EverFocus | eIVP5600 | Owner Manual | Everfocus eIVP5600 Owner Manual

Everfocus eIVP5600 Owner Manual
eIVP5600
Intel Gen7 Core i7-7600U/i5-7300U Mobile NVR
Supporting 8-Channel PoE IP Cameras
User’s Manual
Copyright © EverFocus Electronics Corp.
Release Date: October 2019
EVERFOCUS ELECTRONICS CORPORATION
eIVP5600
Intel Gen7 Core i7-7600U/i5-7300U Mobile NVR
supporting 8-Channel PoE IP Cameras
User’s Manual
 1995-2019 EverFocus Electronics Corp.
www.everfocus.com.tw
Disclaimer
All the images including product pictures or screen shots in this document are for example only. The
images may vary depending on the product and software version. Information contained in this document
is subject to change without notice.
Copyright
All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form
or by any means without written permission of the EverFocus Electronics Corporation.
Microsoft Windows is a registered trademark of Microsoft Corp.
Intel, Pentium, Celeron, and Xeon are registered trademarks of Intel Corporation
Core, Atom are trademarks of Intel Corporation
ITE is a trademark of Integrated Technology Express, Inc.
IBM, PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation.
All other product names or trademarks are properties of their respective owners.
Safety Precautions
Please read the following safety instructions carefully. It is advised that you keep this manual
for future references.
 All cautions and warnings on the device should be noted.
 All cables and adapters supplied by EverFocus are certified and in accordance with the
material safety laws and regulations of the country of sale. Do not use any cables or
adapters not supplied by EverFocus to prevent system malfunction or fires.
 Make sure the power source matches the power rating of the device.
 Position the power cord so that people cannot step on it. Do not place anything over the
power cord.
 Always completely disconnect the power before working on the system’s hardware.
 No connections should be made when the system is powered as a sudden rush of power
may damage sensitive electronic components.
 If the device is not to be used for a long time, disconnect it from the power supply to avoid
damage by transient over-voltage.
 Always disconnect this device from any AC supply before cleaning.
 While cleaning, use a damp cloth instead of liquid or spray detergents.
 Make sure the device is installed near a power outlet and is easily accessible.
 Keep this device away from humidity.
 Place the device on a solid surface during installation to prevent falls.
 Do not cover the openings on the device to ensure optimal heat dissipation.
 Watch out for high temperatures when the system is running.
 Do not touch the heat sink or heat spreader when the system is running.
 Never pour any liquid into the openings. This could cause fire or electric shock.
 As most electronic components are sensitive to static electrical charge, be sure to ground
yourself to prevent static charge when installing the internal components. Use a grounding
wrist strap and contain all electronic components in any static-shielded containers.
 If any of the following situations arises, please contact our service personnel
(ts@everfocus.com.tw):
-
Damaged power cord or plug
Liquid intrusion to the device
Exposure to moisture
Device is not working as expected or in a manner as described in this manual
The device is dropped or damaged
Any obvious signs of damage displayed on the device
 DO NOT LEAVE THIS DEVICE IN AN UNCONTROLLED ENVIRONMENT WITH TEMPERATURES
BEYOND THE DEVICE’S PERMITTED STORAGE TEMPERATURES (SEE SPECIFICATION) TO
PREVENT DAMAGE.
ii
FCC Statement
This device complies with Part 15 FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received including
interference that may cause undesired operation.
Caution:
There is a danger of explosion if the battery is incorrectly replaced. Replace only with the same
or equivalent type recommended by the manufacturer. Dispose of used batteries according to
the manufacturer’s instructions and your local government’s recycling or disposal directives.
Attention:
Il y a un risque d’explosion si la batterie est remplacée de façon incorrecte.
Ne la remplacer qu’avec le même modèle ou équivalent recommandé par le constructeur.
Recycler les batteries usées en accord avec les instructions du fabricant et les directives
gouvernementales de recyclage.
iii
RoHS Requirements
設備名稱 (Equipment): 網路數位錄放影機,型號(型式)/ Type designation (Type): eIVP5600
單元Unit
印刷電路板及
電子零組件
限用物質及其化學符號 Restricted substances and its chemical symbols
鉛Lead
汞Mercury
鎘Cadmium
(Pb)
(Hg)
(Cd)
六價鉻
Hexavalent
chromium
多溴聯苯
Polybrominated
biphenyls
(Cr+6)
(PBB)
多溴二苯醚
Polybrominated
diphenyl ethers
(PBDE)
○
○
○
○
○
○
Wires &
Connectors for
External
Connections
○
○
○
○
○
○
外殼 Chassis
○
○
○
○
○
○
中央處理器與
內存
○
○
○
○
○
○
硬碟 Hard Disk
○
○
○
○
○
○
電源 PSU
○
○
○
○
○
○
PCB & Other
Components
外部訊號連接
器及線材
CPU & RAM
O:表示該有毒物質在該部件所有均質材料中的含量均在SJ/T 11363-2006標準規定的限量要求以下。
The quantity of poisonous or hazardous substances or elements found in each of the component's parts is
below the SJ/T 11363-2006-stipulated requirement.
X:表示該有毒物質至少在該部件的某一均質材料中的含量超出 SJ/T 11363-2006標準規定的限量要求。
The quantity of poisonous or hazardous substances or elements found in at least one of the component's
parts is beyond the SJ/T 11363-2006-stipulated requirement.
備註: 一、此產品所標示之環保使用期限,係指在一般正常使用狀況下。 二、上述部件物質中央處理
器、内存、硬碟、電源為選購品。The Environment Friendly Use Period as labeled on this product is
applicable under normal usage only
iv
TABLE OF CONTENTS
1.
Introduction ............................................................................................................................ 1
1.1
Features .......................................................................................................................... 1
1.2
Dimensions...................................................................................................................... 2
1.3
Packing List ...................................................................................................................... 2
1.4
Front Panel ...................................................................................................................... 3
1.5
Rear Panel ....................................................................................................................... 4
2. Connection and Installation .................................................................................................... 5
2.1
Storage Installation ......................................................................................................... 5
2.1.1 Storage Compatibility List ........................................................................................... 6
2.2
GPS Antenna Installation ................................................................................................ 7
2.3
RAM Installation.............................................................................................................. 8
2.4
DC Out Cable ................................................................................................................... 9
3. Jumpers and Connectors on the Motherboard .................................................................... 10
3.1
List of Jumpers .............................................................................................................. 12
3.1.1 Clear CMOS (CN10) ................................................................................................... 12
3.1.2 ATX/AT Selection (CN14) .......................................................................................... 12
3.1.3 COM1 Ring/ +5V/ +12V Selection (CN15) ................................................................. 12
3.1.4 CAN Bus UART/USB Selection (CN16) ....................................................................... 12
3.1.5 CAN Bus Program Firmware (CN18) ......................................................................... 13
3.2
List of Connectors ......................................................................................................... 14
3.2.1 Front Plane Connector (CN5) .................................................................................... 15
3.2.2 COM4 RS-232 Serial Port Connector (COM1) ........................................................... 15
3.2.3 COM3 RS-232 Serial Port Connector (COM2) ........................................................... 16
3.2.4 COM1 & COM2 RS-232/422/485 Serial Port Connector (COM3) ............................. 16
3.2.5 Digital I/O Connector (CN20) .................................................................................... 16
3.2.6 Power In & Remote Button (CN19)........................................................................... 17
3.2.7 CAN Bus 2.0B Connector (CN22)............................................................................... 17
3.2.8 Power on/off delay select (SW3) .............................................................................. 17
4. AMI BIOS Setup ..................................................................................................................... 18
4.1
System Test and Initialization ....................................................................................... 18
4.2
AMI BIOS Setup ............................................................................................................. 19
4.3
Setup Submenu: Main .................................................................................................. 19
4.4
Setup Submenu: Advanced ........................................................................................... 20
4.4.1 Advanced: CPU Configuration................................................................................... 20
4.4.2 Advanced: PCH-FW Configuration ............................................................................ 21
4.4.3 Advanced: SATA Drives ............................................................................................. 21
4.4.4 Advanced: Trusted Computing ................................................................................. 22
4.4.5 Advanced: Hardware Monitor .................................................................................. 23
4.4.6 Advanced: SIO Configuration .................................................................................... 23
4.4.6.1 SIO Configuration: Serial Port Configuration ........................................................ 24
4.4.6.2 SIO Configuration: Serial Port 1 Configuration ..................................................... 24
4.4.6.3 SIO Configuration: Serial Port 2 Configuration ..................................................... 25
4.4.6.4 SIO Configuration: Serial Port 3 Configuration ..................................................... 26
4.4.6.5 SIO Configuration: Serial Port 4 Configuration ..................................................... 26
4.4.6.6 SIO Configuration: Serial Port 5 Configuration ..................................................... 27
v
4.4.6.7 SIO Configuration: Serial Port 6 Configuration ..................................................... 28
4.4.7 Advanced: Digital IO Port Configuration................................................................... 28
4.4.8 Advanced: Power Management ............................................................................... 29
4.5
Setup Submenu: Chipset ............................................................................................... 30
4.5.1 Chipset: System Agent (SA) Configuration ............................................................... 30
4.5.1.1 System Agent (SA) Configuration: Graphics Configuration .................................. 31
4.6
Setup Submenu: Security .............................................................................................. 32
4.7
Setup Submenu: Boot ................................................................................................... 33
4.8
Setup submenu: Save & Exit ......................................................................................... 33
5. Specification .......................................................................................................................... 34
vi
eIVP5600 AI Mobile NVR
Chapter
1
1. Introduction
The eIVP5600 is one of EverFocus’ eIVP series AI mobile NVRs adopting Intel® 7th Gen. Core™ i5/i7
Processor and Movidius™ Myriad™ X AI core module.
The model supports up to 8 PoE ports with individual LAN chips. Featuring smart PoE functionality,
the eIVP5600 can remotely check or reboot the connected PoE devices if any of the PoE devices
are not working properly.
The eIVP5600 also supports wide operating temperature ranging from -20°C to 70°C and wide DC
range of DC 10-36V. It also features comprehensive storage options including two 2.5” HDD/SSD
bays (optional) and an mSATA slot, and 2 RS-232/422/485 ports for connecting to other devices.
The eIVP5600 is complied with the MIL-STD-810G standard for the utmost viability for vehicular
use. It supports onboard GPS, GLONASS and CAN bus. Besides, the model is also CE, FCC and RoHS
certified. The eIVP5600 AI mobile NVR carries everything you need for computing on the road.
eIVP5600 Model SKU
SKU1: eIVP5600-i5 (i5-7300U; PoE x 4)
SKU2: eIVP5600-i5 (i5-7300U; PoE x 8)
SKU3: eIVP5600-i7 (i7-7600U; PoE x 4)
SKU4: eIVP5600-i7 (i7-7600U; PoE x 8)
1.1 Features
•
•
•
•
•
•
•
•
•
•
In-vehicle network video recorder platform
Intel® 7th Gen. Core™ i5/i7 processor
260-pin DDR4 2133 MHz SODIMM x 2, up to 32GB (optional)
Intel® Integrated Graphics Engine supports 2 display outputs by HDMI x 1, DP x 1
Realtek® Ethernet x 10 ports (PoE x 8, GbE x 2)
Supports up to 8-channel IP cameras
Supports dual hot-swappable SSD storage (optional)
Intel Movidius AI core module (optional)
Supports CAN Bus 2.0B (optional)
CE, FCC, RoHS certified
1
eIVP5600 AI Mobile NVR
1.2 Dimensions
73.9
174.0
70.0
205.0
248.6
187.1
Unit: mm
1.3 Packing List
• NVR x 1
• DC Power Terminal Block x 1
• DC Out Cable x 1 (power supply for
cameras)
• mSATA Screw x 1
• CD x 1 (see Note 3)
Note:
1. Equipment configurations and supplied accessories vary by country. Please consult your
local EverFocus office or agents for more information. Please also keep the shipping carton
for possible future use.
2. Contact the shipper if any items appear to have been damaged in the shipping process.
3. The CD contains the User Manual and some Drivers for the system. If you can’t find the
required drivers from the CD, please go to our website for related drivers.
www.everfocus.com.tw
2
eIVP5600 AI Mobile NVR
1.4 Front Panel
1
2
3
4
5
6
2
7
8
No.
Name
Description
1
Power Button
Press the button to turn on or turn off the system.
2
Antenna
Connects the antenna to the mobile NVR for 3G / 4G / WiFi functions.
3
LED Indicator
HDD: When storage is reading/writing data, the LED will flashes green.
Wireless 1-3: Mini Card WLED (Slot1 w/LED1, Slot2 w/LED2, Slot3
w/LED3.
4
DP Port
DP display output.
5
PoE Ports
LAN3~8 with PoE function for connecting to the IP cameras.
6
USB3.0 Ports
USB3.0 ports.
7
Reset
Press the button to restart the system.
8
LAN/WAN
Two 10/100/1000 Base-Tx Ethernet ports for connecting to the
network.
3
eIVP5600 AI Mobile NVR
1.5 Rear Panel
1
8
9
2
3
4
5
10
6
7
1
11
12
No. Name
Description
1
Antenna
Connects the antenna to the mobile NVR for 3G / 4G / WiFi functions.
2
CAN Bus
CAN Bus 2.0B Connector.
3
SIM Card Slot
SIM Card slots.
4
HDMI Port
HDMI display output.
5
COM Ports
RS-232 ports.
6
Power Output
A total of 12VDC, 2A power supply to the connected cameras. Please refer
to 2.2 DC Power Out Cable.
7
Digital IO
Digital IO connector.
8
Audio Input
Connects to audio input devices, such as microphones. Note that the
microphones with a (built-in) amplifier and external power supply are
required.
9
Audio Output
Connects to an audio output device, such as speakers. Note that the
speakers with a (built-in) amplifier and external power supply are
required.
10
Fuse
Fuse Connector.
11
Power Input
Insert the supplied DC Power Terminal Block and then connect the
system to a DC 10-36V power source.
12
Remote Power Remote button.
4
eIVP5600 AI Mobile NVR
Chapter
2
2. Connection and Installation
2.1 Storage Installation
The eIVP5600 supports mSATA for storage.
To install the mSATA drive:
1.
Make sure the NVR is power-off.
2.
Unscrew the four screws on the bottom cover and then remove the bottom cover.
3.
Unscrew the 6 screws.
5
eIVP5600 AI Mobile NVR
4.
Lift up the case to remove the top cover.
5.
Turn the case to the other side and find the mSATA interface on the motherboard. Screw
your mSATA drive to the mSATA Interface using the supplied mSATA Screw.
mSATA Interface
6.
Screw back the top cover and bottom cover.
2.1.1 Storage Compatibility List
Please go to the product page (Download) on EverFocus’ Website www.everfocus.com.tw to see
the latest Storage Compatibility List. It’s recommended to use the storage models listed on the
Storage Compatibility List to ensure your storage devices are compatible.
6
eIVP5600 AI Mobile NVR
2.2 GPS Antenna Installation
The eIVP5600 supports onboard GPS. To enable the GPS function, connect a GPS Antenna to the
antenna port.
1.
Make sure the NVR is power-off.
2.
Unscrew the four screws on the bottom cover and then remove the bottom cover.
3.
Find the GPS connector on the motherboard. Connect one end of the RF cable to the GPS
connector and the other end to the Antenna port.
GPS Connector
Antenna Port
4.
Screw the GPS antenna to the Antenna port.
5.
Screw the bottom cover back to the model.
7
eIVP5600 AI Mobile NVR
2.3 RAM Installation
The eIVP5600 supports 260-pin DDR4 2133 MHz SODIMM x 2. You can install the RAM on the
DIMM port of the motherboard.
1.
Make sure the NVR is power-off.
2.
Unscrew the four screws on the bottom cover and then remove the bottom cover.
3.
Find the DIMM port on the motherboard and install the RAM.
4.
The second DIMM port is on the other side of the motherboard. To use the second DIMM
port, follow Step 3 and Step 4 in 2.1 Storage Installation to remove the Top Cover from the
model and turn the motherboard to the other side.
5.
Screw back the front cover and bottom cover to the model.
8
eIVP5600 AI Mobile NVR
2.4 DC Out Cable
The eIVP5600 provides a total of 12V/2A DC output with four sets of power output wires (+/-)
for the connected IP cameras.
Connect the supplied DC Out Cable to the DC Out port on the rear panel of the NVR.
- (black)
+ (black with white stripe)
9
eIVP5600 AI Mobile NVR
Chapter
3. Jumpers and Connectors on the Motherboard
Users can use the jumpers and connectors to configure different applications.
Component Side
10
3
eIVP5600 AI Mobile NVR
Solder Side
11
eIVP5600 AI Mobile NVR
3.1 List of Jumpers
You can refer to the jumpers listed as below to configure your application.
Label
Function
CN10
Clear CMOS
CN14
ATX/AT Selection
CH15
COM1 Ring/ +5V/ +12V Selection
CN16
CAN Bus UART/USB Selection
CN18
CAN Bus Program Firmware
3.1.1 Clear CMOS (CN10)
Pin
Function
1-2
Clear
2-3
Protected (Default)
3.1.2 ATX/AT Selection (CN14)
Pin
Function
1-2
ATX
2-3
AT (Default)
3.1.3 COM1 Ring/ +5V/ +12V Selection (CN15)
Pin
Function
1-2
+ 5V
3-4
Ring (Default)
5-6
+ 12V
3.1.4 CAN Bus UART/USB Selection (CN16)
Pin
Function
1-2
UART
2-3
USB (Default)
12
eIVP5600 AI Mobile NVR
3.1.5 CAN Bus Program Firmware (CN18)
Pin
Function
1-2
Protected (Default)
2-3
Program
13
eIVP5600 AI Mobile NVR
3.2 List of Connectors
You can refer to the connectors listed as below to configure your application.
Label
Function
SW1
Power Button
SW3
Software Reset
SW4
Power on/off delay selection
VGA1
CRT Port
SW1
Power Button
CN5
Front Panel Connector
CN3
Board to Board Connector
DP1
Display Port
CN4
LAN3~LAN6 (With PoE Function)
CN1
USB3 & USB4 Connector with LAN2 (10/100/1000 Base-Tx Ethernet)
Connector
CN2
USB1 & USB2 Connector with LAN1 (10/100/1000 Base-Tx Ethernet)
Connector
SW2
Software Reset
CN19
Power In & Remote Button
CN20
Digital I/O Connector
CN21
+ 12V Output
COM1
COM4 RS-232 Serial Port Connector
COM2
COM3 RS-232 Serial Port Connector
COM3
COM1 & COM2 RS-232/422/485 Serial Port Connector
HDMI1
HDMI
CN17
SIM Card (With SLOT2)
CN24
SIM Card (With SLOT3)
CN22
CAN Bus 2.0B Connector
AUDIO1
Audio Connector
CN11
Fuse Connector
SW3
Power on/off delay select
14
eIVP5600 AI Mobile NVR
DIMM1
DIMM2 Slot
DIMM2
DIMM1 Slot
SLOT1
Mini Card Connector (only USB) half size
SLOT2
Mini Card Connector (PCIe + USB) full size
SLOT3
Mini Card Connector (only USB) full size
MSATA1
Mini-SATA Connector
SATA1
Primary Serial ATA Connector
SATA2
Secondary Serial ATA Connector
LED4
SATA LED
LED1~LED3
Mini Card Wled
(SLOT1 w/LED1, SLOT2 w/LED2, SLOT3 w/LED3
3.2.1 Front Plane Connector (CN5)
Pin
Signal
Pin
Signal
1
PWR_SW#
2
FPANSWH#
3
GND
4
HWRST#
5
GND
6
FPANSWH#
3.2.2 COM4 RS-232 Serial Port Connector (COM1)
Pin
Signal
Pin
Signal
1
DCD
2
RXD
3
TXD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
9
RI
10
15
eIVP5600 AI Mobile NVR
3.2.3 COM3 RS-232 Serial Port Connector (COM2)
Pin
Signal
Pin
Signal
1
DCD
2
RXD
3
TXD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
9
RI
10
3.2.4 COM1 & COM2 RS-232/422/485 Serial Port Connector (COM3)
Pin
Signal
Pin
Signal
1
DCD
2
RXD (RS422 RX-)
3
TXD (RS485 Data/RS422 TX-)
4
DTR (RS422 RX+)
5
GND
6
DSR
7
RTS
8
CTS
9
RI
10
3.2.5 Digital I/O Connector (CN20)
1 3 5 7 9
2 4 6 8 10
Pin
Signal
Pin
Signal
1
GND
2
+GP_V
3
GPI0
4
GPO0
5
GPI1
6
GPO1
7
GPI2
8
GPO2
9
GPI3
10
GPO3
16
eIVP5600 AI Mobile NVR
3.2.6 Power In & Remote Button (CN19)
1 2 3
4 5 6
Pin
Signal
Pin
Signal
1
ACC
2
GND_PRI
3
PWR_IN
4
REMOTE_SW
5
GND
6
PS_ON#
3.2.7 CAN Bus 2.0B Connector (CN22)
1
2
Pin
Signal
Pin
Signal
1
CAN DATA +
2
CAN DATA -
3.2.8 Power on/off delay select (SW3)
Power On Delay
Switch Pin
Number
Control
Table
Power Off Day
6
7
8
Time (sec.)
5
4
3
Time (sec.)
off
off
off
5
off
off
off
180
off
off
on
10
off
off
on
300
off
on
off
15
off
on
off
900
off
on
on
30
off
on
on
1800
on
off
off
Null
on
off
off
2-Day
on
off
on
Null
on
off
on
Null
on
on
off
Null
on
on
off
Null
on
on
on
Null
on
on
on
Null
17
eIVP5600 AI Mobile NVR
Chapter
4
4. AMI BIOS Setup
4.1 System Test and Initialization
The board uses certain routines to perform testing and initialization. If an error, fatal or non-fatal,
is encountered, a few short beeps or an error message will be outputted. The board can usually
continue the boot up sequence with non-fatal errors.
The system configuration verification routines check the current system configuration against the
values stored in the CMOS memory. If they do not match, an error message will be outputted, in
which case you will need to run the BIOS setup program to set the configuration information in
memory.
There are three situations in which you will need to change the CMOS settings:
•
You are starting your system for the first time
•
You have changed your system’s hardware
•
The CMOS memory has lost power and the configuration information is erased
The system’s CMOS memory uses a backup battery for data retention, which is to be replaced
once emptied.
18
eIVP5600 AI Mobile NVR
4.2 AMI BIOS Setup
The AMI BIOS ROM has a pre-installed Setup program that allows users to modify basic system
configurations, which is stored in the batter y-backed CMOS RAM and BIOS NVRAM so that the
information is retained when the power is turned off.
To enter BIOS Setup, press <Del> or <F2> immediately while your computer is powering up.
The function for each interface can be found below.
•
Main – Date and time can be set here. Press <Tab> to switch between date elements
•
Advanced – Enable/ Disable boot option for legacy network devices
•
Chipset – For hosting bridge parameters
•
Boot – Enable/ Disable quiet Boot Option
•
Security – The setup administrator password can be set here
•
Save & Exit –Save your changes and exit the program
4.3 Setup Submenu: Main
Press the “Delete” key to enter the setup page.
19
eIVP5600 AI Mobile NVR
4.4 Setup Submenu: Advanced
4.4.1 Advanced: CPU Configuration
Options summary:
Active Processor Cores
All
1
Number of cores to enable in each processor package.
Hyper-Threading
Disabled
Enabled
Enabled for Windows XP and Linux (OS optimized for Hyper-Threading Technology) and Disabled for
other OS (OS not optimized for Hyper-Threading Technology).
20
eIVP5600 AI Mobile NVR
4.4.2 Advanced: PCH-FW Configuration
Options summary:
ME FW Image Re-Flash
Disabled
Enabled
Enable/Disable Me FW Image Re-Flash function.
4.4.3 Advanced: SATA Drives
Options summary:
SATA Controller(s)
Disabled
Enabled
Enable/Disable SATA Device.
Hot Plug
Disabled
Enabled
Designates this port as Hot Pluggable.
21
eIVP5600 AI Mobile NVR
4.4.4 Advanced: Trusted Computing
Options summary:
Security Device Support
Disabled
Enabled
Enables or Disables BIOS support for security device. O.S. will not show Security Device. TCG EFI
protocol and INT1A interface will not be available.
TPM State
Disabled
Enabled
Enable/Disable Security Device. NOTE: Your Computer will reboot during restart in order to change
State of the Device.
Pending operation
None
TPM Clear
Schedule an Operation for the Security Device. NOTE: Your Computer will reboot during restart in
order to change State of Security Device.
Device Select
TPM 1.2
TPM 2.0
Auto
TPM1.2 will restrict support to TPM 1.2 devices, TPM 2.0 will restrict support to TPM 2.0 devices,
Auto will support both with the default set to TPM 2.0 devices if not found, TPM 1.2 devices will
be enumerated..
22
eIVP5600 AI Mobile NVR
4.4.5 Advanced: Hardware Monitor
4.4.6 Advanced: SIO Configuration
23
eIVP5600 AI Mobile NVR
4.4.6.1 SIO Configuration: Serial Port Configuration
4.4.6.2 SIO Configuration: Serial Port 1 Configuration
24
eIVP5600 AI Mobile NVR
Options summary:
Use This Device
Disabled
Enabled
Enable or Disable this Logical Device.
Possible:
Use Automatic Settings
IO=2F8h; IRQ=3;
IO=3F8h; IRQ=4;
Allows user to change Device's Resource settings. New settings will be reflected on
This Setup Page after System restarts.
Mode
RS232
RS422
RS485
UART RS232, 422, 485 selection.
4.4.6.3 SIO Configuration: Serial Port 2 Configuration
Options summary:
Use This Device
Disabled
Enabled
Enable or Disable this Logical Device.
Possible:
Use Automatic Settings
IO=2F8h; IRQ=3;
IO=3F8h; IRQ=4;
Allows user to change Device's Resource settings. New settings will be reflected on this Setup Page after
System restarts.
Mode
RS232
RS422
RS485
UART RS232, 422, 485 selection.
25
eIVP5600 AI Mobile NVR
4.4.6.4 SIO Configuration: Serial Port 3 Configuration
Options summary:
Use This Device
Disabled
Enabled
Enable or Disable this Logical Device.
Possible:
Use Automatic Settings
IO=2F8h; IRQ=3;
IO=3F8h; IRQ=4;
Allows user to change Device's Resource settings. New settings will be reflected on this Setup Page after
System restarts.
4.4.6.5 SIO Configuration: Serial Port 4 Configuration
26
eIVP5600 AI Mobile NVR
Options summary:
Use This Device
Disabled
Enabled
Enable or Disable this Logical Device.
Possible:
Use Automatic Settings
IO=2F8h; IRQ=3;
IO=3F8h; IRQ=4;
Allows user to change Device's Resource settings. New settings will be reflected on this Setup Page after
System restarts.
4.4.6.6 SIO Configuration: Serial Port 5 Configuration
Options summary:
Use This Device
Disabled
Enabled
Enable or Disable this Logical Device.
Possible:
Use Automatic Settings
IO=2F8h; IRQ=3;
IO=3F8h; IRQ=4;
Allows user to change Device's Resource settings. New settings will be reflected on this Setup Page after
System restarts.
27
eIVP5600 AI Mobile NVR
4.4.6.7 SIO Configuration: Serial Port 6 Configuration
Options summary:
Use This Device
Disabled
Enabled
Enable or Disable this Logical Device.
Possible:
Use Automatic Settings
IO=2F8h; IRQ=3;
IO=3F8h; IRQ=4;
Allows user to change Device's Resource settings. New settings will be reflected on this Setup Page after
System restarts.
4.4.7 Advanced: Digital IO Port Configuration
28
eIVP5600 AI Mobile NVR
Options summary:
DIO Port5~8
Output
Input
Set DIO as Input or Output.
Output Level
Low
High
Set output level when DIO pin is output.
4.4.8 Advanced: Power Management
Options summary:
Power Mode
ATX Type
AT Type
Select Power Supply Mode.
Restore AC Power Loss
Power Off
Power On
Last State
Select AC power state when power is re-applied after a power failure.
29
eIVP5600 AI Mobile NVR
4.5 Setup Submenu: Chipset
4.5.1 Chipset: System Agent (SA) Configuration
30
eIVP5600 AI Mobile NVR
4.5.1.1 System Agent (SA) Configuration: Graphics Configuration
Options summary:
VT-d
Enabled
Disabled
VT-d capability.
Primary Display
Auto
IGFX
PEG
Select which of IGFX/PEG/PCI Graphics device should be Primary Display Or select
SG for Switchable Gfx.
Primary IGFX Boot Display
VBIOS Default
HDMI
DP
Select the Video Device which will be activated during POST. This has no effect if external graphics present.
Secondary boot display selection will appear based on your selection. VGA modes will be supported only on
primary display.
31
eIVP5600 AI Mobile NVR
4.6 Setup Submenu: Security
Change User/Administrator Password
You can set a User Password once an Administrator Password is set. The password will be required
during boot up, or when the user enters the Setup utility. Please Note that a User Password does
not provide access to many of the features in the Setup utility.
Select the password you wish to set, press Enter to open a dialog box to enter your password (you
can enter no more than six letters or numbers). Press Enter to confirm your entry, after which you
will be prompted to retype your password for a final confirmation. Press Enter again after you
have retyped it correctly.
Removing the Password
Highlight this item and type in the current password. At the next dialog box press Enter to disable
password protection.
32
eIVP5600 AI Mobile NVR
4.7 Setup Submenu: Boot
Options summary:
Quite Boot
Disabled
Enabled
Enables or disables Quiet Boot option.
Launch PXE ROM
Controls the execution of UEFI and Legacy PXE OpROM
4.8 Setup submenu: Save & Exit
33
Disabled
Enabled
eIVP5600 AI Mobile NVR
Chapter
5
5. Specification
Model No.
System
Video
Audio
Recording
Storage
Processor
Main Memory
Format
Video Input
Video Output
Audio Input
Audio Output
Format
Resolution
Internal HDD Bay
Removable SSD
RAID
CE / Cfast / mSATA
Ethernet
Network
Alarm
Wi-Fi
3G / 4G
GPS / G-Sensor
Alarm Input
Alarm Output
Interface
Front I/O Panel
eIVP5600
Intel® 7th Gen. Core™ i5/i7 Processor
Up to 32GB, DDR4 260-pin SODIMM (optional)
H.264/H.265
IP camera x 8
HDMI x 1, DP x 1
Mic-in x 1
Line-out x 1
H.264/H.265
1920 x 1080 at 30fps (NTSC) / 25fps (PAL)
2.5" HDD x 2 (optional)
Hot swappable 2.5’’ SSD x 2 (project base) via extension module
0/1
mSATA slot x 1
RTL8111E 10/100/1000 based; GbE port x 2; PoE port x 4 (up to
8) (IEEE 802.3 at/af)
* Every 4 PoE ports shares 60W of power budget
Supported
Supported
On board (GPS/GLONASS), G-Sensor
Digital input x 4 (wet/dry contact with Isolation Protection
3,000 VDC)
Digital output x 4 (compatible 5 V/TTL, 31mA max. per channel)
Power button x 1
3G/4G/WIFI LED x 3
USB3.0 x 4
GbE port (RJ-45) x 2
PoE LAN x 4 (IEEE 802.3 at/af), max. 8 ports
DP x 1
Reset button x 1
34
eIVP5600 AI Mobile NVR
Rear I/O Panel
Interface
Expansion Slot
General
Power Supply
Dimensions (W x D
X H)
Gross Weight
Operating
Storage
Storage Humidity
Vibration/Shock
Certification
DC-In power x 1
Remote power x 1
8-bit DIO x 1
4ch digital input (wet/dry contact with Isolation Protection
3,000 VDC)
4ch digital output (compatible 5 V/TTL, 31mA max. per channel)
DC 12V/1A output x 1
RS-232/422/485 x 2
HDMI x 1
CanBus connector x 1
Audio line-out x 1
Mic-in x 1
SIM slot x 2
Mini-Card slot x 3 (USB2.0 x 2 + PCIe & USB 2.0 x 1)
Built-in CAN 2.0B x 1
DC 10-36V, with ignition pin
6.85’’ x 8.07” x 2.76” / 174mm x 205mm x 70mm (without
bracket)
5.7lb (2.6kg)
-4°F ~ 158°F (-20°C ~ 70°C); Project base: -40°C ~ 85°C
-40°F ~ 185°F (-40°C ~ 85°C)
10%~80% @40°C, non-condensing
MIL-STD-810G
CE & FCC Class A, RoHS
Note: All specifications are subject to change without notice.
35
EverFocus Electronics Corp.
EverFocus Taiwan:
2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng
Dist., New Taipei City 222, Taiwan
TEL: +886 2 2662 2338
FAX: +886 2 2662 3632
www.everfocus.com.tw
marketing@everfocus.com.tw
EverFocus China - Shenzhen:
3F, Building 7, Longcheng Industrial Park, No.39,
Longguan No.7 Road, Dalang Street, Longhua,
Shenzhen, Guangdong, China
TEL: +86 755 2765 1313
FAX: +86 755 2765 0337
www.everfocus.com.cn
marketing@everfocus.com.cn
EverFocus USA - California:
1801 Highland Avenue, Unit A, Duarte, CA 91010,
USA
TEL: +1 626 844 8888
FAX: +1 626 844 8838
www.everfocus.com
sales@everfocus.com
EverFocus Japan:
3F, Kuramochi, Building II, 2-2-3 KotoBashi,Sumida-Ku, Tokyo, 130-0022, Japan
TEL: +81 3 5625 8188
FAX: +81 3 5625 8189
www.everfocus.co.jp
info@everfocus.co.jp
Your EverFocus product is designed and
manufactured with high quality materials
and components which can be recycled
and reused.
This symbol means that electrical and
electronic equipment, at their end-of-life,
should be disposed of separately from
your household waste.
Please, dispose of this equipment at your
local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Ihr EverFocus Produkt wurde entwickelt
und hergestellt mit qualitativ
hochwertigen Materialien und
Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass elektrische
und elektronische Geräte am Ende ihrer
Nutzungsdauer vom Hausmüll getrennt
entsorgt werden sollen.
Bitte entsorgen Sie dieses Gerät bei Ihrer
örtlichen kommunalen Sammelstelle oder
im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!
P/N: 4605EIVP503001A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising