Eizo | FDF2304W-IP | Owner Manual | Eizo FDF2304W-IP Owner Manual

Eizo FDF2304W-IP Owner Manual
Instruction Manual
Color LCD Monitor
Software Version 4.3
Thank you for purchasing our Color LCD Monitor.
Important
Please read this “Instruction Manual”, the “Installation Manual” and
the “Setup Manual” carefully to familiarize yourself with safe and
effective usage.
• For the latest product information including the “Instruction Manual”,
refer to our web site:
http://www.eizoglobal.com
About this manual
Setup Manual
Describes precautions and setup processes from network camera
connection to camera image display.
Instruction Manual
(this manual)
Describes operation of network cameras and live image screen
menus, etc.
Installation Manual
Describes network camera registration and function setup, monitor
system setup, etc.
This product has been adjusted specifically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specifications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information confidential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specifications are subject to change without notice.
2

Notice for this monitor
Cleaning
The stains on the cabinet and LCD panel surface can be removed by moistening part of a soft cloth with water.
Attention
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet
or LCD panel, and also quality deterioration of the image.
• Never use thinner, benzine, wax, or abrasive cleaner as they may damage the cabinet or LCD panel surface.
Note
• It is recommended that ScreenCleaner (available as an option) be used to clean the cabinet and LCD panel surface.
To use the monitor comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor
according to the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
Notice for this monitor
3
CONTENTS
Notice for this monitor.......................................... 3
Cleaning..................................................................... 3
To use the monitor comfortably.............................. 3
CONTENTS.............................................................. 4
Chapter 1
1-1.
Product overview............................... 5
System Configuration................................... 5
Chapter 2
●●
●●
Turning On / Off the Power............... 6
To turn on the power........................................ 6
To turn off the power........................................ 6
Chapter 3
Operating the System....................... 7
3-1.
Remote Control.............................................. 7
3-2.
Live Image Screen......................................... 8
3-3.
Changing Over Screen Layout and
Displayed Pages...........................................12
●●Basic menu operations.................................... 9
●●To change over the screen layout...................12
●●To change over the page displayed on
the screen.......................................................13
●●To switch camera image display positions......14
3-4.
Turning Visibility Optimizer Function
On / Off...........................................................15
3-5.
Controlling Network Cameras.....................15
3-6.
Adjusting Screen Brightness......................19
3-7.
To switch among input signals...................19
●●Before operation..............................................15
●●To Operate network cameras..........................17
Chapter 4
4
Troubleshooting............................... 20
4-1.
No picture..................................................... 20
4-2.
Imaging problems........................................ 20
4-3.
Other problems.............................................21
CONTENTS
Chapter 1 Product overview
This color LCD monitor can display images from up to 16 network cameras*1.
*1 A type of camera which converts images into network signals and transmits the signals.
1-1. System Configuration
FDF2304W-IP
Ethernet
*1
Network camera
HDMI
Network hub
HDMI device*2
(Network video recorder etc.)
*1 Up to 16 network cameras can be registered.
*2 Use an HDMI device (e.g. network video recorder) if necessary.
Chapter 1 Product overview
5
Chapter 2 Turning On / Off the Power
●●To turn on the power
1. Turn on the main power switch on the back of the monitor.
The main power switch is turned on when factory default settings are configured.
2. Press
on the front of the monitor or
on the remote control.
The power indicator lights up blue and the live image screen is displayed.
(For details on the live image screen, refer to “3-2. Live Image Screen” (page 8).)
Attention
• By default, it takes approximately one minute for the live image screen to be displayed after the power is turned
on (A rotating bar indicating startup is displayed). Do not turn off the monitor during startup.
• When the monitor is started up for the first time, a menu for operating the monitor and network cameras is
displayed.
• When no network camera is registered, a “Not Registered” message is displayed at the network camera image
display area.
Note
• The time required to display the live image screen can be reduced (Quick Start) by changing the power-off status.
For details, refer to the Installation Manual.
●●To turn off the power
1. Press
on the front of the monitor or
on the remote control.
Attention
• The power indicator flashes blue while the system is shutting down.
• The power-off status differs depending on the “Quick Start” setting. For details, refer to the Installation Manual.
-- When set to “On”: Part of the system remains running. (Power Indicator: Red)
-- When set to “Off”: The system is shut down completely (default setting). (Power Indicator: OFF)
• When turning off the main power of the monitor, follow the procedure below.
1. If “Quick Start” is set to “On”, change the setting to “Off”.
2. Press
on the front of the monitor or
on the remote control to turn off the power.
The system is shut down and the power indicator turns off.
3. Turn off the main power switch.
• Turning off the main power of the monitor before the system completely shuts down may cause equipment
damage.
• Use the remote control within the range illustrated in the diagram below.
5m
5m
30°
7m
7m
30°
20°
20°
5m
5m
• When installing multip le monitors, leave sufficient space between each monitor so that only the intended monitor
will be operated by the remote control. Otherwise, all monitors that receive the remote control signal will operate
accordingly.
6
Chapter 2 Turning On / Off the Power
Chapter 3 Operating the System
Each menu is operated using the remote control or a USB mouse.
This chapter describes operating the menus using the remote control. To operate menus when using a USB
mouse, refer to each item. For details on connecting a USB mouse, refer to “Basic menu operations” (page
9).
3-1. Remote Control
1
2
3
4
5
6
7
9
8
10
11
12
13
Name
Description
1.
Switches input signals for display.
2.
Turns the power on or off.
3.
Used to display / exit the monitor’s Adjustment menu.
4.
/
Adjusts the brightness of the monitor screen.
5. Number Buttons
( 0 to 9 ) /
Used to enter numbers and letters.
6.
Adjusts the network camera display magnification.
7.
/
/
/
/
Used to set and control (pan / tilt) network cameras, and configure system
settings of the monitor.
,
8.
Returns to the previous menu status in menu operation.
9.
Changes the live image screen layout.
Each time the button is pressed, the layout changes in the following order:
1 Screen → 3 Screens → 4 Screens → 9 Screens → 16 Screens → 8 Screens →
Custom Screen → 1 Screen.
10.
Displays / hides the menu of the live image screen.
*1
11.
12.
13.
Turns Visibility Optimizer function on or off.
Turns the sequential display of camera images on or off.
/
Changes the camera image page to display on the live image screen.
*1 Some remote controls are labeled “Smart”.
Chapter 3 Operating the System
7
3-2. Live Image Screen
The live image screen is displayed when the monitor is turned on.
There are two states to the live image screen. Live image screen menu can be shown or hidden by
pressing
.
Live image screen
(camera images and menu)
Live image screen
(camera images only)
Note
• You can also operate the live image screen from your Web browser. For information on operation from a Web
browser, refer to the Installation Manual.
8
Chapter 3 Operating the System
●●Basic menu operations
The menu is used for operation and setting of network cameras and the monitor.
Live Image Screen
Display mode menu
Current time
System setup menu / Camera control menu
Message display area
(Error messages such as on camera operations are displayed.)
Network camera image display area
• When no camera is registered, a “Not registered ” message is displayed.
• When an input signal is not supported, the “Unsupport resolution” message is displayed.
Attention
• When sequence display is enabled, the system setup menu and the camera control menu are inoperable.
Note
• The displayed menus can be operated by remote control even if the menus on the live image screen are
hidden.
• When using a USB mouse to operate the menu
-- Connect the mouse to the USB downstream port at the back of the monitor.
Chapter 3 Operating the System
9
Display mode menu
Camera images displayed on the live screen can be operated.
Display mode menu
Remote control
button
Description
Displays / hides the menu of the live image display screen.
Changes the live image screen layout.
Each time the button is pressed, the layout changes in the
following order:
1 Screen → 3 Screens → 4 Screens → 9 Screens →
16 Screens → 8 Screens → Custom Screen → 1 Screen.
*1
Turns Visibility Optimizer function on or off.
Turns the sequence display of the camera image (mode
that switches the display page at regular intervals) on or
off.
Changes the camera image page to display on the live
image screen.
/
*1 Some remote controls are labeled “Smart”.
System setup menu / Camera control menu
The system settings menu is used for logging into and configuring the system.
The camera control menu controls network cameras from the monitor in the camera operation menu.
Item
Operation method
To select an item
Press the
/
/
/
buttons.
To confirm a selected item
Press
To change a setting
With setting buttons:
. (Excluding zoom in / out and position adjustment)
Press
.
With list box:
1. Press
.
The list box is highlighted in green.
2. Select the setting with
3. Press
To return to the previous menu level
Press
Note
or
.
.
.
• When canceling a setting change in process, press
10
Chapter 3 Operating the System
.
Entering characters
1. Press
.
The text field is highlighted in green.
2. Press the number buttons ( 0 to 9 ).
Press a button consecutively to change over to the character next in order. For the order of character entry,
refer to the table shown below.
Button
Input characters
0
0
1
1
2
-
_
:
.
/
(space)
a
b
c
A
B
C
2
3
d
e
f
D
E
F
3
4
g
h
i
G
H
I
4
5
j
k
l
J
K
L
5
6
m
n
o
M
N
O
6
7
p
q
r
s
P
Q
R
8
t
u
v
T
U
V
8
9
w
x
y
z
W
X
Y
To enter a new character, press
To delete a character, press
3. Press
S
7
Z
9
.
.
.
Note
• Entering network addresses
Network address text fields are separated by [.] (a period mark).
-- When a three-digit number is entered, the cursor automatically moves to the next entry position.
-- When entering a two-digit or one-digit number, press to move to the next entry position.
• When using a USB mouse
-- When you enter a period “.“, the cursor moves to the next entry position.
-- To enter characters, click “Keyboard” on the character entry screen. Then click the keys on the displayed
keyboard to enter characters.
Attention
• The remote control cannot be used to select the character entry screen keyboard.
• The operable range of the menu differs according to the level of the user accessing this product.
There are three user levels: “LIVE”, “CAMERA CONTROL” and “ADMIN”. The range of operation for each
level is shown below.
(√: Operable, -: Inoperable)
Switching camera
Operation
System
setup
menu
Display
Camera control
image display
Level
mode menu Login operation
menu
System settings
positions
LIVE
√
√
CAMERA
CONTROL
√
√
-
√
-
ADMIN
√
√
√
√
√
• When the power is turned on and after logoff, the user level is “LIVE”.
• For information on setting user levels, refer to the Installation Manual.
Chapter 3 Operating the System
11
3-3. Changing Over Screen Layout and Displayed Pages
●●To change over the screen layout
Changes the number of camera images to display on the live image screen.
Procedure
1. Press
on the remote control.
Each time the button is pressed, the screen layout changes over. When using a USB mouse, the screen
layout changes by selecting the display screen layout icon.
1 Screen
3 Screens
4 Screens
9 Screens
Custom Screen
8 Screens
16 Screens
Attention
When displaying the image layout in three screens:
• Suitable for portrait input images. To display portrait images, network cameras require separate settings. For
details on the settings, refer to the network camera User’s Manual.
Note
• The selected network camera image is displayed in one screen by selecting the live image screen network
camera image and pressing
on the remote control.
12
Chapter 3 Operating the System
●●To change over the page displayed on the screen
Except for when the screen layout is 16 Screens, camera images are displayed by changing over
pages.
Pages can be changed over either manually or automatically at a set interval (sequential display).
Note
• When “Custom Screen” is specified for the screen layout, the number of pages varies depending on the
specified number of screens.
Changing pages manually
Procedure
1. Press
or
on the remote control.
Each time the button is pressed, the page displayed on the screen changes over. When using a USB mouse,
select
or
in the display menu.
Example: 4 Screens layout
Camera 1
Camera 2
Camera 5
Camera 6
Camera 3
Camera 4
Camera 7
Camera 8
Camera 13
Camera 14
Camera 9
Camera 10
Camera 15
Camera 16
Camera 11
Camera 12
Changing pages automatically (Sequential display)
Procedure
1. Press
on the remote control.
Pages displayed on the screen are changed over automatically at a specified interval.
Note
• The interval for page changeover can be changed (default setting: 5 sec). For information on how to change
the display interval, refer to the Installation Manual.
• To stop sequential display, press
again.
Attention
• During sequential display, camera control is disabled and the setting screen cannot be displayed. The
sequential display must be stopped in order to operate cameras or display the setting screen. For information
on how to display the setting screen, refer to the Installation Manual.
• Only pages registered for the network camera are displayed in the sequence display. Pages not registered
with the camera will not be displayed.
Chapter 3 Operating the System
13
●●To switch camera image display positions
If the image layout is displayed in multiple screens other than one screen, camera image display
positions can be switched.
Drag and drop the camera image on the live image screen, and the display positions of the source
and destination camera image are switched.
Attention
• It is necessary to log in as a user with a user level of “ADMIN”.
• It is possible to switch all the display positions of the registered network cameras.
Procedure
1. Using a USB mouse, drag the camera image and drop it on a position where you want to display
it.
The display positions of the source and destination camera image are switched.
14
Chapter 3 Operating the System
3-4. Turning Visibility Optimizer Function On / Off
Enable or disable settings of Visibility Optimizer function. Using the Visibility Optimizer function improves
the camera image visibility.
Procedure
*1
1. Press
on the remote control. (*1 Some remote controls are labeled “Smart”.)
Each time the button is pressed, Visibility Optimizer function is turned on or off.
Note
• For information on how to configure the Visibility Optimizer function, refer to the Installation Manual.
3-5. Controlling Network Cameras
●●Before operation
Network camera control is allowed only when the level of the user accessing this product is
“CAMERA CONTROL” or “ADMIN”.
Be sure to log in to the system with a user account of either of these levels.
Procedure
1. Select
(Login) under “System”.
The login screen is displayed.
1
2
3
2. Enter a username and a password.
3. Select “Login”.
The display returns to the live image screen.
Chapter 3 Operating the System
15
4. Press
on the remote control.
The system frame is selected (highlighted in green).
Note
• For information on how to enter characters, refer to “Entering characters” (page 11).
• The following user information is set by default:
-- Username: “admin”
-- Password: “admin”
-- User Level: “ADMIN”
• For information on how to configure users, refer to the Installation Manual.
• It is recommended that you log out after completing operations, so as to prevent a third party from operating
the camera or altering the settings.
• When the Auto Login settings are configured, you can log in to the system without entering the username and
password. For details, refer to the Installation Manual.
Attention
• Once the Auto Login settings are configured, unauthorized operation becomes easy for a malicious third
party. Restrict the configuration to the application in an environment where sufficient security is ensured.
• When the monitor power is turned off while the user is logged in, the user is logged out from the system
automatically. In such a case, you will also be logged out from the web browser.
16
Chapter 3 Operating the System
●●To Operate network cameras
Procedure
1. Select the camera control menu.
1. Press
.
2. Select the camera control menu using
.
or
, then press
2. Select the network camera to operate.
1. Check that “Camera” is selected and press
.
2. Select a network camera displayed in the live image screen
. The frame around the
using or , then press
selected camera image become bold.
.
3. Press
3. Select a function to use.
1. Select a function to use using
2. Press
or
.
.
4. Operate the functions.
Attention
• Depending on the type of the network camera you are using, some functions may not be available.
• There is a setting that makes the network cameras completely inoperable. For details, refer to the Installation
Manual.
Note
• To select a network camera to operate, use the numerical buttons on the remote control. Also, click the USB
mouse to select an the image in the live image screen.
• The position at which images in the live image screen are displayed can be changed. For details, refer to the
Installation Manual.
Chapter 3 Operating the System
17
Brightness / Preset / Focus
Function
Brightness
Preset
Detail
Adjusts the brightness of the network camera.
1. Select the setting button and press
.
:
Each time
:
Returns the brightness to the default setting.*1
:
Each time
is pressed, the image becomes darker.
is pressed, the image becomes brighter.
Moves the camera orientation to the position registered in advance.
1. Select the “Preset” list box and press
.
2. Select the preset number with
or
and press
.
Note
• For information on registering a preset position, refer to the Installation Manual.
• To move the network camera orientation to the home position, select
.
Focus
Adjusts the network camera focus.
1. Select the setting button and press
.
is pressed, the focus point moves closer.*2
:
Each time
:
Focuses automatically.*3
:
Each time
is pressed, the focus point moves farther away.*2
*1 Cannot be set if using a network camera for which “Protocol” is “ONVIF” or “AXIS.”
*2 If using a network camera for which “Protocol” is “ONVIF” or “AXIS,” the mode is switched to manual
adjustment mode.
*3 If using a network camera for which “Protocol” is “ONVIF” or “AXIS,” the mode is switched to automatic
adjustment mode.
Zoom / Position
Function
Zoom
Position
Detail
Adjusts the network camera display magnification.
1. Press
/
.
:
Zooms out each time
is pressed.
:
Zooms in each time
is pressed.
Adjusts the shooting position of the network camera.
1. Press / /
/ .
:
Adjusts the horizontal position (pan).
:
Adjusts the vertical position (tilt).
Auxiliary Command
Function
Auxiliary
Command
Detail
Operates auxiliary functions for the network camera(s).
1. Select the list box for the “Auxiliary Commands”, then press
2. Select the auxiliary command using
or , then press
.*1
.
*1 Auxiliary commands can be operated using only specified devices for which the protocol is “ONVIF” or
“Panasonic”.
Note
• When operating with a USB mouse, the network camera position can be adjusted automatically by clicking on
a position in the image where you wish to set as the center of the image display (only supports Panasonic or
AXIS network cameras equipped with pan, tilt, and zoom functions).
18
Chapter 3 Operating the System
3-6. Adjusting Screen Brightness
Adjust the brightness of the monitor screen by changing the brightness of the backlight (light source at
the back of the LCD panel).
Adjustable range
0 to 100
Procedure
1. Press
or
on the remote control.
The brightness adjustment menu is displayed.
2. Set the brightness with
or
.
The menu disappears automatically after approximately five seconds.
3-7. To switch among input signals
Press
on the remote control to change over the input signal.
When the signal is switched, the active input port name appears at the top right corner of the screen.
Note
•
on the monitor also can change the input.
Chapter 3 Operating the System
19
Chapter 4 Troubleshooting
4-1. No picture
Problem
1. No picture
• Power indicator does not light.
Possible cause and remedy
• Check whether the power cord is connected properly.
• Turn the main power switch on.
on the
• Press on the front of the monitor or
remote control.
• Turn off the main power, and then turn it on again a few
minutes later.
• Power indicator is lighting blue.
• Adjust the screen brightness (For details, refer to the
Setup Manual).
• Power indicator is lighting blue. (for HDMI
input)
• Check whether the HDMI cable is connected properly.
• Check whether the connected device is turned on.
• Pull out the HDMI cable and connect it again (For details,
refer to the Setup Manual).
4-2. Imaging problems
Problem
20
Possible cause and remedy
1. The screen is too bright or too dark
• Adjust the screen brightness (For details, refer to the
Setup Manual). (The LCD monitor backlight has a limited
life span. When the screen becomes dark or begins to
flicker, contact your local EIZO representative.)
2. Afterimages appear
• Afterimages are particular to LCD monitors. Avoid
displaying the same image for a long time.
3. Green / red / blue / white dots or defective
dots remain on the screen
• This is due to LCD panel characteristics and is not a
failure.
4. Interference patterns or Pressure marks
remain on the LCD panel
• Switch to the HDMI port and try displaying a white or black
image on full screen. The symptom may disappear.
Chapter 4 Troubleshooting
4-3. Other problems
Problem
Possible cause and remedy
1. Operation buttons on the front of the
monitor do not work
• Check whether the operation lock function is active
(For information on how to release the lock, refer to the
Installation Manual).
2. Buttons on the remote control do not work
• Check whether the remote control is pointed to the signal
receiving part.
• Check for obstacles between the remote control and the
signal receiving part.
• Batteries are dead.
• Check whether batteries are inserted correctly.
3. The mouse does not work
• Check whether the USB cable is connected properly.
• Pull out the USB cable and connect it again.
• Check whether the mouse is directly connected to the
monitor.
4. Remote control or mouse responses lag
• Reduce the resolution and / or bit rate set for the network
camera (For details, refer to the Installation Manual).
5. Network camera cannot be operated
• The system is not logged in by a user with a camera
operable level (For details, refer to the Installation
Manual).
• Network camera is inoperable during sequential display
(For details, refer to the Installation Manual).
• Refer to the Installation Manual and check the setup of the
network cameras.
6. USB flash drive is not recognized
• Check whether the USB flash drive is connected properly.
• Take out the USB flash drive and insert it again.
• Check whether the USB flash drive is directly connected
to the monitor.
Chapter 4 Troubleshooting
21
03V25779D1
UM-FDF2304WIP-3
Copyright © 2016-2018 EIZO Corporation. All rights reserved.
4th Edition-February, 2018
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising