EverFocus | eIVP5600 | Owner Manual | Everfocus eIVP5600 Owner Manual

Everfocus eIVP5600 Owner Manual
AiO NVR Software
All-in-One software for eIVP series models
User’s Manual
Copyright © EverFocus Electronics Corp.
Release Date: October 2019
EVERFOCUS ELECTRONICS CORPORATION
AiO NVR Software
User’s Manual
 1995-2019 EverFocus Electronics Corp.
www.everfocus.com.tw
Disclaimer
All the images including product pictures or screen shots in this document are for example only. The
images may vary depending on the product and software version. Information contained in this document
is subject to change without notice.
Copyright
All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form
or by any means without written permission of the EverFocus Electronics Corporation.
TABLE OF CONTENTS
1.
2.
Introduction ............................................................................................................................ 1
Getting Started........................................................................................................................ 2
2.1
Startup Wizard ................................................................................................................ 3
2.2
General Operation on the OSD Menu .......................................................................... 10
2.3
Live View Window......................................................................................................... 12
2.3.1 Dynamic Status Bar ................................................................................................... 15
2.4
Live Channel Tool Bar.................................................................................................... 17
2.4.1 Digital Zoom (PIP)...................................................................................................... 18
2.4.2 PTZ Control Panel ...................................................................................................... 19
2.4.2.1 PTZ Control Panel .................................................................................................. 19
2.4.2.2 Preset Setting ........................................................................................................ 20
2.5
Live Alarm Panel............................................................................................................ 22
3. OSD Menu ............................................................................................................................. 27
3.1
Channel ......................................................................................................................... 28
3.1.1 Channel ..................................................................................................................... 28
3.1.1.1 IP Channels............................................................................................................ 28
3.1.1.1.1 Adding PoE IP Cameras ................................................................................. 30
3.1.1.1.2 Auto Add IP Cameras .................................................................................... 31
3.1.1.1.3 Manually Add IP Cameras ............................................................................. 32
3.1.1.2 Manage Protocol................................................................................................... 33
3.1.2 Live ............................................................................................................................ 34
3.1.3 Image Control............................................................................................................ 36
3.1.4 PTZ............................................................................................................................. 38
3.1.5 Privacy Mask ............................................................................................................. 39
3.1.6 Motion....................................................................................................................... 40
3.1.7 Intelligent .................................................................................................................. 41
3.1.7.1 Perimeter Intrusion ............................................................................................... 41
3.1.7.1.1 Configuring Perimeter Intrusion Areas ......................................................... 42
3.1.7.2 Line Crossing ......................................................................................................... 43
3.1.7.2.1 Configuring Line Crossing Detection Lines.................................................... 44
3.1.7.3 Foreign/Missing Object ......................................................................................... 45
3.1.7.3.1 Configuring Foreign/Missing Areas............................................................... 46
3.1.7.4 Pedestrian Detection ............................................................................................ 47
3.1.7.4.1 Configuring Pedestrian Detection Area ........................................................ 48
3.1.7.5 Face Detection ...................................................................................................... 49
3.1.7.5.1 Configuring Face Detection Area .................................................................. 50
3.1.7.5.2 Configuring Face Recognition Settings ......................................................... 51
3.1.7.6 Loitering Detection ............................................................................................... 53
3.1.7.7 Cross-Counting Detection ..................................................................................... 54
3.1.8.6.1 Configuring Cross-Counting Detection Line .................................................. 55
3.1.7.8 Sound Detection ................................................................................................... 56
ii
3.1.7.9 Tamper Detection ................................................................................................. 57
3.1.7.10 Record Schedule ................................................................................................. 58
3.1.7.11 Cross-Counting Analysis ...................................................................................... 59
3.1.7.12 Driver Fatigue & Distraction ............................................................................... 60
3.2
Record ........................................................................................................................... 62
3.2.1 Stream ....................................................................................................................... 62
3.2.1.1 Main Stream.......................................................................................................... 62
3.2.1.2 Sub Stream ............................................................................................................ 64
3.2.1.3 Mobile Stream ...................................................................................................... 65
3.2.2 Record ....................................................................................................................... 66
3.2.2.1 Record ................................................................................................................... 66
3.2.2.2 Record Schedule ................................................................................................... 67
3.2.3 Snapshot ................................................................................................................... 68
3.2.3.1 Snapshot ............................................................................................................... 68
3.2.3.2 Snap. Schedule ...................................................................................................... 69
3.3
Alarm ............................................................................................................................. 70
3.3.1 Motion....................................................................................................................... 70
3.3.2 IO ............................................................................................................................... 72
3.3.3 Intelligent Alarm ....................................................................................................... 74
3.3.3.1 IVS Alarm Settings ................................................................................................. 74
3.3.3.2 Face Recognition Alarm Settings .......................................................................... 76
3.3.3.3 Statistics ................................................................................................................ 81
3.3.4 PTZ Linkage ............................................................................................................... 82
3.3.5 Exception................................................................................................................... 83
3.3.6 Alarm Schedule ......................................................................................................... 84
3.3.7 GPS ............................................................................................................................ 85
3.3.8 G-Sensor .................................................................................................................... 86
3.4
Network ........................................................................................................................ 87
3.4.1 General ...................................................................................................................... 87
3.4.1.1 General.................................................................................................................. 87
3.4.1.2 PPPoE .................................................................................................................... 88
3.4.1.3 WiFi ....................................................................................................................... 89
3.4.1.4 3G/4G .................................................................................................................... 90
3.4.1.5 Xfleet ..................................................................................................................... 91
3.4.1.6 Port Configuration ................................................................................................ 92
3.4.2 DDNS ......................................................................................................................... 93
3.4.3 Email.......................................................................................................................... 96
3.4.3.1 Email Configuration .............................................................................................. 96
3.4.3.2 Email Schedule ...................................................................................................... 97
3.4.4 FTP ............................................................................................................................. 98
3.4.4.1 FTP......................................................................................................................... 98
3.4.4.2 FTP Schedule ......................................................................................................... 99
3.4.5 IP Filter .................................................................................................................... 100
iii
3.5
Device .......................................................................................................................... 101
3.5.1 Disk .......................................................................................................................... 101
3.5.1.1 Disk ...................................................................................................................... 101
3.5.1.2 Disk Group........................................................................................................... 103
3.5.1.3 S.M.A.R.T ............................................................................................................. 104
3.5.2 Cloud ....................................................................................................................... 105
3.6
Layout.......................................................................................................................... 107
3.7
Playback ...................................................................................................................... 108
3.7.1 General Operation .................................................................................................. 108
3.7.2 Playback Control Panel ........................................................................................... 109
3.7.2.1 Full Screen on Playback Window ........................................................................ 111
3.7.2.2 Backup Video Clips .............................................................................................. 113
3.7.3 Search Mode ........................................................................................................... 114
3.7.3.1 General................................................................................................................ 114
3.7.3.2 Events .................................................................................................................. 115
3.7.3.3 Time-Period......................................................................................................... 119
3.7.3.4 Smart ................................................................................................................... 121
3.7.3.5 Tag ....................................................................................................................... 123
3.7.3.6 External File......................................................................................................... 125
3.7.3.7 Snapshot ............................................................................................................. 126
3.7.3.8 Intelligent ............................................................................................................ 130
3.8
Express ........................................................................................................................ 131
3.8.1 Quick Playback ........................................................................................................ 131
3.8.2 Stream Switch ......................................................................................................... 131
3.8.3 Preview Policy ......................................................................................................... 131
3.9
System ......................................................................................................................... 132
3.9.1 General .................................................................................................................... 132
3.9.1.1 General................................................................................................................ 132
3.9.1.2 Date and Time ..................................................................................................... 133
3.9.1.3 Video Output....................................................................................................... 135
3.9.2 User Account ........................................................................................................... 136
3.9.3 Maintenance ........................................................................................................... 138
3.9.3.1 Log ....................................................................................................................... 138
3.9.3.2 Load Default ........................................................................................................ 140
3.9.3.3 Upgrade............................................................................................................... 140
3.9.3.4 System Parameter ............................................................................................... 141
3.9.3.5 Auto Reboot ........................................................................................................ 141
3.9.4 IPCam Maintain ....................................................................................................... 142
3.9.4.1 Upgrade............................................................................................................... 142
3.9.4.2 Load Default ........................................................................................................ 142
3.9.4.3 Reboot IPC........................................................................................................... 143
3.9.4.4 System Parameter ............................................................................................... 143
3.9.5 System Info ............................................................................................................. 144
iv
3.9.5.1 System Info ......................................................................................................... 144
3.9.5.1.1 Performing the P2P Function ...................................................................... 144
3.9.5.2 Channel Info ........................................................................................................ 146
3.9.5.3 Record Info .......................................................................................................... 147
3.9.5.4 Network Info ....................................................................................................... 147
3.10 Exit............................................................................................................................... 148
v
AiO NVR Software
Chapter
1
1. Introduction
The AiO is an EverFocus in-house designed NVR software that can run on both Intel and NVIDIA
platforms. Except for the basic functions that a regular NVR should have, including live view
monitoring, video recordings and playback, the AiO also features AI functions such as Face
Recognition, People Counting, Loitering Detection and so on.
The AiO NVR software supports all EverFocus eIVP series standard and vehicle industrial PCs, and
can be pre-installed inside the eIVP models upon customer’s request.
1
AiO NVR Software
Chapter
2
2. Getting Started
After turning on the power of your eIVP model, the system will start initializing the AiO NVR
software. When the initialization process is done, it’s required to set up a password for the
administrator account immediately in order to protect your privacy.
Language: Select an OSD language.
Device ID: Input the device ID. The default ID is 000000. For more details about the Device ID,
please refer to 3.9.1.1 General.
New Admin name: Optionally input a name if you want to set up a name of the administrator
account.
Password Strength: Displays the security strength of the setup password.
New Admin Password: Set up a password of the administrator account. The password must be a
combination of at least 8 characters (alphabetic, numeric, or special characters).
Confirm Password: Enter the password again.
Enable Unlock Pattern: If you want to login the system with a pattern lock, select Enable from the
drop-down list and then click the Draw button to draw a pattern. To disable the Unlock Pattern
function, please refer to User Edit in 3.9.2 User Account.
Apply: Click to save the settings.
2
AiO NVR Software
After clicking the Apply button, the below Unlock page appears. Input the User Name, Password
and then click Unlock.
2.1 Startup Wizard
The Startup Wizard will guide you through some basic settings for the NVR software. Please follow
the on-screen instructions to proceed.
Note: If you don’t want to run the startup Wizard to make any settings when you restart the eIVP
model next time, you can go to OSD Menu > System > General and then uncheck the Start
wizard function.
1. Click the Start Wizard button to start with the startup wizard.
3
AiO NVR Software
2. Configure the Network settings. Click Next to proceed. For more details on network settings,
please refer to 3.4 Network.
3. Configure the Date/Time settings. You can also configure the NTP and DST settings. Click Next
to proceed.
【Date and Time】
Date: Click on the calendar icon to set the system date.
Time: Click to set the system time.
Date Format: Select a date format from the drop-down list.
Time Format: Select a time format from the drop-down list.
Time Zone: Select a time zone of your region.
4
AiO NVR Software
【NTP】
NTP stands for Network Time Protocol. This feature allows you to synchronize the NVR
software date and time automatically over the Internet with the NTP server. Please ensure the
NVR software has been connected to the Internet before enabling the NTP function.
To enable NTP, check Enable NTP, select an NTP server from the drop-down list or input one of
your region. Click Update Now.
【DST】
DST stands for Daylight Saving Time.
Enable DST: Check the box to enable the Daylight Saving Time (DST) function.
Time Offset: Select the amount of time to offset for DST.
Daylight Saving Time: Choose to set up the daylight saving time in weeks or in days.
Start Time/End Time: Set the start time and end time for DST.
4. Add IP cameras to the NVR software. By default, the system will automatically detect the IP
cameras connected to the PoE ports of the NVR software. Please refer to 3.1.1.1 IP Channels
for more details.
5
AiO NVR Software
5. Configure the Disk settings. For the first time use HDD or a new HDD, users have to format the
HDD before use. Select the HDDs you want to format by checking the checkbox in the No
column and then click the Format HDD button. You can also setup to overwrite the HDD. Click
Next to proceed.
Overwrite: Select Auto to enable the overwrite function; Off to disable the overwrite function.
If Auto is selected, the NVR software will overwrite the oldest files on the HDD when HDD is
full. If Off is selected, please check the HDD status regularly, to make sure the HDD is not full.
The 1/3/7/14/30/90 Days stands for the last number of days to keep in the HDD. For example,
if 3 Days is selected, the last 3 days recordings will be kept in the HDD.
Format HDD: The first time use HDDs have to be formatted before you can use it. Select the
desired HDDs and then click the Format HDD button to format the selected HDDs. Note that
only the HDDs with “Unformat” status displayed in the State column are required to format or
the recording function will not work. WARNING: This will effectively ERASE the ENTIRE hard
disk!! Please backup the data from HDDs before formatting the HDDs.
Note:
1. Only the HDDs with “OK” in the State column can perform the recording function. If not,
format the HDDs before start using the recording function.
2. The “Free Time” on the HDD list indicates the remaining time for the HDD to record
based on the pre-setup resolution, streaming and fps.
Record on eSATA: If you have connected an external eSATA storage device to the NVR
software, you can enable the eSATA backup storage function.
6
AiO NVR Software
6. The NVR software will apply the resolution best suit the connected monitor. If you want to
change the output resolution, select an output resolution that matches your monitor. Click the
Apply button. Click Next to proceed.
7. Mobile information. You can scan the QR code with EverFocus eFVMS App installed on your
mobile device to add the eIVP model to your app and then remotely access the NVR software
(please refer to 3.9.5.1 System Info for more details). Click Next to proceed.
7
AiO NVR Software
8. The setup information through this wizard will be displayed on the Summary page. Click Finish
to close the wizard.
Note: You can check “Do not show this window next time” if you do not want to run the
startup Wizard to make any settings when you restart the NVR software next time.
9. After clicking the Finish button, the system will enter the Live View window (refer to 2.3 Live
View Window).
8
AiO NVR Software
10. To start using the NVR software, click any function and the Unlock window appears. Input the
password of the NVR software and then click the Unlock button to unlock the screen, the OSD
Setup menu appears. You can start using the NVR software. Please refer to 3. OSD Menu for
more details.
Channel
Record
Layout
Playback
Alarm
Express
9
Network
Device
System
Exit
AiO NVR Software
2.2 General Operation on the OSD Menu
Channel
Record
Layout
Playback
Alarm
Express
Network
Device
System
Exit
【OSD Menu】
1. On the Live View window, right click the mouse, the OSD Menu appears.
2. Click on any icons to enter the setup menus.
3. To exit the OSD menu, right click the mouse. You can also exit each sub menu by right
clicking the mouse.
【Text Box】
Click on the box and an on-screen keyboard will appear.
【On-Screen Keyboard】
Click on a button to input that character.
Switch to capital letters
Confirm the selection
Delete the letter
backwards
Move to the left or right
Enter a space
10
AiO NVR Software
【Drop-Down Box】
Click on the down arrow to see all selections, then directly click on an option to select it.
【Check Box】
Click on the box to enable it (checked) or disable it (unchecked).
【Button】
Click the button to execute the function.
【Slider】
Slide the bar to the left or right for adjusting the value.
11
AiO NVR Software
2.3 Live View Window
The AiO NVR software supports Standard and Vehicle eIVP models. The Standard and Vehicle
models are designed with different Live View Window in order to cater to the application
environment.
Main View of eIVP Standard Models
1
2
3
4
5
6
7
8
9
10
6
11
No
Name
1
Channel
Number
2
Live Channel
Tool Bar
Left click any channel can display its Live Channel Tool Bar to perform
functions including Manual Record, manual Snapshot, Quick Playback
and etc.. Please refer to 2.4 Live Channel Tool Bar for more details.
3
Quick Add
Click to open the Quick Add menu to add IP cameras. Please refer to
3.1.1.1 IP Channels for more details.
4
System Date
and Time
Displays system date and time. To change system date and time, go to
OSD Menu > System > General > Date and Time.
5
Channel State
Displays the status of channel connection.
Description
The system will automatically display the channel number once the
channel has been applied with an IP camera. To configure the channel
number (name), please refer to Alias in 3.1.1.1.3 Manually Add IP
Cameras.
12
AiO NVR Software
The Status Icons displayed on the screen are designed to alert users
when any of the following situations occur:
6
Channel recording
Motion event is detected
External I/O alarm is triggered
Status Icons
S
S
HDD error
HDD full
HDD unformatted
HDD is ready
Intelligent event is triggered and on recording
Intelligent event is triggered.
7
Drag Channel
Icon
You can drag and drop a channel to the desired position on the layout.
Click on a channel and hold it, a Drag Channel icon will display. Drag
and drop the channel to the desired channel position on the layout.
8
Live Alarm
Panel
This panel is designed to display the real-time alarm in thumbnails. You
can quickly check or play back the alarm using this panel. Please refer
to 2.5 Live Alarm Panel for more details.
Move your mouse cursor to the left or right edge of the screen, the
9
10
Layout Page
Icons
Edit
Next icon or Previous icon
will appear. Click the Previous / Next
icon to turn to the previous / next layout pages. For example, for 16CH
device, if you select 9-Division, click the next layout page icon (on the
right side) will display the next 9-division layout with channel 10-16.
When IP camera connection failed, the edit icon
will appear. Click
to open the Edit IP Camera Profile menu to edit the IP camera
parameters. Please refer to 3.1.1.1 IP Channels for more details.
Double-click on a channel can display the channel in full screen. To exit
the full screen mode, double-click on the channel again.
11
Live Channel
In full screen mode, you can:
•
Left-click to bring up the Live Channel Tool Bar. Please refer to
2.4 Live Channel Tool Bar for more details.
•
Scroll the mouse to zoom in or zoom out the images, and then
use your mouse to drag the image to the desired positions to spot
on a specific area.
13
AiO NVR Software
Main View of eIVP Vehicle Models
Compare with the Standard model, the Live View window of the Vehicle model features a
bottom bar used to display dynamic vehicle status to cater to the vehicle application. Except for
the bottom bar, all the other functions and configurations can be referred to the Standard model.
1
CH01
CH02
CH03
CH04
PTZ
4
41°24'12.2N 2°10'26.5E
B
No
2
G-Sensor (1, 14, 5)
Name
R
GPS 4G WiFi
80 KM/Hr 4260 RPM
2019/09/05 16:15
3
Description
The Status Icons displayed on each channel are designed to alert users
when any of the following situations occur:
Channel recording
Motion event is detected
External I/O alarm is triggered
S Intelligent event is triggered and on recording
S Intelligent event is triggered.
The HDD Status Icons are designed to alert users when any of the
following situations occur:
1
Status Icons
2
HDD Status
Icons
3
Dynamic Status
Bar
You can use the Dynamic Status Bar to enter the OSD setup menu or
view the dynamic system status. Please refer to 2.3.1 Dynamic Status
Bar for more details
GPS / G-Sensor
If your device supports GPS or G-Sensor function. The GPS coordinates
and G-Sensor data will be displayed on the Live View window. To
enable displaying the data, please refer to 3.3.7 GPS and 3.3.8 GSensor.
4
HDD error
HDD full
HDD unformatted
HDD is ready
14
AiO NVR Software
2.3.1
Dynamic Status Bar
The Dynamic Status Bar only appears on the bottom of the Live View window of eIVP Vehicle
Models. Users can use this bar to enter the OSD setup menu or view the dynamic system status.
Note that to enable the status icons displayed on the bar, users will have to connect the relevant
devices to the eIVP models and then configure the relevant settings on the NVR software, such as
wireless network settings, event and alarm settings. Please refer to the below instructions.
1
B
R
2
3
GPS 4G WiFi
4
5
6
80 KM/Hr 4260 RPM
8
7
2019/09/05 16:15
9
10
No
Name
Description
1
Turn Left / Turn
Right
Displaying the Turn Left or Turn Right icon when a driver is making a
left turn or right turn while driving. See Note 1.
2
Brake
Displaying the Brake icon when a driver is making a Brake while
driving. See Note 1.
3
Reverse
Displaying the Reverse icon when a driver is reversing car. See Note 1.
4
GPS
Displaying the GPS connection status. When GPS connection is
established, the GPS icon will be displayed. See Note 2.
5
3G / 4G
Displaying the 3G/4G wireless network connection status. When
connected to 3G/4G, the 3G/4G icon will be displayed. See Note 3.
6
WiFi
Displaying the WiFi network connection status. When connected to
WiFi, the WiFi icon will be displayed. When WiFi is off, an Off icon will
be displayed. When there is no WiFi network, an NA icon will be
display. See Note 4.
7
Vehicle Speed
When connected to GPS, the vehicle speed will be displayed here.
8
RPM
Displaying the RPM data from the vehicle. See Note 1.
9
System
Date/Time
Displays system date and time. To configure, please refer to 3.9.1.2
Date and Time.
10
Menu
Click to enter the OSD Menu. Please refer to 3. OSD Menu.
15
AiO NVR Software
Note:
1.
To get the vehicle data in order to display the status icon on the Dynamic Status Bar,
including Turn Left, Turn Right, Reverse, Brake or RPM, please connect your eIVP model to
the vehicle through CAN Bus.
2.
To display GPS connection status, users will have to pre-connect the GPS Antenna to the
antenna port on the eIVP model. For eIVP models without onboard GPS, please connect a
GPS module to the mini card slot on the motherboard inside your eIVP model. To
configure GPS settings, please refer to 3.3.7 GPS.
3.
To display 3G/4G connection status, users will have to connect a 3G or 4G module to the
mini card slot on the motherboard inside your eIVP model and connect the Antenna to
the antenna port, and finally insert a SIM card to the SIM card slot. To configure 3G/4G
network settings, please refer to 3.4.1.4 3G/4G.
To display WiFi connection status, users will have to connect a WiFi module to the mini
card slot on the motherboard inside your eIVP model and connect the Antenna to the
antenna port. To configure WiFi network settings, please refer to 3.4.1.3 WiFi.
4.
16
AiO NVR Software
2.4 Live Channel Tool Bar
You can left-click any channel on the Live View Window to bring up its Live Channel Tool Bar.
Note that the Live Channel Tool Bar is only available for Standard model.
1
No
2
3
4
5
6
7
8
9
10
11
Name
Description
1
Manual Record
Click the button to start manual recording. During the process of
manual recording, the icon will display in red. Click the button again to
stop manual recording.
2
Click to take a snapshot of the channel. You can then using the
Playback panel to playback the snapshot images. Please refer to
Manual Snapshot
3.7.3.7 Snapshot. To configure the snapshot parameters or set up the
snapshot schedule, please refer to 3.2.3 Snapshot.
Click to playback the latest 5 minutes recording of this channel. Click X
to exit the Quick Playback mode. To configure the quick playback start
time, please refer to 3.8.1 Quick Playback.
3
Quick Playback
4
PTZ
5
Zoom
6
Image Settings
7
Stream Switch
8
Add Customized
Tag
You can add a tag of the selected time to this channel. Input a tag
name and then click Save. To search for the tags, go to Playback > Tag,
please refer to 3.7.3.5 Tag.
9
Face Recognition
Statistics
This icon will only appear when a face-recognition-supported IP
camera is connected to the channel. Move the mouse cursor to the
icon can display the number of faces recognized on this channel
during the selected time. Please refer to 2.5 Live Alarm Panel.
10
Audio
Click to turn on or turn off the audio, or adjust audio volume.
11
Manual Alarm
Click to manually trigger alarm output of the channel.
This icon will only appear when a PTZ camera is connected to the
channel. Click to bring up the PTZ Control window. Please refer to
2.4.2 PTZ Control Panel for more details.
Click to start the digital zoom function. Please refer to 2.4.1 Digital
Zoom (PIP) for more details.
Click to bring up the Color Setting window. You can adjust the Hue,
Brightness, Contrast and Saturation for each channel individually.
Click to switch between HD and SD stream displayed on the live view
channel. To adjust the HD (main stream), SD (sub stream) settings,
please refer to 3.2.1.1 Main Stream and 3.2.1.2 Sub Stream.
17
AiO NVR Software
2.4.1
Digital Zoom (PIP)
You can use the Digital Zoom function to have a close-up view on the desired locations of a
live channel.
Live full screen channel
Preview Window
Navigation Box
To perform the digital zoom function:
1. On the Live View window, left-click on a channel to display its Live Channel Tool Bar and
then click the Zoom icon, the channel will be displayed in full screen with a Preview
Window on the bottom-right corner of the screen.
2. Scroll the mouse upward/downward to zoom in/out, a Navigation Box will be displayed on
the Preview Window.
3. Drag the Navigation Box and drop it to the position where you want to have a close-up
view.
4. To exit the Digital Zoom mode, right-click the mouse.
5. To return to the Live View window, double-click on the Live full screen channel.
Note: You can also perform the Digital Zoom function by scrolling the mouse directly on the
Live View to zoom in or zoom out the images, and then drag the live view image to the
desired positions to spot on a specific area.
18
AiO NVR Software
2.4.2
PTZ Control Panel
With the PTZ Control Panel, you can control the connected PTZ cameras.
On the Live View window, select a PTZ camera by clicking on the channel, the selected
channel will be highlighted with a red frame. Left-click on the channel to display its Live
Channel Tool Bar and then click the PTZ icon to bring up the PTZ Control panel.
For Vehicle model, click the PTZ icon on the OSD menu to bring up the PTZ Control Panel.
PTZ
2.4.2.1 PTZ Control Panel
You can use the PTZ Control panel to control the connected PTZ camera.
Note that before using this function, you have to connect the PTZ cameras to the NVR
software and configure the related PTZ settings. Please refer to 3.1.4 PTZ.
PTZ Control Panel
Select a channel
Direction Buttons / Auto Pan Button
Operation Speed
Adjusting Zoom, Focus, IRIS
Channel: Click to select a PTZ camera you want to control.
PTZ: Click PTZ to enter the PTZ Control panel.
19
AiO NVR Software
Direction Buttons: Click the direction buttons to force the PTZ camera to turn to the
direction.
Auto Pan
function.
: Click to start the Auto Pan (360°) function. Click again to stop the Auto Pan
Speed: Switch the bar to the left or right to adjust the operation speed.
Zoom: Click + or – to zoom in or zoom out.
Focus: Click + or – to focus near or focus far.
Iris: Click + or – to adjust the Iris.
2.4.2.2 Preset Setting
Click Preset to enter the Preset Setting panel. On this panel, you can set up Preset positions,
perform the Go to Preset function and also perform the Tour function.
Preset Setting Panel
Select a channel
Direction Buttons / Auto Pan Button
Preset / Tour Setting
Preset List
To set up Preset Points:
1.
Click on the No. input box and input a preset number (1-255).
2.
Click on the Time input box to set up a dwell time for this preset number.
3.
Use the direction buttons or Zoom/Focus/Iris buttons to search for the location for this
preset number.
4.
Click the
button to save this preset point and then jump to the next preset number
for configuration. Follow Step 2-3 to set up multiple preset points.
5.
After setting up the preset points, click the Save button to save the settings.
6.
To clear the setup preset points, select a preset number in the No. input box and then
click the Clear button . Or you can also click the Clear button of a specific preset
number on the Preset List.
20
AiO NVR Software
To perform the Go to Preset Point function:
1.
Set up the preset points in advance.
2.
Input a preset number (1-255) in the No. input box, and then click the Go button
3.
You can also click the Go button
to the selected preset point.
.
of a specific preset number on the Preset List to go
To perform the Tour function:
1. Set up the preset points in advance.
2. Click the Start Tour button, the PTZ camera will start cruising based on the pre-configured
preset points with the dwell time.
3. To stop the Tour function, click the Stop Tour button.
21
AiO NVR Software
2.5 Live Alarm Panel
The Live Alarm Panel is designed to display the real-time alarm in thumbnails. You can quickly
check or play back the alarm using this panel. Note that the Live Alarm Panel is only available for
Standard model.
Live Alarm Panel supports the following alarm functions. For the alarm functions to work, you
have to pre-configure the required alarm settings:
•
Face Recognition
•
Loitering Detection
•
Motion Detection
•
IO Alarm
•
IVS Alarm (Perimeter Intrusion, Object Detection, Pedestrian Detection, Line-Crossing,
Face Recognition, Cross-Counting Detection, Sound Detection, Tamper Detection)
Live Alarm Panel
22
AiO NVR Software
Here we take Face Recognition for example:
1.
Ensure the face-recognition-supported IP cameras have been connected to the NVR software.
2.
To enable the Face Recognition function, go to OSD > Channel > Intelligent > Face Detection.
3.
Check the Switch checkbox to enable the Face Recognition function of this channel.
4.
Click the Setup icon
settings, click Save.
to configure the Face Recognition settings. After configuring the
Channel: Select a channel to configure the settings.
Snapshot Mode: Select a Snapshot Mode.
23
AiO NVR Software

Realtime: System will take two snapshot images. One is when alarm triggered. The other
will be an optimal image that system recognized.

Optimal: System will take one snapshot images that is recognized as the optimal one.

Interval: Select this mode to further set up the Snapshot Quantity and Snapshot Interval.
-
Snapshot Quantity: Select the number of snapshot image to take per set up interval.
-
Snapshot Interval: Set up an interval to take the snapshot images.
Snapshot Number: Select a recognition mode.



Custom Mode: Select this mode to take the frontal face image only. To view the default
parameters, select Customize and then click the Custom Mode Default button.
Min Pixel: Select this mode to apply the minimum parameters of the orientation angles
(Roll, Pitch, Yaw) of the faces toward camera, Picture Quality and Quick Mode. To view
the default parameters, select Customize and then click the Min Pixel Default button.
Customize: Select this mode and then apply the orientation angles (Roll, Pitch, Yaw) of
the faces toward camera, Picture Quality and Quick Mode.
-
Roll Range: Adjust the rotation angle (0-180).
-
Pitch Range: Adjust the horizontal angle (0-180).
-
Yaw Range: Adjust the vertical angle (0-180).
-
Picture Quality: Adjust the quality of the face snapshot images. The more the value,
the better the image quality.
-
Quick Mode: Set up the maximum recognition pixel size within a 1080p image.
-
Custom Mode Default: Click to display the default parameters of the Custom Mode.
-
Min Pixel Default: Click to display the default parameters of the Min Pixel.
Detection Range: Select a detection area.

Full Screen: Select Full Screen to detect the area of whole image.

Customize: Select Customize and resize the area by dragging the red dots at the edge.
1
24
AiO NVR Software
5.
To display Face Recognition thumbnails on the Live Alarm Panel, go to OSD > Alarm >
Intelligent > Face Recognition.
a. Configure the face group settings. Please refer to 3.3.3.2 Face Recognition Alarm Settings
for more details.
b. Click the Setting icon
in the Alarm column of each group. Enable the Show Thumbnail
function so the Face Recognition thumbnail will be displayed on the Live Alarm Panel.
c. Click the Setting icon
in the Alarm Schedule column of each group. Configure the
alarm schedule time and then click the Apply button.
25
AiO NVR Software
6.
The Face Recognition configuration is complete. Go to the Live View page and when there are
faces detected, the Face Recognition thumbnails will be displayed on the Live Alarm Panel.
Click to pin or unpin the Live Alarm Panel.
Click to hide or display the thumbnails.
Click to display the below window to:
Select the Alarm functions you want to
display on the Live Alarm Panel and select
the Channels. Click Apply to save the
settings.
Displays the number of detected faces within a time range.
To modify the time range, click the Setting button on the
upper-right corner and click Statistics.
When system detects faces edited in the Groups:
1. The detected face will be displayed on the left. The
faces stored in the system database will be
displayed on the right.
2. The name, channel and time will be displayed on the
top. The similarity and the belonged group will be
displayed on the bottom.
3. Double-click on the thumbnail can start playing
back.
Select a time range to display the number
of detected faces from Face Recognition.
When system detects unknown faces:
1. The detected face will be displayed.
2. Click on this thumbnail can start playing back.
26
AiO NVR Software
Chapter
3
3. OSD Menu
You can use the OSD Menu to configure system settings.
For Standard model, right-click the mouse to bring up the OSD Menu.
Channel
Record
Layout
Playback
Alarm
Express
Network
Device
System
Exit
For Vehicle model, click the Menu button on the lower-right corner of the screen to bring up the
OSD Menu.
CH01
CH02
CH03
PTZ
41°24'12.2N 2°10'26.5E
G-Sensor (1, 14, 5)
B
R
GPS 4G WiFi
80 KM/Hr 4260 RPM
2019/09/05 16:15
27
AiO NVR Software
3.1 Channel
In this section, you can configure the settings including IP cameras, live view display, PTZ setup,
motion setup, Intelligent functions and more.
3.1.1
Channel
3.1.1.1 IP Channels
Search: Click to search for the IP cameras connected to the local network. The searched IP
cameras will be displayed on the upper list.
Add: Click to manually add IP camera on the local network one by one to the NVR software.
The added IP camera will be displayed on the lower list. Please refer to 3.1.1.1.3 Manually Add
IP Cameras for more details.
Add All: Click to automatically add the IP cameras on the local network to the NVR software
based on the supported number of IP camera of your device. Please refer to 3.1.1.1.2 Auto
Add IP Cameras for more details.
Camera Search: The added IP camera would not be able to connect to the NVR software if its
IP address is not on the same network segment with the NVR software. Therefore, you can
use this function to reassign an IP address to all added IP cameras with the same network
segment as NVR software’s.
Channel Delete: On the added IP cameras list, check the IP camera boxes and then click the
Channel Delete button to delete the selected IP cameras from the list.
Manual Mode: Click to enter the Manual Mode to add the IP cameras from the local network
to the NVR software. If you are in the Manual Mode and you want to add some IP cameras
28
AiO NVR Software
connected to the eIVP model via PoE ports, you can click the Edit button to switch the channel
mode to Auto Mode, the system will automatically detect the PoE channels. However, if you
are in the Auto Mode, clicking the Manual Mode button will switch all the available channels
to Manual Mode, and then you can connect the IP cameras from the local network.
Auto Mode: Click to enter the Auto Mode for the system to automatically detect the IP
cameras connected to the PoE ports of the eIVP model.
Note that if you have already added some IP cameras from the local network in the Manual
Mode, clicking the Auto Mode button will delete all the connected IP cameras from the local
network (see message window below). You can click the Edit button to switch the channel to
Auto Mode to add the IP cameras connected to PoE ports of the eIVP model.
EPOE: Click this button and all the PoE ports will be limited with 10Mbps bandwidth output.
Auto POE: Click this button to disable the EPOE function.
Default Password: Click to bring-up the Set-up Protocol Default Password page. You can
configure the default password for various protocols. When adding IP cameras to the NVR
software, the NVR software will automatically apply the Default Password to the IP cameras
based on their protocol. To configure Protocol settings, please refer to 3.1.1.2 Manage
Protocol.
29
AiO NVR Software
You can also use the buttons on the Added IP Camera list to perform the functions:
PoE: This represents the IP camera is connected to the PoE port of the eIVP model.
Delete: Click
to delete the IP camera.
Add: Click
to bring up the Add IP Camera window to add an IP camera from the local
network. Please refer to 3.1.1.1.3 Manually Add IP Cameras for more details.
Edit: Click
Modify: Click
to edit IP camera profile.
to modify IP camera settings.
State: Shows the status of the IP camera.
indicates connection failed.
indicates
connection succeeded. Click the
can pop-up a live window of the IP camera.
3.1.1.1.1 Adding PoE IP Cameras
10.10.25.152
EBN1240
10.10.25.153
EHN2540
10.10.25.154
EZN1540
To add IP cameras connected to the PoE ports of the eIVP model:
1.
Ensure the PoE IP cameras have been connected to the PoE ports of the eIVP model.
2.
Click the Auto Mode button, the system will automatically detect the IP cameras
connected to the PoE ports and the Live Display icon
will be displayed in the State
column.
30
AiO NVR Software
3.
If you still want to add some IP cameras via local network:
a. Click the Edit button
down list. Click OK.
and then select Manual Mode from the Switch Mode drop-
b. Now you can click the Add button
to add an IP camera from the local network.
Please refer to 3.1.1.1.3 Manually Add IP Cameras.
3.1.1.1.2 Auto Add IP Cameras
To automatically add IP cameras connected to the local network to NVR software:
1. Click the Search button to search for the IP cameras connected to the local network.
2. Click the Auto Add All button. The NVR software will automatically add the IP cameras to
each channel based on the No. order.
31
AiO NVR Software
3.1.1.1.3 Manually Add IP Cameras
1. Click Add to bring-up the Add IP Camera page.
2. Click Search to search for the IP cameras on the network. Note that the IP cameras that
have been added to the NVR software will not be displayed.
3. To select an IP camera, click an IP camera on the list, the clicked IP camera will be
highlighted with a blue background.
4. Configure the IP camera settings at the lower section.
IP Address/Domain: Input the IP address or domain name of the IP camera.
Alias: Input a channel name for the IP camera. The channel name will be displayed on the
upper-left corner of the channel.
Position: Select a position to display the camera name on the live channel.
Port: Port of the IP camera.
Protocol: Select a protocol. For Custom protocol, please refer to 3.1.1.2 Manage Protocol.
User Name: Input the user name of the IP camera.
Password: Input the password of the IP camera.
Camera Mode: Select a camera mode. Options include Auto, Normal and Fisheye.
5. Click Add and the IP camera will be added to the channel.
32
AiO NVR Software
3.1.1.2 Manage Protocol
On this page, you can edit RTSP (Custom 1-16) protocol for IP camera connection.
Custom Protocol: Select a custom RTSP protocol profile from the drop-down list to be
configured. Up to 16 profiles can be configured.
Protocol Name: Input a name for this RTSP protocol profile.
Stream Type: Indicates Main Stream and Sub Stream are supported. You can separately
configure the Main Stream and Sub Stream settings below.
Enable Sub Stream: Check the Sub Stream checkbox if you want to enable sub stream for
this RTSP protocol.
• Type: Select RTSP.
• Port: Input the RTSP port of your IP camera. Keep 554 as the RTSP port.
• Resources Path: Input the RTSP URL syntax in the box. For example:
rtsp://[IP Address]:[Port]/ip[A]/[B]
rtsp://192.168.31.33:554/ip01/0
* IP Address: The IP address of the eIVP model
* A: Channel number. 01 (ch1), 02 (ch2), and so on
* B: Stream Type: 0 (main stream), 1 (sub stream)
Click Apply to save the settings or Default to apply the default setting.
33
AiO NVR Software
3.1.2
Live
You can configure IP camera Live display settings or image quality.
Channel: Displays the channel number.
Setup: Click
to enter the setup page.
Select a channel
Optionally input a channel name
Select a date format.
Select a time format.
Select a video signal type.
Select to display channel name on the live channel
Select to display system time on the live channel
Adjust the value
Image Setting:
Adjust Hue, Brightness, Contrast, Saturation
Click to restore the Image Setting parameters to default value
Click to apply all value to the camera.
34
AiO NVR Software
Covert: Select to covert the camera stream on the live view. The channel will be black-out on
the Live Window, however, the system will still record the streams.
Channel Name: Optionally change the channel name.
Show Name: Check the box to display the channel name on the live channel.
Date Format: For supported IP cameras only. Select a date format.
Time Format: For supported IP cameras only. Select a time format.
Record Time: Check the box to enable recording the time to the recording files.
Signal Format: For supported IP cameras only. Select a system format (50Hz or 60Hz).
Click Apply to save the settings.
35
AiO NVR Software
3.1.3
Image Control
You can configure the image settings for supported IP cameras.
Channel: Displays the channel number.
Setup: Click
to enter the setup page.
Channel: Select a channel number.
Day/Night Mode: Select a Day/Night mode.
• GPIO Auto: Select GPIO Auto for the camera to
automatically switch to day or night mode. You can
further set up a Delay Switch (s) time (second) in the
below field.
• Color Mode: Select Color Mode for the camera to
display color images.
• Black White Mode: Select Black White Mode for the
camera to display B/W images.
• Schedule (B/W): Select Schedule (B/W) for the camera
to display B/W images during the setup time range.
Please select the Start Time and End Time in the
below field.
Delay Switch (s): This function can only be activated if you
select GPIO Auto for the Day/Night Mode. Set up a delay
switch time (seconds) for the camera to auto switch between
day and night modes.
IR-LED: Select On to turn on IR LEDs; select Off to turn off IRLED; select Auto for the camera to automatically turn on / off
the IR-LED based on the light sensor on the IP camera.
Flip: Check the box to enable the Flip function. The image will
be rotated vertically around a horizontal axis.
Mirror: Check the box to enable the Mirror function. The
image will be rotated horizontally around a vertical axis.
Hallway Mode: Check the box to enable the Hallway display
function (16:9).
Angle Rotate: Select a rotate angle.
36
AiO NVR Software
Backlight: Select Enable to enable the BLC (Backlight Compensation) function.
BLC Level: Adjust the level for the BLC function.
BLC Area: Select an area to apply the BLC function.
3D Noise Reduction:
• Auto: Select Auto for the camera to automatically turn on the 3DNR function.
• Manual: Select to turn on the 3DNR function based on the setup Level.
• Disable: Select to disable the 3DNR function.
WDR: Select Enable to enable the WDR function and then you will have to adjust a Level for
the WDR function.
AGC: If you select Manual in the Shutter field, set up the AGC for the camera. The lower the
AGC level, the lower the video signal and the noise.
White Balance:
• Auto: Select for the camera to automatically adjust the white balance.
• Manual: Select to adjust the Red, Green, Blue values yourself.
• Indoor: Select Indoor if your camera is installed in an indoor environment.
Shutter:
• Auto: Select for the camera to automatically adjust the Shutter.
• Manual: Select to manually adjust the shutter speed. Select a speed in the Time Exposure
field. Also set up the AGC in the AGC field above.
Time Exposure: If you select Auto in the Shutter field, the camera will automatically apply a
max. shutter speed. If you select Manual in the Shutter field, select a shutter speed from the
drop-down list.
Defog Mode:
• Auto: Select Auto for the camera to automatically turn on the Defog function.
• Manual: Select to turn on the Defog function based on the setup Level.
• Disable: Select to disable the Defog function.
Click Default to restore to default settings.
37
AiO NVR Software
3.1.4
PTZ
Please connect the PTZ cameras to the NVR software and then configure the below PTZ
settings. After configuring the PTZ settings, you can start using the PTZ Control panel to
control the PTZ camera. Please refer to 2.4.2.1 PTZ Control Panel.
Channel: Displays the channel number.
Signal Type: Analog for analog PTZ cameras; Digital for IP PTZ cameras.
Protocol: Select a communication protocol between the PTZ camera and NVR software.
Baudrate: This field is to set the speed at which is used to transmit instruction or information
from the NVR software to the PTZ camera.
Data Bit / Stop Bit: The information between the NVR software and PTZ camera is sent in
individual packages. The Data Bit indicates the number of bits sent, while the End Bit indicates
the end of the package and the beginning of the next (information) package.
Parity: For error check. Refer to the documentation of your PTZ camera to configure this setting
Address: Input the ID address of the PTZ camera. Note this address should match the one set up
on the PTZ camera.
Copy: You can apply the same configurations from one channel to other channels.
To perform the Copy function:
1. Click the Copy button, the Parameter Copy window appears.
2. Select a channel from the Source Channel drop-down list and then select the
parameters you would like to apply to other channels.
3. Select the desired channels from the Target Channel field.
4. Click the Copy button, the selected channels will be applied with the same parameters
as the source channel.
Click Apply to save the settings or Default to apply the default setting.
38
AiO NVR Software
3.1.5
Privacy Mask
The Privacy Mask can block out sensitive areas from view. This feature is useful when users
don’t want the sensitive information visible. Up to four Privacy Masks can be configured per
channel.
To configure privacy masks:
1. Select a channel from the Channel drop-down list.
2. Select Enable Privacy Zone to enable the function.
3. Select the areas (masks) to be configured. The selected areas will be displayed on the
preview image. Up to 4 areas are available.
4. To resize the area, click and drag the bottom-right corner of the rectangle to resize. To drag
an area to another location, click and drag the number to relocate the area.
Click and drag to relocate
Click and drag to resize
5. Click the Apply button to save the settings.
39
AiO NVR Software
3.1.6
Motion
You can configure the motion settings and motion event notifications on this page.
To configure the Motion Detection settings:
1. Click
to bring-up the Motion Area Setup page.
a. Select a channel from the Channel drop-down list.
b. Select Enable from the Switch drop-down list to enable motion detection function.
c. To set up motion detection sensitivity level, select a value from the Sensitivity dropdown list. The higher the value the higher the sensitivity.
d. By default, the whole areas are marked in red. The red blocks represents the areas are
applied with the motion detection function. You can click the mouse and drag it to
draw multiple areas. To clear a certain area, use the same method to draw on the
same area again, the motion area will be erased.
e. To save the settings, right-click the mouse to return to the Motion Setup page and
then click Apply to save the settings.
2. To further set up the motion event notifications, click the Alarm button to enter the
Motion alarm setup page (please refer to 3.3.1 Motion).
3. If you want to activate the motion recording function, you need to configure the recording
schedule. Please refer to 3.2.2.2 Record Schedule.
40
AiO NVR Software
3.1.7
Intelligent
The optional intelligent functions, including Perimeter Intrusion Detection, Line Crossing
Detection, Foreign/Missing Object Detection, Pedestrian Detection, Face Detection, Cross
Counting, Sound Detection and Tamper Detection.
3.1.7.1 Perimeter Intrusion
When objects (people, vehicle or other objects) enter in or out of a pre-defined region, the
Perimeter Intrusion Detection event will be triggered. You can configure some event actions
like event recording, Email alert or pop-up full screen when an event is triggered.
To configure the Perimeter Intrusion settings:
1. Check the Switch checkbox to enable the function of the channel.
2. Select a Sensitivity value from the drop-down list. The larger the value, the higher the
sensitivity.
3. In the Scene field, select Indoor or Outdoor based on the location where your camera is
installed.
4. In the Setup field, click
to set up the detection areas. Please refer to 3.1.7.1.1
Configuring Perimeter Intrusion Areas for more details.
5. Click the Apply button to save the settings.
6. To further set up the alarm notifications, click the Alarm button to enter the Alarm setup
page. Please refer to 3.3.3 Intelligent Alarm.
7. If you want to activate the intelligent recording function, you need to configure the
recording schedule. Please refer to 3.1.7.10 Record Schedule.
41
AiO NVR Software
3.1.7.1.1 Configuring Perimeter Intrusion Areas
Click the Setup button
to enter the Area setup page.
1. Select 1 from the Rule Number drop-down list to configure the first area.
2. Click the Rule Switch button to enable this rule.
3. Define a type for this rule:
AB: Detects movement from A to B.
BA: Detects movement from B to A.
AB: Detects both movements from A to B and from B to A.
4. To draw an area:
a. Use your mouse to click 4 points to draw a rectangle shape. The shape should be
convex. Concave shape is not allowed.
b. If you want to move the area to other position or re-size the area, select the area by
checking the red box on the upper-left corner of the area, the borders of the area will
change to red color. Drag and drop the area to a desired position. Drag the red dots
at the edge of the area can re-size the area.
1
c. Click the Save button to save the settings.
d. Follow the steps above to configure more areas. Up to 4 areas can be configured.
e. You can click the Remove All button to remove all the areas. To remove a certain
area, select the area by checking the red box on the upper-left corner of the area,
and then click the Remove button.
Note: The detection areas should not be too narrow or small in order to enhance the
detection rate.
5. To return to the Perimeter Intrusion setup page, right-click the mouse.
42
AiO NVR Software
3.1.7.2 Line Crossing
When objects (people, vehicle or other objects) cross a pre-defined line, the Line Crossing
Detection event will be triggered. You can configure some event actions like event recording,
Email alert or pop-up full screen when an event is triggered.
To configure the Line Crossing settings:
1. Check the Switch checkbox to enable the function of the channel.
2. Select a Sensitivity value from the drop-down list. The larger the value, the higher the
sensitivity.
3. In the Scene field, select Indoor or Outdoor based on the location where your camera is
installed.
4. In the Setup field, click
to set up the detection lines. Please refer to 3.1.7.2.1
Configuring Line Crossing Detection Lines for more details.
5. Click the Apply button to save the settings.
6. To further set up the alarm notifications, click the Alarm button to enter the Alarm setup
page. Please refer to 3.3.3 Intelligent Alarm.
7. If you want to activate the intelligent recording function, you need to configure the
recording schedule. Please refer to 4.1.7.10 Record Schedule.
43
AiO NVR Software
3.1.7.2.1 Configuring Line Crossing Detection Lines
Click the Setup button to enter the Line setup page.
1. Select 1 from the Rule Number drop-down list to configure the first line.
2. Click the Rule Switch button to enable this rule.
3. Define a type for this rule:
AB: Detects movement from A to B.
BA: Detects movement from B to A.
AB: Detects both movements from A to B and from B to A.
4. To draw a line:
a. Use your mouse to click 2 points to draw a line.
b. If you want to move the line to other position or re-draw the line, select the line by
checking the red box on the upper-side of the line, the line will change to red color.
Drag and drop the line to a desired position. Drag the red dots of the line can re-size
the line.
1
c. Click the Save button to save the settings.
d. Follow the steps above to configure more lines. Up to 4 lines can be configured.
e. You can click the Remove All button to remove all the lines. To remove a certain line,
select the line by checking the red box on the upper-side of the line, and then click
the Remove button.
Note: The detection lines should not be too short in order to enhance the detection
rate.
5. To return to the Line Crossing setup page, right-click the mouse.
44
AiO NVR Software
3.1.7.3 Foreign/Missing Object
When camera detects foreign (unattended) or missing objects in a pre-defined area, the
Foreign/Missing Object event will be triggered. You can configure some event actions like
event recording, Email alert or pop-up full screen when an event is triggered.
To configure the Foreign/Missing Object settings:
1. Check the Switch checkbox to enable the function of the channel.
2. Select a Sensitivity value from the drop-down list. The larger the value, the higher the
sensitivity.
3. In the Scene field, select Indoor or Outdoor based on the location where your camera is
installed.
4. In the Setup field, click
to set up the detection areas. Please refer to 3.1.7.3.1
Configuring Foreign/Missing Areas for more details.
5. Click the Apply button to save the settings.
6. To further set up the alarm notifications, click the Alarm button to enter the Alarm setup
page. Please refer to 3.3.3 Intelligent Alarm.
7. If you want to activate the intelligent recording function, you need to configure the
recording schedule. Please refer to 4.1.7.10 Record Schedule.
45
AiO NVR Software
3.1.7.3.1 Configuring Foreign/Missing Areas
Click the Setup button
to enter the Area setup page.
Missing & Foreign
1. Select 1 from the Rule Number drop-down list to configure the first area.
2. Click the Rule Switch button to enable this rule.
3. Define a type for this rule.
Foreign: NVR software will only detect the unattended objects.
Missing: NVR software will only detect the missing objects.
Missing & Foreign: NVR software will detect both missing objects and unattended
objects.
4. To draw an area:
a. Use your mouse to click 4 points to draw a rectangle shape. The shape should be
convex. Concave shape is not allowed.
b. If you want to move the area to other position or re-size the area, select the area by
checking the red box on the upper-left corner of the area, the borders of the area will
change to red color. Drag and drop the area to a desired position. Drag the red dots
at the edge of the area can re-size the area.
1
c. Click the Save button to save the settings.
d. Follow the steps above to configure more areas. Up to 4 areas can be configured.
e. You can click the Remove All button to remove all the areas. To remove a certain
area, select the area by checking the red box on the upper-left corner of the area,
and then click the Remove button.
Note: For foreign/missing object, please draw an area slightly larger than or equal to
the detected object, and the detected object cannot be covered.
1 Lost & Legacy
5. To return to the Foreign/Missing Object setup page, right-click the mouse.
46
AiO NVR Software
3.1.7.4 Pedestrian Detection
When camera detects moving people in a pre-defined area, the Pedestrian Detection event
will be triggered. You can configure some event actions like event recording, Email alert or
pop-up full screen when an event is triggered.
To configure the Pedestrian Detection settings:
1. Check the Switch checkbox to enable the function of the channel.
2. In the Level field, select among Far, Middle and Near. Far level is recommended to
detect objects in long distance. Near level is recommended to detect objects in short
distance.
3. In the Scene field, select Indoor or Outdoor based on the location where your camera is
installed.
4. In the Setup field, click
to set up the detection areas. Please refer to 3.1.7.4.1
Configuring Pedestrian Detection Area for more details.
5. Click the Apply button to save the settings.
6. To further set up the alarm notifications, click the Alarm button to enter the Alarm setup
page. Please refer to 3.3.3 Intelligent Alarm.
7. If you want to activate the intelligent recording function, you need to configure the
recording schedule. Please refer to 3.1.7.10 Record Schedule.
47
AiO NVR Software
3.1.7.4.1 Configuring Pedestrian Detection Area
Click the Setup button
to enter the Area setup page.
1. Select 1 from the Rule Number drop-down list to configure the area.
2. Click the Rule Switch button to enable this rule.
3. Define a type for this rule. Only Normal type is available.
4. To draw an area:
a. Use your mouse to click 4 points to draw a rectangle shape. The shape should be
convex. Concave shape is not allowed.
b. If you want to move the area to other position or re-size the area, select the area by
checking the red box on the upper-left corner of the area, the borders of the area will
change to red color. Drag and drop the area to a desired position. Drag the red dots
at the edge of the area can re-size the area.
1
c. Click the Save button to save the settings.
d. You can click the Remove All button to remove all the areas. To remove a certain
area, select the area by checking the red box on the upper-left corner of the area,
and then click the Remove button.
Note: The detection areas should not be too narrow or small in order to enhance the
detection rate. The whole target object (people) should be inside the area.
5. To return to the Pedestrian Detection setup page, right-click the mouse.
48
AiO NVR Software
3.1.7.5 Face Detection
This page can be used to setup Face Recognition functions. Note that for Face Recognition
function to work, a face-recognition-supported IP camera should be connected to the eIVP
model. When camera detects faces of moving people, the Face Recognition event will be
triggered. You can configure some event actions like event recording, Email alert or pop-up
full screen when an event is triggered.
To configure the Face Recognition settings (face-recognition-supported IP camera required):
1. Check the Switch checkbox to enable the function of the channel.
2. In the Setup field, click
to set up the face recognition settings. Please refer to
3.1.7.5.2 Configuring Face Recognition Settings for more details.
3. Click the Apply button to save the settings.
4. To further set up the alarm notifications, click the Alarm button to enter the Alarm setup
page. Please refer to 3.3.3.2 Face Recognition Alarm Settings.
5. If you want to activate the intelligent recording function, you need to configure the
recording schedule. Please refer to 3.1.7.10 Record Schedule.
49
AiO NVR Software
3.1.7.5.1 Configuring Face Detection Area
Click the Setup button
to enter the Area setup page.
1. Select 1 from the Rule Number drop-down list to configure the area.
2. Select Enable from the Rule Switch drop-down list to enable this rule.
3. Define a type for this rule. Only Normal type is available.
4. To draw an area:
a. Use your mouse to click 4 points to draw a rectangle shape. The shape should be
convex. Concave shape is not allowed.
b. If you want to move the area to other position or re-size the area, select the area by
checking the red box on the upper-left corner of the area, the borders of the area will
change to red color. Drag and drop the area to a desired position. Drag the red dots
at the edge of the area can re-size the area.
1
c. Click the Save button to save the settings.
d. You can click the Remove All button to remove all the areas. To remove a certain
area, select the area by checking the red box on the upper-left corner of the area,
and then click the Remove button.
Note: The configured areas should include the whole front face.
5. To return to the Face Detection setup page, right-click the mouse.
50
AiO NVR Software
3.1.7.5.2 Configuring Face Recognition Settings
Click the Setup button
1.
to enter the setup page.
Configure the below settings.
Channel: Select a channel to configure the settings.
Snapshot Mode: Select a Snapshot Mode.

Realtime: System will take two snapshot images. One is when alarm triggered. The other
will be an optimal image that system recognized.

Optimal: System will take one snapshot images that is recognized as the optimal one.

Interval: Select this mode to further set up the Snapshot Quantity and Snapshot Interval.
-
Snapshot Quantity: Select the number of snapshot image to take per set up interval.
-
Snapshot Interval: Set up an interval to take the snapshot images.
Snapshot Number: Select a recognition mode.



Custom Mode: Select this mode to take the frontal face image only. To view the default
parameters, select Customize and then click the Custom Mode Default button.
Min Pixel: Select this mode to apply the minimum parameters of the orientation angles
(Roll, Pitch, Yaw) of the faces toward camera, Picture Quality and Quick Mode. To view
the default parameters, select Customize and then click the Min Pixel Default button.
Customize: Select this mode and then apply the orientation angles (Roll, Pitch, Yaw) of
the faces toward camera, Picture Quality and Quick Mode.
-
Roll Range: Adjust the rotation angle (0-180).
-
Pitch Range: Adjust the horizontal angle (0-180).
-
Yaw Range: Adjust the vertical angle (0-180).
-
Picture Quality: Adjust the quality of the face snapshot images. The more the value,
the better the image quality.
51
AiO NVR Software
-
Quick Mode: Set up the maximum recognition pixel size within a 1080p image.
-
Custom Mode Default: Click to display the default parameters of the Custom Mode.
-
Min Pixel Default: Click to display the default parameters of the Min Pixel.
Detection Range: Select a detection area.

Full Screen: Select Full Screen to detect the area of whole image.

Customize: Select Customize and resize the area by dragging the red dots at the edge.
1
2.
Click Save to save the settings.
52
AiO NVR Software
3.1.7.6 Loitering Detection
This page can be used to setup Loitering Detection function. Loitering detection can be used
for advanced intrusion detection, such as loitering alarms and identifying a person entering a
specific area. When a person loiters in an area within a pre-defined time, the alarm will be
triggered.
To configure the Loitering Detection settings:
1. Check the Switch checkbox to enable the function of the channel.
2. In the Setup field, click
to set up the detection area.
3. Click the Apply button to save the settings. Now you can see the Loitering Detection on
the live channel.
4. To further set up the alarm notifications, click the Alarm button to enter the Alarm setup
page.
5. If you want to activate the intelligent recording function, you need to configure the
recording schedule. Please refer to 3.1.7.10 Record Schedule.
When the NVR software detects a person
entering the pre-defined area, a green frame
will be displayed. The red frame represents
the person has been loitered in this area more
than the pre-defined time. The ID number will
be shown to indicate this person is the 208th
detected person, and loitering time will be
counted. The system will further track the
person, and the tracks will be displayed with
blue color.
53
AiO NVR Software
3.1.7.7 Cross-Counting Detection
The NVR software will count the times when objects (people, vehicle or other objects) cross
a pre-defined line, and the Cross-Counting event will be triggered. You can configure some
event actions like event recording, Email alert or pop-up full screen when an event is
triggered.
You can search and view the statistical result of cross counting on the Intelligent Analysis
page. Please refer to 3.1.7.11 Cross-Counting Analysis.
To configure the Cross-Counting settings:
1. Check the Switch checkbox to enable the function of the channel.
2. Select a Sensitivity value from the drop-down list. The larger the value, the higher the
sensitivity.
3. In the Scene field, select Indoor or Outdoor based on the location where your camera is
installed.
4. In the Setup field, click
to set up the detection line. Please refer to 3.1.7.6.1
Configuring Cross-Counting Detection Line for more details.
5. Click the Apply button to save the settings.
6. To further set up the alarm notifications, click the Alarm button to enter the Alarm setup
page. Please refer to 3.3.3 Intelligent Alarm.
54
AiO NVR Software
3.1.8.6.1 Configuring Cross-Counting Detection Line
Click the Setup button to enter the Line setup page.
1. Select 1 from the Rule Number drop-down list to configure the line.
2. Click the Rule Switch button to enable this rule.
3. Define a type for this rule.
AB: Detects movement from A to B.
BA: Detects movement from B to A.
4. To draw a line:
a. Use your mouse to click 2 points to draw a line.
b. If you want to move the line to other position or re-draw the line, select the line by
checking the red box on the upper-side of the line, the line will change to red color.
Drag and drop the line to a desired position. Drag the red dots of the line can re-size
the line.
1
c. Click the Save button to save the settings.
d. You can click the Remove All button to remove all the lines. To remove a certain line,
select the line by checking the red box on the upper-side of the line, and then click
the Remove button.
Note: The detection line should not be too short in order to enhance the detection
rate.
5. To return to the Line Crossing setup page, right-click the mouse.
55
AiO NVR Software
3.1.7.8 Sound Detection
To perform the Sound Detection function, the audio devices have to be pre-installed to the
IP cameras.
To configure the Sound Detection settings:
1. Check the Switch checkbox to enable the function of the channel.
2. In the Rise field, select Enable to enable the Sound Rise detection. And then further set
up the Rise Sensitivity and Sound Intensity.
3. In the Decline field, select Enable to enable the Sound Decline detection. And then
further set up the Decline Sensitivity.
4. If you want to enable recording when sound detection alarm is triggered, in the Record
Schedule field, click
to set up the recording schedule. Click and drag on the schedule
time blocks to draw the blocks with blue color, which will be applied with Sound Detection.
To deselect the blocks, click and drag on the blue blocks to select again. Click Save to save
the settings.
5. Click the Apply button to save the settings.
6. To further set up the alarm notifications, click the Alarm button to enter the Alarm setup
page. Please refer to 3.3.3 Intelligent Alarm.
56
AiO NVR Software
3.1.7.9 Tamper Detection
To configure the Tamper Detection settings:
1. Check the Switch checkbox to enable the function of the channel.
2. Select a Sensitivity value from the drop-down list. The larger the value, the higher the
sensitivity.
3. Click the Apply button to save the settings.
4. To further set up the alarm notifications, click the Alarm button to enter the Alarm setup
page. Please refer to 3.3.3 Intelligent Alarm.
5. If you want to activate the intelligent recording function, you need to configure the
recording schedule. Please refer to 3.1.7.10 Record Schedule.
57
AiO NVR Software
3.1.7.10 Record Schedule
In order to active the intelligent recording function, you need to configure the schedule
recording for Intelligent events. The schedule will be activated 24 hours a day, 7 days a week.
1. Select a channel and then move your mouse cursor over the schedule time blocks.
2. Click and drag on the schedule time blocks to draw the blocks with blue color, which will
be applied with intelligent event recording function. To deselect the blocks, click and
drag on the blue blocks to select again.
3. If you want to apply the same configurations from one channel to other channels, click
the Copy button. Select a channel from the Source Channel drop-down list and then
select the parameters you would like to apply to other channels. Select the desired
channels from the Target Channel field and then click the Copy button.
4. Click Apply to save the settings.
58
AiO NVR Software
3.1.7.11 Cross-Counting Analysis
On this page, you can search and view the statistical result of Cross-Counting Detection. For
more details on Cross-Counting Detection, please refer to 3.1.7.7 Cross-Counting.
Select the criteria and then click the Search button, the results will be listed at the lower
section.
59
AiO NVR Software
3.1.7.12 Driver Fatigue & Distraction
This function is only available for Vehicle model. You can enable or disable the Driver Fatigue
and Distraction Monitoring function on this page.
Driver Fatigue & Distraction
Channel: Displays the channel number.
Switch: Check the box to enable the function.
Buzzer: Select a time for eIVP model buzzer to sound when a fatigue event is triggered
(when the fatigue level reaches 30%). Select Disable to disable the function.
Alarm Out: Select an external alarm output device connected to the eIVP model (Local),
IPCam (CH) or both (All).
Alarm Output: Select an alarm output time (duration) when events occur. When an event is
triggered, the alarm will last based on the setup latch time.
Record: Click
and select the desired channel(s) you want to record when an event is
triggered on this channel. Note that for recording function to work, the Record Schedule
function has to be configured (please refer to 3.1.7.10 Record Schedule).
Post Recording: Select a post recording time when an event is triggered.
60
AiO NVR Software
After configuring the Driver Fatigue & Distraction monitoring function, go to the Live View
window, the system will start monitoring the driver. If the buzzer function has been enabled,
when the Fatigue and Distraction level reaches 30%, the buzzer will sound to warn the driver.
CH01
Processing time per frame: 54ms
Eyes closed: 236
Yawning: 58
Fatigue
Discontraction
Yaw: 2 (down)
Pitch: 3 (right)
Roll: 5
98 (%)
60 (%)
WARNING
Processing time per frame: Displays the processing time of the Fatigue function per frame.
Eyes closed: Displays the numbers of both eyes closed.
Yawning: Displays the numbers of yawning.
Fatigue Level: Displays the fatigue level. Yellow represents the fatigue level between 30%49%, orange for 50%-79%, red for above 80%. When the fatigue level reaches 50%, a
“WARNING” message will be displayed.
Distraction Level: Displays the Distraction level based on the head orientation angles (Roll,
Pitch, Yaw). Yellow represents the distraction level between 30%-49%, orange for 50%-79%,
red for above 80%. When the distraction level reaches 50%, a “WARNING” message will be
displayed.
Yaw: Displays the vertical angle.
Pitch: Displays the horizontal angle.
Roll: Displays the rotation angle.
61
AiO NVR Software
3.2 Record
You can configure the recording settings on this page.
3.2.1
Stream
On this page, you can configure the recording video or network transmission picture quality.
Generally, main stream defines the recording video quality which will be saved in the HDD;
sub stream defines the video quality which is being viewed via remote access, for example
web client and CMS; mobile stream defines the video quality which is being viewed via
remote access through mobile devices.
3.2.1.1 Main Stream
Main stream defines the recording video quality which will be saved in the HDD.
Channel: Displays channel number.
Stream Type: Displays the stream type.
Resolution: Select a recording resolution.
FPS: Select a FPS (frames per second) for the recording.
Video Encode Type: Select H.264 or H.265 based on your IP cameras.
Bitrate Control: Select CBR (constant bitrate) if the scene is simple and less changing, such
as a gray wall. Select VBR (variable bitrate) if the scene is complex, such as a department
store. If VBR is selected, select a video quality next to Bitrate Control.
Video Quality: If VBR is selected in the Bitrate Control field, select a video quality for VBR.
62
AiO NVR Software
Bitrate Mode: Select User-defined to set up bitrate manually; or Predefined to auto-select
bitrate.
Bitrate: The Bitrate corresponds to the speed of data transfer that the NVR software will use
to record video. Recordings that are encoded at higher bitrates, will be of better quality.
Audio: Select this option if you want to record audio along with video. Please ensure the
camera supports audio function.
i-Frame Interval: This function is only available for certain IP cameras. Please consult
EverFocus. Input an i-Frame interval.
I/O: Select this option if you want to enable external IO alarm for Main Stream recording.
Apply: Click to save the settings.
63
AiO NVR Software
3.2.1.2 Sub Stream
Sub stream defines the video quality which is being viewed via remote access, for example
web client and CMS.
Channel: Displays channel number.
Stream Type: Displays the stream type.
Resolution: Select a recording resolution.
FPS: Select a FPS (frames per second) for the recording.
Video Encode Type: Select H.264 or H.265 based on your IP cameras.
Bitrate Control: Select CBR (constant bitrate) if the scene is simple and less changing, such
as a gray wall. Select VBR (variable bitrate) if the scene is complex, such as a department
store. If VBR is selected, select a video quality next to Bitrate Control.
Video Quality: If VBR is selected in the Bitrate Control field, select a video quality for VBR.
Bitrate Mode: Select User-defined to set up bitrate manually; or Predefined to auto-select
bitrate.
Bitrate: The Bitrate corresponds to the speed of data transfer that the NVR software will use
to record video. Recordings that are encoded at higher bitrates, will be of better quality.
Audio: Select this option if you want to record audio along with video. Please ensure the
camera supports audio function.
i-Frame Interval: This function is only available for certain IP cameras. Please consult
EverFocus. Input an i-Frame interval.
Apply: Click to save the settings.
64
AiO NVR Software
3.2.1.3 Mobile Stream
Mobile stream defines the video quality which is being viewed via remote access through
mobile devices.
Channel: Displays channel number.
Switch: Check the box to enable the Mobile Stream function.
Stream Type: Displays the stream type.
Resolution: Select a recording resolution.
FPS: Select a FPS (frames per second) for the recording.
Video Encode Type: Select H.264 or H.265 based on your IP cameras.
Bitrate Control: Select CBR (constant bitrate) if the scene is simple and less changing, such
as a gray wall. Select VBR (variable bitrate) if the scene is complex, such as a department
store. If VBR is selected, select a video quality next to Bitrate Control.
Bitrate Mode: Select User-defined to set up bitrate manually; or Predefined to auto-select
bitrate.
Bitrate: The Bitrate corresponds to the speed of data transfer that the NVR software will use
to record video. Recordings that are encoded at higher bitrates, will be of better quality.
Audio: Select this option if you want to record audio along with video. Please ensure the
camera supports audio function and a microphone has been connected to the NVR software.
i-Frame Interval: Input an i-Frame interval.
Apply: Click to save the settings.
65
AiO NVR Software
3.2.2
Record
On this page, you can configure the recording parameters and recording schedule for each
channel.
3.2.2.1 Record
Channel: Displays channel number.
Enable Channel: Check the box to enable the function of the channel.
Record Stream: Select a recording stream for the channel. If you select Dual Streams, the
system will record both Main Stream and Sub Stream. If you select Main Stream, the system
will only record Main Stream.
Pre-Record: Check the box to enable the pre-record function. The NVR software will start
recording a few seconds before an alarm/event is triggered.
Copy: You can apply the same configurations from one channel to other channels. Select a
channel from the Source Channel drop-down list and then select the parameters you would
like to apply to other channels. Select the desired channels from the Target Channel field
and then click the Copy button.
Default: Click to apply the default setting.
Apply: Click to save the settings.
66
AiO NVR Software
3.2.2.2 Record Schedule
On this page, you can configure the recording schedule for Normal, Motion or I/O recordings.
Channel: Select a channel from the drop-down list.
Normal: Click the Normal button on the right-side and then move your mouse cursor over
the schedule time blocks. Click and drag on the schedule time blocks to draw the blocks with
green color, which will be applied with normal recording function.
Motion: Click the Motion button on the right-side and then move your mouse cursor over
the schedule time blocks. Click and drag on the schedule time blocks to draw the blocks with
yellow color, which will be applied with motion recording function. Note that for this
function to work, you will have to configure the motion settings in advance (please to 3.1.6
Motion).
IO: Click the IO button on the right-side and then move your mouse cursor over the schedule
time blocks. Click and drag on the schedule time blocks to draw the blocks with red color,
which will be applied with IO recording function. Note that for this function to work, you will
have to configure the IO settings in advance (please refer to 3.3.2 IO).
Copy: You can apply the same configurations from one channel to other channels. Select a
channel from the Source Channel drop-down list and then select the parameters you would
like to apply to other channels. Select the desired channels from the Target Channel field
and then click the Copy button.
Default: Click to apply the default setting.
Apply: Click to save the settings.
67
AiO NVR Software
3.2.3
Snapshot
On this page, you can configure the snapshot parameters or set up the snapshot schedule.
3.2.3.1 Snapshot
On this page, you can configure the snapshot parameters.
Channel: Displays the channel number.
Auto Snapshot: Check the box to enable the Auto Snapshot function. For this function to
work, you will have to configure the Snapshot Schedule (refer to 3.2.3.2 Snap. Schedule).
Stream Type: Select main stream or sub stream for the snapshot image.
Normal Interval: Configure an interval to automatically take a normal snapshot. For this
function to work, you will have to configure the Snapshot Schedule. Please refer to 3.2.3.2
Snap. Schedule.
Alarm Interval: Configure an interval to automatically take a snapshot when motion, IO
alarm is triggered. For this function to work, you will have to configure the Snapshot
Schedule. Please refer to 3.2.3.2 Snap. Schedule.
Copy: You can apply the same configurations from one channel to other channels. Select a
channel from the Source Channel drop-down list and then select the parameters you would
like to apply to other channels. Select the desired channels from the Target Channel field
and then click the Copy button.
Default: Click to apply the default setting.
Apply: Click to save the settings.
68
AiO NVR Software
3.2.3.2 Snap. Schedule
On this page, you can configure the snapshot schedule.
Channel: Select a channel from the drop-down list.
Normal: Click the Normal button on the right-side and then move your mouse cursor over
the schedule time blocks. Click and drag on the schedule time blocks to draw the blocks with
green color, which will be applied with normal snapshot function.
Motion: Click the Motion button on the right-side and then move your mouse cursor over
the schedule time blocks. Click and drag on the schedule time blocks to draw the blocks with
yellow color, which will be applied with motion snapshot function. Note that for this
function to work, you will have to configure the motion settings in advance (please refer to
3.1.6 Motion).
IO: Click the IO button on the right-side and then move your mouse cursor over the schedule
time blocks. Click and drag on the schedule time blocks to draw the blocks with red color,
which will be applied with IO snapshot function. Note that for this function to work, you will
have to configure the IO settings in advance (please refer to 3.3.2 IO).
Copy: You can apply the same configurations from one channel to other channels. Select a
channel from the Source Channel drop-down list and then select the parameters you would
like to apply to other channels. Select the desired channels from the Target Channel field
and then click the Copy button.
Default: Click to apply the default setting.
Apply: Click to save the settings.
69
AiO NVR Software
3.3 Alarm
You can configure the alarm settings on this page.
3.3.1
Motion
After configuring the Motion Detection settings, you can further configure the Motion Alarm
settings. To configure the Motion Detection setting, click the Motion button to enter the
Motion Detection setup page (please refer to 3.1.6 Motion).
GPS
G-Sensor
Channel: Displays the channel number.
Buzzer: Select a time for NVR software buzzer to sound when a motion event is triggered.
Select Disable to disable the function.
Alarm Out: Select an external alarm output device connected to the NVR software (Local),
IPCam (CH) or both (All).
Alarm Output: Select an alarm output time (duration) when events occur. When an event is
triggered, the alarm will last based on the setup time.
Record: Click
and select the desired channel(s) you want to record when a motion event is
triggered. Note that for recording function to work, the Record Schedule function has to be
configured (please refer to 3.2.2.2 Record Schedule).
Post Recording: Select a post recording time when a motion event is triggered.
70
AiO NVR Software
Show Message: Check the box to display the motion icon
motion event is triggered.
on the live channel when a
Send Email: Check the box to enable the Email alert function. When a motion event is
triggered, the NVR software will send an email alert with a snapshot to the pre-configured
Email receiver. Note that for this function to work, you have to set up the Email function in
advance (refer to 3.4.3 Email).
FTP Picture Upload: When an event is triggered, the NVR software will upload alarm images
to FTP server. Note that for this function to work, you have to set up FTP configurations in
advance. You can also configure the snapshot image resolution and quality, please refer to
3.4.4.1 FTP.
FTP Video Upload: When a motion event is triggered, the NVR software will upload alarm
videos to FTP server. Note that for this function to work, you have to set up FTP Schedule in
advance, please refer to 3.4.4.2 FTP Schedule.
Picture to Cloud: When a motion event is triggered, the NVR software will upload alarm
images to Cloud (Dropbox). Note that for this function to work, you have to set up Cloud in
advance, please refer to 3.5.2 Cloud.
Video to Cloud: When a motion event is triggered, the NVR software will upload alarm videos
to Cloud (Dropbox). Note that for this function to work, you have to set up Cloud in advance,
please refer to 3.5.2 Cloud.
Full Screen Trigger: If this function is enabled and a motion event is triggered, the triggered
channel will be displayed in full screen.
Motion: Click the Motion button to enter the Motion Detection setup page (please refer to
3.1.6 Motion).
Copy: You can apply the same configurations from one channel to other channels. Select a
channel from the Source Channel drop-down list and then select the parameters you would
like to apply to other channels. Select the desired channels from the Target Channel field and
then click the Copy button.
Default: Click to apply the default setting.
Apply: Click to save the settings.
71
AiO NVR Software
3.3.2
IO
After connecting the external IO devices to the NVR software or IPCam, you can further
configure the IO Alarm settings.
GPS
G-Sensor
Alarm In: Displays the alarm input number. Local: the IO devices connected to the NVR
software. CH: the IO devices connected to the IP cameras.
Alarm Type: Select an alarm type for the alarm input. Options include Normally-Open,
Normally-Close and Off.
Buzzer: Select a time for NVR software buzzer to sound when an IO event is triggered. Select
Disable to disable the function.
Alarm Out: Select an external alarm output device connected to the NVR software (Local),
IPCam (CH) or both (All).
Alarm Output: Select an alarm output time (duration) when events occur. When an event is
triggered, the alarm will last based on the setup time.
Channel: Click
and select the desired channel(s) you want to record when an IO event is
triggered. Note that for IO recording function to work, the Record Schedule function has to be
configured (please refer to 3.2.2.2 Record Schedule).
Post Recording: Select a post recording time when an IO event is triggered.
Show Message: Check the box to display the IO event icon on the live channel when an IO
event is triggered.
Send Email: Check the box to enable the Email alert function. When an IO event is triggered,
the NVR software will send an email alert with a snapshot to the pre-configured Email receiver.
72
AiO NVR Software
Note that for this function to work, you have to set up the Email function in advance (refer to
3.4.3 Email).
FTP Picture Upload: When an event is triggered, the NVR software will upload alarm images
to FTP server. Note that for this function to work, you have to set up FTP configurations in
advance. You can also configure the snapshot image resolution and quality, please refer to
3.4.4.1 FTP.
FTP Video Upload: When a motion event is triggered, the NVR software will upload alarm
videos to FTP server. Note that for this function to work, you have to set up FTP Schedule in
advance, please refer to 3.4.4.2 FTP Schedule.
Picture to Cloud: When an event is triggered, the NVR software will upload alarm images to
Cloud (Dropbox). Note that for this function to work, you have to set up Cloud in advance,
please refer to 3.5.2 Cloud.
Video to Cloud: When an event is triggered, the NVR software will upload alarm videos to
Cloud (Dropbox). Note that for this function to work, you have to set up Cloud in advance,
please refer to 3.5.2 Cloud.
Full Screen Trigger: If this function is enabled and an IO event is triggered, the triggered
channel will be displayed in full screen.
Copy: You can apply the same configurations from one channel to other channels. Select a
channel from the Source Channel drop-down list and then select the parameters you would
like to apply to other channels. Select the desired channels from the Target Channel field and
then click the Copy button.
Default: Click to apply the default setting.
Apply: Click to save the settings.
73
AiO NVR Software
3.3.3
Intelligent Alarm
After configuring the Intelligent function settings, you can further configure the Alarm settings
for each intelligent function. To configure the Intelligent functions, click the Intelligent button
to enter each intelligent function setup page (please refer to 3.1.7 Intelligent).
3.3.3.1 IVS Alarm Settings
The Intelligent Alarm setup configurations for the following intelligent functions are similar.
Perimeter Intrusion, Line Crossing, Foreign/Missing Object, Pedestrian Detection, Face
Detection, Loitering Detection, Cross-Counting Detection, Sound Detection and Tamper
Detection.
Here we use Perimeter Intrusion alarm setup page for example.
Channel: Displays the channel number.
Buzzer: Select a time for eIVP model buzzer to sound when an event is triggered. Select
Disable to disable the function.
Alarm Out: Select an external alarm output device connected to the eIVP model (Local),
IPCam (CH) or both (All).
Alarm Output: Select an alarm output time (duration) when events occur. When an event is
triggered, the alarm will last based on the setup latch time.
Record: Click
and select the desired channel(s) you want to record when an event is
triggered on this channel. Note that for recording function to work, the Record Schedule
function has to be configured (please refer to 3.1.7.10 Record Schedule).
74
AiO NVR Software
Post Recording: Select a post recording time when an event is triggered.
Show Message: Check the box to display an Intelligent event icon “S” or intelligent messages
on the live channel when an event is triggered.
Send Email: Check the box to enable the Email alert function. When an event is triggered, the
NVR software will send an email alert with a snapshot to the pre-configured Email receiver.
Note that for this function to work, you have to set up the Email function in advance (refer to
3.4.3 Email).
FTP Picture Upload: When an event is triggered, the NVR software will upload alarm images
to FTP server. Note that for this function to work, you have to set up FTP configurations in
advance. You can also configure the snapshot image resolution and quality, please refer to
3.4.4.1 FTP.
FTP Video Upload: When a motion event is triggered, the NVR software will upload alarm
videos to FTP server. Note that for this function to work, you have to set up FTP Schedule in
advance, please refer to 3.4.4.2 FTP Schedule.
Picture to Cloud: When an event is triggered, the NVR software will upload alarm images to
Cloud (Dropbox). Note that for this function to work, you have to set up Cloud in advance,
please refer to 3.5.2 Cloud.
Video to Cloud: When an event is triggered, the NVR software will upload alarm videos to
Cloud (Dropbox). Note that for this function to work, you have to set up Cloud in advance,
please refer to 3.5.2 Cloud.
Full Screen Trigger: If this function is enabled and an event is triggered, the triggered channel
will be displayed in full screen.
Intelligent: Click the button to enter each Intelligent setup page (please refer to 3.1.7
Intelligent).
Copy: You can apply the same configurations from one channel to other channels. Select a
channel from the Source Channel drop-down list and then select the parameters you would
like to apply to other channels. Select the desired channels from the Target Channel field and
then click the Copy button.
Default: Click to apply the default setting.
Apply: Click to save the settings.
75
AiO NVR Software
3.3.3.2 Face Recognition Alarm Settings
Facial recognition can help verify personal identity to accurately authenticate the users.
For this function to work, you will have to edit the database and group the users in advance.
1. Create a group. By default, Allow List, Block List and Stranger groups have been created. You
can click the Add button
to add more groups. Select a Policy and input a Similarity for the
added groups.
2. To add account users to the group:
a. Enable the Face Recognition function for the system to detect faces and take snapshot
images in database. Please refer to 3.1.7.5 Face Detection.
b. To add users to a group, click the Edit button
of a group. Click the Import button and
then click Local Storage Device to display the snapshot images from the local storage.
76
AiO NVR Software
c. Select a person you want to edit to the face recognition database and then click OK.
d. Input the info of the person and then click Import.
77
AiO NVR Software
e. To add more face images of this person in order to raise the face recognition accuracy,
click the Additional Face Image field and then click Local Storage Device to add more
images.
f. Click Modify to confirm setting.
78
AiO NVR Software
g. The user has been added to the system.
h. Follow Step 1 to add more users.
3. To set up the Alarm Output function, click the Alarm button of the group and then configure
the Alarm function.
Channel: Displays the channel number.
Buzzer: Select a time for eIVP model buzzer to sound when an event is triggered. Select
Disable to disable the function.
Alarm Out: Select an external alarm output device connected to the eIVP model (Local),
IPCam (CH) or both (All).
Alarm Output: Select an alarm output time (duration) when events occur. When an event is
triggered, the alarm will last based on the setup latch time.
Save Face: Check the checkbox to save face images when the system detects faces.
Save Background: Check the box to save background.
79
AiO NVR Software
Show Thumbnail: Check the box to display the face thumbnails on the Live Alarm Panel.
Send Email: Check the box to enable the Email alert function. When an event is triggered, the
NVR software will send an email alert with a snapshot to the pre-configured Email receiver.
Note that for this function to work, you have to set up the Email function in advance (refer to
3.4.3 Email).
FTP Picture Upload: When an event is triggered, the NVR software will upload alarm images
to FTP server. Note that for this function to work, you have to set up FTP configurations in
advance. You can also configure the snapshot image resolution and quality, please refer to
3.4.4.1 FTP.
Picture to Cloud: When an event is triggered, the NVR software will upload alarm images to
Cloud (Dropbox). Note that for this function to work, you have to set up Cloud in advance,
please refer to 3.5.2 Cloud.
4. To configure the Alarm Schedule of the Face Recognition function, click the Alarm Schedule
button to configure the alarm schedule.
5. Click the Apply button to save the settings.
6. The Face Recognition configuration is complete. Go to the Live View page and when there are
faces detected, the Face Recognition thumbnails will be displayed on the Live Alarm Panel.
80
AiO NVR Software
3.3.3.3 Statistics
You can search for the Facial Recognition statistics on this page.
81
AiO NVR Software
3.3.4
PTZ Linkage
You can associate an alarm trigger (motion or I/O) with a specific camera and then activate a
PTZ camera to go to a preset position when the alarm is triggered.
GPS
G-Sensor
Channel: Displays the channel number.
Switch: Check the box to enable the PTZ Linkage function.
Motion: Check the box to trigger the PTZ Linkage function when a motion event occurs.
IO: Check the box to trigger the PTZ Linkage function when an IO event occurs. Select an
external alarm output device connected to the eIVP model (Local), IPCam (CH) or both (All).
PTZ1-4: Associates the PTZ camera with preset points. Please set up the preset points of your
PTZ cameras in advance (please refer to 2.4.2.2 Preset Setting). After setting up the preset
points, click
to configure a PTZ camera and the preset number. If the PTZ camera is
assigned to CH2, select CH2 from the channel dropdown list and then select a desired preset
point. When an even is triggered, the configured PTZ camera will turn to the preset point.
Copy: You can apply the same configurations from one channel to other channels. Select a
channel from the Source Channel drop-down list and then select the parameters you would
like to apply to other channels. Select the desired channels from the Target Channel field and
then click the Copy button.
Default: Click to apply the default setting.
Apply: Click to save the settings.
82
AiO NVR Software
3.3.5
Exception
You can configure the system alarm settings on this page.
GPS
G-Sensor
Event Type: Displays the event types.
•
No Space on Disk: When an HDD is full.
•
Disk Error: When the HDD is not detected properly.
•
Video Loss: When a camera is not connected properly.
Switch: Check the box to enable the function.
Buzzer: Set up the time for buzzer to sound when an event is triggered. To disable the Buzzer
function, select Disable.
Alarm Out: Select an external alarm output device connected to the eIVP model (Local),
IPCam (CH) or both (All).
Alarm Output: Select an alarm output time (duration) when events occur. When an event is
triggered, the alarm will last based on the setup time.
Show Message: Check the box to display an alarm message on the upper-right corner of the
live channel when an event is triggered.
Send Email: Check the box to enable the Email alert function. When an event is triggered, the
NVR software will send an email alert with a snapshot to the pre-configured Email receiver.
Note that for this function to work, you have to set up the Email function in advance (refer to
3.4.3 Email).
Default: Click to apply the default setting.
Apply: Click to save the settings.
83
AiO NVR Software
3.3.6
Alarm Schedule
You can configure the schedule to activate the alarm functions including IO Alarm Output, FTP
Upload, Cloud Upload and Buzzer.
GPS
G-Sensor
84
AiO NVR Software
3.3.7
GPS
You can enable or disable the GPS function on this page. After setting up the configurations,
the GPS coordinates will be displayed on the Live View Window.
Note that for this function to work, users will have to pre-connect the GPS Antenna to the
antenna port on the eIVP model. For eIVP models without onboard GPS, please connect a GPS
module to the mini card slot on the motherboard inside your eIVP model.
GPS
Switch
Baud Rate
9600
Data Bit
8
Stop Bit
1
Parity
None
GPS
G-Sensor
Baud Rate: This field is to set the speed at which is used to transmit instruction or information
through the RS-485 port on the eIVP model. There are eight different speeds: 1200 BPS, 2400
BPS, 4800 BPS, 9600 BPS, 19200 BPS, 38400 BPS, 57600 BPS and 115200 BPS.
Data Bit: This field is the data bit at which you will be transferring. There are two settings for
this option: 8 or 7.
Stop Bit: This field is to set the stop bit for the RS232 connection. There are two different stop
bits, 1 or 2.
Parity: This field is to select the parity level at which you will be connected. You can choose
between None, Odd, or Even parity levels.
85
AiO NVR Software
3.3.8
G-Sensor
This function is only available for eIVP models with onboard G-Sensor. You can enable or
disable the G-Sensor function on this page. After enabling the function, the G-Sensor data will
be displayed on the Live View Window.
G-Sensor
Switch
GPS
G-Sensor
86
AiO NVR Software
3.4 Network
You can configure the network settings on this page.
3.4.1
General
This page allows you to configure network parameters, such as DHCP and PPPoE.
3.4.1.1 General
The DHCP setting lets the system use an automatically assigned (dynamic) IP address. This
address can change under certain circumstances, for instance, when the eIVP model’s
network switch/hub has to be rebooted. DHCP server in LAN will automatically assign an IP
configuration for the network connection.
WiFi
3G/4G
Xfleet
Port Configuration
DHCP: Check the box to enable the DHCP function. The router will automatically assign all
the below IP parameters to the eIVP model.
IP Address: The IP address of the eIVP model. The IP address consists of four groups of
numbers, separated by periods. For example, “192.168.001.100”.
Subnet Mask: Subnet mask is a network parameter which defines a range of IP addresses
that can be used on a network. The subnet address also consists of four groups of numbers,
separated by periods. For example, “255.255.000.000”.
Gateway: This address allows the eIVP model to access the Internet. The format of the
Gateway address is the same as the IP Address. For example, “192.168.001.001”.
DNS: DNS1 is the primary DNS server and DNS2 is a backup DNS server. Usually, it’s enough
to just enter the DNS1 server address.
Default: Click to apply the default setting.
Apply: Click to save the settings.
87
AiO NVR Software
3.4.1.2 PPPoE
This is a DSL-connection application. The ISP will ask the user to input a username and
password. Contact your ISP for these details.
Note: If PPPoE is selected as the IP type, the supplied IP Utility program will not be able to
detect the device.
WiFi
3G/4G
Xfleet
Check the Enable PPPoE box, and then enter the User name and Password provided by the
ISP. Click the Apply button, the system will reboot to activate the PPPoE setting.
88
AiO NVR Software
3.4.1.3 WiFi
You can set up the WiFi network on this page. Please note to enable WiFi, users need to
connect a WiFi module to the mini card slot on the motherboard inside the eIVP model, and
also connect WiFi antenna to the antenna port.
General
WiFi
3G/4G
Xfleet
Port Configuration
WiFi Mode
DHCP
IP
0.0.0.0
Subnet Mask
0.0.0.0
Gateway
0.0.0.0
DNS Server 1
0.0.0.0
DNS Server 2
0.0.0.0
Network Mode
Mixed
SSID
Shared Key
Change Channel
Auto
Security Mode
Open None
WPA Algorithms
AES
Wireless Mode: Select Disable to disable this function. Select Static IP to set up a fixed IP
for network connection. Select DHCP for DHCP server to automatically assign an IP
configuration for the network connection.
IP address: Displays the current IPv4 IP Address. A static IP address must be set manually. If
DHCP is selected, this value will be assigned automatically.
Subnet Mask: Displays the subnet mask for your network so the eIVP model will be
recognized within the network. If DHCP is selected, this value will be assigned automatically.
Gateway: Displays the gateway on your network for the eIVP model to use when
communicating with any devices not on the local network. If DHCP is selected, this value will
be assigned automatically.
DNS Server 1: Displays the primary DNS server for your network. If DHCP is selected and an
internet connection is available, this value should be assigned automatically. This field must
have a valid DNS address in order to use the DDNS feature (see 3.4.2 DDNS).
DNS Server 2: This field shows the secondary DNS server for your network.
Network Mode: Select a wireless networking standard.
SSID: Enter the name (SSID) of the wireless network.
Shared Key: Enter the password of the wireless network.
Change Channel: Select a wireless channel for the eIVP model. It’s recommended to select
Auto when there is more than one eIVP model set up on the same wireless network.
Security Mode: Select a wireless encryption protocol: WEP, WPA and WPA2.
WPA Algorithms: Select a WPA algorithm from the drop-down list.
Click Default to apply the default setting. Click Apply to save the settings.
89
AiO NVR Software
3.4.1.4 3G/4G
You can set up the 3G/4G network on this page.
GPRS Service
General
On
Done
APN
Dial Number
WiFi
3G/4G
Xfleet
Port Configuration
User Name
Password
IP
0.0.0.0
Subnet Mask
0.0.0.0
Gateway
0.0.0.0
DNS Server 1
0.0.0.0
DNS Server 2
0.0.0.0
ISP
NA
Type
NA
Signal
0
Status
Fail
Data Rate Upload
0 Mbps
Data Rate Download
0 Mbps
1. Connect a 3G or 4G module to the mini card slot on the motherboard inside your eIVP
model, connect the 3G/4G Antenna to the antenna port, and finally insert a SIM card to
the SIM card slot.
2. Select On from the GPRS Service drop-down list and select an authentication (CHAP or
PAP).
3. Insert the APN, Dial Number, User Name and Password provided by the network service
provider and then click the Apply button. The connection status will be displayed in the
Status field below.
Status: If the connection is established, the status will display “Success”.
Date Rate: If the connection is established, the Data Rate information, including upload
and download data rate, will be displayed.
ISP: Displays the information of internet service provider.
Type: Displays the network type, such as 3G or 4G.
Signal: Displays the signal strength (0~98). The higher the value, the stronger the signal
strength.
4. You can now use the IP for remote access to the eIVP model.
90
AiO NVR Software
3.4.1.5 Xfleet
You can use EverFocus Xfleet system for fleet management. Xfleet is a centralized
management platform which is well designed to not only monitor fleets, but also to track
driver statistics, maintenance records, fuel statistics and plenty of other in-depth analytics
reports that assist you to make decisions and eventually reduce overall costs.
With Xfleet, making prediction and optimizing business performance will no longer be a
burden as it provides timely response on the demands you need, creating long term value
for clients across industries.
General
WiFi
3G/4G
Xfleet
Server IP
0.0.0.0
Port
80
Account
Xfleet
Password
………
Status
(5~120 sec.)
Port Configuration
Meta Data Interval
5
Server IP: Input the IP address of the Xfleet.
Port: Input 6608 port and do not change the port as it is set up by default.
Account: Input the user name of the Xfleet.
Password: Input the password of the Xfleet.
Meta Data Interval: Input an interval for eIVP model to send meta data to the Xfleet system.
Click Default to apply the default setting. Click Apply to save the settings.
91
AiO NVR Software
3.4.1.6 Port Configuration
On this page, you can configure the port settings or enable/disable the UPnP or P2P function.
General
WiFi
3G/4G
Xfleet
Port Configuration
Web Port: The Web port can be used to remotely login the NVR software (e.g. using the
Web Client). If the default port 80 is already taken by other applications, please change it.
Client Port: The Client port can be used to send information through (e.g. using the mobile
app). If the default port 9000 is already taken by other applications, please change it.
RTSP Port: The RTSP port allows the NVR software to transmit real-time streaming to other
devices (e.g. using a streaming media player).
HTTPS: The Hypertext Transfer Protocol Secure (HTTPS) is a combination of the Hypertext
Transfer Protocol and the SSL/TLS protocol that provides encrypted communication and
secure identification of a network web server.
UPnP: Check the box to enable the UPnP function. If you want to remotely login the NVR
software using Web Client, you need to enable the UPnP function and also enable the Port
Forwarding function on your router.
Note:
1. For the UPnP function to work, an UPnP-enabled router is required.
2. If your router does not support UPnP, ensure the Port Forwarding function is manually
enabled on your router.
External IP: After enabling the UPnP function, the external IP address will be displayed.
P2P Switch: Check the box to enable the P2P function. If P2P function is enabled, a QR code
will be displayed on the System Info page. You can scan the QR code with EverFocus eFVMS
App installed on your mobile device to add and remote access the NVR software. Please
refer to 3.9.5.1.1 Performing the P2P Function.
TOE: Check the box to enable the TOE function.
Default: Click to apply the default setting.
Apply: Click to save the settings.
92
AiO NVR Software
3.4.2
DDNS
You can configure the DDNS setting on this page. DDNS (Dynamic Domain Name System) is a
service used to map a domain name to the dynamic IP address of a network device. You can
set up the DDNS service for remote access to the NVR software.
DDNS assigns a domain name (URL) to the eIVP model, so that the user does not need to go
through the trouble of checking if the IP address assigned by DHCP Server has changed. Once
the IP is changed, the eIVP model will automatically update the information to the DDNS to
ensure it is always available for remote access.
Note that before enabling the following DDNS function, user should have applied for a host
name from the DDNS service provider’s website. We highly recommend that you use
xxxx.everfocusddns.net for the simplicity of setting up your eIVP model. Please refer to
EverFocus DDNS on the next page.
DDNS: Check the box to enable the DDNS function.
Server: Select a DDNS service provider from the drop-down list. Note that before enabling the
following DDNS function, user should have applied for a host name from the DDS service
provider’s website.
Domain: Input the domain name obtained from the DDNS service provider.
User: Input the user name of the DDNS account.
Password: Input the password of the DDNS account.
Test DDNS: Click the button to test whether the DDNS function is working normally.
Default: Click to apply the default setting.
Apply: Click to save the settings.
93
AiO NVR Software
EverFocus DDNS
Please follow the steps below to set up EverFocus DDNS.
1. In order to allow remote access to the NVR software from outside of the local network,
enable either the Port Forwarding or DMZ function of your router. Please refer to the
manual of your router for more details.
2. Go to http://www.everfocusddns.net to check an available host name for the eIVP model.
Note that the host name of the eIVP model cannot include a space, underline or any
special characters particularly _~ ! @ # $ % ^ & * ( ) + < > " ; : . ,
3. Register the host name on the DDNS setup page for the eIVP model.
94
AiO NVR Software
a. Check DDNS to enable the DDNS function.
b. Select EVERFOCUS DDNS from the Server drop-down list.
c. Input the host name in the Device Name field.
d. Click the Apply button.
4. Configure the eIVP model Network settings, keep Web port “80” and enable the UPnP
function. Click the Apply button.
5. The DDNS setup is now complete. Open a browser and enter the domain name
(http://[host name].everfocusddns.net) in the address field. The Web interface of the
NVR software should be displayed.
For example, if you’ve obtained the host name “jjkktest” from EverFocus DDNS server,
enter http://jjkktest.everfocusddns.net in the address field of the browser.
http://jjkktest.everfocusddns.net
95
AiO NVR Software
3.4.3
Email
You can configure the email settings for email alerts, or configure the Email schedule on this
page.
3.4.3.1 Email Configuration
You can configure the email settings for email alerts. When events occur, the NVR software
will send Email alert with a snapshot image (.jpg) to the receiver(s).
Email: Check the box to enable the Email function.
Encryption: Select an encryption if your Email server requires the SSL or TLS verification.
Select Auto if you are not sure. Select Disable to disable this function.
SMTP Port: Enter the port number used by the SMTP server.
SMTP Server: Enter the SMTP server address of your Email.
User Name: Input your Email address.
Password: Input the password of the sender.
Sender: Input the Email address of the sender (the NVR software).
Receiver1-3: Input the Email address of the receiver. You can input 3 receiver email
addresses.
Interval: Configure an interval to send Emails when events occur.
Test Email: Click to test whether the Email function is working normally.
Default: Click to apply the default setting.
Apply: Click to save the settings.
96
AiO NVR Software
3.4.3.2 Email Schedule
You can configure the email schedule on this page. The selected event Email alerts will be
sent out by the scheduled time. For example, if you set up Motion on Sunday between 68am, the Motion Email alerts will only be sent out between 6-8am on Sunday.
Channel: Select a channel to configure the email schedule individually.
Motion: Click the Motion button on the right-side and then move your mouse cursor over
the schedule time blocks. Click and drag on the schedule time blocks to draw the blocks with
green color, which will be applied with motion email alert function. To enable Motion alarm,
please refer to 3.1.6 Motion.
IO: Click the IO button on the right-side and then move your mouse cursor over the schedule
time blocks. Click and drag on the schedule time blocks to draw the blocks with yellow color,
which will be applied with IO email alert function. To enable IO alarm, refer to 3.3.2 IO.
Exception (HDD full, HDD error or Video Loss): Click the Exception button on the right-side
and then move your mouse cursor over the schedule time blocks. Click and drag on the
schedule time blocks to draw the blocks with red color, which will be applied with exception
email alert function. To enable Exception alarm, please refer to 3.3.5 Exception.
Intelligent Analysis: Click the Intelligent Analysis button on the right-side and then move
your mouse cursor over the schedule time blocks. Click and drag on the schedule time blocks
to draw the blocks with blue color, which will be applied with Intelligent Analysis email alert
function. To enable Intelligent Analysis alarm, please refer to 3.3.3 Intelligent Alarm.
Copy: You can apply the same configurations from one channel to other channels. Select a
channel from the Source Channel drop-down list and then select the parameters you would
like to apply to other channels. Select the desired channels from the Target Channel field
and then click the Copy button.
Default: Click to apply the default setting.
Apply: Click to save the settings.
97
AiO NVR Software
3.4.4
FTP
3.4.4.1 FTP
You can configure the FTP server setting on this page. When there is a Motion or I/O event
occurs, the system will send an instant snapshot image to the FTP. For system alarm such as
HDD lost and Video loss, the system will send alarm log to the FTP as well.
FTP Enable: Check the box to enable the function.
Server IP: Input the FTP server IP.
Test FTP: Click to test the FTP server connection.
Port: Keep the port 21.
User Name: Input the user name of the FTP server.
Password: Input the password of the FTP server.
Picture Resolution: Select a resolution of the snapshot images for FTP uploading.
Picture Quality: Select a quality of the snapshot images for FTP uploading.
Video Stream Type: Select a stream type of the recordings for FTP uploading.
Max. Package Interval: Select a max. package interval for FTP uploading.
Directory Name: Input a directory of the FTP server.
Upload Normal Video: Select the desired channel(s) for uploading the normal recordings. For
this function to work, please setup the FTP Schedule (refer to 3.4.4.2 FTP Schedule) in advance.
Upload Alarm Video: To enable uploading alarm videos to the FTP Server, click the Motion,
PIR, IO or Intelligent buttons to enter each alarm setup page, and then check the FTP Video
Upload box to enable the function. For this function to work, please setup the FTP Schedule
(refer to 3.4.4.2 FTP Schedule) in advance.
Default: Click to apply the default setting.
Apply: Click to save the settings.
98
AiO NVR Software
3.4.4.2 FTP Schedule
You can configure the FTP schedule on this page. The selected event recordings will be
uploaded to the FTP by the scheduled time. For example, if you set up Motion on Sunday
between 6-8am, the Motion recordings will be uploaded to FTP between 6-8am on Sunday.
Note that for the FTP Schedule function to work, you have to enable FTP Video Upload
function on the related alarm setup page (Motion, PIR, IO, Intelligent).
Channel: Select a channel to configure the FTP schedule individually.
Normal: Click the Normal button on the right-side and then move your mouse cursor over
the schedule time blocks. Click and drag on the schedule time blocks to draw the blocks with
green color, which will be applied with normal recording FTP upload function. Note that for
this function to work, you have to select the desired channel(s) for uploading the normal
recordings (please refer to Upload Normal Video in 3.4.4.1 FTP.
Motion: Click the Motion button on the right-side and then move your mouse cursor over
the schedule time blocks. Click and drag on the schedule time blocks to draw the blocks with
yellow color, which will be applied with motion FTP upload function. To enable Motion alarm,
please refer to 3.1.6 Motion.
IO: Click the IO button on the right-side and then move your mouse cursor over the schedule
time blocks. Click and drag on the schedule time blocks to draw the blocks with red color,
which will be applied with IO FTP upload function. To enable IO alarm, refer to 3.3.2 IO.
Intelligent Analysis: Click the Intelligent Analysis button on the right-side and then move
your mouse cursor over the schedule time blocks. Click and drag on the schedule time blocks
to draw the blocks with blue color, which will be applied with Intelligent Analysis FTP upload
function. To enable Intelligent Analysis alarm, please refer to 3.3.3 Intelligent Alarm.
Copy: You can apply the same configurations from one channel to other channels. Select a
channel from the Source Channel drop-down list and then select the parameters you would
like to apply to other channels. Select the desired channels from the Target Channel field
and then click the Copy button.
Default: Click to apply the default setting.
Apply: Click to save the settings.
99
AiO NVR Software
3.4.5
IP Filter
You can configure the IP Filter settings on this page. This function allows you to allow or deny
some specific IP address to access the Web interface of the NVR software. By default, all IP
addresses are allowed.
To set up IP Filter:
1. Check the Enable box and then select either one from the two options below. You can only
activate one option for the NVR software.
Enable Whitelist: Enable the whitelist configured below.
Enable Blacklist: Enable the blacklist configured below.
2. Edit the Whitelist or Blacklist.
a. If you want to edit whitelist, select Whitelist from the Restricted Type drop-down box;
if you want to edit blacklist, select Blacklist from the Restricted Type drop-down box.
b. To add a single IP address to the list, input an IP address in the Start IP Address input
box and then click the Single Add button, the IP address will be added.
c. To add a range of IP addresses to the list, input the start IP address in the Start IP
Address input box and the end IP address in the End IP Address input box, and then
click the Network Segment Add button, the range of IP addresses will be added.
d. You can click the Edit icon
to edit the IP address, or click the Delete icon
delete the IP address from the list.
3. Click the Apply button to save the settings.
100
to
AiO NVR Software
3.5 Device
You can configure the internal HDD and Cloud storage function on this page.
3.5.1
Disk
3.5.1.1 Disk
You can configure the HDD settings on this page. Please connect the HDD(s) to the eIVP
model in advance and ensure the power and SATA cables are properly connected between
the eIVP model and HDD(s). After connecting the HDD(s) to the eIVP model, the NVR
software will automatically detect the connected HDD(s) and listed all the connected HDD(s)
in the below field.
For the first time connected HDDs, the status will show “Unformat” in the state column,
users will have to format the HDDs before you can use it.
The HDD(s) marked with * in the No. column indicates the HDD(s) is/are being used at
present.
Record on eSATA
Enable
Edit: Click the Edit button and the below window appears. You can assign each HDD to
different Disk Type (Read/Write, Read only or Redundancy) and Disk Group (Group 1 ~ 16).
A Redundant HDD can be used to automatically backup video footage on the recording
(read-write) hard drive. When a redundant HDD is set, the system can be set to record
cameras in parallel to both the recording hard drive and the redundant hard drive in case of
hard drive failure.
Checkbox: You can select the HDDs in the No column to select the HDD(s), and then you can
set up the Overwrite or eSATA function, or Format the HDD.
101
AiO NVR Software
Overwrite: Select Auto to enable the overwrite function; Off to disable the overwrite
function. If Auto is selected, the NVR software will overwrite the oldest files on the HDD
when HDD is full. If Off is selected, please check the HDD status regularly, to make sure the
HDD is not full.
The 1/3/7/14/30/90 Days stands for the last number of days to keep in the HDD. For
example, if 3 Days is selected, the last 3 days recordings will be kept in the HDD.
Format HDD: The first time use HDDs have to be formatted before you can use it. Select the
desired HDDs and then click the Format HDD button to format the selected HDDs. Note that
only the HDDs with “Unformat” status displayed in the State column are required to format
or the recording function will not work. WARNING: This will effectively ERASE the ENTIRE
hard disk!! Please backup the data from HDDs before formatting the HDDs.
Note:
1. Only the HDDs with “OK” in the State column can perform the recording function.
If not, format the HDDs before start using the recording function.
2. The “Free Time” on the HDD list indicates the remaining time for the HDD to
record based on the pre-setup resolution, streaming and fps.
Record on eSATA: If you have connected an external eSATA storage device to the NVR
software, you can enable the eSATA backup storage function.
Default: Click to apply the default setting.
Apply: Click to save the settings.
102
AiO NVR Software
3.5.1.2 Disk Group
You can assign the HDDs to different groups. HDD groups allow you to balance recordings
across multiple hard drives. For example, you can record channels 1~4 to one hard drive and
5~8 to a second hard drive. This can reduce the amount of wear on the hard drives and may
extend the life of the hard drives.
Disk Group Type: Select a Disk Group type. The Disk Group Type has to be pre-configured on
the Disk page (please refer to 3.5.1.1 Disk).
Disk Group: Select a Record Disk Group. The Record Disk Group has to be pre-configured on
the Disk page (please refer to 3.5.1.1 Disk).
Record Channel: Select the desired channel(s). The recordings of the selected channels will
be recorded to the selected Disk Group.
Default: Click to apply the default setting.
Apply: Click to save the settings.
103
AiO NVR Software
3.5.1.3 S.M.A.R.T
You can check the S.M.A.R.T. info of each HDD on this page.
To check the S.M.A.R.T. info of the HDD, select an HDD from the HDD ID drop-down list,
select a check type from the Self-Check Type drop-down list, and then click the Check button.
The S.M.A.R.T. info will be listed in the S.M.A.R.T. info field.
If the evaluation is not passed but you still want to use the disk for recording, you can check
the checkbox of Whole evaluation not passed. Continue to use the disk. And then click the
Save button to save the settings. Click Cancel to cancel and leave the page.
104
AiO NVR Software
3.5.2
Cloud
You can configure the Cloud settings (Dropbox cloud storage) on this page. After configuring
the settings, the system will automatically send the Motion and I/O alarm snapshot images or
recordings to the associated Dropbox when alarm events occur.
To perform the Cloud function:
1. Register an account on Dropbox website. It’s recommended to create the account with
the same Email address and password used for your NVR software.
2. Ensure the NVR software network is working properly.
3. Configure the SMTP function (refer to 3.4.3 Email).
4. Configure the Cloud settings and then click the Apply button.
a. Check the Cloud Storage checkbox to enable the Cloud function.
b. Select a Cloud Overwrite option.
c. Select a Video Type.
5. Click the Activate Cloud button to activate the Cloud function. The below message will
pup-up on the screen. Check your email and complete the cloud activation within 3
minutes.
105
AiO NVR Software
6. Go to your email box and click on the provided link, the below message appears. Input
the IP address of the NVR software and keep the 80 port. Click Authorize.
7. Input the user name and password of the NVR software and then click Log In.
8. The Cloud activation is complete.
106
AiO NVR Software
3.6 Layout
You can select the desired Layout or activate the Auto Sequence function on this page.
To select a layout, directly click on the layout icon.
To start displaying the sequence mode, click the Auto Sequence button. To stop the sequence
mode, click the button again. To configure the sequence settings, please refer to 3.9.1.3 Video
Output.
107
AiO NVR Software
3.7 Playback
3.7.1 General Operation
You can search and then play back the recordings on this page.
1
2
3
4
5
6
7
8
9
No. Name
Description
1
Search Mode
Click to enter each Search mode (General, Events, Time-period, Smart,
Tag, External File and Snapshot) to search and play back the
recordings. Please refer to 3.7.3 Search Mode for more details.
2
Playback Layout
The layout divisions will be automatically assigned by the system
based on the number of selected channels. For example, if 1 channel
is selected, the system will automatically assign single-division; if 2~4
channels are selected, 4-division will be assigned; if 5~9 channels are
selected, 9-division will be assigned; if 10~16 channels are selected,
16-division will be assigned.
3
Status Icon
Displays the playback status, such as speed, play, stop or step.
4
Close Button
You can click the Close button to close the Playback window and
return to the Live View window. You can also close the Playback
window by right-clicking the mouse.
5
Date
Click the Calendar button
6
Search Type
Select the desired search types for playback.
7
Stream Type
Select a stream type of the source recordings. For this function to
work, you will have to configure the record stream setting to Dual
Streams (please refer to 3.2.2.1 Record).
8
Channel Selection
Select the desired channel(s) to search and play back.
9
Playback Control
Panel
You can use the playback control panel for playback operation. Please
refer to 3.7.2 Playback Control Panel for more details.
108
to display the calendar and select a date.
AiO NVR Software
3.7.2 Playback Control Panel
You can use the playback control panel to operate the below functions:
1
2 3 4
5 6 7 8 9 10 11 12 13 14
15
16
17
18
19
20
Click to display the Playback Layout in full screen. Right-click the mouse
to exit the Full Screen. Please refer to 3.7.2.1 Full Screen on Playback
Window.
Click to rewind (x2, x4, x8, x16). The rewind speed will be displayed on
the Status Icon located on the upper-right corner of the Playback
Layout.
Click to start slow playback (1/2, 1/4, 1/8, 1/16). The slow play speed
will be displayed on the Status Icon located on the upper-right corner
of the Playback Layout.
1
Full Screen
2
Fast Backward
3
Slow Play
4
Play / Pause
Click to start or pause playing back.
5
Step Forward
Click to playback frame by frame.
6
Stop
Click to stop playing back.
Fast Forward
Click to Fast Forward (x2, x4, x8, x16). The fast forward speed will be
displayed on the Status Icon located on the upper-right corner of the
Playback Layout.
7
8
Zoom
9
Video Clip
10
Audio
11
Manual
Snapshot
Click to use the Digital Zoom function. To perform this function, select
a channel by clicking on the channel and then click the Zoom button,
the selected channel will be displayed in single-channel. And you can
start using the Digital Zoom function. For Digital Zoom operation,
please refer to 2.4.1 Digital Zoom (PIP) for more details.To exit Digital
Zoom mode, click the Zoom button again.
Click to quickly save a video clip (AVI) to a USB storage device. Please
refer to 3.7.2.2 Backup Video Clips.
Scroll the slider bar to increase or decrease volume.
Click to capture a snapshot image (.jpeg) of a channel and store it to
the USB storage device. To perform this function:
1. Insert a USB storage device to the NVR software.
2. Select a channel by clicking on the channel and then click the
Manual Capture button.
Note: For the first-time-use USB device, select a directory and then
click OK.
109
AiO NVR Software
12
Add Default
Tag
Click to add a default tag to the current playback time, which will be
applied with a default Tag Name “Tag”. You can then search for the tag
on the Tag window. Please refer to 3.7.3.5 Tag.
13
Add
Customized
Tag
Click to add a customized tag to the current playback time, which can
input a tag name to the tag. You can then search for the tag on the Tag
window. Please refer to 3.7.3.5 Tag.
14
Screenshot
Click to cut a screenshot and save it to the USB storage device. You can
also take a screenshot of a face and import the face image to the group
of Face Recognition.
15
Time Indicator
Indicates the current playback time.
16
Time Bar
You can use your mouse to drag the time bar to the left or right to
search the desired time for playing back. Single-click on the time bar at
a certain time will start playing back from the clicked time. The colors
on the time bar represent different recording types (refer to No.18).
Note that for the Motion, Intelligent and Alarm recording to work, you
have to configure the related settings in advance.
For Motion recording, please refer to 3.1.6 Motion.
For Intelligent recording, please refer to 3.1.7.10 Record Schedule.
For Alarm recording, please refer to 3.3.5 Exception.
17
Time Span
You can click to select a time span.
18
Selected
Channel
The selected channel will be applied with an Eye icon . You can
perform the Zoom, Audio or Manual Snapshot functions for the
selected channel.
19
The colors indicate the recording types.
Green: Normal recordings or manual recordings.
Time Bar Color Yellow: Motion recordings.
Indicator
Red: I/O recordings.
Blue: Intelligent recordings.
Orange: Alarm recordings.
20
Playback Date
Displays the selected playback date.
110
AiO NVR Software
3.7.2.1 Full Screen on Playback Window
On the Playback Control Panel, click the Full Screen button
to display the Playback
Layout in full screen. To exit the Full Screen, click the Full Screen button again on the
Playback Control Panel. You can also exit the Full Screen by right-clicking the mouse.
Under Full Screen mode, you can move your mouse to the right to display the right-side
Search Panel; or move your mouse to the bottom side to display the Playback Control Panel.
Search Panel
111
AiO NVR Software
Playback Control Panel
112
AiO NVR Software
3.7.2.2 Backup Video Clips
To backup video clips:
1. Ensure the USB storage device has been inserted to the NVR software.
2. On the Playback Control Panel, click the Video Clip button
. The button will then
change to a Copy button , and a copy range will be displayed on the time bar.
3. Check the left-side channel box if you want to back-up with the same start time and end
time of the selected channel(s).
4. To set up the start time and end time, drag the Triangle icons to the left or right.
5. Click the Copy button
, the below Copy Type window appears.
6. Click the Save button, the Copy window appears. You can also create a directory for the
video clip(s) by clicking the Directory button
on the upper-right corner.
7. Click the OK button, the backup process begins. After the backup process is complete,
click the Cancel button to return to the Playback window.
113
AiO NVR Software
3.7.3 Search Mode
3.7.3.1 General
You can use this page to search, play back and backup all types of recordings. Click the General
tab to enter the General Playback mode.
1.
Click the Calendar button to select a date.
2.
Select the desired Search Type(s).
3.
Select a Stream Type. For this function to work, you will have to configure the record
stream setting to Dual Streams (please refer to 3.2.2.1 Record).
4.
Select the desired channel(s).
5.
Click the Play button to start playing back.
6.
Use the Playback Control Panel to operate the Playback function. Please refer to 3.7.2
Playback Control Panel for more details.
Note: The layout divisions will be automatically assigned by the system based on the number
of selected channels. For example, if 1 channel is selected, the system will automatically
assign single-division; if 2~4 channels are selected, 4-division will be assigned; if 5~9 channels
are selected, 9-division will be assigned; if 10~16 channels are selected, 16-division will be
assigned.
114
AiO NVR Software
3.7.3.2 Events
You can use this page to search, play back and backup the event recordings to the USB storage
device. The Event Playback page gives you a summary of all events on the list. You can display
the events with Thumbnail, List or Details list type.
Event Search and Backup
1
3
2
4
Date
5
6
7
No. Name
Description
1
Event Tab
Click to enter the Event Playback page.
2
Event List
The searched events will be listed on the Event List. You can display
the Event List in Thumbnail, List or Details mode. Please refer to No.6.
Search Panel
You can use this panel to search for the event recordings based on the
selected attributes including date and time, record mode and
channels.
Close Button
You can click the Close button to close the Playback window and
return to the Live View window. You can also close the Playback
window by right-clicking the mouse.
3
4
115
AiO NVR Software
5
Function Bar
Descending order: Click to display the events in descending order.
Select: Check the box to select all the events on the list. Uncheck the
box to deselect all the events on the list.
Copy: Select the event(s) on the Event List and then click the Copy
button to backup the selected event recordings to the USB storage
device.
Play: Click an event on the Event List and then click the Play button to
play back the clicked event recording.
Selected: The number of selected event(s) on the Event List will be
displayed here.
Total Size: The total size of selected event(s) on the Event List will be
displayed here.
6
Browse Type
Click to display the Event List with Thumbnail, List or Details mode.
7
Event Info
Click an event on the Event List, the information of the clicked event
will be displayed here.
1.
To search for events:
a.
Click the Calendar button to select a date.
b. Click the Time column to select a time range.
c.
Select the desired Search Type(s).
d. Select a Stream Type. For this function to work, you will have to configure the record
stream setting to Dual Streams (please refer to 3.2.2.1 Record).
e.
Select the desired channel(s).
f.
Click the Search button
g.
You can click the left or right buttons to browse between pages, or input the page
number you want to browse.
, the search results will be displayed on the Event List.
h. You can switch the Event List display mode by clicking the Thumbnail, List or Details
icons.
Thumbnail: Click to display the events with thumbnail images.
List: Click to display the events in list.
116
AiO NVR Software
Details: Click to display the events in detailed list.
Playback: Click the Playback icon can play back the event.
Lock: Click the icon to lock
or unlock
the event. The locked events will be
stored in the hard disk and will not be overwritten.
i.
2.
On the Event List, click on an event and its information will be displayed at the lowerright corner.
To back up event recordings to the USB storage device:
a.
Ensure the USB storage device has been inserted to the NVR software.
b. On the Event List, select the desired event(s) and then click the Copy button.
3.
To play back an event recording, you can try either way:
•
On the Event List, double-click on an event, the Event Playback page appears
•
On the Event List, click on an event and then click the Play button on the Function bar,
the Event Playback page appears
•
On the Event List (Detail list), click the Playback button of an event, the Event Playback
page appears
117
AiO NVR Software
Event Playback page
Playback View
Event List
Playback Control Panel
Event Info
【Event List】 You can perform the below functions using the Event List.
Playback: There are two ways:
•
Double-click on an event can start playing back the event recording.
•
Click on an event and then click the Playback button
to start playing back.
Copy: Check the event boxes to select the events and then click the Copy button
back-up the event recordings to the USB storage device.
can
【Playback View】 You can perform the below functions using the Playback View.
Digital Zoom: Scroll the Playback View to zoom in or zoom out the images. You can also use
your mouse to drag the image to the desired positions to spot on a specific area.
Digital Zoom (PIP): Click the Zoom button on the Playback Control Panel and then scroll
mouse upward/downward to zoom in/out, a Navigation Box will be displayed on the
Preview Window. For more details about the operation, please refer to 2.4.1 Digital Zoom
(PIP).
Return to the Event Search Page: Right-click on the Playback View can return to the Event
Playback page. You can also click the Return button on the Playback Control Panel to
return to the Event Playback page.
【Event Info】 On the Event List, click on an event, the information of the clicked event will
be displayed here.
【Playback Control Panel】 You can use this panel to operate the playback function. Please
refer to 3.7.2 Playback Control Panel for more details.
118
AiO NVR Software
3.7.3.3 Time-Period
Click the Time-Period tab to enter this page. Time-Period function allows you to divide a
recording into several segments with equal time-length; and then play back the segments
simultaneously.
For example, for a 60-minute recording, if you select 4 split-screen, the recording will be
divided into 4 segments with 15-minute in length each. If you select 6 split-screen, the
recording will be divided into 6 segments with 10-minute in length each.
Date
Time
1.
Click the Sub-period tab on the top to enter the Sub-Period Playback page.
2.
Click the Calendar button to select a date.
3.
Click the Time column to select a time range.
4.
Select a split number from the Split-screens drop-down list.
5.
Select a Search Type.
6.
Select a Stream Type. For this function to work, you will have to configure the record
stream setting to Dual Streams (please refer to 3.2.2.1 Record).
7.
Select a channel for Sub-period playback by checking the checkbox of the channel.
8.
Click the Play button on the Playback Control Panel to start playing back. Please refer to
3.7.2 Playback Control Panel for more details about Playback Control Panel.
9.
You can also single-click on each segment on the playback layout to view the time range of
the clicked (selected) segment. Please refer to the image below.
119
AiO NVR Software
Date
Time
Segment
Whole Recording
120
AiO NVR Software
3.7.3.4 Smart
Smart Playback allows you to easily search and play back the motion events in one or more
specific areas of a channel.
Date
Time
To perform the Smart Playback function:
1. Click the Calendar button to select a date.
2. Click the Time column to select a time range.
3. Select the Search Type.
4. Select a channel for smart playback by checking the checkbox of the channel.
5. Click the Play button on the Playback Control Panel to start playing back.
6. By default, the whole area of the live image is defined as the smart area. To re-define the
smart area(s), click the Motion button
on the Playback Control Panel to enter the Smart
Area Define page. Please refer to Defining Smart Areas below.
7. Click the Search button on the Smart Area Define page to return to the Smart Playback page
and then click the Play button to start playing back. You can see the searched Smart Motion
Detection recordings displayed on the time bar in blue color (upper one).
Smart (Motion)
Whole Recording
8. You can operate the smart playback function using the Playback Control Panel. Please refer
to 3.7.2 Playback Control Panel for more details.
121
AiO NVR Software
Defining Smart Areas:
1. Follow Step 1 ~ Step 6 above to enter the Smart Area Define page.
Apply All
Click and hold it to drag it to other location
Clear All
Return
Search
2. To define the smart area(s), click the mouse and drag it to draw an area. The area applied
with the smart function will be shown with red grids. You can follow this method to draw
several areas. To clear a certain area, use the same method to draw on the same area again,
the smart area will be erased.
3. Click the Search button to start searching the motion events on the smart areas for playing
back.
122
AiO NVR Software
3.7.3.5 Tag
You can search for the tagged recordings and then play back the recordings.
After adding tags to the recordings, you can use the Tag playback window to search for the
tagged recordings.
There are two ways to add a tag:
1. On the Live View window, click the Add customized Tag icon on the Live Channel Toolbar.
Please refer to 2.4 Live Channel Toolbar for more details.
2. On the Playback windows (General, Events, Time-period, Smart), click the Add Default Tag
or the Add customized Tag icon on the Playback Control Panel. Please refer to 3.7.2
Playback Control Panel for more details.
To play back the tagged recordings:
123
AiO NVR Software
1. On the Tag playback window, select a Start Time and End Time.
2. Optionally input a keyword of the tag if you want to find the tags with customized names.
3. Select the desired channel(s).
4. Click the Search button
, the searched tags will be displayed on the list.
5. To play back the tagged recordings, you can either double-click on the tag recording or
select a tag recording and then click the Play button on the lower-left corner. The below
playback window appears.
a. By default, the NVR software will play back the tagged recordings for 1 minute starts
from 30 seconds ago of the tagged time. You can optionally adjust the playback time by
selecting the Pre-play or Post-play options and then click the Playback button.
b. You can edit the tag names by clicking the Edit icon, or delete the tags by clicking the
Delete icon.
c. You can now operate the tag playback function using the Playback Control Panel. Please
refer to 3.7.2 Playback Control Panel for more details.
d. To return to the Tag playback window, click the Close button or right-clicking the mouse.
124
AiO NVR Software
3.7.3.6 External File
You can play back the recordings (.avi) stored in the USB storage device using the External File
Playback window.
To play back the recordings (.avi) stored in the USB storage device:
1. Ensure the USB storage device has been inserted to the NVR software.
2. Select the USB device from the Device Name drop-down box.
3. Double-clicking the recordings on the right-side panel, the recording will be played back.
125
AiO NVR Software
3.7.3.7 Snapshot
You can use this page to search and play back the snapshot images and backup the images to a
USB storage device.
2
1
5
3
6
4
7
No. Name
Description
1
Snapshot
Click to enter the Snapshot Playback window.
2
The searched snapshot images will be listed on the Snapshot List. You
Snapshot List can display the Snapshot List in Thumbnail, List or Details mode. Please
refer to No.6.
3
4
Search Panel
You can use this panel to search for the snapshot images based on the
selected attributes including date and time, record mode, and
channels.
Close Button
You can click the Close button to close the Snapshot Playback window
and return to the Live View window. You can also close the Snapshot
Playback window by right-clicking the mouse.
126
AiO NVR Software
5
Function Bar
Descending order: Click to display the snapshots in descending order.
Select: Check the box to select all the snapshots on the list. Uncheck
the box to deselect all the snapshots on the list.
Copy: Select the snapshot(s) on the list and then click the Copy button
to backup the selected snapshot images to the USB storage device.
Play: Click a snapshot on the list and then click the Play button to play
back the snapshot images starting from the clicked one.
Selected: The number of selected snapshot(s) on the list will be
displayed here.
Total Size: The total size of selected snapshot(s) on the list will be
displayed here.
6
Browse Type
Click to display the snapshot list with Thumbnail, List or Details mode.
7
Event Info
Click an image on the Snapshot List, the information of the clicked
snapshot image will be displayed here.
1. To search for snapshot images:
a. Click the Calendar button to select a date.
b. Click the Time column to select a time range.
c. Select the desired Search Type(s) and channel(s).
d. Click the Search button
List.
, the search results will be displayed on the Snapshot
e. You can click the left or right buttons to browse between pages, or input the page
number you want to browse.
f. You can switch the Snapshot List display mode by clicking the Thumbnail, List or
Details button.
Thumbnail: Click to display the events with thumbnail images.
List: Click to display the snapshots in list.
127
AiO NVR Software
Details: Click to display the snapshots in detailed list.
Playback: Click the Playback icon in the Playback column can display the snapshot
image. You can then click the
buttons to display the next or previous
snapshot image.
g. On the Snapshot List, click on a snapshot image and its information will be displayed
at the lower-left corner.
2. To back up snapshot images to the USB storage device:
a. Ensure the USB storage device has been inserted to the NVR software.
b. On the Snapshot List, select the desired snapshot(s) and then click the Backup button.
3. To play back a snapshot images continuously:
a. On the Snapshot List, click on a snapshot and then click the Play button on the
Function bar, the Image Playback page appears.
b. The system will automatically play back the snapshot images starting from the clicked
one to the last one.
Snapshot Playback page
Snapshot List
Playback Control Panel
Event Info
【Snapshot List】 You can perform the below functions using the Event List.
128
AiO NVR Software
Image Display: Click a snapshot image on the list can display the image on the viewing
window.
Continuous Playback: Click a snapshot image on the list and then click the Play button on
the Playback Control Panel, the snapshot images will be automatically playing back
continuously starting from the clicked one to the last one.
Copy: On the Snapshot List, check the snapshot boxes to select the snapshots and then
click the Copy button
can back-up the snapshot images to the USB storage device.
【Event Info】 On the Snapshot List, click on a snapshot, the information of the clicked
snapshot image will be displayed here.
【Playback Control Panel】 You can use this panel to operate the playback function.
Return
Previous
Next
Play / Pause
Single
Quad
Nine-View
Return: Click to return to the Picture search page.
Previous: Click to display the previous image.
Play / Pause: Click to start playing back or pause playing back the continuous snapshot
playback.
Next: Click to display the next image.
Single: Click to display the snapshot images in single view.
Quad: Click to display the snapshot images in quad view (displaying 4 images at a time).
Nine-View: Click to display the snapshot images in nine-view (displaying 9 images at a time).
129
AiO NVR Software
3.7.3.8 Intelligent
You can use this page to playback the Face Recognition alarm recordings.
You can also add an E-map to display the location of the alarm channel.
130
AiO NVR Software
3.8 Express
3.8.1
Quick Playback
You can configure the start playback time for the Quick Playback function. Select a time from
the drop-down box to set up playing back from how many time ago.
After the configuration, you can activate the function by clicking the Quick Playback icon on
the Live Channel Tool Bar on each channel (please refer to 2.4 Live Channel Tool Bar).
f
3.8.2
Stream Switch
This function is only available for IP cameras. You can set up a stream mode for all IP channels
on the live view window. Select Main Stream or Sub Stream and then click the Apply button.
To adjust the Main Stream or Sub Stream configurations, please refer to 3.2.1 Stream.
3.8.3
Preview Policy
You can set up a displaying quality for all channels on the live view window. Select among
realtime, balanced or smooth view. The view modes affect only the live view video quality by
bit rate and frame rate but do not affect the recording quality.
131
AiO NVR Software
3.9 System
You can configure most of the system settings on the Main Menu.
3.9.1
General
3.9.1.1 General
You can configure the general system settings on this page.
Device Name: Input a desired name for your eIVP model. The name can include both letters
and numbers.
Language: Select a language.
Video Format: Select NTSC or PAL for the system.
Record Mode: Select a record mode, Normal (4k) or 5MP Mode. The recording FPS options
will be different when Normal Mode (4k) or 5MP Mode is selected. For more details about
recording FPS, please refer to 3.2.1 Stream.
Menu Timeout: Select a timeout time for the OSD menu to automatically exit. Select Off for
the OSD menu to display continuously.
Start Wizard: Check the box to enable starting the Startup Wizard every time when system
starts.
Default: Click to apply the default setting.
Apply: Click to save the settings.
132
AiO NVR Software
3.9.1.2 Date and Time
【Date and Time】
Date: Set up the date for the system.
Time: Set up the time for the system.
Date Format: Select a format for the date.
Time Format: Select a format for the time.
Time Zone: Select a time zone relevant to your region.
【NTP Settings】
The NTP (Network Time Protocol) function allows your eIVP model to automatically sync its
clock with a time server. This gives it the ability to constantly have an accurate time setting
(your eIVP model will periodically sync automatically).
Enable NTP: Check the box to enable the NTP function. When NTP function is enabled, the
system will calibrate the system time at 00:07:50 daily and every time when the system is
started up.
Server Address: Select a NTP server.
Update Now: Click to calibrate the system time.
133
AiO NVR Software
【DST Setting】
The DST (Daylight Saving Time) function allows you to select the amount of time that
Daylight Saving has increased by in your particular time zone or region.
Enable DST: Check the box to enable the DST function.
Time Offset: Select the amount of time that Daylight Saving has increased by in your time
zone. This refers to the difference in minutes, between Coordinated Universal Time (UTC)
and the local time.
Daylight Saving Time: Select Week or Date to configure the start/end time below.
Week: Select a month, a particular day and time when Daylight Saving starts and ends.
For example, 2am on the first Sunday of a particular month.
Date: Select the start date (click the calendar icon), end date and time when Daylight
Saving starts and ends.
Start Time: Select a start time for the DST to start.
End Time: Select an end time for the DST to stop.
Default: Click to apply the default setting.
Apply: Click to save the settings.
134
AiO NVR Software
3.9.1.3 Video Output
You can configure the monitor output settings on this page.
Video Output: Select Live Output (Main Monitor) and then configure the below settings.
Sequence Layout: Select a layout for the sequence mode. For example, if you select Layout4,
the NVR software will display a quad view layout for all channels in sequence order. To start
the sequence mode, go to OSD menu > Layout and then click the Auto Sequence button.
Click the button again to stop sequence mode.
Sequence Interval Time: Input a sequence interval time in second. By default, 5 seconds is
set up.
VGA/HDMI Resolution: Select a live resolution to be displayed on the output monitor. 1920
x 1080 will suit most TVs. If your NVR software supports 4K output resolution, you can select
either 2K (2560 x 1440) or 4K (3840 x 2160) to take advantage of the higher resolution that
your 4K TV provides.
Scale and Offset: The NVR software supports to adjust the size and position of the display
screen to match your monitor or TV. Click the Setup button to adjust.
Scale: To adjust the size of the displayed screen by scale.
X Offset: To move the displayed screen to the left or right.
Y Offset: To move the displayed screen to the top or bottom.
Click once or long press the left button of your mouse on the arrow to adjust the size and
position, or you can scroll the wheel of the mouse to adjust. Click the right button of your
mouse to exit, and click Apply to save your modifications.
Cursor Hidden Delay: Click the drop-down menu to select the time your NVR software will
hide the mouse cursor when idle. You can also disable this function by selecting Off
(password protection will be temporarily disabled).
Cursor Acceleration: To adjust the speed to move the mouse cursor.
Transparency: Slide the bar to the left or right to adjust the transparency for the OSD menu.
Default: Click to apply the default setting.
Apply: Click to save the settings.
135
AiO NVR Software
3.9.2
User Account
You can configure the user settings on this page. Up to 7 user accounts (1 administrator and 6
users) can be configured.
Default User: Select an user account as the default account.
User Edit: Click
to bring-up the User Edit window. You can edit the user name/password in
this window. Input the user name with alphabetic or numeric characters; and the passwords
have to be numeric (0-9) and at least 5 characters. Select Enable from the User Enable dropdown list to enable the user account. Select Enable from the Password Enable drop-down list
to enable the password (if Disable is selected, the user can login without password). Click Save
to save the settings.
Admin Account
User Account
• Enable Unlock Pattern: Enable or disable the Unlock Pattern function.
Permission: Click
to display the User Permission window. The Administrator account has
full privileges so the functions cannot be configured. In the User Permission window, check
the boxes to grant functions for the selected user account. You can also set up the
Copy/Live/Playback/PTZ functions to specific channels. After the configuration, click Save to
save the settings.
136
AiO NVR Software

Log Search: Allow users to check all the system logs.

Settings: Allow users to set all the parameter settings.

Auto Reboot: Allow users to auto reboot the device.

Manual Record: Allows users to manually start/stop recording.

Disk: Allow users to manage and control the HDD and USB storage device.

Remote Login: Allow users to login the system remotely.

Sequence Control: Allow users to use the sequence function.

Manual Snapshot: Allow users to use the manual snapshot function.

Copy: Check the Copy box to enable the function; and then select the desired
channels to backup. This user account will be granted with the Backup function for the
selected channels.

Live: Check the Live box to enable the function; and then select the desired channels
for live view display. This user account will be granted with the live view display
function for the selected channels.

Playback: Check the Playback box to enable the function; and then select the desired
channels for playback. This user account will be granted with the playback function for
the selected channels.

PTZ: Check the PTZ box to enable the function; and then select the desired channels
for PTZ function. This user account will be granted with the PTZ control function for
the selected channels.
137
AiO NVR Software
3.9.3
Maintenance
On this page, you can search and view the system log, load default settings, upgrade the
system, export and import system parameters and manager system auto reboot.
3.9.3.1 Log
You can search for logs on this page. Select the start time, end time, log type and then click
the Search button, the searched logs will be displayed on the list below. Double-click on a
log from the list can bring up the Log Details window.
You can click the Playback icon
in the Playback column to play back the event recording.
About the playback control bar, please refer to 3.7.2 Playback Control Panel. To exit the
playback mode, right click the mouse.
Copy: Click to save all the searched logs to the USB storage device.
138
AiO NVR Software
Click the Copy button, the Copy window appears. You can also create a directory for the
video clip(s) by clicking the Directory button
on the upper-right corner. Click the OK
button, the copy process begins. After the copy process is complete, click the Cancel button
to return to the Log page.
Copy
139
AiO NVR Software
3.9.3.2 Load Default
Select the desired items to be restored to factory default and then click Apply. Restoring
default settings will not delete recordings and snapshots saved to the hard drive.
3.9.3.3 Upgrade
You can upgrade system firmware using this page.
1. Restore the firmware file (.sw) in a USB storage device and insert the USB storage device
to the eIVP model.
2. Click the Select File button to select the firmware file from the USB storage device.
3. Click the Upgrade button to start system upgrade.
Note: Do not take out the USB storage device or turn off the power during system
upgrading. When the upgrade is done, the system will restart automatically.
140
AiO NVR Software
3.9.3.4 System Parameter
You can export the system parameters you have configured to a USB storage device, or
import a system parameters file from USB storage device to the eIVP model.
Save Settings: Click to save the NVR software current system settings to the USB device. You
will be required to input the Admin password to authenticate.
Load Settings: Once you have exported system parameters file, you can import the file on
another eIVP model. Stored the file to your USB storage device and then insert the USB
storage device to the eIVP model, click Load Settings to navigate the file. You will be
required to input the Admin password to authenticate.
3.9.3.5 Auto Reboot
This menu allows the system to auto reboot the eIVP model regularly. It is recommended to
leave this function enabled, as it maintains the operational integrity of your eIVP model.
Check the Auto Reboot box to enable the function and then set up the reboot time for the
system to regularly reboot at the setup time. Click the Apply button to save the settings.
141
AiO NVR Software
3.9.4
IPCam Maintain
This menu allows you to upgrade the IP camera’s firmware and restore default settings of IP
camera.
3.9.4.1 Upgrade
This menu allows you to upgrade the IP camera’s firmware.
1. Select one of the IP cameras you want to upgrade firmware by checking the checkbox.
2. Click the Select File button to select the update file from your USB storage device.
3. Click the IPCam Upgrade button to start upgrading the selected IP camera. You will be
required to input the Admin password to authenticate.
3.9.4.2 Load Default
1. Select one of the IP cameras you want to load factory default by checking the checkbox.
2. Click the Load Default button to start loading default. You will be required to input the
Admin password to authenticate.
142
AiO NVR Software
3.9.4.3 Reboot IPC
On this page, you can reboot the IP cameras.
1. Select one of the IP cameras you want to reboot by checking the checkbox.
2. Click the Reboot IPC button to start rebooting. You will be required to input the Admin
password to authenticate.
3.9.4.4 System Parameter
You can export the IP camera parameters to a USB storage device, or import a IP camera
parameters file from USB storage device to the eIVP model.
Save Settings: Click to save the IP camera settings to the USB device. You will be required to
input the Admin password to authenticate.
Load Settings: Once you have exported IP camera parameters file, you can import the file on
another eIVP model. Stored the file to your USB storage device and then insert the USB
storage device to the eIVP model, click Load Settings to navigate the file. You will be
required to input the Admin password to authenticate.
143
AiO NVR Software
3.9.5
System Info
This menu allows you to view the system information, channel information, record
information and network status.
3.9.5.1 System Info
View system information such as device ID, device model name, IP address, MAC address,
firmware version and more.
If P2P function is enabled, a QR code will be displayed on the Info page. You can scan the QR
code with EverFocus eFVMS App installed on your mobile device to add and remote access
the NVR software. To enable the P2P function, please refer to 3.4.1.3 Port Configuration.
3.9.5.1.1 Performing the P2P Function
The P2P function allows users to add eIVP model to EverFocus’ eFVMS App through QR code.
1. Install EverFocus eFVMS App. For Android users, go to Google Play Store. For iOS users,
go to Apple Store. After the installation process is complete, start the eFVMS App.
eFVMS by EverFocus
EverFocus eFVMS
144
AiO NVR Software
2. To add a eIVP model through P2P, tap Menu > Device List, and then tap the “+” button
on the upper-right corner.
3. Scan the eIVP model’s QR code on the System Info page of the NVR software OSD menu.
Input the eIVP model ID, password and Media Port 9000. Tap the Save button.
……
145
AiO NVR Software
4. The eIVP model is now added and connected to the App. You can start accessing the NVR
software.
3.9.5.2 Channel Info
You can see the channel info on this page.
146
AiO NVR Software
3.9.5.3 Record Info
You can see the record info on this page.
3.9.5.4 Network Info
You can see the network state on this page.
Total Bandwidth: It shows the NVR software’s total input bandwidth for IP cameras.
Used Bandwidth: It shows the used bandwidth of IP cameras.
147
AiO NVR Software
3.10 Exit
You can Shutdown, Reboot or Logout the system using this page.
148
EverFocus Electronics Corp.
EverFocus Taiwan:
2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng
Dist., New Taipei City 222, Taiwan
TEL: +886 2 2662 2338
FAX: +886 2 2662 3632
www.everfocus.com.tw
marketing@everfocus.com.tw
EverFocus China - Shenzhen:
3F, Building 7, Longcheng Industrial Park, No.39,
Longguan No.7 Road, Dalang Street, Longhua,
Shenzhen, Guangdong, China
TEL: +86 755 2765 1313
FAX: +86 755 2765 0337
www.everfocus.com.cn
marketing@everfocus.com.cn
EverFocus USA - California:
1801 Highland Avenue, Unit A, Duarte, CA 91010, USA
TEL: +1 626 844 8888
FAX: +1 626 844 8838
www.everfocus.com
sales@everfocus.com
EverFocus Japan:
3F, Kuramochi, Building II, 2-2-3 Koto-Bashi,SumidaKu, Tokyo, 130-0022, Japan
TEL: +81 3 5625 8188
FAX: +81 3 5625 8189
www.everfocus.co.jp
info@everfocus.co.jp
Your EverFocus product is designed and
manufactured with high quality materials
and components which can be recycled
and reused.
This symbol means that electrical and
electronic equipment, at their end-of-life,
should be disposed of separately from
your household waste.
Please, dispose of this equipment at your
local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Ihr EverFocus Produkt wurde entwickelt
und hergestellt mit qualitativ
hochwertigen Materialien und
Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass elektrische
und elektronische Geräte am Ende ihrer
Nutzungsdauer vom Hausmüll getrennt
entsorgt werden sollen.
Bitte entsorgen Sie dieses Gerät bei Ihrer
örtlichen kommunalen Sammelstelle oder
im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising