Eizo | EV2430 | User manual | Eizo EV2430 User Manual

Eizo EV2430 User Manual
User’s Manual
Color LCD Monitor
Important
Please read this “User’s Manual”, and “PRECAUTIONS” (separate
volume) carefully to familiarize yourself with safe and effective usage.
••Refer to the “Setup Guide” for information on the installation /
connection of the monitor.
••For the latest product information including the “User’s Manual”,
refer to our web site :
http://www.eizoglobal.com
Location of Caution Statement
This product has been adjusted specifically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specifications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information confidential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specifications are subject to change without notice.
2

Notice for this monitor
This product is suited to general purposes like creating documents, viewing multimedia content (Assuming
usage of approximately 12 hours per day).
If using this product for the following kinds of applications, where an extremely high degree of reliability and
safety is required, then measures should be in place to maintain safety while using this product.
•• Transportation equipment (ships, aircraft, trains, and automobiles)
•• Safety devices (Disaster prevention systems, security control systems, etc.)
•• Life-critical devices (medical devices, such as life-support devices and operating room devices)
•• Nuclear energy control devices (Nuclear energy control systems, security control systems of nuclear facilities, etc.)
•• Major system communication devices (operation control systems of transportation systems, air traffic control systems, etc.)
This product has been adjusted specifically for use in the region to which it was originally shipped. If the
product is used outside the region, it may not operate as specified in the specifications.
This product may not be covered by warranty for uses other than those described in this manual.
The specifications noted in this manual are only applicable when the following are used:
•• Power cords provided with the product
•• Signal cables specified by us
Only use optional products manufactured or specified by us with this product.
If you place this product on a lacquer-coated desk, the color may adhere to the bottom of the stand due to
the composition of the rubber. Check the desk surface before use.
It takes about 30 minutes (under our measurement conditions) for the monitor display to stabilize. Please
wait 30 minutes or more after the monitor power has been turned on, and then adjust the monitor.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and
maintain a stable display.
When the screen image is changed after displaying the same image for extended periods of time, an
afterimage may appear. Use the screen saver or power save function to avoid displaying the same image for
extended periods of time. Depending on the image, an afterimage may appear even if it was displayed for
a short period of time. To remove such a phenomenon, change the image or keep the power turned off for
several hours.
If the monitor displays continuously over a long period of time, dark smudges or burn-in may appear. To
maximize the life of the monitor, we recommend the monitor be turned off periodically.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer
to “Cleaning” (page 4)).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may
appear on the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994 % or higher.
The backlight of the LCD panel has a fixed lifetime. Depending on the usage pattern, such as usage for
long continuous periods, the lifespan of the backlight may run out sooner, requiring replacement. When the
screen becomes dark or begins to flicker, please contact your local EIZO representative.
Do not press on the LCD panel or edge of the frame strongly, as this may result in display malfunctions, such
as interference patterns, etc. If pressure is continuously applied to the LCD panel surface, the liquid crystal
may deteriorate or the LCD panel may be damaged. (If the pressure marks remain on the panel, leave the
monitor with a black or white screen. The symptom may disappear.)
Do not scratch or press on the LCD panel with any sharp objects, at this may result in damage to the LCD
panel. Do not attempt to brush with tissues as this may scratch the panel.
Notice for this monitor
3
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew
condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the
monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage to the
monitor.
Cleaning
The stains on the cabinet and LCD panel surface can be removed by moistening part of a soft cloth with water.
Attention
•• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet
or LCD panel, and also quality deterioration of the image.
•• Never use thinner, benzine, wax, or abrasive cleaner as they may damage the cabinet or LCD panel surface.
Note
•• It is recommended that ScreenCleaner (available as an option) be used to clean the cabinet and LCD panel surface.
To use the monitor comfortably
•• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor
according to the environmental conditions.
•• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
4
Notice for this monitor
CONTENTS
Notice for this monitor.......................................... 3
Chapter 3
Setting Monitor................................ 23
Cleaning..................................................................... 4
3-1.
Adjusting Volume........................................ 23
To use the monitor comfortably.............................. 4
3-2.
Selecting sound source while using the
DisplayPort signal input............................. 23
3-3.
Enabling / Disabling DDC/CI
communication ........................................... 23
3-4.
Locking Operation Buttons........................ 24
3-5.
Setting Orientation...................................... 24
3-6.
Showing and hiding the EIZO logo............ 24
3-7.
Changing Setting Menu Display
Position......................................................... 25
3-8.
Setting Language......................................... 25
3-9.
Resetting the Monitor to the Default
Settings......................................................... 26
CONTENTS.............................................................. 5
Chapter 1
Introduction........................................ 7
1-1.
Features.......................................................... 7
1-2.
Controls and Functions................................ 8
●●Front................................................................. 8
●●Rear.................................................................. 9
1-3.
Basic Operations and Functions................10
●●Basic operation of the Setting menu...............10
●●Functions.........................................................11
Chapter 2
2-1.
Adjusting Screens........................... 12
Compatible Resolutions..............................12
●●
●●Digital Input (DVI-D)........................................12
●●Digital Input (DisplayPort)...............................12
Analog Input (D-Sub)......................................12
2-2.
Setting the Resolution.................................13
●●To reset the color adjustments....................... 26
●●To reset “EcoView Sense Settings”............... 26
●●To reset all adjustments to the default
settings........................................................... 26
●●Windows 10.....................................................13
●●Windows 8.1 / Windows 7...............................13
●●OS X Mountain Lion (10.8) or later..................13
●●Mac OS X 10.7................................................13
Chapter 4
●●To select the display mode (color mode)........14
●●To perform advanced adjustments.................14
●●Adjustable settings in each mode...................15
●●To adjust brightness........................................15
●●To adjust contrast............................................16
●●To adjust color temperature............................16
●●To adjust gamma . ..........................................17
●●To adjust the color saturation..........................17
●●To adjust hue...................................................18
●●To adjust gain..................................................18
2-3.
Adjusting Color.............................................14
Power Saving Functions................. 27
4-1.
Setting Power Saving.................................. 27
4-2.
Setting Power Indicator............................... 28
4-3.
Enabling / Disabling Automatic
Brightness Adjustment .............................. 28
●●Monitor........................................................... 27
●●Audio Output.................................................. 28
●●Auto EcoView................................................. 28
●●EcoView Optimizer 2...................................... 29
4-4.
Setting the power saving mode when a
person leaves the monitor.......................... 29
4-5.
Checking the power saving level................31
4-6.
Enabling / Disabling Auto Power-OFF........31
Chapter 5
Troubleshooting............................... 32
5-1.
No picture..................................................... 32
●●Digital Signal Input..........................................19
●●Analog Signal Input.........................................19
5-2.
Imaging problems (for both digital and
analog)........................................................... 33
5-3.
Imaging problems (for digital only)........... 34
●●Screen Size Changing................................... 22
●●To adjust brightness of non-display area....... 22
5-4.
Imaging problems (for analog only).......... 34
5-5.
Other problems............................................ 35
2-4.
Screen Adjustment.......................................19
2-5.
Screen Size Changing................................. 22
CONTENTS
5
Chapter 6
Reference......................................... 36
6-1.
Attaching the Optional Arm........................ 36
6-2.
Detaching/Attaching Stand Base................37
6-3.
Attaching/Detaching Cable Holder............ 40
6-4.
Connecting Multiple PCs............................ 42
●●To switch among input signals........................42
●●To set input signal selection........................... 43
6-5.
Using the USB Hub Function...................... 43
●●
Connection Procedure (Setup of USB
Function)......................................................... 44
6-6.
6-7.
Displaying Monitor Information................. 44
Specifications.............................................. 45
●●
Accessories.................................................... 46
Appendix............................................................... 47
Trademark.................................................................47
License......................................................................47
ENERGY STAR..........................................................47
FCC Declaration of Conformity............................. 48
6
CONTENTS
Chapter 1 Introduction
Thank you very much for choosing an EIZO color LCD monitor.
1-1. Features
• 24.1″ wide format LCD
• Supports a resolution of 1920 × 1200
• Applicable to DisplayPort (applicable to 8 bit)*1
The DisplayPort input receives both an image signal and an audio signal via a single DisplayPort cable.
*1 When transmitting an audio signal using the DtisplayPort cable, the graphics board must be compatible with audio
output (see “6-7. Specifications” (page 45)).
• The Color Mode function allows the user to select the display mode optimum to the displayed image.
-- The Paper mode reproduces a printed paper effect on the monitor. In Paper mode, the amount of blue light
emitted from the screen is reduced by changing the color tone and controlling the brightness.
See “To select the display mode (color mode)” (page 14).
• Power saving function
Suppressing the power consumption*2 reduces the carbon dioxide emissions. This product is equipped with power saving
function.
-- 0 W power consumption when the main power is off
Equipped with main power switch.
When the monitor is not required, the power supply can be shut off using the main power switch.
-- Auto EcoView
The ambient light sensor on the front side of the monitor detects the environmental brightness to adjust the screen
brightness automatically and comfortably.
See “Auto EcoView” (page 28).
-- EcoView Optimizer 2
The monitor automatically adjusts the screen brightness according to the white level of the input signal. This
function can reduce the power consumption while maintaining the brightness specified by the input signal.
See “EcoView Optimizer 2” (page 29).
-- EcoView Sense
The sensor on the front side of the monitor detects the movement of a person. When a person moves away from the
monitor, the monitor shifts to the power saving mode automatically and does not display the images on the screen.
Therefore, the function reduces the power consumption. The sensitivity and time until the power saving mode is
activated can be set according to the monitor usage environment and movement of the user.
See “4-4. Setting the power saving mode when a person leaves the monitor” (page 29).
*2 Reference values:
Maximum power consumption: 36 W (Brightness Max., when a USB device is connected, speaker working, at
default settings)
Standard power consumption: 12 W (Brightness 120 cd/m 2, when no USB device is connected, speaker not working,
at default settings)
• Supports portrait and landscape formats
• Displays HDCP (High-bandwidth Digital Protection) protected contents.
Note
• This monitor supports the portrait display. This function allows you to change the orientation of the Setting menu when
using the monitor screen in vertical display position (see “3-5. Setting Orientation” (page 24)).
• When using the monitor screen in a portrait position, the graphics board supporting portrait display is required. When
placing the monitor in a portrait position, the settings of your graphics board need to be changed. Refer to the User’s
Manual of the graphics board for details.
Chapter 1 Introduction
7
1-2. Controls and Functions
●●Front
Setting menu*1
1
2
3
4
5
6
7
8
9
1. EcoView Sense sensor
Detects the movement of a person in front of the monitor (EcoView Sense function (page
29)).
2. Ambient light sensor
Detects ambient brightness (Auto EcoView function (page 28)).
3.
Displays the setting menu of the power saving function (Auto EcoView (page 28) and
EcoView Optimizer 2 (page 29)) and EcoView Sense (page 29).
button
button
4.
Switches input signals for display (page 42).
5.
button
Switches the color mode (page 14).
6.
button
Displays the Setting menu, determines an item on the menu screen, and saves values
adjusted (page 10).
7.
,
8.
button
button*2
• Provides the menu selection as well as the adjustment and setting of a function.
•
button: Displays the volume adjustment menu (page 23).
button: Displays the Brightness adjustment menu (page 15).
Turns the power on or off.
Indicates the monitor’s operation status.
9. Power indicator
White:
Operating
Orange:
Power saving mode
OFF:
Main power / Power off
*1 See “1-3. Basic Operations and Functions” (page 10) for how to use.
*2 In this User’s Manual, the
button may be hereafter simply displayed as
8
Chapter 1 Introduction
, and the
button as
.
●●Rear
20
10
11
12
15
13
16
17
18
19
21 *3
21 *3
14
10. Main power switch
Turns the main power on ( ) or off (
11. Power connector
Connects the power cord.
12. Input signal connector
Left: DisplayPort connector / Center: DVI-D connector / Right: D-Sub mini15-pin
connector
13. Security lock slot
Complies with Kensington’s MicroSaver security system.
14. Speaker
Outputs audio.
).
Handle used for transportation
15. Handle
Attention
• Firmly grasp and hold the monitor by the bottom while grabbing the handle, and carefully
convey the monitor so as not to drop it.
16. USB downstream port Connects a peripheral USB device.
17. USB upstream port
Connects the USB cable for using the USB Hub function (page 43).
18. Headphone jack
Connects the headphones.
19. Analog audio input
connector
Outputs external audio from the monitor.
20. Stand*4
Adjusts the height and angle (tilt and swivel) of the monitor.
21. Cable holder
Covers the monitor cables.
*3 See “6-3. Attaching/Detaching Cable Holder” (page 40) for how to attach the cable holder.
*4 An optional arm (or an optional stand) can be attached by removing the stand (see “6-1. Attaching the Optional Arm” (page 36)).
Chapter 1 Introduction
9
1-3. Basic Operations and Functions
●●Basic operation of the Setting menu
1. Displaying the Setting menu
1. Press
. The Setting menu appears.
2. Adjusting / Setting
1. Choose a menu to adjust / set with , , and then press
. The Sub menu appears.
2. Choose an item to adjust / set with , , and then press
. The adjustment / setting menu appears.
3. Adjust / set the selected item with , , and then press
3. Exiting
1. Choose “Return” from the Sub menu and press
2. Choose “Exit” from the Main menu and press
.
. The Setting menu appears.
. The Setting menu quits.
Note
• The Setting menu can also be exited by pressing
10
Chapter 1 Introduction
twice quickly.
●●Functions
The following table shows the Setting menu and setting items of each menu.
Main menu
Color*1
Screen
Sound
Setting
Brightness
Contrast
Temperature
Gamma
Advanced Settings
Reference
“2-3. Adjusting Color” (page 14)
Saturation
Hue
Gain
Color Reset
Screen Size
Smoothing
Analog Adjustment*2 Auto Screen Adjust
Auto Range Adjust
Clock
Phase
Hor.Position
Ver.Position
Source
“To reset the color adjustments” (page 26)
“Screen Size Changing” (page 22)
“2-4. Screen Adjustment” (page 19)
“3-2. Selecting sound source while using
the DisplayPort signal input” (page 23)
Power Save
“Audio Output” (page 28)
PowerManager
Power Save
“4-1. Setting Power Saving” (page 27)
Eco Timer
“4-6. Enabling / Disabling Auto PowerOFF” (page 31)
Monitor Settings
Input Signal
“To set input signal selection” (page 43)
Power Indicator
“4-2. Setting Power Indicator” (page 28)
Language
“3-8. Setting Language” (page 25)
DDC/CI
“3-3. Enabling / Disabling DDC/CI
communication” (page 23)
Border Intensity
“To adjust brightness of non-display area”
(page 22)
Menu Settings
Orientation
“3-5. Setting Orientation” (page 24)
Logo
“3-6. Showing and hiding the EIZO logo”
(page 24)
Menu Position
“3-7. Changing Setting Menu Display
Position” (page 25)
Reset
“To reset all adjustments to the default
settings” (page 26)
Information
“6-6. Displaying Monitor Information”
(page 44)
*1 The adjustment / settings available on the “Color” menu depend on the selected Color mode (see “Adjustable
settings in each mode” (page 15)).
*2 These functions can be adjusted with analog input.
Chapter 1 Introduction
11
Chapter 2 Adjusting Screens
2-1. Compatible Resolutions
The monitor supports the following resolutions.
●●Analog Input (D-Sub)
Resolution
Applicable Signals
640 × 480
800 × 600
1024 × 768
1280 × 720*1
1280 × 960
1280 × 1024
1600 × 1200
1680 × 1050
1920 × 1200*2
VGA
VESA
VESA
CEA-861
VESA
VESA
VESA
VESA CVT, VESA CVT RB
VESA CVT, VESA CVT RB
Vertical Scan
Frequency
Dot Clock
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
202.5 MHz
(Max.)
Vertical Scan
Frequency
Dot Clock
●●Digital Input (DVI-D)
Resolution
Applicable Signals
640 × 480
800 × 600
1024 × 768
1280 × 720*1
1280 × 960
1280 × 1024
1600 × 1200
1680 × 1050
1920 × 1200*2
VGA
VESA
VESA
CEA-861
VESA
VESA
VESA
VESA CVT, VESA CVT RB
VESA CVT RB
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
162 MHz
(Max.)
Vertical Scan
Frequency
Dot Clock
●●Digital Input (DisplayPort)
Resolution
Applicable Signals
640 × 480
720 × 480 (4:3)
720 × 480 (16:9)
800 × 600
1024 × 768
1280 × 720*1
1280 × 960
1280 × 1024
1600 × 1200
1680 × 1050
1920 × 1200*2
VGA, CEA-861
CEA-861
CEA-861
VESA
VESA
CEA-861
VESA
VESA
VESA
VESA CVT, VESA CVT RB
VESA CVT RB
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
162 MHz
(Max.)
*1 For this resolution, the “Screen Size” setting is “Full Screen” (see “2-5. Screen Size Changing” (page 22)).
*2 Recommended resolution
12
Chapter 2 Adjusting Screens
2-2. Setting the Resolution
When you connect the monitor to the PC and find that the resolution is improper, or when you want to change the
resolution, follow the procedure below.
●●Windows 10
1. Right-click the mouse anywhere on the desktop except on icons.
2. From the displayed menu, click “Display settings”.
3. If multiple monitors are connected to the computer, select the monitor.
4. Select the resolution from the “Resolution” pull-down menu.
5. When a confirmation screen appears, click “Keep changes”.
●●Windows 8.1 / Windows 7
1. For Windows 8.1, click the “Desktop” tile on the Start Screen to display the desktop.
2. Right-click the mouse anywhere on the desktop except on icons.
3. From the displayed menu, click “Screen resolution”.
4. Select the monitor, and select the resolution from the “Resolution” pull-down menu.
5. Click the “OK” button.
6. When a confirmation dialog box is displayed, click “Keep changes”.
●●OS X Mountain Lion (10.8) or later
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog box is displayed, click “Displays”. (For OS X Mountain Lion (10.8),
click “Displays” for “Hardware”.)
3. On the displayed dialog box, select the “Display” tab, then choose “Scaled” for “Resolutions”.
4. The list of selectable resolutions is displayed. Select the desired resolution. If the desired resolution is not
displayed in the list, hold down the Option key and select “Scaled”.
5. Your selection will be reflected immediately. When you are satisfied with the selected resolution, close the
window.
●●Mac OS X 10.7
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.
3. On the displayed dialog box, select the “Display” tab and select desired resolution in the “Resolutions” field.
4. Your selection will be reflected immediately. When you are satisfied with the selected resolution, close the
window.
Chapter 2 Adjusting Screens
13
2-3. Adjusting Color
●●To select the display mode (color mode)
This function allows easy selection of a desired mode according to monitor application.
Display Modes
Mode
Purpose
User1
Select this to define a desired set of parameter settings.
User2
sRGB
Suitable for color matching with sRGB compatible peripherals.
Paper
Produces a printed paper effect. Suitable for displaying images from media such as books
and documents.
Movie
Suitable for playing back animated images.
The mode menu
appears.
Procedure
1. Press
.
The mode menu appears at the bottom left of the screen.
2. The mode among the list is highlighted in turn each time
You can switch the mode with
or
is pressed.
while the mode menu is displayed.
Note
• The Setting menu and the Mode menu cannot be displayed at the same time.
●●To perform advanced adjustments
The “Color” menu of the Setting menu allows you to set and save the independent color adjustment for each
mode.
Attention
• It takes about 30 minutes for the monitor display to stabilize. Please wait 30 minutes or more after the monitor power
has been turned on, and then adjust the monitor.
• Perform the range adjustment first when adjusting color for analog signals (see “To adjust color gradation
automatically” (page 21)).
• The same image may be seen in different colors on multiple monitors due to their monitor-specific characteristics.
Make fine color adjustment visually when matching colors on multiple monitors.
14
Chapter 2 Adjusting Screens
●●Adjustable settings in each mode
The adjustable settings depend on the mode. (Non-adjustable or non-settable function cannot be selected.)
√: Adjustable -: Not adjustable
Function
Color Mode
User1
User2
sRGB
Paper
Movie
Brightness
√
√
√
√
√
Contrast
√
√
-
-
√
Temperature
√
√
-
√
√
Gamma
√
√
-
-
-
Saturation
√
√
-
-
√
Hue
√
√
-
-
√
Gain
√
√
-
-
-
√
√
√
√
√
Advanced Settings
Color Reset
●●To adjust brightness
The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD back
panel).
Adjustable range
0 to 100
Procedure
.
1. Press
2. Use
3. Press
or
for adjustment.
to exit.
Note
• If you feel that the image is too dark even if the brightness is set to 100, adjust the contrast.
• Alternatively, you can use “Brightness” under “Color” in the Adjustment menu to adjust it.
• To adjust the screen brightness automatically and comfortably, see “4-3. Enabling / Disabling Automatic Brightness
Adjustment” (page 28).
Chapter 2 Adjusting Screens
15
●●To adjust contrast
The brightness of the screen is adjusted by varying the video signal level.
Adjustable range
0 to 100
Procedure
1. Choose “Color” in the Setting menu, and press
.
.
2. Choose “Contrast” in the “Color” menu, and press
The “Contrast” menu appears.
3. Use
or
for adjustment.
to exit.
4. Press
Note
• In the contrast of 50, every color gradation is displayed.
• When adjusting the monitor, it is recommended to perform the brightness adjustment which may not lose the gradation
characteristics, prior to the contrast adjustment.
• Perform the contrast adjustment in the following cases.
- When you feel the image is too dark even if the brightness is set to 100 (Set the contrast to higher than 50.)
●●To adjust color temperature
Color temperature can be adjusted.
The color temperature is normally used to express the hue of “White” and / or “Black” by a numerical value.
The value is expressed in degrees “K” (Kelvin).
The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like the flame
temperature. A gain preset value is set for each color temperature setting value.
Adjustable range
Off, 4000 K-10000 K (specified by every 500 K unit, including 9300 K)
Procedure
1. Choose “Color” in the Setting menu, and press
2. Choose “Temperature” in the “Color” menu, and press
.
.
The “Temperature” menu appears.
3. Use
4. Press
or
for adjustment.
to exit.
Note
•
•
•
•
16
The value shown in “K” is available only as reference.
“Gain” allows you to perform more advanced adjustment (see “To adjust gain” (page 18)).
If you set to “Off”, the image is displayed in the preset color of the monitor (Gain: 100 for each RGB).
When gain is changed, the color temperature is changed to “Off”.
Chapter 2 Adjusting Screens
●●To adjust gamma
Gamma can be adjusted. The brightness of the monitor varies depending on the input signal, however, the
variation rate is not proportional to the input signal. To keep the balance between the input signal and the
brightness of the monitor is called as “Gamma correction”.
Adjustable range
1.8, 2.0, 2.2
Procedure
1. Choose “Color” in the Setting menu, and press
.
.
2. Choose “Gamma” in the “Color” menu, and press
The “Gamma” menu appears.
3. Use
or
for adjustment.
to exit.
4. Press
Note
• If “Paper” is selected for the color mode, “Paper” is displayed for the gamma value. The setting “Paper” is specially
meant to get the displayed image look like it is printed on paper.
●●To adjust the color saturation
This function allows you to adjust color saturation.
Adjustable range
-50 to 50
Procedure
1. Choose “Color” in the Setting menu, and press
.
2. Choose “Advanced Settings” in the “Color” menu, and press
3. Choose “Saturation” in the “Advanced Settings” menu, and press
.
.
The “Saturation” menu appears.
4. Use
5. Press
or
for adjustment.
to exit.
Attention
• Using this function may make some color gradations unavailable for display.
Note
• The minimum value (-50) changes the screen to monochrome.
Chapter 2 Adjusting Screens
17
●●To adjust hue
This function allows you to adjust hue.
Adjustable range
-50 to 50
Procedure
1. Choose “Color” in the Setting menu, and press
.
.
2. Choose “Advanced Settings” in the “Color” menu, and press
3. Choose “Hue” in the “Advanced Settings” menu, and press
.
The “Hue” menu appears.
4. Use
or
5. Press
for adjustment.
to exit.
Attention
• Using this function may make some color gradations unavailable for display.
●●To adjust gain
The brightness of each color component red, green, and blue is called “Gain”. You can change the hue of
“white” by adjusting gain.
Adjustable range
0 to 100
Procedure
1. Choose “Color” in the Setting menu, and press
.
.
2. Choose “Advanced Settings” in the “Color” menu, and press
3. Choose “Gain” in the “Advanced Settings” menu, and press
.
The “Gain” menu appears.
4. Adjust gain with
5. Press
or
for each of red, green, and blue.
to exit.
Attention
• Using this function may make some color gradations unavailable for display.
Note
• The value of gain changes with that of color temperature.
• When gain is changed, the color temperature is changed to “Off”.
18
Chapter 2 Adjusting Screens
2-4. Screen Adjustment
●●Digital Signal Input
When digital signals are input, images are displayed correctly based on the preset data of the monitor, but if
characters and / or lines appear blurred, go to “To modify blurred characters / lines” (page 21).
When performing more advanced adjustment, see “2-3. Adjusting Color” (page 14) and subsequent pages.
●●Analog Signal Input
Attention
• It takes about 30 minutes for the monitor display to stabilize. Please wait 30 minutes or more after the monitor power
has been turned on, and then adjust the monitor.
• The Self Adjust (automatic screen adjustment) function does not work for the images under the resolution of 800 × 600
(SVGA).
• The self adjustment (or automatic screen adjustment) function works correctly when an image is fully displayed over the
Windows or Macintosh display area. They do not work properly in the cases below:
- When an image is displayed only on a part of the screen (command prompt window, for example)
- When a black background (wallpaper, etc.) is in use
Also, these functions cannot work properly in some graphic boards.
The monitor screen adjustment is used to suppress flickering of the screen or adjust screen position and screen
size correctly according to the PC to be used.
Note
• The Self Adjust function works when all of the following conditions are satisfied:
- When a signal is input into the monitor for the first time or when a resolution or vertical / horizontal scan frequency
not used before is set
If the screen is not displayed correctly even after performing the Self Adjust operation, adjust the screen
according to the procedures on the following pages to use the monitor comfortably.
Setting Procedures
1. Adjust flickering, screen position, and size automatically.
Procedure
1. Choose “Screen” in the Setting menu, and press
.
2. Choose “Analog Adjustment” in the “Screen” menu, and press
.
3. Choose “Auto Screen Adjust” in the “Analog Adjustment” menu, and press
4. Select “Yes” with
or , and press
.
.
Flickering, screen position, and screen size are corrected by the auto-adjustment function.
If the screen is not displayed correctly even after performing the auto adjustment, perform adjustments
according to the following procedure. If the screen is displayed correctly, go to “3. Adjusting color gradation.”
(page 21).
Chapter 2 Adjusting Screens
19
2. Choose “Screen” from the Setting menu to perform advanced adjustments.
Adjust the clock, phase and position, in this order.
●●To eliminate vertical bars
Procedure
.
1. Choose “Analog Adjustment” in the “Screen” menu, and press
2. Choose “Clock” in the “Analog Adjustment” menu, and press
.
The “Clock” menu appears.
3. Adjust the clock with
Press
or
4. Press
or
to eliminate vertical bars.
slowly so as not to miss the adjustment point.
to exit.
When blurring, flickering or bars appear on the screen after adjustment, proceed to “To remove flickering or blurring ”.
●●To remove flickering or blurring
Procedure
.
1. Choose “Analog Adjustment” in the “Screen” menu, and press
2. Choose “Phase” in the “Analog Adjustment” menu, and press
.
The “Phase” menu appears.
3. Adjust the phase with
4. Press
or
to minimize flickering or blurring.
to exit.
When vertical bars appear on the screen after adjustment, go back to “To eliminate vertical bars ”.
(Clock → Phase → Position)
Attention
• Flickering or blurring may not be eliminated depending on your PC or graphics board.
20
Chapter 2 Adjusting Screens
●●To correct the screen position
Note
• Since the number of pixels and the pixel positions are fixed on the LCD monitor, only one position is provided to display
images correctly. The position adjustment is made to shift an image to the correct position.
Procedure
1. Choose “Analog Adjustment” in the “Screen” menu, and press
.
2. Choose “Hor.Position” or “Ver.Position” from the “Analog Adjustment” menu, and press
.
The “Hor. Position” or “Ver. Position” menu appears.
3. Adjust the position with
or .
to exit.
4. Press
3. Adjusting color gradation.
●●To adjust color gradation automatically
Every color gradation (0 to 255) can be displayed by adjusting the signal output level.
Procedure
1. Choose “Screen” in the Setting menu, and press
.
2. Choose “Analog Adjustment” in the “Screen” menu, and press
.
3. Choose “Auto Range Adjust” in the “Analog Adjustment” menu, and press
4. Select “Yes” with
or , and press
.
.
The output range is set automatically.
4. Modify blurred characters or lines.
●●To modify blurred characters / lines
When an image is displayed with a resolution other than recommended, the characters or lines of the
displayed image may blur.
Attention
• Smoothing setting may not be required depending on the display resolution. (You cannot choose the smoothing icon.)
Adjustable range
1 to 5
Procedure
1. Choose “Screen” in the Setting menu, and press
2. Choose “Smoothing” in the “Screen” menu, and press
.
.
The “Smoothing” menu appears.
3. Use
4. Press
or
for adjustment.
to exit.
Chapter 2 Adjusting Screens
21
2-5. Screen Size Changing
●●Screen Size Changing
The image with the resolution other than the recommended resolution is displayed in full screen automatically.
You can change the screen size by using the “Screen Size” function.
Setting
Function
Full Screen
Displays an image in full screen. Images are distorted in some cases because the vertical
rate is not equal to the horizontal rate.
Enlarged
Displays an image in full screen. In some cases, a blank horizontal or vertical border
appears to equalize the vertical rate and the horizontal rate.
Example: Image size 1024 × 768
Full Screen
Enlarged
Procedure
.
1. Choose “Screen” in the Setting menu, and press
.
2. Choose “Screen Size” in the “Screen” menu, and press
The “Screen Size” menu appears.
3. Select either “Full Screen” or “Enlarged” with
or .
to exit.
4. Press
Attention
• When a 1280 × 720 or 1920 × 1080 resolution image is displayed, the screen size is fixed to “Full Screen”.
●●To adjust brightness of non-display area
When the screen size setting is “Enlarged”, a border (black area with no image) around the image appears.
Border
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
.
2. Choose “Border Intensity” in the “Monitor Settings” menu, and press
The “Border Intensity” menu appears.
3. Use
4. Press
22
or
for adjustment.
to exit.
Chapter 2 Adjusting Screens
.
Chapter 3 Setting Monitor
3-1. Adjusting Volume
This function allows you to adjust the volume.
Adjustable range
0 to 30
Procedure
.
1. Press
2. Use
or
3. Press
for adjustment.
to exit.
Note
• The volume for the speakers and the headphone can be set individually.
3-2. Selecting sound source while using the DisplayPort
signal input
This function allows you to switch sound source during DisplayPort signal input. You can select the Stereo Mini
Jack or DisplayPort.
Procedure
1. Choose “Sound” in the Setting menu, and press
.
.
2. Choose “Source” in the “Sound” menu, and press
The “Source” menu appears.
3. Select “Stereo Mini Jack” or “DisplayPort” with
4. Press
or .
to exit.
Note
• This function is available with DisplayPort signal input.
3-3. Enabling / Disabling DDC/CI communication
This function allows you to enable / disable the DDC/CI communication.
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
2. Choose “DDC/CI” in the “Monitor Settings” menu, and press
.
.
The “DDC/CI” menu appears.
3. Select “On” or “Off” with
4. Press
or .
to exit.
Note
• The DisplayPort input of this monitor does not support DDC/CI communication.
Chapter 3 Setting Monitor
23
3-4. Locking Operation Buttons
This function allows you to lock the settings to prevent them being changed.
Procedure
1. Press
to turn off the monitor.
while pressing
2. Hold down
to turn on the monitor.
The Lock / Unlock setting is toggled by performing the operation in step 2.
Note
• The following operations are available even if the buttons are locked:
- Turning on or off the monitor with the Power button
3-5. Setting Orientation
This function allows you to change the orientation of the Setting menu when using the monitor screen in vertical
display position.
Procedure
.
1. Choose “Monitor Settings” in the Setting menu, and press
.
2. Choose “Menu Settings” in the “Monitor Settings” menu, and press
.
3. Choose “Orientation” in the “Menu Settings” menu, and press
The “Orientation” menu appears.
4. Select “Landscape” or “Portrait” with
5. Press
or .
to exit.
6. When selecting “Portrait”, turn the monitor screen 90˚ in clockwise direction.
Attention
• Be sure that the cables are correctly connected.
• Be sure to turn the monitor screen after pulling up the screen to the uppermost position of the stand and setting the
screen tilted upward.
Note
• For using the monitor with “Portrait” position, the graphics board supporting portrait display is required. When placing
the monitor in a “Portrait” position, settings of your graphics board need to be changed. Refer to the User’s Manual of
the graphics board for details.
3-6. Showing and hiding the EIZO logo
When the monitor is turned on, the EIZO logo appears on the screen. You can choose to show or hide the display of
the EIZO logo.
Procedure
.
1. Choose “Monitor Settings” in the Setting menu, and press
2. Choose “Menu Settings” in the “Monitor Settings” menu, and press
3. Choose “Logo” in the “Menu Settings” menu, and press
The “Logo” menu appears.
4. Select “On” or “Off” with
5. Press
24
to exit.
Chapter 3 Setting Monitor
or .
.
.
3-7. Changing Setting Menu Display Position
You can change the display position of the Setting menu.
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
.
.
2. Choose “Menu Settings” in the “Monitor Settings” menu, and press
.
3. Choose “Menu Position” in the “Menu Settings” menu, and press
The “Menu Position” menu appears.
4. Choose the position with
5. Press
or .
to exit.
3-8. Setting Language
This function allows you to select a language for the Setting menu or messages.
Selectable languages
English, German, French, Spanish, Italian, Swedish, Japanese, Simplified Chinese, Traditional Chinese
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
2. Choose “Language” in the “Monitor Settings” menu, and press
.
.
The “Language” menu appears.
3. Choose a language with
4. Press
or .
to exit.
Chapter 3 Setting Monitor
25
3-9. Resetting the Monitor to the Default Settings
The setting values are reset to the default settings.
Attention
• After resetting, you cannot undo the operation.
●●To reset the color adjustments
This function only resets the color adjustments for the currently selected mode to the default settings.
Procedure
1. Choose “Color” in the Setting menu, and press
.
2. Choose “Color Reset” in the “Color” menu, and press
3. Select “Yes” with
.
or .
.
4. Press
The color adjustments revert to the default settings.
●●To reset “EcoView Sense Settings”
This function resets adjustments for “EcoView Sense Settings” to the default settings.
Procedure
1. Press
.
2. Choose “EcoView Sense Settings” in the “EcoView Menu”, and press
.
3. Choose “Reset” in the “EcoView Sense Settings”, and press
4. Select “Yes” with
5. Press
.
or .
.
The “EcoView Sense Settings” adjustments revert to the default settings.
Note
• “EcoView Sense Settings” can be changed and reset only when “EcoView Sense” is set to “On” (see “4-4. Setting the
power saving mode when a person leaves the monitor” (page 29)).
●●To reset all adjustments to the default settings
This function resets all adjustments to the default settings.
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
2. Choose “Reset” in the “Monitor Settings” menu, and press
3. Select “Yes” with
4. Press
or .
.
All adjustments revert to the default settings.
26
Chapter 3 Setting Monitor
.
.
Chapter 4 Power Saving Functions
4-1. Setting Power Saving
●●Monitor
This function allows you to set the monitor into the power saving mode according to the PC status. When the
monitor has shifted to the power saving mode, the images on the screen are not displayed.
Attention
• Turning off the main power switch or unplugging the power cord completely shuts off power supply to the monitor.
• When the monitor is in power saving mode, devices connected to the USB downstream port will still work. Therefore,
power consumption of the monitor varies with connected devices even in the power saving mode.
• Power consumption varies even when the stereo mini jack cable is connected.
Note
• The monitor changes to the power saving mode about 15 seconds after the signal input ceases to be detected.
Procedure
.
1. Choose “PowerManager” in the Setting menu, and press
.
2. Choose “Power Save” in the “PowerManager” menu, and press
The “Power Save” menu appears.
3. Select “On” or “Off” with
4. Press
or .
to exit.
Power Saving System
Analog Signal Input
This monitor complies with the VESA DPM standard.
PC
On
Power saving
mode
STAND-BY
SUSPENDED
OFF
Power Off
Monitor
Power Indicator
Operating
White
Power saving mode
Orange
Power saving mode
Orange
Digital Signal Input
• DVI
This monitor complies with the DVI DMPM standard.
• DisplayPort
This monitor complies with the DisplayPort Standard V1.1a.
PC
Monitor
Power Indicator
On
Operating
White
Power saving mode
Power saving mode
Orange
Power Off
Power saving mode
Orange
Exiting the power saving mode
If the monitor receives input, it automatically exits the power saving mode and returns to the normal display
mode.
Chapter 4 Power Saving Functions
27
●●Audio Output
This monitor allows you to turn off the audio output from the speakers / headphone at the power saving mode.
Procedure
1. Choose “Sound” in the Setting menu, and press
.
2. Choose “Power Save” in the “Sound” menu, and press
.
The “Power Save” menu appears.
3. Select “Sound On” or “Sound Off” with
or .
to exit.
4. Press
4-2. Setting Power Indicator
This function allows you to set the power indicator (white) ON / OFF in the monitor ON condition.
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
.
.
2. Choose “Power Indicator” in the “Monitor Settings” menu, and press
The “Power Indicator” menu appears.
3. Select “On” or “Off” with
or .
to exit.
4. Press
4-3. Enabling / Disabling Automatic Brightness
Adjustment
●●Auto EcoView
The ambient light sensor on the front side of the monitor detects the environmental brightness to adjust the
screen brightness automatically and comfortably by using the Auto EcoView function.
Attention
• Be careful not to block the ambient light sensor on the lower side of the monitor when using the Auto EcoView function.
Procedure
1. Press
.
2. Choose “Auto EcoView” in the “EcoView Menu” menu, and press
.
The “Auto EcoView” menu appears.
3. Select “High”, “Standard”, or “Off” with
4. Press
or .
to exit.
Note
• As “Brightness” in the Setting menu is changed, the auto adjustment range for Auto EcoView is also changed.
• Set to “High” if you feel a little brighter with “Standard” setting status.
28
Chapter 4 Power Saving Functions
●●EcoView Optimizer 2
Using the EcoView Optimizer 2 function automatically adjusts the screen brightness according to the white
level of the input signal. This function can reduce the power consumption while maintaining the brightness
specified by the input signal.
Procedure
1. Press
.
2. Choose “EcoView Optimizer 2” in the “EcoView Menu” menu, and press
.
The “EcoView Optimizer 2” menu appears.
3. Select “On” or “Off” with
or .
to exit.
4. Press
Note
• When “Movie” is selected from the color mode, the setting is turned “Off”.
• When the EcoView Optimizer 2 function is “On”, the appearance of pale color may change. If that bothers you, set this
function to “Off”.
4-4. Setting the power saving mode when a person
leaves the monitor
The sensor on the front side of the monitor detects the movement of a person by using the EcoView Sense function.
When a person moves away from the monitor, it shifts to the power saving mode automatically and does not display
the images on the screen to reduce the power consumption. When a person comes near the monitor again, it
recovers from the power saving mode and displays the images. The sensitivity and time until the power saving
mode is activated can be set according to the monitor usage environment and movement of the user.
Note
• At the time of shifting to power saving mode, the message that indicates shifting is displayed.
Procedure
1. Press
.
2. Choose “EcoView Sense” in the “EcoView Menu”, and press
.
The “EcoView Sense” menu appears.
3. Select “On” or “Off” with
4. Press
or .
to exit.
Chapter 4 Power Saving Functions
29
5. When “On” is selected, select “EcoView Sense Settings” for setting the details.
Item
Setting Range
Description
Time
5, 30 sec
1, 3, 5, 10, 15, 30, 45,
60 min
Specifies the time from when a person leaves the monitor until the
“No Presence detected” message appears. The monitor shifts to
the power saving mode about 20 seconds after the message is
displayed.
Sensitivity
Level 5
Level 4
Level 3
Level 2
Level 1
When the setting level is high (“Level 5” at maximum), even minor
movements of a person are detected, causing the monitor to shift
to the power saving mode only infrequently. On the other hand,
when the setting level is low (“Level 1” at minimum), only major
movements of a person are detected, allowing the monitor to shift
to the power saving mode frequently. EcoView Sense is activated
when the sensor on the front side of the monitor detects the
movement of heat. Therefore, the sensitivity should be changed
depending on the typical user’s clothes or the typical room
temperature. If the monitor shifts to or recovers from the power
saving mode contrary to your expectations, try changing the setting
level.
Reset
-
This function resets all adjustments to the default settings.
Note
• When the monitor is used in the “Portrait” direction, the detection sensitivity is lower than the “Landscape” direction.
Try increasing the sensitivity setting value when switching the mode to the power saving mode.
• To use the monitor comfortably, increase the sensitivity for high temperatures, which reduces the detection sensitivity,
and reduce the sensitivity for low temperatures, which increases the detection sensitivity.
30
Chapter 4 Power Saving Functions
4-5. Checking the power saving level
The EcoView menu allows you to check Power Reduction, CO2 Reduction, and Eco Performance Level. The more
indicators light up representing the Eco Performance Level, the higher the power saving level attained.
Example:
Indicator
Procedure
1. Press
.
The “EcoView Menu” menu appears.
Note
• Power reduction: the backlight’s reduction of power consumption as a result of the adjusted brightness value.
CO2 reduction: converted from the “Power reduction” value, this is an estimate of the quantity of CO2 emissions reduced
when using the monitor for 1 hour.
* The numeric value is a result of a calculation based on a default setting (0.000555 t -CO2/kWh) determined by a Japanese
ministerial ordinance (2006, Ministry of Economy, Trade and Industry, Ministry of Environment, civil code article 3) and
may differ depending on country and year.
4-6. Enabling / Disabling Auto Power-OFF
This function allows you to switch the setting to turn off the monitor automatically after a specified time has passed
in the power saving mode.
Adjustable range
Off, 0, 1, 2, 3, 5, 10, 15, 20, 25, 30, 45 min, 1, 2, 3, 4, 5 h
Procedure
.
1. Choose “PowerManager” in the Setting menu, and press
2. Choose “Eco Timer” in the “PowerManager”, and press
3. Select “Off” or time to turn off the monitor with
4. Press
.
or .
to exit.
Chapter 4 Power Saving Functions
31
Chapter 5 Troubleshooting
If a problem still remains after applying the suggested remedies, contact your local EIZO representative.
5-1. No picture
Problem
1. No picture
• Power indicator does not light.
Possible cause and remedy
•
•
•
•
Check whether the power cord is connected properly.
Turn the main power switch on.
Press .
Turn off the main power, and then turn it on again a few
minutes later.
• Power indicator is lighting white.
• Increase “Brightness”, “Contrast”, or “Gain” in the Setting
menu (see “To perform advanced adjustments” (page 14)).
• Power indicator is lighting orange.
•
•
•
•
Switch the input signal with
.
Move the mouse or press any key on the keyboard.
Check whether the PC is turned on.
When the EcoView Sense function is “On”, the monitor
may have shifted to the power saving mode. Come near
to the monitor. If the screen is not displayed, move the
mouse or press any key on the keyboard.
• Depending on the PC and graphics board, the input signal
is not detected and the monitor does not recover from
the power saving mode. If the screen is not displayed
even after moving the mouse or pressing any key on the
keyboard, turn the monitor off and on using its power
button. When the screen is displayed, execute the
following procedure. The problem may be improved.
1.
2.
Press
to turn off the monitor.
Hold down
while pressing to turn on the
monitor.
“x” is displayed on the menu title of “Information” of the
Setting menu (see “6-6. Displaying Monitor Information”
(page 44)).
3. Reboot the PC.
To return to the previous setting, perform steps 1 to 3
again.
• Power indicator is flashing orange.
32
Chapter 5 Troubleshooting
• This problem may occur for the DisplayPort input.
Connect via the signal cable specified by EIZO, turn off
the monitor, and then turn it on again.
Problem
2. The message below appears.
• The message shows that the input signal is
out of the specified frequency range.
Example:
Possible cause and remedy
This message appears when the signal is not input correctly
even when the monitor functions properly.
• Check whether the PC is configured to meet the resolution
and vertical scan frequency requirements of the monitor
(see “2-1. Compatible Resolutions” (page 12)).
• Reboot the PC.
• Select an appropriate setting using the graphics board’s
utility. Refer to the User’s Manual of the graphics board
for details.
5-2. Imaging problems (for both digital and analog)
Problem
Possible cause and remedy
1. The screen is too bright or too dark.
• Use “Brightness” or “Contrast” in the Setting menu to
adjust it. (The LCD monitor backlight has a limited life
span. When the screen becomes dark or begins to flicker,
contact your local EIZO representative.)
• If the screen is too bright, turn on Auto EcoView. The
monitor detects the environmental brightness to adjust the
screen brightness automatically.
2. Characters are blurred.
• Check whether the PC is configured to meet the resolution
and vertical scan frequency requirements of the monitor
(see “2-1. Compatible Resolutions” (page 12)).
• When an image is displayed with a resolution other than
recommended, the characters or lines of the displayed
image may blur. Use “Smoothing” and “Screen Size” in the
Setting menu to adjust the display (see “To modify blurred
characters / lines” (page 21), and “Screen Size Changing”
(page 22)).
3. Afterimages appear.
• Afterimages are particular to LCD monitors. Avoid
displaying the same image for a long time.
• Use the screen saver or power save function to avoid
displaying the same image for extended periods of time.
4. Green/red/blue/white dots or defective
dots remain on the screen.
• This is due to LCD panel characteristics and is not a
failure.
5. Interference patterns or pressure marks
remain on the screen.
• Leave the monitor with a white or black screen. The
symptom may disappear.
6. Noise appears on the screen.
• When entering the signals of HDCP system, the normal
images may not be displayed immediately.
Chapter 5 Troubleshooting
33
5-3. Imaging problems (for digital only)
Problem
Possible cause and remedy
1. The monitor configuration is changed to
single under the multiple monitor configuration (when DisplayPort is connected).
• When two monitors are connected to one PC using
DisplayPort, and the power to one of the monitors is
turned off with the power button, the screen setting may
be changed to the single monitor configuration. In such a
case, enable the “DP HotPlug” function with the following
procedures. Enabling this function may increase the
power consumption.
1. Press to turn off the monitor.
2. Hold down while pressing to turn on the monitor.
Each time the operation enables / disables this function
alternatively.
The current setting status can be identified based on the
color used to display the input port or signal error.
Setting
Input port
Signal Error
Disable
(default
setting)
Enable
5-4. Imaging problems (for analog only)
Problem
34
Possible cause and remedy
1. Display position is incorrect.
• Use “Position” in the Setting menu to correct the image
position (see “To correct the screen position” (page 21)).
• If the problem persists, use the graphics board’s utility if
available to change the display position.
2. Vertical bars appear on the screen or a
part of the image is flickering.
• Use “Clock” in the Setting menu to adjust it (see “To
eliminate vertical bars” (page 20)).
3. Whole screen is flickering or blurring.
• Use “Phase” in the Setting menu to adjust it (see “To
remove flickering or blurring” (page 20)).
Chapter 5 Troubleshooting
5-5. Other problems
Problem
Possible cause and remedy
1. The Setting menu does not appear.
• Check whether the operation lock function is active (see
“3-4. Locking Operation Buttons” (page 24)).
2. The “Smoothing” on the Setting menu
“Screen” cannot be selected.
• If the resolution is 1920 × 1200, you cannot select
smoothing.
3. The auto adjustment function does not
work.
• This function does not work during digital signal input.
• This function operates correctly when images are
displayed in the entire viewable area such as in Windows.
It does not work properly when an image is displayed only
on a part of the screen (command prompt window, for
example) or when a black background (wallpaper, etc.) is
in use.
• This function does not work correctly with some graphics
boards.
4. No audio output.
• Check whether the stereo mini jack cable is connected
properly.
• Check whether volume is set to 0.
• Check the setting of the PC and the audio playback
software.
• During DisplayPort signal input, check the “Source”
setting (see “3-2. Selecting sound source while using the
DisplayPort signal input” (page 23)).
5. (When using EcoView Sense)
The images remain to be displayed when
you move away from the monitor. / The
images do not reappear when you come
near it.
• Check the setting environment of the monitor. Presence
Sensor may not work correctly in the following
environments.
--The monitor is located in a place affected by wind.
--There is some heat emitting device near the monitor.
--There is some obstacle in front of the sensor.
• Check whether any dirt on the sensor. Clean the sensor
with a soft cloth.
• Check whether you are in front of the monitor. The
EcoView Sense function is activated when the sensor on
the front side of the monitor detects the movement of heat.
• In the high temperature conditions, the monitor may not
recover from the power saving mode. If the screen is not
displayed even after moving the mouse or pressing any
key on the keyboard, turn the monitor off and on using its
power button. When the screen is displayed, increase the
detection sensitivity value (see “4-4. Setting the power
saving mode when a person leaves the monitor” (page 29)).
6. USB devices connected to the monitor do
not work.
• Check whether the USB cable is connected correctly (see
“6-5. Using the USB Hub Function” (page 43)).
• Try changing to a different USB port on the PC.
• Try changing to a different USB port on the monitor.
• Reboot the PC.
• If the peripheral devices work correctly when the PC and
peripheral devices are connected directly, please contact
your local EIZO representative.
• Check whether the PC and OS are USB compliant. (For
USB compliance of the respective devices, consult their
manufacturers.)
• Check the PC’s BIOS setting for USB when using
Windows. (Refer to the manual of the PC for details.)
Chapter 5 Troubleshooting
35
Chapter 6 Reference
6-1. Attaching the Optional Arm
An optional arm (or an optional stand) can be attached by removing the stand section. Please refer to our web site
for the corresponding optional arm (or optional stand). http://www.eizoglobal.com
Attention
• When attaching an arm or stand, follow the instructions of their User’s Manual.
• When using another manufacturer’s arm or stand, confirm the following in advance and select one conforming to the VESA
standard. Use the screws securing the unit and the stand.
- Clearance between the screw holes: 100 mm × 100 mm
- Thickness of plate: 2.6 mm
- Strong enough to support weight of the monitor unit (except the stand) and attachments such as cables.
• When using an arm or stand, attach it to meet the following tilt angles of the monitor.
- Up 45˚, down 45˚ (horizontal display, and vertical display rotated 90 degrees clockwise)
• Connect the cables after attaching an arm or stand.
• Do not move the removed stand up and down. Doing so may result in injury or device damage.
• The monitor and arm or stand are heavy. Dropping them may result in injury or equipment damage.
• When setting the monitor to the portrait style, turn the monitor screen 90˚ in clockwise direction.
Procedure
1. Lay the LCD monitor on a soft cloth spread over on a stable surface with the
panel surface facing down.
2. Remove the stand.
Prepare a screwdriver. Loosen the screws (four) securing the unit and the stand with the screwdriver.
3. Attach the arm or stand to the monitor.
Secure the monitor to the arm or stand using the screws specified in the User’s Manual of the arm or stand.
36
Chapter 6 Reference
6-2. Detaching/Attaching Stand Base
Detaching procedure
The stand base that was attached during setup can be detached using the following procedures.
1. Lay the LCD monitor on a soft cloth spread over on a stable surface with the
panel surface facing down.
2. Turn the fixing screw on the stand base to detach it.
Note
• The fixing screw can be removed by hand. If the fixing screw is too tight, use a coin or flathead screwdriver.
3. Turn the stand base in the counterclockwise direction to detach it.
Note
• Reattach the fixing screw onto the stand base for when the stand base is used again.
Chapter 6 Reference
37
Attaching procedure
The once removed the stand base can be attached to the monitor again with the following procedures.
1. Check that the fixing screw is firmly attached to the bottom of the stand base.
2. Place the stand base on a stable surface.
3. Insert the stand brace into the stand base.
Stand brace
Stand base
38
Chapter 6 Reference
4. Turn the stand brace in the clockwise direction until it clicks.
C li c
k!
Chapter 6 Reference
39
6-3. Attaching/Detaching Cable Holder
A cable holder is supplied with this product. Use the holder to organize the cables connected to the monitor.
Attaching procedure
1. Pass the cables through the cable holder.
2. Close the opening in the cable holder.
3. While holding the cable holder closed, attach it onto the stand.
Note
• The cable holder can be inserted either perpendicular or parallel to the stand. Change the direction of the cable holder
according to the conditions of the cables.
40
Chapter 6 Reference
Detaching procedure
1. Close the opening in the cable holder.
2. While holding the cable holder closed, remove it from the stand.
Chapter 6 Reference
41
6-4. Connecting Multiple PCs
The product has multiple connections to PCs and allows you to switch to one of the connections for display.
Connection examples
DisplayPort
connector
Digital
(DisplayPort)
Signal cable
(supplied PP200)
DisplayPort
connector
To PC 1
●●To switch among input signals
DVI-D connector
Digital (DVI)
Signal cable
(supplied FD-C39)
D-Sub
connector
Analog (D-Sub)
Signal cable
(option MD-C87)
DVI connector
D-Sub mini 15-pin
connector
To PC 2
To PC 3
The input signal switches each time
is pressed.
When the signal is switched, the active input port name appears at the top right corner of the screen.
42
Chapter 6 Reference
●●To set input signal selection
Setting
Function
Auto
The monitor recognizes the connector through which PC signals are input.
When a PC is turned off or enters the power saving mode, the monitor automatically
displays another signal.
Manual
The monitor displays the signal from the selected connector despite the signal input. Select
the input signal for display using the
operation button.
Procedure
.
1. Choose “Monitor Settings” from the Adjustment menu, and press
2. Choose “Input Signal” from “Monitor Settings”, and press
3. Select “Auto” or “Manual” with
4. Press
.
or .
to exit.
Note
• If you select “Auto”, the monitor enters the power saving mode after all the PCs have entered the power saving mode or
have been switched off.
6-5. Using the USB Hub Function
This monitor has a USB hub. It works as a USB hub when connected to a USB-compatible PC, allowing the
connection of peripheral USB devices.
Attention
• This monitor may not work depending on PC, OS or peripheral devices to be used. For USB compatibility of peripheral
devices, contact their manufacturers.
• When the monitor is in power saving mode, devices connected to the USB downstream port will still work. Therefore,
power consumption of the monitor varies with connected devices even in the power saving mode.
• When the main power of the monitor is Off, a device connected to the USB downstream port will not operate.
Chapter 6 Reference
43
●●Connection Procedure (Setup of USB Function)
1. Connect the monitor first to a PC using the signal cable, and run the PC.
2. Connect the USB cable between the USB downstream port of the PC and the USB upstream port of the
monitor.
The USB hub function is set up automatically upon connection of the USB cable.
3. Connect the peripheral USB devices to the USB downstream port of the monitor.
USB
downstream
port
USB
upstream
port
6-6. Displaying Monitor Information
This function allows you to display the model name, serial number, usage time, resolution, and input signal.
Procedure
1. Choose “Information” in the Setting menu, and press
.
The “Information” menu appears.
Attention
• When you turn on the monitor for the first time, the usage time may be more than 0 due to a factory inspection.
44
Chapter 6 Reference
6-7. Specifications
LCD Panel
Size
24.1-inch (611 mm)
Type
TFT color LCD, LED backlight
Surface treatment
Anti-Glare Hard Coating
Viewing angles
Horizontal 178˚, vertical 178˚ (CR≥10)
Dot Pitch
0.270 mm
Response Time
Gray-to-gray: 14 ms
Horizontal Scan Analog
Frequency
Digital
31 - 76 kHz
DVI
31 - 76 kHz
DisplayPort 31 - 76 kHz
Vertical Scan
Frequency
Analog
Digital
55 - 61 Hz (non-interlace)
DVI
59 - 61 Hz (non-interlace)
DisplayPort 59 - 61 Hz (non-interlace)
Resolution
Max. Dot Clock
1920 Dots × 1200 Lines
Analog
Digital
202.5 MHz
DVI
162 MHz
DisplayPort 162 MHz
Max. Display Color
Approx. 16.77 million colors
Display Area (H × V)
518.4 mm × 324.0 mm
Power Supply
100 - 240 VAC ±10 %, 50 / 60 Hz 0.65 A - 0.35 A
Power
Consumption
Screen Display On
36 W or less
Power saving mode
0.3 W or less (with no USB connections, “EcoView Sense”: “Off”, and
“Sound” - “Power Save”: “Sound Off”)
Power Off
0.3 W or less
Main Power Off
0W
Input Signal Connector
D-Sub mini 15-pin
DVI-D connector (Applicable to HDCP)
DisplayPort (Standard V1.1a, applicable to HDCP)
Applicable Format (Audio signal)
- 2ch linear PCM
(32 kHz / 44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz)
Analog Input Signal (Sync)
Separate, TTL, positive / negative
Analog Input Signal (Video)
Analog, Positive (0.7 Vp-p / 75 Ω)
Digital Signal (DVI) Transmission System TMDS (Single Link)
Audio Output
Speaker output: 1.0 W + 1.0 W
Headphone output: 2 mW + 2 mW (32 Ω)
Dimensions
(Width) ×
(Height) ×
(Depth)
Main unit
552.5 mm × 368 - 499 mm × 233 mm
Main unit (without
stand)
552.5 mm × 358 mm × 56.9 mm
Mass
Main unit
Approx. 6.7 kg
Main unit (without
stand)
Approx. 4.3 kg
Movable range
Tilt:
35˚ Up, 5˚ Down
Swivel:
344˚
Adjustable height:
140 mm (131 mm for tilt of 0˚)
Rotation:
90˚ (Clockwise)
Chapter 6 Reference
45
Environmental
Conditions
Temperature
Humidity
Air Pressure
USB
Operating:
5˚C to 35˚C
Transportation/
Storage:
-20˚C to 60˚C
Operating:
20 % to 80 % R.H. (no condensation)
Transportation/
Storage:
10 % to 90 % R.H. (no condensation)
Operating:
540 to 1,060 hPa
Transportation/
Storage:
200 to 1,060 hPa
Standard
USB Specification Revision 2.0
Port
Upstream port × 1, Downstream port × 2
Communication Speed 480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low)
Supply current
Downstream:
Max. 500mA/1 port
●●Accessories
Signal cable
Cleaning Kit
MD-C87 (D-Sub - D-Sub)
EIZO “ScreenCleaner”
For the latest information about the accessories, refer to our web site.
http://www.eizoglobal.com
46
Chapter 6 Reference
Appendix
Trademark
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing, LLC in the United States and other countries.
The DisplayPort Compliance Logo and VESA are registered trademarks of the Video Electronics
Standards Association.
The SuperSpeed USB Trident Logo is a registered trademark of USB Implementers
Forum, Inc.
DICOM is the registered trademark of the National Electrical Manufacturers Association for its standards
publications relating to digital communications of medical information.
Kensington and Microsaver are registered trademarks of ACCO Brands Corporation.
Thunderbolt is a trademark of Intel Corporation in the United States and/or other countries.
Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and
other countries.
Adobe is a registered trademark of Adobe Systems Incorporated in the United States and other
countries.
Apple, macOS, Mac OS, OS X, Macintosh and ColorSync are registered trademarks of Apple Inc.
EIZO, the EIZO Logo, ColorEdge, CuratOR, DuraVision, FlexScan, FORIS, RadiCS, RadiForce,
RadiNET, Raptor and ScreenManager are registered trademarks of EIZO Corporation in Japan and other
countries.
ColorEdge Tablet Controller, ColorNavigator, EcoView NET, EIZO EasyPIX, EIZO Monitor Configurator,
EIZO ScreenSlicer, G-Ignition, i•Sound, Quick Color Match, RadiLight, Re/Vue, Screen Administrator,
Screen InStyle and UniColor Pro are trademarks of EIZO Corporation.
All other company and product names are trademarks or registered trademarks of their respective
owners.
License
The bitmap font used for this product is designed by Ricoh Industrial Solutions Inc.
ENERGY STAR
As an ENERGY STAR Partner, EIZO Corporation has determined that this product meets
the ENERGY STAR guidelines for energy efficiency.
Appendix
47
FCC Declaration of Conformity
For U.S.A., Canada Only
FCC Declaration of Conformity
We, the Responsible Party
EIZO Inc.
5710 Warland Drive, Cypress, CA 90630
Phone: (562) 431-5011
declare that the product
Trade name: EIZO
Model: FlexScan EV2430
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures.
*
*
*
*
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Note
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep interference
within the limits of a Class B digital device.
--AC Cord
--Shielded Signal Cable (enclosed)
Canadian Notice
This Class B information technology equipment complies with Canadian ICES-003.
Cet équipement informatique de classe B est conforme à la norme NMB-003 du Canada.
48
Appendix
03V27353A1
UM-EV2430
Copyright © 2018 EIZO Corporation. All rights reserved.
1st Edition-April, 2018
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising