EverFocus | VANGUARD 8x4H | Owner Manual | Everfocus VANGUARD 8x4H Owner Manual

Everfocus VANGUARD 8x4H Owner Manual
VANGUARD 4x2H / 8x4H / 16x8H
4CH / 8CH / 16CH H.265 4K Hybrid DVR
Quick Installation Guide
VANGUARD 16x8H
VANGUARD 8x4H
VANGUARD 4x2H
Copyright © EverFocus Electronics Corp.
Release Date: February 2019
All the images including product pictures or screen shots in this document are for example only. The images may
vary depending on the product and software version. Information contained in this document is subject to
change without notice.
EverFocus Taiwan:
2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City 222, Taiwan
TEL: +886 2 2662 2338 FAX: +886 2 2662 3632 www.everfocus.com.tw marketing@everfocus.com.tw
1. Overview
1.1 Front Panel
VANGUARD 16x8H / VANGUARD 8x4H / VANGUARD 4x2H
PWR
2
1
No.
1
Name
IR Receiver
2
LED Indicator
3
USB2.0 Port
HDD
3
Description
Receiver for signals from the IR remote control.
Power: When power is on, the LED will continue lighting in green.
HDD: When power is on, the LED will continue lighting in red. When HDD is
reading/writing data, the LED will flashes red.
USB2.0 port for connecting to a mouse or an external storage device.
1.2 Rear Panel
VANGUARD 16x8H
e-SATA
12
3
2
1
4
VANGUARD 8x4H
5
6
7
4
8
9
10 11
5
e-SATA
3
12
1
VANGUARD 4x2H
2
6
7
12
e-SATA
2
3
1
6
4
1
8
5
9
10
7
8
9
10
11
No.
Name
Description
1
Audio Input
Connects to audio input devices, such as microphones. Note that the microphones
with a (built-in) amplifier and external power supply are required.
2
Audio Output
Connects to an audio output device, such as speakers. Note that the speakers with a
(built-in) amplifier and external power supply are required.
3
Video Input
Connects the AHD/TVI/SD cameras to the Video Input.
4
VGA Port
5
Terminal Block
Connects to a monitor using a VGA cable.
The Terminal Block provides alarm inputs, alarm output and RS-485 connection (see
3.1 Terminal Block).
6
HDMI Port
Connects to a monitor using a HDMI cable.
7
8
9
10
11
LAN
USB2.0 Port
Power Port
Power Switch
IR Receiver Port
Connects to the Network.
The USB2.0 port for connecting to a mouse or external storage device.
Connects to a 12VDC power source.
Press to turn on or off the power.
You can optionally connect an external IR Remote Control Receiver to this port.
12
e-SATA
Connects to an external e-SATA storage device.
1.3 Packing List
•
•
•
•
DVR x 1
Power Cord + Adaptor x 1
Mouse x 1
HDD Screw x 8
•
•
•
•
Audio Cable (CH5-16) x 1 (only for VANGUARD 16x8H)
Quick Installation Guide x 1
CD x 1 (see Note 3)
IR Remote Control (with 2 AAA batteries) x 1 (see Note 4)
Note:
1. Equipment configurations and supplied accessories vary by country. Please consult your local EverFocus
office or agents for more information. Please also keep the shipping carton for possible future use.
2. Contact the shipper if any items appear to have been damaged in the shipping process.
3. The CD contains the IP Utility software, User Manual and Quick Installation Guide.
4. Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the
instructions.
a. Use only two AAA dry cell batteries.
b. Do not dispose of the batteries in a fire as it may explode.
1.4 Dimensions
2
2. Basic Installation
2.1 Hard Disk Installation
You can install two 3.5” HDDs inside the DVR for recording videos. The maximum capacity of each HDD is 8TB.
1. Make sure the DVR is power-off.
2. Unscrew the eight housing screws (4 on the rear panel, 2 on the left and right side each). To remove the
housing cover from the DVR, push the cover backward and then lift it.
3. Find the SATA cable inside the DVR, and connect the SATA cable to the SATA port on the HDD (left image).
Find the internal power cable, and connect the internal power cable to the HDD (right image).
4. Place the HDDs inside the DVR, screw the HDDs from the bottom side of the DVR using the supplied Screws.
5. Screw the housing cover back to the DVR.
3
2.2 Hard Disk Compatibility List
Please go to the product page (Download) on EverFocus’ Website www.everfocus.com.tw to see the latest
Storage Compatibility List. It’s recommended to use the hard disk models listed on the Storage Compatibility List
to ensure your hard disks are compatible.
Note: If using two or more hard disks, please choose the hard disks with the same capacity.
3. Basic Connection
The instructions below describe the basic connection to the DVR.
The image below uses VANGUARD 16x8H as example.
3.5" HDD
1
TVI/AHD/SD Camera
2
Main Monitor
(VGA)
3
e-SATA
4
5
3
6
7
Network
Line Level
Audio Input
Line Level
Audio Out
Main Monitor
(HDMI)
IP Cameras
Web Remote Client
VANGUARD CMS
8
Power Supply
Mouse / USB Storage
1. To record videos, install 3.5” HDD(s) to the DVR. Please refer to 2.1 Hard Disk Installation.
2. To connect to the TVI/AHD/SD cameras, connect the cameras to the BNC ports.
3. To view videos at local site, connect a monitor to the HDMI or VGA port using the HDMI or VGA cable
supplied by the monitor manufacturer.
4. Connect microphones to the audio input ports to transmit audio from the camera to the DVR. Note that the
microphones with a (built-in) amplifier and external power supply are required.
5. To listen to the audio from device side, connect speakers to the audio output. Note that the speakers with a
(built-in) amplifier and external power supply are required.
6. Use a standard RJ-45 CAT5 Ethernet cable to connect the DVR to the network and then optionally connect IP
cameras to the DVR.
7. Optionally connect a mouse to the DVR to control the system. You can also control the system using the
supplied IR Remote Control.
8. Use the supplied Power Cord and Adaptor to connect the DVR to the power outlet.
4
3.1 Terminal Block
VANGUARD 16x8H
Alarm Input: 16
Alarm Output: 1
RS-485: 1
VANGUARD 4x2H
VANGUARD 8x4H
Alarm Input: 4
Alarm Output: 1
RS-485: 1
Alarm Input: 8
Alarm Output: 1
RS-485: 1
4. Turning On / Off the Power
Before powering on the DVR, please make sure the internal HDD have been installed properly. Once you have
completed the basic cable connections, you are ready to turn on the DVR. Simply plug in the power source and
then press the Power Switch on the rear panel of the DVR. The POWER LED will light up if power is normal and
the DVR will enter the System Initialization process.
When the process is done, it’s required to set up a password for the administrator account immediately in
order to protect your privacy.
To turn off the power, click the Shutdown button on the Exit page (OSD menu > Exit > Shutdown) and then
press the Power Switch on the rear panel of the DVR.
5
5. P2P Function
The P2P function allows users to add DVRs to the VANGUARD App through QR code.
1.
Install EverFocus VANGUARD App. For Android users, go to Google Play Store. For iOS users, go to Apple
Store. After the installation process is complete, start EverFocus VANGUARD App.
2.
To add a DVR through P2P, tap Menu > Device List, and then tap the “+” button on the upper-right corner.
3.
Scan the DVR’s QR code on the System Info page of the DVR OSD menu. Input the DVR ID, password and
Media Port 8000. Tap the Save button.
……
6
4.
The DVR is now added and connected to the App. You can start accessing the DVR.
P/N: 4605VAN0402002A
7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising