EverFocus | eIVP1300 | Owner Manual | Everfocus eIVP1300 Owner Manual

Everfocus eIVP1300 Owner Manual
eIVP1300
Intel Atom E3845 / E3825 Mobile Network Video Recorder with 4Channel IP Cameras
User’s Manual
Copyright © EverFocus Electronics Corp.
Release Date: August 2019
EVERFOCUS ELECTRONICS CORPORATION
eIVP1300
Intel Atom E3845 / E3825 Mobile Network Video
Recorder with 4-Channel IP Cameras
User’s Manual
 1995-2019 EverFocus Electronics Corp.
www.everfocus.com.tw
Disclaimer
All the images including product pictures or screen shots in this document are for example only. The
images may vary depending on the product and software version. Information contained in this document
is subject to change without notice.
Copyright
All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form
or by any means without written permission of the EverFocus Electronics Corporation.
Microsoft Windows is a registered trademark of Microsoft Corp.
Intel, Pentium, Celeron, and Xeon are registered trademarks of Intel Corporation
Core, Atom are trademarks of Intel Corporation
ITE is a trademark of Integrated Technology Express, Inc.
IBM, PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation.
All other product names or trademarks are properties of their respective owners.
Safety Precautions
Please read the following safety instructions carefully. It is advised that you keep this manual
for future references.
 All cautions and warnings on the device should be noted.
 All cables and adapters supplied by EverFocus are certified and in accordance with the
material safety laws and regulations of the country of sale. Do not use any cables or
adapters not supplied by EverFocus to prevent system malfunction or fires.
 Make sure the power source matches the power rating of the device.
 Position the power cord so that people cannot step on it. Do not place anything over the
power cord.
 Always completely disconnect the power before working on the system’s hardware.
 No connections should be made when the system is powered as a sudden rush of power
may damage sensitive electronic components.
 If the device is not to be used for a long time, disconnect it from the power supply to avoid
damage by transient over-voltage.
 Always disconnect this device from any AC supply before cleaning.
 While cleaning, use a damp cloth instead of liquid or spray detergents.
 Make sure the device is installed near a power outlet and is easily accessible.
 Keep this device away from humidity.
 Place the device on a solid surface during installation to prevent falls.
 Do not cover the openings on the device to ensure optimal heat dissipation.
 Watch out for high temperatures when the system is running.
 Do not touch the heat sink or heat spreader when the system is running.
 Never pour any liquid into the openings. This could cause fire or electric shock.
 As most electronic components are sensitive to static electrical charge, be sure to ground
yourself to prevent static charge when installing the internal components. Use a grounding
wrist strap and contain all electronic components in any static-shielded containers.
 If any of the following situations arises, please contact our service personnel
(ts@everfocus.com.tw):
-
Damaged power cord or plug
Liquid intrusion to the device
Exposure to moisture
Device is not working as expected or in a manner as described in this manual
The device is dropped or damaged
Any obvious signs of damage displayed on the device
 DO NOT LEAVE THIS DEVICE IN AN UNCONTROLLED ENVIRONMENT WITH TEMPERATURES
BEYOND THE DEVICE’S PERMITTED STORAGE TEMPERATURES (SEE SPECIFICATION) TO
PREVENT DAMAGE.
ii
FCC Statement
This device complies with Part 15 FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received including
interference that may cause undesired operation.
Caution:
There is a danger of explosion if the battery is incorrectly replaced. Replace only with the same
or equivalent type recommended by the manufacturer. Dispose of used batteries according to
the manufacturer’s instructions and your local government’s recycling or disposal directives.
Attention:
Il y a un risque d’explosion si la batterie est remplacée de façon incorrecte.
Ne la remplacer qu’avec le même modèle ou équivalent recommandé par le constructeur.
Recycler les batteries usées en accord avec les instructions du fabricant et les directives
gouvernementales de recyclage.
iii
RoHS Requirements
設備名稱 (Equipment): 網路數位錄放影機,型號(型式)/ Type designation (Type): eIVP1300
單元Unit
限用物質及其化學符號 Restricted substances and its chemical symbols
鉛Lead
汞Mercury
鎘Cadmium
(Pb)
(Hg)
(Cd)
六價鉻
Hexavalent
chromium
多溴聯苯
Polybrominated
biphenyls
(Cr+6)
(PBB)
多溴二苯醚
Polybrominated
diphenyl ethers
(PBDE)
印刷電路板及
電子零組件
X
○
○
○
○
○
X
○
○
○
○
○
PCB & Other
Components
外部訊號連接
器及線材
Wires &
Connectors for
External
Connections
O:表示該有毒物質在該部件所有均質材料中的含量均在SJ/T 11363-2006標準規定的限量要求以下。
The quantity of poisonous or hazardous substances or elements found in each of the component's parts is
below the SJ/T 11363-2006-stipulated requirement.
X:表示該有毒物質至少在該部件的某一均質材料中的含量超出 SJ/T 11363-2006標準規定的限量要求。
The quantity of poisonous or hazardous substances or elements found in at least one of the component's
parts is beyond the SJ/T 11363-2006-stipulated requirement.
備註: 一、此產品所標示之環保使用期限,係指在一般正常使用狀況下。The Environment Friendly Use
Period as labeled on this product is applicable under normal usage only
iv
TABLE OF CONTENTS
1.
Introduction ............................................................................................................................ 1
1.1
Features .......................................................................................................................... 1
1.2
Dimensions...................................................................................................................... 2
1.3
Packing List ...................................................................................................................... 2
1.4
Front Panel ...................................................................................................................... 3
1.5
Rear Panel ....................................................................................................................... 4
2. Connection and Installation .................................................................................................... 5
2.1
Storage Installation ......................................................................................................... 5
2.1.1 Storage Compatibility List ........................................................................................... 6
2.2
DC Out Cable ................................................................................................................... 7
3. AMI BIOS Setup ....................................................................................................................... 8
3.1
System Test and Initialization ......................................................................................... 8
3.2
AMI BIOS Setup ............................................................................................................... 9
3.3
Setup Submenu: Main .................................................................................................... 9
3.4
Setup Submenu: Advanced ........................................................................................... 10
3.4.1 Advanced: Power Management ............................................................................... 10
3.4.1.1 Power Management: S5 RTC Wake Settings ........................................................ 12
3.4.2 Advanced: Super IO Configuration ........................................................................... 13
3.4.2.1 Super IO Configuration: Serial Port 1 Configuration ............................................ 13
3.4.2.2 Super IO Configuration: Serial Port 2 Configuration ............................................ 14
3.4.2.3 Super IO Configuration: Serial Port 3 Configuration ............................................ 14
3.4.2.4 Super IO Configuration: Serial Port 4 Configuration ............................................ 15
3.4.2.5 Super IO Configuration: Smart Fan Function ........................................................ 17
3.4.2.6 Super IO Configuration: Smart Fan Mode Configuration ..................................... 17
3.4.3 Advanced: Digital IO.................................................................................................. 18
3.4.4 Advanced: H/W Monitor........................................................................................... 19
3.4.5 Advanced: CPU Configuration................................................................................... 19
3.4.5.1 CPU Configuration: Socket 0 CPU Information ..................................................... 20
3.4.6 Advanced: IDE Configuration .................................................................................... 20
3.4.7 Advanced: CSM Configuration .................................................................................. 21
3.4.8 Advanced: Trusted Computing ................................................................................. 22
3.4.9 Advanced: USB Configuration ................................................................................... 23
3.4.10 Advanced: Touch Device ....................................................................................... 24
3.5
Setup Submenu: Chipset ............................................................................................... 24
3.5.1 Chipset: Host Bridge.................................................................................................. 25
3.5.1.1 CPU Configuration: Socket 0 CPU Information ..................................................... 26
3.5.2 Chipset: South Bridge................................................................................................ 27
3.5.2.1 South Bridge: Azalia HD Audio .............................................................................. 28
3.5.2.2 South Bridge: USB Configuration .......................................................................... 29
3.5.2.3 South Bridge: PCI Express Configuration .............................................................. 30
3.6
Setup Submenu: Security .............................................................................................. 31
3.7
Setup Submenu: Boot ................................................................................................... 32
3.8
Setup submenu: Exit ..................................................................................................... 33
4. Specification .......................................................................................................................... 34
v
eIVP1300 AI Mobile NVR
Chapter
1
1. Introduction
The eIVP1300 is one of EverFocus’ eIVP series AI mobile NVRs adopting Intel® Atom™ processor
and Movidius™ Myriad™ X AI core module. The model supports 4 IP cameras, wide operating
temperature ranging from 0°C to 60°C, and wide DC range of DC 9-24V. The eIVP1300 is complied
with the MIL-STD-810G standard for the utmost viability for vehicular use. Besides, the model is
also CE, FCC and RoHS certified. The eIVP1300 AI mobile NVR carries everything you need for
computing on the road.
1.1 Features
•
•
•
•
•
•
•
•
•
•
•
•
•
In-vehicle network video recorder platform
Intel® Atom™ E3845 / E3825 processor
Onboard DDR3L memory up to 4GB
Intel® Integrated Graphics Engine supports 2 display outputs by HDMI x 1, VGA x 1
Intel® I211 (or 210) Ethernet x 2 ports (GbE x 2)
Supports 4-channel IP cameras
Supports removable SSD storage (optional)
Supports 8-bit digital I/O (optional), USB2.0 x 3, USB3.0 x 1
Supports RS-232 x 2
Intel® Movidius™ Myriad™ X AI core module (optional)
Supports CAN Bus 2.0B (optional)
Wide DC range DC 9-24V
CE, FCC, RoHS certified
1
eIVP1300 AI Mobile NVR
1.2 Dimensions
186.5
177.8
50.4
180.3
211.8
Unit: mm
1.3 Packing List
• NVR x 1
• DC Power Terminal Block d x 1
• DC Out Cable x 1 (power supply for
cameras)
•
•
•
•
mSATA Screw x 1
2.5” SSD Screw x 4
User Manual x 1
CD x 1 (see Note 3)
Note:
1. Equipment configurations and supplied accessories vary by country. Please consult your
local EverFocus office or agents for more information. Please also keep the shipping carton
for possible future use.
2. Contact the shipper if any items appear to have been damaged in the shipping process.
3. The CD contains the User Manual and some Drivers for the system. If you can’t find the
required drivers from the CD, please go to our website for related drivers.
www.everfocus.com.tw
2
eIVP1300 AI Mobile NVR
1.4 Front Panel
1
2
3
4
No.
Name
Description
1
USB2.0 Ports
USB2.0 ports.
2
Reset
Press the button to restart the system.
3
Power Button
Press the button to turn on or turn off the system.
4
LED Indicator
Power: When power is on, the LED will continue lighting in red.
HDD: When storage is reading/writing data, the LED will flashes green.
3
eIVP1300 AI Mobile NVR
1.5 Rear Panel
1
6
7
2
3
4
5
8
9
10
11
1
No. Name
Description
1
Antenna
Connects the antenna to the mobile NVR for 3G / 4G / WiFi functions.
2
VGA Port
VGA display output.
3
HDMI Port
HDMI display output.
4
WAN/LAN
Connects to the Network.
5
USB2.0 Port
USB3.0 Port
USB ports.
6
Audio Input
Connects to audio input devices, such as microphones. Note that the
microphones with a (built-in) amplifier and external power supply are
required.
7
Audio Output
Connects to an audio output device, such as speakers. Note that the
speakers with a (built-in) amplifier and external power supply are
required.
8
COM2
RS-232 port.
9
COM1
RS-232 port.
10
Power Output
A total of 12VDC, 2A power supply to the connected cameras. Please refer
to 2.2 DC Power Out Cable.
11
Power Input
Insert the supplied DC Power Terminal Block and then connect the
system to a DC 9-24V power source.
4
eIVP1300 AI Mobile NVR
Chapter
2
2. Connection and Installation
2.1 Storage Installation
The eIVP1300 supports mSATA drive (half size) and 2.5” SSD for storage. You can install either
one for storage.
To install the mSATA (half size) drive:
1.
Make sure the NVR is power-off.
2.
Unscrew the four screws on the rear panel and then remove the cover from the housing.
3.
Find the mSATA Interface on the motherboard and then screw your mSATA (half size) drive
to the mSATA Interface using the supplied mSATA Screw.
mSATA Interface
5
eIVP1300 AI Mobile NVR
To install a 2.5” SSD:
1. Make sure the NVR is power-off.
2. Unscrew the four screws on the rear panel and then remove the cover from the housing.
3. Screw the SSD to the lower housing cover using the supplied SSD Screws. Find the SATA cable
inside the NVR, and connect the SATA cable to the SATA port on the SSD.
4.
Screw the housing cover back to the NVR.
2.1.1 Storage Compatibility List
Please go to the product page (Download) on EverFocus’ Website www.everfocus.com.tw to see
the latest Storage Compatibility List. It’s recommended to use the storage models listed on the
Storage Compatibility List to ensure your storage devices are compatible.
6
eIVP1300 AI Mobile NVR
2.2 DC Out Cable
The eIVP1300 provides a total of 12V/2A DC output with four sets of power output wires (+/-)
for the connected IP cameras.
Connect the supplied DC Out Cable to the DC Out port on the rear panel of the NVR.
- (black)
+ (black with white stripe)
7
eIVP1300 AI Mobile NVR
Chapter
3
3. AMI BIOS Setup
3.1 System Test and Initialization
The board uses certain routines to perform testing and initialization. If an error, fatal or non-fatal,
is encountered, a few short beeps or an error message will be outputted. The board can usually
continue the boot up sequence with non-fatal errors.
The system configuration verification routines check the current system configuration against the
values stored in the CMOS memory. If they do not match, an error message will be outputted, in
which case you will need to run the BIOS setup program to set the configuration information in
memory.
There are three situations in which you will need to change the CMOS settings:
•
You are starting your system for the first time
•
You have changed your system’s hardware
•
The CMOS memory has lost power and the configuration information is erased
The system’s CMOS memory uses a backup battery for data retention, which is to be replaced
once emptied.
8
eIVP1300 AI Mobile NVR
3.2 AMI BIOS Setup
The AMI BIOS ROM has a pre-installed Setup program that allows users to modify basic system
configurations, which is stored in the batter y-backed CMOS RAM and BIOS NVRAM so that the
information is retained when the power is turned off.
To enter BIOS Setup, press <Del> or <F2> immediately while your computer is powering up.
The function for each interface can be found below.
•
Main – Date and time can be set here. Press <Tab> to switch between date elements
•
Advanced – Enable/ Disable boot option for legacy network devices
•
Chipset – For hosting bridge parameters
•
Boot – Enable/ Disable quiet Boot Option
•
Security – The setup administrator password can be set here
•
Save & Exit –Save your changes and exit the program
3.3 Setup Submenu: Main
Press the “Delete” key to enter the setup page.
9
eIVP1300 AI Mobile NVR
3.4 Setup Submenu: Advanced
3.4.1 Advanced: Power Management
10
eIVP1300 AI Mobile NVR
Options summary:
Power Mode
ATX Type
Optimal Default, Failsafe Default
AT Type
Select power supply mode
Restore AC Power
Power Off
Loss
Power On
Optimal Default, Failsafe Default
Last State
Select AC power state when power is re-applied after a power failure
Enable ACPI Auto
Enable
Disable
Configuration
Enables or Disables BIOS ACPI Auto Configuration
Optimal Default, Failsafe Default
Enable Hibernation
Optimal Default, Failsafe Default
Enable
Disable
Enables or Disables System ability to Hibernate (OS/S4 Sleep State). This option may be
not effective with some OS
ACPI Sleep State
Suspend Disabled
S3 only(Suspend to RAM)
Optimal Default, Failsafe Default
Select highest ACPI sleep state the System will enter when the Suspend button is
pressed
Lock Legacy
Enable
Disable
Resources
Enables or Disables Lock of Legacy Resources
Optimal Default, Failsafe Default
Wake on Ring
Optimal Default, Failsafe Default
Enable
Disable
Enabled/Disabled wake from Ring
Wake on LAN
Enable
Optimal Default, Failsafe Default
Disable
Enabled/Disabled wake from LAN
S5 RTC Wake
Settings
Enable system to wake from S5 using RTC alarm.
11
eIVP1300 AI Mobile NVR
3.4.1.1 Power Management: S5 RTC Wake Settings
Options summary:
Wake system with Fixed Time
Enable
Disable
Optimal Default, Failsafe Default
Enable or disable System wake on alarm event. Wake up time is setting by following
settings.
Wake up day
0-31
Select 0 for daily system wake up 1-31 for which day of the month that you would like
the system to wake up
Wake up hour
0-23
Wake up minute
0-59
Wake up second
0-59
Wake system with Dynamic Time
Enable
Disable
Optimal Default, Failsafe Default
Enable or disable System wake on alarm event. Wake up time is current time + Increase
minutes.
Wake up minute increase
1-15
12
eIVP1300 AI Mobile NVR
3.4.2 Advanced: Super IO Configuration
3.4.2.1 Super IO Configuration: Serial Port 1 Configuration
13
eIVP1300 AI Mobile NVR
3.4.2.2 Super IO Configuration: Serial Port 2 Configuration
3.4.2.3 Super IO Configuration: Serial Port 3 Configuration
14
eIVP1300 AI Mobile NVR
3.4.2.4 Super IO Configuration: Serial Port 4 Configuration
Options summary:
Serial Port
Disabled
Enabled
Default
Allows BIOS to En/Disable correspond serial port.
Change Settings
Auto
(Serial Port 1)
IO=3F8h; IRQ=4;
Default
IO=3F8h;
IRQ=3,4,5,6,7,9,10,11,12;
IO=2F8h;
IRQ=3,4,5,6,7,9,10,11,12;
IO=3E8h;
IRQ=3,4,5,6,7,9,10,11,12;
IO=2E8h;
IRQ=3,4,5,6,7,9,10,11,12;
Allows BIOS to Select Serial Port resource.
Change Settings
Auto
(Serial Port 2)
IO=2F8h; IRQ=3;
Default
IO=3F8h;
IRQ=3,4,5,6,7,9,10,11,12;
15
eIVP1300 AI Mobile NVR
IO=2F8h;
IRQ=3,4,5,6,7,9,10,11,12;
IO=3E8h;
IRQ=3,4,5,6,7,9,10,11,12;
IO=2E8h;
Working model
IRQ=3,4,5,6,7,9,10,11,12;
RS232
Default
RS422
RS485
Select Working model
Change Settings
Auto
(Serial Port 3)
IO=3E8h; IRQ=7;
Default
IO=3F8h;
IRQ=3,4,5,6,7,9,10,11,12;
IO=2F8h;
IRQ=3,4,5,6,7,9,10,11,12;
IO=3E8h;
IRQ=3,4,5,6,7,9,10,11,12;
IO=2E8h;
IRQ=3,4,5,6,7,9,10,11,12;
IO=2F0h;
IRQ=3,4,5,6,7,9,10,11,12;
IO=2E0h;
Working model
IRQ=3,4,5,6,7,9,10,11,12;
RS232
Default
RS422
RS485
Select Working model
Change Settings
Auto
(Serial Port 4)
IO=2E8h; IRQ=7;
Default
IO=3F8h;
IRQ=3,4,5,6,7,9,10,11,12;
IO=2F8h;
IRQ=3,4,5,6,7,9,10,11,12;
IO=3E8h;
IRQ=3,4,5,6,7,9,10,11,12;
16
eIVP1300 AI Mobile NVR
IO=2E8h;
IRQ=3,4,5,6,7,9,10,11,12;
IO=2F0h;
IRQ=3,4,5,6,7,9,10,11,12;
IO=2E0h;
IRQ=3,4,5,6,7,9,10,11,12;
3.4.2.5 Super IO Configuration: Smart Fan Function
Options summary:
Smart Fan Function
Disabled
Enabled
Optimal Default, Failsafe Default
Enabled or Disabled Smart Fan
3.4.2.6 Super IO Configuration: Smart Fan Mode Configuration
Options summary:
Fan 1 Smart Fan Control
Manual RPM
Mode
17
eIVP1300 AI Mobile NVR
Manual Duty
Mode
Auto RPM Mode
Auto Duty-Cycle
Optimal Default, Failsafe Default
Mode
Smart Fan Mode Select
3.4.3 Advanced: Digital IO
Options summary:
Pin 0~7
Input
Optimal Default, Failsafe Default
Output
Set DIO Port 0~7 as Input or Output
Output Level
Low
Optimal Default, Failsafe Default
Hi
Set GPIO Level when used as Output
18
eIVP1300 AI Mobile NVR
3.4.4 Advanced: H/W Monitor
3.4.5 Advanced: CPU Configuration
Options summary:
Intel Virtualization
Disabled
Enabled
Optimal Default, Failsafe Default
Technology
When enabled, a VMM can utilize the additional hardware capabilities provided by Vander pool
Technology
19
eIVP1300 AI Mobile NVR
3.4.5.1 CPU Configuration: Socket 0 CPU Information
3.4.6 Advanced: IDE Configuration
20
eIVP1300 AI Mobile NVR
Options summary:
Serial-ATA(SATA)
Enabled
Default
Disable
SATA Speed Support
Gen1
Gen2
SATA ODD Port
Default
Port0 ODD
Port1 ODD
No ODD
SATA Mode
Default
IDE
AHCI
Default
IDE: Configure SATA controllers as legacy IDE
AHCI: Configure SATA controllers to operate in AHCI mode
Serial-ATA Port0/1
Enabled
Default
Disable
SATA Port0/1 HotPlug
Enabled
Disable
Default
3.4.7 Advanced: CSM Configuration
21
eIVP1300 AI Mobile NVR
Options summary:
CSM Support
Boot option filter
Disable
Enabled
Default
UEFI and Legacy
Default
Legacy only
UEFI only
Storage & Video
Do not launch
UEFI
Other PCI devices
Legacy
Default
UEFI
Default
Legacy
3.4.8 Advanced: Trusted Computing
Options summary:
Security Device Support
Enabled
Disabled
Optimal Default, Failsafe Default
Enabled or Disabled BIOS Support for Security device. O.S. will not show Security
Device. TCG EFI protocol and INT1A interface will not be available
22
eIVP1300 AI Mobile NVR
3.4.9 Advanced: USB Configuration
Options summary:
Legacy USB Support
Enabled
Optimal Default, Failsafe Default
Disabled
Auto
Enables BIOS Support for Legacy USB Support. When enabled, USB can be functional in legacy
environment like DOS.
AUTO option disables legacy support if no USB devices are connected
USB Mass Storage Driver
Disabled
Enabled
Support
Enable/Disable USB Mass Storage Driver Support
Optimal Default, Failsafe Default
Device Name (Emulation
Auto
Optimal Default, Failsafe Default
Type)
Floppy
Forced FDD
Hard Disk
CDROM
If Auto. USB devices less than 530MB will be emulated as Floppy and remaining as
Floppy and remaining as hard drive. Forced FDD option can be used to force a HDD
formatted drive to boot as FDD(Ex. ZIP drive)
23
eIVP1300 AI Mobile NVR
3.4.10 Advanced: Touch Device
Options summary:
Touch Device
Disable
Enable
Default
Help for Touch Device
3.5 Setup Submenu: Chipset
24
eIVP1300 AI Mobile NVR
3.5.1 Chipset: Host Bridge
Options summary:
Primary Boot Display
VBIOS Default
Default
CRT
DP/HDMI
LVDS
25
eIVP1300 AI Mobile NVR
3.5.1.1 CPU Configuration: Socket 0 CPU Information
Options summary:
LVDS
Disabled
Enabled
Default
Enable or Disable LVDS interface
Panel Type
640x480
800x480
800x600
1024x600
Default
1024x768
1280x768
1280x1024
1366x768
1440x900
1600x1200
1920x1080
1920x1200
Select panel resolution.
Color Depth
18-Bit
Default
24-Bit
36-Bit
48-Bit
26
eIVP1300 AI Mobile NVR
Select color depth of the panel
Backlight Type
Normal
Default
Inverted
Select Backlight control type.
Inverted: Brightest for low PWM duty cycle and low voltage. Normal: Brightest for
high PWM duty cycle and high voltage.
Backlight Level
0%
10%
20%
30%
40%
50%
60%
70%
Default
80%
90%
100%
Select Backlight Level
3.5.2 Chipset: South Bridge
27
eIVP1300 AI Mobile NVR
3.5.2.1 South Bridge: Azalia HD Audio
Options summary:
Audio Controller
Disabled
Default
Enabled
Control Detection of the Azalia device.
Disabled = Azalia will be unconditionally disabled. Enabled = Azalia will be
unconditionally Enabled.
Auto = Azalia will be enabled if present disabled other wise.
Azalia HDMI codec
Disabled
Default
Enabled
Enable/Disable internal HDMI codec for Azalia
HDMI Port
Disabled
Default
Enabled
Enable/Disable HDMI Port
28
eIVP1300 AI Mobile NVR
3.5.2.2 South Bridge: USB Configuration
Options summary:
USB OTG Support
PCI mode
Default
Disabled
Enable/Disable USB OTG Support
XHCI Mode
Enabled
Disabled
Default
Auto
Smart Auto
Mode of operation of XHCI controller
USB Per Port Control
Enabled
Default
Disabled
Control each of the USB ports (0~3).
Enable: Enable USB per port
Disable: Use USB port X settings
USB Port0/1/2/3
Enabled
Default
Disabled
Enable/Disable USB Port0/1/2/3
29
eIVP1300 AI Mobile NVR
3.5.2.3 South Bridge: PCI Express Configuration
Options summary:
PCI Express Root Port
Enabled
Optimal Default, Failsafe Default
Disabled
0/1/2/3
Enabling/Disabling the PCI Express root ports
Hot Plug
Disabled
Default
Enabled
Enabling/Disabling the PCI Express Hot Plug
Speed
Auto
Default
Gen2
Gen1
Configure PCIe Port Speed
30
eIVP1300 AI Mobile NVR
3.6 Setup Submenu: Security
Change User/Administrator Password
You can set a User Password once an Administrator Password is set. The password will be required
during boot up, or when the user enters the Setup utility. Please Note that a User Password does
not provide access to many of the features in the Setup utility.
Select the password you wish to set, press Enter to open a dialog box to enter your password (you
can enter no more than six letters or numbers). Press Enter to confirm your entry, after which you
will be prompted to retype your password for a final confirmation. Press Enter again after you
have retyped it correctly.
Removing the Password
Highlight this item and type in the current password. At the next dialog box press Enter to disable
password protection.
31
eIVP1300 AI Mobile NVR
3.7 Setup Submenu: Boot
Options summary:
Launch i210/i211 PXE
Disabled
OpROM
Launch PXE Option Rom
Enabled
Quiet Boot
Disabled
Default
Enabled
Default
En/Disables Quiet Boot option
32
eIVP1300 AI Mobile NVR
3.8 Setup submenu: Exit
33
eIVP1300 AI Mobile NVR
Chapter
6
4. Specification
Model
Processor
Main Memory
Format
Video
Video Input
Video Output
Audio Input
Audio
Audio Output
Format
Recording
Resolution
Internal mSATA
Storage
Removable SSD
RAID
Ethernet
Wi-Fi
Network
3G / 4G
GPS / G-Sensor
eIVP1300
Intel® Atom™ E3845 / E3825 Processor (Default: E3845)
Onboard DDR3L 1066 / 1333 /1600 (Default: 1600MHz 4GB)
H.265 / H.264
IP camera x 4
HDMI x 1, VGA x 1
Mic-in x 1
Line-out x 1
H.265 / H.264
1920 x 1080 at 30fps (NTSC) / 25fps (PAL)
mSATA (half size) x 1 (optional)
2.5’’ SSD x 1 (optional)
N/A
Intel®I211 (or 210) 10/100/1000 based; GbE port x 2
Optional
Optional
Optional
Alarm
Digital I/O
Supports 8-bit digital I/O (optional)
Front I/O Panel
Power button x 1; Reset button x 1; USB2.0 x 2
Remote power x 1
Mic-in x 1
3G/4G/WIFI LED x 3
GbE port (RJ-45) x 2
USB3.0 x 1; USB2.0 x 1
VGA x 1; HDMI x 1
Audio line-out x 1
RS-232 x 2
System
Interface
General
Rear I/O Panel
Expansion Slot
Mini-Card slot x 1 (full-size)
Power Supply
Dimensions
(W x D X H)
Gross Weight
Operating
Storage
Storage Humidity
Vibration/Shock
Certification
DC 9-24V, with ignition pin
7’’ x 7.34” x 2” / 177.8mm x 186.5mm x 50.4mm (without
bracket)
5.7lb (2.6kg)
-32°F ~ 140°F (0°C ~ 60°C); Project base: -40°C ~ 85°C
-40°F ~ 176°F (-40°C ~ 80°C)
0%~90% @40°C, non-condensing
MIL-STD-810G
CE & FCC Class A, RoHS
Note: All specifications are subject to change without notice.
34
EverFocus Electronics Corp.
EverFocus Taiwan:
2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng
Dist., New Taipei City 222, Taiwan
TEL: +886 2 2662 2338
FAX: +886 2 2662 3632
www.everfocus.com.tw
marketing@everfocus.com.tw
EverFocus China - Shenzhen:
3F, Building 7, Longcheng Industrial Park, No.39,
Longguan No.7 Road, Dalang Street, Longhua,
Shenzhen, Guangdong, China
TEL: +86 755 2765 1313
FAX: +86 755 2765 0337
www.everfocus.com.cn
marketing@everfocus.com.cn
EverFocus USA - California:
1801 Highland Avenue, Unit A, Duarte, CA 91010, USA
TEL: +1 626 844 8888
FAX: +1 626 844 8838
www.everfocus.com
sales@everfocus.com
EverFocus Japan:
3F, Kuramochi, Building II, 2-2-3 Koto-Bashi,SumidaKu, Tokyo, 130-0022, Japan
TEL: +81 3 5625 8188
FAX: +81 3 5625 8189
www.everfocus.co.jp
info@everfocus.co.jp
Your EverFocus product is designed and
manufactured with high quality materials
and components which can be recycled
and reused.
This symbol means that electrical and
electronic equipment, at their end-of-life,
should be disposed of separately from
your household waste.
Please, dispose of this equipment at your
local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Ihr EverFocus Produkt wurde entwickelt
und hergestellt mit qualitativ
hochwertigen Materialien und
Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass elektrische
und elektronische Geräte am Ende ihrer
Nutzungsdauer vom Hausmüll getrennt
entsorgt werden sollen.
Bitte entsorgen Sie dieses Gerät bei Ihrer
örtlichen kommunalen Sammelstelle oder
im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!
P/N: 4605EIVP103001A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising