EverFocus | EAN3300 | Owner Manual | Everfocus EAN3300 Owner Manual

Everfocus EAN3300 Owner Manual
EAN Series IP Box Camera
Full HD, WDR, DNR, True Day/Night
User’s Manual
* Lens not included.
Copyright © EverFocus Electronics Corp,
Release Date: December, 2013
Copyright  2013 EverFocus Electronics Corp.
All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form or by
any means without written permission of the EverFocus Electronics Corporation.
EverFocus
12F, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, Taipei, Taiwan
TEL: +886 2 2698 2334
FAX: +886 2 2698 2380
www.everfocus.com.tw
December, 2013
About this document
All the safety and operating instructions should be read and followed before the unit is operated. This
manual should be retained for future reference. The information in this manual was current when
published. The manufacturer reserves the right to revise and improve its products. All specifications are
therefore subject to change without notice.
Regulatory Notices
FCC Notice "Declaration of Conformity Information"
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications made to this equipment, not expressly approved by EverFocus or
parties authorized by EverFocus could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
EverFocus Electronics Corp.
12F, No. 79, Sec. 1, Shin-Tai Wu Rd., Hsi-Chi,
Taipei Hsien, Taiwan, R.O.C.
EAN series cameras comply with CE and FCC.
Precautions
1. Do not install the camera near electric or magnetic fields.
Install the camera away from TV/radio transmitters, magnets, electric motors, transformers and
audio speakers since the electromagnetic fields generated from these devices may distort the video
image or otherwise interfere with camera operation.
2. Never disassemble the camera beyond the recommendations in this manual nor introduce
materials other than those recommended herein.
Improper disassembly or introduction of corrosive materials may result in equipment failure or other
damage.
3. Try to avoid facing the camera toward the sun.
In some circumstances, direct sunlight may cause permanent damage to the sensor and/or internal
circuits, as well as creating unbalanced illumination beyond the capability of the camera to
compensate.
4. Keep the power cord away from water and other liquids and never touch the power cord with wet
hands.
Touching a wet power cord with your hands or touching the power cord with wet hands may result
in electric shock.
5. Never install the camera in areas exposed to oil, gas or solvents.
Oil, gas or solvents may result in equipment failure, electric shock or, in extreme cases, fire.
6. Cleaning
For cameras with interchangeable lenses, do not touch the surface of the sensor directly with the
hands. Use lens tissue or a cotton tipped applicator and ethanol to clean the sensor and the camera
lens. Use a damp soft cloth to remove any dirt from the camera body. Please do not use complex
solvents, corrosive or abrasive agents for cleaning of any part of the camera.
7. Do not operate the camera beyond the specified temperature, humidity or power source ratings.
Use the camera at temperatures within 0°C ~ 50°C / 32°F ~ 122°F (12 VDC); this device is not rated as
submersible. The input power source is 12 VDC / PoE. Be sure to connect the proper + / - polarity
and voltage, as incorrect polarity or too high a voltage will likely cause the camera to fail, and such
damage is not covered by the warranty. The use of properly fused or Class 2 power limited type
supplies is highly recommended.
8. Mounting
Use care in selecting a solid mounting surface which will support the weight of the camera plus any
wind, snow, ice or other loading, and securely attach the camera to the mounting surface using
screws and anchors which will properly support the camera. If necessary (e.g. when mounting to
drop ceilings) use a safety wire to provide additional support for the camera.
ii
CONTENTS
1. Introduction ..................................................................................................................................... 1
2. Physical Description ......................................................................................................................... 2
3. Features ........................................................................................................................................... 3
4. Installation ....................................................................................................................................... 4
4.1
Packing List ....................................................................................................................................... 4
4.2
I/O Terminal Block ........................................................................................................................... 5
4.3
Lens Installation and Adjustment .................................................................................................... 5
4.4
Top / Bottom-Mount ....................................................................................................................... 6
4.5
Basic Connection .............................................................................................................................. 7
5. Accessing the User Interface ............................................................................................................. 8
5.1
Checking the Dynamic IP Address.................................................................................................... 8
5.2
Settings for Microsoft Internet Explorer........................................................................................ 10
5.3
Connecting the Camera to the Network........................................................................................ 12
5.4
Live View Window.......................................................................................................................... 14
6. Playback......................................................................................................................................... 17
6.1
Playback Window ........................................................................................................................... 17
6.2
Setting up the Playback Function .................................................................................................. 19
6.3
7
6.2.1
Preparing the Micro SD Card ......................................................................................... 19
6.2.2
Testing the Playback Function ....................................................................................... 19
Playing Back Using ARV Viewer ..................................................................................................... 21
Settings .......................................................................................................................................... 22
7.1
7.2
7.3
System Info .................................................................................................................................... 22
7.1.1
Information .......................................................................................................................................... 22
7.1.2
Log .......................................................................................................................................................... 23
User Config ..................................................................................................................................... 24
7.2.1
Live View Config ................................................................................................................................. 24
7.2.2
Recording / Snapshot ........................................................................................................................ 25
7.2.3
Language ............................................................................................................................................... 26
Network ......................................................................................................................................... 27
iii
7.4
7.3.1
Network ................................................................................................................................................ 27
7.3.2
DDNS ...................................................................................................................................................... 29
7.3.3
SMTP / FTP ........................................................................................................................................... 31
7.3.4
HTTPS ..................................................................................................................................................... 33
7.3.5
SNMP ..................................................................................................................................................... 36
7.3.6
Network Alarm .................................................................................................................................... 36
Video .............................................................................................................................................. 37
7.4.1
Multi Streaming .................................................................................................................................. 37
7.4.2
Camera .................................................................................................................................................. 39
7.4.3
Advanced .............................................................................................................................................. 42
7.4.4
ROI (Region of Interest).................................................................................................................... 54
7.4.5
Privacy Mask ........................................................................................................................................ 55
7.4.6
Schedule................................................................................................................................................ 56
7.5
Audio .............................................................................................................................................. 57
7.6
User ................................................................................................................................................ 58
7.7
7.8
7.6.1
User Information ................................................................................................................................ 58
7.6.2
IP Address Filter .................................................................................................................................. 60
Event .............................................................................................................................................. 61
7.7.1
Event Settings...................................................................................................................................... 61
7.7.2
Motion Detection ............................................................................................................................... 64
7.7.3
Tamper Detection .............................................................................................................................. 65
7.7.4
Alarm I/O .............................................................................................................................................. 65
7.7.5
Schedule................................................................................................................................................ 66
System ............................................................................................................................................ 67
7.8.1
Date/Time............................................................................................................................................. 67
7.8.2
Daylight Saving.................................................................................................................................... 68
7.8.3
SD Card .................................................................................................................................................. 68
7.8.4
Maintenance........................................................................................................................................ 70
8. Upgrading Firmware Using IP Utility ............................................................................................... 72
9. Specifications ................................................................................................................................. 74
10. Troubleshooting ............................................................................................................................ 76
iv
EAN3120/3220/3300
1. Introduction
The EAN series is a box-type IP camera delivering image quality of up to 3-megapixel. The EAN series
features the Wide Dynamic Range (WDR) function, which can provide clear images even under back light
circumstances where intensity of illumination can vary excessively. A built-in micro SD card slot and
Power over Ethernet (IEEE802.3af Class 3) features are also provided. You can power the camera over
the network or by connecting the camera to a 12 VDC power supply. The camera also features H.264 /
MJPEG multi-stream output for simultaneous live monitoring and high-resolution recording. Since the
EAN series conforms to ONVIF / PSIA for compatibility with other network video devices, it interoperates
with a wide variety of hardware and software systems. You can also use EverFocus Mobile Applications
to remotely view the live views of the cameras through your handheld devices; or use EverFocus CMS to
remotely manage multiple IP devices connected on the LAN or WAN. The EAN series is designed for
simple installation and supports all types of indoor mounting applications.
The EAN Series Models
Model Name
EAN3120
EAN3220
EAN3300
Megapixel
1.3 MP
2 MP
3 MP
WDR
Yes
Yes
No
System Requirements
Before installing, please check that your computer meets the following system requirements.
Operating System
Microsoft Windows XP / Vista (32-bit) / 7 (32-bit)
CPU
Intel Core2 Duo 2 GHz or higher
RAM
1 GB or more
Additional HD space depends on required local storage of video files,
100 Mbps network card.
Screen Resolution
1024 x 768 pixels or higher, 32-bit pixel color resolution
Software
DirectX 9.0c
Microsoft Internet Explorer 7 or higher
Note: For using the Internet Explorer, some settings are required. Please refer to 5.2 Settings for
Microsoft Internet Explorer.
1
EAN3120/3220/3300
2. Physical Description
1
2
3
No.
1
2
3
4
5
6
Item Name
Memory Card Slot
Power LED
12 VDC Port
Ethernet / PoE
Reset Button
I/O Terminal Block
7
Video Test-Out
4
5
6
7
9
8
10
11
Descriptions
Insert a micro SD / SDHC card to store recording data.
Indicates the power is supplied.
Connects to power.
Connects to a 10/100 Ethernet or PoE.
Resets all configurations to factory default.
Connects I/O devices.
Connects to a portable monitor for testing the camera view and
setting the focus and angle of the camera during initial
installation.
8
Audio In
Connects to a microphone. Note that the audio input features a
line-in 3.5mm jack (TRS). Be sure to prepare microphones with TRS
connector (see TRS Connector image below). Also, microphones
with a (built-in) amplifier and external power supply are required.
9
10
Audio Out
Light Sensor
Connects to a speaker for audio output.
Detects lights.
11
Auto Iris Lens Connector
Plug the Iris control cable to the connector.
TRS Connector
To activate the Audio function, the Enable Audio must be checked.
See 7.5 Audio.
Ground (Sleeve)
Right Channel (Ring)
Left Channel (Tip)
2
EAN3120/3220/3300
Dimensions
3. Features
•
1/3” Panasonic CMOS sensor (for EAN3120 / 3220)
1/2.8” Sony CMOS sensor (for EAN3300)
•
•
Triple streams (stream 1 / 2 / 3 from H.264 or MJPEG)
Up to 30 fps at 1920 × 1080
Supports 15 fps at 2048 × 1536 (only for EAN3300)
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Auto Iris control
Built-in micro SD / SDHC card slot
Removable IR-cut filter for Day / Night function
One alarm input and output
Two-way audio
TV-out
Wide Dynamic Range (for EAN3120 / 3220)
2D / 3D Dynamic Noise Reduction (DNR)
Motion detection
Privacy mask
12 VDC / PoE
Multi-languages on Web interface
ONVIF / PSIA compliant
Supports EverFocus CMS and Mobile Applications
3
EAN3120/3220/3300
4. Installation
4.1
•
•
•
•
Packing List
EAN Series Camera (lens not included) x 1
Software CD x 1
Quick Installation Guide x 1
Tool Packet x 1 (contains the following items)
- C-mount lens adapter
- ¼-20 UNC thread mounting bracket and 2 screws
- Hexagon wrench
-
Power pigtail cable
Note:
1. Equipment configurations and supplied accessories vary by country. Please consult your local
EverFocus office or agents for more information. Please also keep the shipping carton for
possible future use.
2. Contact the shipper if any items appear to have been damaged in the shipping process.
4
EAN3120/3220/3300
4.2
I/O Terminal Block
The I/O terminal block, located on the rear panel of the camera, can be used to develop application
for alarm input and output.
1 2 3 4
4.3
Pin Assignment
No. Function
No. Function
1
Alarm COM (-)
3
Alarm Input (+)
2
Alarm Output (+)
4
Digital GND (-)
Lens Installation and Adjustment
You can install either a CS-mount or a C-mount lens into the camera. It is recommended to use a lens
with aperture ratio of F/1.4 or smaller. Please refer to the following reference steps.
Focus Screw
Zoom Screw
C-Mount Lens Adapter
DC Auto Iris Lens Connector
CS-Mount Lens:
1. Remove the cover cap from the camera body.
2. Install the lens into the camera body.
3. Adjust the lens using the Focus / Zoom Screws.
If you are using a DC Auto Iris lens:
1. Remove the cover cap from the camera body.
2. Install the lens into the camera body.
3. Connect the DC cable to the DC Auto Iris Lens Connector.
5
EAN3120/3220/3300
4.
When making final focus adjustment, place the ND filter in front of the lens to force the lens iris
to open, and then adjust the lens using the Focus / Zoom Screws.
Note: To use the ND filter, remove the protective sheets from both sides of an ND filter.
5. Lock the Focus Screw and then remove the ND filter.
C-Mount Lens:
1. Remove the cover cap from the camera body.
2. Install the lens into the camera body using the supplied C-mount lens adapter.
3. Adjust the lens using the Focus / Zoom Screws.
Note: Installing a C-mount lens without the C-mount lens adapter may damage the camera sensor.
4.4
Top / Bottom-Mount
You can use the supplied mounting bracket and screw it on the top of the camera body to suspend
the camera, or on the bottom of the camera body to support the camera.
Top Mount
Bottom Mount
Note: Before mounting the EAN3300, please access the Web interface first to calibrate the iris.
Please refer to 7.4.2 Camera in the User’s Manual.
6
EAN3120/3220/3300
4.5
Basic Connection
3
Audio
1
Ethernet
(PoE)
Power DC 12V
Micro SD
3
Out
Video Out
4
GND
Reset
COM
Out
In
2
In
Alarm
5
1.
Use a standard network cable to connect the camera to the network.
2.
Connect the camera to power using one of the following methods:
•
Plugging the supplied power pigtail cable to the 12 VDC port.
•
Using the PoE function and the power will be provided over the network cable.
3.
Optionally connect the camera to a speaker or microphone. Note that the audio input features a
line-in 3.5mm jack (TRS). Be sure to prepare microphones with TRS connector. Also, microphones
with a (built-in) amplifier and external power supply are required.
4.
Optionally connect the camera to a monitor using a video Test-Out cable.
5.
Optionally connect the camera to the input / output devices.
After powering the camera, the power LED will be lit in red and you can access the live view and
adjust the image clarity.
7
EAN3120/3220/3300
5. Accessing the User Interface
This section explains how to access the Web interface of the camera for configuration.
5.1
Checking the Dynamic IP Address
You can look up the IP address and access the Web interface of the camera using the IP Utility (IPU)
software included in the software CD. Please connect the IP camera in the same LAN of your computer.
1.
Install and then start the IPU program
. The following IPU window appears. The IPU will
automatically search the IP devices connected in the LAN.
2.
To access to the Live View window, double click the IP address of the desired device, the login
window pops up. Type the user ID and password to log in. By default, the user ID is user1 and the
password is 11111111.
3.
Click OK, the Live View window appears.
Note:
1. You might be required to download ActiveX for viewing the camera feed. If asked, click Yes.
2. To enable Remote Live View, Firmware Upgrade and ActiveX Prompt on Internet Explorer,
some settings have to be complete. Please refer to 5.2 Settings for Microsoft Internet
Explorer in the User’s Manual.
8
EAN3120/3220/3300
4.
To optionally configure the Machine Name, IP Address, IP Type or Port Number using the IPU:
a.
Log in the camera by checking the desired model and then click the Log in
in dialog box appears.
icon. The Log
b.
Type the Username and Password. Click the OK button, the Login status displays.
Note:
1. The default user ID is user1 and the default password is 11111111.
2. If you select more than one camera that has the same user ID / password, you will be
able to log in several cameras at once.
c.
Right click the column to configure the settings. Click the Apply Changes
button to
apply and save the settings.
Note: Most networks uses DHCP to assign IP address, if you are unsure of your network
settings, please consult your network administrators for configuration details.
9
EAN3120/3220/3300
5.2
Settings for Microsoft Internet Explorer
To enable Remote Live View, Firmware Upgrade and ActiveX Prompt on Internet Explorer, some
settings have to be complete. Please follow the steps below:
1.
On the computer, click Start > Control Panel > System and Security > Action Center (click Change
User Account Control Settings), the User Account Control Settings window appears. Adjust the
slide bar to Never Notify and then click OK. Restart your computer if requested.
2.
Open the Internet Explore, click Tools > Internet Options > Security Tab > Custom Level, the
Security Settings windows appears.
10
EAN3120/3220/3300
3.
In the Download unsigned ActiveX controls field, select Prompt. In the Include local directory
path when uploading files to a server field, select Enable. Click OK.
4.
In the Internet Options window, click the Advanced tab and then disable Enable memory
protection to help mitigate online attacks. Click OK.
11
EAN3120/3220/3300
5.3
Connecting the Camera to the Network
There are three methods to connect the IP camera to the network: Router or LAN Connection, Direct
High-Speed Connection and One-to-One Connection.
Router or LAN connection
This is the most common connection in which the IP camera is connected to a router and allows
multiple users on and off site to see the IP camera on a LAN/WAN (Internet). The camera must be
assigned an IP address that is compatible with its LAN. By setting up port forwarding on the router,
you can remotely access the cameras from outside of the LAN via the Internet. To remotely access the
Web interface of the IP camera, please refer to 7.3.2 DDNS. To set up port forwarding, please consult
the manual of the router.
Cat 5 Straight Through Cable
Internet
High-speed modem
Straight-through LAN patch cable
Router
Left: Pinout of a straight-through cable.
12
EAN3120/3220/3300
Direct High-Speed Connection
In a Direct High-Speed Connection, the camera connects directly to a modem without the need for a
router. You need to set the static or dynamic WAN IP address assigned by your ISP (Internet Service
Provider) in the camera’s configuration web pages. To access the camera, just type “http://xxx”,
where xxx is the IP address given by your ISP. If you have a dynamic IP address, this connection may
require that you use DDNS for a reliable connection. Please refer to 7.3.2 DDNS.
Internet
Cat 5
Straight Through Cable
High-speed modem
One-to-One Connection (Directly from PC to IP Camera)
You can connect directly without using a switch, router or modem. However, only the PC connected
to the camera will be able to view the IP camera. You will also have to manually assign a compatible IP
address to both the computer and the IP camera. Unless the PC has another network connection, the
IP camera will be the only network device visible to the PC. See the diagram below:
Cat 5
Right: Pinout of a crossed-over cable.
13
EAN3120/3220/3300
5.4
Live View Window
1. Click the
button to display the "Live View" window. Double-click on the image
to show a full-screen display, double-click again or press ESC to return to the normal display. If you
experience video feed lag time (if connected via Internet), you can reduce the resolution or limit
the number of streams. See 7.4.1 Multi Streaming.
2. Click the
button to play the recorded data directly from the on-camera Micro
SD / SDHC card (for this function to become active, you have to insert a Micro SD / SDHC card in the
Micro SD / SDHC card slot on the rear panel of the camera. See 7.8.3 SD Card.
3. Click the
button to enter the Settings page, which includes 8 submenus:
[System Info], [User Config], [Network], [Video], [Audio], [User], [Event], and [System]. Please refer
to 7. Settings for more details.
Click the
button to exit the system and close this browser page.
14
EAN3120/3220/3300
4. Video Stream
Select the Video Stream (Stream 1, Stream 2 or Stream 3) that will be displayed in the live view
window on the right. Stream 2 and Stream 3 are only selectable if you have enabled the stream
(see 7.4.1 Multi Streaming). The default setting is Stream 1 only.
5. View Size
Use this to select the appropriate view size and shape of the live view window on the right. A
smaller size might increase transmission speed and video quality.
6. Digital Zoom
Click the Zoom In / Zoom Out buttons or roll the mouse wheel to zoom in / out the camera live view
up to 10x. Click the Home button to go back to the home position.
Marquee Mode: Select this mode to drag around a portion of the live view window you want to
zoom into with your mouse.
Normal Mode: Select this mode to set the zoom level in the magnified window. Clicking on the
magnified image will re-center the image around that point.
7. Record
Click the Record button to start / stop recording the current video stream. By default, this icon is
only for one-minute video recording and the recordings will be saved at C:\EverFocus\. To change
the recording time, see File Size in 7.2.2 Recording/Snapshot. To change the location, see Export
Folder in 7.2.2 Recording/Snapshot. To record long-period recordings, please set up a recording
schedule (7.7.5 Schedule). To change the source video stream and recording format, see Video
Recording Settings in 7.4.1 Multi Streaming.
Note: For Microsoft IE10 and above users, some settings have to be complete to enable this
function (see B. Snapshot/Record error message in 10. Troubleshooting).
8. Snapshot
Click the Snapshot button to save a snapshot of the video image currently being displayed. By
default, the snapshot will be saved at C:\EverFocus\. To change the location, see 7.2.2
Recording/Snapshot.
Note: For Microsoft IE10 and above users, some settings have to be complete to enable this
function (see B. Snapshot/Record error message in 10. Troubleshooting).
9. Speaker / Microphone
Click the Speaker and Microphone buttons to switch the sound on/off for the speakers and
microphones respectively (if such external devices have been connected to the camera directly or
via the network). To activate the Audio function, the Enable Audio must be selected. See 7.5 Audio.
Note that the camera provides a line-in 3.5mm jack (TRS), therefore, TRS microphones with a
(built-in) amplifier and external power supply are required.
15
EAN3120/3220/3300
10. One Push
This function is only available for EAN3120 / 3220. The One Push button can be displayed on the
live view window by enabling the Show One Push Buttons function on the User Config < Live View
Config Setting page (see 7.2.1 Live View Config). To enable the button (turned from faded to clear),
on the Video < Advanced Setting page, select One Push from the White Balance Settings Mode
drop-down list, and click the Apply button. Once this is done, clicking the One Push button on the
Live View Window will instruct the camera to adjust the white balance settings, and these settings
will be active until the button is clicked again. This is like a “semi-automatic” way to adjust white
balance to suit the user, if the Auto or Manual mode does not give the result the user wants.
11. Manual Control
–
Trigger Event
Click the “Trigger Event” button to trigger an event directly from the Live page. If you have
configured an event (in the Event submenu) that will trigger a reaction (like a recording) when a
Manual Trigger event occurs, clicking this button will trigger that reaction. You can select what that
reaction will be. You can, for instance, set the camera to record the audio/video feed to the Micro
SD card on board the camera. You can then click on the Playback button to open the Playback page
and search for and play all such recordings that had been stored on the card. Such event actions
will be effective once they have been configured in the “Event” menu (see 7.7 Event).
–
Reset Alarm
Click the “Reset Alarm” button to reset the alarm output remotely.
12. Status Display (info lines that can be placed above video box or at bottom of page)
This shows the name of the camera that is currently active or being configured, current date/time
and current frame rate. You can activate these info displays in the Settings > User Config page (see
7.2.1 Live View Config).
13. Event Signal Icons (above video screen)
When an alarm or motion event is triggered, a signal icon will appear at the top right of the Live
View window to alert the user.
Alarm event icon
: When an alarm is triggered, this icon appears.
Motion detection icons
: The colors of these motion event icons correspond to the
colors of the motion trigger areas you have configured in the Motion Detection submenu (see 7.7.2
Motion Detection).
Recording icon
: When the camera is recording to a PC-based folder, this icon appears.
16
EAN3120/3220/3300
6. Playback
You can remotely play back the recordings stored in the on-camera micro SD card on the Web interface,
or play back the recordings stored in the computer using the ARV Viewer included in the software CD.
Playback is designed as a quick way to check recent recordings that were triggered by Events that were
configured to “Record to SD Card” in the Settings > Event > Event Settings page (see 7.7.1 Event
Settings).
Note: Note that the Playback page is only accessible once the on-camera SD card is inserted and
active.
6.1
Playback Window
On the Live View Window, click the Playback button
17
to open the Playback page.
EAN3120/3220/3300
Search by File: Click the Search button to search for all recording files on the on-camera SD card.
Search results will be displayed in the Filename area.
Search by Time: Click the calendar icon and select the date and time from which you want to search
until the present moment. Click search to get your search results, which will be displayed in the
Filename area.
Search by event: Click the type of Event recordings you want to search for (Alarm, Motion, Manual
Trigger) and then click the calendar icons to select the Start Time date/time and the End Time
date/time of your search. Click Search to get your search results, which will be displayed in the
Filename area.
Multiple Files: Check this box if you want the video player to play all the files in the selected folder.
The files will be displayed in the Filename area.
Loop Again: Check this box if you want the video player to play the selected file over and over again.
Play: Once you have opened the file’s folder and have clicked on the file to highlight it, its details will
be displayed in the File Information area. You can now click Play to play that specific file.
Pause: Click this button to pause the playback.
Stop: Click this button to stop the playback.
【Recording List】
Filename: This area will display a list of search results (recording files and folders). Folders (named
with the recorded date) will be displayed first. Click on the folder and click on each subfolder until the
recording files (.arv) in that folder is listed.
File Information: Click a file on the Filename list, the selected file information will be listed.
Copy: Click this button to copy the selected file to the computer-based folder of your choice. A
browsing box will open so that you can search for the folder of your choice. You can use the ARV
Viewer to play back the recordings recorded in your computer. For details on ARV Viewer, see 6.3
Playing Back Using ARV Viewer.
Lock: Click this button to lock the selected file. This will protect that file from being overwritten during
any overwrite procedure. The file will thus be saved on the micro SD card indefinitely. However, the
file will still be deleted if the micro SD card is ever formatted.
Remove: Click this button to delete the selected file.
18
EAN3120/3220/3300
6.2
Setting up the Playback Function
Note that the Playback function will not be active until the user has inserted a micro SD card in the
camera’s micro SD card slot. The card may also have to be formatted in the Settings submenu.
Micro SD Card Slot
6.2.1
Preparing the Micro SD Card
Once you insert a functional micro SD card into the slot, the Playback button on the Live page should
become active within seconds (see section 6.2.2 below – the grey letters should turn white). IF NOT,
do the following:
1. From the Live page, click Settings > System > SD Card. If no card has been inserted yet, the
Remove button should be faded, indicating that no card is being detected. (If a card is
inserted, and the Remove button is still faded, pull the card out and re-insert it.)
2. Slide the card into the slot until it clicks into position.
3. The Remove button should become active within a few seconds, indicating the card is active.
4. If the Remove button stays faded, click the Format button to format the card. NOTE: All data
on the disk will be deleted if the Format button is clicked.
6.2.2
Testing the Playback Function
1. Once the SD card is detected by the system, the button
will turn to
(inactive)
(active).
2. To test the Playback function (this is not required), set up a “Manual Trigger” Recording
Event by clicking Settings > Event > Event Settings.
3. Click the “Add” button on the middle right side of the page to open an “Add Event” box.
4. Give the event a name, like “Test 1”.
19
EAN3120/3220/3300
5. In the “Event Triggered by” field, click on Manual Trigger.
6. Below this, check “Enable This Event”, “Enable Post-trigger Buffer”, and “Record to SD Card”.
7. To save your settings, click OK, or close the box by clicking on the red x icon at top right of the
box (in which case you will be asked if you want to save the data, to which you should reply OK).
The box will close and the new event will be listed in the list area of the Event Settings page.
8. Look at the “Post-trigger Buffer” at the bottom to make sure the buffer time is set to 10 seconds.
9. Click “Apply” to make sure all settings are saved.
10. Click the Live button to go back to the Live page.
11. Get ready to click the Trigger Event button at the bottom of the page. Before you do, see if you
can find something in the view screen that will give you a visual time marker. For instance, if you
can get your hand in front of the camera’s lens, get ready to count down on your fingers.
12. Click the Trigger Event button and slowly count down on your fingers in front of the lens (if you
are able to do so – if not, try to find visual cues on the view screen that will help you to mark the
moment you pushed the trigger). The recording period will be as long as the buffer time you
selected – the default period is 10 seconds.
13. Click the Playback button to open the Playback page.
14. There are different ways to search for recording files on the camera’s Micro SD card (i.e. the
Playback memory). For a recent recording like your test event, simply click the “Search” button
under the “Search by File” header.
15. If the SD card is active and formatted correctly, the recording folder’s name (the recording day’s
date) will appear in the Filename box at the bottom. Click on this folder to open it. If there are
sub-folders, click on the bottom one (the most recent would be at the bottom) until you can click
on a file that cannot open to another sub-level and shows data in the File Information box to the
right. This would be the file of the most recent recording event.
16. To play this file, click the Play button below the video box. The test footage you have recorded
should start playing. Play time should be 10 seconds if you left the Post-trigger Buffer as 10
seconds.
20
EAN3120/3220/3300
6.3
Playing Back Using ARV Viewer
You can play back the recordings stored in the computer using the ARV Viewer
included in the
software CD. To store the recordings in the computer, please refer to Recording List > Copy in 6.1
Playback Window.
4
5
6
3
2
1
7
8
9
10
No.
Item Name
Descriptions
1
Snapshot
Click to take and save a snapshot.
2
Load File
Click to load the recordings for playing back.
3
Convert ARV to AVI
Convert the recording from ARV format to AVI format.
4
Playback Time
Display the playback time.
5
Total Time of Recording
Display the total time of the recording.
6
Stop
Click to stop playing the recording.
7
Step Reverse
Click to display the previous frame.
8
Play
Click to play back the recording.
9
Pause
Click to pause the recording.
10
Step Forward
Click to display the next frame.
21
EAN3120/3220/3300
7 Settings
Click the Settings button on the Live View Window to enter the settings submenu. There are nine buttons
on the left-side of the submenu: Live, System Info, User Config, Network, Video, Audio, User, Event and
System. Click the Live button can go back to the Live View Window.
7.1
System Info
The System Information and System Log can be checked on this page. Click the top tab of the one you
want to see.
7.1.1 Information
Click the Information tab, the following dialog box appears. These values cannot be changed on this
page, and are for reference only.
22
EAN3120/3220/3300
7.1.2 Log
Click the Log tab, the following dialog box appears. The sequence number, date, time and event
messages of the log event will be displayed in the System Log field. The log will display the last 256
log events. Click the Export button to export the system log event list into a “.txt” file and select the
location where the exported log file will be saved to.
23
EAN3120/3220/3300
7.2
User Config
Each user can set a different configuration for his/her Live page here. These settings will be applied to
the logged-in user’s Live page every time he/she logs in.
7.2.1 Live View Config
【Video/Audio Connection Protocol Setting】You can transmit the data stream from the IP cameras
using the RTSP (Real Time Streaming Protocol) on the network. The RTSP is a protocol that allows
you to access video streams by using the compatible media players. Click Apply to apply the
changes or Cancel to cancel the changes and return to the previous settings.




RTP over UDP: The RTSP protocol uses UDP for camera data stream transmission.
RTP over TCP: The RTSP protocol uses TCP for camera data stream transmission.
RTP over HTTP: The RTSP protocol uses HTTP for camera data stream transmission.
Nevio CGI: This is EverFocus’ protocol designed for EverFocus’ IP devices. Select this
protocol for camera data stream transmission.
【Text Settings】Check the box of each option (Machine name, Date/Time, Frame Rate) to display
this info on the Live View Page.
Foreground Color: Slide the Red, Green and Blue bars to create your preferred text color for the
info text line.
Position: Select the position where the text will be displayed. Choose from Upper Left / Lower
Right / Lower Left.
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous
settings.
24
EAN3120/3220/3300
【Date/Time Format Used in Text】Click the dropdown menu to select date/time format from the
listed options. Click on the desired hour format. Click Apply to apply the setting changes or Cancel
to cancel the changes and return to the previous settings.
【Live View Layout Settings】 Check the “Show One Push Buttons” boxes if you want to show these
buttons on the Live View Page. Uncheck these boxes to hide these buttons. This function is only
available for EAN3120 / 3220. Click Apply to apply the setting changes or Cancel to cancel the
changes and return to the previous settings.
7.2.2 Recording / Snapshot
This configures where your Record Button and Snapshot Button (
) files will be saved if
you click one of these buttons. Selectable folders will be on the computer only, not on the
on-camera SD card.
【Recording / Snapshot Export Settings】
Enable Event Recording to PC: Checking this box will let the system save Record/Snapshot Button
recordings to the folder configured below on the user’s PC.
Export Folder: Select the Export folder for the action above by clicking on the browse (…) button,
and then select the desired folder.
File size: Once you click the Record button on the Live View window, the camera will start
recording the live stream to your computer. When a single recording file exceeds the time you set,
the system will create a new file to save that data to.
Overwrite: Select “ON” for overwriting recording/snapshot file when the disk storage capacity is
full. The user can set the storage capacity limitation in the in-sentence field in the gray box below
the Overwrite setting: “If the remaining hard disk capacity is less than ____ MB (50~2000). “
Click Apply to apply the setting changes or Cancel to cancel the changes and return to the
previous settings.
25
EAN3120/3220/3300
7.2.3 Language
Select the language to be displayed on the Web interface of the IP camera. The default language is
English.
To add a new language not listed in the current Language list, click the Browse button to locate
the new language file (.evb) on your computer and then click the Upload button. Updated
language files might be available on the manufacturer’s website. Contact your vendor if required.
Click Apply to apply the setting changes or Cancel to cancel the changes and return to the
previous settings.
Note: Uploading a new language file will cause the system to reboot automatically. Please create
a new network connection to the IP camera when the reboot is complete.
26
EAN3120/3220/3300
7.3
Network
This page covers network-related settings, including Network, DDNS, SMTP/FTP, HTTPS, SNMP, and
Network Alarm.
7.3.1 Network
The following information is required to configure the network settings. Contact your network
administrator or your internet service provider to get the info.
【IP Settings】
IP Type: Refer to the network administrator for these settings of the server. Default: DHCP



DHCP: This setting lets the system use an automatically assigned (dynamic) IP address. This
address can change under certain circumstances. For instance, when the camera’s network
switch/hub has to be rebooted. Do not assign to the DHCP server the same IP addresses used
for the other network cameras and PCs with unique IP addresses.
Static IP: The user can manually set the Static IP address. This type of address is stable and
cannot change, but the user has to make sure there are no address conflicts with other
network-connected devices.
PPPoE: This is a DSL-connection application. The ISP will ask the user to input a username and
password. Contact your ISP for these details.
27
EAN3120/3220/3300
Note: If PPPoE is selected as the IP type, the supplied IP Utility program will not be able to
detect the device.
IP address: When DHCP is not used, the user needs to manually enter the IP address of the
camera. Do not enter an IP address that is already used for your computer or other network
cameras.
Subnet Mask: This field is used to set the netmask for your network, so that the IP camera will be
recognized within the network. Example: 255.255.255.0. When DHCP is selected, the DHCP server
will assign this value automatically.
Gateway: This field is used to set the gateway for your network so that the IP camera will be
recognized within the network. When DHCP is selected, the DHCP server will assign this value
automatically.
Primary DNS: Enter the IP address of the DNS server if this is provided by an ISP.
Secondary DNS: If your ISP provided you with a secondary DNS address, please enter it here.
Username: Enter the account’s username (used only for PPPoE).
Password: Used only for PPPoE.
IPv6: Enter the IPv6 details in this area, if this applies to your system.
Click Apply to apply the setting changes or Cancel to cancel the changes and return to the
previous settings.
【Port Settings】Enter the HTTP, HTTPS and RTSP port numbers. Check the Enable UPnP Port
Forwarding box to enable the UPnP function. Click Apply to save the settings.
Promoted by the UPnP Forum (Universal Plug and Play), the UPnP is a networking architecture
providing compatibility among networked devices listed in the networked device table. Enable the
UPnP function means you can directly connect the cameras listed in the networked device table
by clicking on them.
Note:
1. For the UPnP function to work, an UPnP-enabled router is required.
2. The UPnP function may fail owing to the compatibility between the camera and the router.
【Multicast Settings】Enable if required, fill in the setting options and click Apply to save.
28
EAN3120/3220/3300
7.3.2 DDNS
DDNS (Dynamic Domain Name System) is a service used to map a domain name to the dynamic IP
address of a network device. You can set up the DDNS service for remote access to the IP camera.
DDNS assigns a domain name (URL) to the IP camera, so that the user does not need to go through
the trouble of checking if the IP address assigned by DHCP Server has changed. Once the IP is
changed, the IP camera will automatically update the information to the DDNS to ensure it is always
available for remote access.
Before enabling the following DDNS function, user should have applied for a host name from the
DDS service provider’s website. We support these four DDNS server providers:
www.everfocusddns.com, www.sitelutions.com, www.dyndns.com, and www.no-ip.com
Note: We highly recommend that you use xxxx.everfocusddns.com for the simplicity of setting up
your IP cameras.
【DDNS Settings】
Enable: Check this box to enable the DDNS function.
Service ISP: You can either apply for a host name from EverFocus or other DDNS server providers.
If you choose the EverFocus DDNS server, you can obtain a free host name from EverFocus by
following the steps below:
•
From EverFocus: To obtain a free host name from EverFocus, type a desired host name in the
textbox, click the Register / Update button, and then click the Apply button.
•
From other DDNS server providers: To obtain a domain name from one of the three DDNS
server providers, you have to register your name with the provider first, and then select the
provider and fill in the required information. Please refer to the specific DDNS company’s
website for further information.
Record ID: Type the record ID if provided by the DDNS server provider.
29
EAN3120/3220/3300
FQDN: Type the fully qualified domain name applied from the DDNS server provider. For
example, xxxx.dyndns.com
Username / Password: Type the login account of your DDNS server provider.
Click Apply to apply the setting changes or Cancel to cancel the changes and return to the previous
settings.
Note:
1. In order to support the full functionality of the camera, you must open the port numbers (80,
554, 443) on the router for remote access to the IP camera. This function is available on most
routers in the market and is often known as “Port Forwarding”. To set up Port Forwarding,
please consult the manual of the router.
2. In certain router models, it is possible that you will not be able to access the camera using
DDNS while inside the router’s network. Please try using a PC located outside of your router’s
network.
Default Ports on All EverFocus IP Cameras:
HTTP: 80
RTSP: 554
HTTPS: 443
30
EAN3120/3220/3300
7.3.3 SMTP / FTP
【Set SMTP Server (email)】This area is for configuring the mail server that is used to send e-mail
text notifications and one image file from the camera to predefined addresses via SMTP. Note that
to enable e-mail notification function, you have to check the Send Mail Notification item on the
Event dialog box (see 7.7.1 Event Settings).
SMTP Server: Enter the IP address or the host name of the SMTP server used to send e-mails.
SMTP Port: Enter the port number for SMTP. The default is 25.
Authentication: Check this box if the SMTP server requires authentication (user/password).
User name: Input the user’s login ID if the SMTP server requires authentication.
Password: Input the user’s login password if the SMTP server requires authentication.
Receiver Address: Input the e-mail addresses for receiving an e-mail message when an EVENT is
enabled and triggered. Please use “;” to separate multiple addresses.
31
EAN3120/3220/3300
Sender Address: Input the sender’s e-mail address, so that the receiver can recognize the sender
when an Event message is received.
Attach Image: Check this box if you want to attach an image when an alarm is triggered or an IP
camera detects events.
This server requires a secure connection (SSL): Check this box to enable the SSL function. Enable
this function means you can access the camera through the SSL protocol that provides
communication security over the Intern
Send Test Email: Click the Test button to send a testing email to the assigned address.
Click Apply to apply the setting changes or Cancel to cancel the changes and return to the
previous settings.
【Set FTP Server】The settings relating to the FTP server used to transmit the alarm recordings can
be configured here. Note that to enable uploading recordings to the FTP server function, you have
to check the Upload to FTP item on the Event dialog box (see 7.7.1 Event Settings).
FTP Server: Enter the IP address or the host name of the FTP server.
FTP Port: Enter the port number for the FTP server. Default is 21.
Recording Path: Assign the recording path.
User Name: Set FTP User’s name.
Password: Set FTP password.
PASV mode: Check to enable Passive mode. Passive mode is normally enabled. If a connection
cannot be established, uncheck "PASV Mode”.
Test FTP Server: Click the Test button to send a testing file to the assigned FTP server.
Click Apply to apply the setting changes or Cancel to cancel the changes and return to the previous
settings.
32
EAN3120/3220/3300
7.3.4 HTTPS
Hypertext Transfer Protocol Secure (HTTPS) is a combination of the Hypertext Transfer Protocol
and the SSL/TLS protocol that provides encrypted communication and secure identification of a
network web server.
Before using the HTTPS function for communication with the IP camera, a Certificate must be
created first. There are two ways to create and install a certificate: Create Self-Signed Certificate
and Create Certificate Request.
Create Self-Signed Certificate
Please note that even though self-signed certificates are free and offer some protection, true
security is only implemented after the installation of a signed certificate issued by a certificate
authority.
1. Click the Create Self-Signed Certificate button, the following dialog appears.
33
EAN3120/3220/3300
2. Type the required Certificate information and then click the Apply button. The subject line will
be displayed in the Installed Certificate Information field.
3. Click the Property button, a pop-up window appears to display the details of the certificate.
4. To optionally create and install other certificates, remove the existing one by clicking the
Remove button to erase the certificate.
5. On the Web page, change the address from “http://” to https:// in the address bar and press
Enter on the keyboard. Some Security Alert dialogs will pop up. Click OK or Yes to enable HTTPS.
Create Certificate Request
You can apply for an official certificate from an issuing Certificate Authority.
1. Click the Create Certificate Request button, the following dialog appears.
34
EAN3120/3220/3300
2. Type the required Certificate information and then click the Apply button. The subject line will
be displayed in the Created Request field
3. Click the Property button, a pop-up window appears to display the details of the certificate.
4. To optionally create and install other certificates or request, remove the existing one by clicking
the Remove button to erase the certificate or request.
5. Copy the contents of the Certificate request (in PEM format) and paste it to the certificate
request field on the Web page of the 3rd-party certification authority such as Symantec VeriSign.
Wait for the certificate authority to issue an SSL/TLS certificate and then download the issued
certificate on your computer.
6. In the Install Signed Certificate field, click the Browse button to search for the issued certificate,
and then click the Upload button to import the certificate. Once the certificate has been
uploaded, this field will show the subject line of the certificate.
35
EAN3120/3220/3300
7.3.5 SNMP
The default values for SNMP v1/v2/v2c and SNMP v3 are already filled in. Click either of the
Enable buttons to enable either of the two. Make your changes as desired. Click on the Trap
Address field to enter the digits, if required.
7.3.6 Network Alarm
This function works with EverFocus’s CMS software, e.g. PowerVideo Plus. For the setting details,
please refer to the CMS network alarm protocol.
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous settings.
36
EAN3120/3220/3300
7.4
Video
The settings relating to video such as streaming, camera OSD can be configured on this page.
7.4.1 Multi Streaming
【Stream Settings】 This IP camera can output three video streams simultaneously. For each of these
streams, the user can set the compression format, resolution, bit rate, and frame rate individually.
Note: If you connect to the camera via the Internet and experience a delay (lag time) in the video
feed, try to reduce the number of streams and the quality and resolution of the streams – but
keep the frame rate at its maximum.
37
EAN3120/3220/3300
Enable: This option is only for enabling the stream for live view (see Video Stream in 5.4 Live View
Window). Stream 1 is always enabled for live view. To enable Stream 2 and/or Stream 3 for Live
View, check the “Enable” box.
Format: Select the encoding format – H.264 or MJPEG.
Resolution: Select the most suitable resolution for your needs.
Frame Rate: Select from 1 to 30 fps.
Bit Rate: If required, select whether you want the stream to stream a Constant Bit Rate or a
Variable Bit Rate, and set the values of whichever option you choose.
【Video Recording Settings】Select the desired video stream and recording format to record the
videos to SD card. Before using this function, you have to configure the stream settings in the Stream
Settings field above.
【Video Overlay Settings】 Select to overlay the video title or date/time on the live video streams
and snapshots.
Show video title in video and snapshots: Select to overlay video title on the video streams and
snapshots. Type a title name in the Video Title field and then select a position from the Position
drop-down list where you want to display the video title.
Date/Time: Select to overlay date and time on the video streams and snapshots. Select a date and
time format; and then select a position from the Position drop-down list where you want to display
the date and time.
Click Apply to apply the changes, or Cancel to cancel the changes and return to the previous
settings.
38
EAN3120/3220/3300
7.4.2 Camera
You can configure the basic camera settings on this page.
【Profile Settings】 The Profile Setting is designed with four camera modes (Vivid/High Contrast,
Standard, More Detail and User Define), which can be applied in various scenes to enhanced image
quality. You can apply different camera modes to the daytime and night time.
Day Mode: Select a camera mode and then click the Apply button to save the settings.
 Vivid: Select Vivid mode to have images with optimized contrast ratio. You can further
configure the camera settings on the Advanced setup page if required. Note that selecting the
Vivid mode will lock (grayed-out) some Camera Settings on the Advanced setup page such as
Exposure Settings (AE), Noise Reduction Settings and Monitor Settings.
 Standard: Select Standard mode to have images with system configured settings. You can
further configure the camera settings on the Advanced setup page if required. Note that
selecting the Vivid mode will lock (grayed-out) some Camera Settings on the Advanced setup
page such as Exposure Settings (AE), Noise Reduction Settings and Monitor Settings.
 More Detail: Select More Detail mode to enhance the dark parts of the images. You can
further configure the camera settings on the Advanced setup page if required. Note that
selecting the Vivid mode will lock (grayed-out) some Camera Settings on the Advanced setup
page such as Exposure Settings (AE), Noise Reduction Settings and Monitor Settings.
 User Define: Select User Define mode to customize the camera settings. You can configure all
the camera settings on the Advanced setup page.
39
EAN3120/3220/3300
Flicker Compensation: Check the box to enable the Flicker Compensation function. Please enable
this function only if flicker artifacts are observed.
Night Mode: Select a camera mode and then click the Apply button to save the settings.




High Contrast: Select High Contrast mode to have images with higher contrast ratio. You can
further configure the camera settings on the Advanced setup page if required. Note that
selecting the Vivid mode will lock (grayed-out) some Camera Settings on the Advanced setup
page such as Exposure Settings (AE), Noise Reduction Settings and Monitor Settings.
Standard: Select Standard mode to have images with system configured settings. You can
further configure the camera settings on the Advanced setup page if required. Note that
selecting the Vivid mode will lock (grayed-out) some Camera Settings on the Advanced setup
page such as Exposure Settings (AE), Noise Reduction Settings and Monitor Settings.
More Detail: Select More Detail mode to enhance the dark parts of the images. You can
further configure the camera settings on the Advanced setup page if required. Note that
selecting the Vivid mode will lock (grayed-out) some Camera Settings on the Advanced setup
page such as Exposure Settings (AE), Noise Reduction Settings and Monitor Settings.
User Define: Select User Define mode to customize the camera settings. You can configure all
the camera settings on the Advanced setup page.
Blur Compensation: Check the box to enable the Blur Compensation function. Please enable this
function only if motion blur is observed.
【Camera Settings】
Mirror: Switch Mirror ON to rotate the image horizontally around a vertical axis.
Flip: Switch Flip ON to rotate the image vertically around a horizontal axis.
BLC: Back Light Compensation (BLC) is used to make the subject appear clearer when it is set against
a bright background.
 OFF: Select to switch Back Light Compensation functions off.
 ON (BLC): The BLC can increase the exposure of a dark area surrounded by a brighter area,
HLC can decrease the exposure of bright areas surrounded by darker areas. This enables the
camera to better display information that would otherwise have been “whited out”, like a
license plate between two bright headlights on a dark road.
 ON (HLC): The Highlight-Suppression BLC is used to reduce the brightness of light sources in a
specific area. It is activated only in a low illumination environment to minimize the effects of
glare from bright lights such as spotlights, street lights or headlights in the field of view.
40
EAN3120/3220/3300
WDR: This function is not available for EAN3300. The Wide Dynamic Range (WDR) function provides
clearer images when both of the very bright and dark areas simultaneously appear on the camera
view. There are four value options: OFF, Low, Middle and High. Note that when WDR is ON, some
parts of the image may appear solarized. This is normal for WDR, and is not a camera malfunction.
D/N Mode







Auto: Select to let the camera automatically switch to Night mode (black and white images
with IR LED on) when the light levels fall to a specified level, and back to Day mode (color)
when the light levels rise to a specified level.
Day: Select to keep the camera in Day mode (color images with IR LED off), even in nighttime.
Night: Select to keep the camera in Night mode (black and white images with IR LED on), even
in daytime.
Schedule: Select to let the camera to switch to Day mode or Night mode (IR LED on) based on
the day and night schedule settings. To configure the daytime / nighttime of each day, please
refer to 7.4.6 Schedule.
Auto mode without IR LED: Select to let the camera automatically switch to Night mode
(black and white images with IR LED off) when the light levels fall to a specified level, and back
to Day mode (color) when the light levels rise to a specified level.
Night mode without IR LED: Select to keep the camera in Night mode (black and white images
with IR LED off), even in daytime.
Schedule without IR LED: Select to let the camera to switch to Day mode or Night mode (IR
LED off) based on the day and night schedule settings. To configure the daytime / nighttime of
each day, please refer to 7.4.6 Schedule.
【DC Iris Calibration】This function is only available for EAN3300.
Calibration Start: Click to set an ideal Iris Stable value for the camera. Before clicking the button, you
have to aim the camera at an intense light such as florescent lighting. If the calibration succeeds, the
new value will show on the Iris Stable text field. Calibration may fail due to the darkness of the
environment or the altering light.
Info: Shows the processing status or result of the calibration.
Iris Stable: Displays the Iris Stable value after clicking the Calibration Start button. You can also
manually adjust the Iris Stable value.
Default Value: The default Iris Stable value is 122.
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous settings.
【Control】The camera features 10x digital zoom. Click the
zoom out the image.
41
or
button to zoom in or
EAN3120/3220/3300
7.4.3 Advanced
You can further set up camera settings on this page. Note that to enable all the setting items, you
have to select User Define from the Day Mode / Night Mode drop-down list in 7.4.2 Camera.
EAN3120:
【Control】The camera features 10x digital zoom. Click the
or
button to zoom in or
zoom out the image.
Day: Select Day to set up the following settings for daytime and then click the Apply button to save
the settings.
Night: Select Night to set up the following settings for nighttime and then click the Apply button to
save the settings.
42
EAN3120/3220/3300
【Camera Settings】
Exposure Settings (AE): This setting is used to adapt to the amount or type of light used by the
camera.
Mode:
 ALC (Shutter Priority): Selecting ALC (Automatic Light Control) allows the camera circuitry to
either take bright spots more into consideration (peak), bringing out detail in bright areas, or
less into consideration (average) bringing out detail in shadows.
 AES (Iris Priority): Selecting AES (Auto Electronic Shutter) disables the Shutter setting below
this setting. In this mode, the camera measures the light level and decides whether it needs
more or less light and then automatically adjusts the shutter speed accordingly.
Shutter: If enabled, this setting lets you set the shutter speed yourself (measured in fractions of a
second).
Shutter Limit: Set the Shutter limit here.
AGC Limit: Set the Auto Gain Control limit here. The lower the AGC level, the lower the video signal
and the noise. However, the image will be darker under low-light condition with IR-off if you set up
the Iris to the maximum level.
Brightness: Set the image brightness here.
AE Reference: Set the Auto Exposure value here.
Black Level: Set the Black level here.
BLC Settings: Back Light Compensation (BLC) is used to make the subject appear clearer when it is
set against a bright background.
 OFF: Select to switch Back Light Compensation functions off.
 ON (BLC): This option is useful when the background of the subject is very bright and the
subject itself is dark. The BLC will measure the light of the image center and the lens iris will
automatically set for optimal image quality.
Select ON (BLC), the
button next to the Mode drop-down list will be active (see image
below). Click the
button, the green setup areas appear on the left screen. Click on the
areas to enable / disable the BLC function. The selected areas (in green) will be applied with
the BLC function.

ON (HLC): This option is only available when you select AES Mode in the Exposure Settings (AE)
field. This function is useful when the bright highlights, such as flashlight or car headlights,
appear on the camera view. The higher the value, the more the highlight compensation.
Select ON (HLC), and then select a level from the drop-down list. The higher the level, the more
the highlight compensation.
43
EAN3120/3220/3300
Noise Reduction Settings: This limits the amount of digital “video noise” that is usually found in
any video stream, and helps to reduce file size. The higher the level, the more the reduction.
Select ON / OFF to enable / disable the Noise Reduction function. Or select Auto to let the camera
automatically enable / disable the Noise Reduction function. Slide the Level bar to set up the level.
The higher the level, the more the reduction.
WDR: The Wide Dynamic Range (WDR) function provides clearer images when both of the very
bright and dark areas simultaneously appear on the camera view. There are four value options: OFF,
Low, Middle and High. Note that when WDR is ON, some parts of the image may appear solarized.
This is normal for WDR, and is not a camera malfunction.
White Balance Settings: Select the mode that delivers the best quality image for the camera’s light
environment.
 Auto: Select to let the camera automatically adjust the White Balance. In the Auto mode the
camera computes the white balance value output using color information from the entire
screen. It outputs the proper value using the color temperature radiating from a black subject
based on a range of value from 3000 to 7500K.
 Manual: Select to adjust the Red and Blue values yourself in the fields below this field.
 Indoor: Select to use the default settings for indoor environments. In the Indoor mode, the
camera uses 3200K as the base value.
 Outdoor: Select to use the default settings for outdoor environment. In the Outdoor mode, it
uses 5800K as the base value.

One Push: Select to enable the Push button
next to the Mode drop-down field. This will
allow you to force the camera to readjust the white balance every time you push the Push
button. The lens will hold the same focal position until the next trigger command is received.
This function helps to prevent incorrect focusing in dark environments.
Day/Night Settings:
 Auto: Select to let the camera automatically switch to Night mode (black and white images
with IR LED on) when the light levels fall to a specified level, and back to Day mode (color)
when the light levels rise to a specified level.
 Day: Select to keep the camera in Day mode (color images with IR LED off), even in nighttime.
 Night: Select to keep the camera in Night mode (black and white images with IR LED on), even
in daytime.
 Schedule: Select to let the camera to switch to Day mode or Night mode (IR LED on) based on
the day and night schedule settings. To configure the daytime / nighttime of each day, please
refer to 7.4.6 Schedule.
44
EAN3120/3220/3300
Sharpness Settings: Select the sharpness level of the image. A low sharpness level will deliver a
softer, less detailed image. A high level will deliver a sharp, highly detailed image. Switch Resolution
Enhancement ON to enable the resolution enhancement function.
Saturation: Set the saturation value.
Monitor Settings: The user can use this field to optimize video quality of the monitor.
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous
settings.
45
EAN3120/3220/3300
EAN3220:
【Control】The camera features 10x digital zoom. Click the
or
button to zoom in or
zoom out the image.
Day: Select Day to set up the following settings for daytime and then click the Apply button to save
the settings.
Night: Select Night to set up the following settings for nighttime and then click the Apply button to
save the settings.
46
EAN3120/3220/3300
【Camera Settings】
Lens (IRIS Control): Select DC or Manual for IRIS control.
Exposure Settings (AE): This setting is used to adapt to the amount or type of light used by the
camera.
Shutter: If enabled, this setting lets you set the shutter speed yourself (measured in fractions of a
second).
AGC: Set the Auto Gain Control limit here. The lower the AGC level, the lower the video signal and
the noise. However, the image will be darker under low-light condition with IR-off if you set up the
Iris to the maximum level.
Slow Shutter: This option can be switched on when Auto or 1/30 option is selected in the Shutter
field.
Brightness: Set the image brightness here.
Black Level: Set the Black level here.
WDR Settings: The Wide Dynamic Range (WDR) function provides clearer images when both of the
very bright and dark areas simultaneously appear on the camera view. There are three value
options: Low, Middle and High. Note that when WDR is ON, some parts of the image may appear
solarized. This is normal for WDR, and is not a camera malfunction.
Visibility Enhancement: (OFF/Low/Middle/High) Images in foggy or rain environments or in
environments with a very strong luminous intensity have a dynamic range that is significantly lower
than ordinary images. The user can use this Visibility Enhancement setting to “DEFOG” the image if
such “FOGGING” is an issue.
BLC Settings: Back Light Compensation (BLC) is used to make the subject appear clearer when it is
set against a bright background.
 OFF: Select to switch Back Light Compensation functions off.
 ON (BLC): This option is useful when the background of the subject is very bright and the
subject itself is dark. The BLC will measure the light of the image center and the lens iris will
automatically set for optimal image quality.
You can configure one area to apply the BLC function. Select ON (BLC), the setup buttons
appears (see image below). Select Low / Middle / High from the BLC Gain drop-down list. To
set up a BLC area, click the Edit Area button and then click on the blue color tab to turn your
mouse cursor into a blue pen. Move the cursor to the position on the right screen where you
want the BLC rectangle to start and then click. Move your cursor to the position (diagonally
opposing corner) where you want the BLC rectangle to end and then click. The blue area will
be applied with the BLC function.
47
EAN3120/3220/3300

ON (HLC): This function is useful when the bright highlights, such as flashlight or car headlights,
appear on the camera view. The higher the value, the more the highlight compensation.
HLC Level: Select a level for the HLC setting. The higher the level, the more the highlight
compensation.
HLC Mode: Select All Day / Night mode to apply the HLC function.
HLC Black Mask: Select On / Off to apply the black mask on the selected areas. The
over-exposure portions within the selected areas will be applied with the black mask.
Color Tabs: You can set up four HLC areas with different colors. To set up a HLC area, click the
Edit Area button and then click on the color tab to turn your mouse cursor into a pen of that
color. Move the cursor to the position on the right screen where you want the HLC rectangle
to start and then click. Move your cursor to the position (diagonally opposing corner) where
you want the HLC rectangle to end and then click. Select ON from the color tab drop-down list.
The rectangular area with the selected color will be applied with the HLC function.
Noise Reduction Settings: This limits the amount of digital “video noise” that is usually found in any
video stream, and helps to reduce file size. The higher the level, the more the reduction.
2D DNR: Select ON to enable the 2D DNR function.
3D DNR: Select ON to enable the 3D DNR function. You can further set up the following settings.
 3D Start AGC: Set up the AGC level to automatically start the 3D NR function.
 3D End AGC: Set up the AGC level to automatically stop the 3D NR function.
 3D Level: Set up the 3D DNR level.
 Smart NR: Select ON to enable the Smart NR function. The 3D NR function will be
automatically turned on when a motion event occurs.
48
EAN3120/3220/3300
White Balance Settings: Select the mode that delivers the best quality image for the camera’s light
environment.
 Auto: Select to let the camera automatically adjust the White Balance. In the Auto mode the
camera computes the white balance value output using color information from the entire
screen. It outputs the proper value using the color temperature radiating from a black subject
based on a range of value from 3000 to 7500K.
 Manual: Select to adjust the Red and Blue values yourself in the fields below this field.
 Indoor: Select to use the default settings for indoor environments. In the Indoor mode, the
camera uses 3200K as the base value.
 Outdoor: Select to use the default settings for outdoor environment. In the Outdoor mode, it
uses 5800K as the base value.

One Push: Select to enable the Push button
next to the Mode drop-down field. This will
allow you to force the camera to readjust the white balance every time you push the Push
button. The lens will hold the same focal position until the next trigger command is received.
This function helps to prevent incorrect focusing in dark environments.
Day/Night Settings:
 Auto: Select to let the camera automatically switch to Night mode (black and white images
with IR LED on) when the light levels fall to a specified level, and back to Day mode (color)
when the light levels rise to a specified level.
 Day: Select to keep the camera in Day mode (color images with IR LED off), even in nighttime.
 Night: Select to keep the camera in Night mode (black and white images with IR LED on), even
in daytime.
 Schedule: Select to let the camera to switch to Day mode or Night mode (IR LED on) based on
the day and night schedule settings. To configure the daytime / nighttime of each day, please
refer to 7.4.6 Schedule.
Negative: Switch this setting ON to view a color negative version of the video image. This is useful
at night or when viewing temperature-sensitive images.
Sharpness Settings: Select the sharpness level of the image. A low sharpness level will deliver a
softer, less detailed image. A high level will deliver a sharp, highly detailed image. Switch Resolution
Enhancement ON to enable the resolution enhancement function.
Contrast: Select the contrast level of the image.
Monitor Settings: The user can use this field to optimize video quality for specific type of monitor –
LCD or CRT.
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous settings.
49
EAN3120/3220/3300
EAN3300:
50
EAN3120/3220/3300
【Control】The camera features 10x digital zoom. Click the
zoom out the image.
or
button to zoom in or
Day: Select Day to set up the following settings for daytime and then click the Apply button to save
the settings.
Night: Select Night to set up the following settings for nighttime and then click the Apply button to
save the settings.
【Camera Settings】
Lens (IRIS Control): Select DC or Manual for IRIS control.
Exposure Settings (AE): This setting is used to adapt to the amount or type of light used by the
camera.
Mode:
 ALC (Shutter Priority): Selecting ALC (Automatic Light Control) allows the camera circuitry to
either take bright spots more into consideration (peak), bringing out detail in bright areas,
or less into consideration (average) bringing out detail in shadows.
 AES (Iris Priority): Selecting AES (Auto Electronic Shutter) disables the Shutter setting below
this setting. In this mode, the camera measures the light level and decides whether it needs
more or less light and then automatically adjusts the shutter speed accordingly.
 Manual: Select this option to manually set up the Shutter (Manual) and AGC (Manual)
values.
Shutter (Manual): If enabled, this setting lets you set the shutter speed yourself (measured in
fractions of a second). This option can be switched on when ALC or Manual Mode is selected.
AGC (Manual): Set the Auto Gain Control limit here. The lower the AGC level, the lower the video
signal and the noise. However, the image will be darker under low-light condition with IR-off if
you set up the Iris to the maximum level. This option can be switched on when Manual Mode is
selected.
Slow Shutter: This option can be switched on when AES Mode is selected in the Exposure
Settings (AE) field.
AGC: Set the Auto Gain Control limit here. The lower the AGC level, the lower the video signal
and the noise. However, the image will be darker under low-light condition with IR-off if you set
up the Iris to the maximum level.
Flickerless: If the Mode field in the Exposure Settings (AE) area has been set to AES, then this
option becomes available. Choose between OFF, 50HZ, 60HZ, 50HZ (High Luminance) or 60HZ
(High Luminance).
EV Setting: Set up the Exposure Value. Note the brightness of the screen changes when you
change the EV value.
AE Response: Set up the Auto Exposure Response time.
51
EAN3120/3220/3300
AE Weighting Area: Select an AE Weighting area. Each setup AE Weighting Area is configured
with the appropriate brightness level on the center and the surrounding areas.
Brightness: Set the image brightness here.
Black Level: Set the Black level here.
BLC Settings: Back Light Compensation (BLC) is used to make the subject appear clearer when it is
set against a bright background.
 OFF: Select to switch Back Light Compensation functions off.
 Back Light: The Back Light function is useful when the background of the subject is very bright
and the subject itself is dark. Select Back Light and adjust the slide bar to the left / right for
setting up the back light value. The higher the value, the more the backlight compensation.
 Front Light: This function is useful when the bright highlights, such as flashlight or car
headlights, appear on the camera view. Select Front Light and adjust the slide bar to the left /
right for setting up the front light value. The higher the value, the more the highlight
compensation.
Noise Reduction Settings: This limits the amount of digital “video noise” that is usually found in any
video stream, and helps to reduce file size. The higher the level, the more the reduction. Select ON
/ OFF to enable / disable the Noise Reduction function. Or select Auto to let the camera
automatically enable / disable the Noise Reduction function. Slide the Level bar to set up the level.
The higher the level, the more the reduction.
White Balance Settings: Select the mode that delivers the best quality image for the camera’s light
environment.
 Auto: Select to let the camera automatically adjust the White Balance. In the Auto mode the
camera computes the white balance value output using color information from the entire
screen. It outputs the proper value using the color temperature radiating from a black subject
based on a range of value from 3000 to 7500K.
 Manual: Select to adjust the Red and Blue values yourself in the fields below this field.
 Indoor: Select to use the default settings for indoor environments. In the Indoor mode, the
camera uses 3200K as the base value.
 Outdoor: Select to use the default settings for outdoor environment. In the Outdoor mode, it
uses 5800K as the base value.
 Manual Temperature: Select to use the optimized Red and Blue settings. You can also
optionally adjust the Manual Level below this field for setting up the color temperature. The
higher the value, the more the color temperature.
52
EAN3120/3220/3300
Day/Night Settings:
 Auto: Select to let the camera automatically switch to Night mode (black and white images
with IR LED on) when the light levels fall to a specified level, and back to Day mode (color)
when the light levels rise to a specified level.
 Day: Select to keep the camera in Day mode (color images with IR LED off), even in nighttime.
 Night: Select to keep the camera in Night mode (black and white images with IR LED on), even
in daytime.
 Schedule: Select to let the camera to switch to Day mode or Night mode (IR LED on) based on
the day and night schedule settings. To configure the daytime / nighttime of each day, please
refer to 7.4.6 Schedule.
Saturation: Set the saturation value.
Negative: Switch this setting ON to view a color negative version of the video image. This is useful
at night or when viewing temperature-sensitive images.
Sharpness Settings: Select the sharpness level of the image. A low sharpness level will deliver a
softer, less detailed image. A high level will deliver a sharp, highly detailed image. Switch Resolution
Enhancement ON to enable the resolution enhancement function.
Auto Contrast: Select the contrast level of the image.
Suppress Function:
Aperture Compensation Suppression: (OFF/Low/Middle/High) This setting can be activated to
suppress luminance noise when the AGC level increases.
Chroma Suppression: (OFF/Low/Middle/High) This setting can be activated to suppress
chrominance noise when the AGC level increases.
Monitor Settings: The user can use this field to optimize video quality of the monitor.
Shading Correction: Shading correction is used to compensate the insufficient illumination on the
peripheral of the image. The larger the number is, the brighter the image will be.
 Up: Use the slide bar to correct the uneven illumination on the upper side of the image.
 Right: Use the slide bar to correct the uneven illumination on the right side of the image.
 Down: Use the slide bar to correct the uneven illumination on the lower side of the image.
 Left: Use the slide bar to correct the uneven illumination on the left side of the image.
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous settings.
53
EAN3120/3220/3300
7.4.4 ROI (Region of Interest)
The Region of Interest (ROI) function allows users to set up multiple regions within an image with
better quality and less distortion than the rest of the image. You can also use this function
together with the Digital Zoom function on the Live View Page to get a better image result. Up to
eight ROIs can be configured in the ROI settings page.
To set up an ROI region:
1.
2.
3.
4.
5.
Select an ROI number from the ROI No. drop-down list.
Click the Add button, the mouse cursor will turn into a pen when you move it over the live
image on the left.
Move the cursor to the position where you want the ROI rectangle to start and then click.
Move the cursor to the position (diagonally opposing corner) where you want the ROI
rectangle to end and then click.
Slide the Quality bar to set up the quality value.
Click the Apply button to apply the settings, or click the Cancel button to reset without saving
the settings.
54
EAN3120/3220/3300
7.4.5 Privacy Mask
The Privacy Mask can block out sensitive areas from view, covering the areas with colored or black
and white boxes in both live view and recorded clips. This feature is useful when users’ don’t want
the sensitive information visible. Up to four Privacy Masks can be configured.
【Privacy Mask Color Settings】The Modes vary among camera models.
Mode: Click Color to make the masks appear as colored rectangles on the screen. Click B/W to
make the masks appear as gray rectangles on the screen. Click Mosaic to make the masks appear
as mosaic-effect rectangles on the screen.
Level: Select the color of the masks if you selected Color Mode. Select the level of grayness of the
masks if you selected B/W Mode. Select the level of small/middle/large if you selected Mosaic
Mode.
Color Tabs
: Click on a color tab to turn your mouse cursor into a pen of that color.
You can now create a block of that color on the video screen. Move your cursor to the position
where you want your mask rectangle to start and then click. Move your cursor to the position
(diagonally opposing corner) where you want your mask rectangle to end and then click. The
rectangular area with the selected color will appear. The live image will display the rectangular
area with the color you selected. If you want to create another mask, use one of the other three
colors. Each color denotes a different mask area. Only one block per color is allowed. As the
number of colors suggests, you can configure up to four blocks.
Select All: Click to turn the whole screen into a mask area.
Clear All: Click to delete all configured mask blocks.
Eraser: Click to turn the mouse cursor into an eraser to delete any block you click on.
Area: Shows the color and number of the block.
Enable: Check this box to enable the related mask block.
Click Apply to apply the settings or Cancel to cancel the changes and return to the previous
settings.
55
EAN3120/3220/3300
7.4.6 Schedule
The Schedule setup page is designed for users to configure the daytime and nighttime of each day.
The Schedule setting is only functional if you select Schedule or Schedule without IR LED from the
D/N Mode drop-down list on the Camera setup page.
Select Night and then move the cursor on the desired time square, click and drag the cursor over the
time squares to configure them to the Night mode (blue color). Select Day and then move the cursor
on the desired time square, click on the time squares to configure them to the Day mode (gray
color).
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous settings.
56
EAN3120/3220/3300
7.5
Audio
The camera can transmit audio to your computer if you have connected an external microphone /
line-in (TRS) audio device to its audio Input.
Check the Enable Audio box to enable the camera’s audio input function and then adjust the audio
input volume. Note that the camera provides a line-in 3.5mm jack (TRS), therefore, TRS microphones
with a (built-in) amplifier and external power supply are required. Click Apply to apply the changes or
Cancel to cancel the changes and return to the previous settings.
57
EAN3120/3220/3300
7.6
User
7.6.1 User Information
The system administrator can create up to ten user accounts on this page.
To set up a user account:
1. Highlight a user account and click the Modify button. The following dialog box appears.
2. Type the account name, account description and password for the account. Type the password
again in the Confirm field.
3. Select an authority level for the user account from the Authority drop-down list.
•
Supervisor / Administrator: The only difference between a supervisor and administrator is
that a supervisor can edit an administrator’s account and password, but an administrator
cannot edit the supervisor’s account and password. Multiple administrators can be
configured, but there can be only one supervisor. The supervisor and administrators all
have unrestricted access to the Settings submenus and can determine the registration of
all other users.
58
EAN3120/3220/3300
•
4.
5.
6.
7.
User: A user can view the Live View page and view the system, network, video, and audio
information. A user can only adjust the User Config page settings. The user does not have
access to the User, Event and System pages.
• Guest: The lowest level of access, which only allows the user access to the Live View page.
Select Active or Disable from the Status drop-down list to active or disable the user account.
Click On in the SD Card Playback field to allow the user to access the SD card playback
function.
Click OK.
Click Apply to save all the settings.
59
EAN3120/3220/3300
7.6.2 IP Address Filter
Use this page to specify IP addresses that are not allowed to access this camera. By default, any IP
address can access the camera.
Note: The Allowed List addresses only become relevant when the Denied List contains a network
or range, and the supervisor wants to allow one or more IP addresses within that excluded range
or network. In such a scenario, the user would enter the excluded range or network in the
Denied List, and enter the exceptions in the Allowed List.
To set up the IP Address Filter:
1. Select Denied List. Click the Add button, the following dialog box appears.
2. Select an IP type from the IP Type drop-down list.
3. Select a network rule from the Rule drop-down list, type the IP address and click OK.
Single: Type a single IP address in the IP Address field below.
Network: Type the IP address and subnet mask in the field below.
Range: Type a range for the IP addresses.
4. If you have set up an IP range in Step 3, you can optionally set up the Allowed List to allow one
or more IP addresses within the setup IP range to access the IP camera.
5. Click Apply.
60
EAN3120/3220/3300
7.7
Event
You can set up the Motion Detection event, Tamper Detection event or the Alarm I/O to automatically
notify the users when an event occurs or an alarm is triggered. You can also set up a schedule to
automatically record the videos when an event occurs or an alarm is triggered.
7.7.1 Event Settings
You can create a total of ten event or alarm settings page in the Event List
【Event List】
Click the Add button, and the following Event Configuration Window appears.
61
EAN3120/3220/3300
Enter Event Name: Type an event name.
Event Triggered by: Select an event or alarm type for the to-be-specified-below reaction/s.
Alarm Input: Select this if you want a reaction trigger coming from any external, connected sensor
to activate a to-be-specified-below reaction/s via the camera system. Make sure that a suitable
device is actually connected to the alarm input relay.
Manual Trigger: Select this option if you want to manually trigger the alarm by clicking the Trigger
Event button on the Live View Page.
Motion Detection: Select this option if you want motion in a specified part of the camera’s viewing
rectangle (the screen image) to trigger the to-be-specified-below reaction/s.
Tampering Detection: Select this option if you want the camera’s tampering detection sensor to
trigger the to-be-specified-below reaction/s. You can set up the tamper duration time in 7.7.3
Tamper Detection.
Schedule Recording: Select this option if you want the Schedule Recording periods configured in
the recording schedule (the Settings > Event > Schedule page) to activate this event. In this
scenario, a preconfigured event reaction like a log entry will list the start and end times of each
period. Actual recording will only be triggered if the event is preconfigured to do so.





Enable This Event: Select to activate the event.
Enable Re-trigger: Click to set a minimum time after the event is triggered before the event
can be triggered again.
Enable Pre-trigger Buffer: Click if you want the Event reaction (as selected in the “Notification
Over” field below) to be the activation of the video recording function, and if you want the
recording to include the video feed from the time period (configurable on the previous “Event
Settings” page) just before the Event trigger occurred.
Enable Post-trigger Buffer: Click if you want the Event reaction (as selected in the Notification
Over field) to be the activation of the video recording function, and if you want the recording
to include the video feed from a time period (configurable on the Event Settings page) just
after the Event trigger occurred.
Motion Area: Select a setup motion detection area from the drop down list. Note this
function only becomes relevant after the Motion Detection areas have been set up (see 7.7.2
Motion Detection).
Notification Over: Select the desired notification types form the following items.


Log: Click if you want the camera to list the event’s details in its log if the event is triggered.
Trigger Alarm Output: Click if you want the camera to relay the event reaction to a device
attached to the alarm relay output wire and then set up the alarm output duration time.
62
EAN3120/3220/3300



Send Mail Notification: Click if you want the camera to send an email text notification and
one image file to the email address entered in the Set SMTP Server(email) field of the
Network > SMTP/FTP page, if the Event occurs (see 7.3.3 SMTP / FTP).
Upload to FTP: Click if you want the camera to upload the recordings to the FTP server
entered in the Set SMTP Server(email) field of the Network > SMTP/FTP page, if the Event
occurs (see 7.3.3 SMTP / FTP).
Record to SD Card: Click if you want the camera to start recording its video feed (when the
event occurs) on an on-camera SD Card (if such a card has been inserted).
Note: The recording will only be as long as the combined Pre- and Post-trigger Buffers, so
make sure you enable at least one of these buffers, especially the Post-trigger Buffer.

Record to PC: Check this box if you want the camera to start recording its video feed (when
the event occurs) on the same folder on the same PC as configured on the User Config >
Recording/Snapshot page (if such a folder has been enabled and configured).
Note: The recording will only be as long as the combined Pre- and Post-trigger Buffers (and
for as long as the event trigger is happening – e.g. a motion is detected), so make sure you
enable at least one of these buffers, especially the Post-trigger Buffer.

Network Alarm: Check this box if you want the camera to send a network alarm signal (when
the event occurs) to the CMS servers configured on the Network > Network Alarm page (see
7.3.6 Network Alarm).
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous
settings.
【Pre/Post Trigger Settings】
Pre-trigger Buffer: Select the duration for the buffer. This will determine the amount of footage
(length of time) before the event trigger moment that will be included in an event-triggered video
recording, if that buffer and video recording has been enabled in the Event Configuration Window.
Post-trigger Buffer: Select the duration for the buffer. This will determine the amount of footage
(length of time) after the event trigger moment that will be included in an event-triggered video
recording, if that buffer and video recording has been enabled in the Event Configuration Window.
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous
settings.
63
EAN3120/3220/3300
7.7.2 Motion Detection
Use this page to configure up to four areas in which motion will be detected. When a motion is
detected by the camera, the motion detection icon
will appear at the top right of the
Live page to alert the user. This function can also be linked with correctly configured Events to
trigger Event reactions like the activation of video recording periods, snapshots, alarms, etc.
Color Tabs
: Click on a color tab to turn your mouse cursor into a pen of that color.
You can now create a block of that color on the video screen. Move your cursor to the position
where you want your detection rectangle to start and then click. Move your cursor to the position
(diagonally opposing corner) where you want your detection rectangle to end and then click. The
rectangular area with the selected color will appear. This block will be an area inside which the
camera will detect motion. If you want to create another detection area, use one of the other three
palette colors. Each color denotes a different detection area. Only one block per color is allowed. As
the number of colors suggests, you can configure up to four blocks.
Select All: Click to turn the whole screen into a motion detection area.
Clear All: Click to delete all configured motion detection blocks.
Eraser: Click to turn your mouse cursor into an eraser to delete any block you click on.
Area: Shows the color and number/ID of the block.
Enable: Check this box to enable the related motion detection block.
Sensitivity: Set the sensitivity of the motion detection sensor function.
Click Apply to save all settings Or Cancel to cancel the changes and return to the previous settings.
64
EAN3120/3220/3300
7.7.3 Tamper Detection
Set up a duration time between 10 and 120 seconds. When a tampering event (moved, covered up,
or out of focus) has been detected and the duration reached the setup time, the camera will trigger
the event.
7.7.4 Alarm I/O
Use this page to set the type of trigger input and the type of output contact for the camera’s alarm
channel.
65
EAN3120/3220/3300
7.7.5 Schedule
Use this page to configure a schedule for periods during which the camera should deactivate all
user-activated Events (gray Deselect periods), or when the camera should deactivate all
user-activated Events, except Schedule Recording (SR) events (blue Schedule Recording-only
periods), or when the camera should deactivate only SR events (red Event Recording-only periods),
or when it should enable all activated Events (yellow periods).
Event Recording: Click this button to make every hour block you click on red. A red block represents
an Event Recording-only block, which represents an hour when the camera will deactivate all
preconfigured, activated Schedule Recording events and keep all the other activated events active.
Schedule Recording: Click this button to make every hour block you click on blue. A blue block
represents a Schedule Recording-only block, which represents an hour when the camera will
deactivate all other preconfigured, activated events and keep only the preconfigured, activated
Schedule Recording events active.
Event + Schedule: Click this button to make every hour block you click on yellow. A yellow block
represents an hour in which all activated events, including Schedule Recording events, will be
active.
Deselect: Click this button to make every hour block become grey. A grey block represents an hour
in which all activated events, including Schedule Recording events, will be inactive.
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous
settings.
66
EAN3120/3220/3300
7.8
System
You can set up the system’s time and SD card settings, and to do maintenance and reset actions like
reboots and upgrades.
7.8.1 Date/Time
【Machine Name Settings】If required, enter a new name for the machine. This name will be visible
in the Machine Name field of the IP Utility software, which is included in the software CD.
【Set Time Zone】Set the time zone of the camera’s location.
【Set Date/Time Manually】Set the date/time here if you won’t be using an NTP server to update the
date/time (see below).
【Set Date/Time Sync.】Enter the Network Time Protocol server, if applicable. The camera’s time will
be automatically adjusted by synchronizing with the NTP server.
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous settings.
67
EAN3120/3220/3300
7.8.2 Daylight Saving
Click Enable Daylight Saving to enable this schedule, and select the dates when the region’s
daylight saving period begins and ends.
7.8.3 SD Card
Use this page to prepare the system for safely removing the SD Card from its slot.
【Setup SD Card】
Notification: Select the percentage of storage space that should be left on the card before the
camera notifies you of the impending storage shortage or overwrite.
Event Recording: Select the location where you want the camera to send the impending storage
shortage text notification to.

FTP back Up Only: Select to send the impending storage shortage text notification to the FTP
server entered in the Set FTP Server (see 7.3.3 SMTP/FTP).
68
EAN3120/3220/3300


Event Recording: Select to send the impending storage shortage text notification to the
checked locations in the Notification Over list (see 7.7.1 Event Settings).
Both: Select to send the impending storage shortage text notification to the FTP server and
checked locations.
Overwrite: Click ON if you want the card to start writing over recorded footage when its memory is
full. Click OFF if you want the card to stop recording new footage when its memory is full.
【SD Card Utility】
Capacity: This shows you how much card memory has been used and how much memory capacity
remains on the card.
Remove: Click this button before removing the card from the system.
Format: Click this button to format the card. All data saved on the SD card will be removed if the
card is formatted.
69
EAN3120/3220/3300
7.8.4 Maintenance
【Maintenance Server】
Reboot: Click this button to reboot the unit without changing any of the settings. Use this function if
the unit is not behaving as expected.
Restore: Click this button to restart and reset most of the current settings to their factory default
values. The only settings that will not be changed to default are:
• IP settings
• DDNS settings
Default: The Default button should be used with caution. Pressing this button will return all of the
camera's settings, including the IP address, to the factory default values. The camera will then have
to be reconfigured.
【Save Configuration Server】
Save: To make a backup file of the machine’s current configurations, click Save to save all the
configurations to a config. file. This will enable the user to reload these configuration settings if the
settings are changed and there is unexpected behavior.
【Load Configuration Server】
Select Video to apply only the video parameters from the configuration file to the system. Select
Network to apply only the network parameters from the configuration file to the system. Select All
to apply all the parameters from the configuration file to the system.
Browse: Click the Browse button to locate the saved config. File.
70
EAN3120/3220/3300
Load: Click the Load button to restore the system based on the selected parameters (Video, Network
or All).
【Video Format】Select NTSC or PAL for your local scanning system. Click Apply to save the setting.
【Upgrade Firmware】Click the Browse button to find a previously prepared firmware upgrade file.
Click Upgrade to install the new firmware.
Note:
1. Do not disconnect power to the unit during the upgrade sequence. The unit will reboot
automatically after the upgrade has completed (1-5 minutes).
2. During the upgrade process, all event recording actions will be stopped. Event recording
actions will resume after the camera is rebooted.
3. If the “File Error, Please re-login!!” warning message appears when upgrading the firmware,
please try the following instructions:
a. Go to Internet Explorer > Tools > Internet Option > Security > Custom.
b. Find and enable the Include local directory path when uploading files to a server.
71
EAN3120/3220/3300
8. Upgrading Firmware Using IP Utility
You can upgrade the Firmware using the IP Utility software included in the software CD.
1.
Install and then start the IPU program
, the following IPU window appears. The IPU will
automatically search the IP devices connected in the LAN.
2.
Log in the camera by checking the desired model and then click the Log in
dialog box appears.
icon. The Log in
3.
Type the Username and Password. Click the OK button, the Login status displays.
Note:
1. The default user ID is user1 and the default password is 11111111.
2. If you select more than one camera that has the same user ID / password, you will be able
to log in several cameras at once.
3. Up to 10 cameras can be simultaneously upgraded to the latest firmware. If you connect
the cameras to a PoE switch, please make sure the Power Consumption of the PoE switch
is sufficient.
72
EAN3120/3220/3300
4.
Click the Upgrade Firmware button
, a browsing window appears.
5.
Select the firmware file (.evb) and then click Open. The IPU will automatically upgrade the
firmware. The camera will reboot once the upgrade process is complete.
73
EAN3120/3220/3300
9. Specifications
Model
EAN3120
EAN3220
EAN3300
Camera
Image Sensor
1/3" Panasonic CMOS
Megapixel
1.3 MP
Min. Illuminations
Color: 0.1 lux at F1.2
B/W: 0.02 lux at F1.2
Electronic Shutter (Sec.)
4.25 ~ 1/60,000
Scanning System
NTSC / PAL
WDR
Yes
BLC
Yes
Gain Control
Yes
White Balance
Yes
1/2.8" Sony CMOS
2 MP
3 MP
2 ~ 1/50,000
1 ~ 1/10,000
Yes
No
Lens
Mounting Type
C / CS
Day / Night
Yes (with removable auto IR-cut filter)
IRIS Control
DC Electrical IRIS / Lens IRIS
Video
Video Compression
H.264 / MJPEG
NTSC
2048 x 1536, 1920 x 1200 (for EAN3300 only)
1920 x 1080 (for EAN3300 / 3220 only)
1280 x 1024, 1280 x 720, 1024 x 768, 720 x 480, 704 x 480, 640 x 480,
352 x 240, 320 x 240, 160 x 120
PAL
2048 x 1536, 1920 x 1200 (for EAN3300 only)
1920 x 1080 (for EAN3300 / 3220 only)
1280 x 1024, 1280 x 720, 1024 x 768, 720 x 576, 704 x 576, 640 x 480,
352 x 288, 320 x 240, 160 x 120
Resolution
Frame Rate
30 fps at 1280 x 1024
30 fps at 1920 x 1080
Audio
Audio Streaming
Two-way audio
Audio Compression
G.711
74
15 fps at 2048 x 1536
EAN3120/3220/3300
Network
Interface
10 / 100 Base-T Ethernet, RJ-45 socket
Supported Protocols
TCP/IP, IPV6, UDP, ICMP, DHCP, NTP, DNS, DDNS, SMTP, SNMP, FTP,
HTTP, HTTPs, PPPoE, UPnP, Bonjour, RTP, RTSP, RTCP, IGMP, ARP, ONVIF,
PSIA
Connector
Power
DC female port / PoE
Ethernet
RJ-45
Audio
1 In (Line-in 3.5mm stereo TRS jack)
1 Out (phone jack for Speaker)
Alarm I/O Terminal
I/O wires
Local Storage
Micro SD / SDHC memory card slot
TV-Out
Test output socket, composite 1 V p-p / 75 Ω
General
Power Source
12 VDC / PoE (IEEE802.3af Class 3)
Power Consumption
(IR LEDs On)
5W (12 VDC)
6.21W (PoE)
Operating Temperature
0°C ~ +50°C / 32°F ~ +122°F
Humidity
20% to 80% (no condensation)
Safety
CE, FCC
Dimensions (L x W x H)
118 x 56 x 68 mm / 4.6 x 2.2 x 2.6 in
Weight
410 g / 0.9 lb
Language
Czech, Dutch, English, French, German, Japanese, Polish, Portuguese,
Russian, Simplified Chinese, Spanish, Traditional Chinese
5W (12 VDC)
5.22W (PoE)
75
5W (12 VDC)
5.36W (PoE)
EAN3120/3220/3300
10. Troubleshooting
Error messages pop up
A. When these error messages pop up, follow the steps below to fix the problem.
1. To enter the Registry Editor of your computer: Click Start and type “regedit” in the Search Program and
Files field.
2. Click the Enter button, the Registry Editor window appears.
76
EAN3120/3220/3300
3. Find the KeepAlive Timeout Dword by following the path:
\HKEY_CURRENT_USER\Sofware\Microsoft\Windows\CurrentVersion\Internet Settings
4. Double-click KeepAlive Timeout and this window appears.
5. Change the Value data to 480000 and click OK.
77
EAN3120/3220/3300
B. Snapshot / Record error message.
For Microsoft IE10 and above users, you may have the above error message pop up when you click the
Snapshot
or Record
button on the Live View window. You can simply solve this
problem by setting up your Microsoft Internet Explorer to Run as administrator.
78
EverFocus Electronics Corp.
EverFocus Taiwan:
12F, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, Taipei, Taiwan
TEL: +886 2 2698 2334
FAX: +886 2 2698 2380
www.everfocus.com.tw
marketing@everfocus.com.tw
EverFocus Europe - Germany:
Albert-Einstein-Strasse 1, D-46446
Emmerich, Germany
TEL: +49 2822 93940
FAX: +49 2822 939495
www.everfocus.de
sales@everfocus.de
EverFocus China - Beijing:
Room 609, Technology Trade Building,
Shangdi Information Industry Base,
Haidian District, Beijing 100085, China
TEL: +86 10 6297 3336~39
FAX: +86 10 6297 1423
www.everfocus.com.cn
marketing@everfocus.com.cn
EverFocus China - Shenzhen:
4F, No. 2, D4 Building, Wan Yelong
Industrial Park, Tangtou Road, Shiyan,
Baoan, Shenzhen, Guangdong 518101, China
TEL: +86 755 2765 1313
FAX: +86 755 2765 0337
www.everfocus.com.cn
marketing@everfocus.com.cn
EverFocus USA - California:
1801 Highland Avenue, Unit A, Duarte, CA 91010, USA
TEL: +1 626 844 8888
FAX: +1 626 844 8838
www.everfocus.com
sales@everfocus.com
EverFocus USA - New York:
415 Oser Avenue, Unit S, Hauppauge, NY 11788, USA
TEL: +1 631 436 5070
FAX: +1 631 436 5027
www.everfocus.com
sales@everfocus.com
EverFocus Japan:
5F, Kinshicho City Building, 2-13-4 Koto-Bashi,Sumida-Ku,
Tokyo, 130-0022, Japan
TEL: +81 3 5625 8188
FAX: +81 3 5625 8189
www.everfocus.co.jp
info@everfocus.co.jp
EverFocus Europe - UK:
Unit 12, Spitfire Business Park,
Hawker Road, Croydon Surrey, CR0 4WD, UK
TEL: +44 20 8649 9757 / +44 845 430 9999
FAX: +44 20 8649 9907
www.everfocusuk.co.uk
salesuk@everfocus.com
EverFocus India:
Suite 803, Housefin Bhavan, C-21,
Bandra Kurla Complex, Bandra (East),
Mumbai 400051, India
TEL: +91 22 6128 8700
FAX: +91 22 6128 8705
www.everfocus.in
sales@everfocus.in
Your EverFocus product is designed
and manufactured with high quality
materials and components which can
be recycled and reused.
This symbol means that electrical and
electronic equipment, at their
end-of-life, should be disposed of
separately from your household
waste.
Please, dispose of this equipment at
your local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Ihr EverFocus Produkt wurde entwickelt
und hergestellt mit qualitativ
hochwertigen Materialien und
Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte am
Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!
P/N: 4605PQ3120B010A-Ver.F
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising