in the areas at the left and right of a
specified key. For example, you can use your left hand to play a bass
tone and use your right hand to play a piano tone.
This feature is called “Split Play,” and the point at which the keyboard
is divided is called the “split point.”
Turning Split on
Changing the right-hand
tone and left-hand tone
Turn the [Split] button on.
1. Use the [K] [J] buttons to select “right-hand tone”
or “left-hand tone.”
2. Press a tone button.
3. Use the [–] [+] buttons.
Changes the split point.
MEMO
You can also specify the split point by holding
down the [Split] button and pressing the key
where you want to split the keyboard.
B1–B6 (default value: F#3)
Changes the volume balance of Split Play.
9:1–9:9–1:9 (default value: 9:9)
Changes the pitch of the left-hand tone in units of
one octave.
-2–0–2 (default value: 0)
Split Point
Balance
Left Shift
You can play two tones simultaneously from a single key. This
function is called “Dual Play.”
Turn the [Dual] button on.
MEMO
You can also use Dual Play by
pressing two tone buttons
simultaneously.
1. Use the [K] [J] buttons to select
“tone 1” or “tone 2.”
2. Press a tone button.
3. Use the [–] [+] buttons.
Adjusts the volume balance
(tone 1: tone 2) for Dual Play.
9:1–9:9–1:9 (default value: 9:4)
Changes the pitch of tone 2 in units of
one octave.
-2–0–2 (default value: 0)
Turning Dual on
Changing tone 1 and
tone 2
Balance
Tone 2 Shift
* Depending on the combination of tones, the effect might not apply to tone 2,
causing the sound to appear differently than usual.
* If you select a sound from the [Piano] button as tone 2, it might sound different
than usual.
Reading the note name (e.g., C4)
F#3
Left-hand tone
Layering Two Sounds (Dual Play)
Right-hand tone
The alphabetical indication for settings such as Split Point shows
the name of the note.
For example, the indication “C4” means “the fourth ‘C’ from the left
edge of the keyboard.”
Split point (Power-up default): F#3
* If you select a sound from the [Piano] button as the left-hand tone, it might
sound different than usual.
C1
C2
C3
C4
C5
C6
C7
C8
9
Operation Guide
Selecting an Item/Editing a Value
Display
This shows information such as the tone name, song name, tempo,
and time signature.
Time signature
Bluetooth
connection
Tempo
Measure
status
Select a setting item
Use the [K] [J] buttons.
Edit a value
Use the [–] [+] buttons.
Change a value
consecutively
Hold down the [–] button or [+] button.
Return to the default value
Hold down the [–] button and [+] button
simultaneously.
Tone name or
song name
Song
transposition
Keyboard
transposition
Sounding the Metronome
Using the Bluetooth Function
Sound from a Bluetooth-equipped audio playback device can be
played through this unit, and use the pedal of this unit to turn pages
of a music score shown on a Bluetooth-equipped display device.
When you turn on the power of this instrument, the Bluetooth
indicator lights.
When pairing is taking place, or when connected or disconnected, the
Bluetooth indicator blinks.
You can sound a metronome while you perform. You can also change
the tempo and time signature of the metronome.
If a song is playing, the metronome sounds at the tempo and time
signature of that song.
Sound the metronome
Change the tempo
page 23
Beat
Down beat
Pattern
Volume
Tone
10
Turn the [Metronome] button on.
Use the [Slow] [Fast] buttons.
10–500
Changes the time signature of the metronome.
MEMO
You can also change the time signature by
holding down the [Metronome] button and
use the [Slow] [Fast] buttons.
2/2, 3/2, 2/4, 3/4, 4/4, 5/4, 6/4, 7/4, 3/8, 6/8, 8/8,
9/8, 12/8 (default value: 4/4)
Sounds a down beat.
Off, On (default value: On)
Changes the pattern of the metronome.
Off, Eighth note, Eighth-note triplet, Shuffle,
Sixteenth note, Quarter-note triplet, Quarter
note, Dotted eighth (default value: Off)
Changes the volume of the metronome.
Off, 1–10 (default value: 5)
Changes the tone of the metronome.
Click, Electronic, Voice (Japanese), Voice (English)
(default value: Click)
Operation Guide
Selecting a Song
Category list
You can select songs in the Song screen.
1. Press the [Song] button to access the Song screen.
Category
USB Memory
Internal Memory
Listening
Category
Masterpieces
Tempo
Time signature
Measure
Song name
Easy Piano
2. Use the [K] [J] buttons to select a category.
3. Use the [–] [+] buttons to select a song.
4. Press the [s] button to play the song.
Scales
MEMO
To select a song from a folder on a USB flash drive, proceed as follows.
Enter the folder
Exit the folder
Use the [–] [+] buttons to select the folder, and press the
[s] (Enter) button.
Use the [–] button to select “(up)” and then press the
[s] (Enter) button.
Playing Back or Recording
Play back the song
at a constant tempo
(Tempo Mute)
Sound a count-in (*1)
MEMO
For details on the internal songs, refer to “Internal Song List” at the end of this
manual.
Disabling the Buttons (Panel Lock)
Here’s how to play back or record a song.
Return to the beginning of
the song
Play/stop
Enter record-ready
condition
Record
Rewind
Fast-forward
Play all songs in the
selected category
(All Song Play)
Change the song tempo
Hanon
Beyer
Burgmüller
Czerny100
Explanation
Songs saved on a USB flash drive
Songs saved in internal memory
Piano songs recommended for listening
Piano Masterpieces
Songs corresponding to the included
collection of scores, “Roland Classical Piano
Masterpieces.”
Famous popular songs and classical
compositions
Songs corresponding to the included
This unit’s
internal songs collection of scores, “Let’s Enjoy Piano.”
Scales in all keys
(major scales, minor scales)
Songs corresponding to the included
collection of scores, “Let’s Enjoy Piano.”
The Virtuoso Pianist No.1–20
Vorschule im Klavierspiel Op.101 No.1–106
25 Études faciles et progressives Op.100
100 Übungsstücke Op.139
Press the [u] button.
By disabling the buttons other than the [L] button and the [Volume]
buttons, you can prevent unintended operation.
Press the [s] button.
Lock the panel
Hold down the [Right] button until the screen
shows the “ ” symbol.
Unlock the panel
Hold down the [Right] button until the “ ”
symbol disappears, or turn off the power.
While stopped, press the [t] button.
In record-ready condition, press the [s] button.
Press the [x] button.
Press the [y] button.
Hold down the [Song] button and press the [s]
button.
Press the [Slow] [Fast] buttons.
Hold down the [s] button and press the [Slow]
button or [Fast] button.
To clear the tempo mute function, hold down the
[s] button once again and press the [Slow]
button or [Fast] button.
Hold down the [Metronome] button and press the
[s] button.
*1 A series of sounds rhythmically played to indicate the tempo before a song
starts is called a “count-in.” If you sound a count-in, it will be easier for you to
synchronize your own performance to the tempo of the playback.
Selecting the Part(s) to Play (Part Mute)
This unit’s songs consist of three parts: accompaniment, left hand,
and right hand.
You can mute a specific part so that it will not sound; only the parts
that you want to hear will play.
Let a part play
Mute a part
Make the button light for parts that you want to
play.
Make the button go dark for parts that you want
to mute.
To make a new recording
1. Select the tone that you want to play.
2. Press the [t] button.
3. Press the [s] (Play/Stop) button to start recording.
4. Press the [s] (Play/Stop) button to stop recording.
To overdub
1. Select the song to be dubbed.
2. Press the [t] button.
3. Press the cursor [J] button.
4. Press the button of the part that you want to record, making it
Accompaniment
part
Left-hand
part
Right-hand
part
* Some songs don’t contain a left-hand part or an accompaniment part. If so,
pressing the corresponding part button does not make it light.
* The Part Mute function is not available when playing an audio file.
blink.
5. Press the [s] (Play/Stop) button to start recording.
6. Press the [s] (Play/Stop) button to stop recording.
Song formats that can be played by the unit
The unit can play back data in the following formats.
page 12
55 SMF formats 0/1
55 Audio files: WAV format, 44.1 kHz, 16-bit linear
11
°
Advanced Operation
˙ Recording Your Performance
It’s easy to record your own performances.
You can play back a recorded performance to check your playing, or
play along with a recorded performance.
Starting your recording and saving it
Type of recording
SMF recording
55 Parts will be separate.
55 You can re-record a specific portion of the song.
55 You can overdub.
1
55 Your performance will be recorded as audio data.
55 The recorded song can be used on your computer.
Audio recording * The acoustic projection effect (*1) is not reproduced for
an audio-recorded song.
* In order to use audio recording, you must connect a USB
flash drive (sold separately) to the USB Memory port.
*1 Acoustic projection is an effect that plays different sounds from each of this
unit’s multiple speakers in order to reproduce the depth and spatial sense
of a piano’s sound. This effect is applied when you play the keyboard, and
when you play back a song that was recorded as SMF.
2
1. Press the [s] button.
After a two-measure count is sounded (the measure number in the
lower right of the display indicates “-2” and then “-1”), recording
starts.
When recording starts, the [t] button and [s] button light.
MEMO
You can also start recording by playing the keyboard. In this case,
a count is not sounded.
2. Press the [s] button.
Recording stops, and your performance is automatically saved.
SMF Recording
MEMO
55 You can change the name of the song (p. 13).
Recording a New Song
55 You can delete the song (p. 14).
* If you want to record with Twin Piano turned on, set SMF Play
Mode (p. 21) to “External.”
Getting ready to record
NOTE
Never turn off the power while “Saving...” is shown in the display.
Listening to the recorded performance
After you record, the newly recorded song is selected.
1. Press the [s] button.
Playback starts from the beginning of your recorded performance.
2
3
4
1. Select the tone that you want to play (p. 8).
2. You can sound the metronome if you like (p. 10).
You can specify the tempo and time signature of the metronome.
MEMO
The metronome’s tempo and time signature settings are stored in
the song, so that the metronome plays correctly even when you
play back the song.
3. Press the [t] button.
The [t] button lights, the [s] button blinks, and the unit enters
record-standby mode.
If you decide to cancel recording, press the [t] button once again.
4. Press the part button of the part that you want to record,
making it blink.
MEMO
For example you can record your performance separately for
each hand by pressing the [Left] button to record your lefthand performance or pressing the [Right] button to record your
right-hand performance. You can also re-record each part after
recording.
* If you don’t select a part at this time, your performance is
recorded to the following buttons.
When playing a single tone [Right] button
Split Play
[Right] button and [Left] button
Twin piano play
Dual Play
[Right] button and [Accomp] button
12
Overdubbing a Recorded Song
You can overdub additional parts onto an SMF recording. For
example, you can separately record the left-hand and right-hand
performances, or record along with an existing song.
* When overdubbing different tones, set the SMF Play Mode (p. 21)
to “External.”
1. Select the song onto which you want to overdub (p. 11).
MEMO
If you want to rerecord only a portion of the song, use the [x]
[y] buttons to move to the measure at which you want to start
recording.
2. Press the [t] button.
The [t] button lights, and the unit enters record-standby mode.
In this case, New Song is selected.
If you decide to cancel recording, press the [t] button once again.
3. Press the cursor [J] button.
The song you selected in step 1 is selected.
MEMO
The song’s tempo and time signature follow the settings of the
song you select.
4. Press the part button of the part that you want to record,
making it blink.
Parts whose button is lit will play back during recording.
5. Start recording as described in “Starting your recording
and saving it” (p. 12).
Advanced Operation
Recording Audio
Here’s how to record your performance on the unit as audio. The
recorded song can be used on your computer.
* The acoustic projection effect (p. 12) is not reproduced for an
audio-recorded song.
Getting ready to record
3
5
3
4
1. Connect your USB flash drive to the USB Memory port
(p. 7).
* Audio data can’t be stored in internal memory.
2. Select the tone that you want to play (p. 8).
3. Hold down the [t] button and press the [+] button to
select “Audio.”
MEMO
Converting an SMF-recorded song to audio
A song recorded as SMF can be re-recorded as audio so that you
can play it back on your computer.
1. Select the song that you want to convert to audio (p. 11).
2. Getting ready for audio recording (“Getting ready to record”
(p. 13)).
1. Connect your USB flash drive.
2. Hold down the [t] button and use the [+] button to select
“Audio.”
3. Press the [t] button.
3. Press the cursor [J] button to select the song of step 1.
4. Press the [s] button to start audio recording (“Starting your
recording and saving it” (p. 13)).
* During recording, any sounds that you produce by playing the keyboard or
that are input to the unit via the USB port, the Input jack, or Bluetooth audio
are included in the audio that is recorded during this conversion. Muted
parts are not recorded.
* Depending on the SMF, it might not be possible to convert it into the
identical audio as when the song was recorded.
Renaming a Song (Rename Song)
Here’s how to rename a previously-saved song.
You can also specify this via the Function mode “Recording Mode”
setting (p. 21).
4. Press the [t] button.
The [t] button lights, the [s] button blinks, and the unit enters
record-standby mode.
If you decide to cancel recording, press the [t] button once again.
1. Press the [Ambience] button and [Brilliance] button
simultaneously.
2. Use the [K] [J] buttons to select “Rename Song,” and then
press the [s] (Enter) button.
The Rename Song screen appears.
NOTE
Never turn off the power or disconnect the USB flash drive during
recording.
5. You can sound the metronome if you like (p. 10).
Starting your recording and saving it
3. Use the [–] [+] buttons to select the media (internal
memory or USB flash drive) that contains the song that you
want to rename.
4. Press the [J] button.
1
2
1. Press the [s] button.
Recording starts.
When recording starts, the [t] button and [s] button light.
2. Press the [s] button.
Recording stops, and your performance is automatically saved.
MEMO
55 You can change the name of the song (p. 13).
5. Use the [–] [+] buttons to select the song that you want to
rename, and then press the [J] button.
6. Rename the song.
[K] [J] buttons
[–] [+] buttons
Select the position at which you want to change
the character.
Change the character.
If you decide to cancel, press the [u] (Exit) button.
7. Press the [s] (Enter) button.
A confirmation message appears.
55 You can delete the song (p. 14).
Listening to the recorded performance
After you record, the newly recorded song is selected.
1. Press the [s] button.
Playback starts from the beginning of your recorded performance.
If you decide to cancel, press the [u] (Exit) button.
8. Use the [J] button to select “Yes,” and then press the [s]
(Enter) button.
The song is renamed.
NOTE
Never turn off the power or disconnect the USB flash drive while
the screen indicates “Executing...”
9. Simultaneously press the [Ambience] button and
[Brilliance] button to exit Function mode.
13
Advanced Operation
Copying a Saved Song (Copy Song)
Songs that have been saved in internal memory can be copied to
USB flash drive. Alternatively, songs stored on a USB flash drive can
be copied to internal memory.
* Audio files cannot be copied.
* If a USB flash drive is not connected, you won’t be able to perform
this operation.
1. Press the [Ambience] button and [Brilliance] button
simultaneously.
2. Use the [K] [J] buttons to select “Copy Song,” and then
press the [s] (Enter) button.
The Copy Song screen appears.
Deleting a Saved Song (Delete Song)
Here’s how to delete a song that you saved on an internal memory or
USB flash drive.
MEMO
If you want to delete all songs that have been saved to internal
memory, initialize the memory.
* If you want to delete a song on the USB flash drive, connect your
USB flash drive to the USB Memory port before you continue.
1. Press the [Ambience] button and [Brilliance] button
simultaneously.
2. Use the [K] [J] buttons to select “Delete Song,” and then
press the [s] (Enter) button.
The Delete Song screen appears.
3. Use the [–] [+] buttons to select the copy-source and copydestination memory locations (internal memory or USB
flash drive).
4. Press the [J] button.
5. Use the [–] [+] buttons to select the song that you want to
copy.
If you decide to cancel, press the [u] (Exit) button.
6. Press the [s] (Enter) button.
The copy is executed.
3. Use the [–] [+] buttons to select the memory location
(internal memory or USB flash drive) that contains the song
you want to delete.
4. Press the [J] button.
5. Use the [–] [+] buttons to select the song that you want to
delete.
6. Press the [s] (Enter) button.
A confirmation message appears.
NOTE
Never turn off the power or disconnect the USB flash drive while
the screen indicates “Executing...”
7. Simultaneously press the [Ambience] button and
[Brilliance] button to exit Function mode.
If you decide to cancel, press the [u] (Exit) button.
7. Use the [J] button to select “Yes,” and then press the [s]
(Enter) button.
The deletion is executed.
NOTE
Never turn off the power or disconnect the USB flash drive while
the screen indicates “Executing...”
8. Simultaneously press the [Ambience] button and
[Brilliance] button to exit Function mode.
14
Advanced Operation
˙ Personalizing Your Piano Sound (Piano Designer)
Parameter
What is Piano Designer?
This unit allows you to personalize
your piano sound by adjusting
various factors that affect the
sound, such as the piano’s strings,
the resonance produced using
the pedals, and the sound of the
hammers striking the strings.
This function is called “Piano
Designer.”
String
Resonance
Hammer Noise
Adjusting the piano
sound to your taste
55 Piano Designer can be used to customize the sound only for
tones of the [Piano] button.
55 Your settings are saved for each tone of the [Piano] button.
4
2
Explanation
Off, 1–10
Full Scale String
Off, 1–10
Res.
MEMO
1
Duplex Scale
Value
3
1. Press the [Piano Designer] button.
The Piano Designer screen appears.
Damper
Resonance
Off, 1–10
Key Off
Resonance
Off, 1–10
Cabinet
Resonance
Off, 1–10
Soundboard
Type
1–5
Damper Noise
Single Note
Tuning
Single Note
Volume
2. Use the [K] [J] buttons to select the item that you want to
edit.
3. Use the [–] [+] buttons to adjust the value.
4. When you’re finished using Piano Designer, press the
[Piano Designer] button or [u] (Exit) button.
A confirmation message appears.
Single Note
Character
Adjusts the sympathetic vibrations of an acoustic piano’s
Duplex Scale.
Higher settings will make the sympathetic vibration
louder.
Adjusts the resonant sound of an acoustic piano (the
sound produced by the strings of previously-pressed
keys vibrating in sympathy with newly played notes, or
the sound of other strings vibrating in sympathy with
the notes you play while pressing the damper pedal).
Higher settings produce louder sympathetic resonance.
Adjusts the overall resonance of the acoustic piano
when its damper pedal is pressed (the sound of
other strings vibrating in sympathy when you press
the damper pedal, and the resonance of the entire
instrument).
Higher settings produce louder sympathetic resonance.
Adjusts sympathetic vibrations such as an acoustic
piano’s key-off sound (the subtle sound that occurs
when you release a note).
Higher settings produce greater tonal change during
the decay.
Adjusts the body resonance of the grand piano itself.
Higher values will produce a larger body resonance.
Selects how the soundboard of the acoustic piano will
resonate.
You can choose from five different types of resonance.
This adjusts the damper noise of the acoustic piano
Off, 1–10 sound (the sound of the damper releasing the strings
when you press the damper pedal).
Specifies a method of tuning (stretch tuning) that is
-50–0–
distinctive to the piano, in which the high register is
+50
tuned slightly sharper and the low register is tuned
slightly flatter.
Adjusts the volume of each key. Higher settings increase
-50–0
the volume.
Adjusts the tonal character of each key. Higher settings
-5–0–+5 produce a harder sound, and lower settings produce a
softer tone.
Here’s how the Piano Designer settings of the selected sound can be
returned to their factory-set state.
1. Press the [s] (Enter) button.
Reset Setting
If you decide to cancel, press the [u] (Exit) button.
2. Use the [J] button to select “Yes,” and then press the
[s] (Enter) button.
The settings return to their factory-set state.
If you decide to cancel, press the [u] (Exit) button.
5. Use the [J] button to select “Yes,” and then press the [s]
(Enter) button.
The Piano Designer settings are saved.
MEMO
If you decide to exit without saving the settings, use the [K]
button to select “No” and then press the [s] (Enter) button.
Piano designer parameter
Parameter
Lid
Key Off Noise
Value
Explanation
0–6
Adjusts the extent to which the lid of the grand piano
is open.
The sound will become more mellow as you close the
lid of the piano in the screen. The sound will become
brighter as you open the lid of the piano in the screen.
Off, 1–10
Hammer Noise -2–0–2
Adjusts the action noise that is heard when you release
a key.
Higher settings produce a louder action noise.
Adjusts the sound produced when the hammer of an
acoustic piano strikes the string.
Higher settings will produce a louder sound of the
hammer striking the string.
88-key settings
(Single Note Tuning, Single Note Volume, Single Note Character)
1. Select an 88-key parameter, and press the [s] (Enter) button.
2. Play the key that you want to edit, and use the [–] [+] buttons to
adjust the settings for that key.
MEMO
You can use the [K] [J] buttons to move to a different 88-key parameter.
3. Press the [u] (Exit) button to return to the previous screen.
What is the duplex scale?
The Duplex Scale is a system of sympathetically vibrating strings sometimes
included in grand pianos.
These sympathetically vibrating strings are not struck directly with hammers,
but sound by vibrating in sympathy with the vibrations of other strings. By
resonating with the overtones, these strings add richness and brilliance to the
sound. These sympathetic strings are added only to the high register above
approximately C4. Since they do not have a damper (a mechanism that stops
them from sounding), they will continue sounding even after you play a note and
then release it to stop the sound of the string that was actually struck.
15
Advanced Operation
˙ Saving Your Performance Settings (Registration)
Tone settings and settings such as Dual Play or Split Play can be
saved and recalled easily.
Such settings are called a “registration.”
You can save a total of 25 registrations, five each in buttons [1]–[5].
These 25 registrations are collectively called a “registration set.”
Recalling a Registration
1. Press the [Registration] button.
2. Press a number button ([1] to [5]) to choose the location
where the desired registration is saved.
3. Press the [–] [+] buttons to select the registration variation.
The settings change accordingly.
You can press the [J] button to edit the selected registration.
MEMO
1-5
1-1
2-5
2-1
3-5
3-1
4-5
4-1
55 You can also use a pedal to recall registrations (p. 21).
5-5
55 If you press the [Registration] button to exit the Registration
screen, you will return to the state prior to recalling the
registration.
5-1
=
25 registrations
Registration set
Saving Current Settings into a Registration
Settings that are saved in a registration
Setting
Ambience
Rotary Speed
Key Touch
Transpose
The selected tone (including Split or Dual tones)
Split on/off
Split point
Left Shift
Dual on/off
Tone 2 Shift
Balance (Split, Dual)
Twin Piano on/off
Twin Piano Mode
Damper Pedal Part
Center Pedal
Left Pedal
MIDI Transmit Ch
Page
p. 8
p. 8
p. 8
p. 8
p. 8
p. 9
p. 9
p. 9
p. 9
p. 9
p. 9
p. 9
p. 9
p. 21
p. 21
p. 21
p. 22
NOTE
When you save a registration into a location, it will overwrite any
registration already stored at that location.
1. While holding down the [Registration] button, press a
button from [1] to [5] to select a registration and then press
the [–] [+] buttons to select a registration variation.
2. Rename the registration.
[K] [J] buttons
[–] [+] buttons
Select the position at which you want to change
the character.
Change the character.
If you decide to cancel, press the [u] (Exit) button.
3. Press the [s] (Enter) button.
The registration is saved.
NOTE
Never turn off the power while the screen indicates “Executing...”
16
Advanced Operation
Saving a Registration Set (Registration Export)
You can save all registrations held in registration memory into a
registration set on a USB flash drive.
1. Connect your USB flash drive to the USB Memory port
(p. 7).
2. Press the [Ambience] button and [Brilliance] button
simultaneously.
3. Use the [K] [J] buttons to select “Registration Export,” and
then press the [s] (Enter) button.
The Registration Export screen appears.
Loading a Saved Registration Set (Registration
Import)
Here’s how a registration set that’s saved on a USB flash drive can be
loaded into the [Registration] button.
NOTE
When you load a registration set, the registrations that were
saved in the [Registration] button are overwritten and lost. If you
don’t want to lose these registrations, save them to a USB flash
drive.
1. Connect your USB flash drive to the USB Memory port
(p. 7).
2. Press the [Ambience] button and [Brilliance] button
simultaneously.
4. Rename the registration set.
[K] [J] buttons
[–] [+] buttons
Select the position at which you want to change
the character.
Change the character.
3. Use the [K] [J] buttons to select “Registration Import,” and
then press the [s] (Enter) button.
The Registration Import screen appears.
If you decide to cancel, press the [u] (Exit) button.
5. Press the [s] (Enter) button.
The settings are saved.
NOTE
Never turn off the power while the screen indicates “Executing...”
6. Simultaneously press the [Ambience] button and
4. Use the [–] [+] buttons to select the registration set that
you want to load.
5. Press the [s] (Enter) button.
A confirmation message appears.
[Brilliance] button to exit Function mode.
If you decide to cancel, press the [u] (Exit) button.
6. Use the [J] button to select “Yes,” and then press the [s]
(Enter) button.
The settings are loaded.
NOTE
Never turn off the power while the screen indicates “Executing...”
7. Simultaneously press the [Ambience] button and
[Brilliance] button to exit Function mode.
17
Advanced Operation
˙ Loading/Saving Piano Setups
This unit lets you load a piano setup that you’ve saved on a USB flash
drive, or save your piano setup to a USB flash drive.
Loading Piano Settings (Piano Setup Import)
1. Connect your USB flash drive to the USB Memory port
MEMO
Only piano setups that were created on the unit can be loaded.
2. Press the [Ambience] button and [Brilliance] button
Settings that are saved as piano settings
Setting
Speaker volume
Headphone volume
Ambience
Headphones 3D Ambience
Brilliance
Key Touch
Hammer Response
Piano Designer settings
Master Tuning
Temperament
Temperament Key
Volume Limit
(p. 7).
simultaneously.
Page
p. 8
p. 8
p. 8
p. 8
p. 8
p. 8
p. 8
p. 15
p. 20
p. 20
p. 20
p. 21
Saving Piano Settings (Piano Setup Export)
3. Use the [K] [J] buttons to select “Piano Setup Import,” and
then press the [s] (Enter) button.
The Piano Setup Import screen appears.
4. Use the [–] [+] buttons to select the piano settings that you
want to load.
5. Press the [s] (Enter) button.
A confirmation message appears.
1. Connect your USB flash drive to the USB Memory port
(p. 7).
2. Press the [Ambience] button and [Brilliance] button
simultaneously.
3. Use the [K] [J] buttons to select “Piano Setup Export,” and
then press the [s] (Enter) button.
The Piano Setup Export screen appears.
If you decide to cancel, press the [u] (Exit) button.
6. Use the [J] button to select “Yes,” and then press the [s]
(Enter) button.
The settings are loaded.
NOTE
Never turn off the power or disconnect the USB flash drive while
the screen indicates “Executing...”
7. Simultaneously press the [Ambience] button and
4. Rename the piano settings.
[K] [J] buttons
[–] [+] buttons
Select the position at which you want to change
the character.
Change the character.
5. Press the [s] (Enter) button.
The settings are saved.
NOTE
Never turn off the power or disconnect the USB flash drive while
the screen indicates “Executing...”
6. Simultaneously press the [Ambience] button and
[Brilliance] button to exit Function mode.
18
[Brilliance] button to exit Function mode.
Advanced Operation
˙ Convenient Functions
Initializing the Memory (Format Media)
Here’s how to erase all of the files that you saved in internal memory
or on a USB flash drive (sold separately).
NOTE
55 When you initialize, all registrations or songs that you saved in
internal memory or on a USB flash drive are lost.
55 If you want settings other than the internal memory settings
to be returned to their factory-set state, execute a Factory
Reset (p. 19).
1. If you want to initialize a USB flash drive, connect the USB
flash drive to the USB Memory port (p. 7).
2. Press the [Ambience] button and [Brilliance] button
simultaneously.
3. Use the [K] [J] buttons to select “Format Media,” and then
press the [s] (Enter) button.
The Format Media screen appears.
If you decide to cancel, press the [u] (Exit) button.
4. Use the [–] [+] buttons to select the media (internal
memory or USB flash drive) that you want to format.
5. Press the [s] (Enter) button.
A confirmation message appears.
Restoring the Factory Settings (Factory Reset)
Here’s how to restore all registrations and internally saved settings to
the factory-set condition. This function is called “Factory Reset.”
NOTE
Factory Reset erases all settings that you have stored, and returns
them to the factory-set condition.
MEMO
Executing this function does not erase the songs in internal
memory or on a USB flash drive (sold separately). If you want to
erase all songs from internal memory or from a USB flash drive,
refer to “Initializing the Memory (Format Media)” (p. 19).
1. Press the [Ambience] button and [Brilliance] button
simultaneously.
2. Use the [K] [J] buttons to select “Factory Reset,” and then
press the [s] (Enter) button.
A confirmation message appears.
If you decide to cancel, press the [u] (Exit) button.
3. Use the [J] button to select “Yes,” and then press the [s]
(Enter) button.
The memory is reset to its factory values.
NOTE
Never turn off the power while the screen indicates “Executing...”
4. Turn the power off, then on again (p. 4).
If you decide to cancel, press the [u] (Exit) button.
6. Use the [J] button to select “Yes,” and then press the [s]
(Enter) button.
The memory is formatted.
NOTE
Never disconnect the USB flash drive or turn off the power while
the screen indicates “Executing...”
7. Simultaneously press the [Ambience] button and
[Brilliance] button to exit Function mode.
Settings that are saved automatically
On the unit, the following settings are saved automatically.
Setting
Speaker volume
Headphone volume
All settings for the Bluetooth function
Power Off by the Lid
Auto Off
Page
p. 8
p. 8
p. 23
p. 22
p. 22
Settings that are saved by Auto Memory Backup
Auto Memory Backup saves the following settings.
Setting
Ambience
Headphones 3D Ambience
Brilliance
Key Touch
Hammer Response
Balance (Split, Dual)
Twin Piano Mode
Metronome (volume, tone, down beat)
Master Tuning
Temperament
Temperament Key
Input Volume
SMF Play Mode
Damper Pedal Part
Reg. Pedal Shift
MIDI Transmit Ch
Display Contrast
Volume Limit
Language
Page
p. 8
p. 8
p. 8
p. 8
p. 8
p. 9
p. 9
p. 10
p. 20
p. 20
p. 20
p. 20
p. 21
p. 21
p. 21
p. 22
p. 21
p. 21
p. 22
19
Advanced Operation
˙ Various Settings (Function Mode)
Basic Operations in Function Mode
1. Simultaneously press the [Ambience] button and [Brilliance] button.
The unit is in Function mode.
2. Use the [K] [J] buttons to select the item that you want to set.
MEMO
Depending on the item that you select, another screen may appear, allowing you to select additional items.
3. Use the [–] [+] buttons to edit the value of the setting.
4. Simultaneously press the [Ambience] button and [Brilliance] button to exit Function mode.
Indication
Value
Explanation
Matching the Pitch with Other Instruments (Master Tuning)
Master Tuning
When playing ensemble with other instruments and in other such instances, you can match the standard pitch to another instrument.
The standard pitch generally refers to the pitch of the note that’s played when you finger the middle A key. For a cleaner ensemble sound while
performing with one or more other instruments, ensure that each instrument’s standard pitch is in tune with that of the other instruments. This
tuning of all the instruments to a standard pitch is called “master tuning.”
415.3 Hz–440.0 Hz–466.2 Hz
Changing the Tuning Method (Temperament)
Temperament
You can play classical styles such as Baroque using historic temperaments (tuning methods).
Most modern songs are composed for and played in equal temperament, the most common tuning in use today. But at one time, there were a wide
variety of other tuning systems in existence.
By playing in the temperament that was in use when a composition was created, you can experience the sonorities of chords originally intended for
that song.
This temperament divides the octave into twelve equal steps. It is the temperament that is most commonly used on today’s
Equal
pianos. Every interval has the same slight amount of dissonance.
In these temperaments, the primary triads are perfectly consonant. It is unsuited to playing melodies and cannot be
Just Major
transposed, but is capable of beautiful sonorities.
Just Minor
The Just tunings differ from major and minor keys.
This tuning, devised by the philosopher Pythagoras, eliminates dissonance in fourths and fifths.
Pythagorean
Although triadic chords are slightly dissonant, this tuning is suitable for songs that have a simple melody.
As in the Just temperaments, the primary triads are consonant in this tuning. Beautiful sonorities are obtained when playing
Kirnberger I
songs that are written in keys appropriate for this tuning.
Kirnberger II
This is a revision of Kirnberger I that reduces the limitations on the usable keys.
This is an improvement of the Meantone and Just tunings that provides a high degree of freedom of modulation.
Kirnberger III
Performances are possible in all keys. Since the resonance differs depending on the key, chords played in this temperament
resonate in diverse ways when compared to equal temperament.
This temperament slightly narrows the fifth relative to Just temperaments. While the Just temperaments contains two
Meantone
types of whole tone (major whole tone and minor whole tone), meantone temperament uses only one type of whole tone
(mean whole tone). Transposition within a limited range of keys is possible.
This temperament consists of eight perfect fifths and four narrowed fifths. Performance in all keys is possible. Since different
Werckmeister
keys produce different sonorities, chords will resonate in diverse ways when compared to equal temperament (Werckmeister
I (III)).
Arabic
This tuning is suitable for the music of Arabia.
Specifying the Tonic Note (Temperament Key)
When playing with tuning other than equal temperament, you need to specify the temperament key for tuning the song to be performed (that is,
Temperament Key
the note that corresponds to C for a major key or to A for a minor key).
If you choose an equal temperament, there’s no need to select a temperament key.
C–B
Refer to “Using Bluetooth Audio” (p. 23).
Bluetooth Audio
Bluetooth Page Turn/MIDI Refer to “Using the Pedal to Turn Pages on a Music Score App” (p. 24).
Refer to “Specifying the Bluetooth ID” (p. 23).
Bluetooth ID
Adjusting the Song (SMF) Volume (Song Volume SMF)
Song Volume SMF
Song Volume Audio
Input Volume
20
Adjusts the volume of the song (SMF).
* If the SMF Play Mode is set to “Internal,” there will be some parts whose volume does not change when you adjust the Song Volume SMF value. If
the SMF Play Mode is set to “External,” the volume of all parts will change.
0 –10
Adjusting the Song (Audio) Volume (Song Volume Audio)
Adjusts the volume of the song (audio).
0–10
Adjusting the Volume of an Audio Playback Device (Input Volume)
You can adjust the volume of an audio playback device that’s connected to the Input jacks.
0–10
Advanced Operation
Indication
Value
Explanation
Specifying the Song (SMF) Playback Mode (SMF Play Mode)
When playing back a song (SMF), select the appropriate setting depending on whether you’re playing an internal song or external data.
MEMO
You can also switch the SMF Play Mode by holding down the [s] button and using the [–] [+] button.
SMF Play Mode
* The acoustic projection effect (p. 12) is not reproduced if the SMF Play Mode is set to “External.” Some of the Piano Designer effects are also not
applied in this case.
Auto Select
Automatically switches the SMF Play Mode to either “Internal” or “External” depending on the song that is being played.
The most suitable tone for the song that’s playing is selected.
Internal
This setting is ideal when playing back an internal song or a song that was recorded on this unit.
The currently selected tone is used when you play back the song.
External
This setting is ideal when playing back external data such as commercially available music data.
Selecting the Format for Recording (Recording Mode)
You can choose whether to record as SMF or as audio.
Recording Mode
MEMO
Rename Song
Copy Song
Delete Song
Piano Setup Export
Piano Setup Import
You can also switch the Recording Mode by holding down the [t] button and using the [–] [+] button.
SMF
SMF parts will be recorded separately. This allows you to re-record just a single part, or to overdub different parts.
Audio
The recording will be made as audio data. The recorded song can be used in your computer.
Refer to “Renaming a Song (Rename Song)” (p. 13).
Refer to “Copying a Saved Song (Copy Song)” (p. 14).
Refer to “Deleting a Saved Song (Delete Song)” (p. 14).
Refer to “Saving Piano Settings (Piano Setup Export)” (p. 18).
Refer to “Loading Piano Settings (Piano Setup Import)” (p. 18).
Damper Pedal Part
When you press the damper pedal during Dual Play or Split Play, the pedal effect is normally applied to both tones, but you can also select the tone
to which the effect is to be applied.
Changing How the Pedal Effects Are Applied (Damper Pedal Part)
Right & Left
Right
Left
All enabled
Applied only to the Tone 1 (in dual mode)/Right-hand Tone (in split mode)
Applied only to the Tone 2 (in dual mode)/Left-hand Tone (in split mode)
Changing How the Pedals Work (Center Pedal)
When you turn on the power, the center pedal functions as the sostenuto pedal (p. 6).
You can change the function of the pedal to a variety of other operations.
Center Pedal
* Pedal function settings take priority in the following order: “Reg. Pedal Shift” 0 “Page Turn (p. 24)” 0 “Center/Left Pedal.”
Sostenuto
Sets function to sostenuto pedal.
Play/Stop
The pedal will have the same function as the [s] button.
Pressing the pedal will layer on Tone 2, used for Dual Play.
Layer
* The Layer function can be applied only when using Dual Play.
Changing the Effect of the Pedal (Left Pedal)
When you turn on the power, the left pedal functions as a soft pedal (p. 6).
You can change this to perform other functions.
Left Pedal
* Pedal function settings take priority in the following order: “Reg. Pedal Shift” 0 “Page Turn (p. 24)” 0 “Center/Left Pedal.”
Soft
The pedal functions as a soft pedal.
Play/Stop
The pedal has the same function as the [s] button.
Pressing the pedal adds tone 2 of the Dual Play function.
Layer
* This is available only when using Dual Play.
Using a Pedal to Switch Registrations (Reg. Pedal Shift)
You can assign a pedal to successively switch registrations Each time you press the pedal, you will switch to the next registration.
Reg. Pedal Shift
Registration Export
Registration Import
Display Contrast
* Pedal function settings take priority in the following order: “Reg. Pedal Shift” 0 “Page Turn (p. 24)” 0 “Center/Left Pedal.”
Off
Pressing the pedal does not change the registration.
The soft pedal can be used only for switching registrations In this case, the function assigned to the soft pedal cannot be
Left Pedal
used.
The sostenuto pedal can be used only for switching registrations In this case, the function assigned to the sostenuto pedal
Center Pedal
cannot be used.
Refer to “Saving a Registration Set (Registration Export)” (p. 17).
Refer to “Loading a Saved Registration Set (Registration Import)” (p. 17).
Adjusting the Brightness of the Display (Display Contrast)
You can adjust the brightness of the unit’s display.
1–10
Specifying a Maximum Volume (Volume Limit)
Volume Limit
You can specify a maximum volume value. This prevents an unnecessarily high volume from sounding even if you inadvertently operate the
[Volume] buttons.
20, 40, 60, 80, 100
21
Advanced Operation
Indication
Value
Explanation
Preventing Doubled Notes When Connected to a Sequencer (Local Control)
Local Control
When you have a MIDI sequencer connected, set this parameter to Local Off.
Since most sequencers have their Thru function turned on, notes you play on the keyboard may be sounded in duplicate, or get dropped. To prevent
this, you can enable the “Local Off” setting so that the keyboard and internal sound generator will be disconnected.
Local Control is off.
Off
The keyboard is disconnected from the internal sound generator. Playing the keyboard will not produce sound.
Local Control is on.
On
The keyboard is connected to the internal sound generator.
MIDI Transmit Channel Settings (MIDI Transmit Ch)
MIDI Transmit Ch
Language
This setting specifies the MIDI channel on which the unit will transmit.
This unit will receive all sixteen channels (1–16).
Off, 1–16
Changing the Language Displayed in the Screen (Language)
You can change the language that is displayed in the screen.
English, Japanese
Turning Off the Power When You Close the Lid (Power Off by the Lid)
Power Off by the Lid
You can choose whether the power turns off when you close the lid.
The power does not turn off when you close the lid.
To turn off the power, press the [L] button.
Ineffective
* If Auto Off is specified, the power automatically turns off when a certain length of time has elapsed after you stop playing
or operating the instrument.
Effective
The power turns off when you close the lid.
Making the Power Automatically Turn off After a Time (Auto Off)
Auto Off
With the factory settings, the unit’s power will automatically be switched off 30 minutes after you stop playing or operating the unit.
If you don’t want the power to turn off automatically, change the “Auto Off” setting to “Off” as follows.
Off, 10, 30, 240 (min)
Saving Settings Automatically (Auto Memory Backup)
Auto Memory Backup
Format Media
Factory Reset
Version
22
You can make settings be saved automatically so that the settings will not change when you turn the power off and on again.
Off
Settings are not saved. When you turn the power off and on again, settings will return to their default values.
Settings are saved automatically.
On
For details on the settings that are saved, refer to “Settings that are saved by Auto Memory Backup” (p. 19).
Refer to “Initializing the Memory (Format Media)” (p. 19).
Refer to “Restoring the Factory Settings (Factory Reset)” (p. 19).
Displays the version of the unit’s system program.
Advanced Operation
˙ Using the Bluetooth® Functionality
Provision of Bluetooth functionality
5. Turn on the Bluetooth function of the mobile device.
Please be aware that depending on the country in which you
purchased the unit, Bluetooth functionality might not be included.
If Bluetooth functionality is included
The Bluetooth logo appears
when you turn on the power.
MEMO
The explanation here uses the iPhone as an example. For details,
refer to the owner’s manual of your mobile device.
Here’s What You Can Do
Bluetooth functionality creates a wireless connection between a
mobile device such as a smartphone or tablet (subsequently referred to
as the “mobile device”) and this unit, allowing you to do the following.
Bluetooth audio
page 23
Music data played back by the mobile device can be heard through
this unit’s speakers.
Page-turning
page 24
A music score display app on the mobile device can be controlled
from this unit.
MIDI data transmission and reception
page 25
MIDI data can be exchanged between this unit and the mobile device.
Using Bluetooth Audio
Registering a Mobile Device (Pairing)
“Pairing” is the procedure
by which the mobile device
Pairing
that you want to use is
registered on this unit (the
two devices recognize each
other).
Make settings so that music
data saved on the mobile device can be played wirelessly via this
unit.
MEMO
55 Once a mobile device has been paired with this unit, there is
no need to perform pairing again. If you want to connect this
unit with a mobile device that has already been paired, refer
to “Connecting an Already-Paired Mobile Device” (p. 23).
55 Pairing is required again if you execute a Factory Reset (p. 19).
55 The following steps are one possible example. For details,
refer to the owner’s manual of your mobile device.
1. Place the mobile device that you want to connect nearby
this unit.
MEMO
If you have more than one unit of this model, power-on only the
unit that you want to pair (power-off the other units).
2. Press the [Ambience] button and [Brilliance] button
simultaneously.
3. Use the [K] [J] buttons to select “Bluetooth Audio,” and
then press the [s] (Enter) button.
The Bluetooth Audio screen appears.
4. Use the [K] [J] buttons to select “Bluetooth Pairing,” and
then press the [s] (Enter) button.
The display indicates “Now pairing...”, and this unit waits for a
response from the mobile device.
6. Tap “GP607 Audio” that is shown in the Bluetooth device
screen of your mobile device.
This unit is paired with the mobile device. When pairing succeeds,
“GP607 Audio” is added to the list of “Paired Devices” on your
mobile device.
MEMO
If the mobile device’s screen asks you to enter a “Pass Key,” enter
“0000” (four zeros).
7. Simultaneously press the [Ambience] button and
[Brilliance] button to exit Function mode.
Specifying the Bluetooth ID
You can specify a number that is added following the device
name of this unit when it is displayed by a Bluetoothconnected application.
If you own multiple units of the same instrument, this is a
convenient way to distinguish them.
1. Press the [Ambience] button and [Brilliance] button
simultaneously.
2. Use the [K] [J] buttons to select “Bluetooth ID,” and
then press the [s] (Enter) button.
3. Use the [–] [+] buttons to edit the value of the setting.
Value
Explanation
0–99
Set to “0”: “GP607 Audio”, “GP607” (default value)
Set to “1”: “GP607 Audio1”, “GP607_1”
Connecting an Already-Paired Mobile Device
1. Turn on the Bluetooth function of the mobile device.
MEMO
55 If you were unable to establish a connection using the
procedure above, tap “GP607 Audio” that is displayed in the
Bluetooth device screen of the mobile device.
55 To disconnect, either turn this unit’s Bluetooth Audio function
“Off” (Function mode0“Bluetooth Audio”0“Bluetooth
Audio” Off ) or turn the mobile device’s Bluetooth function off.
Adjusting the Volume of Bluetooth Audio
Normally you’ll adjust the volume on your mobile device.
If this does not provide the volume adjustment you want, you can
adjust the volume as follows.
1. Proceed with steps 2–3 of “Registering a Mobile Device
(Pairing)” (p. 23).
2. Use the [K] [J] buttons to select “Bluetooth Volume,” and
use the [–] [+] buttons to adjust the volume.
MEMO
If you decide to cancel pairing, press the [u] (Exit) button.
23
Advanced Operation
Using the Pedal to Turn Pages on a Music Score App
Here’s how to use this unit’s pedal to operate (turn pages) a music
score app on your mobile device.
Note when using an already-paired iOS device
iOS
The following operation is required after each time that you
switch the Bluetooth page-turning/MIDI function or execute
a factory reset.
If the keyboard is no longer shown on the mobile device
In some cases, depending on the mobile device app that you’re
using, the keyboard might stop being displayed (i.e., the keyboard
might become unavailable).
If you want the mobile device’s keyboard to be shown while you’re
using the page turning function, hold down this unit’s [Accomp]
button and press the [Left] button.
To hide the mobile device’s keyboard, once again hold down the
[Accomp] button and press the [Left] button.
Connecting an Already-Paired Mobile Device
1. Turn on the Bluetooth function of the mobile device.
This unit will be wirelessly connected to the mobile device.
MEMO
55 If the above steps do not succeed in establishing a
connection, tap the model name (“GP607”) that is shown in
the Bluetooth device screen of the mobile device.
1
Disconnect “GP607.”
2
Turn off.
55 To disconnect, either turn this unit’s Bluetooth Page
Turn function “Off” (Function mode0“Bluetooth Turn/
MIDI”0“Bluetooth Turn&MIDI (*1)” Off ) or turn the mobile
device’s Bluetooth function off.
(*1) Depending on the Function mode “Bluetooth Turn/MIDI” setting, the
screen might indicate “Bluetooth Page Turn” or “Bluetooth MIDI.”
For details, refer to the owner’s manual of your iOS device.
1. Place the mobile device that you want to connect nearby
this unit.
MEMO
If you have more than one unit of this model, power-on only the
unit that you want to pair (power-off the other units).
2. Press the [Ambience] button and [Brilliance] button
simultaneously.
3. Use the [K] [J] buttons to select “Bluetooth Page Turn/
MIDI,” and then press the [s] (Enter) button.
4. Use the [K] [J] buttons to select “Bluetooth Turn/MIDI,”
and use the [–] [+] buttons to select “Page Turn.”
MEMO
By selecting “Page Turn&MIDI” here, you can use the page-turning
function and the MIDI transmit/receive function simultaneously.
For example, this lets you use the pedal to operate the
page-turning function while receiving MIDI to play from this
instrument.
5. Turn on the Bluetooth function of the mobile device.
6. On your mobile device, tap “GP607.”
This unit will be paired with the mobile device. When pairing
succeeds, the model name of this unit (“GP607”) is added to the
“Paired Devices” list of the mobile device.
MEMO
55 If you’re using an iOS device (iPhone or iPad), the screen of
the iOS device indicates “Bluetooth Pairing Request.” Tap the
[Pair] button.
55 If the screen of the mobile device requests you to enter a “Pass
Key,” enter “0000” (four zeros).
7. Simultaneously press the [Ambience] button and
[Brilliance] button to exit Function mode.
Start the music score app on your mobile device; now you can use
the sostenuto pedal to turn to the next page, or the soft pedal to
turn to the previous page.
* Pedal function settings take priority in the following order: “Reg.
Pedal Shift (p. 21)” 0 “Page Turn” 0 “Center/Left Pedal (p. 21).”
24
Changing the Operating Keys of the Page Turning
Function
The key operations for turning pages will differ depending on the
music score display app that you’re using. You can choose which keys
of this unit will operate the page turning function.
1. Proceed with steps 2–3 of “Using the Pedal to Turn Pages
on a Music Score App” (p. 24).
2. Use the [K] [J] buttons to select “Page Turn Assign,” and
use the [–] [+] buttons to select the function.
Setting
Cursor Up/
Down
Explanation
The [.] [/] keys of the keyboard are used by the page
turning app.
The [Page Up] [Page Down] keys of the keyboard are used
Page Up/Down
by the page turning app.
Cursor Left/
The [1] [0] keys of the keyboard are used by the page
Right
turning app.
3. Simultaneously press the [Ambience] button and
[Brilliance] button to exit Function mode.
Changing the Page-Turn Operation
You can select the type of pedal operation that turns pages.
1. Proceed with steps 2–3 of “Using the Pedal to Turn Pages
on a Music Score App” (p. 24).
2. Use the [K] [J] buttons to select “Page Turn Mode” and use
the [–] [+] buttons to select the function.
Value
Once
Twice
Explanation
The page turns when you press the pedal once.
The page turns when you press the pedal twice in quick
succession.
If you press the pedal once, it performs the usual pedal function.
3. Simultaneously press the [Ambience] button and
[Brilliance] button to exit Function mode.
Advanced Operation
Transferring MIDI Data
Here’s how to make settings for transmitting and receiving MIDI data
between this unit and the mobile device.
Note when using an already-paired iOS device
iOS
The following operation is required after each time that you
switch the Bluetooth page-turning/MIDI function or execute
a factory reset.
1
Disconnect “GP607.”
Connection status between this unit and the mobile device
Depending on the functionality of the mobile device that’s
connected, this unit’s display will show the following icons.
Function
Displayed icon
Bluetooth audio function
(AUDIO)
Page turning function
(PAGE)
MIDI data transmit/receive
(MIDI)
Page turning function and MIDI
data transmit/receive
(P+MID)
2
Turn off.
For details, refer to the owner’s manual of your iOS device.
1. Place the mobile device that you want to connect nearby
this unit.
MEMO
If you have more than one unit of this model, power-on only the
unit that you want to pair (power-off the other units).
2. Press the [Ambience] button and [Brilliance] button
simultaneously.
3. Use the [K] [J] buttons to select “Bluetooth Page Turn/
MIDI,” and then press the [s] (Enter) button.
4. Use the [K] [J] buttons to select “Bluetooth Turn/MIDI,”
and use the [+] button to select “MIDI.”
5. Turn on the Bluetooth function of the mobile device.
MEMO
The explanation here uses the iPhone as an example. For details,
refer to the owner’s manual of your mobile device.
6. In the mobile device’s app (e.g., GarageBand), establish a
connection with this unit.
NOTE
Do not tap the “GP607” that is shown in the Bluetooth settings of
the mobile device.
25
°
Troubleshooting
Problem
Even though
you’re using
headphones
and the sound
is muted, a
thumping sound
is heard when
you play the
keyboard
Power turns off
on its own
Power turns on
unexpectedly
Power does not
turn on
Can’t perform
operations
Pedal does
not work, or is
“stuck”
Unable to read
from/write to
USB flash drive
“Buzz” is heard
from external
devices
Items to check
Action
Could you be hearing
the sound of the
hammers inside
the keyboard, or
vibrations in the floor
or walls?
Playing the keyboard causes internal
hammers to operate, and the
vibrations may be transmitted to
the floor or walls. To minimize such
vibrations, you can move the piano
away from the wall, or lay down a
commercially available anti-vibration
mat designed for use with pianos.
Could the auto-off
If you don’t need the power to turn
setting be something off automatically, turn the Auto Off
other than “Off”?
setting “Off.”
This unit powers-on when you open the lid, and powers-off
when you close the lid.
Is the AC adaptor connected correctly?
–
p. 22
p. 5
–
Could Panel Lock be
p. 11
Disengage the Panel Lock setting.
activated?
–
Is the pedal connected correctly?
Could you have
disconnected or
Power-off the unit before you connect
–
connected the pedal
or disconnect the pedal cord.
cord while the power
was on?
p. 21
Could the Damper pedal part be set to “Right” or “Left”?
Could Twin Piano be turned on?
If Twin Piano is on, the right pedal will affect only the rightp. 9
hand keyboard zone and the left pedal will affect only the
left-hand keyboard zone.
Could you have
Return the pedal function (Center
changed the function Pedal, Left Pedal, Reg. Pedal Shift) to
p. 21
of the pedal?
its previous setting.
Are you using
–
(optional) Roland USB Use a USB flash drive sold by Roland.
flash drive?
Are the external
If you connect external devices, be
devices connected
–
sure to connect them to the same AC
to more than one AC
outlet.
power outlet?
The volume
Could the Input Volume be turned down?
level of the unit
connected to
Input jack is too Could the volume of the connected device be turned down?
low
Are your amp, speakers, headphones, etc., connected
correctly?
Is the volume turned down?
Could headphones or an adaptor plug be inserted in the
Phones jacks?
The speakers will not produce sound if headphones or plug
are connected to the Phones jacks.
Has Local Control
No sound
Set Local Control to “On.”
been set to “Off”?
Could Twin Piano mode be set to “Individual”?
If headphones are connected when Twin Piano is On and
the mode is set to Individual, notes played in the left-hand
keyboard zone will not be heard from the headphones
connected to the right Phones jack. Similarly, notes played
in the right-hand keyboard zone will not be heard from the
headphones connected to the left Phones jack.
No sound when
you play back a Could the song volume be set to “0”?
song
Notes don’t sound right
Could you have made Transpose settings?
Pitch of the
Is the Master Tune setting appropriate?
keyboard or
Is the setting for the Temperament correct?
song is incorrect
Is the Single Note Tuning setting appropriate?
Could you be holding down the damper pedal and sounding
Notes are
a large number of notes?
interrupted
Could you be using Dual Play or playing along with a song?
Is the unit in Dual
Press the [Dual] button to turn off
Play?
Dual Play.
Sounds are
heard twice
If you don’t want the other sound
Could the unit be
(doubled) when
module to produce sound, turn your
connected to an
the keyboard is
DAW’s soft thru function “off.”
external sequencer?
played
If Local Control is turned “On,” set
Local Control to “Off.”
Effect does not For some combinations of tones, the effect does not apply to
apply
Dual Play tone 2 or to the left-hand tone of Split Play.
26
Page
p. 20
–
p. 7
p. 8
–
p. 22
p. 9
p. 20
p. 8
p. 20
p. 20
p. 15
–
p. 9
–
p. 22
–
Page
Items to check
Action
Even if the Ambience effect is off, the acoustic piano’s own
resonance remains.
p. 15
You can reduce this reverberation by adjusting the Cabinet
Resonance.
This simulates the characteristics of an acoustic piano, and is
not a malfunction.
–
The sound will change where there is a change in the number
of strings per key or a transition from wound strings to
unwound strings.
If you don’t hear it through headphones: It may be that
the unit has malfunctioned. Please contact your dealer or a
Roland customer service center.
If you also hear it through headphones: To decrease the
High-pitched
–
ringing is heard metallic ringing, adjust the following settings.
55 Duplex Scale (p. 15)
55 Full Scale String Res. (p. 15)
55 Ambience (p. 8)
Could the volume be
p. 8
Lower the volume.
set to maximum?
If you also hear it through headphones: It may be that the
unit has malfunctioned. Please contact your dealer or a
Roland customer service center.
If you don’t hear it through headphones: Objects near the
Low notes
sound wrong, or unit are resonating because of the high volume of sound
coming from the speakers. You can take the following
are buzzy
–
measures to minimize resonances.
Problem
Reverberation
remains even if
you defeat the
Ambience effect
The sound
of the higher
notes suddenly
changes from a
certain key
55 Locate the speakers 10–15 cm (4–6 inch) away from walls
or other surfaces.
55 Keep the volume down.
55 Move away from the objects that are resonating.
The selected
Could the SMF Play
sound changes
Mode be set to
Set the SMF Play Mode to “External.”
when you play
“Internal”?
back a song
Song does not play correctly
Could you be
Some of the Piano Designer settings
recording with a tone
might not be reproduced when you
The piano’s
that you created in
play back a song.
tonal character
Piano Designer?
changes when
Could you be playing
you record
back the audioRecord as SMF.
recorded sound?
Only the sound
of a particular
Could the part button Press the part button so the indicator
instrument in a
be unlit?
is illuminated.
song does not
play
Song volume is
too low / Volume
differs between Could the song volume be set too low?
recording and
playback
Could the Audio files of the format be played?
Audio files of the following format can be played back.
Can’t play back
a song saved in 55 File extension “.WAV”
USB flash drive 55 16-bit linear
55 “44.1 kHz” sampling rate
Is the filename extension “.MID”?
Song name in
Could the song name information in the file be blank or
USB flash drive consist of only spaces?
is not shown
Is the filename extension “.MID”?
Can’t record
Can’t record SMF Has one of the part buttons for recording been selected?
Can’t record
Is a USB flash drive connected to the USB Memory port?
audio
p. 21
–
p. 12
p. 11
p. 20
–
–
–
–
p. 12
–
Error Messages
Problems with Bluetooth functionality
Problem
Items to check/Action
Could the Bluetooth function be turned “Off”?
This unit does not appear
in the Bluetooth device list
If Bluetooth Audio function is “On”
of your mobile device
If the Bluetooth Page Turn function is “On” and
the Bluetooth Turn/MIDI function is “Page Turn” or
“Page Turn&MIDI”
If the Bluetooth Page Turn function is “On” and the
Bluetooth Turn/MIDI function is set to “MIDI” or
“Page Turn&MIDI”
If this unit is visible as a device in the mobile
Can’t connect to Bluetooth device’s Bluetooth settings
audio
If this unit is not visible as a device
Page
Turn the Bluetooth function “On.”
Bluetooth Audio function:
Function mode0“Bluetooth audio”0turn“Bluetooth audio” On
Bluetooth Turn/MIDI function:
Function mode0“Bluetooth Turn/MIDI”0turn “Bluetooth Turn & MIDI (*1)” On
p. 23
(*1) Depending on the Function mode “Bluetooth Turn/MIDI” setting, the screen might indicate
“Bluetooth Page Turn” or “Bluetooth MIDI.”
A device named “GP607 Audio” appears.
A device named “GP607” appears.
–
You can check this from a setting inside your app such as GarageBand.
Delete the device’s registration, turn the Bluetooth Audio function “Off” and then “On”
again, and establish pairing once again.
p. 23
Turn the mobile device’s Bluetooth function off and then on again, and initiate pairing
from this unit to re-establish pairing.
In some cases, the connection with the mobile device might become unavailable when you switch the Bluetooth Turn/MIDI function.
If this unit is not visible as a device in the mobile
After unpairing the “GP607” that is registered on the mobile device, turn the mobile
Can’t connect to Bluetooth
device’s Bluetooth settings
device’s Bluetooth function off and then on again, and reconnect it.
page turning
Turn the mobile device’s Bluetooth function off and on again, and then reestablish the
If this unit is not visible as a device
connection.
In some cases when you switch the Bluetooth Turn/MIDI function, the connection with the mobile device might become unavailable.
Can’t connect to Bluetooth
After unpairing the “GP607” that is registered on the mobile device, turn the mobile device’s Bluetooth function off and then on again, and
MIDI
reconnect it.
You must make the connection not from the mobile device’s Bluetooth setting but from the setting within GarageBand or other app that
Can’t connect via MIDI
you’re using.
Can’t establish pairing with
The page turning function and MIDI function are paired when you first select a device on the mobile device and establish a connection. There
–
the page turning function
is no need to initiate pairing from this unit.
and MIDI function
Can’t use the page turning
function and MIDI function Set the Bluetooth Turn/MIDI function to “Page Turn&MIDI.”
simultaneously
Can’t connect a paired
If the connection breaks immediately after it is established, or when you switch the page turning function and MIDI data transmit/receive
mobile device
function, turning the Bluetooth device’s Bluetooth switch off and then on again may allow connection to occur.
When using the page turning function, the keyboard might not be shown (might be unavailable) depending on the mobile device that you’re
Keyboard no longer
using.
appears (becomes
If you want the mobile device’s keyboard to be shown while you’re using the page turning function, hold down this unit’s [Accomp] button
unavailable) on the mobile
and press the [Left] button.
device
To hide the mobile device’s keyboard, hold down the [Accomp] button and press the [Left] button.
°
Error Messages
Indication
Meaning
Error 2
An error occurred during writing. The external media may be corrupted.
Insert other external media and try again. Alternatively, you can initialize the external media (p. 19).
The internal memory might be damaged. Format the internal memory (p. 19).
Error 10
Error 11
Error 14
No external media is inserted. Insert the external media and try again.
The internal memory might be damaged. Format the internal memory (p. 19).
There is not sufficient free memory in the save destination.
Either insert other external media or delete unneeded files and try again.
An error occurred during reading. The external media may be corrupted.
Insert other external media and try again. Alternatively, you can initialize the external media (p. 19).
The internal memory might be damaged. Format the internal memory (p. 19).
Error 15
The file is unreadable. The data format is not compatible with the unit.
Error 18
This audio format is not supported.
Please use 44.1 kHz 16-bit linear WAV format audio files.
Error 30
Internal memory capacity of the unit is full.
Error 40
The unit cannot deal with the excessive MIDI data sent from the external MIDI device.
Reduce the amount of MIDI data sent to the unit.
Error 43
A MIDI transmission error has occurred. Check the MIDI cable and connected MIDI device.
Error 51
There may be a problem with the system. Repeat the procedure from the beginning. If it is not solved after you have tried several times, contact the Roland
service center.
Error 65
The USB flash drive connector was subjected to excessive current. Make sure that there is no problem with the external media, then turn the power off, then
on again.
27
°
USING THE UNIT SAFELY
WARNING
Concerning the Auto Off function
The power to this unit will be turned off automatically
after a predetermined amount of time has passed
since it was last used for playing music, or its buttons
or controls were operated (Auto Off function). If you
do not want the power to be turned off automatically,
disengage the Auto Off function (p. 22).
Use only the supplied AC adaptor and the correct
voltage
Be sure to use only the AC adaptor supplied with the
unit. Also, make sure the line voltage at the installation
matches the input voltage specified on the AC
adaptor’s body. Other AC adaptors may use a different
polarity, or be designed for a different voltage, so their
use could result in damage, malfunction, or electric shock.
Use only the supplied power cord
Use only the attached power cord. Also, the supplied
power cord must not be used with any other device.
Use due care when handling the lid
• The lid should be opened and closed only by an
adult.
• The lid must not be opened too far (we
recommend that you do not open it by more than
about 30 degrees). If opened to an extreme degree,
you risk damaging the piano or having the lid fall
unexpectedly. Also, when opening the lid, make
sure that no one is in the way.
°
CAUTION
Cautions when moving this unit
Since this product is very heavy, you must make
sure that a sufficient number of people are on hand
to help, so you can lift and move it safely, without
causing strain. Make sure to have a firm grip, to protect
yourself from injury and the instrument from damage.
If you need to move the instrument, take note of the
precautions listed below.
• Check to make sure the screws securing the unit to the stand have
not become loose. Fasten them again securely whenever you
notice any loosening.
• Disconnect the power cord.
• Disconnect all cords coming from external devices.
• Raise the adjusters on the pedal (p. 6).
• Close the lid.
• Close the top.
• Fold down the music stand.
Take care so as not to get fingers pinched
When handling the following moving parts, take care
so as not to get fingers, etc., pinched. An adult should
always be in charge of handling these items.
• Top (p. 4)
• Music rest (p. 4)
• Top stick (p. 4)
• Lid (p. 5)
Keep small items out of the reach of children
To prevent accidental ingestion of the parts listed
below, always keep them out of the reach of small
children.
• Included Parts
Screws
CAUTION
Precautions concerning use of bench
When using the bench, please observe the following
points:
• Do not use the bench as a toy, or as a stepping
stool.
• Do not allow two or more persons to sit on the
bench.
• Do not adjust the height while sitting on the
bench.
• Do not sit on the bench if the bolts holding the
bench legs are loose. (If the bolts are loose, immediately retighten them using the supplied tool.)
• Never insert your hand into the gap (the metal height adjustment
mechanism) under the seat lid. Doing so may cause your hand to
be pinched or injured.
Use due care when handling the lid and cover
• To prevent the lid from dropping, always make sure
to lock the top stick in its receptacle. Also, make
sure to keep supporting the lid with your hands
until the top stick is securely locked.
• When opening and closing the lid, use due caution
so as not to get your fingers pinched. Whenever a
child uses the unit, an adult should be on hand to
provide guidance and supervision.
• Do not close the cover if there are any objects, such
as sheet music, remaining on top of the keyboard.
• As a safety precaution, always make sure to lower
the lid and close the cover before moving the
piano.
IMPORTANT NOTES
Placement
• Do not allow lighting devices that normally are used while their
light source is very close to the unit (such as a piano light), or
powerful spotlights to shine upon the same area of the unit for
extended periods of time. Excessive heat can deform or discolor
the unit.
• Do not allow objects to remain on top of the keyboard. This can
be the cause of malfunction, such as keys ceasing to produce
sound.
Maintenance
• The pedal and hinge of this unit are made of brass. Brass
eventually darkens as the result of the natural oxidization process.
If the brass becomes tarnished, polish it using commercially
available metal polisher.
Care of the Keyboard
• Do not write on the keyboard with any pen or other implement,
and do not stamp or place any marking on the instrument. Ink will
seep into the surface lines and become unremovable.
• Do not affix stickers on the keyboard. You may be unable to
remove stickers that use strong adhesives, and the adhesive may
cause discoloration.
• To remove stubborn dirt, use a commercially available keyboard
cleaner that does not contain abrasives. Start by wiping lightly.
If the dirt does not come off, wipe using gradually increasing
amounts of pressure while taking care not to scratch the keys.
Concerning the Care of the Unit (Mirror Finish)
• The surface of this unit has been polished so as to create a highgloss, mirror-like finish. Since this beautiful finish is as delicate
as that of the highest quality, wood-crafted furniture, it needs to
be cared for at regular intervals. Please make sure to observe the
following when caring for the unit.
• For routine care, gently clean the surface using a soft cloth or
a piano-use feather duster. You must avoid applying any force,
since even the tiniest particles of sand or grit can produce
scratches if you wipe too hard.
• If the finish loses its luster, use a soft cloth dampened with
some polishing liquid to evenly wipe the surface of the unit.
• Avoid using detergents or other cleaners, as they can
cause the surface finish to deteriorate. This may lead to the
formation of cracks or other imperfections. Also, do not use
chemically-enhanced cleaning cloths.
• Precautions concerning the use of polishing agents
• Refer to the instructions that came with the polishing agent
for instructions on its proper use.
• Use only polishing agents that are designed specifically for use
on the mirror finishes of pianos. By using any other product,
you risk causing scratches, deformation, discoloration, etc. To
purchase an appropriate product, please consult the nearest
musical instrument store.
• Use the product only on the portions of this unit that have a
mirror-like finish, and using an even touch, apply it equally
over the entire surface. If you apply more force in one place
over another, you risk losing some of the luster of the finish.
• Store in a location that is out of the reach of small children. If
accidentally ingested, induce vomiting immediately. Then, see
a doctor to obtain a diagnosis.
Repairs and Data
• Before sending the unit away for repairs, be sure to make a
backup of the data stored within it; or you may prefer to write
down the needed information. Although we will do our utmost to
preserve the data stored in your unit when we carry out repairs,
in some cases, such as when the memory section is physically
damaged, restoration of the stored content may be impossible.
Roland assumes no liability concerning the restoration of any
stored content that has been lost.
Additional Precautions
• Note when placing a mobile device such as a smartphone or
tablet on this unit
• Handle your device with care to avoid scratching the unit or
the mobile device.
• To prevent your mobile device from overturning or falling, do
not move the music rest or the cover.
• Any data stored within the unit can be lost as the result of
equipment failure, incorrect operation, etc. To protect yourself
against the irretrievable loss of data, try to make a habit of
creating regular backups of the data you’ve stored in the unit.
• Roland assumes no liability concerning the restoration of any
stored content that has been lost.
• Never strike or apply strong pressure to the display.
• The sound of keys being struck and vibrations produced by
playing an instrument can be transmitted through a floor or wall
to an unexpected extent. Please take care not to cause annoyance
to others nearby.
• Do not apply undue force to the music stand while it is in use.
• Do not use connection cables that contain a built-in resistor.
Using External Memories
• Please observe the following precautions when handling external
memory devices. Also, make sure to carefully observe all the
precautions that were supplied with the external memory device.
• Do not remove the device while reading/writing is in progress.
• To prevent damage from static electricity, discharge all static
electricity from your person before handling the device.
Caution regarding radio frequency emissions
• The following actions may subject you to penalty of law.
• Disassembling or modifying this device.
• Removing the certification label affixed to the back of this
device.
Intellectual Property Right
• It is forbidden by law to make an audio recording, video
recording, copy or revision of a third party’s copyrighted work
(musical work, video work, broadcast, live performance, or other
work), whether in whole or in part, and distribute, sell, lease,
perform, or broadcast it without the permission of the copyright
owner.
• Do not use this product for purposes that could infringe on a
copyright held by a third party. We assume no responsibility
whatsoever with regard to any infringements of third-party
copyrights arising through your use of this product.
• The copyright of content in this product (the sound waveform
data, style data, accompaniment patterns, phrase data, audio
loops and image data) is reserved by Roland Corporation.
• Purchasers of this product are permitted to utilize said content
(except song data such as Demo Songs) for the creating,
performing, recording and distributing original musical works.
• Purchasers of this product are NOT permitted to extract said
content in original or modified form, for the purpose of distributing
recorded medium of said content or making them available on a
computer network.
• This product contains eParts integrated software platform of eSOL
Co.,Ltd. eParts is a trademark of eSOL Co., Ltd. in Japan.
• The Bluetooth® word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks by
Roland is under license.
• This Product uses the Source Code of μT-Kernel under T-License
2.0 granted by the T-Engine Forum (www.tron.org).
• Roland, SuperNATURAL, BOSS are either registered trademarks
or trademarks of Roland Corporation in the United States and/or
other countries.
• Company names and product names appearing in this document
are registered trademarks or trademarks of their respective
owners.
• This product is using the Jansson (http://www.digip.org/jansson/)
source code.
Copyright © 2009-2014 Petri Lehtinen <[email protected]>
Released under the MIT license http://opensource.org/licenses/
mit-license.php
28
°
Tone List
Piano
No.
1
2
3
4
Other
Tone Name
Concert Piano
Ballad Piano
Mellow Piano
Bright Piano
MEMO
Piano Designer can be used to customize the sound only for tones of the [Piano]
button.
E. Piano
No.
1
2
3
4
5
6
7
8
9
10
Tone Name
Tremolo EP
Pop EP
Vintage EP
FM E.Piano
EP Belle
‘60s EP
Clav.
Stage Phaser
‘70s EP
E.Grand
Organ
No.
1
2
3
4
5
6
7
8
9
10
11
12
Tone Name
Pipe Organ
Nason flt 8’
Combo Jz.Org
Ballad Organ
ChurchOrgan1
ChurchOrgan2
Gospel Spin
Full Stops
Mellow Bars
Light Organ
Lower Organ
‘60s Organ
Strings
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Tone Name
Symphonic Str 1
Epic Strings
Rich Strings
Orchestra Str
Orchestra
Chamber Winds
Harp
Violin
Velo Strings
Flute
Cello
OrchestraBrs
Pizzicato Str
Symphonic Str 2
Soft Pad
Magical Piano
Jazz Scat
No.
1
2
3
4
5
6
7
8
9
10
Tone Name
UprightPiano
MellowUprght
BrightUprght
Rock Piano
RagtimePiano
Fortepiano
Mellow Forte
Bright Forte
Harpsichord
Harpsi 8’+4’
* If you select tone numbers 11–19, you’ll be able to use the keyboard to play the
sounds of a drum set.
* Tones numbered 20 and higher are accompaniment-use GM2 tones.
* In the tone group “Other” when you hold down the [–] [+] buttons to switch tone
in succession, the tones will stop changing at number 6, number 11, and number
20.
* To select the next sound, release the [–] [+] buttons, then press it again.
°
Internal Song List
No.
Song Title
Listening
Composer
Robert Alexander Schumann,
Arranged by Franz Liszt
Fryderyk Franciszek Chopin
Léo Delibes, Arranged by John Maul
1
Widmung S.566 R.253
2
3
Étude, op.10-12
Floral Pursuits *
The Nutcracker “Waltz of the
Peter Ilyich Tchaikovsky
Flowers” (Jazz Arrangement) *
The Marriage of Figaro
Wolfgang Amadeus Mozart
“Overture” (Piano Arrangement) *
4
5
6
Barcarolle
7
Zhavoronok
8
9
10
11
12
13
Sonate für Klavier Nr.23 1
Sonate für Klavier Nr.23 2
Sonate für Klavier Nr.23 3
Valse, op.34-1
Polonaise op.53
Nocturne No.20
14
Die Forelle
15
Reflets dans l'Eau
16
La Fille aux Cheveux de Lin
17
La Campanella
18
Scherzo No.2
Masterpieces
1
Danse des Mirlitons *
2
Salut d'amour *
3
Menuett G Dur BWV Anh.114
4
Präludium C Dur BWV846
5
The Harmonious Blacksmith
6
Le Coucou
7
Türkischer Marsch
8
Sonate Nr.16 C Dur
9
Türkischer Marsch
10
Für Elise
11
Moments Musicaux op.94-3
12
Gavotte
13
Sonatine op.36-1
14
Sonatine op.20-1
15
Jägerlied
16
Frühlingslied
17
Auf Flügeln des Gesanges
18
Nocturne, op.9-2
19
Étude, op.10-3
20
Prélude, op.28-15
21
Valse, op.64-1
22
Valse, op.64-2
23
Fantaisie-Impromptu
24
Radetzky Marsch
25
Träumerei
26
Fröhlicher Landmann
27
La prière d'une Vierge
28
Dolly's Dreaming Awakening
29
Brautchor
30
Liebesträume Nr.3
31
Blumenlied
32
Course en Troïka
33
Ungarische Tänze Nr.5
34
An der schönen, blauen Donau
35
Humoreske
36
Clair de Lune
37
1ère Arabesque
38
Golliwog's Cakewalk
39
Je te veux
40
1ère Gymnopédie
Easy Piano
1
Twinkle Twinkle Little Star
2
Mary Had a Little Lamb
3
Bear Song
4
Ich Bin Ein Musikante
5
Grand Father's Clock
6
Maple Leaf Rag
Le Quattro Stagioni “La
7
Primavera”
8
Marche Militaire Nr.1
Scales
1–36
Major Scales, Minor Scales
Hanon
1–20
Hanon 1–20
Beyer
1–106 Beyer 1-106
Fryderyk Franciszek Chopin
Mikhail Ivanovich Glinka,
Arranged by Mily Alexeyevich Balakirev
Ludwig van Beethoven
Ludwig van Beethoven
Ludwig van Beethoven
Fryderyk Franciszek Chopin
Fryderyk Franciszek Chopin
Fryderyk Franciszek Chopin
Franz Peter Schubert,
Arranged by Franz Liszt
Claude Achille Debussy
Claude Achille Debussy
Franz Liszt
Fryderyk Franciszek Chopin
Peter Ilyich Tchaikovsky
Edward Elgar
Johann Sebastian Bach
Johann Sebastian Bach
Georg Friedrich Händel
Louis Claude Daquin
Wolfgang Amadeus Mozart
Wolfgang Amadeus Mozart
Ludwig van Beethoven
Ludwig van Beethoven
Franz Peter Schubert
François Joseph Gossec
Muzio Clementi
Friedrich Kuhlau
Felix Mendelssohn
Felix Mendelssohn
Felix Mendelssohn
Fryderyk Franciszek Chopin
Fryderyk Franciszek Chopin
Fryderyk Franciszek Chopin
Fryderyk Franciszek Chopin
Fryderyk Franciszek Chopin
Fryderyk Franciszek Chopin
Johann Baptist Strauss
Robert Alexander Schumann
Robert Alexander Schumann
Tekla Badarzewska
Theodor Oesten
Wilhelm Richard Wagner
Franz Liszt
Gustav Lange
Peter Ilyich Tchaikovsky
Johannes Brahms
Johann Strauss, Sohn
Antonín Dvořák
Claude Achille Debussy
Claude Achille Debussy
Claude Achille Debussy
Erik Satie
Erik Satie
French Folk Song
Traditional
American Folk Song
German Folk Song
Henry Work
Scott Joplin
Antonio Vivaldi
Franz Peter Schubert
–
Charles-Louis Hanon
Ferdinand Beyer
No.
Song Title
Burgmüller
1
Openness
2
Arabesque
3
Pastoral
4
A Small Gathering
5
Innocence
6
Progress
7
The Clear Stream
8
Gracefulness
9
The Hunt
10
Tender Flower
11
The Young Shepherdess
12
Farewell
13
Consolation
14
Austrian Dance
15
Ballad
16
Sighing
17
The Chatterbox
18
Restlessness
19
Ave Maria
20
Tarantella
21
Angelic Harmony
22
Gondola Song
23
The Return
24
The Swallow
25
The Knight Errant
Czerny100
1–100 Czerny100 1-100
Composer
Johann Friedrich Franz Burgmüller
Carl Czerny
* All rights reserved. Unauthorized use of this material for purposes other than
private, personal enjoyment is a violation of applicable laws.
* The performance data for the tone demos and the internal songs is not transmitted
from the USB Computer port or via Bluetooth (MIDI).
* If the SMF Play Mode is set to “Internal,” there will be some parts whose volume does
not change when you adjust the Song Volume SMF value. If the SMF Play Mode is
set to “External,” the volume of all parts will change.
* Songs marked by an asterisk (*) are arranged by Roland Corporation. The copyrights
to these songs are owned by the Roland Corporation.
* Listening 1, 2, 6–18 are piano solos. They have no accompaniment.
For the USA
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
(FCC Part15 Subpart C ¤15.247, 15.253, 15.255)
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC
radio frequency (RF) Exposure Guidelines. This equipment has very low levels of RF energy that it deemed to comply
without maximum permissive exposure evaluation (MPE).
(FCC Part15 Subpart C ¤15.247, 15.253, 15.255)
For Canada
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Le prŽsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisŽe aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur
de l'appareil doit accepter tout brouillage radioŽlectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
(RSS-Gen ¤7.1.3)
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of
the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply
without maximum permissive exposure evaluation (MPE).
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et
respecte les règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie
RF très faible qui est considérée conforme sans évaluation de l’exposition maximale autorisée.
(RSS-102 ¤2.6)
For EU countries
European Community Declaration of Conformity
Hereby, Roland Corporation, declares that this GP607 is in compliance with the essential requirements and other relevant provisions of Directive
2014/53/EU.
English
Bulgarian
Czech
Danish
German
Estonian
Greek
Spanish
French
Italian
Latvian
Lithuanian
Hungarian
Dutch
Polish
Portuguese
Romanian
Hereby, Roland Corporation, declares that this GP607 is in compliance with the essential requirements and other relevant
provisions of Directive 2014/53/EU.
С настоящето, Roland Corporation, декларира, че GP607 е в съответствие със съществените изисквания и
другитеприложими разпоредби на Директива 2014/53/EU.
Roland Corporation tímto prohlašuje, že GP607 splňuje základní požadavky a všechna příslušná ustanoveni Směrnice 1999/5/ES.
Undertegnede Roland Corporation erklærer herved, at følgende udstyr GP607 overholder de væsentlige krav og øvrige relevante
krav i direktiv 1999/5/EF.
Hiermit erklärt Roland Corporation, dass sich das Gerät GP607 in Übereinstimmung mit den grundlegenden Anforderungen und
den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.,
Käesolevaga kinnitab Roland Corporation seadme GP607 vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist
tulenevatele teistele asjakohastele sätetele.
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Roland Corporation ΔΗΛΩΝΕΙ ΟΤΙ GP607 ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ
ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ
Por la presente, Roland Corporation, declara que este GP607 cumple con los requisitos esenciales y otras exigencias relevantes de
la Directiva 2014/53/EU.
Par la présente, Roland Corporation déclare que l’appareil GP607 est conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 1999/5/CE.
Con la presente Roland Corporation dichiara che questo GP607 è conforme ai requisiti essenziali ed alle altre disposizioni
pertinenti stabilite dalla direttiva 1999/5/CE.
Ar šo Roland Corporation deklarē, ka GP607 atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem
noteikumiem.
Šiuo Roland Corporation deklaruoja, kad šis GP607 atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas
A Roland Corporation ezzennel kijelenti, hogy a GP607 típusú beren-dezés teljesíti az alapvető követelményeket és más 1999/5/EK
irányelvben meghatározott vonatkozó rendelkezéseket.
Hierbij verklaart Roland Corporation dat het toestel l GP607 in overeenstemming is met de essentiële eisen en de andere relevante
bepalin-gen van richtlijn 1999/5/EG.
Niniejszym Roland Corporation deklaruje że GP607 jest zgodny z zasadniczymi wymaganiami i innymi właściwymi
postanowieniami Dyrektywy 2014/53/EU.
Eu, Roland Corporation, declaro que o GP607 cumpre os requisitos essenciais e outras provisões relevantes da Directiva 2014/53/
EU.
Prin prezenta, Roland Corporation, declară că aparatul GP607 este în conformitate cu cerinţele esenţiale şi cu alte prevederi
pertinente ale Directivei 1999/5/CE..
Slovak
Roland Corporation týmto vyhlasuje, že GP607 spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.
Slovenian
Roland Corporation izjavlja, da je ta GP607 v skladu z bistvenimi zahtevami in drugimi relevantnimi določili direktive 1999/5/ES.
Finish
Roland Corporation vakuuttaa täten että GP607 tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien
direktiivin muiden ehtojen mukainen.
Swedish
Härmed intygar Roland Corporation att denna GP607 står I överensstämmelse med de väsentliga egenskapskrav och övriga
relevanta bestämmelser som framgår av direktiv 1999/5/EG.
The Declaration of Conformity may be consulted in Downloads menu of this product at www.roland.com.
This unit has an RF transmitter(s) with the following specification.
55 Operating frequency: 2400–2483.5 MHz
55 Maximum RF transmit power: 2.5 mW
*
5
1
0
0
0
5
3
3
5
9
-
0
2
*
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement