Eizo | FDF2304W-IP | Owner Manual | Eizo FDF2304W-IP Owner Manual

Eizo FDF2304W-IP Owner Manual
Installation Manual
Color LCD Monitor
Important
Please read this Installation Manual, the Instruction Manual and the
Setup Manual carefully to familiarize yourself with safe and effective
usage.
• For the latest product information including the User’s Manual, refer
to our web site: http://www.eizoglobal.com
About this manual
Setup Manual
Describes precautions and setup processes from network camera
connection to camera image display.
Instruction Manual
Describes operation of network cameras and live image screen
menus, etc.
Installation Manual
Describes network camera registration and function setup, monitor
system setup, etc.
(this manual)
This product has been adjusted specifically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specifications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information confidential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specifications are subject to change without notice.
2

Notice for this monitor
This product is suited for displaying surveillance camera images.
This product has been adjusted specifically for use in the region to which it was originally shipped. If the
product is used outside the region, it may not operate as specified in the specifications.
This product may not be covered by warranty for uses other than those described in this manual.
The specifications noted in this manual are only applicable when the following are used:
• Power cords provided with the product
• Signal cables specified by us
Only use optional products manufactured or specified by us with this product.
When installing the monitor in a rack, ensure that there is adequate space around the sides, back and top of
the monitor.
If you place this product on a lacquer-coated desk, the color may adhere to the bottom of the stand due to
the composition of the rubber. Check the desk surface before use.
It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more
after the monitor power has been turned on, and then adjust the monitor.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and
maintain a stable display.
When the screen image is changed after displaying the same image for extended periods of time, an
afterimage may appear. Use the screen saver or power save function to avoid displaying the same image for
extended periods of time. Depending on the image, an afterimage may appear even if it was displayed for
a short period of time. To remove such a phenomenon, change the image or keep the power turned off for
several hours.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (For
details, refer to the Instruction Manual.).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may
appear on the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994 % or higher.
The backlight of the LCD panel has a fixed lifetime. When the screen becomes dark or begins to flicker,
please contact your local EIZO representative.
Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions, such
as interference patterns, etc. If pressure is continually applied to the panel, it may deteriorate or damage
your panel. (If the pressure marks remain on the panel, leave the monitor with a black or white screen. The
symptom may disappear.)
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do
not attempt to brush with tissues as this may scratch the panel.
Notice for this monitor
3
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew
condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the
monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage to the
monitor.
Disclaimer
EIZO shall not be liable in any way to any person whatsoever for the occurrences described below.
1. Any incidental, special or consequential disruption or damage directly or indirectly arising in
connection with this product.
2. Any loss, damage or cost resulting from misuse or neglect.
3. Any malfunction or failure occurring after unauthorized disassembly, repair or alteration regardless
of its cause.
4. Any inconvenience, loss or damage caused by the inability to display images due to any reason or
cause including malfunctions or failures in this product.
5. Any failure or consequential inconvenience, loss or damage due to malfunction or failure of a
combined system that comprises this product and any third party products.
6. Any consequential claim for compensation or complaint based on privacy violation or any other
reason by individuals or entities recorded in the surveillance images which are made public for/by
whatever cause or used.
7. Any loss of registered data for whatever cause.
While this product displays camera surveillance images, the use of this product alone does not directly
prevent crime.
Cautions for Network Use
Because this product is used by connecting to networks, the following risks apply
1. Leakage of information through this product.
2. Unauthorized operation of this product by a malicious third party.
3. Interference or suspension of the use of this product by a malicious third party.
In order to prevent the above described damage, it is the user’s responsibility to implement adequate
network security measures including the measures described below.
• Use this product with a safety-ensured network by using a firewall or other network security
systems.
• Change the administrator password periodically.
4
Notice for this monitor
CONTENTS
Notice for this monitor.......................................... 3
Disclaimer.................................................................. 4
Cautions for Network Use........................................ 4
CONTENTS.............................................................. 5
Chapter 1
Product overview............................... 6
1-1.
Features.......................................................... 6
1-2.
System Configuration................................... 7
1-3.
Supported Network Cameras....................... 7
Chapter 2
Configuring from the monitor
screen................................................. 8
2-1.
Before Configuration..................................... 8
2-2.
Setting Screen................................................ 9
2-3.
Setting Network Cameras............................11
●●Basic operations............................................... 9
●●To automatically discover network cameras....11
●●To manually register network cameras...........13
●●To set network camera functions....................15
2-4.
Setting Display Positions of Camera
Images........................................................... 22
2-5.
Setting Smart Functions............................. 23
2-6.
Configuring System Settings..................... 24
2-7.
Setting User Information............................. 34
●●To register new user information.................... 34
●●To change user information........................... 35
●●To delete user information.............................. 35
2-8.
Displaying Operation Logs......................... 36
●●To display log data......................................... 36
●●To save log data..............................................37
Chapter 3
3-5.
Setting Display Positions of Camera
Images........................................................... 48
●●Setting Display Positions............................... 48
●●Other Display Settings................................... 50
●●Setting Smart Functions..................................51
3-6.
Configuring System Settings..................... 52
3-7.
Setting User Information..............................61
3-8.
Displaying Operation Logs......................... 63
3-9.
Setting the Live Image Screen................... 64
●●Date and Time.................................................52
●●Network Settings............................................ 55
●●Communication Settings................................ 56
●●Other System Settings................................... 57
●●Maintenance................................................... 58
●●Adding User Information.................................61
●●Changing User Information............................ 62
●●To delete user information.............................. 62
●●Displaying logs............................................... 63
●●Displaying the system log.............................. 63
●●Live Image Screen Settings........................... 65
●●System Status Settings.................................. 66
Chapter 4
Troubleshooting............................... 67
4-1.
Imaging problems........................................ 67
4-2.
Setting Problems......................................... 68
Chapter 5
5-1.
Reference......................................... 69
List of setting items..................................... 69
Chapter 6
Glossary........................................... 74
Configuring from a Web Browser.... 38
3-1.
Before Configuration................................... 38
3-2.
Web Control Screen..................................... 39
3-3.
Basic Information........................................ 40
●●Basic Operations............................................ 39
●●System Information........................................ 40
●●System Status................................................ 40
●●Camera and Display Position / Date
and TimeSettings / Network Settings /
Communication Settings.................................41
3-4.
Setting Network Cameras........................... 42
●●To automatically detect cameras....................42
●●Load camera information............................... 44
●●Changing Camera Information....................... 45
●●Deleting Camera Information..........................47
●●Save Camera Information...............................47
CONTENTS
5
Chapter 1 Product overview
This color LCD monitor can display images from up to 16 network cameras*1.
This manual describes network camera setup, monitor system setup and specifications, etc.
For information on setup, refer to“Chapter 2 Configuring from the monitor screen” (page 8) and “Chapter
3 Configuring from a Web Browser” (page 38).
*1 A type of camera which converts images into network signals and transmits the signals.
1-1. Features
• 23.0″ wide format LCD
• Supports a resolution of 1920 × 1080
• LCD panel with wide field of view adopted
IPS LCD panel with 178° horizontal and vertical viewing angles
• LED backlight LCD panel
No mercury, a hazardous substance, is used.
• Receives input video signals from network cameras.
-- Compatible with video compression formats H.264 and MJPEG.
-- Up to 16 network cameras can be registered and displayed.
-- Images from multiple network cameras can be displayed simultaneously (1- / 3- / 4- / 8- / 9- /
16-screen display).
-- Network cameras can be controlled from the monitor.
-- Unicast and Multicast video signals can be displayed.
• Equipped with Easy Setup function
Necessary settings for setup can be performed with a wizard.
• Compatible with ONVIF Profile S
• Panasonic and AXIS network cameras can be set using the manufacturer specific protocols.
(When connecting Panasonic or AXIS network cameras)
• Provides display modes (DAY / NIGHT) suitable for surveillance camera images
• EIZO’s unique “Smart” technology
-- Smart Resolution function
This function adjusts the perceived resolution of the images so that the blurs are reduced and images are
displayed vividly and clearly.
-- Smart Insight function
This function analyzes the image and corrects the brightness for each pixel to make dark area of images
visible.
-- Noise Reduction function
This function reduces the amount of block noise that occurs due to video compression.
• Can be operated remotely with the remote control.
• You can register a network camera and configure the live image screen using your web browser
• You can have an alert displayed on the live image screen when communication with a network
camera is lost.
• You can save the settings to a USB storage device and load the settings.
• A 2-year long-term warranty for 24-hour continuous use
6
Chapter 1 Product overview
1-2. System Configuration
Communicating with network cameras, it can display video on the monitor, and operate cameras.
FDF2304W-IP
Ethernet
Network camera*1
HDMI
Network hub
HDMI device*2
(Network video recorder etc.)
*1 Up to 16 network cameras can be registered.
*2 Use an HDMI device (e.g. network video recorder) if necessary.
1-3. Supported Network Cameras
This product supports the following network cameras:
• Panasonic i-pro series network cameras
• AXIS network camera
• ONVIF Profile S-compatible network cameras
Attention
• Supported network cameras vary depending on the monitor’s software version. Check the software version of
the monitor you are using, then check our website (http://www.eizoglobal.com) for details on supported network
cameras. For information on how to check the software version, refer to “2-6. Configuring System Settings” (page
24).
• For installation and settings of network cameras, also check the network camera’s manual.
Chapter 1 Product overview
7
Chapter 2 Configuring from the monitor
screen
You can configure and operate network cameras from the monitor screen. To configure from your web
browser, see “Chapter 3 Configuring from a Web Browser” (page 38). Operating and setting the monitor
can be implemented by using either the Remote Control, or a USB mouse. To use a USB mouse, connect
the mouse to the USB downstream port at the back of the monitor.
2-1. Before Configuration
To configure from the monitor screen, you need to be logged in to the system.
Configuration of this product is allowed only by ADMIN level users.
Be sure to log in to the system with a user account of this level.
Procedure
1. Press
on the front of the monitor or
on the remote control.
The power indicator lights up blue and the live image screen is displayed.
(For information on the live image screen, refer to the Instruction Manual.
2. Select
(Login) under “System”.
The login screen is displayed.
2
5
3
4
3. Enter a username and a password.
4. Select “Login”.
The display changes back to the live image screen.
5. Select
(Setting).
The setting screen is displayed.
(For information on the setting screen, see “2-2. Setting Screen” (page 9).
Note
• See “Entering characters” (page 10) for the character entry method.
• The following user information is set by default:
-- Username: “admin”
-- Password: “admin”
-- User Level: “ADMIN”
• For information on user settings, see “2-7. Setting User Information” (page 34).
• It is recommended that you log out after completing the setup, so as to prevent a third party from operating
the network camera or altering the settings.
Attention
• When the monitor power is turned off while the user is logged in, the user is logged out from the system
automatically. In such a case, you cannot display the web interface in your web browser.
8
Chapter 2 Configuring from the monitor screen
2-2. Setting Screen
The setting screen is used for various settings such as network camera registration and monitor system
settings.
●●Basic operations
List of setting items
The setting screen of the selected item is displayed.
Item
Operation method
To select an item
Press the
To confirm a selected item
Press
To change a setting
With setting buttons:
Press
. (Excluding zoom in / out and position adjustment)
/
/
/
buttons.
.
With list box:
1. Press
.
The list box is highlighted in green.
2. Select the setting with
3. Press
To return to the previous menu level
Press
or
.
.
.
Note
• When canceling a setting change in process, press
To exit the setting screen
1. Select “Exit” from the list of setting items with
2. Press
.
.
.
Attention
• While settings are being applied (registered) to the system, a “Setting” (“Registering”) message is displayed.
Do not turn off the monitor while the message is displayed. Otherwise, setting information may be lost.
Chapter 2 Configuring from the monitor screen
9
Entering characters
1. Press
.
The text field is highlighted in green.
2. Press the number buttons ( 0 to 9 ).
Press a button consecutively to change over to the character next in order. For the order of character entry,
refer to the table shown below.
Button
Input characters
0
0
1
1
2
-
_
:
.
/
(space)
a
b
c
A
B
C
2
3
d
e
f
D
E
F
3
4
g
h
i
G
H
I
4
5
j
k
l
J
K
L
5
6
m
n
o
M
N
O
6
7
p
q
r
s
P
Q
R
8
t
u
v
T
U
V
8
9
w
x
y
z
W
X
Y
To enter a new character, press
To delete a character, press
3. Press
S
7
Z
9
.
.
.
Note
• Entering network addresses
Network address text fields are separated by [.] (a period mark).
-- When a three-digit number is entered, the cursor automatically moves to the next entry position.
-- When entering a two-digit or one-digit number, press to move to the next entry position.
• When using a USB mouse
-- When you enter a period “.”, the cursor moves to the next entry position.
-- To enter characters, click “Keyboard” on the character entry screen. Then click the keys on the displayed
keyboard to enter characters.
Attention
• The remote control cannot be used to select the character entry screen keyboard.
10
Chapter 2 Configuring from the monitor screen
2-3. Setting Network Cameras
●●To automatically discover network cameras
Discover network cameras on the network automatically and register them to the system.
This procedure is for setting network cameras connected after performing “Easy Setup” upon initial
startup of the monitor.
Attention
• Only the network cameras installed in the same subnet as the monitor are detected. If a network camera is
installed in a different subnet, the camera must be registered manually (see “To manually register network
cameras” (page 13)).
• When network cameras are not detected by automatic discovery, see “Chapter 4 Troubleshooting” (page
67).
• For information on “Easy Setup”, refer to the Setup Manual.
Procedure
1. Select “Auto Discovery”.
.
2. Select “Camera Discovery” and press
3. Select the camera type using
or
, then press
.
Displays registered network cameras.
1
4. Select “Start” and press
.
The user authentication screen is displayed.
2
5
3
4
5. Enter the “Username” and “Password” specified in the network camera.
The following values are entered as the default settings. Change the settings if necessary. Please contact
your system administrator for the username and password.
-- Username: “admin”
-- Password: “12345”
Chapter 2 Configuring from the monitor screen
11
6. Select “OK” and press
.
Automatic discovery is started and a “Searching” message is displayed.
When the search is completed, the discovered network cameras are added to the list.
A subsequent result is displayed in the detection results for camera discovery.
Discovery Results
Description
Blank
When there is no information update for the registered network cameras,
or one is not connected
New
Duplicate
When there is an unregistered network camera, or information was
updated for a registered network camera
When there is a network camera with a duplicate IP address
7. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
7
Note
Panasonic network camera
• The settings of the newly detected network camera can be changed.
Select the network camera whose settings you want to change at “Camera Name” and then select
“Settings”. Configure the items on the displayed setting screen. The items that can be set differ depending
on the network camera.
• When registered automatically, stream and channel for accessing the network camera are automatically
set to the following values. You can change the settings in “Manual Setting” (refer to “To manually register
network cameras” (page 13).) Please contact your system administrator for your username and
password to access the network camera.
-- Stream: “2”
-- Channel: “1”
-- RS485 PTZ Control: “Off”*1
*1 Only set “RS485 PTZ Control” to “On” when connecting an external device to the network
camera using a RS485 cable.
AXIS network camera
• When executing automatic detection with an incorrect user name or password, “------” is displayed for the
model name.
• When a detected IP address is a duplicate of a registered network camera, but the username and
password are correct, ‘Model Name – MAC Address’ is displayed, and “------” is displayed for the model
name.
12
Chapter 2 Configuring from the monitor screen
●●To manually register network cameras
Register network cameras manually for cases described below.
• When a network camera is installed in a subnet differing from the subnet of the monitor
• When settings such as network settings of a registered network camera have been changed
• When registering a video encoder which supports multiple channels
Procedure
1. Select “Manual Registration”.
A list of network cameras currently registered is displayed.
3
2
1
Registered cameras are displayed.
2. Select the network camera to configure at “Camera Name”.
When registering a network camera installed in a subnet differing from the subnet of the monitor, select an
available number (with no network camera registered). For a network camera that is already registered,
select the network camera of which to change settings.
3. Select “Settings”.
The network camera setting screen is displayed.
Chapter 2 Configuring from the monitor screen
13
4. Configure the items.
For setting details, contact your system administrator.
4
5
Item
Detail
Setting range
Camera Name
Enter the camera name. When selecting ‘Execute’
for ‘Obtain Camera Name,’ the camera name is
automatically obtained from the network camera.
• Panasonic network camera: Camera Name
• AXIS network camera: Camera Name
• Network camera compatible with the “ONVIF”
protocol: Camera model number, manufacturer
name, etc.
Alphanumeric characters
(up to 24 characters)
IP Address
Enter the network camera IP address.
0.0.0.0 to 255.255.255.255
HTTP Port
Enter the network camera HTTP port number.
1 to 65535
Protocol
Select the protocol for controlling the camera.
Panasonic / AXIS / ONVIF
Stream*1
Set the number of the stream for delivering
camera images. Select a stream supported by the
connected network camera.
CH1 to CH4
Channel*1
Select the channel of the analog encoder. Set to "1" CH1 to CH4
if the network camera does not support the channel
function.
RS485 PTZ Control*1
Controls the brightness, automatic focus adjustment, On / Off
pan, tilt and zoom for devices that are connected to
the network camera via a RS485 cable.
Username, Password
Enter the username and password to use when
accessing network cameras.
Alphanumeric characters and
symbols
(up to 32 characters)
*1 Supported only when compatible with the Panasonic protocol.
5. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
Attention
• If you want to change the set values using the remote control, press the
button, then enter the values
(for details see “Entering characters” (page 10)).
• Depending on the network camera type, the “Model No.” displayed on the setting screen may differ from
when the camera is discovered automatically and when it is registered manually.
• Only set “RS485 PTZ Control” to “On” when connecting an external device to the network camera using a
RS485 cable.
Note
• With manual registration, network settings of a camera cannot be changed. When changing the network
settings of a camera, check the network camera’s manual.
14
Chapter 2 Configuring from the monitor screen
●●To set network camera functions
Set the network camera functions from the monitor.
Procedure
1. Select “Function Settings”.
2
3
Displays current
settings.
1
2. Select the network camera to configure at “Camera Name”.
3. Select a function.
The setting screen for the selected function is displayed.
Camera Information Display
Select to display or not display the camera information and time of the network camera settings on
the camera images.
Attention
• Cannot be set if using a network camera compatible with the “ONVIF” and “AXIS“ protocol.
1
2
1. Configure the items.
Item
Detail
Setting range
Camera Information Display Set whether or not to display camera information. On / Off
Time Display
Set whether or not to display the time.
12h / 24h / Off
Display Position
Set the display position of the camera information Upper Left / Upper Right /
and time.
Lower Left / Lower Right
2. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
Chapter 2 Configuring from the monitor screen
15
Clock Settings
1. Synchronizes the time of the network camera with the time of the monitor.
Select “Execute” to synchronize the clock.
Video Settings
Set the Image Quality of transmitted images for the network camera.
Note
• This product supports H.264 and MJPEG (ONVIF only) video compression formats.
Attention
• When devices such as recorders are connected to a network camera, the display and recording of such
devices may be affected.
16
Chapter 2 Configuring from the monitor screen
When using a Panasonic network camera
1
2
1. Configure the items.
Item
Detail
Setting range
*1
Aspect Ratio
Set the H.264 aspect ratio.
Network camera imaging mode
Resolution
Set the H.264 resolution.
According to the network camera
specification
Refresh Interval
Set the refresh interval*2 of H.264 images.
0.2s / 0.33s / 0.5s / 1s / 2s / 3s / 4s / 5s
Transmission Priority Set the transmission mode of H.264
images.
Constant Bit Rate / Frame Rate / Best
Effort
Frame Rate
(When the mode is set to “Frame Rate” at
“Transmission Priority”.)
Set the frame rate (image update interval)
of H.264 images.*3
1fps / 3fps / 5fps / 7.5fps / 10fps / 12fps /
15fps / 20fps / 30fps
Bit Rate (Max.)
Set the maximum H.264 image bit rate.
64kbps / 128kbps / 256kbps / 384kbps /
512kbps / 768kbps / 1024kbps /
1536kbps / 2048kbps / 3072kbps /
4096kbps / 8192kbps
Bit Rate (Min.)
(When the mode is set to “Best Effort” for
“Transmission Priority”.)
Set the minimum H.264 image bit rate.
64kbps / 128kbps / 256kbps / 384kbps /
512kbps / 768kbps / 1024kbps /
1536kbps / 2048kbps / 3072kbps /
4096kbps / 8192kbps
Image Quality
(When the mode is set to “Constant Bit
Low (prioritize motion) / Normal / Fine
Rate” or “Best Effort” for “Transmission
(prioritize image quality)
Priority”.)
Set the H.264 image quality.
*1 When “1920” is selected for “Resolution”, the aspect ratio is fixed to 16:9. The aspect ratio cannot be
set when the network camera “Stream” is set to a value other than “1”.
*2 For H.264 images, the differential data between the full screen frame data and previous frame are
sent periodically. “Refresh Interval” refers to the interval for sending these full screen frame data.
Shortening this interval improves the stability of image quality but also increases the load on the
network. “Refresh Interval” refers to the interval at which the full screen data is transmitted. Shortening
this interval improves the image quality but also increases the load on the network.
*3 The shorter the interval, the shorter the update interval and the smoother the display, but also the larger
the load on the network.
2. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
Attention
• To display the multicast stream of Panasonic network cameras, configure multicast on the camera.
• When you change the “Aspect Ratio,” the network camera imaging mode will change. Depending on the
imaging mode, the image quality of other recording devices or display devices may be impacted. Check the
impact of changes to the imaging mode before configuring the settings.
Chapter 2 Configuring from the monitor screen
17
When using an AXIS network camera
1
2
1. Configure the items.
Item
Detail
Setting range
Video Stream
Select the display mode for screens that display According to the camera
network camera images.
specification
Stream Profile
Select the profile that the network camera has.
According to the camera
specification
Compression Format
Select the compression format.
H.264 (Fixed)
Resolution
Set the resolution of H.264 images.
According to the camera
specification
Frame Rate
Set the frame rate (image update interval) of
H.264 images.
According to the camera
specification (Maximum possible
values 30fps)
Rotation*1
Show the rotational direction of the network
camera image.
According to the camera
specification
GOP Length
Set the GOP length for video.
I-frame Interval
(only when H.264 is selected)
Bit Rate (Max.)
Set the maximum H.264 image bit rate.
According to the camera
specification (Maximum possible
values 8192 kbps)
Priority
Set the preference for video compression.
none / framerate / quality
Transmission Mode
Select the transmission method for AXIS
camera images.
Unicast / Multicast
Multicast Address*2
Show the multicast address for multicast
transmission of H.264 images.
224.0.0.0 to 239.255.255.255
Multicast Port*2
Show the multicast port number for multicast
transmission of H.264 images.
1024 to 65534 even numbers
only
Multicast TTL*2
Show the network TTL value for multicast
According to the camera
transmission of H.264 images.
specification
*1 For details on rotation settings, refer to the network camera user’s manual.
*2 Displays when “Transmission Mode,” or “Multicast” is selected.
2. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
Attention
• To display the multicast stream of AXIS network cameras, configure multicast on the camera.
18
Chapter 2 Configuring from the monitor screen
ONVIF Profile S-compatible network cameras
1
2
1. Configure the items.
Item
Detail
Setting range
Media Profile
Select the ONVIF image profile.
EIZO_Profile / camera profile
Encoder
Select the encoder settings of ONVIF images. According to the camera
specification
Compression Format Select compression format of ONVIF images. H.264 / MJPEG
Resolution
Set the resolution of ONVIF images.
According to the camera
specification
Frame Rate
Set the frame rate (image update interval) of
ONVIF images.
1 to 30 fps
Encoding Interval
Set the encoder interval of ONVIF images.
According to the camera
specification
Bit Rate (Max.)
Set the maximum ONVIF image bit rate.
0 to 8192 kbps
Video Quality
Set the ONVIF image quality. The higher the
value, the higher the image quality.
According to the camera
specification
GOV Length*1
Set the I-frame interval of ONVIF images.
According to the camera
specification
H.264 Profile*1
Select a H.264 standard profile.
Baseline / Main / Extended / High
Transmission Mode
Select the transmission format of ONVIF
images.
Unicast / Multicast
Multicast Address*2
Set the multicast address for multicast
transmission of ONVIF images.
224.0.0.0 to 239.255.255.255
Multicast Port*2
Set the multicast port number for multicast
transmission of ONVIF images.
1024 to 65534 even numbers only
Multicast TTL*2
Set the network TTL value for multicast
transmission of ONVIF images.
*1 Displays when “H.264” is selected in “Compression Format”.
*2 Displays when “Multicast” is selected in “Transmission Mode”.
According to the camera
specification
2. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
Attention
• Depending on the network camera type, some set values may not be reflected. Check the specifications of
the camera.
• When changes are made to the image quality settings such as resolution, this may impact on the image
quality of other recording devices and display devices using the same ”Encoder”. Check the impact of
changes to the image quality settings before configuring the settings.
Chapter 2 Configuring from the monitor screen
19
Preset
Preset the shooting position and adjustment status of the network camera.
Displays images of the selected network camera.
1
2
3
1. Select the number (1 to 256) to set for “Preset No”.
2. Configure the items.
Item
Detail
Setting range
Brightness
Adjust the network camera brightness.
According to the camera specification
Focus
Adjust the network camera focus.
According to the camera specification
Zoom
Adjust the network camera display
magnification.
According to the camera specification
Position
Adjust the network camera shooting
position (pan / tilt).
According to the camera specification
3. Select “Register (Home)” for registering the selected number as the home position. For all other
registrations, select “Register”.
The setting complete screen is displayed. Select “OK”.
Attention
• Cannot be set if using a network camera compatible with the “AXIS“ protocol. Set the preset settings on the
camera side.
• Depending on the type of the network camera you are using, some functions may not be available.
• Depending on the network camera type, it may not be possible to register the brightness and focus settings.
Note
• After the setting is registered, the number displayed at “Preset No.” changes from “Not Registered” to “Home”
or “Registered”.
• To clear a setting, select the number to clear at “Preset No.” and then select “Delete”. The data set for the
number is deleted and the number status returns to the unregistered state.
20
Chapter 2 Configuring from the monitor screen
Other
Attention
• Cannot be set if using a network camera compatible with the “ONVIF” and “AXIS“ protocol.
1
2
1. Configure the items.
Item
Detail
Setting range
Pan / Tilt-flip
Turn on / off the pan / tilt-flip function*1.
On / Off
Upside-down*2
Turn on / off the network camera upside down
function.
On / Off
Indicator
Turn on / off the network camera Indicator.
On / Off
*1 The pan / tilt-flip function reverses the pan / tilt direction automatically at high-speed when the network
camera reaches the movement endpoint. This function allows the user to make pan / tilt operations
without paying attention to movement endpoints.
*2 Check the network camera installation specifications before using the upside down function.
Depending on the network camera type, it may not be possible to install the camera upside down even
when the camera supports the upside down function.
2. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
Chapter 2 Configuring from the monitor screen
21
2-4. Setting Display Positions of Camera Images
Set the display position for images from the network camera.
Procedure
1. Select “Position”.
2
Indicates the
display positions
on the monitor
screen.
1
3
2. Configure the items.
Item
Detail
Setting range
Position
Select a position to display a camera image.
Set the network camera to the number of the
desired position for display.
-
Camera Name Display
Select to display or not display the camera name
and time set on the monitor. (The camera name is
displayed on the upper left of the image.)
On / Off
Sequence Interval
Set the interval for changing over the screen during 5s to 60s
sequential display.
Aspect Ratio Mode
Set which aspect ratio to apply when the aspect
ratio of the video delivered from the network
camera and the aspect ratio of the monitor image
display area differ.
Full / Aspect
3. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
Attention
• All registered network cameras must be configured. A network camera can only be set for one display position.
When there are incorrect settings, “Apply” cannot be selected.
• When displaying the image layout in three screens
-- Only the Axis network camera displays portrait images maintaining their vertical and horizontal image aspect
ratios. To display images, the network camera setting is required. For details on the settings, refer to the
network camera User’s Manual.
Note
• If it takes a while for images to be displayed during sequential display, set a higher value for “Sequence Interval”.
22
Chapter 2 Configuring from the monitor screen
2-5. Setting Smart Functions
Set Smart Functions for images from each camera.
Procedure
1. Select “Smart Functions”.
Displays images of the selected network camera.
2
Displays current
settings.
1
3
4
2. Select the network camera to configure at “Camera Name”.
Attention
• For 1 Screen or 4 Screens layouts the settings of each network camera are applied. For 3 Screens, 8
Screens, 9 Screens or 16 Screens layouts, the “17_Full Screen” settings are applied to all screens and the
settings of each network camera are not applied.
3. Configure the items.
Item
Detail
Setting range
Mode
Select the display mode to apply to the images of
the selected network camera.
Set to “DAY” to apply a mode suitable for general
images.
Set to “NIGHT” to apply a mode suitable for
monochrome images such as images taken at
night.
DAY / NIGHT / Off
Smart Resolution
Adjusts the perceived resolution of the images
so that the blurs are reduced and images are
displayed vividly and clearly.
1 to 5 / Off
Smart Insight
Makes dark areas of images visible by analyzing
the image and correcting the brightness for each
pixel. It is effective for images with dark area that
are less visible and for bright environments.
1 to 5 / Off
Noise Reduction
Reduces the amount of block noise that occurs due On / Off
to video compression.
4. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
Chapter 2 Configuring from the monitor screen
23
2-6. Configuring System Settings
Set the date, time and network information for this product.
Procedure
1. Select “System”.
2
Displays current
settings.
(e.g. software version)
1
2. Select a setting.
The setting screen for the selected setting is displayed.
Date and Time
Set the current date and time.
1
2
1
2
3
1. Select “Date / Time Display Setting” or “Clock Setting”.
2. Configure the items.
Item
Date / Time Display
Settings
Detail
Setting range
Set the date display format,
Date Format
time display format, and time
zone (time difference between
GMT*1).
Time Format
Time Zone
Clock Setting
Set the current time.
*1 Greenwich Mean Time
24
Chapter 2 Configuring from the monitor screen
yyyy/mm/dd, Mmm/dd/yyyy,
dd/Mmm/yyyy, mm/dd/yyyy,
dd/mm/yyyy
24h / 12h
GMT-12:00 to GMT+14:00
2010/1/1 0:00 to 2035/12/31 23:59
3. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
Attention
• Time zones differ according to the sales region. This needs to be set.
• If the time zone has been changed, daylight saving time will be turned off. (For details, refer to “Summer Time
(DST)” (page 25) in the next section).
Note
• If the main power switch is turned off or the power cord is unplugged for one week or longer, the monitor’s
time and date will no longer be displayed accurately. In such a case, set the date and time again.
Summer Time (DST)
Apply or cancel the summer time setting (DST).
1
2
1. Configure the items.
Item
Summer Time (DST)
Detail
Applies or cancels the summer time setting.
Set to “On” to apply to summer time immediately.
Set to “Off” to not apply to summer time.
Set to “Auto” to apply to summer time automatically
during the period designated by the start / end dates
and times.
Setting range
On / Off / Auto
2. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
Chapter 2 Configuring from the monitor screen
25
Network
Set network information.
1
2
1
2
1
2
3
1. Select “Network Settings”, “DNS Settings” or “NTP Settings”.
2. Configure the items.
Item
Network Settings
DNS Settings
Detail
Setting range
Select the IP address setting method.
IP Setting Method DHCP / Manual
Setting
If “Manual Setting” is selected, set the IP
address, subnet mask and gateway.
IP Address,
Subnet Mask,
Gateway*1
DNS
Set the DNS.
(When “IP Address” of “Network Settings” is set
to “Manual”.)
0.0.0.0 to
255.255.255.255
Auto / Manual
0.0.0.0 to
If you selected “Manual”, set the primary server Primary Server
255.255.255.255
address and the secondary server address.
Address,
Secondary Server
Address
NTP Settings
Set whether or not to use an NTP server.
NTP
If you selected “On”, set the NTP server
address.
Server Address
On / Off
Alphanumeric
characters and
symbols
*1 If your network environment does not include a gateway, you do not need to set the “Gateway”
address. Use the default setting as is, or set as “0.0.0.0”.
3. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
26
Chapter 2 Configuring from the monitor screen
Communication Settings
The communication settings are used to configure the web interface function, detection of
communication errors, and so on.
1
2
1. Configure the items.
Item
Detail
Setting range
Communication speed Sets the communication speed between the monitor
and network hub.
100Mbps Half duplex,
100Mbps Full duplex,
1000Mbps Full duplex
Communication Error
Detection
On / Off
You can set the following as the message to be
displayed when receipt of image data stops.
Comm. Error Detection On:
Within several seconds after receipt of image data
stops, an alert message in a red box will appear
on the live image screen. When communication
resumes, the alert is cleared and the image is
displayed again.
Comm. Error Detection Off:
When approx. 20 seconds have elapsed after receipt
of image data stops, a communication error message
will appear.
Web Interface
You can operate and configure the monitor from your On / Off
web browser over the network.
Web Interface Port
Sets the port of the web interface.
1 to 65535
2. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
Chapter 2 Configuring from the monitor screen
27
Other
1
2
1. Configure the items.
Item
Detail
Setting range
Language
Set the display language of the menu and the setting screen. 日本語 / English /
Deutsch
Quick Start
Set the status of the system when turned off.
When set to “On”, part of the system remains running.
When set to “Off”, the system is shut down completely.
On / Off
By setting to “On”, the startup time for this product can be
reduced (approx. 10 seconds). However, do not turn off the
main power of the monitor when Quick Start is set to “On”
because part of the system remains running.
Key Lock
Locks operations by the buttons on the front of the monitor.
On / Off
Logo
Set whether to display / hide the EIZO logo when the power
is turned on*1.
On / Off
Set whether to turn of or off the power indicator (blue) while
the monitor is on.
*1 The rotating bar indicating that the system is starting up cannot be hidden.
On / Off
Power Indicator
2. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
28
Chapter 2 Configuring from the monitor screen
Initialization
Initialize the system.
1
1. Select “Execute” for “Initialization”.
All settings are returned to default except for system logs, operation logs, the current time, time zone and
summer time settings.
Restart
Restart the system.
1. Select “Execute” at “Restart”.
Settings Data Migration
You can save the settings data to a USB storage device and load the data.
Load Settings Data
2
3
4
5
1. Connect a USB storage device to the USB downstream port of the monitor.
2. Select the settings data file.
3. Enter the password.
The password is blank by default. Set the password as necessary.
4. Select “Execute”. The settings data are loaded.
5. Select “Run” for “Remove USB Storage”.
When the Removing Complete screen is displayed, select “OK”.
6. Remove the USB storage device.
Attention
• The settings data include the IP address of the monitor. Change the IP address of the monitor if loading
settings data from another monitor.
Chapter 2 Configuring from the monitor screen
29
Save Settings Data
1. Connect a USB storage device to the USB downstream port of the monitor.
2
3
4
2. Enter the password.
The password is blank by default. Set the password as necessary.
3. Select “Execute”. The settings data are saved.
4. Select “Run” for “Remove USB Storage”.
When the Removing Complete screen is displayed, select “OK”.
5. Remove the USB storage device.
Attention
• Some of the settings cannot be saved.
• If you forget the password that you specified when saving the data, you will no longer be able to load the settings.
Note
• Saved file name: Backupyyyymmdd.duraconf (yyyymmdd is the save date)
30
Chapter 2 Configuring from the monitor screen
Software Update
You can select update files from the File Selection screen, and can both upgrade or downgrade
software.
1. Download the update file from the EIZO website (http://www.eizoglobal.com), and save it to a USB
storage device.
2. Connect a USB storage device to the USB downstream port of the monitor.
The File Selection screen is displayed.
3
4
3. Select the update file.
4. Select “Execute”.
5. The message saying “You must restart the system to update the software. Remove the USB
storage and restart.” appears. Remove the USB storage device.
6. Select “Restart” to restart the system.
The software is updated.
Attention
• Do not turn off the power while the software is being updated.
• You cannot operate the remote control and
and
buttons on the front of the monitor while the
software is being updated.
• The following USB storage devices can be used with this product (This does not guarantee operation of the
USB storage devices given below).
-- USB 2.0 standard flash drives
-- Supported format: FAT32
• Do not connect multiple USB storage devices simultaneously.
Note
• When you restart your system, a message indicating the success or failure of the software update will appear.
The message will clear automatically after 60 seconds if “OK” is not clicked. However, this message will not
appear if you do the update through your web browser.
Chapter 2 Configuring from the monitor screen
31
Troubleshooting
Use this function when this product does not operate normally, such as when a connection cannot be
established with a network camera or a communication error occurs. The network status can be
checked using communication commands and past error contents can be checked by displaying the
system log. In addition, system log data can be saved to a USB storage device.
Checking network connection status
1
2
3
Displays the
connection check
results.
1. Select “Connection Confirmation”.
2. Select the network camera to check the network connection of for “Camera Name”.
3. Select “Run” for “ping” or “traceroute”.
Results are displayed in the area on the right side of the screen.
Displaying the system log
Displays the log.
1
2
3
1. Select “System Log”.
2. Select the date (year / month / day) to display the log data of.
3. Select “Run” for “Display”.
The log data is displayed in the area on the right side of the screen.
32
Chapter 2 Configuring from the monitor screen
Saving system log data
1. Connect a USB storage device to the USB downstream port on the back of the monitor.
USB downstream port
Displays the data
storage status.
3
2
4
5
2. Select “System Log”.
3. Select the date (year / month / day) of the log data to display.
4. Select “Run” for “Save to USB Storage”.
Data saving starts and a “Saving” message is displayed in the display area on the right side of the screen.
When the saving complete screen is displayed, select “OK”.
5. Select “Run” for “Remove USB Storage”.
When the removing complete screen is displayed, select “OK”.
6. Remove the USB storage device.
Attention
• The following USB storage devices can be used with this product (This does not guarantee operation of the
USB storage devices given below).
-- USB 2.0 standard flash drives
-- Supported format: FAT32
• Do not connect multiple USB storage devices simultaneously.
Chapter 2 Configuring from the monitor screen
33
2-7. Setting User Information
Register, change or delete information (username, user level and password) on users that access this
product.
Attention
• User information can be registered for up to 10 users. User information for a new user cannot be registered when
there are already 10 users registered.
• Duplicate usernames cannot be registered.
• At least one user with a user level of “ADMIN” must be registered.
• You can use alphanumeric characters for the username, however, the following character is not allowed: “ : “.
Note
• There are three user levels: “ LIVE”, “CAMERA CONTROL” and “ADMIN”.
The operable range of this product differs by each level.
(√: Operable, -: Inoperable)
Operation
Menu
display
Level
Layout
change
over
Page
change
over
Smart
Functions
on / off
Login
operation
Camera
control
System
settings
LIVE
√
√
√
√
√
-
-
CAMERA CONTROL
√
√
√
√
√
√
-
ADMIN
√
√
√
√
√
√
√
• The following user information is set by default:
-- Username: “admin”
-- Password: “admin”
-- User Level: “ADMIN”
• User information settings can be returned to default settings by the following procedure. Use this feature, for
example, when you have forgotten the registered user information.
1. Press
on the remote control to turn off the monitor.
2. Press the buttons on the remote control in the following order (press the next button within five seconds).
→
→
→
→
→
→
When the reset confirmation screen is displayed, select “Execute”.
User information is cleared and the settings are returned to the default settings.
●●To register new user information
Procedure
1. Select “User”.
2
3
4
1
2. Select “New User Registration”.
3. Set user information.
4. Select “Register”.
The setting complete screen is displayed. Select “OK”.
34
Chapter 2 Configuring from the monitor screen
●●To change user information
Procedure
1. Select “User”.
2
3
1
4
2. Select “Change / Delete User Information”.
3. Set user information.
4. Select “Change”.
The setting complete screen is displayed. Select “OK”.
●●To delete user information
Procedure
1. Select “User”.
2
3
1
4
2. Select “Change / Delete User Information”.
3. Select the user to delete at “Username”.
4. Select “Delete”.
The setting complete screen is displayed. Select “OK”.
Chapter 2 Configuring from the monitor screen
35
2-8. Displaying Operation Logs
Operations of this product are recorded on logs. Past operation results can be checked by displaying the
log. Also, log data can be saved to a USB storage device.
Note
• The following data are recorded on the log:
-- Login information: The names of users who logged in to the system
-- Camera operation results: Name of operated camera, operation details, operation results
-- Date, time and details of changes confirmed by selecting “Apply” on setting screens
• Logs older than two months are automatically deleted at 04:00:00 AM on the first day of every month.
●●To display log data
Procedure
1. Select “Log Display”.
2
3
1
2. Select the date (year / month / day) to display the log data of.
3. Select “Run” for “Display”.
The log data is displayed in the area on the right side of the screen.
36
Chapter 2 Configuring from the monitor screen
Displays the log.
●●To save log data
Procedure
1. Connect a USB storage device to the USB downstream port on the back of the monitor.
USB downstream port
2. Select “Log Display”.
3
Displays the data
storage status.
4
5
2
3. Select the date (year / month / day) of the data to save.
4. Select “Run” for “Save to USB Storage”.
Data saving starts and a “Saving” message is displayed in the display area on the right side of the screen.
When the saving complete screen is displayed, select “OK”.
5. Select “Run” for “Remove USB Storage”.
When the removing complete screen is displayed, select “OK”.
6. Remove the USB storage device.
Attention
• The following USB storage devices can be used with this product (This does not guarantee operation of the
USB storage devices given below).
-- USB 2.0 standard flash drives
-- Supported format: FAT32
• Do not connect multiple USB storage devices simultaneously.
Chapter 2 Configuring from the monitor screen
37
Chapter 3
Configuring from a Web Browser
This product allows you to configure and operate network cameras from your web browser. Basic
Information, Monitor Settings, and the Live Image Screen Settings are located on the Web control screen.
Note
• To configure from the monitor screen, see ”Chapter 2 Configuring from the monitor screen” (page 8).
Attention
• It is recommended you use Internet Explorer 11 as your web browser.
• If you configure settings from a web browser, you will need to start up the monitor.
• You cannot display the web interface in your web browser when the monitor web interface is disabled in the settings
(For details, see “Communication Settings” (page 56)).
3-1. Before Configuration
To configure settings from a web browser, you need to log in from the web browser you are using. Login
is allowed only when the level of the user accessing the product is ADMIN.
Procedure
1. Press
on the front of the monitor or
on the remote control.
The power indicator lights up blue and the live image screen is displayed.
(For information on the live image screen, refer to the Instruction Manual.)
2. Display the web browser on your PC.
3. Enter the following address to access.
Address: http://Address of the monitors/ui*1
*1 The default address for access is http://192.168.0.150/ui.
The login screen is displayed.
4. Enter a username and a password.
5. Select “Login”.
Displays the Web Control Screen.
Note
• The following user information is set by default:
-- Username: “admin”
-- Password: “admin”
-- User Level: “ADMIN”
• For information on user settings, see “2-7. Setting User Information” (page 34).
• It is recommended that you log out after completing the setup, so as to prevent a third party from operating
the network camera or altering the settings. Exit the web browser.
38
Chapter 3 Configuring from a Web Browser
3-2. Web Control Screen
Basic Information, Monitor Settings, and the Live Image Screen Settings are located on the Web control
screen.
Basic Information display lists of the various settings acquired from the monitor. The Monitor Settings are
used for various settings such as network camera registration and monitor system settings. Live Image
Screen Settings are used for displaying live image screen layout changes and the like.
●●Basic Operations
To select a setting item
• Click a setting item.
When you select a setting item, it will be displayed in green. In the case of a list box, when you
select a list item, it will be displayed in green.
To apply a setting item
• Click “Apply” or “Register”.
A “Setting Complete” or “Setting Failed” message is displayed. Click “OK” as required.
To exit the web browser
• Click
in the web browser. This exits the browser.
Note
• If auto discovery is in progress on the monitor, or the setting dialog box is displayed in the browser, operations
in the web browser will not be accepted. The busy message appears. Click “OK” to configure the settings
again.
Chapter 3 Configuring from a Web Browser
39
3-3. Basic Information
Display lists of the various settings acquired from the monitor.
To make various settings, click to item tab at the top of the screen. This moves you to the setting items
page.
●●System Information
Displays the current status of the monitor system.
• Model Name
•S/N
• Software Version
●●System Status
Shows the monitor screen display status and brightness.
Attention
• If using a monitor firmware version of 2.0002 or earlier, the live image screen brightness is not displayed. A
message “This device does not support the system status settings” is displayed.
40
Chapter 3 Configuring from a Web Browser
and Display Position / Date and TimeSettings / Network
●●Camera
Settings / Communication Settings
Displays the current settings status of the monitor.
To configure settings, click the link for the item name under an item, or click on the setting items tab
at the top of the screen. This moves you to the setting items page.
Chapter 3 Configuring from a Web Browser
41
3-4. Setting Network Cameras
“Camera Registration” is used to display a list of the network cameras currently registered for a monitor.
You can add or change network cameras, and reflect network camera information, etc., onto the monitor.
Attention
• You can only change network cameras that are registered.
• This cannot be used to set network camera functions. For information on setting network camera functions, see
“Chapter 2 Configuring from the monitor screen” (page 8).
●●To automatically detect cameras
Discover network cameras on the network automatically and register them to the system.
Attention
• Only the network cameras installed in the same subnet as the monitor are detected. If a network camera is
installed in a different subnet, the camera must be registered manually (see “To manually register network
cameras” (page 13)).
• For information on “Easy Setup”, refer to the Setup Manual.
Note
• The remaining number of network cameras that can be added for registration is displayed at the top of the
camera detection screen.
Procedure
1. Select “Camera Registration”.
A screen displaying a list of the camera registration information appears.
42
Chapter 3 Configuring from a Web Browser
2. Select “Auto Discovery”.
A “Camera detection will start” dialog box appears.
3. Select the “Protocol” from the list.
Enter the “Username” and “Password” registered in the network camera.
4. Select “OK”.
A “Searching...” dialog box appears, and the detected network cameras are displayed in the list of additional
candidates.
Note
• There is a web page link in the web page field of the list of detected cameras. When you click a link, a
camera web page will open in a separate window. (Address: http://(IP address):(HTTP port))
• If there are zero candidates in camera detection, nothing will display.
• If “Cancel” is selected during camera detection, a list of cameras detected up to the time of canceling will
be displayed.
5. Select a camera to be added from the list of candidates, and select “Add”.
Returns to the camera registration information list screen in step 1.
6. Select “Apply”.
A setting confirmation dialog box appears.
7. Select “OK” or “Cancel” as necessary.
Chapter 3 Configuring from a Web Browser
43
●●Load camera information
Importing a CSV file with the additional candidates for cameras, they can be the candidates for the
network cameras discovery.
Procedure
1. Select “Camera Registration”.
A list of camera registration information appears.
2. Select “Load camera information”.
A file dialog box opens
3. Select the CSV file that describes the network camera information, and select “Open.”
A list of the candidate network cameras appears.
4. Select a camera to be added from the list of candidates, and select “Add”.
Returns to the camera registration information list screen in step 1.
5. Select “Apply”.
A setting confirmation dialog box appears.
6. Select “OK” or “Cancel” as necessary.
44
Chapter 3 Configuring from a Web Browser
Note
• Up to 255 candidate cameras can be read.
• The CSV files that can be read are as follows.
-- CSV files that are exported from the monitor or browser
-- CSV files created by the user
• For details on how to export CSV files, refer to “Save Camera Information” (page 47).
• When a user creates a CSV file, the following rules apply.
-- In line 1, enter the following as the item line: “CameraName, Protocol, IPAddress, HttpPort, UserName,
PassWord”.
-- The columns are in random order.
-- Input of the “UserName, PassWord” values is user-defined.
-- Only the specified string can be read for an item name.
●●Changing Camera Information
You can change the contents of the registered information for cameras in the camera registration
information list.
Attention
• If multiple selections are made for registration information of a network camera to be changed, “Manual
Registration” will be disabled.
1. Select “Camera Registration”.
A screen displaying a list of the camera registration information appears.
2. Check the number of the camera to be changed.
Chapter 3 Configuring from a Web Browser
45
3. Select “Manual Registration”.
A “Camera Information Settings” dialog box appears. When a registered camera is selected, a dialog box
describing the applicable camera information appears.
Item
Detail
Setting range
Camera Name
Can use alphanumeric characters, kana and kanji
0 to 24 characters
IP Address
If a new camera, leave blank
0.0.0.0 to 255.255.255.255
4. Set the changes, and select “OK”.
Returns to the camera registration information list screen in step 1.
5. Select “Apply”.
A setting confirmation dialog box appears.
6. Select “OK” or “Cancel” as necessary.
Note
• The following message is displayed when the system fails to acquire the “Obtain Camera Name” and “Obtain
Profile” information. Obtain the information again.
46
Chapter 3 Configuring from a Web Browser
●●Deleting Camera Information
You can delete the contents of the registered information for cameras.
1. Select “Camera Registration”.
A screen displaying a list of the camera registration information appears.
2. Check the number of the camera to be deleted.
3. Select “Delete”.
A setting confirmation dialog box appears.
4. Select “OK”.
Returns to the screen that displays a list of the camera registration information.
5. Select “Apply”.
A setting confirmation dialog box appears.
6. Select “OK” or “Cancel” as necessary.
●●Save Camera Information
You can save the information registered in the camera registration information list to a CSV file.
When you select “Save Camera Information”, a CSV file describing the camera information displayed
in the information list is exported.
File name: fdf2304wip_CameraInfo_yyyymmdd.csv
(yyyymmdd is the computer date and time.)
Chapter 3 Configuring from a Web Browser
47
3-5. Setting Display Positions of Camera Images
You can configure settings such as the display positions of network cameras, and displaying camera
names in the live image screen.
1. Select “Display” in the “Monitor Settings”.
A screen for display position settings is displayed. A link for each setting item that can be configured in
“Display” is located at the top of the screen.
2. Select each setting item.
The target setting screen is displayed.
●●Setting Display Positions
Set the positions for displaying network camera images.
You can switch the display positions of the source and destination camera images by dragging and
dropping the camera within the page.
Attention
• All of the display positions of registered network cameras can be set.
48
Chapter 3 Configuring from a Web Browser
Procedure
1. Select “Display Position Settings”.
The “Display Position Settings” screen appears.
Each of the outer frames containing the number on the page are the camera display position*1, and the inner
squares for the camera display position are the camera name*2 to be displayed.
*1
*2
2. Select the display position layout from the list.
Select the layout from the list box. The screen changes in response to the selected layout.
Note
• When you select a layout in the list box, the display in the Page changes to the selected state. You can set
the display status while imaging.
• The initial display position when the screen is transitioned is the display position currently set for the
current monitor.
• You can switch the camera names in the inner squares by dragging and dropping them between the
respective pages.
3. Drag a camera name and drop it on the position number where you want to display it.
The display positions of the source and destination camera images are switched.
e.g.) 4 screen layout
1. Drag display position 1 on Page 1 and drop it at display position 5 on page 2.
2. The display position 1 and display position 5 cameras are switched.
3. Only the camera name in the inner square is moved, without moving the display position of the
camera image.
4. Select “Apply”. The display positions of camera images are updated.
When you select “Reset”, the information of the setting being changed is discarded, and becomes the
current monitor display settings.
Note
• A camera web page link is embedded in frames that have been allocated a camera name. When you click
it, a camera web page will open in a separate window.
Chapter 3 Configuring from a Web Browser
49
●●Other Display Settings
Set the items to be displayed in camera images.
Procedure
1. Select “Other Display Settings”.
The “Other Display Settings” screen is displayed.
2. Configure the items.
Item
50
Detail
Setting range
Camera Name Display
Select to display or hide the camera name set on the
monitor. (The camera name is displayed on the upper left
of the image.)
On / Off
Sequence Interval
Set the interval for changing over the screen during
sequential display.
5 to 60 seconds
Aspect Ratio Mode
Set which aspect ratio to apply when the aspect ratio of the Full / Aspect
video delivered from the network camera and the aspect
ratio of the monitor image display area differ.
Chapter 3 Configuring from a Web Browser
●●Setting Smart Functions
Set Smart Functions for images from each camera.
Attention
• Information such as camera name will be displayed as a blank row for display positions that have not been
allocated a camera. Each list box becomes invalid and will not be displayed.
Procedure
1. Select “Smart Functions”.
The “Smart Functions” screen appears.
2. Set the camera of the applicable display position.
3. Configure the items.
Item
Detail
Setting range
Mode
Select the display mode to apply to the images of the
selected network camera.
Set to “DAY” to apply a mode suitable for general images.
Set to “NIGHT” to apply a mode suitable for monochrome
images such as images taken at night.
DAY / NIGHT / Off
Smart Resolution
Adjusts the perceived resolution of images. Reduces
blurring and displays images vividly and clearly.
1 to 5 / Off
Smart Insight
Makes dark areas of images visible by analyzing the image 1 to 5 / Off
and correcting the brightness for each pixel. This function is
effective when for instance viewing images with dark areas
that are not easily visible, or when using the monitor in a
bright environment.
Block Noise Reduction
Reduces the amount of block noise (noise from tessellated
images).
On / Off
4. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
Chapter 3 Configuring from a Web Browser
51
3-6. Configuring System Settings
Configure settings such as the date and time of this product, network settings, and maintenance.
Procedure
1. In the “Monitor Settings”, select “System”.
A link for each setting item that can be configured in the system settings is located at the top of the screen.
2. Select each setting item.
The screen transitions to the selected setting item.
●●Date and Time
You can set the current date and time, and set summer time.
1. Select “Date and Time”.
The “Date and Time” screen is displayed.
52
Chapter 3 Configuring from a Web Browser
Date / Time Display Settings
Set the current date and time.
1. Configure the items.
Item
Date / Time Display
Settings
Detail
Setting range
Set the date display format, time display
format, and time zone (time difference
with GMT*1).
yyyy/mm/dd, Mmm/dd/yyyy,
dd/Mmm/yyyy, mm/dd/yyyy,
dd/mm/yyyy
Time Format
24h / 12h
Time Zone
GMT-12:00 to GMT+14:00
Procedure
Manual / Synchronize with PC
Date and Time
Set the current time.
2010/1/1 0:00 to 2035/12/31
23:59
*1 Greenwich Mean Time
2. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
Note
• When “Synchronize with PC” is selected in “Procedure”, the current date and time setting information of the
computer is sent to the monitor and synchronized.
• If the main power switch is turned off or the power cord is unplugged for one week or longer, the monitor’s
time and date display will no longer be displayed accurately.
Chapter 3 Configuring from a Web Browser
53
Summer Time (DST)
Apply or cancel the summer time setting (DST).
1. Configure the items.
Item
Summer Time (DST)
Detail
Applies or cancels the summer time setting.
Set to “On” to apply summer time immediately.
Set to “Off” to not apply summer time.
Set to “Auto” to apply summer time automatically during
the period designated by the start / end dates and times.
2. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
54
Chapter 3 Configuring from a Web Browser
Setting range
On / Off / Auto
●●Network Settings
Set network information.
Attention
• When any one of the IP address settings / IP address / subnet mask / gateway is changed and “Apply” is
selected, the warning message “The network settings will be changed” is displayed. Select “OK” or “Cancel”
as necessary.
Also, when you select “OK” for the warning message, a message requesting that you access again appears.
1. In “System”, select “Network Settings”.
The “Network Settings” screen is displayed.
2. Configure the items.
Item
Network Settings
DNS Settings
NTP Settings
Detail
Setting range
Select the IP address setting method.
IP Setting Method
If “Manual Setting” is selected, set the IP
address, subnet mask and gateway.
IP Address, Subnet 0.0.0.0 to
Mask, Gateway*1
255.255.255.255
DNS
Set the DNS.
(When “IP Address” in “Network Settings”
is set to “Manual”)
DHCP / Manual
Setting
Auto / Manual
If you selected “Manual”, set the primary
server address and the secondary server
address.
Primary Server
Address,
Secondary Server
Address
0.0.0.0 to
255.255.255.255
Set whether or not to use an NTP server.
NTP
On / Off
If you selected “On”, set the NTP server
address.
Server Address
Alphanumeric,
symbols
*1 If your network environment does not include a gateway, you do not need to set the “Gateway”. Use
the default setting as is, or set as “0.0.0.0”.
3. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
Chapter 3 Configuring from a Web Browser
55
●●Communication Settings
The communication settings are used to configure the web interface function, detection of
communication errors, and so on.
1. In “System”, select “Communication Settings”.
The “Communication Settings” screen is displayed.
2. Configure the items.
Item
Communication
Speed
Detail
Set the communication speed between the monitor and
network hub.
Communication Error You can set the following as the message to be displayed
Detection
when receipt of image data stops.
Setting range
100Mbps Half duplex,
100Mbps Full duplex,
1000Mbps Full duplex
On / Off
Communication Error Detection On:
Within several seconds after receipt of image data stops,
an alert message in a red box will appear on the live image
screen. When communication resumes, the alert is cleared
and the image is displayed again.
Communication Error Detection Off:
When approx. 20 seconds have elapsed after receipt of
image data stops, a communication error message will
appear.
Web Interface
You can operate and configure the monitor from your web
browser over the network.
Web Interface Port
Sets the port of the web interface*1
*1 When the web interface is enabled, you can set the port.
On / Off
1 to 65535
3. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
Attention
• When the web interface is disabled, you will not be able to configure the monitor settings from your web
browser. When the web interface is disabled and “Apply” is selected, the following warning message
appears.
56
Chapter 3 Configuring from a Web Browser
●●Other System Settings
1. In “System”, select “Other System Settings”.
The “Other System Settings” screen appears.
2. Configure the items.
Item
Detail
Setting range
Language
Set the display language of the menu and the setting
screen.
日本語 / English / Deutsch
Quick Start
Set the status of the system when turned off.
When set to “On”, part of the system remains running.
When set to “Off”, the system is shut down completely.
On / Off
By setting to “On”, the startup time for this product can
be reduced (approx. 10 seconds). However, do not turn
off the main power of the monitor when Quick Start is
set to “On” because part of the system remains running.
Key Lock
Locks operations by the buttons on the front of the
monitor.
On / Off
Logo
Set whether to display / hide the EIZO logo when the
power is turned on*1.
On / Off
Power Indicator
Set whether to turn of or off the power indicator (blue)
On / Off
while the monitor is on.
*1 The rotating bar indicating that the system is starting up cannot be hidden.
3. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
Chapter 3 Configuring from a Web Browser
57
●●Maintenance
Perform system initialization, restarts, and software updates.
1. In “System”, select “Maintenance”.
The “Maintenance” screen is displayed.
Initialization and Restart
Initialize the system
1. Select “Execute” for “Initialization”.
All settings are returned to default setting except for system logs, operation logs, the current time, time
zone and summer time settings.
2. The following message appears.
Select “OK” or “Cancel” in accordance with the response.
58
Chapter 3 Configuring from a Web Browser
Restart the system
1. Select “Start” at “Restart”.
Restart the system.
2. The following message appears.
Select “OK” or “Cancel” in accordance with the response.
Chapter 3 Configuring from a Web Browser
59
Software Update
You can both upgrade or downgrade the software version.
1. In “System”, select “Maintenance”.
The screen transitions to “Software Update”.
2. Select “Browse”.
A file selection dialog box opens. Select the applicable file.
Attention
• The software will not be updated if a file is not selected, or a file other than an update file has been
selected.
• Perform software updates with the monitor screen displayed.
3. Select “Execute”.
4. The following message appears.
Select “OK” or “Cancel” in accordance with the response.
5. Select “OK”.
The update process starts, and the following message appears.
6. The software is updated.
Close the web browser, and wait 5 minutes before accessing again.
Note
• You can select update files from the File Selection screen, and can perform upgrading or downgrading of
software.
• When you restart your system, a message indicating the success or failure of the software update will
appear. The message will clear automatically after 60 seconds if “OK” is not selected. However, this
message will not appear if you do the update through your web browser.
60
Chapter 3 Configuring from a Web Browser
3-7. Setting User Information
Register, change or delete information (username, user level and password) on users that access this
product.
Note
• For details, see “2-7. Setting User Information” (page 34).
●●Adding User Information
Procedure
1. Select “User”.
The “User Settings” screen is displayed.
2. Select “Add”.
A dialog box for entering user information appears.
3. Set user information.
4. Select “OK”.
The setting complete screen is displayed. Select “OK”.
Chapter 3 Configuring from a Web Browser
61
●●Changing User Information
Procedure
1. Select “User”.
2. Select the user to be changed from the “User List”.
3. Select “Change”.
A dialog box for entering user information appears.
4. Set user information.
5. Select “OK”.
The setting complete screen is displayed. Select “OK”.
●●To delete user information
Procedure
1. Select “User”.
2. Select the user to be deleted from the “User List”.
3. Select “Delete”.
4. A “Are you sure you want to delete user xxx?” confirmation dialog box appears. Select “OK”.
If you do not want to delete the user, select “Cancel”.
5. The setting complete screen is displayed. Select “OK”.
62
Chapter 3 Configuring from a Web Browser
3-8. Displaying Operation Logs
Operations of this product are recorded on logs. Past operation results can be checked by displaying
operation logs. You can also display system logs.
Note
• The following data are recorded on the log:
-- Login information: The names of users who logged in to the system
-- Camera operation results: Name of operated camera, operation details, operation results
-- Date, time and details of changes confirmed by selecting “Apply” on setting screens
• Logs older than two months are automatically deleted at 04:00:00 AM on the first day of every month.
●●Displaying logs
Procedure
1. Select “Log Display”.
2. Select “Operation Log Display”.
The log data is displayed in the area at the bottom of the screen.
●●Displaying the system log
Procedure
1. Select “Log Display”.
2. Select “System Log Display”.
The log data is displayed in the area at the bottom of the screen.
Chapter 3 Configuring from a Web Browser
63
3-9. Setting the Live Image Screen
The live image screen settings are used for changing the live image screen layout, or the present monitor
status.
Procedure
1. In “Live Image Screen”, select “Live Image Screen Settings”.
A link for each setting item that can be configured in the live screen settings is located at the top of the
screen.
2. Select each setting item.
The target setting screen is displayed.
64
Chapter 3 Configuring from a Web Browser
●●Live Image Screen Settings
The live image screen settings are used for configuring the display, such as changing the live image
screen layout.
1. Select each setting item from the list box.
Item
Detail
Setting range
Full Screen Display
Displays / hides the menu of the live image screen.
On / Off
Layout
Changes the monitor screen layout.
You can switch to 1 screen, 3 screen, 4 screen, 9 screen,
16 screen, or 8 screen layout.
1 Screen / 3 Screens
4 Screens / 9 Screens /
16 Screens / 8 Screens
Page
Changes over the page of camera images to display on the 1 to 16
monitor.
Sequence
Turns the sequential display of camera images on or off.
On / Off
Smart Functions
Turns the Smart function on or off.
On / Off
2. Select “Apply”.
3. The setting completion screen appears. Select “OK”.
Chapter 3 Configuring from a Web Browser
65
●●System Status Settings
Sets the current monitor screen display status and brightness.
Current Status
Adjusts the current monitor screen display status.
1. Click ▼ next to “Current Status” to select the status from the displayed list.
The following statuses are displayed.
Item
Status
Live Image Screen
Monitor showing live screen
Setting Screen
Monitor showing setting screen
HDMI Port Display
Display status of the monitor HDMI port.
Quick Shutdown
Quick-start is on, and the power is off.
2. Select “Refresh Status”.
Applies the latest status on the monitor.
Attention
• When Quick Shutdown is selected:
A setting error occurs and a “Quick Start is set to OFF. Run after setting Quick Start to ON.” message is
displayed.
Brightness
Adjusts the brightness of the monitor screen.
1. Move the camera “Brightness” slider to the left and right.
Changes the brightness of the monitor screen.
2. “Select “Refresh Status”.
Applies the latest status on the monitor.
Note
• You can change the Brightness on the monitor screen in the same manner as when pressing the
(
,
) buttons on the remote control. A “Setting Complete” or “Setting Failed” message is
not displayed after changing the brightness.
• If using a monitor FW version of 1.0002 or earlier, adjust the brightness setting using the and buttons.
66
Chapter 3 Configuring from a Web Browser
Chapter 4 Troubleshooting
4-1. Imaging problems
Problem
Possible cause and remedy
1. The displayed images are not smooth
(when camera images are being displayed)
• Reduce the resolution and / or bit rate set for the network
camera (see “Video Settings” (page 16)).
• Check whether the used hubs and network cables are
appropriate for handling the amount of information
transmitted.
2. The camera images are not displayed
correctly for about one or two minutes
after the monitor power is turned on (when
camera images are being displayed)
• When the main power is turned off and immediately back
on, images may not be displayed properly for the first few
minutes. However, the display will normalize after a few
minutes.
3. The time of the network camera and the
time of the monitor do not match (when
camera images are being displayed)
• Synchronize the time of the camera and the monitor
through the setting screen (see “Clock Settings” (page
16)).
4. Images are displayed upside down (when
camera images are being displayed)
• Turn the network camera upside down through the setting
screen (see “Other” (page 21)).
5. When the orientation of the network
camera is changed to the horizontal
direction (pan motion), the camera moves
in the opposite direction
• Turn the network camera upside down through the setting
screen (see “Other” (page 21)).
6. The settings set on the setting screen are
not reflected on the camera images
• Check whether the setting details are within the setting
range of the network camera.
7. An error message “E**-**” is displayed at
the camera image display area
• When “E00-00” is displayed
--Check whether a network cable is connected properly.
--Check whether the network camera is turned on.
• When “E00-01” is displayed
--A number of devices exceeding the allowable number of
devices for simultaneous connection may be connected
to the network camera. Disconnect other network
devices accessing the camera or reduce the resolution
of the camera (see “Video Settings” (page 16)).
--The network camera may not be transmitting H.264
images. Check the settings of the camera.
• When “E00-02” is displayed
--Network bandwidth may be overwhelmed or the display
capability of this product may have been exceeded.
Reduce the resolution and / or bit rate set for the
network camera (see “Video Settings” (page 16)).
• When a system error (E00-03) is displayed
--Restart the system.
8. A “** Camera Control Error” message is
displayed at the message display area
• The network camera may not be equipped with the
function operated. Check the specifications of the camera.
9. The screen is whitish or blackish (for HDMI
input)
• Change the “Color Space” setting (For details, refer to the
Setup Manual.).
Chapter 4 Troubleshooting
67
4-2. Setting Problems
Problem
68
Possible cause and remedy
1. Network camera is not detected automatically
• In some cases, automatic discovery and camera IP
address setting become inoperable when 20 or more
minutes have passed since the network camera was
started up. Restart the camera or register manually (see
“To manually register network cameras” (page 13)).
• Network cameras installed in subnets other than the
monitor subnet cannot be discovered automatically.
Register the camera manually. Auto discovery and camera
operation may fail when the date and time of the network
camera and monitor are not aligned. Use the software
provided with the camera to adjust the date and time.
• If using a network camera that is compatible with the
“ONVIF” protocol, auto discovery cannot be performed if
the ONVIF function is disabled on the camera. Check the
settings of the camera.
2. An IP address of an automatically
discovered network camera cannot be
changed
• In some cases, automatic discovery and camera IP
address setting become inoperable when 20 or more
minutes have passed since the network camera was
started up. Restart the camera or register manually (see
“To manually register network cameras” (page 13)).
• If using anything other than a Panasonic network camera,
network settings cannot be changed from this monitor.
3. Only one camera is recognized when using
a video encoder that supports multiple
channels
• Manually register the number of channels that will be
used. (see “To manually register network cameras” (page
13)).
4. A communication error message is
displayed when “Apply” is selected for
network camera manual registration
• There may be a problem with network camera
communication. Check the network connection status and
camera registration details.
5. Network camera does not respond to pan /
tilt / zoom operations
• The network camera may not support pan / tilt / zoom
functions. Check the specifications of the camera.
6. Cannot register a new user
• Duplicate usernames cannot be registered.
• Only up to 10 users can be registered. Check whether 10
users have already been registered (see “2-7. Setting User
Information” (page 34)).
7. Cannot delete a user
• There must be at least one user with a level of “ADMIN”.
A user cannot be deleted if the user is the only one
registered with a level of “ADMIN”. Check the registered
user information (see “2-7. Setting User Information” (page
34)).
8. Forgot username and password
• The information of usernames and passwords can be
returned to default settings by pressing a combination
of buttons on the remote control (see “2-7. Setting User
Information” (page 34)).
9. Cannot communicate with the camera
• Check the settings of the network camera and the monitor
system. For details, contact your system administrator.
10. Cannot save log data to a USB storage
device
• This product supports only FAT32 format.
11. The date and time are not displayed
correctly
• If the main power switch is turned off or the power cord is
unplugged for one week or longer, the monitor’s date and
time display will become inaccurate. In such a case, set
the date and time again (see “2-6. Configuring System
Settings” (page 24)).
Chapter 4 Troubleshooting
Chapter 5 Reference
5-1. List of setting items
Note
• The setting items and values differ according to the camera.
Easy
Setup*1
Easy Setup
Setting item
Date and Time
Network
Settings
Setting
Date/Time
Date Format yyyy/mm/dd
Display Settings
Mmm/dd/yyyy
dd/Mmm/yyyy
mm/dd/yyyy
dd/mm/yyyy
Time
24h
Format
12h
Time Zone GMT-12:00
GMT-11:00
GMT-10:00
GMT-09:30
GMT-09:00
GMT-08:00
GMT-07:00
GMT-06:00
GMT-05:00
GMT-04:30
GMT-04:00
GMT-03:30
GMT-03:00
GMT-02:00
GMT-01:00
GMT
GMT+01:00
GMT+02:00
GMT+03:00
GMT+03:30
GMT+04:00
GMT+04:30
GMT+05:00
GMT+05:30
GMT+05:45
GMT+06:00
GMT+06:30
GMT+07:00
GMT+08:00
GMT+08:45
GMT+09:00
GMT+09:30
GMT+10:00
GMT+11:00
GMT+11:30
GMT+12:00
GMT+12:45
GMT+13:00
GMT+14:00
Date and Time Year
2010 to 2035
Settings
Month
1 to 12
Day
1 to 31
1 to 30
1 to 28
1 to 29
Hour
AM/PM
(24h) 0 to 23
(12h) 1 to 12
Minute
0 to 59
IP Setting Method
DHCP
Manual Setting
IP Address
0.0.0.0 to 255.255.255.255
Subnet Mask
0.0.0.0 to 255.255.255.255
Gateway
0.0.0.0 to 255.255.255.255
Camera Discovery
Panasonic/AXIS/ONVIF
Camera Auto
Discovery
Display Position Settings
Default setting
yyyy/mm/dd
24h
(Depends on sales region)
Manual Setting
192.168.0.150
255.255.255.0
192.168.0.1
(None)
Chapter 5 Reference
69
Camera
Setting item
Auto
Camera Discovery
Discovery
Manual
Camera Name
Registration
IP Address
HTTP Port
Protocol
Channel
Stream
RS485 PTZ Control
Username
Camera Info.
Display/Clock
Settings
Video Settings
(When using
a Panasonic
network
camera)
(None)
Camera Information Display
Alphanumeric characters
(0 to 24 characters)
0.0.0.0 to 255.255.255.255
1 to 65535
Panasonic/AXIS/ONVIF
1 to 4
1 to 4
On/Off
Alphanumeric characters and
symbols (0 to 32 characters)
Alphanumeric characters and
symbols (0 to 32 characters)
On/Off
Time Display
12h/24h/Off
Display Position
Upper Left/Upper Right/
Lower Left/Lower Right
Synchronize with Monitor Time
Aspect Ratio
Camera imaging mode
Resolution
Refresh Interval
Transmission Priority
Frame Rate
Bit Rate (Max.)
Bit Rate (Min.)
Image Quality
Video Settings
(When using a
AXIS network
camera)
Video Stream
Stream Profile
Compression Format
Resolution
Frame Rate
Rotation
GOP Length
Bit Rate (Max.)
70
Chapter 5 Reference
Default setting
(None)
Password
Function
Settings*1
Setting
Panasonic/AXIS/ONVIF
According to the camera
specification
0.2s/0.33s/0.5s/1s/2s/
3s/4s/5s
Constant Bit Rate/Frame
Rate/Best Effort
1fps/3fps/5fps/7.5fps/
10fps/12fps/15fps/
20fps/30fps
64kbps/128kbps/
256kbps/384kbps/
512kbps/768kbps/
1024kbps/1536kbps/
2048kbps/3072kbps/
4096kbps/8192kbps/
64kbps/128kbps/
256kbps/384kbps/
512kbps/768kbps/
1024kbps/1536kbps/
2048kbps/3072kbps/
4096kbps/8192kbps/
Low (prioritize motion)/
Normal/Fine (prioritize image
quality)
According to the camera
specification
According to the camera
specification
H.264 (Fixed)
According to the camera
specification
According to the camera
specification (Maximum
possible values 30fps)
According to the camera
specification
(None)
(None)
(None)
(None)
(None)
Off
admin
12345
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
I-frame Interval
(According to the camera
(only when H.264 is selected) specification)
According to the camera
(According to the camera
specification (Maximum
specification)
possible values 8192 kbps)
Camera
Function
Settings*1
Setting item
Video Settings
(When using a
AXIS network
camera)
Video Settings
(ONVIF Profile
S-compatible
network
cameras)
none/framerate/quality
Transmission Mode
Unicast/Multicast
Multicast Address
Multicast Port
224.0.0.0 to
239.255.255.255
1024 to 65535
Multicast TTL
1 or higher
Media Profile
EIZO_Profile/
camera profile
According to the camera
specification
H.264/MJPEG
Encoder
Compression Format
Resolution
Video Quality
Frame Rate
Encoding Interval
Bit Rate (Max.)
GOV Length
Display
Position
Smart
Functions
System
System
According to the camera
specification
0 to 8192
Multicast Port
Multicast TTL
1 or higher
Preset No.
Brightness
Focus
Zoom
Pan/Tilt
Pan/Tilt-flip
1 to 256
Upside-down
On/Off
Indicator
On/Off
Transmission Mode
Multicast Address
Other
According to the camera
specification
According to the camera
specification
1 to 30
According to the camera
specification
Baseline/Main/Extended/
High
Unicast/Multicast
224.0.0.0 to
239.255.255.255
1024 to 65535
H.264 Profile
Preset
Setting
Priority
Position
Camera Name Display
Sequence Interval
Aspect Ratio Mode
On/Off
1 to 16
On/Off
5s to 60s
Full
Aspect
Mode
DAY/NIGHT/Off
Smart Resolution
1 to 5/Off
Smart Insight
1 to 5/Off
Noise Reduction
On/Off
Date and Time Date/Time
Date Format yyyy/mm/dd
Display Settings
Mmm/dd/yyyy
dd/Mmm/yyyy
mm/dd/yyyy
dd/mm/yyyy
Time
24h
Format
12h
Default setting
(According to the camera
specification)
Unicast
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
Unicast
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(None)
(According to the camera
specification)
(According to the camera
specification)
(According to the camera
specification)
(Current setting)
Off
5s
Full
DAY
3
3
On
yyyy/mm/dd
24h
Chapter 5 Reference
71
System
System
Setting item
Date and Time
Date/Time
Time Zone
Display Settings
Clock Setting
Year
Month
Day
Hour
Minute
Summer Time
(DST)
Network
Summer Time
(DST)
Network
Settings
DNS Settings
NTP Settings
72
Chapter 5 Reference
Start
End
IP Setting
Method
IP Address
Subnet
Mask
Gateway
DNS
Primary
Server
Address
Secondary
Server
Address
NTP
Server
Address
Setting
Default setting
GMT-12:00
GMT-11:00
GMT-10:00
GMT-09:30
GMT-09:00
GMT-08:00
GMT-07:00
GMT-06:00
GMT-05:00
GMT-04:30
GMT-04:00
GMT-03:30
GMT-03:00
GMT-02:00
GMT-01:00
GMT
GMT+01:00
GMT+02:00
GMT+03:00
GMT+03:30
GMT+04:00
GMT+04:30
GMT+05:00
GMT+05:30
GMT+05:45
GMT+06:00
GMT+06:30
GMT+07:00
GMT+08:00
GMT+08:45
GMT+09:00
GMT+09:30
GMT+10:00
GMT+11:00
GMT+11:30
GMT+12:00
GMT+12:45
GMT+13:00
GMT+14:00
2010 to 2035
1 to 12
1 to 31
1 to 30
1 to 28
1 to 29
AM/PM
(24h) 0 to 23
(12h) 1 to 12
0 to 59
On/Off/Auto
(Depends on sales region)
Month, Week, Day, Hour
Month, Week, Day, Hour
DHCP/Manual Setting
(None)
(None)
Manual Setting
0.0.0.0 to 255.255.255.255
0.0.0.0 to 255.255.255.255
192.168.0.150
255.255.255.0
0.0.0.0 to 255.255.255.255
Auto/Manual
0.0.0.0 to 255.255.255.255
192.168.0.1
Manual
(None)
0.0.0.0 to 255.255.255.255
(None)
Off
On/Off
Off
Alphanumeric characters and (None)
symbols
System
System
Setting item
Communication Communication Speed
Settings
Communication Error
Detection
Web Interface
Web Interface Port
Other
Settings Data
Migration
Language
Quick Start
Key Lock
Logo
Power Indicator
Save Settings Data*1
Load Settings Data*1
Setting
100Mbps Half duplex,
100Mbps Full duplex,
1000Mbps Full duplex
On/Off
On/Off
1 to 65535
日本語 /English/Deutsch
On/Off
On/Off
On/Off
On/Off
Default setting
(current setting)
Off
On
80
(Depends on sales region)
Off
Off
On
On
Initialization
Software Update
Restart
Troubleshooting Connection
Confirmation
Camera Name
ping
traceroute
System Log
Date (GMT)
Display
Save to USB Storage*1
Remove USB Storage*1
*2
User
New User
Username
Alphanumeric characters
Registration
(1 to 16 characters)
User Level
ADMIN/CAMERA
CONTROL/LIVE
Password
Alphanumeric characters
(1 to 16 characters)
Confirm Password
Alphanumeric characters
(1 to 16 characters)
Change/Delete Username
(Registered user)
User Information New Username
Alphanumeric characters
(1 to 16 characters)
New User Level
ADMIN/CAMERA
CONTROL/LIVE
New Password
Alphanumeric characters
(0 to 16 characters)
Confirm New Password
Alphanumeric characters
(0 to 16 characters)
Log Display Date (GMT)
Display
Save to USB Storage*1
Remove USB Storage*1
(None)
(None)
(None)
(None)
(None)
(None)
(None)
(None)
(None)
*1 This can only be set from the monitor screen. This is not available through your web browser.
*2 The following user information is set as the default setting:
Username: “admin”, Password: “admin”, User Level: “ADMIN”
Chapter 5 Reference
73
Chapter 6 Glossary
Bit Rate
Displays the volume of data flowing across the network. Generally, the volume is expressed with
the unit “bps” (bits per second) which indicates the number of data bits transmitted per second.
DNS (Domain Name Server)
A server used to convert addresses such as “www.eizoglobal.com” into IP addresses.
Firewall
A system to prevent invasion from external networks.
H.264
A format for compressing images. This method is widely used for image remote transmission and
recording. The portion with movement is predicted based on the data of the frame immediately
before and after, and only the differential data between frames is used. This enables efficient
reduction of data, and is therefore widely used.
IP Address
An address that is allocated to a network device. Each network device is given an address. Unlike
MAC addresses, IP addresses change according to the installation environment.
MAC (Media Access Control) Address
A Mac address is a 48bit identification number assigned to a network device. It is assigned
statically, not duplicated, and uses a unique number for each network device.
Multicast
A network communication format in which multiple network devices receive a single stream. By
having multiple network devices receive the same image at the same quality, the network load of
transmitting devices can be reduced, however, it is necessary to have devices and configurations
that support multicast.
MJPEG (Motion JPEG)
This is a method for compressing images. It is used for remote transmission and recording of
images. Due to compression and decompression being performed for each frame, subsequent
frames are not impacted even when data are missing from some frames. Therefore, this method is
sometimes used in environments with poor signal quality. However, a downside is that the data
volume is larger than that for the H.264 format.
NTP (Network Time Protocol)
A protocol for synchronizing the time and the network server.
ONVIF (Open Network Video Interface Forum)
This is a standard that allows interconnection between network cameras and network recorder
equipment from different manufacturers.
74
Chapter 6 Glossary
ping
A command used to check the connection status with other network devices. Generally, it is judged
that there is a problem in the network route when there is no response to ping requests, and the
ping command is used for finding out the cause of the problem.
PoE (Power over Ethernet)
A technology to supply electricity using an Ethernet cable.
Port
A communication contact number for network communication. When multiple services are provided
by one network device, allotting an individual port number for each service allows the device to
provide multiple services simultaneously.
Resolution
The LCD panel consists of numerous pixels of specified size, which are illuminated to form images.
This monitor consists of 1920 horizontal pixels and 1080 vertical pixels. At a resolution of 1920 ×
1080, all pixels are illuminated as a full screen (1:1).
Subnet Musk
A subnet mask is a numeric value where the network address part identifying the subnet can be
specified in an IP address.
(Subnet: a divided network when controlling a large network by dividing into multiple networks)
TCP/IP (Transmission Control Protocol/Internet Protocol)
The TCP/IP is one of the network protocols for network communication. Using the TCP/IP protocols
allows communication in various OSes.
traceroute
A command used to check the routes used to connect with other network devices.
Unicast
A network communication format in which individual network devices perform one-to-one
communication. Whereas an image quality that is suitable for each individual network device can
be transmitted, the downside to this format is that transmitting devices place a high load on the
network.
Chapter 6 Glossary
75
2nd Edition-August, 2016
Copyright © 2016 EIZO Corporation. All rights reserved.
03V25780B1
(IM-FDF2304WIP)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising