Eizo | FDS1904 | User manual | Eizo FDS1904 User Manual

Eizo FDS1904 User Manual
User’s Manual
Color LCD Monitor
Touch Panel Color LCD Monitor
Important
Please read this User’s Manual, and the Setup Manual (separate
volume) carefully to familiarize yourself with safe and effective usage.
• Please refer to the Setup Manual for basic information ranging from
monitor installation to using the monitor.
• The latest User’s Manual is available for download from our web site:
http://www.eizoglobal.com
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information confidential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specifications are subject to change without notice.
2

Notice for this monitor
This product may not be covered by warranty for uses other than those described in the Setup Manual.
The specifications noted in this manual are only applicable when the following are used:
• Signal cables specified by us
Only use optional products manufactured or specified by us with this product.
It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more
after the monitor power has been turned on, and then adjust the monitor.
Monitors should be set to a lower brilliance to reduce changes in luminosity caused by long-term use and
maintain a stable display.
When the screen image is changed after displaying the same image for extended periods of time, an
afterimage may appear. Use the screen saver or power save function to avoid displaying the same image for
extended periods of time.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer
to “Cleaning” (page 4)).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may
appear on the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994% or higher.
The backlight of the LCD panel has a fixed lifetime. When the screen becomes dark or begins to flicker,
please contact your local EIZO representative.
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do
not attempt to brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation
may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the monitor on. Instead
wait until the dew condensation disappears, otherwise it may cause some damage to the monitor.
(Cautions for the Use of the Touch Panel)
• During touch operation
Be careful of the following points. Otherwise, damage may occur to the monitor.
- Do not strongly press, scratch, or poke the panel.
- Do not touch the panel with hard objects such as ballpoint pens or metals.
Notice for this monitor
3
Cleaning
Attention
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the panel,
and also quality deterioration of the image.
• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the panel.
• Do not allow liquid to enter the clearance between the panel and the panel frame.
The stains on the panel surface can be removed by using the provided cleaning cloth.
To use the monitor comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor
according to the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
4
Notice for this monitor
CONTENTS
Notice for this monitor.......................................... 3
Chapter 4
Cleaning..................................................................... 4
Touch Panel Settings
(FDS1904T / FDU2603WT)............... 24
To use the monitor comfortably.............................. 4
4-1.
Calibrating the Monitor............................... 24
CONTENTS.............................................................. 5
4-2.
Configuring Touch Panel Operation
Settings......................................................... 26
4-3.
Setting Touch Sound................................... 27
Chapter 1
Introduction........................................ 6
1-1.
Features.......................................................... 6
1-2.
EIZO LCD Utility Disk.................................... 7
1-3.
Basic Operations and Functions................. 8
Chapter 5
Power Saving Functions................. 28
●●Disk contents and software overview.............. 7
5-1.
Setting Power Saving.................................. 28
●●Basic Adjustment menu operations................. 8
●●Showing button guide...................................... 9
●●Functions.........................................................10
5-2.
Setting the automatic power off function.... 28
Chapter 6
6-1.
No picture..................................................... 29
6-2.
Imaging problems (for both digital and
analog)........................................................... 30
Setting the Resolution.................................11
6-3.
Imaging problems (for analog only)...........31
Display resolution............................................11
6-4.
Other problems.............................................31
6-5.
Touch panel problems (for FDS1904T /
FDU2603WT only)......................................... 32
Chapter 2
2-1.
Adjusting Screens........................... 11
●●
●●Setting resolution............................................11
2-2.
Displaying Screen Correctly.......................12
●●Digital Signal Input..........................................12
●●Analog Signal Input.........................................12
2-3.
Troubleshooting............................... 29
Adjusting Color.............................................15
●●Adjusting brilliance (brightness)......................15
●●To adjust color temperature............................16
●●To adjust gamma.............................................16
●●To adjust hue...................................................16
●●To adjust color saturation................................17
●●To enhance outline of image...........................17
●●To adjust gain..................................................17
2-4.
Selecting Screen Size..................................18
2-5.
Enabling / Disabling Auto Sharpness........18
Chapter 3
Setting Monitor................................ 19
Chapter 7
Reference......................................... 33
7-1.
Connecting Multiple PCs............................ 33
7-2.
Displaying monitor information................. 35
7-3.
How to Replace the Cooling Fan................ 36
7-4.
Specifications.............................................. 40
●●To switch among input signals....................... 34
●●To set input signal selection........................... 34
●●Displaying signal information......................... 35
●●Displaying monitor information...................... 35
●●FDS1904 / FDS1904-OP............................... 40
●●FDS1904T / FDS1904T-OP............................41
●●FDU2603W / FDU2603W-OP........................ 43
●●FDU2603WT / FDU2603WT-OP................... 44
●●Pin Assignment...............................................47
3-1.
Setting Brightness of Front Button............19
3-2.
Setting Language..........................................19
7-5.
Preset Timing............................................... 49
3-3.
Changing Adjustment Menu Display
Position..........................................................19
7-6.
Optional Accessories.................................. 50
3-4.
Setting the Adjustment Menu orientation.... 20
3-5.
Enabling / Disabling DDC/CI
communication............................................ 20
3-6.
Locking Buttons............................................21
3-7.
Setting Backlight Off Mode.........................21
3-8.
Turning the ECDIS Indicator ON / OFF...... 22
3-9.
Return To Default Setting........................... 23
●●To reset the color adjustment value............... 23
●●To reset all adjustments to the default
Appendix............................................................... 51
Trademark.................................................................51
License......................................................................51
Testing Standard......................................................51
Type Approval of Ship Classification....................51
Warning for Radio interference............................. 52
LIMITED WARRANTY.............................................. 53
Recycling Information............................................ 54
settings........................................................... 23
Resetting Brightness (Brilliance).................... 23
●●
CONTENTS
5
Chapter 1 Introduction
Thank you very much for choosing an EIZO color LCD monitor.
1-1. Features
• 19.0″ LCD (FDS1904 / FDS1904T)
• 25.5″ LCD (FDU2603W / FDU2603WT)
Provides a display area (vertical: over 340 mm) required for radar on large ships.
• Applicable to the resolution of 1280 × 1024. (FDS1904 / FDS1904T)
• Applicable to the resolution of 1920 × 1200. (FDU2603W / FDU2603WT)
• Panel with a wide field of view adopted
-- Horizontal : 178°, vertical : 178°(FDS1904 / FDS1904T)
-- Horizontal : 176°, vertical : 176°(FDU2603W / FDU2603WT)
• Dimming down to the low brightness
The mode allows the user to turn off the backlight.
(You can set the brightness when “Brilliance” in the Adjustment menu is set to the lower limit value.)
See “3-7. Setting Backlight Off Mode” (page 21).
• The buttons on the front of the monitor light up.
The buttons on the front of the monitor (operation buttons) light up orange to enable the monitor to be
operated in a dark environment as well. Their brightness can also be adjusted.
See “3-1. Setting Brightness of Front Button” (page 19).
• Cooling fan replacement is possible.
See “7-3. How to Replace the Cooling Fan” (page 36).
• Built-in warning buzzer
Controlled on the system side.
• Equipped with AC/DC power supplies.
Both AC power input and DC power input are provided to enable installation in various environments. In
addition, connecting both power inputs can provide a helpful backup if the AC power supply fails. (The AC
power supply takes priority during operation when both power inputs are connected.)
• HDCP (High-bandwidth Digital Content Interface)
• Type approval of ship classification
This product is pending approval for the following types of ship classifications.
-----
NK (Nippon Kaiji Kyokai)
DNV (Det Norske Veritas)
ABS (American Bureau of Shipping)
LR (Lloyd’s Register of Shipping)
For the latest information on approvals for ship classifications, please refer to our website.
http://www.eizoglobal.com
• Testing Standards
This product complies with the IEC60945 4th edition standard.
• Optical bonding for increased screen strength and visibility*1
(option: FDS1904-OP / FDS1904T-OP, FDU2603W-OP / FDU2603WT-OP)
*1 A technique in which a layer of resin is used to fill the gap (layer of air) between the LCD panel and clear
panel / touch panel, adhering the two together.
(FDS1904T / FDU2603WT only)
• Touch Panel provided
-- Projected capacitive technology
-- Supports the Windows Touch function (multi-touch) of Windows 10 / Windows 8.1 / Windows 7.
6
Chapter 1 Introduction
1-2. EIZO LCD Utility Disk
An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk
contents and the overview of the software programs.
●●Disk contents and software overview
The disk includes adjustment software, touch panel software, and user’s manuals. Refer to Readme.
txt file on the disk for software startup procedures or file access procedures.
Item
Overview
Screen adjustment pattern files
Touch Panel Driver
*1
Used when adjusting the image of analog signal input manually.
Driver software for the touch panel.*2
* If the following conditions are satisfied, use the standard Windows driver.
• The PC and monitor are connected with a USB cable
• The OS is Windows 8.1 or Windows 7
For setup details please refer to “Chapter 4 Touch Panel Settings
(FDS1904T / FDU2603WT)” (page 24).
TPOffset*1
Software for adjusting the sensitivity of the touch panel*2
Use this software when touch operations are not registered or only
registered after pressing hard.
User’s Manual of this monitor (PDF file)
Readme.txt file
*1 Used only for the FDS1904T / FDU2603WT.
*2 Refer to the corresponding User’s Manual on the CD-ROM for details on installation and use.
Chapter 1 Introduction
7
1-3. Basic Operations and Functions
●●Basic Adjustment menu operations
Note
• The language is set to English in the default settings. To change the language, please refer to “3-2. Setting
Language” (page 19).
1. Displaying Adjustment Menu
1. Press
. The Adjustment menu appears.
Menu title
Current display mode
Item
Settings
Menu
2. Adjusting / Setting
1. Choose a menu to adjust / set with
, and then press
.
2. Choose an item to adjust / set with
, and then press
.
3. Adjust / set the selected item with
8
Chapter 1 Introduction
, and then press
.
3. Exiting
1. Press
a few times. The Adjustment menu finishes.
●●Showing button guide
Press the front buttons other than
, and the button guide appears above the button.
BRILLIANCE
Note
• The Button Guide will continue to appear while the Adjustment menu is showing.
• The Button Guide is displayed differently depending on the selected menu or status.
Chapter 1 Introduction
9
●●Functions
The following table shows all the Adjustment menu’s adjustment and setting menus.
Main menu
Color*1
Setting
Reference
“2-3. Adjusting Color” (page 15)
Brilliance
Temperature*2
Gamma*2
Advanced
Settings
Hue*2
Saturation*2
Outline Enhancer
Gain*2
Screen
Color Reset
“3-9. Return To Default Setting” (page 23)
Screen Size
“2-4. Selecting Screen Size” (page 18)
Analog
Adjustment
Auto Adjustment
“2-2. Displaying Screen Correctly” (page 12)
Range Adjustment
Clock
Phase
Hor.Position
Ver.Position
Power
Manager
Menu Settings
Tools
Power Save
“5-1. Setting Power Saving” (page 28)
Indicator
“3-1. Setting Brightness of Front Button” (page 19)
Eco Timer
“5-2. Setting the automatic power off function”
(page 28)
Language
“3-2. Setting Language” (page 19)
Menu Position
“3-3. Changing Adjustment Menu Display Position”
(page 19)
Input
“To switch among input signals” (page 34)
Input Selection
“To set input signal selection” (page 34)
Auto Sharpness
“2-5. Enabling / Disabling Auto Sharpness” (page 18)
Signal Info
“7-2. Displaying monitor information” (page 35)
Monitor Info
All Reset
“3-9. Return To Default Setting” (page 23)
*1 Depending on which display mode has been applied to the product, the adjustable items under “Color”
may vary.
*2 Adjustments are not possible in the three ECDIS Standard compatible modes (Day, Dusk, Night).
Attention
• Display Mode has three ECDIS Standard compatible modes (Day, Dusk, Night) and a mode where you can
make settings of your choice (Custom). However, the Display Mode cannot be changed using the monitor.
Changes can be made on the system side.
10
Chapter 1 Introduction
Chapter 2 Adjusting Screens
2-1. Setting the Resolution
●●Display resolution
For details on compatible resolutions, refer to “Compatible Resolutions” in the Setup Manual.
●●Setting resolution
When you connect the monitor to the PC and find that the resolution is improper, or when you want to
change the resolution, follow the procedure below.
Windows 10
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Display Settings”.
3. On the “Customize your display” dialog box, click “Advanced display settings”.
4. Select a monitor, then choose a resolution from the “Resolution” pull-down menu.
5. Click the “Apply” button.
6. When a confirmation dialog box is displayed, click “Keep changes”.
Windows 8.1 / Windows 7
1. For Windows 8.1 / Windows 8, click the “Desktop” tile on the Start Screen to display the desktop.
2. Right-click the mouse anywhere on the desktop except for icons.
3. From the displayed menu, click “Screen resolution”.
4. On the “Screen Resolution” dialog box, select the monitor.
5. Click “Resolution” to select the desired resolution.
6. Click the “OK” button.
7. When a confirmation dialog box is displayed, click “Keep changes”.
Windows XP
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Properties”.
3. When the “Display Properties” dialog box is displayed, click the “Settings” tab and select desired
resolution for “Screen resolution” under “Display”.
4. Click the “OK” button to close the dialog box.
Mac OS X
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.
3. On the displayed dialog box, select the “Display” tab and select desired resolution in the
“Resolutions” field.
4. Your selection will be reflected immediately. When you are satisfied with the selected resolution,
close the window.
Chapter 2 Adjusting Screens
11
2-2. Displaying Screen Correctly
●●Digital Signal Input
When digital signals are input, images are displayed correctly based on the preset data of the monitor.
When performing advanced adjustment, see “2-3. Adjusting Color” (page 15) and subsequent pages.
●●Analog Signal Input
Attention
• It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more
after the monitor power has been turned on, and then adjust the monitor.
• The self adjustment function does not work for the images under the vertical resolution of 480 or less.
• The self adjustment and auto adjustment functions work correctly when an image is fully displayed over the
Windows or Macintosh display area. They do not work properly in the cases below:
-- When an image is displayed only on a part of the screen (command prompt window, for example)
-- When a black background (wallpaper, etc.) is in use
Also, these functions cannot work properly in some graphic boards.
The monitor screen adjustment is used to suppress flickering of the screen or adjust screen position
and screen size correctly according to the PC to be used.
Note
• The self adjustment function works when all of the following conditions are satisfied:
-- When a signal is input into the monitor for the first time or when a resolution or vertical / horizontal scan
frequency not used before is set
If the screen is not displayed correctly even after performing the self adjustment operation, adjust the
screen according to the procedures on the following pages to use the monitor comfortably.
12
Chapter 2 Adjusting Screens
Setting Procedures
1. Prepare to use analog screen adjustment patterns.
Load the “EIZO LCD Utility Disk” to your PC, and then open the “Screen adjustment pattern files”.
Note
• For details and instructions on opening the “Screen adjustment pattern files”, refer to the Readme.txt file.
2. Perform the auto adjustment with the analog screen adjustment pattern displayed.
●●To adjust flickering, screen position, and screen size automatically
Procedure
1. Display Pattern 1 in full screen on the monitor using the “Screen adjustment pattern files”.
2. Choose “Screen” from the Adjustment menu, and press
.
3. Choose “Analog Adjustment” from the “Screen” menu, and press
4. Choose “Auto Adjustment”, and press
.
.
The auto adjustment function works (the message “In Progress” appears) to adjust the flickering, screen
position, and screen size correctly.
When the auto adjustment is completed, a message appears. Select “OK” to confirm the new settings or
“Cancel”to restore the previous settings, and press .
If the screen is not displayed correctly even after performing auto adjustment, perform the adjustments
according to the procedures on the following pages. If the screen is displayed correctly, go to “4. Adjusting
color gradation.” (page 15).
Chapter 2 Adjusting Screens
13
3. Perform advanced adjustments for the following using “Analog Adjustment” of
“Screen”.
Adjust the clock, phase and position, in this order.
●●To eliminate vertical bars
Procedure
1. Choose “Clock” from the “Analog Adjustment” menu, and press
2. Adjust the clock with
Press
3. Press
or
or
.
to eliminate vertical bars.
slowly so as not to miss the adjustment point.
to exit the adjustment.
When blurring, flickering or bars appear on the screen after adjustment, proceed to “To remove flickering or
blurring” to remove flickering or blurring.
●●To remove flickering or blurring
Procedure
1. Choose “Phase” from the “Analog Adjustment” menu, and press
2. Adjust the phase with
3. Press
or
.
to minimize flickering or blurring.
to exit the adjustment.
Attention
• Flickering or blurring may not be eliminated depending on your PC or graphics board.
●●To correct the screen position
Note
• Since the number of pixels and the pixel positions are fixed on the LCD monitor, only one position is provided
to display images correctly. The position adjustment is made to shift an image to the correct position.
Procedure
1. Choose “Hor.Position” or “Ver.Position” from the “Analog Adjustment” menu, and press
2. Adjust the position with
3. Press
or
.
.
to exit the adjustment.
When vertical bars appear on the screen after adjustment, go back to “To eliminate vertical bars”. (Clock →
Phase → Position)
4. Close Pattern 1.
14
Chapter 2 Adjusting Screens
4. Adjusting color gradation.
●●To adjust color gradation automatically
Every color gradation (0 to 255) can be displayed by adjusting the signal output level.
Procedure
1. Display Pattern 2 in full screen on the monitor using the “Screen adjustment pattern files”.
2. Choose “Screen” from the Adjustment menu, and press
.
3. Choose “Analog Adjustment” from the “Screen” menu, and press
.
4. Choose “Range Adjustment” from the “Analog Adjustment” menu, and press
.
The color gradation is adjusted automatically.
When the auto adjustment is completed, a message appears. Select “OK” to confirm the new settings or
“Cancel” to restore the precious settings, and press .
5. Close Pattern 2.
2-3. Adjusting Color
Attention
• It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more after
the monitor power has been turned on, and then adjust the monitor.
• The same image may be seen in different colors on multiple monitors due to their monitor-specific characteristics.
Make fine color adjustment visually when matching colors on multiple monitors.
Note
• The values shown in “%” or “K” are available only as reference.
●●Adjusting brilliance (brightness)
The screen brightness is adjusted by changing the brightness of the backlight (light source from the
LCD back panel).
Adjustable range
1 to 100%
0 to 100%
when “Backlight Off Mode” is set to “Off” (page 21)
when “Backlight Off Mode” is set to “On” (page 21)
(When the lower limit value (0%) is set, tthe backlight is turned off to darken the screen.)
Procedure
1. Choose “Color” from the Adjustment menu, and press
2. Choose “brilliance” from “Color”, and press
3. Use
4. Press
or
.
.
for adjustment.
to exit.
Note
• The brightness can be set by directly pressing
or (For the setting value, please display and check “Color”.)
• When adjusting brilliance by long pressing
or , adjustment terminates when the default setting is
reached. You can continue adjustment by pressing
or
again (When “ECDIS indicator” is “ON”, and the
monitor Display Mode is set to “Day”, “Dusk”, “Night”.)
Chapter 2 Adjusting Screens
15
●●To adjust color temperature
The color temperature can be adjusted.
The color temperature is normally used to express the hue of “White” and/or “Black” by a numerical
value. The value is expressed in degrees “K” (Kelvin).
The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like
the flame temperature. The gain preset values are set for each color temperature setting value.
Adjustable range
Native, 4000K-10000K (specified by every 500K unit, including 9300K)
Procedure
.
1. Choose “Color” from the Adjustment menu, and press
2. Choose “Temperature” from “Color”, and press
3. Use
or
.
for adjustment.
to exit.
4. Press
Note
• “Gain” allows you to perform more advanced adjustment (see “To adjust gain” (page 17)).
• If you set “Native”, the image is displayed in the preset color of the monitor (Gain: 100% for each RGB).
• When gain is changed, the color temperature is changed to “User”.
●●To adjust gamma
Gamma can be adjusted. The brightness of the monitor varies depending on the input signal,
however, the variation rate is not proportional to the input signal. To keep the balance between the
input signal and the brightness of the monitor is called as “Gamma correction”.
Adjustable range
1.8, 2.0, 2.2, 2.4, 2.6
Procedure
.
1. Choose “Color” from the Adjustment menu, and press
2. Choose “Gamma” from “Color”, and press
3. Use
or
.
for adjustment.
to exit.
4. Press
●●To adjust hue
This function allows you to adjust the hue.
Adjustable range
-100 to 100
Procedure
.
1. Choose “Color” from the Adjustment menu, and press
2. Choose “Advanced Settings” from “Color”, and press
3. Choose “Hue”, and press
4. Use
5. Press
or
.
.
for adjustment.
to exit.
Attention
• Using this function may make some color gradations unavailable for display.
16
Chapter 2 Adjusting Screens
●●To adjust color saturation
This function allows you to adjust color saturation.
Adjustable range
-100 to 100
Procedure
.
1. Choose “Color” from the Adjustment menu, and press
2. Choose “Advanced Settings” from “Color”, and press
3. Choose “Saturation”, and press
4. Use
or
.
.
for adjustment.
to exit.
5. Press
Attention
• Using this function may make some color gradations unavailable for display.
Note
• The minimum value (-100) changes the screen to monochrome.
●●To enhance outline of image
OutlineEnhancer functions to emphasize outline of the images by emphasizing the color difference
between pixels composing the images. This may improve the texture of the material and its feel of the
images. On the contrary, it also functions to reproduce the images smoothly by gradating its outline.
Procedure
.
1. Choose “Color” from the Adjustment menu, and press
2. Choose “Advanced Settings” from “Color”, and press
3. Choose “Outline Enhancer”, and press
.
.
4. Select the display status in the range from -3 to 3 (soft to sharp) with
or
as desired.
to exit.
5. Press
●●To adjust gain
The brightness of each color component red, green, and blue is called “Gain”. You can change the
hue of “white” by adjusting gain.
Adjustable range
0 to 100%
Procedure
.
1. Choose “Color” from the Adjustment menu, and press
2. Choose “Advanced Settings” from “Color”, and press
3. Choose “Gain”, and press
.
.
4. Choose the color to adjust from “Red”, “Green”, and “Blue”, and then press
5. Use
6. Press
or
.
for adjustment.
to exit.
Attention
• Using this function may make some color gradations unavailable for display.
Note
• The value of gain changes with that of color temperature.
• When gain is changed, the color temperature is changed to “User”.
Chapter 2 Adjusting Screens
17
2-4. Selecting Screen Size
The image with the resolution other than the recommended resolution is displayed in full screen
automatically. You can change the screen size by using the “Screen Size” function from “Screen”.
Setting
Function
Full
Displays an image in full screen. Images are distorted in some cases because the vertical rate is not
equal to the horizontal rate.
Enlarged
Displays an image in full screen. In some cases, a blank horizontal or vertical border appears to
equalize the vertical rate and the horizontal rate.
Normal
Displays images with the specified resolution.
Example: Image size 1024 × 768
FDS1904 / FDS1904T:
FDU2603W / FDU2603WT:
Full
Enlarged
Normal
(1280×1024)
(1920×1200)
(1280×960)
(1600×1200)
(1024×768)
(1024×768)
Procedure
.
1. Choose “Screen” from the Adjustment menu, and press
.
2. Choose “Screen Size” from “Screen”, and press
3. Select “Full”, “Enlarged”, or “Normal” with
4. Press
or
.
to exit.
Attention
• Selecting “Normal” may make some color gradations unavailable for display.
2-5. Enabling / Disabling Auto Sharpness
By enabling Auto Sharpness outlines will be adjusted according to the displayed image which can
improve its feel and texture.
Procedure
1. Choose “Tools” from the Adjustment menu, and press
2. Choose “Auto Sharpness” from “Tools”, and press
3. Select “On” or “Off” with
4. Press
or
.
.
.
to exit.
Note
• The extent of adjustment depends on the setting value of “Outline Enhancer”.
18
Chapter 2 Adjusting Screens
Chapter 3 Setting Monitor
3-1. Setting Brightness of Front Button
The brightness of the front buttons (control button and power button) can be set.
Attention
• They are set to light up under the following condition, and are set to “4” by default.
-- Power button: When the power cord is connected to the power outlet.
-- Control button: When the power button is turned on.
Procedure
.
1. Choose “PowerManager” from the Adjustment menu, and press
2. Choose “Indicator” from “PowerManager”, and press
.
or
3. Set the brightness so it is in the range from 1 to 7 with
4. Press
as desired.
to exit.
3-2. Setting Language
This function allows you to select a language for the Adjustment menu and messages.
Selectable languages
English,German,French,Spanish,Italian,Swedish,Japanese,Simplified Chinese,Traditional Chinese
Procedure
1. Choose “Menu Settings” from the Adjustment menu, and press
2. Choose “Language” from “Menu Settings”, and press
3. Select a language with
4. Press
or
.
.
.
to exit.
3-3. Changing Adjustment Menu Display Position
You can change the display position of the Adjustment menu.
Procedure
1. Choose “Menu Settings” from the Adjustment menu, and press
2. Choose “Menu Position” from “Menu Settings”, and press
3. Choose the position with
4. Press
or
.
.
.
to exit.
Chapter 3 Setting Monitor
19
3-4. Setting the Adjustment Menu orientation
When the monitor is set to the portrait display mode, the orientation of the Adjustment Menu can be
changed as well.
Default setting: Landscape
Procedure
for five seconds or more to turn off the monitor.
1. Press
down, press
2. Holding
for at least two seconds to turn on the monitor.
The “Optional Settings” menu appears.
3. Choose “Orientation” from “Optional Settings”, and press
4. Select “Landscape” or “Portrait” with
5. Select “Finish” with
6. Press
or
or
, and press
.
.
.
.
The “Optional Settings” menu is closed.
Note
• When using the monitor screen in a portrait position, the graphics board supporting portrait display is
required. When placing the monitor in a portrait position, the settings of your graphics board need to be
changed. Refer to the User’s Manual of the graphics board for details.
3-5. Enabling / Disabling DDC/CI communication
This function allows you to enable / disable the DDC/CI communication.
Procedure
for five seconds or more to turn off the monitor.
1. Press
down, press
2. Holding
for at least two seconds to turn on the monitor.
The “Optional Settings” menu appears.
3. Choose “DDC/CI” from “Optional Settings”, and press
4. Select “On” or “Off” with
5. Select “Finish” with
6. Press
or
or
, and press
.
.
The “Optional Settings” menu is closed.
20
Chapter 3 Setting Monitor
.
.
3-6. Locking Buttons
This function allows you to lock the adjusted / set status to prevent changing them.
Procedure
for five seconds or more to turn off the monitor.
1. Press
down, press
2. Holding
for at least two seconds to turn on the monitor.
The “Optional Settings” menu appears.
3. Choose “Key Lock” from “Optional Settings”, and press
4. Choose “Off”, “Menu”, or “All” with
Settings
Off
(Default setting)
, and press
.
Buttons that can be locked
None (All buttons are enabled)
Menu
button
All
All buttons excluding
5. Select “Finish” with
6. Press
or
.
or
.
.
The “Optional Settings” menu is closed.
Note
• If buttons are pressed while locked, “Locked” is displayed on the screen.
3-7. Setting Backlight Off Mode
This function allows you to set the condition when “Brilliance” is set to the lower limit value.
Setting
Function
On
When “Brilliance” is set to the lower limit value, the backlight is turned off to darken the screen.
(However, this excludes when the Adjustment menu, “Signal Error”, or the EIZO logo are displayed)
Off
Even when “Brilliance” is set to the lower limit value, the screen is not darkened.
Procedure
for five seconds or more to turn off the monitor.
1. Press
down, press
2. Holding
for at least two seconds to turn on the monitor.
The “Optional Settings” menu appears.
3. Choose “Backlight Off Mode” from “Optional Settings”, and press
4. Select “On” or “Off” with
5. Select “Finish” with
6. Press
or
or
, and press
.
.
.
.
The “Optional Settings” menu is closed.
Chapter 3 Setting Monitor
21
3-8. Turning the ECDIS Indicator ON / OFF
The ECDIS Indicator will light up when this setting is set to ON. Please use this as a guide to adjust the
monitor brightness.
ECDIS Indicator
Monitor status
The monitor brilliance is set to the ECDIS adjustment value.
The monitor brilliance is set higher than the ECDIS adjustment value.
The monitor brilliance is set lower than the ECDIS adjustment value.
The ECDIS Indicator does not light up in the following cases.
• The “ECDIS Indicator” is “OFF”
• It deviates significantly from the ECDIS adjustment value
• The correct code has not been entered
Attention
• The ECDIS Indicator becomes active when the monitor display mode is set to “Day”, “Dusk” or “Night”.
• The Display Mode cannot be changed using the monitor. Changes can be made on the system side.
Procedure
for five seconds or more to turn off the monitor.
1. Press
down, press
2. Holding
for at least two seconds to turn on the monitor.
The “Optional Settings” menu appears.
3. Choose “ECDIS Indicator” from “Optional Settings”, and press
4. Select “On” or “Off” with
5. Select “Finish” with
6. Press
or
or
, and press
.
.
The “Optional Settings” menu is closed.
22
Chapter 3 Setting Monitor
.
.
3-9. Return To Default Setting
There are two different Resets: Color Reset for only resetting the color adjustments to the default settings
and All Reset for resetting all settings to the defaults. There is also a function to reset the screen
brightness to the default value.
Attention
• After resetting, you cannot undo the operation.
Note
• Regarding the default setting, see “Main Default Settings” (page 45).
●●To reset the color adjustment value
This function only resets the color adjustment value for the currently selected mode to the default
settings.
Procedure
1. Choose “Color” from the Adjustment menu, and press
2. Choose “Color Reset” from “Color”, and press
3. Choose “Execute” with
4. Press
or
.
.
.
.
The color adjustments revert to the default settings.
●●To reset all adjustments to the default settings
This function resets all adjustments to the default settings (except the “Input” and “Optional Settings”
menu).
Procedure
1. Choose “Tools” from the Adjustment menu, and press
2. Choose “All Reset” from “Tools”, and press
3. Select “Execute” with
4. Press
or
.
.
.
.
All settings excluding the “Input” and “Optional Settings” menu are reset to the default settings.
●●Resetting Brightness (Brilliance)
Reset the setting value for the screen brightness (brilliance) to the default setting.
Attention
• Settings cannot be recovered once this function is executed.
Procedure
1. Press
while holding down
or
on the front of the monitor.
The setting value for the screen brightness (brilliance) is reset to the default setting.
Chapter 3 Setting Monitor
23
Chapter 4 Touch Panel Settings
(FDS1904T / FDU2603WT)
This chapter explains the settings for when the FDS1904T / FDU2603WT is used in an environment that
satisfies the following conditions.
• The PC and monitor are connected with a USB cable
• The OS is Windows 8.1 / Windows 7
Attention
• If using the FDS1904T / FDU2603WT in either of the following environments, see the Touch Panel Driver User’s
Manual (on the CD-ROM).
-- The PC and monitor are connected with a USB cable, and the OS being used is Windows 10 / Windows XP
-- The PC and monitor are connected with a RS-232C cable
4-1. Calibrating the Monitor
Attention
• Do not put your hands or any metal close to the screen because the screen is susceptible to the dielectric object.
• If a “User Account Control” dialog box is displayed during operation, proceed according to the displayed instructions.
1. Open the Windows Control Panel.
The method for opening the Control Panel differs depending on the OS.
Windows 8.1
1. Click
at the bottom of the “Start” screen.
The “Apps” screen appears.
2. Click “Control Panel” under “Windows System”.
Windows 7
1. Click “Start” - “Control Panel”.
24
Chapter 4 Touch Panel Settings (FDS1904T / FDU2603WT)
2. Click “Hardware and Sound” - “Tablet PC Settings”.
“Tablet PC Settings” window appears.
3. Click “Setup” in the “Display” tab.
A touchscreen specification screen with a white background is displayed.
Attention
• If using the monitor in a multiple monitor environment, specify the touchscreen according to the message
displayed on screen.
4. Touch the screen with your finger.
The touched screen is recognized as a touchscreen.
5. Press “Enter” on the keyboard.
The “Tablet PC Settings” window reappears.
6. Click “Calibrate”.
A calibration screen with a white background is displayed.
Attention
• If using the monitor in a multiple monitor environment, select the monitor for calibration from the “Display”
pulldown menu and then click “Calibrate”.
7. Touch the calibration target (cross) for a few seconds with your finger and release.
The calibration target appears on the screen 16 times, starting from the top left to top right and then
down to the bottom left to bottom right.
Note
• For second or subsequent calibrations, the calibration target appears 4 times.
8. After completing calibration, click “Yes” to save the calibration data.
9. Click “OK” to close the window.
Chapter 4 Touch Panel Settings (FDS1904T / FDU2603WT)
25
4-2. Configuring Touch Panel Operation Settings
1. Open the Windows Control Panel.
The method for opening the Control Panel differs depending on the OS (see page 24).
2. Click “Hardware and Sound” - “Pen and Touch”.
“Pen and Touch” window appears.
Configure the touch panel operation settings in the “Pen and Touch” window. For detailed settings,
refer to the settings on each tab and Windows Help.
3. After completing settings, click “OK” to close the window.
26
Chapter 4 Touch Panel Settings (FDS1904T / FDU2603WT)
4-3. Setting Touch Sound
The sound output when the screen is touched can be changed or turned off.
1. Open the Windows Control Panel.
The method for opening the Control Panel differs depending on the OS (see page 24).
2. Click “Hardware and Sound” - “Sound” - “Change system sounds”.
“Sound” window appears.
3. Select “Start Navigation” from the “Program Events” list.
4. Select the sound to output when the screen is touched from the “Sounds” pulldown menu.
Note
• Select “None” to turn off touch sound.
5. Click “OK” to close the window.
Chapter 4 Touch Panel Settings (FDS1904T / FDU2603WT)
27
Chapter 5 Power Saving Functions
5-1. Setting Power Saving
This function allows you to set the monitor into the power saving mode according to the PC status. When
the monitor has shifted to the power saving mode, the images on the screen are not displayed.
Attention
• For the maximum power saving, it is recommended that the Power button be turned off.
• Five seconds before the monitor enters the power saving mode, it displays a preliminary message.
Procedure
1. Choose “PowerManager” from the Adjustment menu, and press
.
2. Choose “Power Save” from “PowerManager”, and press
3. Select “On” or “Off” with
4. Press
or
.
.
to exit.
Power Saving System
At Analog signal input
This monitor complies with the “VESA DPM” standard.
PC
Monitor
ON
Operating
Power saving mode
STAND-BY
SUSPENDED
OFF
Power saving mode
At Digital signal input
This monitor complies with the “DVI DMPM” standard.
The monitor enters the power saving mode after five seconds in connection with the PC setting.
PC
Monitor
ON
Operating
Power saving mode
Power saving mode
Exiting the power saving mode
If the monitor receives input, it automatically exits the power saving mode and returns to the normal
display mode.
5-2. Setting the automatic power off function
This function allows you to specify whether to turn on / off the monitor automatically after a specified time
has elapsed in the power saving mode.
Adjustable range
Off, 0, 1, 2, 3, 4, 5, 10, 15, 20, 25, 30, 45 min, 1, 2, 3, 4, 5 h
Procedure
1. Choose “PowerManager” from the Adjustment menu, and press
2. Choose “Eco Timer” from “PowerManager”, and press
3. Select “Off” or time to turn off the monitor with
4. Press
28
to exit.
Chapter 5 Power Saving Functions
or
.
.
.
Chapter 6 Troubleshooting
If a problem still remains after applying the suggested remedies, contact your EIZO representative.
6-1. No picture
Problem
1. No picture
• None of the operation buttons light up.
• Only the
button lights up orange.
• All of the operation buttons light up orange.
2. The message below appears.
Possible cause and remedy
• Check whether the power cord is connected properly.
• Turn the main power switch on.
• Turn off the main power, and then turn it on again a few
minutes later.
• Press
.
• Adjust the brightness (brilliance) of the screen.
• Operate the mouse or keyboard.
• Check whether the PC is turned on.
This message appears when the signal is not input correctly
even when the monitor functions properly.
• This message appears when no signal is
input.
Example:
• The message shown left may appear, because some PCs
do not output the signal soon after power-on.
• Check whether the PC is turned on.
• Check whether the signal cable is connected properly.
• Switch the input signal (see “To switch among input
signals” (page 34)).
• The message shows that the input signal is
out of the specified frequency range. (Such
signal frequency is displayed in magenta.)
Example:
• Check whether the PC is configured to meet the resolution
and vertical scan frequency requirements of the monitor.
(“Compatible Resolutions” in the Setup Manual.)
• Reboot the PC.
• Select an appropriate display mode using the graphics
board’s utility. Refer to the User’s Manual of the graphics
board for details.
fD: Dot clock
(Displayed only during digital signal input)
fH: Horizontal scan frequency
fV: Vertical scan frequency
Chapter 6 Troubleshooting
29
6-2. Imaging problems (for both digital and analog)
Problem
30
Possible cause and remedy
1. The screen is too bright or too dark.
• Use “Brilliance” in the Adjustment menu to adjust it. (The LCD
monitor backlight has a limited life span. When the screen
becomes dark or begins to flicker, contact your local dealer.)
2. The screen suddenly became dark. / The
“Brilliance” value in the Adjustment menu
cannot be increased.
• The monitor always monitors its internal temperature.
If the internal monitor reaches a high temperature and
exceeds the specified value, the monitor will automatically
enter the following state to decrease the temperature.
--The “Brilliance” setting is lowered
--The “Brilliance” setting cannot be increased
This state will return to the original when the internal
temperature decreases.
If the internal temperature increases further even after the
“Brilliance” setting is decreased, a “WARNING” message
is displayed and the monitor power is automatically turned
off. (Power indicator flashes green.)
3. Characters are blurred.
• Check whether the PC is configured to meet the resolution
and vertical scan frequency requirements of the monitor.
(“Compatible Resolutions” in the Setup Manual.)
• Use “Outline Enhancer” in the Adjustment menu to adjust
it (see “To enhance outline of image” (page 17)).
4. Afterimages appear.
• Afterimages are particular to LCD monitors. Avoid
displaying the same image for a long time.
• Use the screen saver or power saving function to avoid
displaying the same image for extended periods of time.
5. Green / red / blue / white dots or defective
dots remain on the screen.
• This is due to LCD panel characteristics and is not a failure.
6. Interference patterns or pressure marks
remain on the screen.
• Leave the monitor with a white or black screen. The
symptom may disappear.
7. Noise appears on the screen.
• When entering the signals of HDCP system, the normal
images may not be displayed immediately.
8. Cloudiness cannot be removed even
after wiping the screen. / There is dew
condensation on the interior side of the
glass.
• When cloudiness cannot be removed even by wiping
the screen, dew condensation may have occurred on
the interior side of the glass that protects the panel. In
this case, turn on the monitor and display something
on screen. The dew condensation will disappear after
a while. Also, warming the glass using a hair dryer may
make the dew condensation disappear more quickly. Dew
condensation appearing like this on the interior side of the
glass will not lead to product failure or degradation.
Chapter 6 Troubleshooting
6-3. Imaging problems (for analog only)
Problem
Possible cause and remedy
1. Display position is incorrect.
• Use “Position” in the Adjustment menu to correct the image
position (see “To correct the screen position” (page 14)).
• If the problem persists, use the graphics board’s utility if
available to change the display position.
2. Vertical bars appear on the screen or a
part of the image is flickering.
• Use “Clock” in the Adjustment menu to adjust it
(see “To eliminate vertical bars” (page 14)).
3. Whole screen is flickering or blurring.
• Use “Phase” in the Adjustment menu to adjust it
(see “To remove flickering or blurring” (page 14)).
6-4. Other problems
Problem
Possible cause and remedy
1. The message below appears on screen.
• This message appears when the monitor’s cooling fan is
not operating correctly. Check the state of the cooling fan
on the rear of the monitor.
2. The Adjustment menu does not appear.
• Check whether the operation lock function works
(see “3-6. Locking Buttons” (page 21)).
• If the function is active, “Locked” is displayed on the screen.
3. The fan is noisy.
• This product is fitted with a cooling fan to keep the internal
temperature from rising. Depending on the monitor’s location
the fan may be audible when operating, but this is not a defect.
Chapter 6 Troubleshooting
31
6-5. Touch panel problems (for FDS1904T / FDU2603WT only)
Problem
Possible cause and remedy
1. Touch operation is disabled.
• Check that the monitor and PC are connected with a USB
or RS-232C cable.
• Turn off and on the monitor.
• Check that the power cord of the monitor and PC is
connected to a grounded main outlet. Failure to ground
the equipment may result in malfunction.
• Perform touch panel sensitivity adjustment using TPOffset.
2. Cursor position is not correct. / Cursor
jumps.
• Connect the monitor to the PC with the cable indicated in
the Setup Manual. The touch panel may not work correctly
if a conversion adapter is used.
• Turn off and on the monitor.
• Calibrate the screen again.
• Check that the power cord of the monitor and PC is
connected to a grounded main outlet. Failure to ground
the equipment may result in malfunction.
• Perform touch panel sensitivity adjustment using TPOffset.
• Changing the position or angle of the monitor may cause
the cursor to jump.
• Keep metals away from the panel surface.
• If the touch panel is dirty, the touch panel may not operate
properly. See “Cleaning” (page 4) to clean the touch panel.
• The spray for preventing static electricity may influences
the sensitivity of the touch panel.
• Do not touch the touch panel for 5 seconds after the PC
starts up, after turning on the monitor, or after connecting
the cable. Touching the touch panel too soon may cause
incorrect cursor positioning or disable touch operation.
If this occurs, either leave the touch panel untouched for
approximately 2 minutes or turn the monitor off and on
again. If the problem persists, calibrate the screen again.
3. The cursor does not appear at the touched
position and instead is displayed at a pointsymmetric position with respect to the center
of the screen.
• Calibrate the screen again.
4. Cursor is jittery. / Drawing lines are not
straight and smooth.
• Check that the power cord of the monitor and PC is
connected to a grounded main outlet. Failure to ground
the equipment may result in malfunction.
• Perform touch panel sensitivity adjustment using TPOffset.
• The influence of metal may cause jittery cursor.
• When multiple monitors are placed close to each other,
leave space between monitors.
5. (If the OS being used is Windows 8.1 /
Windows 7)
Calibration does not work correctly.
• Reset the touch panel to the state before calibration (by
clicking “Reset” in the “Display” tab of the “Tablet PC
Settings” window accessible from the Windows Control
Panel) and then calibrate the touch panel again.
6. (If the OS being used is Windows 8.1 /
Windows 7)
No touch-sound.
• Sound is only output through the audio output terminal of
the PC. To hear touch sound, connect speakers.
• Sound is not output when touched positions are not
assigned any functions.
Attention
• For details on TPOffset (software for adjusting touch panel sensitivity), see the TPOffset User’s Manual (on the
CD-ROM).
32
Chapter 6 Troubleshooting
Chapter 7 Reference
7-1. Connecting Multiple PCs
The product has multiple connections to PCs and allows you to switch to one of the connections for display.
Attention
• It is assumed the touch panel monitor will be used with one computer. When the monitor is to be connected to
multiple computers, connect a RS-232C cable to the computer used for touch operation (one unit only).
Connection examples
D-Sub mini 15-pin
connector
DVI-D connector
Analog
Digital
Signal cable
(option MD-C87)
Signal cable
(option DD200)
D-Sub mini 15-pin
connector
To PC 1
DVI connector
To PC 2
Chapter 7 Reference
33
●●To switch among input signals
Procedure
1. Choose “Tools” from the Adjustment menu, and press
2. Choose “Input” from “Tools”, and press
3. Select “D-SUB” or “DVI” with
4. Press
or
.
.
.
to exit.
●●To set input signal selection
Setting
Function
Auto
The monitor recognizes the connector through which PC signals are input.
When a PC is turned off or enters the power saving mode, the monitor automatically displays
another signal.
Manual
The monitor detects only the PC’s signals currently displaying automatically. Select an active
input signal in the Adjustment menu.
Procedure
1. Choose “Tools” from the Adjustment menu, and press
2. Choose “Input Selection” from “Tools”, and press
3. Select “Auto” or “Manual” with
4. Press
or
.
.
.
to exit.
Note
• When “Auto” is selected for “Input Selection”, the monitor’s power saving function works only when all PCs
are in the power saving mode.
34
Chapter 7 Reference
7-2. Displaying monitor information
●●Displaying signal information
This function displays the information about the current input signals displayed.
Procedure
1. Choose “Tools” from the Adjustment menu, and press
2. Choose “Signal Info” from “Tools”, and press
.
.
The “Signal Info” appears.
(Example)
●●Displaying monitor information
This function displays the information about the monitor.
Procedure
1. Choose “Tools” from the Adjustment menu, and press
2. Choose “Monitor Info” from “Tools”, and press
.
.
The “Monitor Info” appears.
The product name, serial number, DDC/CI settings, firmware version and usage time are displayed.
(Example)
Attention
• The usage time is not always “0” when you purchase the monitor due to factory inspection.
Chapter 7 Reference
35
7-3. How to Replace the Cooling Fan
The cooling fan in this product can be replaced according to the following procedure.
Attention
• Be sure to follow the procedure when replacing the fan. Note that EIZO Corporation assumes no responsibility for
any damages caused due to improper handling of this product.
Note
• Please contact your local EIZO representative for replacement parts.
Procedure
1. Remove the monitor from its enclosure.
1. Remove the screws that secure the monitor to the enclosure.
2. Lay the LCD monitor on a soft cloth spread over on a stable surface with the panel surface facing down.
2. Remove the fan cover.
Remove the four screws that secure the cover.
FDS1904 / FDS1904T
FDU2603W / FDU2603WT
36
Chapter 7 Reference
3. Remove the fan.
1. Disconnect the cables connected to the monitor.
2. Remove the four screws that secure the fan.
Attention
• Make sure to hold the connector when removing the cable. Pulling on the cable may damage the connector.
1.
2.
Connector
FDS1904 / FDS1904T
1.
1.
Connector
Connector
2.
2.
FDU2603W / FDU2603WT
Chapter 7 Reference
37
4. Install the new fan.
Attention
• Take care when handling the fan. Dropping or imparting physical shocks to the fan may damage it.
• Pay attention to the orientation of the fan when installing it.
1. Fix the fan to the monitor using the screws removed in step 3 (page 37) (recommended torque:
8.0 ± 2kgf•cm / 0.78 ± 0.2 N•m).
2. Connect the cable to the monitor.
Securely connect the connector to the monitor.
2.
1.
Connector
Orient the label
surface outwards
FDS1904 / FDS1904T
1.
1.
2.
2.
Orient the label
surface outwards
Connector
Connector
FDU2603W / FDU2603WT
38
Chapter 7 Reference
5. Install the fan cover.
Fix the cover to the monitor using the screws removed in step 2 (page 36).
Attention
• Orient the air outlets downwards when installing the cover.
Air outlets
FDS1904 / FDS1904T
Air outlets
FDU2603W / FDU2603WT
6. Install the monitor into the enclosure.
Chapter 7 Reference
39
7-4. Specifications
●●FDS1904 / FDS1904-OP
LCD Panel
Type
VA
Backlight
LED
Size
48 cm (19.0 inch) (48.1 cm diagonal)
Native Resolution
1280 dots × 1024 lines
Display Size (H x V)
376.3 mm × 301.0 mm
Pixel Pitch
0.294 mm
Display Colors
Approx. 16.77 million colors
Viewing Angles
(H / V, typical)
178˚ / 178˚
Maximum brightness FDS1904:
(brilliance)
FDS1904-OP:
590 cd/m2
600 cd/m2
Contrast ratio (typical) 2000:1
Response Time (typical) 20 ms (Black-white-black)
Protective glass
Video Signals
Surface treatment
Surface hardness
5H
Input Terminals
DVI-D connector × 1, D-Sub mini 15-pin × 1
Output terminal
D-Sub mini 15-pin × 1
Digital Scanning
Frequency (H / V)
31 kHz - 64 kHz / 59Hz - 61Hz (720 × 400: 69Hz - 71Hz)
Analog Scanning
Frequency (H / V)
31 kHz - 80 kHz / 56 Hz - 76Hz
Dot Clock
Digital
108 MHz
Analog
135 MHz
Synchronous signal
Separate, TTL, positive / negative
Composite, TTL, positive / negative
Sync on Green, 0.5Vp-p, negative
Communication
Input Terminals
RS-232C:
Power
Input
AC
DC
Physical
Specifications
40
Anti-reflection
D-Sub 9-pin (female)
Rating AC 100 - 240 V (Operating: AC 85 V - 264 V),50/60 Hz, 0.65 A - 0.3 A
Rating DC +24 V (Operating: +30% / -10%), 2.7 A (DC 24 V)
Maximum Power
Consumption
64 W or less
Power Save
Mode
AC
9.0 W or less
DC
6.0 W or less
Standby Mode AC
7.0 W or less
DC
5.0 W or less
(When there is DVI input, no USB device is connected,
and “Input Selection” is set to “Manual”,
and when DDC/CI is OFF)
(When there is DVI input, no USB device is connected,
and “Input Selection” is set to “Manual”,
and when DDC/CI is OFF)
Dimensions
429 mm × 406 mm × 74.5 mm (excluding the projection)
Net Weight
FDS1904:
Approx. 5.9 kg
FDS1904-OP:
Approx. 6.2 kg
Operating
Environmental
Requirements
Temperature:
-15˚C to 55˚C
Humidity
10% to 90% R.H. (no condensation)
Transportation /
Storage
Environmental
Requirements
Temperature
-20˚C to 60˚C
Humidity
10% to 92% R.H. (no condensation)
Viewing distance (Recommended)
1014 mm or more (*Based on IEC 62288)
Protection structure
Front: IP65, Rear: IP22 (Landscape only)
Chapter 7 Reference
●●FDS1904T / FDS1904T-OP
LCD Panel
Type
VA
Backlight
LED
Size
48 cm (19.0 inch) (48.1 cm diagonal)
Resolution
1280 dots × 1024 lines
Display Size (H x V)
376.3 mm × 301.0 mm
Pixel Pitch
0.294 mm
Display Colors
Approx. 16.77 million colors
Viewing Angles
(H / V, typical)
178˚ / 178˚
Maximum brightness
(brilliance)
FDS1904T:
540 cd/m2
FDS1904T-OP:
580 cd/m2
Contrast ratio (typical)
2000:1
Response Time (typical) 20 ms (Black-white-black)
Touch Panel
Method
Projected capacitive technology
Communication method USB, RS-232C (* Cannot be used at the same time.)
Surface treatment
Anti-reflection, Anti-fingerprint
Surface hardness
5H
OS
Microsoft Windows 10 (32 bit / 64 bit)
Microsoft Windows 8.1 (32 bit / 64 bit)
Microsoft Windows 7 Service Pack 1 (32 bit / 64 bit)
Microsoft Windows XP Service Pack 3 (32 bit)
(Not compatible with Mac OS)
Number of simultaneous Up to 5 (Microsoft Windows XP only supports single point touch)
touch points
Video Signals
Input Terminals
DVI-D connector × 1, D-Sub mini 15-pin × 1
Output terminal
D-Sub mini 15-pin × 1
Digital Scanning
Frequency (H / V)
31 kHz - 64 kHz / 59 Hz - 61 Hz (720 × 400: 69 Hz - 71 Hz)
Analog Scanning
Frequency (H / V)
31 kHz - 80 kHz / 56Hz - 76Hz
Dot Clock
Digital
108 MHz
Analog
135 MHz
Synchronous signal
Separate, TTL, positive / negative
Composite, TTL, positive / negative
Sync on Green, 0.5 Vp-p, negative
Communication Input Terminals
RS-232C:
D-Sub 9-pin (female)
RS-232C:
D-Sub 9-pin (male)
USB
Upstream port × 1
Port
Standard
Power supply
Input
USB Specification Revision 2.0
AC
DC
Maximum Power
Consumption
Rating AC 100 - 240 V (Operating: AC 85 V - 264 V), 50/60 Hz, 0.65 A - 0.3 A
Rating DC +24 V (Operating: +30% / -10%), 2.7 A (DC 24 V)
64 W or less
Power Save
Mode
AC
9.0 W or less
DC
6.0 W or less
Standby Mode
AC
7.0 W or less
DC
5.0 W or less
(When there is DVI input, no USB device is connected,
and “Input Selection” is set to “Manual”,
and when DDC/CI is OFF)
(When there is DVI input, no USB device is connected,
and “Input Selection” is set to “Manual”,
and when DDC/CI is OFF)
Chapter 7 Reference
41
Physical
Specifications
Operating
Environmental
Requirements
42
Dimensions
429 mm × 406 mm × 74.5 mm (excluding the projection)
Net Weight
FDS1904T:
Approx. 6.4 kg
FDS1904T-OP:
Approx. 6.7 kg
Temperature:
-15˚C to 55˚C
Humidity
10% to 90% R.H. (no condensation)
Transportation / Temperature
Storage
Humidity
Environmental
Requirements
-20˚C to 60˚C
Viewing distance (Recommended)
1014 mm or more (*Based on IEC 62288)
Protection structure
Front: IP65, Rear: IP22 (Landscape only)
Chapter 7 Reference
10% to 92% R.H. (no condensation)
●●FDU2603W / FDU2603W-OP
LCD Panel
Type
VA
Backlight
LED
Size
65 cm (25.5 inch) (64.8 cm diagonal)
Native Resolution
1920 dots × 1200 lines
Display Size (H x V)
550.0 mm × 343.8 mm
Pixel Pitch
0.2865 mm
Display Colors
Approx. 16.77 million colors
Viewing Angles
(H / V, typical)
176˚ / 176˚
Maximum brightness FDU2603W:
490 cd/m2
(brilliance)
FDU2603WT-OP: 500 cd/m2
Contrast ratio (typical) 1500:1
Response Time (typical) 20 ms (Black-white-black)
Protective glass
Video Signals
Surface treatment
Anti-reflection
Surface hardness
5H
Input Terminals
DVI-D connector × 1, D-Sub mini 15-pin × 1
Output terminal
D-Sub mini 15-pin × 1
Digital Scanning
Frequency (H / V)
31 kHz - 76 kHz / 59 Hz - 61 Hz (720 × 400: 69 Hz - 71 Hz)
Analog Scanning
Frequency (H / V)
31 kHz - 81 kHz / 56 Hz - 76 Hz
Dot Clock
Digital
162 MHz
Analog
162 MHz
Synchronous signal
Separate, TTL, positive / negative
Composite, TTL, positive / negative
Sync on Green, 0.3 Vp-p, negative
Communication
Input Terminals
RS-232C:
Power
Input
D-Sub 9-pin (female)
AC
Rating AC 100 - 240 V (Operating: AC 85 V - 264 V),
50/60 Hz, 1.2 A - 0.6 A
DC
Rating DC +24 V (Operating: +30% / -10%), 4.5 A (DC 24 V)
108 W or less
Maximum Power
Consumption
Power Save
Mode
AC
10.0 W or less
DC
7.0 W or less
Standby Mode
AC
10.0 W or less
DC
7.0 W or less
Physical
Specifications
Dimensions
624 mm × 456 mm × 86 mm (excluding the projection)
Net Weight
FDU2603W:
Approx. 14.5 kg
FDU2603W-OP:
Approx. 14.9 kg
Operating
Environmental
Requirements
Temperature:
-15˚C to 55˚C
Humidity
10% to 90% R.H. (no condensation)
Transportation /
Storage
Environmental
Requirements
Temperature
-20˚C to 60˚C
Humidity
10% to 90% R.H. (no condensation, wet bulb temperature ≤ 39 °C)
Viewing distance (Recommended)
988 mm or more (*Based on IEC 62288)
Protection structure
Front: IP65, Rear: IP22
Chapter 7 Reference
43
●●FDU2603WT / FDU2603WT-OP
LCD Panel
Type
VA
Backlight
LED
Size
65 cm (25.5 inch) (64.8 cm diagonal)
Native Resolution
1920 dots × 1200 lines
Display Size (H x V)
550.0 mm × 343.8 mm
Pixel Pitch
0.2865 mm
Display Colors
Approx. 16.77 million colors
Viewing Angles
(H / V, typical)
176˚ / 176˚
Maximum brightness FDU2603WT:
470 cd/m2
(brilliance)
FDU2603WT-OP: 500 cd/m2
Contrast ratio (typical) 1500:1
Response Time (typical) 20 ms (Black-white-black)
Touch Panel
Method
Projected capacitive technology
Communication method USB, RS-232C (* Cannot be used at the same time.)
Surface treatment
Anti-reflection
Surface hardness
5H
OS
Microsoft Windows 10 (32 bit / 64 bit)
Microsoft Windows 8.1 (32 bit / 64 bit)
Microsoft Windows 7 Service Pack 1 (32 bit / 64 bit)
Microsoft Windows XP Service Pack 3 (32 bit)
(Not compatible with Mac OS)
Number of simultaneous Up to 5 (Microsoft Windows XP only supports single point touch)
touch points
Video Signals
Communication
USB
Power
Input Terminals
DVI-D connector × 1, D-Sub mini 15-pin × 1
Output terminal
D-Sub mini 15-pin × 1
Digital Scanning
Frequency (H / V)
31 kHz - 76 kHz / 59 Hz - 61 Hz (720 × 400: 69 Hz - 71 Hz)
Analog Scanning
Frequency (H / V)
31 kHz - 81 kHz / 56 Hz - 76 Hz
Dot Clock
Digital
162 MHz
Analog
162 MHz
Synchronous signal
Separate, TTL, positive / negative
Composite, TTL, positive / negative
Sync on Green, 0.3 Vp-p, negative
Input Terminals
RS-232C:
D-Sub 9-pin (female)
RS-232C:
D-Sub 9-pin (male)
Port
Upstream port × 1
Standard
USB Specification Revision 2.0
Input
AC
Rating AC 100 - 240 V (Operating: AC 85 V - 264 V),
50/60 Hz, 1.2 A - 0.6 A
DC
Rating DC +24 V (Operating: +30% / -10%), 4.5 A (DC 24 V)
108 W or less
Maximum Power
Consumption
Physical
Specifications
Power Save
Mode
AC
10.0 W or less
DC
7.0 W or less
Standby Mode
AC
10.0 W or less
DC
7.0 W or less
Dimensions
624 mm × 456 mm × 86 mm (excluding the projection)
Net Weight
FDU2603WT:
Approx. 15.1 kg
FDU2603WT-OP: Approx. 15.9 kg
44
Chapter 7 Reference
Operating
Environmental
Requirements
Transportation /
Storage
Environmental
Requirements
Temperature:
-15˚C to 55˚C
Humidity
10% to 90% R.H. (no condensation)
Temperature
-20˚C to 60˚C
Humidity
10% to 90% R.H. (no condensation, wet bulb temperature ≤ 39 °C)
Viewing distance (Recommended)
988 mm or more (*Based on IEC 62288)
Protection structure
Front: IP65, Rear: IP22
Main Default Settings
Brilliance
FDS1904 / FDS1904T
FDU2603W / FDU2603WT
1-Custom:
100% (255/255)
2-Day:
65% (166/255)
3-Dusk:
56% (144/255)
4-Night:
11% (28/255)
1-Custom:
100% (255/255)
2-Day:
67% (171/255)
3-Dusk:
60% (153/255)
4-Night:
11% (27/255)
Screen Size
Enlarged
Power Save
Off
Power Indicator
4
Eco Timer
Off
Language
English
Menu Position
Center
Input
*1
D-SUB
Input Selection
Auto
Key Lock*1
Off
DDC/CI
*1
On
*1
Landscape
Orientation
Backlight Off Mode*1
ECDIS Indicator
*1,*2
On
On
*1 These functions cannot be initialized with the “All Reset” function (see “3-9. Return To Default Setting”
(page 23)).
*2 The ECDIS Indicator becomes active when the monitor display mode is set to “Day”, “Dusk” or “Night”.
Chapter 7 Reference
45
Outside Dimensions
●●FDS1904 / FDS1904T
Unit: mm
429
376.32
26.34
74.5 4
100
100
52.47
362
301.06
406
52.47
26.34
(for FDS1904T only)
●●FDU2603W / FDU2603WT
37
624
550
3.2
593
Unit: mm
15.5
37
M6×8
562
90
138.5 70
406
86
30
25
56
30
32
344
456
90
32
56
Display area
13.5
86
15.5
(for FDU2603WT only)
46
Chapter 7 Reference
●●Pin Assignment
D-Sub mini 15-pin connector
5
4
10 9
3 2
8 7
1
6
15 14 13 12 11
Pin No.
1
2
3
4
5
Signal
Pin No.
Signal
Pin No.
Red Video
Green Video
Blue Video
Ground
NC
6
7
8
9
10
Signal
Pin No.
Signal
Pin No.
Red Video Ground
Green Video Ground
Blue Video Ground
NC
Ground
11
12
13
14
15
Signal
Ground
Data (SDA)
H.Sync
V.Sync
Clock (SCL)
(NC: Not connected)
DVI-D connector
Pin No.
1
2
3
4
5
6
7
T.M.D.S. Data 2T.M.D.S. Data 2+
T.M.D.S. Data2/4 Shield
NC
NC
DDC Clock (SCL)
DDC Data (SDA)
8
Analog Vertical Sync
9
10
11
12
13
14
15
16
T.M.D.S. Data1T.M.D.S. Data1+
T.M.D.S. Data1/3 Shield
NC
NC
+5V Power
Ground (return for +5V,
Hsync and Vsync)
Hot Plug Detect
Signal
17
18
19
20
21
22
23
T.M.D.S. Data0T.M.D.S. Data0+
T.M.D.S. Data0/5 Shield
NC
NC
T.M.D.S. Clock shield
T.M.D.S. Clock+
24
T.M.D.S. Clock(NC: Not connected)
USB port
• Upstream (Series B)
Pin No.
1
2
3
4
Signal
VBUS
-Data
+Data
Ground
Remarks
Cable power
Serial data
Serial data
Cable ground
Chapter 7 Reference
47
RS-232C port
• D-Sub 9-pin (female, for monitor control)
Pin No.
1
2
3
DCD
RXD
TXD
Signal
Pin No.
4
5
6
DTR
GND
DSR
Signal
Pin No.
7
8
9
RTS
CTS
RI
Signal
Attention
• The monitor is the DCE side.
• Use a straight-through cable (male to female) to connect with the PC.
• D-Sub 9-pin (male, for touch panel control)
Pin No.
1
2
3
DCD
RXD
TXD
Signal
Pin No.
4
5
6
DTR
GND
DSR
Signal
Attention
• The monitor is the DTE side.
• Use a crossover cable (female to female) to connect with the PC.
48
Chapter 7 Reference
Pin No.
7
8
9
RTS
CTS
RI
Signal
7-5. Preset Timing
The following table shows factory preset analog signal timing:
Attention
• Display position may be deviated depending on the PC connected, which may require screen adjustment using Adjustment menu.
• If a signal other than those listed in the table is input, adjust the screen using the Adjustment menu. However,
screen display may still be incorrect even after the adjustment.
• When interlace signals are used, the screen cannot be displayed correctly even after screen adjustment using the
Adjustment menu.
FDS1904 / FDS1904T
Resolution
Frequency
Dot Clock: MHz
Horizontal:kHz
Vertical: Hz
25.18
31.50
31.50
28.32
36.00
40.00
50.00
49.50
65.00
75.00
78.75
108.00
94.20
107.50
108.00
108.00
117.00
135.00
31.47
37.86
37.50
31.47
35.16
37.88
48.08
46.88
48.36
56.48
60.02
67.50
61.97
71.86
60.00
63.98
71.69
79.98
59.94
72.81
75.00
70.09
56.25
60.32
72.19
75.00
60.00
70.07
75.03
75.00
66.14
76.20
60.00
60.02
67.19
75.03
640 × 480
640 × 480
640 × 480
720 × 400
800 × 600
800 × 600
800 × 600
800 × 600
1024 × 768
1024 × 768
1024 × 768
1152 × 864
1152 × 900
1152 × 900
1280 × 960
1280 × 1024
1280 × 1024
1280 × 1024
FDU2603W / FDU2603WT
Resolution
640 x 480
640 x 480
640 x 480
720 x 400
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1152 x 900
1152 x 900
1280 x 960
1280 x 1024
1280 x 1024
1280 x 1024
1600 x 1200
1600 x 1200
1680 x 1050
1920 x 1200
Frequency
Dot Clock: MHz
Horizontal:kHz
Vertical: Hz
25.18
31.50
31.50
28.32
36.00
40.00
50.00
49.50
65.00
75.00
78.75
108.00
94.20
107.50
108.00
108.00
117.00
135.00
162.00
130.25
146.25
154.00
31.47
37.86
37.50
31.47
35.16
37.88
48.08
46.88
48.36
56.48
60.02
67.50
61.97
71.86
60.00
63.98
71.69
79.98
75.00
74.00
65.29
74.04
59.94
72.81
75.00
70.09
56.25
60.32
72.19
75.00
60.00
70.07
75.03
75.00
66.14
76.20
60.00
60.02
67.19
75.03
60.00
59.92
59.95
59.95
Chapter 7 Reference
49
7-6. Optional Accessories
The following accessories are available separately.
Tilt Stand
MDS-T261 (for FDU2603W / FDU2603W-OP / FDU2603WT / FDU2603WT-OP)
MDS-T191 (for FDS1904 / FDS1904-OP / FDS1904T / FDS1904T-OP)
Note
• The following types of ship classifications are pending approval.
-- NK (Nippon Kaiji Kyokai)
-- DNV GL (DNV GL AS)
-- ABS (American Bureau of Shipping)
-- LR (Lloyd’s Register of Shipping)
50
Chapter 7 Reference
Appendix
Trademark
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing, LLC in the United States and other countries.
The DisplayPort Compliance Logo and VESA are registered trademarks of the Video Electronics
Standards Association.
The SuperSpeed USB Trident Logo is a registered trademark of USB Implementers
Forum, Inc.
Kensington and Microsaver are registered trademarks of ACCO Brands Corporation.
Thunderbolt is a trademark of Intel Corporation in the United States and/or other countries.
Microsoft, Windows and Windows Vista are registered trademarks of Microsoft Corporation in the United
States and other countries.
Adobe is a registered trademark of Adobe Systems Incorporated in the United States and other
countries.
Apple, macOS, Mac OS, OS X, Macintosh and ColorSync are registered trademarks of Apple Inc.
Ethernet is a registered trademark of Fuji Xerox Co., Ltd.
EIZO, the EIZO Logo, ColorEdge, DuraVision, FlexScan, FORIS, RadiCS, RadiForce, RadiNET, Raptor
and ScreenManager are registered trademarks of EIZO Corporation in Japan and other countries.
ColorEdge Tablet Controller, ColorNavigator, CuratOR, EcoView NET, EIZO EasyPIX, EIZO Monitor
Configurator, EIZO ScreenSlicer, G-Ignition, i • Sound, Quick Color Match, RadiLight, Re/Vue, Screen
Administrator, Screen InStyle and UniColor Pro are trademarks of EIZO Corporation.
All other company and product names are trademarks or registered trademarks of their respective
owners.
License
The bitmap font used for this product is designed by Ricoh Industrial Solutions Inc.
Testing Standard
This product complies with the IEC60945 4th edition standard.
Equipment category: b) protected from the weather
Type Approval of Ship Classification
This product is pending approval for the following types of ship classifications.
•• NK (Nippon Kaiji Kyokai)
•• DNV GL (DNV GL AS)
•• ABS (American Bureau of Shipping)
•• LR (Lloyd’s Register of Shipping)
* For the latest information on approvals for ship classifications, please refer to our website.
http://www.eizoglobal.com
Appendix
51
Warning for Radio interference
For Europe, Australia, New Zealand, etc Only
Warning
Operation of this equipment in a residential environment could cause radio interference.
Warnung
Der Betrieb dieses Geräts in einer Wohnumgebung konnte Funkstörungen verursachen.
Avertissement
L’utilisation de cet équipement dans une zone résidentielle pourrait provoquer des interférences radio.
52
Appendix
LIMITED WARRANTY
EIZO Corporation (hereinafter referred to as “EIZO”) and distributors authorized by EIZO (hereinafter referred to as the
“Distributors”) warrant, subject to and in accordance with the terms of this limited warranty (hereinafter referred to as the
“Warranty”), to the original purchaser (hereinafter referred to as the “Original Purchaser”) who purchased the product
specified in this document (hereinafter referred to as the “Product”) from EIZO or Distributors, that EIZO and Distributors
shall, at their sole discretion, either repair or replace the Product at no charge if the Original Purchaser becomes aware
within the Warranty Period (defined below) that the Product malfunctions or is damaged in the course of normal use of
the Product in accordance with the description in the instruction manual attached to the Product (hereinafter referred to
as the “User’s Manual”).
The period of this Warranty is three (3) years from the date of purchase of the Product (hereinafter referred to as the
“Warranty Period”). EIZO and Distributors shall bear no liability or obligation with regard to the Product in relation to the
Original Purchaser or any third parties other than as provided under this Warranty.
EIZO and Distributors will cease to hold or store any parts (excluding design parts) of the Product upon expiration of ten
(10) years after the production of the Product is discontinued. In repairing the monitor, EIZO and Distributors will use
renewal parts which comply with our QC standards. If the unit cannot be repaired due to its condition or the stockout of
a relevant part, EIZO and Distributors may offer the replacement by a product with equivalent performance instead of
repairing it.
The Warranty is valid only in the countries or territories where the Distributors are located. The Warranty does not restrict
any legal rights of the Original Purchaser.
Notwithstanding any other provision of this Warranty, EIZO and Distributors shall have no obligation under this Warranty
whatsoever in any of the cases as set forth below:
(a) Any defect of the Product caused by freight damage, modification, alteration, abuse, misuse, accident, incorrect
installation, disaster, faulty maintenance and/or improper repair by third party other than EIZO and Distributors;
(b) Any incompatibility of the Product due to possible technical innovations and/or regulations;
(c) Any deterioration of the sensor;
(d) Any defect of the Product caused by external equipment;
(e) Any defect of the Product on which the original serial number has been altered or removed;
(f) Any normal deterioration of the product, particularly that of consumables, accessories, and/or attachments (e.g.
buttons, rotating parts, cables, User’s Manual, etc.);
(g) Any deformation, discoloration, and/or warp of the exterior of the product including that of the surface of the LCD
panel;
(h) Any defect of the Product caused by placement in a location where it may be affected by strong vibration or shocks;
(i) Any defect of the Product caused by liquid leaking from battery; and
(j) Any deterioration of display performance caused by the deterioration of expendable parts such as the LCD panel
and/or backlight, etc. (e.g. changes in brightness, changes in brightness uniformity, changes in color, changes in
color uniformity, defects in pixels including burnt pixels, etc.).
To obtain service under the Warranty, the Original Purchaser must deliver the Product, freight prepaid, in its original
package or other adequate package affording an equal degree of protection, assuming the risk of damage and/or loss
in transit, to the local Distributor. The Original Purchaser must present proof of purchase of the Product and the date of
such purchase when requesting services under the Warranty.
The Warranty Period for any replaced and/or repaired product under this Warranty shall expire at the end of the original
Warranty Period.
EIZO OR DISTRIBUTORS ARE NOT RESPONSIBLE FOR ANY DAMAGE TO, OR LOSS OF, DATA OR OTHER
INFORMATION STORED IN ANY MEDIA OR ANY PART OF ANY PRODUCT RETURNED TO EIZO OR DISTRIBUTORS
FOR REPAIR.
EIZO AND DISTRIBUTORS MAKE NO FURTHER WARRANTIES, EXPRESSED OR IMPLIED, WITH RESPECT TO
THE PRODUCT AND ITS QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR
USE. IN NO EVENT SHALL EIZO OR DISTRIBUTORS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL,
CONSEQUENTIAL OR OTHER DAMAGE WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR
LOSS OF PROFIT, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR ANY OTHER PECUNIARY
LOSS) ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT OR IN ANY CONNECTION WITH THE
PRODUCT, WHETHER BASED ON CONTRACT, TORT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, EVEN
IF EIZO OR DISTRIBUTORS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THIS EXCLUSION
ALSO INCLUDES ANY LIABILITY WHICH MAY ARISE OUT OF THIRD PARTY CLAIMS AGAINST THE ORIGINAL
PURCHASER. THE ESSENCE OF THIS PROVISION IS TO LIMIT THE POTENTIAL LIABILITY OF EIZO AND
DISTRIBUTORS ARISING OUT OF THIS LIMITED WARRANTY AND/OR SALES.
Appendix
53
Recycling Information
Recycling Information
This product, when disposed of, is supposed to be collected and recycled according to your country’s
legislation to reduce environmental burden. When you dispose of this product, please contact a distributor or
an affiliate in your country.
The contact addressees are listed on the EIZO website below.
http://www.eizoglobal.com
For recycling information for customers in Switzerland, please refer to the following website.
http://www.swico.ch
Informationen zum Thema Recycling
Dieses Produkt muss gemäß den Vorschriften Ihres Landes zur Entlastung der Umwelt recyclet werden.
Wenden Sie sich bei der Entsorgung dieses Produkts an einen Verteiler oder eine Tochtergesellschaft in
Ihrem Land.
Die Adressen zur Kontaktaufnahme sind auf der unten angegebenen Website von EIZO aufgeführt.
http://www.eizoglobal.com
Kunden in der Schweiz entnehmen Informationen zum Recycling der folgenden Website:
http://www.swico.ch
Informations sur le recyclage
Ce produit doit être jeté aux points de collecte prévus à cet effet et recyclé conformément à la législation de
votre pays, afin de réduire l’impact sur l’environnement. Lorsque vous jetez ce produit, veuillez contacter un
distributeur ou une société affiliée de votre pays.
Les adresses des distributeurs sont répertoriées sur le site Web EIZO ci-dessous.
http://www.eizoglobal.com
Pour les clients en Suisse, veuillez consulter le site Web suivant afin d’obtenir des informations sur le
recyclage.
http://www.swico.ch
Información sobre reciclaje
Este producto debe desecharse y reciclarse según la legislación del país para reducir el impacto
medioambiental. Cuando desee deshacerse de este producto, póngase en contacto con un distribuidor o
una filial de su país.
Encontrará las direcciones de contacto en el sitio web de EIZO que se indica a continuación.
http://www.eizoglobal.com
Informazioni sul riciclaggio
Per lo smaltimento e il riciclaggio del presente prodotto, attenersi alle normative vigenti nel proprio paese per
ridurre l’impatto ambientale. Per lo smaltimento, rivolgersi ad un distributore o un affiliato presenti nel proprio
paese.
Gli indirizzi sono elencati nel sito Web EIZO riportato di seguito.
http://www.eizoglobal.com
Per informazioni sul riciclaggio per i clienti in Svizzera, consultare il sito Web riportato di seguito.
http://www.swico.ch
Återvinningsinformation
När denna produkt kasseras ska den hanteras och återvinnas enligt landets föreskrifter för att reducera
miljöpåverkan. När du kasserar produkten ska du kontakta en distributör eller representant i ditt land.
Kontaktadresserna listas på EIZO-webbplatsen nedan.
http://www.eizoglobal.com
54
Appendix
Πληροφορίες ανακύκλωσης
Το προϊόν αυτό, όταν απορρίπτεται, πρέπει να συλλέγεται και να ανακυκλώνεται σύμφωνα με τη νομοθεσία
της χώρας σας έτσι ώστε να μην επιβαρύνει το περιβάλλον. Για να απορρίψετε το προϊόν, επικοινωνήστε με
έναν αντιπρόσωπο ή μια θυγατρική εταιρεία στη χώρα σας.
Οι διευθύνσεις επικοινωνίας αναγράφονται στην τοποθεσία web της EIZO παρακάτω.
http://www.eizoglobal.com
Сведения по утилизации
По истечении срока службы данного продукта его следует принести на сборный пункт и
утилизировать в соответствии с действующими предписаниями в вашей стране, чтобы уменьшить
вредное воздействие на окружающую среду. Прежде чем выбросить данный продукт, обратитесь к
дистрибьютору или в местное представительство компании в вашей стране.
Контактные адреса можно найти на веб-узле EIZO.
http://www.eizoglobal.com
Informatie over recycling
Wanneer u dit product wilt weggooien, moet het uit milieu-overwegingen worden verzameld en gerecycled
volgens de betreffende wetgeving van uw land. Wanneer u dit product wilt weggooien, moet u contact
opnemen met een distributeur of een partner in uw land.
De contactadressen worden vermeld op de volgende EIZO-website.
http://www.eizoglobal.com
Informação sobre reciclagem
Este produto, quando o deitar fora, deve ser recolhido e reciclado de acordo com a legislação do seu país
para reduzir a poluição. Quando deitar fora este produto, contacte um distribuidor ou uma filial no seu país.
Os endereços de contacto estão listados no website do EIZO, abaixo.
http://www.eizoglobal.com
Oplysninger om genbrug
Dette produkt forventes ved bortskaffelse at blive indsamlet og genbrugt i overensstemmelse med
lovgivningen i dit land for at reducere belastningen af miljøet. Når du bortskaffer denne produkt, skal du
kontakte en distributør eller et tilknyttet selskab i dit land.
Adresserne på kontaktpersonerne er angivet på EIZO’s websted nedenfor.
http://www.eizoglobal.com
Kierrätystä koskevia tietoja
Tuote tulee hävittää kierrättämällä maan lainsäädännön mukaisesti ympäristön kuormittumisen
vähentämiseksi. Kun hävität tuotteen, ota yhteyttä jälleenmyyjään tai tytäryhtiöön maassasi.
Yhteystiedot löytyvät EIZOn Internet-sivustolta.
http://www.eizoglobal.com
Wykorzystanie surowców wtórnych
Ten produkt po zużyciu powinien być zbierany i przetwarzany zgodnie z krajowymi przepisami dotyczącymi
ochrony środowiska. Wyrzucając ten produkt, należy skontaktować się z lokalnym dystrybutorem lub
partnerem. Adresy kontaktowe można znaleźć we wskazanej poniżej witrynie internetowej firmy EIZO.
http://www.eizoglobal.com
Appendix
55
Informace o recyklaci
Při likvidaci produktu musí být produkt vyzvednut a recyklován podle zákonů příslušné země, aby
nedocházelo k zatěžování životního prostředí. Zbavujete-li se produktu, kontaktujte distributora nebo
pobočku ve své zemi. Kontaktní adresy jsou uvedeny na následující webové stránce společnosti EIZO.
http://www.eizoglobal.com
Ringlussevõtu alane teave
Keskkonnakoormuse vähendamiseks tuleks kasutatud tooted kokku koguda ja võtta ringlusse vastavalt teie
riigi seadustele. Kui kõrvaldate käesoleva toote, võtke palun ühendust turustaja või filiaaliga oma riigis.
Kontaktisikud on toodud EIZO veebilehel järgmisel aadressil:
http://www.eizoglobal.com
Újrahasznosítási információ
Jelen terméket, amikor eldobjuk, az illető ország törvényei alapján kell összegyűjteni és újrahasznosítani,
hogy csökkentsük a környezet terhelését. Amikor ezt a terméket eldobja, kérjük lépjen kapcsolatba egy
országon belüli forgalmazóval vagy társvállalkozással.
A kapcsolat címei az EIZO alábbi weboldalán találhatók felsorolva:
http://www.eizoglobal.com
Podatki o recikliranju
Ob koncu uporabe odslužen izdelek izročite na zbirno mesto za recikliranje v skladu z okoljevarstveno
zakonodajo vaše države. Prosimo, da se pri odstranjevanju izdelka obrnete na lokalnega distributerja ali
podružnico.
Kontaktni naslovi so objavljeni na spodaj navedenih spletnih straneh EIZO:
http://www.eizoglobal.com
Informácie o recyklácii
Pri likvidácii musí byť tento výrobok recyklovaný v súlade s legislatívou vašej krajiny, aby sa znížilo zaťaženie
životného prostredia. Keď sa chcete zbaviť tohto výrobku, kontaktujte prosím distribútora alebo pobočku vo
vašej krajine.
Zoznam kontaktných adries je uvedený na nasledovnej webovej stránke firmy EIZO:
http://www.eizoglobal.com
Pārstrādes informācija
Utilizējot šo produktu, tā savākšana un pārstrāde veicama atbilstoši jūsu valsts likumdošanas prasībām
attiecībā uz slodzes uz vidi samazināšanu. Lai veiktu šī produkta utilizāciju, sazinieties ar izplatītāju vai
pārstāvniecību jūsu valstī.
Kontaktadreses ir norādītas zemāk minētajā EIZO tīmekļa vietnē.
http://www.eizoglobal.com
Informacija apie grąžinamąjį perdirbimą
Šalinant (išmetant) šiuos gaminius juos reikia surinkti ir perdirbti grąžinamuoju būdu pagal jūsų šalies teisės
aktus, siekiant sumažinti aplinkos teršimą. Kai reikia išmesti šį gaminį, kreipkitės į jūsų šalyje veikiančią
gaminių pardavimo atstovybę arba jos filialą.
Kontaktiniai adresatai nurodyti EIZO interneto svetainėje.
http://www.eizoglobal.com
56
Appendix
Информация относно рециклиране
При изхвърлянето на този продукт се предлага събирането и рециклирането му съобразно законите на
вашата страна за да се намали замърсяването на околната среда. Когато искате да се освободите от
този продукт, моля свържете се с търговския му представител или със съответните органи отговарящи
за това във вашата страна.
Данните за връзка с нас са описани на следния Интернет сайт на EIZO:
http://www.eizoglobal.com
Informaţie referitoare la reciclare
Acest produs, când debarasat, trebuie colectat şi reciclat conform legislaţiei ţării rspective ca să reducem
sarcina mediului. Când se debarasează de acest produs, vă rugăm să contactaţi un distribuitor sau un afiliat
al ţării respective.
Adresele de contact le găsiţi pe pagina de web al EIZO:
http://www.eizoglobal.com
http://www.eizoglobal.com
Geri Dönüşüm Bilgisi
Bu ürünün, atılacağı zaman, ülkenizin çevre kirliliğinin azaltılması konusundaki mevzuatına göre toplanması
ve yeniden değerlendirilmesi gerekmektedir. Ürünü atacağınız zaman lütfen ülkenizdeki bir distribütör veya
ilgili kuruluşla temasa geçiniz.
İrtibat adresleri aşağıdaki EIZO web sitesinde verilmiştir.
http://www.eizoglobal.com
Appendix
57
4th Edition-September, 2017
Copyright © 2014-2017 EIZO Corporation. All rights reserved.
03V25044D1
(U.M-FDS1904)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising