EverFocus | EZA2880 | Owner Manual | Everfocus EZA2880 Owner Manual

Everfocus EZA2880 Owner Manual
EZA2880 eZ.HD Series
8MP Dual Power IP66 IR Bullet Camera
User’s Manual
Copyright © EverFocus Electronics Corp.
Release Date: September, 2019
All the images including product pictures or screen shots in this document are for example
only. The images may vary depending on the product and software version. Information
contained in this document is subject to change without notice.
EverFocus Taiwan:
2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City 222, Taiwan
TEL: +886 2 2662 2338 FAX: +886 2 2662 3632 www.everfocus.com.tw
1.
Introduction
Equipped with a 8MP CMOS sensor, the EZA2880 deliver 8MP image quality.
The model provides motorized 3.6-11mm lens with ICR. Featured with True
Wide Dynamic Range (T-WDR), the camera can provide clear images even
under backlight circumstances where intensity of illumination can vary
excessively. The EZA2880 supports dual power (12VDC / 24VAC, depends on
model) and supports both NTSC and PAL scanning systems (auto detection).
1.1 Packing List



Camera x 1
Mounting Sticker x 1
L-Type Wrench x 1


Screw & Screw Anchor x 3
User Manual x 1
1.2 Features








8MP CMOS sensor, delivering amazing high sensitivity
Motorized 3.6-11mm lens with ICR to capture the desired field of view
Extended IR range of up to 40m / 131ft. with 4 LEDs (depends on scene
IR reflectivity)
T-WDR to improve the visibility under high contrast scene
3-Axis rotation design allows wall or ceiling mounting
IP66-rated with metal housing
Supports dual power (12VDC / 24VAC, depends on model)
Supports UTC function: Control camera OSD settings directly from DVR
end
1.3 Dimensions
91.5mm /3.6"
84mm / 3.31"
280mm / 11"
128mm / 5"
1
1.4 Optional Accessory
BAE3201
Color: White
Size (Φ x H): 138 x 54mm / 5.43” x 2.16”
Weight: 700g / 1.87
Material: Metal
1.5 Cable Description
12VDC or 24VAC Power Cable
Video Output Cable (BNC, 75Ohm)
2.
Installation
1. Stick the supplied Mounting Sticker to the surface to mark the 3 screw
positions. Drill 3 holes on the surface and insert the supplied 3 Screw
Anchors into the screw holes. If you want to run the cable through the
surface, drill a hole within the 3 screw area.
2. To mount the camera to the surface, screw the Camera Base to the surface
using the supplied 3 Screws.
Camera Base
Screws
Screw Anchors
Mounting
Surface
3. Connect the Power Cable to a 12VDC / 24VAC power source. Connect the
Video Output Cable to a monitor or DVR.
4. You can use the Joystick on the cable to configure camera OSD settings.
Remove the Protection Cap from the Joystick before using it.
2
UP
Configuring OSD Settings:
• Push the Joystick up / down to select among
menu items.
• Push the Joystick left / right to adjust the level
of the selected item.
• Press the Joystick to enter the submenu or
exit the OSD Setup Menu.
DN
5. You can optionally adjust camera angles. To do so, loosen the Tilt Screw or
Rotate Screw on the bracket using the supplied L-Type Wrench to adjust
camera angles. After adjusting camera angles, tightly screw back the
Tilt/Rotate screws.
Tilt Screw
Rotate Screw
3
3.
Configuration in the OSD Menu
No Main
1
2
Sub Menu
AF Mode
Motorized D&N Filter
Initial
Brightness
Exposure
Shutter
Sens-Up
AGC
HLC
BLC
3
Backlight
WDR
Off
Sub Menu / Function
One Shot, Manual
Sync On, Sync Off
On
0-20
Auto
Mode
Manual
Speed
Flicker
Not supported
0-10
Level
0-20
YEL, CYN, GRN, MAG, RED, BLU, BLK,
Color
WHT
H-POS
0-38
V-POS
0-35
H-SIZE
0-38
V-SIZE
0-35
WDR Mode Line
Window Zone 0-3
Window Use On, Off
H-POS
0-3856
Box
V-POS
0-2176
H-SIZE
0-3856
V-SIZE
0-2176
Window Zone 0-3
Window Use On, Off
ROI Mode
POS0-X
0-935
POS0-Y
0-361
POS1-X
0-935
Polygon
POS1-Y
0-361
POS2-X
0-935
POS2-Y
0-361
POS3-X
0-935
POS3-Y
0-361
Off
Weight
High, Middle, Low
Auto
4
Normal / Deblur
1/30, 1/60, 1/120, 1/250,
1/500, 1/1000, 1/2000,
1/4000, 1/8000, 1/15000,
1/30000
Day/Night Mode
Color
B/W
4
IR LED
Anti-Sat.
D>N Thres
N>D Thres
Delay
Adaptive, Off
0-20
0-20
0-20
High, Middle, Low
IR LED
Anti-Sat.
Adaptive, Off
0-20
Extern
5
6
7
Color
DNR
AWB
Auto
Autoext
Preset
Manual
D>N Thres
N>D Thres
Delay
IR LED
Anti-Sat.
Extern SW
D>N Thres
N>D Thres
Delay
0-20
0-20
High, Middle, Low
Adaptive, Off
0-20
High, Low
0-20
0-20
High, Middle, Low
C-Temp
R-Gain
B-Gain
3000K, 5000K, 8000K
0-20
0-20
Color Gain
0-20
High, Middle, Low, Off
Sharpness
0-10
Gamma
0.45, 0.55, 0.65, 0.75
Mirror
On, Off
Flip
On, Off
D-Zoom
Not supported
ACE
High, Middle, Low
Mode
On
Defog
Level
Off
On
Weight
Shading
Off
On
Box
Image
Off
Privacy
Polygon
On
5
Auto, Manual
High, Middle, Low
0%-100%
Zone Num
Zone Disp
H-POS
V-POS
H-Size
V-Size
Y Level
CB Level
CR Level
Trans
0-15
On, Off
0-120
0-68
0-80
0-61
0-20
0-20
0-20
0-3
Zone Num
Zone Disp
POS0-X
POS0-Y
POS1-X
POS1-Y
POS2-X
POS2-Y
POS3-X
POS3-Y
Y Level
CB Level
0-7
On, Off
0-240
0-136
0-240
0-136
0-240
0-136
0-240
0-136
0-20
0-20
CR Level
Trans
Det Window
8
Motion
On
Off
Output
9
System
Image Range
Color Space
Audio Mic
Color Bar
Language
Cam Title
10 Exit
Reset
Sensitivity
Motion OSD
Text Alarm
Signal Out
Off
Window Use
Window Zone
Det H-POS
Det V-POS
Det H-Size
Det V-Size
0-10
On, Off
On, Off
On, Off
0-20
0-3
0-3
On, Off
0-96
0-56
0-96
0-56
Frame Rate
4K/15fps, 4MP/30fps, 1080p/30fps
Freq
60Hz (Auto Detection)
SDI Mode
Not supported
SDI UCC Stop Not supported
Analog Mode AHD, TVI, CVI, CVBS
Confirm
Yes
Return
Full
Comp
User
Offset
0-32
HD-CbCr, SD-CbCr, YUV
Not supported
On, Off
ENG, CHN, CHN(S), JPN, KOR, POR, ESP
Left-Down
Right-Up
Off
On
6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising