EverFocus | EZN3261 | Owner Manual | Everfocus EZN3261 Owner Manual

Everfocus EZN3261 Owner Manual
EZN Series Outdoor IR Bullet IP Camera
10x Optical Zoom, Auto Focus, True Day/Night, WDR, IP66
User’s Manual
Copyright © EverFocus Electronics Corp.
Release Date: November, 2015
Copyright  1995-2015 EverFocus Electronics Corp.
All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form or by
any means without written permission of the EverFocus Electronics Corporation.
EverFocus
12F, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, Taipei, Taiwan
TEL: +886 2 2698 2334
FAX: +886 2 2698 2380
www.everfocus.com.tw
November, 2015
EZN3261/3361
About this document
All the safety and operating instructions should be read and followed before the unit is operated. This
manual should be retained for future reference. The information in this manual was current when
published. The manufacturer reserves the right to revise and improve its products. All specifications are
therefore subject to change without notice.
Regulatory Notices
FCC Notice "Declaration of Conformity Information"
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications made to this equipment, not expressly approved by EverFocus or
parties authorized by EverFocus could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
EverFocus Electronics Corp.
12F, No. 79, Sec. 1, Shin-Tai Wu Rd., Hsi-Chi,
Taipei Hsien, Taiwan, R.O.C.
EZN Series cameras comply with CE and FCC.
i
Precautions
1. Do not install the camera near electric or magnetic fields.
Install the camera away from TV/radio transmitters, magnets, electric motors, transformers and
audio speakers since the electromagnetic fields generated from these devices may distort the video
image or otherwise interfere with camera operation.
2. Never disassemble the camera beyond the recommendations in this manual nor introduce
materials other than those recommended herein.
Improper disassembly or introduction of corrosive materials may result in equipment failure or other
damage.
3. Try to avoid facing the camera toward the sun.
In some circumstances, direct sunlight may cause permanent damage to the sensor and/or internal
circuits, as well as creating unbalanced illumination beyond the capability of the camera to
compensate.
4. Keep the power cord away from water and other liquids and never touch the power cord with wet
hands.
Touching a wet power cord with your hands or touching the power cord with wet hands may result
in electric shock.
5. Never install the camera in areas exposed to oil, gas or solvents.
Oil, gas or solvents may result in equipment failure, electric shock or, in extreme cases, fire.
6. Cleaning
For cameras with interchangeable lenses, do not touch the surface of the sensor directly with the
hands. Use lens tissue or a cotton tipped applicator and ethanol to clean the sensor and the camera
lens. Use a damp soft cloth to remove any dirt from the camera body. Please do not use complex
solvents, corrosive or abrasive agents for cleaning of any part of the camera.
7. Do not operate the camera beyond the specified temperature, humidity or power source ratings.
Use the camera at temperatures within -40°C ~ 55°C / -40°F ~ 131°F (12 VDC) or -20°C ~ 55°C / -4°F ~
131°F (PoE), and humidity between 20% and 80%; this device is not rated as submersible. The input
power source is 12VDC / PoE. Be sure to connect the proper + / - polarity and voltage, as incorrect
polarity or too high a voltage will likely cause the camera to fail, and such damage is not covered by
the warranty. The use of properly fused or Class 2 power limited type supplies is highly
recommended.
8. Mounting
Use care in selecting a solid mounting surface which will support the weight of the camera plus any
wind, snow, ice or other loading, and securely attach the camera to the mounting surface using
screws and anchors which will properly support the camera. If necessary (e.g. when mounting to
drop ceilings) use a safety wire to provide additional support for the camera.
ii
TABLE OF CONTENTS
1. Introduction ..................................................................................................................................... 1
2. Features ........................................................................................................................................... 2
3. Physical Description ......................................................................................................................... 3
3.1
Cables ........................................................................................................................................... 3
3.2
5-Axis Button ............................................................................................................................. 4
4. Installation ....................................................................................................................................... 5
4.1
Packing List ................................................................................................................................. 5
4.2
Basic Installation ...................................................................................................................... 6
4.2.1
Mounting and Wiring ............................................................................................... 6
4.2.2
Inserting a Micro SD Card....................................................................................... 9
5. Accessing the User Interface ........................................................................................................... 10
5.1
Checking the Dynamic IP Address................................................................................................ 10
5.2
Settings for Microsoft Internet Explorer...................................................................................... 14
5.3
Connecting the Camera to the Network...................................................................................... 16
5.4
Live View Window........................................................................................................................ 18
6. Playback ......................................................................................................................................... 22
6.1
Remote Playback Using Playback Page ........................................................................................ 22
6.2
Setting Up the Playback Function ................................................................................................ 24
6.3
6.2.1
Inserting / Removing the Micro SD Card ................................................. 24
6.2.2
Testing the Playback Function .................................................................. 25
Playing Back Using ARV Viewer ................................................................................................... 27
7. Settings .......................................................................................................................................... 28
7.1
System Settings ............................................................................................................................ 29
7.1.1
Network ..................................................................................................... 29
7.1.2
Date / Time ................................................................................................ 35
7.1.3
Storage ....................................................................................................... 36
7.1.4
Display and Overlay .................................................................................. 38
7.1.5
System Maintenance ................................................................................. 40
7.1.6
System Information ................................................................................... 43
7.1.7
User ............................................................................................................ 44
iii
7.1.8
7.2
7.3
7.4
Black/White List ........................................................................................ 46
Camera Settings ........................................................................................................................... 47
7.2.1
Streaming and Audio ................................................................................. 47
7.2.2
Profile ........................................................................................................ 50
7.2.3
Camera ....................................................................................................... 52
7.2.4
Schedule ..................................................................................................... 55
7.2.5
Image .......................................................................................................... 56
Event Settings .............................................................................................................................. 57
7.3.1
Event Wizard .............................................................................................. 57
7.3.2
Event .......................................................................................................... 58
7.3.3
Notification ................................................................................................ 62
Link to Smart Phone App ............................................................................................................. 65
8. Upgrading Firmware Using IP Utility ............................................................................................... 66
9. Specifications ................................................................................................................................. 68
10.
Troubleshooting .......................................................................................................................... 70
Appendix .............................................................................................................................................. 73
A. Tested Card Brands............................................................................................................................. 73
B. Enabling the Multicast Function ......................................................................................................... 74
C. RTSP URL Syntax ................................................................................................................................. 76
D. Setting up Port Forwarding Function ................................................................................................. 77
E. Setting up DDNS Function .................................................................................................................. 79
iv
EZN3261/3361
1.
Introduction
The EZN series bullet IP camera comes with two models: 2 MP and 3 MP, providing up to 30 fps at
2048 x 1536 viewing resolution. Equipped with an auto focus 10x optical zoom lens, the series can provide
the desired field of view with superior video quality in precision focus.
The EZN series supports quad streams from H.264, MPEG4 or MJPEG. Featured with a weather-resistant
(IP66) housing plus 12 IR LEDs for enabling the night visibility of up to 40 meters, the cameras meet a wide
variety of needs for outdoor surveillance.
The EZN series bullet IP camera features the Wide Dynamic Range (WDR) function, which can provide clear
images even under back light circumstances where intensity of illumination can vary excessively. The DNR
(Digital Noise Reduction) function is designed for reducing the noises in the images, allowing the camera to
better distinguish between real motion and image noise, and thus results in a possibility to store more
video evidence on the connected storage devices.
A built-in micro SDHC card slot and Power over Ethernet (IEEE802.3at Class 4) features are also provided.
You can power the camera over the network or by connecting the camera to a 12VDC power supply. Since
the series conforms to ONVIF / PSIA for compatibility with other network video devices, it interoperates
with a wide variety of hardware and software systems. You can also use EverFocus Mobile Applications to
remotely view the live views of the cameras through your handheld devices; or use EverFocus CMS to
remotely manage multiple IP devices connected on the network. The EZN series bullet IP camera is the
ideal solution for your outdoor surveillance needs.
The EZN Series Models
Model Name
Megapixel
10x Optical Zoom
Auto Focus
WDR
EZN3261
2 MP
Yes
Yes
Yes
EZN3361
3 MP
Yes
Yes
Yes
System Requirement
Before installing, please check that your computer meets these system requirements.
•
•
Operating System: Microsoft Windows XP / Vista (32-bit) / 7 (32-bit)
Microsoft Internet Explorer 7 or above
Note: For using the Internet Explorer, some settings are required. Please refer to 5.2 Settings for
Microsoft Internet Explorer.
1
EZN3261/3361
2.
Features
•
•
•
1/3” Progressive scan CMOS
Quod streams from H.264, MPEG4 or MJPEG
Up to 30 fps at 1920 × 1080 (EZN3261)
Up to 30 fps at 2048 x 1536 (EZN3361)
•
•
•
•
•
•
•
•
•
•
•
10x Optical Zoom
10x Digital Zoom
Auto Focus
Extended IR range of up to 40-meter / 131-foot with 12 LEDs
Weather-resistant (IP66)
Hallway Display (9:16)
Built-in micro SD / SDHC card slot (see Appendix for the tested card brands)
True Day/Night functionality with automatic IR filter operation
Split glass to prevent internal IR reflections
Cable management for protecting the cable within the bracket
E-Z lock ring at the base is designed with easy to grip tabs to firmly clamp the camera in place, plus a
set screw for security
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
BNC video output to simplify the on-site installation and verification
3-axis mechanism (pan / tilt / rotate)
One alarm input and output
Two-way audio
Multiple profiles for image settings
Wide Dynamic Range (WDR)
Digital Slow Shutter (DSS)
2D / 3D Dynamic Noise Reduction (DNR)
Motion Detection
Privacy Mask
Anti-Tampering
Setup wizard for easy Web UI setting
Endurable to low environment temperatures (-40°C ~ 55°C / -40°F ~ 131°F)
12 VDC / PoE
Multi-languages on Web interface
ONVIF compliant
Supports EverFocus CMS and Mobile Applications (iOS / Android)
2
EZN3261/3361
3.
Physical Description
1
2
3
4
No.
1
2
Name
Light Sensor
IR LEDs
3
Video Test Output
4
5-Axis Button
5
6
Micro SD / SDHC Slot
Lens
7
Camera Cover
8
Sunshield
3.1
5
6
7
8
Description
Detects lights.
12 IR LEDs for infrared illumination in night vision applications.
Connects to a handheld test monitor for adjusting camera focus / zoom
/ angles.
For adjusting camera focus / zoom or restoring the camera to the
factory default. See 3.2 5-Axis Button for more details.
Insert a micro SD / SDHC card (see Appendix A for tested card brands).
10x optical zoom, auto focus, DC Iris, F1.8-360C.
Remove the cover for using the 5-Axis Button, inserting a micro SD card
or connecting to a handheld test monitor.
Protect the camera from the direct rays of the sun.
Cables
The Cables provide connections for Network, power, audio input / output and alarm input / output.
Note that the audio cables feature a line 3.5mm jack (TRS). Be sure to prepare speakers / microphones
with TRS connector (see TRS Connector image below). Also, speakers / microphones with a (built-in)
amplifier and external power supply are required.
Pin Assignment for Alarm Input / Output
Alarm Input / Output
Audio-In (TRS Line-in) (Pink)
Audio-Out (TRS Line-out) (Green)
12 VDC Input
LAN / PoE Cable
4 3 2 1
3
Pin 1: Alarm GND (-)
Pin 2: Alarm In (+)
Pin3: Alarm COM (-)
Pin4: Alarm Out (+)
EZN3261/3361
TRS Connector
To activate the Audio function, the Enable Audio must be
checked. See Audio Settings in 7.2.1 Streaming and Audio.
Ground (Sleeve)
Right Channel (Ring)
Left Channel (Tip)
3.2
5-Axis Button
The 5-Axis Button is designed for manually adjusting zoom and focus, and restoring to factory default.
You can also use the button to auto focus.
Note: If you have already inserted a desiccant bag inside the module, close the cover immediately in
case of reducing the absorption capacity of the desiccant bag inside the camera. To replace a new
desiccant bag, see Step3 in 4.2.2 Inserting a Micro SD Card.
Up
Left
Right
Down
Focus: Push the button left or right.
Zoom: Push the button up or down.
Auto Focus: Press the button once.
Reset: Press and hold the button for 5 seconds.
Note that if you select Auto from the Focus Mode drop-down list in the Lens Settings field (see 7.2.3
Camera), the camera will automatically adjust focus every time you push the button up or down to
zoom.
4
EZN3261/3361
4.
Installation
4.1
Packing List
Please check that there is no missing item in the package before installing.
•
•
•
•
•
EZN Series Camera x 1
• 4-Pin Terminal Block x 1
Quick Mounting Ring x 1
• Test-Out Cable x 1
RJ-45 Connector x 1
• Software CD x 1
Desiccant Bag x 1
• Quick Installation Guide x 1
Mounting Kit x 1
- Long Screw x 4 (for attaching the Quick Mounting Ring to the mounting surface)
- Short Screw x 4 (for connecting the Camera Base to the Quick Mount Ring)
- Screw Anchor x 4 (in conjunction with Long Screw)
- Hexagon Key x 1 (for adjusting the camera position)
- Hexagon Wrench x 1 (for screwing the set screw)
- Plug x 1 (inserting to the Quick Mounting Ring for through-the-wall installation)
Note:
1. Equipment configurations and supplied accessories vary by country. Please consult your local
EverFocus office or agents for more information. Please also keep the shipping carton for possible
future use.
2. Contact the shipper if any items appear to have been damaged in the shipping process.
5
EZN3261/3361
4.2
Basic Installation
This section will introduce the basic installation on mounting / wiring the camera, inserting a micro SD
card and adjusting camera angles.
4.2.1 Mounting and Wiring
Follow the steps below for mounting and wiring the camera.
1.
Before screwing the camera to the wall, drill four holes on the wall according to the hole-positions
on the supplied Quick-Mounting Ring. If you wish to run the wires through the wall, drill another
hole in the middle of the circular area within the Quick-Mounting Ring.
This conduit Is for wiring the cables along
the wall installation.
Plug
Circular Area
If you want to wire the cables through the wall,
then this conduit will not be used. You can
insert the supplied Plug into the conduit.
2.
Push the four supplied Anchors into the four holes on the wall. Place the Quick-Mounting Ring
against the anchoring surface so that the holes line up. Screw the Quick-Mounting Ring to the wall
using the supplied Long Screws.
Long Screws
Quick-Mounting Ring
Anchors
Wall
6
EZN3261/3361
3.
Screw the Camera Base to the Quick-Mounting Ring using the supplied four Short Screws.
Camera Base
Quick-Mounting Ring
Short Screws
Short Screws
You can wire the cables from the side of the camera or through the wall.
Wire the cables from the side
of the camera
Wire the cables through the wall
4.
Connect the network, power and other cables to the related devices. Please refer to 3.1 Cables.
5.
Optionally insert a micro SD / SDHC card into the card slot (see 4.2.2 Inserting a Micro SD Card).
Note: After opening the camera cover for inserting the micro SD card, you have to stick the
applied desiccant bag inside the camera.
6.
Access the camera live view. Please see 5. Accessing the User Interface. Or connect a handheld test
monitor to the Video Test Output on the camera module for adjusting camera focus/zoom/angles.
For details on how to adjust camera focus / zoom using the 5-Axis Button on the camera module,
see 3.2 5-Axis Button.
7
EZN3261/3361
7.
Adjust the camera angles.
Pan Adjustment: Unscrew the Set Screw using the supplied Hexagon Wrench. Twist the Camera
Base forcefully until it unscrews from the E-Z Lock Ring. Rotate the camera by 360° to the desired
position and screw the E-Z Lock Ring until it locks against the Camera Base. Screw back the Set
Screw.
Set Screw
E-Z Lock Ring
Camera Base
360°
Tilt Adjustment: Loosen the Tilt Screw using the provided Hexagon Key and adjust the tilt angle by
90°.
Tilt Screw
90°
Rotational Adjustment: Loosen the Rotate Screws on both side of the camera body using the
providing Hexagon Key and rotate the camera by 360° (180° to the left / 180° to the right).
Rotate Screw
180°
180°
8
EZN3261/3361
4.2.2 Inserting a Micro SD Card
You can optionally insert a micro SD card into the card slot on the camera module for recording videos.
Please refer to Appendix for the tested card brands.
1. Loosen the Set Screw on the Sunshield using the provided Hexagon Wrench and then slide the
Sunshield out from the rail on the camera.
Sunshield
Set Screw
2. Rotate and then remove the camera cover, and insert a micro SD card into the card slot.
Micro SD Card Slot
3. Stick the supplied Desiccant Bag inside the camera.
Note: It’s recommended to close the cover immediately in case of reducing the absorption
capacity of the desiccant bag inside the camera.
4. Firmly close the camera cover for waterproofing, slide the Sunshield back to the camera body and
then screw the Set Screw.
9
EZN3261/3361
5.
Accessing the User Interface
This section explains how to access the Web interface of the camera for configuration.
5.1
Checking the Dynamic IP Address
You can look up the IP address and access the Web interface of the IP camera using the IP Utility (IPU)
program, which is included in the software CD. The IP Utility can also be downloaded from EverFocus’
Website: http://www.everfocus.com/HQ/Support/DownloadCenter_p1.aspx. Please connect the IP
camera on the same LAN of your computer.
1.
Save IP Utility Setup .exe
in your computer. Double click the .exe file and follow the on‐screen
instructions to install the IP Utility.
2.
Click the Finish button, the IP Utility will be automatically launched to search the IP devices
connected on the same LAN.
10
EZN3261/3361
3.
To access to the Live View window, double click the IP address of the desired device, the login
window pops up. Type the user ID and password to log in. By default, the user ID is user1 and the
password is 11111111.
4.
Click OK, the Live View window appears.
Note:
1. You might be required to install IPNetMediaOCX add-on, If asked, click Install.
2. If you have difficulties viewing live view or upgrading firmware, you may need to check your
computer settings. Please refer to 5.2 Settings for Microsoft Internet Explorer in the User’s
Manual.
5.
To optionally configure the Machine Name, IP Address, IP Type or Port Number using the IPU:
a. Log in the device by checking the desired model and then click the Log in
icon. The Log in
dialog box appears.
b. Type the Username and Password and click OK. The status column will display Login.
Note:
1. The default user ID is user1 and the default password is 11111111.
2. If you select more than one camera that has the same user ID / password, you will be
able to log in several cameras at once.
11
EZN3261/3361
c. Right click the column to configure the setting. Click Apply Changes
button to apply and save
the settings.
Note:
1. Most networks uses DHCP to assign IP address, if you are unsure of your network
settings, please consult your network administrators for configuration details.
2. If you want to set up PPPoE, please refer to 6.1.1 Network.
To set up a static IP:
By default, EverFocus’ IP cameras are set up with DHCP. To change the IP setting to static IP, select
Static from IP Type drop-down list and set up the desired IP Address, for example, 192.168.31.67
Please also set up the Subnet Mask and Gateway. Click the Apply Changes button to apply and save
the settings.
To show the Subnet Mask and Gateway items on the title bar, right click the title bar to display the
Customize Columns window, select Subnet Mask and Gateway and then click OK.
12
EZN3261/3361
1
2
3
13
EZN3261/3361
5.2
Settings for Microsoft Internet Explorer
To enable Remote Live View, Firmware Upgrade and ActiveX Prompt on Internet Explorer, some settings
have to be complete. Please follow the steps below:
1.
On the computer, click Start > Control Panel > System and Security > Action Center (click Change
User Account Control Settings), the User Account Control Settings window appears. Adjust the
slide bar to Never Notify and then click OK. Restart your computer if requested.
2.
Open the Internet Explore, click Tools > Internet Options > Security Tab > Custom Level, the
Security Settings windows appears.
14
EZN3261/3361
3.
In the Download unsigned ActiveX controls field, select Prompt. In the Include local directory
path when uploading files to a server field, select Enable. Click OK.
4.
In the Internet Options window, click the Advanced tab and then disable Enable memory
protection to help mitigate online attacks. Click OK.
15
EZN3261/3361
5.3
Connecting the Camera to the Network
There are three methods to connect the IP camera to the network: Router or LAN Connection, Direct
High-Speed Connection and One-to-One Connection.
Router or LAN connection
This is the most common connection in which the IP camera is connected to a router and allows
multiple users on and off site to see the IP camera on a LAN/WAN (Internet). The camera must be
assigned an IP address that is compatible with its LAN. By setting up port forwarding on the router, you
can remotely access the cameras from outside of the LAN via the Internet. To remotely access the Web
interface of the IP camera, please refer to 7.1.1 Network (DDNS). To set up port forwarding, please refer
to Appendix C. Setting up Port Forwarding Function.
Cat 5 Straight Through Cable
Internet
High-speed modem
Straight-through LAN patch cable
Router
Left: Pinout of a straight-through cable.
16
EZN3261/3361
Direct High-Speed Connection
In a Direct High-Speed Connection, the camera connects directly to a modem without the need for a
router. You need to set the static or dynamic WAN IP address assigned by your ISP (Internet Service
Provider) in the camera’s configuration web pages. To access the camera, just type
“http://xxx.xxx.xxx.xxx”, where xxx.xxx.xxx.xxx is the IP address given by your ISP. If you have a dynamic
IP address, this connection may require that you use DDNS for a reliable connection. Please refer to
Appendix D. Setting up DDNS Function.
Internet
Cat 5
Straight Through Cable
High-speed modem
One-to-One Connection (Directly from PC to IP Camera)
You can connect directly without using a switch, router or modem. However, only the PC connected to
the camera will be able to view the IP camera. You will also have to manually assign a compatible IP
address to both the computer and the IP camera. Unless the PC has another network connection, the IP
camera will be the only network device visible to the PC. See the diagram below:
Cat 5
Right: Pinout of a crossed-over cable.
17
EZN3261/3361
5.4
Live View Window
1. Live View
Click the Live View button to display the Live View window. If you experience video feed lag time (if
connected via Internet), you can reduce the resolution or limit the number of streams. See 7.2.1
Streaming and Audio.
2. Playback
Click the Playback button to play back the recorded data directly from the on-camera SD / SDHC
card. For this function to become active, you have to insert an SD / SDHC card into the SD / SDHC
card slot on the camera (see 6.2 Setting up the Playback Function). For the tested card brands,
please refer to Appendix A.
3. Snapshot
Click the Snapshot button to take a snapshot. By default, the snapshot will be saved at
C:\EverFocus\. To change the location, see Record to Local in 7.1.3 Storage.
Note: For Microsoft IE10 and above users, some settings have to be complete to enable this
function (see B. Snapshot/Record error message in 10. Troubleshooting).
18
EZN3261/3361
4. Record
Click the Record button to start / stop recording the current video stream. By default, this icon is
only for one-minute video recording and the recordings will be saved at C:\EverFocus\. To change
the recording time, see File Size in 7.1.3 Storage. To change the location, see Record to Local in
7.1.3 Storage. To record long-period recordings, please set up a recording schedule (7.3.2 Schedule
Settings). To change the source video stream and recording format, see Recording and Snapshot
Settings in 7.1.3 Storage.
Note: For Microsoft IE10 and above users, some settings have to be complete to enable this
function (see B. Snapshot/Record error message in 10. Troubleshooting).
5. Speaker / Microphone
Click the Speaker and Microphone buttons to switch the sound on/off for the speakers and
microphones respectively (if such external devices have been connected to the camera directly or
via the network). To activate the Audio function, the Enable Audio must be selected. See Audio
Settings in 7.2.1 Streaming and Audio. Note that the camera provides a line-in 3.5mm jack (TRS),
therefore, TRS microphones with a (built-in) amplifier and external power supply are required.
6. Setting
Click the Setting button to enter the Settings page (see 7. Settings).
7. Wizard
Click the Wizard button to enter the Setup Wizard.
8. Hallway Display (9:16): Click the Rotate button
to rotate the live image. This function
allows users to monitor vertically-oriented areas such as hallway, corridors and aisles.
19
EZN3261/3361
Note: To achieve the best 9:16 display effect, it’s recommended to:
1. Install the camera sideways by rotating the camera to the left or right by 90°.
Rotate Screw
90°
90°
2.
3.
Select a 16:9 View Size (e.g. 1920x1080 / 1024x768).
Use the Rotate button.
9. Video Stream
Select the Video Stream (Stream 1, Stream 2, Stream 3 or Stream 4) that will be displayed in the live
view window on the bottom. Stream 2, Stream 3 and Stream 4 are only selectable if you have
enabled the stream (see 7.2.1 Streaming and Audio). The default setting is Stream 1 only.
10. View Size
Use this to select the appropriate view size and shape of the live view window on the bottom. A
smaller size might increase transmission speed and video quality.
11. Language
Click the Language drop-down list to select the desired language.
12. Digital Zoom
Click
to zoom in / out the camera view up to 10x. Clicking on a magnified image will
re-center the image around that point.
13. One Push
The One Push button can be displayed on the live view window by enabling the Show One Push
Buttons function in the Live View Layout Settings (see 7.1.4 Display and Overlay). Click the
button to Auto Focus. To enable the Auto Focus button, you have to select Auto in
the Focus Mode drop-down list (see 7.2.3 Camera). When the Auto Focus function is enabled, the
camera will automatically adjust focus every time you click the Zoom in/out buttons.
20
EZN3261/3361
14. Manual Control
Click the
button to trigger an event directly from the Live View window. If you have
configured an event (in the Event List) that will trigger a reaction (like a recording) when a Manual
Trigger event occurs, clicking this button will trigger that reaction. You can select what that reaction
will be. You can, for instance, set the camera to record the audio/video feed to the SD card on
board the camera. You can then click on the Playback button to open the Playback page and search
for and play all such recordings that had been stored on the card. Such event actions will be
effective once they have been configured in the Event List (see 7.3.2 Event).
Click the
button to reset the alarm output remotely.
15. Lens Control
The Lens Control buttons can be hidden on the live view window by disable the Show Lens Control
Buttons function in the Live View Layout Settings (see 7.1.4 Display and Overlay). These buttons
control the lens actions. Click and hold the
icons to continuously focus closer or farther.
Click the
icons to focus one step closer or farther. Click and hold the
icons to
continuously zoom in or zoom out. Click the
icons to zoom in or zoom out one step
forward or backward.
change the focus speed.
: Select between 1X and 4X and then click the
to
Note: If you select Auto from the Focus Mode drop-down list (see Lens Settings image above), the
camera will automatically adjust focus every time you click the Zoom in/out buttons.
16. Status Display (info line that can be placed above video box or at bottom of page)
This shows the name of the camera that is currently active or being configured, current date/time
and current frame rate. You can activate these info displays in the Overlay Text Settings (see 7.1.4
Display and Overlay).
17. Event signal icons (above video screen)
When an alarm or motion event is triggered, a signal icon will appear at the top right of the Live
View window to alert the user.
Alarm event icon
: When an alarm is triggered, this icon appears.
Motion detection icons
: The colors of these motion event icons correspond to
the colors of the motion trigger areas you have configured in the Motion Settings (see 7.3.2 Event).
Recording icon
: When the camera is recording to a PC-based folder, this icon appears.
21
EZN3261/3361
6.
Playback
You can remotely play back the recordings stored in the on-camera micro SD card on the Web interface, or
play back the recordings stored in the computer using the ARV Viewer included in the software CD.
Playback is designed as a quick way to check recent recordings that were triggered by Events that were
configured to “Record to SD Card” in the Event Management (see 7.3.2 Event).
Note: The Playback page is only accessible once the on-camera SD card is inserted and active. Please
refer to Appendix A for the tested card brands.
6.1
Remote Playback Using Playback Page
On the Live View Window, click the Playback button
22
to open the Playback page.
EZN3261/3361
Search by File: Click the Search button to search for all recording files on the on-camera SD card.
Search results will be displayed in the Filename area.
Search by Time: Click the Date / Time column and select the date and time from which you want to
search until the present moment. Click Search to get your search results, which will be displayed in the
Filename area.
Search by Event: Select the type of Event recordings you want to search for (Alarm, Motion, Manual
Trigger) and then click the Start Date / Time; End Date / Time column to select the Start Time
date/time and the End Time date/time of your search. Click Search to get your search results, which
will be displayed in the Filename area.
Multiple Files: Check this box if you want the video player to play all the files in the selected folder. The
files will be displayed in the Filename area.
Loop Again: Check this box if you want the video player to play the selected file over and over again.
Play: Once you have opened the file’s folder and have clicked on the file to highlight it, its details will
be displayed in the File Information area. You can now click Play
Pause: Click
Stop: Click
Snapshot: Click
Zoom In: Click
Zoom Out: Click
to play that specific file.
to pause playing back.
to stop playing back.
to take a snapshot.
to zoom in.
to zoom out.
Filename: This area will display a list of search results (recording files and folders). Folders (named with
the recorded date) will be displayed first. Click on the folder and click on each subfolder until the
recording files (.arv) in that folder is listed.
File Information: Click a file on the Filename list, the selected file information will be listed.
Copy: Click to copy the selected file to the computer-based folder of your choice. A browsing box will
open so that you can search for the folder of your choice. You can use the ARV Viewer to play back the
recordings recorded in your computer. For details on ARV Viewer, see 6.3 Playing Back Using ARV
Viewer.
Lock: Click to lock the selected file. This will protect that file from being overwritten during any
overwrite procedure. The file will thus be saved on the micro SD card indefinitely. However, the file will
still be deleted if the micro SD card is ever formatted.
Remove: Click to delete the selected file.
23
EZN3261/3361
6.2
Setting Up the Playback Function
Note that the Playback function will not be active until the user has inserted a micro SD card in the
camera’s micro SD card slot. The card may also have to be formatted in the Secure Digital Card field (see
7.1.3 Storage). For the tested card brands, please refer to Appendix A.
Micro SD Card Slot
6.2.1 Inserting / Removing the Micro SD Card
1.
To insert the SD card: Remove the camera cover and insert the SD card into the SD card slot
before powering on the camera.
2.
To remove the SD card: Click the Remove button (System Settings > Storage > Secure Digital Card)
when the camera is powered on, the SD card information “SD card is not mounted” will display
and the Remove button will change to Attach, and then you may remove the SD card. If you
want to insert the SD card again, insert the SD card and then click the Attach button.
After inserting the SD card into the SD card slot, the Playback button on the Live View page should be
activated. If not, do the following:
1.
Click the Remove button, pull the card out and re-insert it.
2.
Click the Format button to format the card. NOTE: All data on the disk will be deleted if the
Format button is clicked.
24
EZN3261/3361
6.2.2 Testing the Playback Function
1. To test the Playback function (this is not required), set up a “Manual Trigger” Recording Event by
clicking Event Settings > Event.
2. Give the event a name, like “Test 1”.
3. In the “Event Triggered Type” field, click on Manual Trigger.
4. Below this, check “Enable This Event”, “Enable Post-trigger Buffer”, and “Record to SD Card”.
5. To save your settings, click the Create button, and the Event will be listed in the Event List.
6. Look at the “Post-trigger Buffer” at the bottom to make sure the buffer time is set to 10 seconds.
Click the Apply button.
25
EZN3261/3361
7. Click the LiveView button to go back to the Live View page.
8. Get ready to click the Trigger Event button on the Live View page. Before you do, see if you can
find something in the view screen that will give you a visual time marker. For instance, if you can
get your hand in front of the camera’s lens, get ready to count down on your fingers.
9. Click the Trigger Event button and slowly count down on your fingers in front of the lens (if you are
able to do so – if not, try to find visual cues on the view screen that will help you to mark the
moment you pushed the trigger). The recording period will be as long as the buffer time you
selected – the default period is 10 seconds.
10. Click the Playback button to open the Playback page.
11. There are different ways to search for recording files on the camera’s micro SD card (i.e. the
Playback memory). For a recent recording like your test event, simply click the “Search” button
under the “Show All Files on SD Card” header.
12. If the micro SD card is active and formatted correctly, the recording folder’s name (the recording
day’s date) will appear in the Filename area. Click on this folder to open it. If there are sub-folders,
click on the bottom one (the most recent would be at the bottom) until you can click on a file that
cannot open to another sub-level and shows data in the File Information area to the right. This
would be the file of the most recent recording event.
13. To play this file, click the Play button below the video box. The test footage you have recorded
should start playing. Play time should be 10 seconds if you left the Post-trigger Buffer as 10
seconds.
26
EZN3261/3361
6.3
Playing Back Using ARV Viewer
You can play back the recordings stored in the computer using the ARV Viewer
included in the
software CD. To store the recordings in the computer, please refer to Copy in 6.1 Remote Playback
Using Playback Page.
4
5
6
3
2
1
7
8
9
10
No.
Item Name
Descriptions
1
Snapshot
Click to take and save a snapshot.
2
Load File
Click to load the recordings for playing back.
3
Convert ARV to AVI
Convert the recording from ARV format to AVI format.
4
Playback Time
Display the playback time.
5
Total Time of Recording
Display the total time of the recording.
6
Stop
Click to stop playing the recording.
7
Step Reverse
Click to display the previous frame.
8
Play
Click to play back the recording.
9
Pause
Click to pause the recording.
10
Step Forward
Click to display the next frame.
27
EZN3261/3361
7.
Settings
Click the Setting button
on the Live View Window to enter the setting submenu. There are two tabs:
Basic and Advanced on the left-side bar. You can set up the basic camera settings in the Basic tab. To
further set up comprehensive camera settings, click the Advanced tab, which includes all the settings to be
configured. The chapters below describe the detailed information of the Advanced tab.
28
EZN3261/3361
7.1
System Settings
7.1.1 Network
29
EZN3261/3361
【Protocol Settings】You can transmit the data stream from the IP cameras using the RTSP (Real Time
Streaming Protocol) on the network. The RTSP is a protocol that allows you to access video streams
by using the compatible media players. Click Apply to apply the changes or Cancel to cancel the
changes and return to the previous settings.
 RTP over UDP: The RTSP protocol uses UDP for camera data stream transmission.
 RTP over TCP: The RTSP protocol uses TCP for camera data stream transmission.
 RTP over HTTP: The RTSP protocol uses HTTP for camera data stream transmission.
 Nevio CGI: This is EverFocus’ protocol designed for EverFocus’ IP devices. Select this protocol for
camera data stream transmission.
【IP Settings】Enter the IPv4 / IPv6 details in this area, which applies to your system. Click Apply to
apply the changes or Cancel to cancel the changes and return to the previous settings.
 IPv4:
IP Mode: Refer to the network administrator for these settings of the server. Default: DHCP.
 DHCP: This setting lets the system use an automatically assigned (dynamic) IP address. This
address can change under certain circumstances. For instance, when the camera’s network
switch/hub has to be rebooted. Do not assign to the DHCP server the same IP addresses used
for the other network cameras and PCs with unique IP addresses.
 Static IP: The user can manually set the Static IP address. This type of address is stable and
cannot change, but the user has to make sure there are no address conflicts with other
network-connected devices.
 PPPoE: This is a DSL-connection application. The ISP will ask the user to input a username
and password. Contact your ISP for these details.
Note: If PPPoE is selected as the IP type, the supplied IP Utility program will not be able to
detect the device.

IP address: When DHCP is not used, the user needs to manually enter the IP address of the
camera. Do not enter an IP address that is already used for your computer or other network
cameras.
Subnet Mask: This field is used to set the subnet mask for your network, so that the IP camera
will be recognized within the network. Example: 255.255.255.0. When DHCP is selected, the
DHCP server will assign this value automatically.
Gateway: This field is used to set the gateway for your network so that the IP camera will be
recognized within the network. When DHCP is selected, the DHCP server will assign this value
automatically.
Primary DNS: Enter the IP address of the DNS server if this is provided by an ISP.
Secondary DNS: If your ISP provided you with a secondary DNS address, please enter it here.
Username: Enter the account’s username (used only for PPPoE).
Password: Used only for PPPoE.
IPv6: Enter the IPv6 details in this area, if this applies to your system.
30
EZN3261/3361
【Port Settings】Enter the HTTP, HTTPS and RTSP port numbers. Check the Enable UPnP Port
Forwarding box to enable the UPnP function. Click Apply to apply the changes or Cancel to cancel
the changes and return to the previous settings. For setting up the port forwarding function, please
refer to Appendix D. Setting up Port Forwarding Function.
Promoted by the UPnP Forum (Universal Plug and Play), the UPnP is a networking architecture
providing compatibility among networked devices listed in the networked device table. Enable the
UPnP function means you can directly connect the cameras listed in the networked device table by
clicking on them.
Note:
1. For the UPnP function to work, an UPnP-enabled router is required.
2. The UPnP function may fail owing to the compatibility between the camera and the router.
【Multicast Settings】 This function can only be set up in the Advanced tab. Enable if required, fill in
the setting options and click Apply to save. For more details, please refer to Appendix B. Enabling the
Multicast Function.
【DDNS Settings】This function can only be set up in the Advanced tab. DDNS (Dynamic Domain Name
System) is a service used to map a domain name to the dynamic IP address of a network device. You
can set up the DDNS service for remote access to the IP camera. DDNS assigns a domain name (URL)
to the IP camera, so that the user does not need to go through the trouble of checking if the IP
address assigned by DHCP Server has changed. Once the IP is changed, the IP camera will
automatically update the information to the DDNS to ensure it is always available for remote access.
For setting up the DDNS function, please refer to Appendix E. Setting up DDNS Function.
Before enabling the following DDNS function, user should have applied for a host name from the DDS
service provider’s website. We support these four DDNS server providers: www.everfocusddns.com,
www.sitelutions.com, www.dyndns.com, and www.no-ip.com
Note: We highly recommend that you use xxxx.everfocusddns.com for the simplicity of setting up
your IP cameras.

Enable Service ISP: Check this box to enable the DDNS function. You can either apply for a host
name from EverFocus or other DDNS server providers.
 From EverFocus: If you choose the EverFocus DDNS server, you can obtain a free host name
from EverFocus. To obtain a free host name from EverFocus, type a desired host name in the
textbox, click the Register / Update button, and then click the Apply button.
 From other DDNS server providers: To obtain a domain name from one of the three DDNS
server providers, you have to register your name with the provider first, and then select the
provider and fill in the required information. Please refer to the specific DDNS company’s
website for further information.
Record ID: Type the record ID if provided by the DDNS server provider.
31
EZN3261/3361
FQDN: Type the fully qualified domain name applied from the DDNS server provider. For
example, xxxx.dyndns.com
Username / Password: Type the login account of your DDNS server provider.
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous
settings.
Note:
1. In order to support the full functionality of the camera, you must open the port numbers (80,
554, 443) on the router for remote access to the IP camera. This function is available on most
routers in the market and is often known as “Port Forwarding”. To set up Port Forwarding,
please refer to Appendix E. Setting up DDNS Function.
2. In certain router models, it is possible that you will not be able to access the camera using
DDNS while inside the router’s network. Please try using a PC located outside of your router’s
network.
Default Ports on All EverFocus IP Cameras:
HTTP: 80
RTSP: 554
HTTPS: 443
3. The host name obtained from EverFocus DDNS server or other DDNS server should not
include a space, underline or any special characters particularly _~ ! @ # $ % ^ & * ( ) + < >
";:.,
【HTTPS Settings】This function can only be set up in the Advanced tab. Hypertext Transfer Protocol
Secure (HTTPS) is a combination of the Hypertext Transfer Protocol and the SSL/TLS protocol that
provides encrypted communication and secure identification of a network web server. Before using
the HTTPS function for communication with the IP camera, a Certificate must be created first. There
are two ways to create and install a certificate: Self-Signed Certificated and Certificate Request.
Self-Signed Certificated
Please note that even though self-signed certificates are free and offer some protection, true security
is only implemented after the installation of a signed certificate issued by a certificate authority.
1. Select Self-Signed Certificated and fill in the following information.
32
EZN3261/3361
2. Click the Apply button. The subject line will be displayed in the Install Certificated Info field.
3. Click the Property button, a pop-up window appears to display the details of the certificate.
4. To optionally create and install other certificates, remove the existing one by clicking the
Remove button to erase the certificate.
5. On the Web page, change the address from “http://” to https:// in the address bar and press
Enter on the keyboard. Some Security Alert dialogs will pop up. Click OK or Yes to enable HTTPS.
Create Certificate Request
You can apply for an official certificate from an issuing Certificate Authority.
1. Select Certificate Request and fill in the following information.
33
EZN3261/3361
2. Type the required Certificate information and then click the Apply button. The subject line will
be displayed in the Created Request field
3. Click the Property button, a pop-up window appears to display the details of the certificate.
4. To optionally create and install other certificates or request, remove the existing one by clicking
the Remove button to erase the certificate or request.
5. Copy the contents of the Certificate request (in PEM format) and paste it to the certificate
request field on the Web page of the 3rd-party certification authority such as Symantec VeriSign.
Wait for the certificate authority to issue an SSL/TLS certificate and then download the issued
certificate on your computer.
6. In the Install Signed Certificated field, click the Browse button to search for the issued
certificate, and then click the Upload button to import the certificate. Once the certificate has
been uploaded, this field will show the subject line of the certificate.
34
EZN3261/3361
7.1.2 Date / Time
You can set up the system’s time on this page.
【Date/Time Format Settings】Select the desired Date / Time format and then click the Apply button.
To enable displaying the date and time information on the Live View Window, you have to check the
Date/Time box in the Overlay Text Settings (see 7.1.4 Display and Overlay).
【Date/Time Settings】


Manual: Set the date/time if you won’t be using an NTP server to update the date/time. Click
Apply to save the setting.
NTP: Enter the Network Time Protocol server, if applicable. The camera’s time will be
automatically adjusted by synchronizing with the NTP server. Click Apply to save the setting.
【Time Zone Setting】Set the time zone of the camera’s location. Click Apply to apply the changes or
Cancel to cancel the changes and return to the previous settings.
【Daylight Savings Time Settings】Click Enable Daylight Saving to enable this schedule, and select the
dates when the region’s daylight saving period begins and ends. Click Apply to apply the changes or
Cancel to cancel the changes and return to the previous settings.
35
EZN3261/3361
7.1.3 Storage
You can configure the recording path / format, source video stream and SD card settings on this
page.
【Record to Local】This function can only be set up in the Advanced tab. You can configure the storage
path for storing the live stream recordings / snapshot on your PC.



Export Folder: Type the storage path for storing the recordings / snapshot.
File Size: The user can limit the size of each recorded file here (in minutes). Once you click the
Record button on the Live View window, the camera will start recording the live stream to your
computer. When a single recording file exceeds the time you set, the system will create a new
file to save that data to.
Enable Overwrite: Check the box for overwriting recording/snapshot file when the disk storage
capacity is full. The user can set the storage capacity limitation in the in-sentence box below the
Enable Overwrite setting: “If the remaining hard disk capacity is less than ____ MB (50~2000),… “
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous settings.
【Secure Digital Card】

Notification: Select the percentage of storage space that should be left on the card before the
camera notifies you of the impending storage shortage or overwrite.
36
EZN3261/3361

Event Recording: Select the location where you want the camera to send the impending storage
shortage text notification to.
• FTP Back Up Only: Select to send the impending storage shortage text notification to the FTP
server entered in the FTP Repository Settings (see 7.3.3 Notification).
• Event Recording: Select to send the impending storage shortage text notification to the
checked locations in the Event Management (see 7.3.2 Event).
Both: Select to send the impending storage shortage text notification to the FTP or the
selected locations in the Event Management (see 7.3.2 Event).
 Enable Overwrite: Check the box for overwriting files when the SD card is full.
 SD Card Information: If an SD card has been inserted to the card slot of the camera, the SD card
information will be displayed in this field.
 Remove: Click before removing the card from the system (6.2.1 Inserting / Removing the SD
Card).
 Format: Click to format the card. All data saved on the SD card will be removed if the card is
formatted (6.2.1 Inserting / Removing the SD Card).
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous settings.
•
【Recording and Snapshot Settings】Select the desired video stream and recording format. The video
stream can be configured in 7.2.1 Streaming and Audio. Click Apply to apply the changes or Cancel to
cancel the changes and return to the previous settings.
37
EZN3261/3361
7.1.4 Display and Overlay
You can configure the recording path / format, source video stream and SD card settings on this
page.
【Overlay Text Settings】Check the boxes to display the information on the Live View Window. The
information will only be displayed on the Live View Window and will not be displayed on the live view
video images nor snapshots. To change the foreground color of the text, directly click on the box and
then select a color. Select a position where you want the information to be displayed on the Live
Window. To change the Machine Name, see Machine Name in 7.1.5 System Maintenance. To change
the day and time setting, see 7.1.2 Date / Time. Click Apply to apply the changes or Cancel to cancel
the changes and return to the previous settings.
38
EZN3261/3361
【Video Overlay Settings】Check the boxes to enable displaying video title or date/time on the live
view video images. Click Apply to apply the changes or Cancel to cancel the changes and return to
the previous settings.



Show video title in video and snapshots: Check the box to enable displaying video title on the
live view video images and snapshots. To change the title, type a name in the Video Title
column.
Enable Video OSD: Check the box to enable displaying date/time information on the live view
video images. Select the desired Date/Time format.
Position: Select a position where you want the video title or date/time information to be
displayed on the live view video images.
【Live View Layout Settings】Check the box if you want to show the Lens Control buttons or One Push
buttons on the Live View Window. Uncheck this box to hide the buttons. Click Apply to apply the
changes or Cancel to cancel the changes and return to the previous settings.
39
EZN3261/3361
7.1.5 System Maintenance
You can configure the recording path / format, source video stream and SD card settings on this
page.
【Machine Name】If required, enter a new name for the machine. This name will be visible in the
Machine Name field of the IP Utility software, which is included in the software CD. Click Apply to
apply the changes or Cancel to cancel the changes and return to the previous settings.
40
EZN3261/3361
【Language Settings】Select the language to be displayed on the Web interface of the IP camera. The
default language is English.
To add a new language not listed in the current Language list, click the Browse button to locate the
new language file (.evb) on your computer and then click the Upload button. Updated language files
might be available on the manufacturer’s website. Contact your vendor if required.
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous settings.
Note: Uploading a new language file will cause the system to reboot automatically. Please create
a new network connection to the IP camera when the reboot is complete.
【Maintenance】



Reboot: Click to reboot the unit without changing any of the settings. Use this function if the unit
is not behaving as expected.
Restore: Click to restart and reset most of the current settings to their factory default values.
The only settings that will not be changed to default are: IP Settings and DDNS Settings.
Initialize: This function can only be set up in the Advanced tab. This button should be used with
caution. Clicking this button will return all of the camera's settings, including the IP address, to
the factory default values. The camera will then have to be reconfigured.
【Save Configuration Server】
Save: To make a backup file of the machine’s current configurations, click this button to save all the
configurations to a configuration file. This will enable the user to reload these configuration settings if
the settings are changed and there is unexpected behavior.
【Load Configuration Server】
Select Video to apply only the video parameters from the configuration file to the system. Select
Network to apply only the network parameters from the configuration file to the system. Select All to
apply all the parameters from the configuration file to the system.
Browse: Click the Browse button to locate the saved config. File.
Load: Click the Load button to restore the system based on the selected parameters (Video, Network
or All).
【Video Format】Select NTSC or PAL for your local scanning system. Click Apply to save the setting.
【Upgrade Firmware】This function can only be set up in the Advanced tab. Click the Browse button to
find a previously prepared firmware upgrade file. Click the Upload button to install the new
firmware.
41
EZN3261/3361
Note:
1. Do not disconnect power to the unit during the upgrade sequence. The unit will reboot
automatically after the upgrade has completed (1-5 minutes).
2. During the upgrade process, all event recording actions will be stopped. Event recording
actions will resume after the camera is rebooted.
3. If the “File Error, Please re-login!!” warning message appears when upgrading the firmware,
please try the following instructions:
a. Go to Internet Explorer > Tools > Internet Option > Security > Custom.
b. Find and enable the Include local directory path when uploading files to a server.
42
EZN3261/3361
7.1.6 System Information
You can see the system information and log information displayed on this page.
【System Status】Displayed the system information. The values cannot be changed on this page. The
Uptime represents the period since the camera has been powered on. For example, up 21:28
represents the camera has been powered on for 21 hours and 28 minutes.
【System Log】Displayed the sequence number, date, time and event messages of the log event. The
log will display the last 256 log events. Click the Export Log button to export the system log event list
into a “.txt” file and select the location where the exported log file will be saved to. Click the Clear
Log to erase all the log data from the camera. The system will be required to reboot after clicking the
Clear Log button.
43
EZN3261/3361
7.1.7 User
The system administrator can create up to ten user accounts on this page.
【User Management】The system has automatically created ten user accounts.
To set up an user account:
1. Highlight a user account and its information will be displayed in the field below the account list.
2. Revise the account name, password and description. Select an authority level for the user
account.
• Supervisor / Administrator: The only difference between a supervisor and administrator is
that a supervisor can edit an administrator’s account and password, but an administrator
cannot edit the supervisor’s account and password. The supervisor and administrators all
have unrestricted access to the Setting submenus and can determine the registration of all
other users.
44
EZN3261/3361
•
User: A user can not only view the live view but also view/configure the below camera
settings.
View
Configure
System Settings
Network
Network > Protocol Settings
Date/Time
Date/Time > Date/Time Format Settings
Storage > Record to Local
Storage > Record to Local
Display and Overlay > Overlay Text Settings
Display and Overlay > Overlay Text Settings
Display and Overlay > Video Overlay Time
Stamp Settings
Display and Overlay > Video Overlay Time
Stamp Settings
System Maintenance > Language Settings
System Maintenance > Language Settings
System Information
System Information > Export Log
Camera Settings
Streaming and Audio
Camera
Schedule
Image
• Guest: The lowest level of access, which only allows the user access to the live view page.
3. Select Active or Disable to active or disable the user account.
4. Check the Enable SD Card box to allow the user to access the SD card playback function.
5. Click the Edit button to save the changes.
: The button is only activated when the number of list is less than ten. Enter the account
information and click the Create button, the new account will be listed in the account list.
: Highlight an account and then click the Remove button to remove the highlighted account.
: Highlight an account and enter the account information in the boxes below the account list.
Click the Edit button and the account will be edited.
: Click the button to cancel the changes and return to the previous settings.
【Anonymous Settings】Check the box to allow the unauthorized persons to log in the camera. Click
Apply to apply the changes or Cancel to cancel the changes and return to the previous settings.
45
EZN3261/3361
7.1.8 Black/White List
Use this page to specify IP addresses that are allowed / denied to access this camera. By default,
any IP address can access the camera.
Note: The Allowed IP addresses only become relevant when the Denied items contain a
Network or Range, and the supervisor wants to allow one or more IP addresses within that
excluded range or network. In such a scenario, the user would enter the excluded range or
network for the Denied items, and enter the exceptions for the Allowed items.



IP Type: Select IPv4 or IPv6 from the drop-down list.
Permission Type: Select Deny to deny the IP addresses configured below from accessing the
camera. The Allow option is only relevant if you’ve set up at least one Deny item configured with
Network or Range network rule from the Rule drop-down list.
Rule: Select a network rule and then fill in the IP information in the below boxes.
 Single: Type a single IP address in the IP Address field below.
 Network: Type the IP address and subnet mask in the field below.
 Range: Type a range for the IP addresses.
: Set up the IP information and click the Create button, the created IP information will be
listed in the Black/White list.
: Highlight an item in the list and then click the Remove button to remove the highlighted
item.
: Highlight an item in the list and set up the IP information in the boxes below the
Black/White list. Click the Edit button and the item will be edited.
: Click the button to cancel the changes and return to the previous settings.
46
EZN3261/3361
7.2
Camera Settings
You can configure camera related settings, such as video / audio, region of interest and privacy mask.
7.2.1 Streaming and Audio
47
EZN3261/3361
【Stream Settings】This IP camera can output three video streams simultaneously. For each of these
streams, the user can set the compression format, resolution, bit rate, and frame rate individually.
Stream 1 is always enabled for live view. To enable Stream 2, Stream3 and/or Stream 4, check the
Enable Stream 2 / Enable Stream 3 / Enable Stream 4 box.
Note: If you connect to the camera via the Internet and experience a delay (lag time) in the video
feed, try to reduce the number of streams and the quality and resolution of the streams – but
keep the frame rate at its maximum.
Format: Select the encoding format – H.264, MJPEG or MPEG4.
Resolution: Select the most suitable resolution for your needs.
Frame Rate: This function can only be set up in the Advanced tab. Select from 1 to 30 fps.
Bit Rate: This function can only be set up in the Advanced tab. If required, select whether you want
the stream to stream a Constant Bit Rate or a Variable Bit Rate, and set the values of whichever
option you choose.
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous settings.
【Region of Interest Settings】This function can only be set up in the Advanced tab. The Region of
Interest (ROI) function allows users to set up multiple regions within an image with better quality and
less distortion than the rest of the image. You can also use this function together with the Digital
Zoom function on the Live View window to get a better image result. Up to eight ROIs can be
configured in this field.
To set up an ROI region:
1.
2.
Enabled the ROI Draw Tool and click the Draw button .
On the left-side live image, move the cursor to the position where you want the ROI rectangle
to start and then click. Move the cursor to the position (diagonally opposing corner) where
you want the ROI rectangle to end and then click.
3.
4.
Select a quality value for the ROI from the Quality drop-down list.
Click the Apply button to apply the settings, or click the Cancel button to reset without saving
the settings.
48
EZN3261/3361
【Privacy Mask Settings】This function can only be set up in the Advanced tab. The Privacy Mask can
block out sensitive areas from view, covering the areas with colored or black and white boxes in both
live view and recorded clips. This feature is useful when users’ don’t want the sensitive information
visible. Up to four Privacy Masks can be configured.
To set up a Privacy Mask:
1. Enabled the Privacy Mask Draw Tool.
2. From the Color drop-down list, select Color to make the masks appear as colored rectangles
on the screen; or select B/W to make the masks appear as gray rectangles on the screen.
3. Select a color if you select Color from the color drop-down list. Select a level of grayness if you
4.
5.
6.
7.
select B/W from the color drop-down list.
Check the Enable box to enable the configured privacy mask.
Click the Draw button
and move the cursor on the left-side live image.
Move the cursor to the position where you want the mask rectangle to start and then click.
Move the cursor to the position (diagonally opposing corner) where you want the mask
rectangle to end and then click.
Click the Apply button to apply the settings, or click the Cancel button to reset without saving
the settings.
【Audio Settings】The camera can transmit audio to your computer if you have connected an external
microphone / line-in (TRS) audio device to its audio Input. Check the Enable Audio box to enable the
camera’s audio input function. Select an audio input type from the Audio Input drop-down list and
then adjust the audio input volume. Note that the camera provides a line-in 3.5mm jack (TRS),
therefore, TRS microphones with a (built-in) amplifier and external power supply are required.
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous settings.
49
EZN3261/3361
7.2.2 Profile
The Profile Settings is designed with four camera modes, which can be applied in various scenes to
enhance image quality. You can apply different camera modes to the daytime and nighttime.
【Day Mode】Select a camera mode and then click the Apply button to save the settings.




Vivid: Select Vivid mode to have images with optimized contrast ratio. You can further
configure the camera settings on the Camera setup page if required. Note that selecting the
Vivid mode will lock (grayed-out) some Camera Settings on the Camera setup page such as
Exposure Settings (AE), Noise Reduction Settings and Monitor Settings.
Standard: Select Standard mode to have images with system configured settings. You can
further configure the camera settings on the Camera setup page if required. Note that selecting
the Standard mode will lock (grayed-out) some Camera Settings on the Camera setup page such
as Exposure Settings (AE), Noise Reduction Settings and Monitor Settings.
More Detail: Select More Detail mode to enhance the dark parts of the images. You can further
configure the camera settings on the Camera setup page if required. Note that selecting the
More Detail mode will lock (grayed-out) some Camera Settings on the Camera setup page such
as Exposure Settings (AE), Noise Reduction Settings and Monitor Settings.
User Define: Select User Define mode to customize the camera settings. You can configure all
the camera settings on the Camera setup page.
Flicker Compensation: Check the box to enable the Flicker Compensation function. Please enable
this function only if flicker artifacts are observed.
50
EZN3261/3361
【Night Mode】Select a camera mode and then click the Apply button to save the settings.




High Contrast: Select High Contrast mode to have images with higher contrast ratio. You can
further configure the camera settings on the Camera setup page if required. Note that selecting
the High Contrast mode will lock (grayed-out) some Camera Settings on the Camera setup page
such as Exposure Settings (AE), Noise Reduction Settings and Monitor Settings.
Standard: Select Standard mode to have images with system configured settings. You can
further configure the camera settings on the Camera setup page if required. Note that selecting
the Standard mode will lock (grayed-out) some Camera Settings on the Camera setup page such
as Exposure Settings (AE), Noise Reduction Settings and Monitor Settings.
More Detail: Select More Detail mode to enhance the dark parts of the images. You can further
configure the camera settings on the Camera setup page if required. Note that selecting the
More Detail mode will lock (grayed-out) some Camera Settings on the Camera setup page such
as Exposure Settings (AE), Noise Reduction Settings and Monitor Settings.
User Define: Select User Define mode to customize the camera settings. You can configure all
the camera settings on the Camera setup page.
Blur Compensation: Check the box to enable the Blur Compensation function. Please enable this
function only if motion blur is observed.
51
EZN3261/3361
7.2.3 Camera
【Day/Night Settings】

•
•
•
•
•
Mode: Select a mode from the drop-down list.
Auto: Select to let the camera automatically switch to Night mode (black and white images
with IR LED on) when the light levels fall to a specified level, and back to Day mode (color
images) when the light levels rise to a specified level.
Day: Select to keep the camera in Day mode (color images with IR LED off), even in nighttime.
Night: Select to keep the camera in Night mode (black and white images with IR LED on), even
in daytime.
Schedule: Select to let the camera to switch to Day mode or Night mode (IR LED on) based on
the day and night schedule settings (see 7.2.4 Schedule).
Auto mode without IR LED: Select to let the camera automatically switch to Night mode
(black and white images with IR LED off) when the light levels fall to a specified level, and back
to Day mode (color) when the light levels rise to a specified level.
52
EZN3261/3361
Night mode without IR LED: Select to keep the camera in Night mode (black and white images
with IR LED off), even in daytime.
• Schedule without IR LED: Select to let the camera to switch to Day mode or Night mode (IR
LED off) based on the day and night schedule settings (see 7.2.4 Schedule).
 D/N Level: This function can only be activated if you select Auto / Auto mode without IR LED
mode in the Day/Night Settings field. Adjust the level (1-4 lux) for the camera to switch from
Day mode to Night mode based on the light level detected by the Light Sensor. The camera will
switch back from Night mode to Day mode when the detected light level has reached 2-level
higher than the level you have set up.
For example:
If you set up the D/N level to 1 (lux), the camera will automatically switch from:
• Day to Night when the light level is below 1 lux.
• Night to Day when the light level has reached 3 lux.
•
If you set up the D/N level to 2 (lux), the camera will automatically switch from:
• Day to Night when the light level is below 2 lux.
• Night to Day when the light level has reached 4 lux.
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous settings.
Day Profile/ Night Profile: Select Day Profile to configure the following settings for daytime and select
Night Profile to configure the following settings for nighttime. Click the Apply button to save the
settings.
Note: Some settings in the Exposure Settings / Features may be grayed-out. To configure all the
settings, select User Define from the Day Mode / Night Mode drop-down list (see 7.2.2 Profile).
【Lens Settings】Click Apply to apply the changes or Cancel to cancel the changes and return to the
previous settings.
 Focus Mode: Select Manual to manually adjust the focus or select Auto to enable the Focus
button on the live view window (see 5.4 Live View Window). Note that if you select Auto, the
camera will automatically adjust focus every time when you click the zoom in/out button on the
Live View window or push the 5-Axis Button to zoom (see 3.2 5-Axis Button).
【Exposure Settings】This function can only be set up in the Advanced tab and can only be activated
when you select User Define from the Day Mode / Night Mode drop-down list (see 7.2.2 Profile). This
setting is used to adapt to the amount or type of light used by the camera. Click Apply to apply the
changes or Cancel to cancel the changes and return to the previous settings.
 Mode: Select a mode from the drop-down list.
• Auto: Selecting Auto for the camera to automatically adjust the Shutter based on the
measured light level.
53
EZN3261/3361
ALC (Shutter Priority): Selecting ALC (Automatic Light Control) allows the camera circuitry to
either take bright spots more into consideration (peak), bringing out detail in bright areas,
or less into consideration (average) bringing out detail in shadows.
• Manual: Select this option to manually set up the IRIS, Shutter (Manual) and AGC (Manual)
values.
IRIS: This function is only activated if you select Manual in the Mode field.
Shutter (Manual): The function is only activated if you select ALC or Manual in the Mode field.
If enabled, this setting lets you set the shutter speed yourself (measured in fractions of a
second).
AGC (Manual): The function is only activated if you select Manual in the Mode field. Set the
Auto Gain Control limit here. The lower the AGC level, the lower the video signal and the noise.
Slow Shutter: The function is only activated if you select Auto in the Mode field.
AGC: The function is only activated if you select Auto or ALC in the Mode field. Set the Auto
Gain Control limit here. The lower the AGC level, the lower the video signal and the noise.
Flickerless: The function is only activated if you select Auto in the Mode field. Choose between
OFF, 50HZ, 60HZ, 50HZ (High Luminance) or 60HZ (High Luminance).
•






【Backlight Compensation Settings】The Backlight Compensation (BLC) function is useful when the
background of the subject is very bright and the subject itself is dark. Click Apply to apply the changes
or Cancel to cancel the changes and return to the previous settings.
BLC Edit Mode: Click the Enable button, the BLC grids appear on the
image. Click on the grids to enable / disable the BLC function. The
selected grids (in green) will be applied with the BLC function.
【Features】This function can only be set up in the Advanced tab. Click Apply to apply the changes or
Cancel to cancel the changes and return to the previous settings.
 Noise Reduction (NR): This limits the amount of digital “video noise” that is usually found in any
video stream, and helps to reduce file size. Select ON / OFF to enable / disable the Noise
Reduction function. Slide the Level bar to set up the level. The higher the level, the more the
reduction. Note that this function can only be activated when you select User Define from the
Day Mode / Night Mode drop-down list (see 7.2.2 Profile).
 Wide Dynamic Range (WDR): The WDR function provides clearer images when both of the very
bright and dark areas simultaneously appear on the camera view. There are three value options:
OFF, ON and Auto. Note that when WDR is ON, some parts of the image may appear solarized.
This is normal for WDR, and is not a camera malfunction.
 Monitor Type: Users can use this field to optimize video quality of the monitor. Note that this
function can only be activated when you select User Define from the Day Mode / Night Mode
drop-down list (see 7.2.2 Profile).
54
EZN3261/3361
7.2.4 Schedule
The Schedule setup page is designed for users to configure the daytime and nighttime of each day.
The Schedule setting is only functional if you select Schedule from the D/N Mode drop-down list on
the Camera setup page.
Select Night and then move the cursor on the desired time square, click and drag the cursor over
the time squares to configure them to the Night mode (green color). Select Day and then move the
cursor on the desired time square, click on the time squares to configure them to the Day mode
(gray color).
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous
settings.
55
EZN3261/3361
7.2.5 Image
This function can only be set up in the Advanced tab.
【Orientation Settings】
Enable Mirror: Check the box to enable the mirror function. The image will be rotated
horizontally around a vertical axis.
 Enable Flip: Check the box to enable the flip function. The image will be rotated vertically
around a horizontal axis.
【Image Settings】Select Day or Night and then adjust the slide bars below to configure the brightness

and sharpness for daytime or nighttime.
【Color Settings】Slide the bar to adjust the saturation.
【White Balance Settings】Select a mode that delivers the best image quality for the camera’s light
environment.
 Auto: Select to let the camera automatically adjust the White Balance. In the Auto mode the
camera computes the white balance value output using color information from the entire
screen. It outputs the proper value using the color temperature radiating from a black subject
based on a range of value from 3000 to 7500K.
 Manual: Select to adjust the Red and Blue values yourself in the fields below this field.
56
EZN3261/3361
7.3
Event Settings
You can set up the Motion Detection event or Tampering Detection event to automatically notify the
users when an event occurs. You can also set up a schedule to automatically record the videos when
an event occurs.
7.3.1 Event Wizard
The Event Wizard allows users to easily configure the event settings. Follow the on-screen
instructions to complete the event settings.
57
EZN3261/3361
7.3.2 Event
This function can only be set up in the Advanced tab. Except the Event Wizard, you can also
configure the event settings along with the Recording Schedule on this page.
58
EZN3261/3361
【Event Management】You can set up the events such as Motion Detection or Tampering Detection to
automatically notify the users when an event occurs.
Event Name: Type an event name.
 Event Trigger Type: Select an event for the to-be-specified-below reaction/s.
• Alarm Input: Select this if you want a reaction trigger coming from any external, connected
sensor to activate a to-be-specified-below reaction/s via the camera system. Make sure
that a suitable device is actually connected to the alarm input relay.
• Manual Trigger: Select this option if you want to manually trigger the alarm by clicking the
Trigger Event button on the Live View Page.
• Motion Detection: Select this option to trigger the to-be-specified-below reaction/s when
motion events occur. You have to pre-configure the Motion Settings for this function to
work.
• Schedule Recording: Select this option if you want the Schedule Recording periods
configured in the Schedule Settings to activate this event. In this scenario, a preconfigured
event reaction like a log entry will list the start and end times of each period. Actual
recording will only be triggered if the event is preconfigured to do so.
• Tampering Detection: Select this option if you want the camera’s tampering detection
sensor to trigger the to-be-specified-below reaction/s. You can set up the tamper duration
time in the Event Trigger Settings field below.
 Enable This Event: Check the box to activate the event.
 Enable Re-trigger minimum interval between triggers xx second: Check the box to set a
minimum time after the event is triggered before the event can be triggered again.
 Enable Pre-trigger Buffer: Check the box if you want the Event reaction (as selected in the
“Notification Over” field below) to be the activation of the video recording function, and if you
want the recording to include the video feed from the time period (configurable in the
Schedule Settings field) just before the Event trigger occurred.
 Enable Post-trigger Buffer: Check the box if you want the Event reaction (as selected in the
Notification Over field) to be the activation of the video recording function, and if you want the
recording to include the video feed from a time period (configurable in the Schedule Settings
field) just after the Event trigger occurred.
Notification Over: Select the desired notification types from the following items.
 Log: Check the box if you want the camera to list the event’s details in its log if the event is
triggered.
 Trigger Alarm Output: Check if you want the camera to relay the event reaction to a device
attached to the alarm relay output wire and then set up the alarm output duration time.
 Send Mail Notification: Check the box if you want the camera to send an email text
notification and one image file to the email address entered in the SMTP Settings field (see
7.3.3 Notification).
59
EZN3261/3361

Upload to FTP: Check the box if you want the camera to upload the recordings to the FTP
server entered in the FTP Repository Settings (see 7.3.3 Notification).
Note: When network or FTP server failure occurs, the FTP uploading cannot be performed,
the recordings will be stored in the on-camera SD card. The FTP uploading will resume after
network or FTP server is recovered.

Record to SD Card: Check the box if you want the camera to start recording its video feed
(when the event occurs) on an on-camera SD Card (if such a card has been inserted).
Note: The recording will only be as long as the combined Pre- and Post-trigger Buffers, so
make sure you enable at least one of these buffers, especially the Post-trigger Buffer.

Network Alarm: Check the box if you want the camera to send a network alarm signal (when
the event occurs) to the CMS servers. Note that you have to configure the Network Alarm
Settings for this function to work (see 7.3.3 Notification).
: Set up the Event information and click the Create button, the created Event information
will be listed in the Event List.
: Highlight an item in the Event List and then click the Remove button to remove the
highlighted item.
: Highlight an item in the Event List and edit the Event information on the left-side. Click
the Edit button and the item will be edited.
: Click the button to cancel the changes and return to the previous settings.
【Event Trigger Settings】



Input 1 Trigger Type: Select Normal Open or Normal Close from the drop-down list.
Output 1 Contact Type: Select Normal Open or Normal Close from the drop-down list.
Tamper Duration Time: Set up a duration time between 10 and 120 seconds. When a
tampering event has been detected and the duration reached the setup time, the camera will
trigger the event.
【Trigger Options Settings】

Pre-trigger Buffer: Select the duration for the buffer. This will determine the amount of
footage (length of time) before the event trigger moment that will be included in an
event-triggered video recording, if that buffer and video recording has been enabled in the
Event Management field.
60
EZN3261/3361

Post-trigger Buffer: Select the duration for the buffer. This will determine the amount of
footage (length of time) after the event trigger moment that will be included in an
event-triggered video recording, if that buffer and video recording has been enabled in the
Event Management field.
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous settings.
【Schedule Settings】Users can configure the recording schedule here. Select the desired recording
types among the options below. Click and drag the cursor on the time block, which will be applied
with the selected recording type.
 Event Recording (Red): Select for the camera to activate all the Event Recording set up in the
Event Management field (Event Trigger Type), except the Schedule Recording.
 Schedule Recording (Green): Select for the camera to activate only the Schedule Recording set
up in the Event Management field (Event Trigger Type).
 Event + Schedule (Yellow): Select for the camera to active both of the configured Event and
Schedule Recordings.
 Deselect (Grey): Select for the camera to stop recording.
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous settings.
【Motion Settings】Use this page to configure up to four areas in which motion will be detected.
When a motion is detected by the camera, the motion detection icon
will appear at
the top right corner on the Live page to alert the user. This function can also be linked with
correctly configured Events to trigger Event reactions like the activation of video recording periods,
snapshots, etc.
To set up the Motion area:
1. Check the Enable box to enable the selected area.
2. Select a sensitivity value of the motion detection sensor function.
3.
4.
5.
Click the Draw button
and move the cursor on the left-side live image.
Move the cursor to the position where you want the motion rectangle to start and then click.
Move the cursor to the position (diagonally opposing corner) where you want the motion
rectangle to end and then click.
Click the Apply button to apply the settings, or click the Cancel button to reset without saving
the settings.
61
EZN3261/3361
7.3.3 Notification
This function can only be set up in the Advanced tab.
62
EZN3261/3361
【SMTP (Email) Settings】This area is for configuring the mail server that is used to send e-mail text
notifications and one image file from the camera to predefined addresses via SMTP. Note that to
enable e-mail notification function, you have to check the Send Mail Notification box in the Event
Management field (see 7.3.2 Event).
SMTP Server: Enter the IP address or the host name of the SMTP server used to send e-mails.
 SMTP Port: Enter the port number for SMTP. The default is 25.
 Authentication: Check the box if the SMTP server requires authentication (user/password).
 Username: Input the user’s login ID if the SMTP server requires authentication.
 Password: Input the user’s login password if the SMTP server requires authentication.
 Receiver Address: Input the e-mail addresses for receiving an e-mail message when events
occur. Please use “;” to separate multiple addresses.
 Sender Address: Input the sender’s e-mail address, so that the receiver can recognize the
sender when an event message is received.
• Attach Image: Check the box if you want to attach an image when events occur.
• SSL Connection: Check the box to enable the SSL function. Enable this function means you
can access the camera through the SSL protocol that provides communication security over
the Internet.
 Send Test Email: Click the Test button to send a testing email to the assigned address.
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous settings.

【FTP Repository Settings】This area is for configuring the FTP server that is used to send alarm
recordings from the camera to the preconfigured FTP server. Note that to enable uploading
recordings to the FTP server function, you have to check the Upload to FTP box in the Event
Management field (see 7.3.2 Event).
Note: When network or FTP server failure occurs, the FTP uploading cannot be performed, the
recordings will be stored in the on-camera SD card. The FTP uploading will resume after network
or FTP server is recovered.





FTP Server: Enter the IP address or the host name of the FTP server.
FTP Port: Enter the port number for the FTP server. Default is 21.
Recording Path: Assign the recording path.
Username: Set FTP User’s name.
Password: Set FTP password.
63
EZN3261/3361
PASV mode: Check the box to enable Passive mode. Passive mode is normally enabled. If a
connection cannot be established, uncheck "PASV Mode”.
 Test FTP Server: Click the Test button to send a testing file to the assigned FTP server.
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous settings.

【SNMP Settings】The default values for SNMP v1/v2/v2c and SNMP v3 are already filled in. Click
either of the Enable buttons to enable either of the two. Make your changes as desired. Click on the
Trap Address field to enter the digits, if required.
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous settings.
【Network Alarm Settings】This function works with EverFocus CMS software. The camera can send a
network alarm signal (when the event occurs) to the CMS servers. To establish the connection
between the camera and CMS servers, the protocol and port number should match with each other.
For more details, please refer to the CMS user’s manual. Note that to enable the Network Alarm
function, you have to check the Network Alarm box in the Event Management field (see 7.3.2
Event).
Click Apply to apply the changes or Cancel to cancel the changes and return to the previous settings.
64
EZN3261/3361
7.4
Link to Smart Phone App
You can access camera live view or take a snapshot via your smart phone. This page is designed for
users to download the mobile app to your mobile phone by scanning the QR code.
MobileFocus
for iPhone
MobileFocusPlus
for iPhone
65
MobileFocus
for Android-based smart phone
EZN3261/3361
8.
Upgrading Firmware Using IP Utility
You can upgrade the Firmware using the IP Utility software included in the software CD. The IP Utility can
also be downloaded from EverFocus’ Website (below link). Please connect the IP camera on the same
LAN of your computer. http://www.everfocus.com/HQ/Support/DownloadCenter_p1.aspx.
1. Save IP Utility Setup .exe
in your computer. Double click the .exe file and follow the on‐screen
instructions to install the IP Utility.
2.
Click the Finish button, the IP Utility will be automatically launched to search the IP devices
connected on the same LAN.
3.
Log in the device by checking the desired model and then click the Log in
box appears.
66
icon. The Log in dialog
EZN3261/3361
4.
Type the Username and Password and click OK. The status column will display Login.
Note:
1.
2.
3.
The default user ID is user1 and the default password is 11111111.
If you select more than one camera that has the same user ID / password, you will be able
to log in several cameras at once.
Up to 10 cameras can be simultaneously upgraded to the latest firmware. If you connect
the cameras to a PoE switch, please make sure the Power Consumption of the PoE switch
is sufficient.
5.
Click the Upgrade Firmware button
, a browsing window appears.
6.
Select the firmware file (.evb) and then click Open. The IPU will automatically upgrade the firmware.
The camera will reboot once the upgrade process is complete.
67
EZN3261/3361
9.
Specifications
Model
EZN3261
EZN3361
Camera
Image Sensor
1/3" CMOS Sensor
Megapixel
2 MP
Min. Illumination
Color: 0.5 lux at F1.8
B/W: 0.095 lux at F1.8
0 lux at F1.8 (IR LEDs on)
Electronic Shutter
8 ~ 1/15,000 sec.
Scanning System
NTSC / PAL
WDR
Yes
BLC
Yes
Optical Zoom
10x
Digital Zoom
10x
Image Setting
Compression, Brightness, Sharpness, Saturation, White Balance, Exposure
Control, Rotation, Mirroring of Images, Text and Image Overlay, Auto Gain
Control, Digital Noise Reduction, Auto White Balance, Hallway Display (9:16)
Event Trigger
Manual Trigger, Motion Detection, Tamper Detection
Notification
Send mail notification, upload video to FTP, record video to PC and Network
alarm
3 MP
Lens
Iris
DC Iris
Focal Lens
4.9 ~ 49 mm, 10x optical zoom lens
Aperture Ratio
F1.8 ~ 360C
True Day / Night
Yes (with removable IR-cut filter)
Horizontal Wide 100° / Tele 27.3°
Angle of View
Vertical
Wide 73.3° / Tele 20.4°
Diagonal
Wide 129.1° / Tele 34.3°
IR Distance
40 m / 131 ft
IR LED Quantity
12
Video
Video Compression
H.264, MPEG4 and MJPEG
NTSC
2048 x 1536, 1920 x 1200 (for EZN3361 only), 1920 x 1080, 1280 x 1024,
1280 x 720, 1024 x 768, 720 x 480, 704 x 480, 640 x 480, 352 x 240,
320 x 240, 160 x 120
PAL
2048 x 1536, 1920 x 1200 (for EZN3361 only), 1920 x 1080, 1280 x 1024,
1280 x 720, 1024 x 768, 720 x 576, 704 x 576, 640 x 480, 352 x 288,
320 x 288, 160 x 120
Resolution
68
EZN3261/3361
Frame Rate
30 fps at 1920 x 1080
S/N Ratio
Audio
> 50dB
Audio Streaming
Two-way audio
Audio Compression
G.711
30 fps at 2048 x 1536
Network
Interface
10 / 100 Base-T Ethernet, LAN / PoE Cable
Supported Protocols
TCP/IP, IPV6, UDP, ICMP, DHCP, NTP, DNS, DDNS, SMTP, SNMP, FTP,
HTTP, HTTPs, PPPoE, UPnP, Bonjour, RTP, RTSP, RTCP, UDP, IGMP, ICMP,
ARP, ONVIF, PSIA
Security
Password protection, IP address filtering, HTTPS encryption, SSL
Mechanical
Memory Card
Camera
Angle
Adjustment
Cables
One micro SD / SDHC card slot (see Appendix for the tested card brands)
Pan
360°
Tilt
90°
Rotate
360°
Alarm In/Out
4-Pin terminal block
Audio Input
Line-in 3.5mm stereo (TRS) jack (pink)
Audio Output
speaker (green)
Power
12 VDC input
LAN / PoE
Connects to a 10 / 100 Base-T Ethernet or PoE
General
Power Source
12VDC / PoE (IEEE802.3at Class 4)
Max. Power Consumption
11W (12VDC)
14W (PoE)
12.98W (12VDC)
15.55W (PoE)
Humidity
-40°C ~ 55°C / -40°F ~ 131°F (12VDC)
-20°C ~ 55°C / -4°F ~ 131°F (PoE)
20% ~ 80% (no condensation)
Safety
CE, FCC
Weather Resistant
IP66-rated
Dimensions (Φ x L)
(Φ x H x L)
Φ105.5 x 328.7 mm / Φ4.15” x 12.94” (In Line)
Φ105.5 x 123.5 x 295.49 mm / Φ4.15” x 4.86” x 11.63” (Right Angle)
Weight
1.432 kg / 3.15 lbs
Language
Czech, Dutch, English, French, German, Japanese, Polish, Portuguese,
Russian, Simplified Chinese, Spanish, Traditional Chinese
Operating Temperature
69
EZN3261/3361
10. Troubleshooting
Error messages pop up
A. When these error messages pop up, follow the steps below to fix the problem.
1. To enter the Registry Editor of your computer: Click Start and type “regedit” in the Search Program and
Files field.
2. Click the Enter button, the Registry Editor window appears.
70
EZN3261/3361
3. Find the KeepAlive Timeout Dword by following the path:
\HKEY_CURRENT_USER\Sofware\Microsoft\Windows\CurrentVersion\Internet Settings
4. Double-click KeepAlive Timeout and this window appears.
5. Change the Value data to 480000 and click OK.
71
EZN3261/3361
B. Snapshot / Record error message.
For Microsoft IE10 and above users, you may have the above error message pop up when you click the
Snapshot
or Record
button on the Live View window. You can simply solve this problem
by setting up your Microsoft Internet Explorer to Run as administrator.
72
EZN3261/3361
Appendix
A. Tested Card Brands
This IP Camera supports SD / SDHC card up to 64 GB. The following brands of the SD / Micro SD cards have
been tested by EverFocus and are recommended to work with EverFocus IP camera.
Brand
ADATA
Kingston
Samsung
SanDisk
Transcend
Card Capacity
64 GB
64 GB
64 GB
64 GB
64 GB
Card Rate Level
Class 10
Class 10
Class 10
Class 10
Class 10
ADATA: Premier microSDHC/SDXC UHS-I Class10
Kingston: MicroSDXC UHS-I Class10 64GB
Samsung: MicroSDXC 64GB UHS-I
SanDisk: Ultra® microSDXC™ UHS-I card
Transcend: MicroSDXC Class 10 UHS-I memory card 300x
73
EZN3261/3361
B. Enabling the Multicast Function
The Multicast Function is a technique for one-to-many communication over an IP infrastructure in a
network that is designed to share IP camera loading and reduce network bandwidth. Note that for this
function to work, the router / switch must support multicast function.
Multicast
IP Camera
Streaming
Switch
Router
Router
Switch
To enable the Multicast Function:
1. Complete the installation of the IP cameras, routers/ switches and computers (refer to diagram above).
2. Access to the Web UI of the IP camera to enable the Multicast function. Click the Apply button to save the
setting. (Advanced tab > Network> Multicast Settings> Enable Multicast)
74
EZN3261/3361
3. Go to the setting page of the router/switch to enable the Multicast function.
Here we use a D-Link DIR655 router and EverFocus 24-port switch for example.
4. The Multicast function setup is now complete.
75
EZN3261/3361
C. RTSP URL Syntax
Following is the RTSP URL syntax of EverFocus’ IP cameras.
rtsp://[device-ip-address]:554/Streaming/channels/[0]
* [device-ip-address] is the IP address of the IP camera
* [0] is for Main Stream; [1] is for Sub Stream
For example, if the IP address of the IP camera is 192.168.37.55, the RTSP URL (main stream / sub stream)
of this IP camera will be:
Main Stream:
rtsp://192.168.37.55:554/Streaming/channels/0
Sub Stream:
rtsp://192.168.37.55:554/Streaming/channels/1
76
EZN3261/3361
D. Setting up Port Forwarding Function
IP Camera port forwarding can be used when users need to access a certain IP camera from outside of the
local network where the IP camera is connected to.
To enable the IP camera port forwarding function, you have to configure the port forwarding settings both
on the IP camera and the router (UPnP-enabled). Please follow the steps below:
Internet
Local Network
IP Camera
PC
Router
Switch
Notebook
1. On the Setting page of the IP camera (Setting < System Setting < Network)
a. Set up a static IP for the IP camera. Type in the subnet mask, gateway and the DNS if provided
by the Internet Service Provider. Click the Apply button.
77
EZN3261/3361
b. Enter the port numbers and check the Enable UPnP Port Forwarding box to enable the port
forwarding function. Click the Apply button.
The default ports of all EverFocus’ IP cameras are as below. You can change the port numbers if
necessary. Be sure the port numbers setup on the router match the ones setup here.
HTTP: 80
HTTPS: 443
RTSP: 554
2. Set up the port forwarding settings on the router. Here we use D-Link’s router for example.
Please be noted that each router may look different in some ways, however, the concept of the
port forwarding setting is the same. For more details, please consult the manual of your router.
Enter the IP address of the IP camera
Enter the HTTP/HTTPS/RTSP port
numbers of the IP camera
3. Open a browser and type in the IP address of the router, now you are able to access the IP camera
from the Internet.
78
EZN3261/3361
E. Setting up DDNS Function
If you set up your IP Camera with DHCP network, the IP address of your IP Camera may change at different
times for different reasons, particularly after a power failure. The changing IP address of the IP Camera
may cause you difficulties accessing the IP Camera. To solve this problem, you can set up the DDNS
function to your IP Camera, and access your IP Camera with a fixed host name whenever the IP address of
your IP Camera changes.
DDNS (Dynamic Domain Name System) is a service used to map a domain name to the dynamic IP address
of a network device. It assigns a domain name (URL) to the IP Camera, so that the user does not need to
go through the trouble of checking if the IP address assigned by DHCP Server has changed. Once the IP is
changed, the IP Camera will automatically update the information to the DDNS to ensure it is always
available for remote access.
To set up DDNS for your IP Camera, you have to 1) enable the DMZ or Port Forwarding function of your
router 2) configure the network setting of your IP Camera 3) configure the DDNS setting of your IP Camera.
Please follow the steps below.
To enable the DDNS function:
1. In order to access the IP camera from outside of the local network, enable either the Port Forwarding
or DMZ function of your router. Please refer to the manual of your router for more details.
Note: If you enable the Port Forwarding of your router, the Enable UPnP Port Forwarding function
must be enabled on the IP camera (see Port Settings field in the Step 2 image).
79
EZN3261/3361
2.
On the Network Setting page (Setting > System Settings > Network > IP Settings), configure the IP
Settings, keep the default Port Settings and then click the Apply button.
80
EZN3261/3361



3.
If Static IP is selected: Enter the IP address, subnet mask, default gateway and the DNS Server.
Please consult with your ISP service provider for the information of subnet mask, default gateway
and the DNS Server.
If DHCP is selected: The IP address, subnet mask, default gateway and the DNS Server will be
assigned automatically by DHCP server.
If PPPoE is selected: Enter the User Name (e.g. xxxx@hinet.net) and Password provided by your
ISP service provider.
In the DDNS Settings field (Setting > System Settings > Network > DDNS Settings), register a free host
name from EverFocus DDNS and then click the Apply button.
a.
Check Enable Service ISP to enable the DDNS function.
b. Select www.everfocusddns.com and enter a desired host name in the IP Camera Name field. If
the host name is available, a “Success” window will appear. Click OK. If not, try another host
name until the “Success” window appears.
Note: The host name should not include a space, or a dot (period) or any special characters
particularly _~ ! @ # $ % ^ & * ( ) + < > " ; : . ,
c.
Click Apply.
81
EZN3261/3361
4.
The DDNS setup is now complete. Open a browser and enter the domain name (http://[host
name].everfocusddns.com) in the address field. The Web interface of the device should be displayed.
For example, if you’ve obtained the host name “HQtest” from EverFocus DDNS server, enter
http://HQtest.everfocusddns.com in the address field of the browser.
82
EverFocus Electronics Corp.
EverFocus Taiwan:
12F, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, New Taipei City, Taiwan
TEL: +886 2 2698 2334
FAX: +886 2 2698 3943
www.everfocus.com.tw
marketing@everfocus.com.tw
EverFocus Europe - Germany:
Albert-Einstein-Strasse 1, D-46446
Emmerich, Germany
TEL: +49 2822 93940
FAX: +49 2822 939495
www.everfocus.de
sales@everfocus.de
EverFocus China - Beijing:
Room 609, Technology Trade Building,
Shangdi Information Industry Base,
Haidian District, Beijing 100085, China
TEL: +86 10 6297 3336~39
FAX: +86 10 6297 1423
www.everfocus.com.cn
marketing@everfocus.com.cn
EverFocus China - Shenzhen:
4F, No. 2, D4 Building, Wan Yelong
Industrial Park, Tangtou Road, Shiyan,
Baoan, Shenzhen, Guangdong 518101, China
TEL: +86 755 2765 1313
FAX: +86 755 2765 0337
www.everfocus.com.cn
marketing@everfocus.com.cn
EverFocus USA - California:
1801 Highland Avenue, Unit A, Duarte, CA 91010, USA
TEL: +1 626 844 8888
FAX: +1 626 844 8838
www.everfocus.com
sales@everfocus.com
EverFocus Japan:
3F, Kuramochi, Building II
2-2-3 Koto-Bashi, Sumida-Ku,
Tokyo, 130-0022, Japan
TEL: +81 3 5625 8188
FAX: +81 3 5625 8189
www.everfocus.co.jp
info@everfocus.co.jp
Your EverFocus product is designed and
manufactured with high quality materials
and components which can be recycled
and reused.
This symbol means that electrical and
electronic equipment, at their
end-of-life, should be disposed of
separately from your household waste.
Please, dispose of this equipment at your
local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Ihr EverFocus Produkt wurde entwickelt
und hergestellt mit qualitativ
hochwertigen Materialien und
Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte am
Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!
P/N: 4605PZ3261B010A-Ver.B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising