EverFocus | EBD934Q | Owner Manual | Everfocus EBD934Q Owner Manual

Everfocus EBD934Q Owner Manual
EBD934Q & ECZ934Q
eZ.HD Series 4-Megapixel True Day/Night IR Camera
User’s Manual
*EBD934QW White
ECZ934Q
EBD934Q Dark Gray
Copyright © EverFocus Electronics Corp.
Release Date: April, 2018
All the images including product pictures or screen shots in this document are for example only. The images
may vary depending on the product and software version. Information contained in this document is subject
to change without notice.
Precautions
1.
Do not install the camera near electric or magnetic fields. Install the camera away from
TV/radio transmitters, magnets, electric motors, transformers and audio speakers since the
electromagnetic fields generated from these devices may distort the video image or
otherwise interfere with camera operation.
2.
Never disassemble the camera beyond the recommendations in this manual nor introduce
materials other than those recommended herein. Improper disassembly or introduction of
corrosive materials may result in equipment failure or other damage.
3.
Try to avoid facing the camera toward the sun. In some circumstances, direct sunlight may
cause permanent damage to the sensor and/or internal circuits, as well as creating
unbalanced illumination beyond the capability of the camera to compensate.
4.
Keep the power cable away from water and other liquids and never touch the power cord
with wet hands. Touching a wet power cord with your hands or touching the power cord
with wet hands may result in electric shock.
5.
Never install the camera in areas exposed to oil, gas or solvents. Oil, gas or solvents may
result in equipment failure, electric shock or, in extreme cases, fire.
6.
Cleaning. For cameras with interchangeable lenses, do not touch the surface of the sensor
directly with the hands. Use lens tissue or a cotton tipped applicator and ethanol to clean
the sensor and the camera lens. Use a damp soft cloth to remove any dirt from the camera
body. Please do not use complex solvents, corrosive or abrasive agents for cleaning of any
part of the camera.
7.
Do not operate the camera beyond the specified temperature, humidity or power source
ratings. This camera is suitable for indoor operation only. Use the camera at temperatures
within -10°C~50°C (14°F~122°F) and humidity less than 80%; this device is not rated as
submersible. The input power source is 12VDC. Be sure to connect the proper + / - polarity
and voltage, as incorrect polarity or too high a voltage will likely cause the camera to fail,
and such damage is not covered by the warranty.
8.
Mounting. Use care in selecting a solid mounting surface which will support the weight of
the camera plus any wind, snow, ice or other loading, and securely attach the camera to the
mounting surface using screws and anchors which will properly support the camera. If
necessary (e.g. when mounting to drop ceilings) use a safety wire to provide additional
support for the camera.
2
Safety Notice
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
3
Contents
1.
Introduction...................................................................................................................... 5
1.1
1.2
Packing List ..................................................................................................................... 5
Features .......................................................................................................................... 5
2.
Cable Description .............................................................................................................. 6
3.
Installation ....................................................................................................................... 7
3.1
3.2
EBD934Q Installation and Adjustment ........................................................................... 7
ECZ934Q Installation and Adjustment.......................................................................... 11
5. Specifications .....................................................................................................................13
4
EBD934Q & ECZ934Q 4MP eZ.HD Camera
1.
Introduction
The EverFocus eZ.HD Series EBD934Q & ECZ934Q camera is equipped with a 4M pixels CMOS
sensor and providing high resolution of 4MP. Featured with the Digital Wide Dynamic Range
(D-WDR) function, the camera can provide clear images even under back light circumstances where
intensity of illumination can vary excessively.
Both of the cameras come with IR LEDs, supporting up to 15m (~50ft.) IR distance in night vision.
The camera can work in both indoor and outdoor environments. The IP66-rating and vandal proof
housing make it suitable for outdoor use. The cameras support both NTSC and PAL scanning
systems, which can be switched via OSD.
Note: The EBD934Q comes with two types: White (EBD934QW) and Dark Gray (EBD934Q).
1.1 Packing List
EBD934Q / EBD934QW
 Camera Body x 1
 User Manual x 1
 DC Power Pigtail Cable x 1
 Set Screw x 2




ECZ934Q
 Camera Body x 1
 User Manual x 1
 DC Power Pigtail Cable x 1
 Screw x 3



Mounting Screw x 4
Plastic Anchor x 4
Hexagon Wrench x 1
Template Plate x 1
Plastic Anchor x 3
Hexagon Wrench x1
Template Plate x1
1.2 Features

4-Megapixel with high flexibility and performance for astounding image

4M CMOS Sensor, delivering amazing high sensitivity

Astounding image quality from the 3.6mm lens

Extended IR range of up to 15m / 50ft. (depends on scene IR reflectivity)

D-WDR to improve the visibility under high contrast scene

The flexible angle viewing with its 3-Axis rotation design allows wall or ceiling mounting

Special design, easy installation and operation

eZ Controller function: Control camera OSD settings directly from DVR end
5
EBD934Q & ECZ934Q 4MP eZ.HD Camera
2.
Cable Description
No.
Name
Descriptions
1
Power Cable
Connect to a 12VDC power source.
2
Video Output
4MP and 960H output, using a 75 Ohm BNC-type coaxial cable.
3
DC Power Pigtail Cable
Optional power pigtail cable. The red wire is positive (+);
while the black wire is negative (-).
6
EBD934Q & ECZ934Q 4MP eZ.HD Camera
3.
Installation
3.1 EBD934Q / EBD934QW Installation and Adjustment
1.
For Ceiling Mount / Wall Mount users: Stick the Template Plate on the position where
you want to attach the camera.
2.
Drill four holes according to the supplied Template Plate, and insert the supplied Plastic
Anchors into the holes.
If you wish to run the wires through the wall / ceiling, drill an additional hole in the
middle of Template Plate.
7
EBD934Q & ECZ934Q 4MP eZ.HD Camera
3.
Unscrew the outer housing by twisting it counterclockwise and then remove the outer
housing from the camera base.
4.
Screw the base plate to the wall or ceiling with supplied four Screws and Hexagon
Wrench.
a. If you want to wire the cables from the side cut of the camera base, attach the camera
body to the base plate and run the cables through the camera base first, then screw
the camera base to the ceiling / wall.
8
EBD934Q & ECZ934Q 4MP eZ.HD Camera
b. If you want to wire the cables through the wall, attach and screw the camera base to
the ceiling / wall. Then attach the camera body to the base plate.
5.
Connect the camera to the 12VDC power source using the supplied DC Power Pigtail
Cable or power adapter.
9
EBD934Q & ECZ934Q 4MP eZ.HD Camera
6.
Screw back the outer housing and adjust the camera angle simultaneously.
7.
Screw the supplied two Set Screws using the Hexagon Wrench.
10
EBD934Q & ECZ934Q 4MP eZ.HD Camera
3.2
ECZ934Q Installation and Adjustment
1.
For Ceiling Mount / Wall Mount users: Stick the Template Plate on the position where
you want to attach the camera.
2.
Drill three holes according to the supplied Template Plate, and insert the supplied Plastic
Anchors into the holes.
11
EBD934Q & ECZ934Q 4MP eZ.HD Camera
3.
Connect the camera to an AHD DVR with the 12VDC power source using the supplied DC
Power Pigtail Cable or a power adapter.
4.
Adjust camera angles by tilting or rotating the camera. Then fasten the bracket with the
Hexagon Wrench (Note: The bracket base can be rotated by 360o , the housing body also
can be rotated by 360o and tilted by 90o).
5.
Configure camera settings by using the OSD Menu Joystick.
12
EBD934Q & ECZ934Q 4MP eZ.HD Camera
5. Specifications
Model
EBD934Q (Dark Gray)
Pickup Device
4M CMOS sensor
Video Format
NTSC / PAL (switchable via OSD)
Effective Pixels
2560(H) x 1440(V)
Scanning System
Progressive Scan
Sensitivity
0 Lux with IR On
Electronic Shutter
Auto / Manual (x30~1/50,000) / FLK
Gamma Correction
0.45
Lens Type
3.6mm fixed lens
FOV (D x H x V)
52.9° x 94.3° x 72.2°
BLC
OFF / BLC / HSBLC Selectable
AGC
0~15 Levels
White Balance
ATW / AWC-SET / Indoor / Outdoor / Manual
Sync. Mode
Internal
Day/Night
Ext, Auto, Color, B/W
UTC Function
Supported
IR LEDs
12 Units
IR Distance
Up to 15m / 50ft. (Depends on scene IR reflectivity)
S/N Ratio
>50dB
OSD Languages
English / Simplified Chinese / Traditional Chinese / German / French /
Italian / Spanish / Polish / Russian / Portuguese / Netherlands / Turkish
DNR
2DNR / Off
D-WDR
On / Off / Auto
Sens-up
Off / Auto (x2~x30)
Mirror
Off / Mirror / V-Flip / Rotate
Motion Detection
Off / On for 4 selectable zones
Privacy Mask
Off / On for 4 selectable zones
Environmental
IP66 Weather Resistant
Power Source
12VDC
Power Consumption
3W max.
Operating Temperature
-10°C ~ 50°C / 14°F ~ 122°F
Humidity
Less than 80%
Dimensions (Φ x H)
93 x 65mm / 3.66" x 2.56"
Weight
360g / 0.79lb
Certificates
CE, FCC, RoHS
Specifications and designs are subject to change without notice.
13
EBD934QW (White)
EBD934Q & ECZ934Q 4MP eZ.HD Camera
Model
ECZ934Q
Pickup Device
4M CMOS sensor
Video Format
NTSC / PAL (switchable via OSD)
Effective Pixels
2560(H) x 1440(V)
Scanning System
Progressive Scan
Sensitivity
0 Lux with IR On
Electronic Shutter
Auto / Manual (x30~1/50,000) / FLK
Gamma Correction
0.45
Lens Type
3.6mm fixed lens
FOV (D x H x V)
52.9° x 94.3° x 72.2°
BLC
OFF / BLC / HSBLC Selectable
AGC
0~15 Levels
White Balance
ATW / AWC-SET / Indoor / Outdoor / Manual
Sync. Mode
Internal
Day/Night
Ext, Auto, Color, B/W
UTC Function
Supported
IR LEDS
16 Units
IR Distance
Up to 15m/50ft. (depends on scene IR reflectivity)
S/N Ratio
>50dB
OSD Languages
English / Simplified Chinese / Traditional Chinese / German / French /
Italian / Spanish / Polish / Russian / Portuguese / Netherlands / Turkish
DNR
2DNR / Off
D-WDR
On / Off / Auto
Sens-up
Off / Auto (x2~x30)
Mirror
Off / Mirror / V-Flip / Rotate
Motion Detection
Off / On for 4 selectable zones
Privacy Mask
Off / On for 4 selectable zones
Environmental
IP66 Weather Resistant
Power Source
12VDC
Power Consumption
5W max.
Operating Temperature
-10°C ~ 50°C / 14°F ~ 122°F
Humidity
Less than 80%
Dimensions (Φ x H)
66 x 166.7mm / 2.6” x 6.56”
Weight
440g / 0.97lb
Certificates
CE, FCC, RoHS
Specifications and designs are subject to change without notice.
14
EBD934Q & ECZ934Q 4MP eZ.HD Camera
EverFocus Electronics Corp.
EverFocus Taiwan:
12F-1, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, New Taipei City, Taiwan
TEL: +886 2 2698 2334
FAX: +886 2 2698 3943
www.everfocus.com.tw
marketing@everfocus.com.tw
EverFocus Europe - Germany:
Albert-Einstein-Strasse 1, D-46446
Emmerich, Germany
TEL: +49 2822 93940
FAX: +49 2822 939495
www.everfocus.de
sales@everfocus.de
EverFocus China - Beijing:
Room 609, Technology Trade Building,
Shangdi Information Industry Base,
Haidian District, Beijing 100085, China
TEL: +86 10 6297 3336~39
FAX: +86 10 6297 1423
www.everfocus.com.cn
marketing@everfocus.com.cn
EverFocus China - Shenzhen:
3F,Building 7,Longcheng Industrial
Park,No.440,Longguan Road, Dalang Street, Longhua,
Shenzhen, Guangdong, China
TEL: +86 755 2765 1313
FAX: +86 755 2765 0337
www.everfocus.com.cn
marketing@everfocus.com.cn
EverFocus USA - California:
1801 Highland Avenue, Unit A, Duarte, CA 91010,
USA
TEL: +1 626 844 8888
FAX: +1 626 844 8838
www.everfocus.com
sales@everfocus.com
EverFocus Japan:
3F Kuramochi, Buildingll 2-2-3 Koto-Bashi,
Sumida-Ku Tokyo, 130-0022, Japan
TEL: +81 3 5625 8188
FAX: +81 3 5625 8189
www.everfocus.co.jp
info@everfocus.co.jp
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising