SingingMachine SDL9050 User manual

SDL9050
FESTIVAL
INSTRUCTION MANUAL
www.singingmachine.com
The Singing Machine® is a registered trademark of The Singing Machine Co.,Inc.
Warnings
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT AND FULLY INSERT.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The Caution marking is located on the bottom panel.
DANGEROUS VOLTAGE: The lightning flash with arrowhead
symbol within an equilateral triangle is intended to alert the
user to the presence of uninsulated dangerous voltage within
the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
ATTENTION: The exclamation point within an equilateral
triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions
in the literature accompanying this product.
DRIPPING WARNING: This product shall not be exposed to dripping or
splashing, and no objects filled with liquids, such as vases, shall be placed
on the product.
This symbol on the product or in the instructions means that your electrical
and electronic equipment should be disposed of at the end of its life
separately from your household waste. There are separate collection
systems for recycling in the EU.
For more information, please contact the local authority or your retailer
where you purchased the product.
Under the influence of electrostatic phenomenon, the product may
malfunction and require user to reset.
VENTILATION WARNING: The normal ventilation of the product shall not be
impeded for intended use.
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
Main plug is used as disconnect device and it should remain readily operable
during intended use. In order to disconnect the apparatus from the mains
completely, the main plug should be disconnected from the main socket
outlet completely.
Important Safety Information
1.
Read these Instructions.
2.
Keep these Instructions.
3.
Heed all Warnings.
4.
Follow all Instructions.
5.
Do not use this apparatus near water.
6.
Clean only with a dry cloth.
7.
Do not block any of the ventilation openings. Install in accordance
with the Manufacturer’s instructions.
8.
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9.
Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. When the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete
outlet.
12. Use only with a cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
14. Refer all servicing to qualified service
personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
15. WARNING: To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture. Do not place objects
filled with water, such as a vase, on the apparatus.
16. The AC mains plug is used as the power disconnect device and
it should remain readily accessible and operable during intended
use. In order to completely disconnect the apparatus from
power, the mains plug should be completely removed from the
AC outlet socket.
17. CAUTION: To reduce the risk of fire or explosion, do not expose
batteries to excessive heat such as sunshine, fire or other
heat sources.
— E1 —
Included
Please make sure the following items are included.
Main Unit
Wired Microphone x2
AC Adapter
Manual
— E2 —
Location of Controls (Top/Front)
u
v
w
x
y
U
V
W
aq
ar
as
bt
bk
bl
bm
X
bn
bo
am
X
at
ak
al
am
an
ao
ap
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
bp
bq
br
Disco Ball
TFT LCD Color Screen
VOCAL/PAIR Button
FUNCTION (Monitor ON/OFF) Button
MENU Button
RECORD  Button
ON/STANDBY Button
DISCO BALL Button
MIC Holder
EXTERNAL INPUT VOLUME Control
MIC 1 VOLUME Control
EXTERNAL INPUT Jack
Tweeter
LINE IN Jack
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
— E3 —
Bluetooth Indicator
MASTER VOLUME Control
Navigation LEFT 3 Button
Navigation UP 5 Button
Navigation RIGHT 4Button
Navigation DOWN 6Button
ENTER/
Button
LIGHT MODE Button
ECHO Control
MIC 2 VOLUME Control
MIC 2 Jack
MIC 1 Jack
USB Slot
Speaker/Lights
Location of Controls (Rear)
u
v
w
1. Handle
2. DC IN Jack
3. HDMI Jack
Location of Controls (Playback Display)
Song Title
Song
Elapsed Time
Song
Total Time
Current
Playlist
Lead Vocal Status
Record Status
Playback Status
Battery
Status
Master Volume: 0-20
Echo Control: 0-8
— E4 —
Connection
Connecting the Microphone(s)
Microphones:
Connect a microphone into Mic jack 1 u
and the other microphone into Mic jack 2
v (if desired).
Note: Do not drop or tap the Mic as
damage to the Mic or speakers may occur.
Do not twirl the microphone by cord as it
will cause damage to the encased wiring.
v
u
Connecting the Unit to a TV
The video and lyrics will be displayed
on the built-in screen. You may also
want to connect a TV to display a
larger image and additional sound;
follow the steps below:
Rear of External TV
HDMI Jack (In)
HDMI IN
1
HDMI Jack (Out)
HDMI Cable
— E5 —
2
Plug the HDMI cable (Not included)
into the HDMI Jack on the back of
the unit. Plug the other end of the
HDMI cable into the HDMI input on
your TV.
Notes:
• This unit can be used with or
without a TV.
• Also refer to the TV’s or external
unit’s User Guide.
Connection
Connecting to AC Power
1
Insert the AC power cord
into a conveniently located
AC outlet having 230V,
50Hz.
Note:
Make all connections before
connecting to AC power.
Energy Saving (Auto Power System-APS)
The unit will automatically enter the Standby mode after 15 minutes in the following
situations:
1. There is no video or audio playback on USB/Bluetooth/Recordings/Line in mode;
2. The playback of external music player had been stopped but the audio cable is still
plugged into the LINE IN jack.
The unit can be resumed to turn on by pressing the ON/STANDBY button once.
APS is for energy saving purposes.
— E6 —
Rechargeable Battery
This unit comes with a built-in rechargeable battery pack that will allow the unit to be used
without being connected to AC power. The Battery indicator (top right of the display) will
show the battery charge left indicated by the amount of bars. The rechargeable battery
pack must NOT to be replaced by the user.
To optimize the battery life, we recommend to charge the unit once a month. When the
battery icon turns red and flashing, recharge the unit by following the steps below:
1
Insert the AC power cord into
a conveniently located AC
outlet having 230V, 50Hz.
2
Allow the unit to charge for
approximately twelve hours
for a full charge.
3
Disconnect the AC cord and
the fully charged unit can
be used for approximately
five hours depending on the
function chosen.
Attention: The sound volume will adjust automatically when the battery is not full.
The symbol shown here and on the product means that the product is classed as
Electrical or Electronic Equipment and should not be disposed with other
household or commercial waste at the end of its working life.
The Waste Electrical and Electronic Equipment (WEEE) Directive (2012/19/EU) has
been put in place to encourage the recycling of products using best available recovery
and recycling techniques to minimise the impact on the environment, treat any hazardous
substances and avoid the increase of landfill.
When you have no further use for this product, please dispose of it using your local authority’s
recycling processes. For more information, please contact your local authority or the retailer
where the product was purchased.
Lead Acid Battery Warning
• This equipment contains a rechargeable valve-regulated lead acid battery.
• Do not charge the battery in temperatures below 32° F (0° C) or higher than 122° F (50°
C).
• Do not open or mutilate the battery.
• The rechargeable batteries contained in this equipment may explode if disposed of in a fire.
• Do not short-circuit the battery.
• Do not charge the rechargeable battery pack used in this equipment with any charger other
than the one designed to charge this battery pack, as specified in the owner’s manual. Using
another charger may damage the battery pack or cause the battery pack to explode.
— E7 —
Karaoke Store
PC Installation
The Karaoke Store application can be installed on Microsoft Windows computers running
Vista, Windows 7, and Windows 8 or higher. The Karaoke Store application requires
connection to the Internet (a high-speed connection is recommended).
1
Insert the USB Flash Drive into
a powered USB slot on your
computer.
2
Double-click the file named,
“Karaoke_Store_Win_Setup”.
3
Follow the online instructions to install the
software on your computer.
4
After installing, open your Program’s folder
and open the Karaoke Store folder.
5
Double-click “Karaoke Store”
to open the software.
6
On this page you can now sign
up and purchase/download
them to your computer and/or
USB drive for playing on your
new Singing Machine!
— E8 —
Karaoke Store
Mac Installation
The Karaoke Store application can be installed on Apple Macintosh computers running OS X
10.8 and higher. The Karaoke Store application requires connection to the Internet (a highspeed connection is recommended).
1
Insert the USB Flash Drive into
a powered USB slot on your
computer.
2
Double-click the file named,
“Karaoke_Store_Mac_Setup.pkg”.
3
Follow the online instructions
to install the software on your
computer.
4
After installing, open your
Application’s folder and open the
Stingray Karaoke Store folder.
5
Double-click Karaoke Store
App to open the software.
6
On this page you can now sign
up and purchase/download
them to your computer and/or
USB drive for playing on your
new Singing Machine!
— E9 —
Operation
Light Mode
1
There are four Light modes.
Repeatedly press the LIGHT MODE
button to select a mode as follows:
Light Modes 1: The unit will synchronize
to the music being played.
v
u
Light Mode 2: The unit will light up with
random colors and patterns.
Light Mode 3: The light effects will be
turned off.
2
This unit also comes with a Disco
Ball feature. Press the DISCO BALL
button to turn the lights on and they
will illuminate onto the ceiling.
Power Save Mode
u
To save the battery power of the
unit when you are outdoor, the TFT
screen will turn off after 30 seconds
of no action. The sound volume level
will also adjust automatically with the
rechargeable battery level.
You can also press and hold the FUNC
button u to turn off the TFT screen
whenever you want.
Turning the TFT Monitor Off
1
u
— E10 —
To turn the built-in TFT monitor Off;
press and hold the FUNC button until
the built in TFT monitor turns off.
Repeat the same step to turn the
built-in TFT monitor ON.
Operation
Playing Songs from the USB
u
v
1
Connect the unit as described
previously. Press the ON/STANDBY
button to turn the unit on.
2
Insert a USB flash containing MP3 or
MP4 files drive into the USB port on
the unit so it faces upward. We have
a large selection of karaoke music
available for download through our
Karaoke Store.
3
The USB mode will be selected by
default; press the ENTER
button
to enter the USB mode. You can also
repeatedly press the FUNC button to
select the USB mode.
Notes:
• The USB mode cannot be accessed
until a flash drive is inserted.
w
USB
BLUETOOTH®
Sing your Karaoke Songs
Listen to Music
RECORDINGS
Play your Recordings
LINE-IN
Playback
will appear on
• A loading icon
the external screen when the system is
loading the songs.
— E11 —
Operation
Playing Songs from the USB (Continued)
4
x
y
Use the NavigationUp and 
Down buttons to navigate through
the list of songs that you have
previously downloaded on your USB.
U
5
Press the ENTER
button to start
the playback. The HD karaoke video
will play on the screen. Press the
ENTER
button during playback
to pause the song. Press the MENU
button to stop the playback and go
back to the USB menu.
Notes:
• If connected to a TV, there will be no
display on the built-in monitor.
• If connected to a TV, you can also
control the volume with the TV’s
volume control.
V
6
Adjust the volume to a comfortable
level using the MASTER VOLUME
control.
7
Connect microphone(s) and slide the
ON/OFF switch on the microphone
to the ON position.
W 8
— E12 —
Adjust the MIC VOLUME 1 or 2
control as desired. Increasing this will
increase the volume of the respective
microphone(s).
Operation
Playing Songs from the USB (Continued)
9
at
X
ak
al
Rotate the ECHO control to add
an echo effect to your voice.
Rotate towards MAX to increase
the echo effect.
10
VOCALS: To sing with the lead
singer on the recording, press
the VOCAL/PAIR button; “ ”
will appear at the top right of the
monitor. To listen to music only,
press the VOCAL/PAIR button
again; “ ” will appear over the
Lead Vocal Status icon.
Note: The song must be recorded with
separate vocals that is downloaded (aka
multiplex recording) in order to utilize the
Lead Vocal function.
11
SKIP: Advance or go backone
track by pressing the
NavigationRight orLeft
button.
12
TO ADVANCE ON THE TRACK:
During playback, press and
hold the NavigationRight or
Left button to move forward
or backward. When you release
the button, normal playback will
resume.
— E13 —
Operation
Playing Songs from the USB (Continued)
13
SEARCHING BY ARTIST
OR TITLE: While in the USB
menu, select Search using
the NavigationLeft and
Right buttons, then press
the ENTER
button. The
alphabet will appear at the
bottom of the screen. Select the
desired starting letter using the
MASTER VOLUME control, then
press the ENTER
button
to select it. A list of songs that
meet the criteria will appear.
Use the Navigation Up and
Down buttons to navigate
through the list of songs, then
press the ENTER
button to
play your selection, or select the
next letter the same way.
Note:
You can search up to six letters; after the
sixth letter the search will reset.
— E14 —
Operation
Playing Songs from the USB (Continued)
14
SEARCHING BY GENRE, ARTIST
or TITLE: To filter by Genre, Artist
or Title, select the Genre, Artist, or
Title using the NavigationLeft
andRight buttons, then press the
ENTER
button. The alphabet
will appear at the bottom of the
screen; select the desired starting
letter using the MASTER VOLUME
control, then press the ENTER
button to select it. A list of songs
that meet the criteria will appear.
Use the Navigation  Up and 
Down buttons to navigate through
the list of songs, then press the
ENTER
button to play your
selection, or select the next letter
the same way.
Note:
You can search up to six letters. After the
sixth letter the search will reset.
Add
Added
15
CREATING THE PLAYLIST: To
create a personalized playlist,
select a song using the Navigation
Up and Down buttons, then
scroll to the Playlist column (Add)
using the NavigationRight or
Left button. Press the ENTER
button to confirm the operation;
“Added” will appear. Repeat this
step to add more songs.
Notes:
• The personalized Playlist will be kept even
if the unit is turned on or off.
• You can always edit your Playlist after
you create it by selecting a song that
was added and pressing the ENTER
button again; “Added” will change to
“Add”.
— E15 —
Operation
Playing Songs from the USB (Continued)
16
— E16 —
USING THE PLAYLIST: To play your
previously created playlist, select
Playlist using the NavigationRight
andLeft buttons, then press the
ENTER
button; the row under
Playlist will be highlighted. Select the
desired selection using the Navigation
Right andLeft buttons as follows:
TO PLAY ALL: Select Play All and
then press the ENTER
button to
play back all of the Playlist songs. (See
below to add favorites.)
PRIORITY:
a. Select priority and then navigate
down to the song you want to
prioritize.
b. Press the NavigationRight button
and the numbers will change to 0001,
0002, etc. According to the numbers
displayed the songs will be listed in that
order from top to bottom.
c. After setting all songs on your
priority list, press the MENU button
then the playlist will be highlighted.
d. Use the Navigation  Down button
to select the first song and press
button to start the
the ENTER
playback of all songs on the play list.
e. To change the Priority list, navigate
up and down to select the songs you
want to play in the order you desire.
REMOVE: Select Remove and then
select a song to remove using the
Navigation  Up and  Down
buttons. Press the ENTER
button;
the song will be deleted from the
playlist.
RM ALL: To remove the whole Playlist,
select RM ALL and then press the
ENTER
button; the whole Playlist
will be deleted.
Operation
Playing Songs from the USB (Continued)
17
as
<PLAY ALL>
<PRIORITY>
<RM ALL>
<REMOVE>
CREATING FAVORITES: To
create a favorite playlist, select a
song using the Navigation Up
and Down buttons, then scroll
to the Favorite column using the
NavigationRight or Left
button. Press the ENTER
button to confirm the operation;
the icon will turn from white to
blue. Repeat this step to add more
songs.
Notes:
• The Favorites will be stored even if the
unit is turned on or off.
• You can always edit Favorites after you
create them by selecting a song that
was added and pressing the ENTER
button again; it will change from blue to
white.
18
USING THE PLAYLIST: To play
or edit your previously created
Favorite playlist, you can use the
NavigationRight and Left
buttons to select the Favorite tag.
Then press the ENTER
button
to show the favorites list. Perform
the same steps as shown in the
USING THE PLAYLIST section on the
previous page to play and edit the
Favorite playlist.
19
Press the ON/STANDBY button to
turn the unit off.
Note:
When in the Menu screen, press the MENU
button to go back and change categories;
i.e. while in the Playlist column press the
MENU button to go back and then select
the Artist column, etc.
— E17 —
Operation
Using a Bluetooth Device
1
Connect the unit as described previously.
Press the ON/STANDBY button to turn
the unit on.
2
Press the NavigationRight or  Left
button to select the Bluetooth mode,
then press the ENTER
button. You
can also repeatedly press the FUNC
button to select the Bluetooth mode.
The Bluetooth indicator will blink to
show the unit is ready to pair and “Please
connect your Music Device” will appear
in the monitor.
v
v
u
3
Please connect your Music Device
Your Music Device is connected
Turn on your device’s Bluetooth option
in settings to search for a discoverable
device with a Bluetooth signal. Select
“Singing Machine” from the device
results on the Bluetooth menu.
Note:
• Always refer to the user manual of your
Bluetooth device for detailed instructions.
• You can also press the VOCAL/PAIR
button to disconnect any paired devices in
order to pair another device.
4
3
4
The Bluetooth indicator will light solid,
a tone will sound and the monitor
will display ”Your Music Device is
connected”.
Notes:
• If your Bluetooth device prompts you for a
passcode during the pairing process, please
enter “0000” to connect.
• On some Bluetooth devices, once pairing is
complete, select your Bluetooth device as
“Use as Audio Device” or similar.
• If connection is lost after successful
pairing, check to make sure the distance
between speaker and Bluetooth-enabled
device does not exceed 30 ft/10 meters.
— E18 —
Operation
Using a Bluetooth Device (Continued)
Note: You can view the lyrics on your mobile device/tablet and get more songs by
downloading the “The Singing Machine Mobile Karaoke App”; refer to the Welcome Kit for
full app download instructions.
5
y
U
V
6
Adjust the volume to a
comfortable level using the
MASTER VOLUME control on
this unit as well as the Volume on
your Bluetooth device.
Note: If connected to a TV, you can
adjust the TV’s volume as well.
7
Connect microphone(s) and
slide the ON/OFF switch on the
microphone to the ON position.
8
Adjust the MIC VOLUME 1 or 2
control as desired. Increasing this
will increase the volume of the
the respective microphone(s).
9
Rotate the ECHO control to add
an echo effect to your voice.
Rotate towards MAX to increase
the echo effect.
10
SKIP: Advance or go back one
track by pressing the Navigation
Right or Left button.
at
X
You can control your Bluetooth
device to start the music playback
OR press the ENTER
button to start playback. Press
the ENTER
button during
playback to pause the song.
W
— E19 —
Operation
Using a Bluetooth Device (Continued)
11
ak
RECORD YOUR VOCAL
PERFORMANCE:
To record your singing as well as
the music, press the REC button.
Recording will begin and the
record icon at the bottom right
corner of the monitor will blink
red and blue.
When done recording, press the
REC button again; the Record icon
will stop blinking.
Notes:
• A USB flash drive must be inserted into
USB slot to record.
• The recorded audio file will record onto
the USB drive.
• The recorded audio file will be named
with the “BT” prefix.
• See section “Playing Songs from the
Recorded Files” to play back your
recorded files.
al
12
— E20 —
Press the ON/STANDBY button
to turn the unit off.
Operation
Playing Songs from the Recorded Files
v
v
1
Connect the unit as described
previously. Press the ON/STANDBY
button to turn the unit on.
2
Press the NavigationRight or
Left button to select the Recordings
mode and press the ENTER
button
to continue. You can also repeatedly
press the FUNC button to select the
Recordings mode.
Notes:
• The Recording mode cannot be entered
unless a USB flash drive is inserted.
u
• A loading icon
will appear when
the system is loading the files.
3
Use the Navigation  Up and
Down buttons to navigate through
the list of recorded files that you have
previously recorded on your USB.
4
Press the ENTER
button to start
the recorded audio file playback. Press
the ENTER
button during playback
to pause the file.
5
Adjust the volume to a comfortable
level using the MASTER VOLUME
control.
3
4
w
x
y
5
— E21 —
Operation
Playing Songs from the Recorded Files (Continued)
U
6
You can sing along with your
previously recorded song. Simply
connect microphone(s) and slide the
ON/OFF switch on the microphone to
the ON position.
7
Adjust the MIC VOLUME 1 or 2
control as desired. Increasing this
will increase the volume of the the
respective microphone(s).
8
Rotate the ECHO control to add an
echo effect to your voice. Rotate
towards MAX to increase the echo
effect.
V
Notes:
• You can search for a title using the same
procedure as shown on page E15.
• You can set and play a Playlist or
Favorite using the same procedure as
shown on pages E16 to E18.
— E22 —
Operation
Using the LINE IN Jack
1
Connect an external unit to the LINE IN
jack. Press the ON/STANDBY button
to turn the unit on.
2
Connect the external unit to the
LINE IN Jack on the front of this unit.
Connecting an external unit will allow
the audio to be played through your
Singing Machine.
Notes:
• It is highly recommended to set the
volume on the auxiliary unit to 1/3 or
lower to avoid distortion.
• Skipping files/tracks is not possible when
using an external device.
u
v
w
w
x
y
3
Press the NavigationRight or
Left button to select the Line In
mode and press the ENTER
button
to continue. You can also repeatedly
press the FUNC button to select the
Line In mode.
4
Adjust the volume using the Master
Volume, TV or external device.
5
Connect microphone(s) and slide the
ON/OFF switch on the microphone to
the ON position.
— E23 —
Operation
Using the LINE IN Jack (Continued)
W
V
6
Adjust the MIC VOLUME 1 or 2
control as desired. Increasing this will
increase the volume of the respective
microphone.
7
Rotate the ECHO control to add an
echo effect to your voice. Rotate
towards MAX to increase the echo
effect.
U
8
RECORDING YOUR SINGING:
To record your singing as well as the
music, press the REC button; recording
will begin and the record icon at the
bottom right of the monitor will blink
red and blue.
When done recording, press the REC
button again; the Record icon will stop
blinking.
Notes:
• A USB flash drive must be inserted into
USB slot to record.
• The recorded audio file will record onto
the USB drive.
• The recorded audio file will be named
with the “LINEIN” prefix.
• See section “Playing Songs from the
Recorded Files” to play back your
recorded files.
X
9
— E24 —
Press the ON/STANDBY button to
turn the unit off.
Operation
Using the EXTERNAL INPUT Jack
u
1
Connect the unit as described
previously. Press the ON/STANDBY
button to turn the unit on.
2
Connect the external unit to the
EXTERNAL INPUT Jack on the front
of this unit. Connecting an external
unit will allow the audio to be played
through your Singing Machine.
v
Notes:
• It is highly recommended to set the
volume on the auxiliary unit to 1/3 and
the EXTERNAL INPUT Volume control
on this unit to 1/3 as well to avoid
distortion.
• Skipping files/tracks is not possible when
using an external device.
3
— E25 —
Play the device connected to the
EXTERNAL INPUT jack and it will play
through this unit regardless of the
function selected.
Troubleshooting Guide
Should this unit exhibit a problem, check the following before seeking service:
No Power
• Power is not on; press the ON/STANDBY button to turn power on.
• Make sure the unit is connected to AC power.
• Confirm the AC adapter is connected securely to the back of the unit
• Connect the unit to a different outlet.
• The unit has no battery left. Connect to AC power to recharge the battery.
No Sound – General
• Master Volume is set to minimum; raise volume.
• Correct Function was not selected; select using the Navigation buttons.
No Sound – If connected to a TV
• Volume on the TV is muted or too low.
• Correct source (HDMI) was not selected on the TV’s menu.
Lyrics do not appear on the TV screen
• If connected to a TV, HDMI plug is not connected properly; see page E5.
• If connected to a TV, select the correct source on the TV (usually HDMI).
• The file/track being played is not a track recording with lyrics. These are the only files
that allow you to view the lyrics on the TV screen.
No sound from the microphone
• Make sure it is firmly connected to the MIC 1 or MIC 2 jack.
• Make sure the Power switch on the Mic is set to the On position.
• Make sure the MIC VOLUME controls are not on the lowest setting.
• MASTER VOLUME is set to minimum; raise volume.
File(s) on USB jack not playing
• The file is corrupted; replace file.
• The file is not in a format this unit will play.
• The connected USB device is not supported by the product.
The Bluetooth device cannot be paired or connected with the unit.
• Ensure any other Bluetooth devices are turned off to avoid accidental pairing.
• You have not activated the Bluetooth function of your device; see page E19 or refer to
the Bluetooth device user’s manual.
• The system is not in pairing mode; press the VOCAL/PAIR button to restart pairing.
The Music is not available on the unit after successfully connecting the Bluetooth.
• Ensure your Bluetooth device can support the A2DP Bluetooth profile.
— E26 —
Updating the Firmware
Make sure the USB Flash Drive is securely plugged into the USB slot before running the
update. DO NOT interrupt the update. If interrupted during the update process, the
software can become corrupted and the unit will no longer function properly.
1. Create a folder on the USB Flash Drive named “user_update”.
2. Download the latest software (e.g xxxxxx.img) from www.singingmachine.com/
softwareupdates and save it into this folder.
3. Plug the USB Flash Drive into the USB jack on the unit and turn the unit on.
4. The unit will update automatically.
— E27 —
Specifications
AUDIO
Output Power (Tweeters) . ...................................................................5 Watts (RMS) 8 Ohms (2)
Output Power (Full range) ........................................................................ 30 Watts (RMS) 4 Ohms
BLUETOOTH
Bluetooth Version................................................................................................................................V4.2
Working Distance...........................................Up to 30 feet/10 meters measured in open space
Frequency bankd/Output.............................................................................. 2.402GHz - 2.480GHz
Power......................................................................................................................... ISM Band / < 5dBm
RECORDED FILE
MP3 Encoding...............................................................................................................................128kbps
USB
Format................................................................................................................................................. FAT32
Maximum Capacity............................................................................................................................32GB
JACK
Microphone.......................................................................................... 6.3 mm Microphone Jacks (2)
External Input.................................................................................................6.3 mm Microphone Jack
GENERAL
Power.................................................................................................. AC 100-240V, 50-60Hz, 1.5A
AC power (power adaptor)
Brand name . .......................................................................... GME Technology (Shenzhen) Co.,Ltd.
Model .................................................................................................................. GME72C-180300FUL
3A
Output ..................................................................................................................................... 18V
Battery (Lead Acid).................................................................................................................12V 5.0Ah
Dimensions - Main Unit..................... 22.2 (H) x 14.5 (W) x 13.8 (D) in (565 x 368 x 350 mm)
Weight - Main Unit.......................................................................................................20.7 lbs (9.4 kg)
Microphone........................ -74 dB 600 Ohms impedance with 6.3 mm Dynamic Microphone
Specifications are subject to change without notice.
The terms HDMI and HDMI High-Definition Multimedia
Interface, and the HDMI Logo are trademarks or registered
trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.
The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of
such marks by The Singing Machine Company, Inc. is under
license. Other trademarks and trade names are those of their
respective owners.
— E28 —
Visit Our Website: www.singingmachine.com
Singing Machine is distributed in the UK and Europe by:
Copyright © 2019 All Rights Reserved.
PDT Limited
Unit 4b, Greengate Industrial Estate, White Moss View,
Middleton, Manchester, M24 1UN, United Kingdom
[email protected]
PRINTED IN CHINA
9050-xxxx-ENG01-PDT
">