Eizo | EV3285 | User manual | Eizo EV3285 User Manual

Eizo EV3285 User Manual
User’s Manual
Color LCD Monitor
Important
Please read this “User’s Manual”, and “PRECAUTIONS” (separate
volume) carefully to familiarize yourself with safe and effective usage.
••Refer to the “Setup Guide” for information on the installation /
connection of the monitor.
••For the latest product information including the “User’s Manual”,
refer to our web site :
http://www.eizoglobal.com
Location of Caution Statement
This product has been adjusted specifically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specifications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information confidential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specifications are subject to change without notice.
2

Notice for this monitor
Aside from creating documents, viewing multimedia content, and other general purposes, this product is also
suited to applications such as creating CAD data and other drawings (Assuming usage of approximately 12
hours per day).
If using this product for the following kinds of applications, where an extremely high degree of reliability and
safety is required, then measures should be in place to maintain safety while using this product.
•• Transportation equipment (ships, aircraft, trains, and automobiles)
•• Safety devices (Disaster prevention systems, security control systems, etc.)
•• Life-critical devices (medical devices, such as life-support devices and operating room devices)
•• Nuclear energy control devices (Nuclear energy control systems, security control systems of nuclear facilities, etc.)
•• Major system communication devices (operation control systems of transportation systems, air traffic control systems, etc.)
This product has been adjusted specifically for use in the region to which it was originally shipped. If the
product is used outside the region, it may not operate as specified in the specifications.
This product may not be covered by warranty for uses other than those described in this manual.
The specifications noted in this manual are only applicable when the following are used:
•• Power cords provided with the product
•• Signal cables specified by us
Only use optional products manufactured or specified by us with this product.
If you place this product on a lacquer-coated desk, the color may adhere to the bottom of the stand due to
the composition of the rubber. Check the desk surface before use.
It takes about 30 minutes (under our measurement conditions) for the monitor display to stabilize. Please
wait 30 minutes or more after the monitor power has been turned on, and then adjust the monitor.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and
maintain a stable display.
When the screen image is changed after displaying the same image for extended periods of time, an
afterimage may appear. Use the screen saver or power save function to avoid displaying the same image for
extended periods of time. Depending on the image, an afterimage may appear even if it was displayed for
a short period of time. To remove such a phenomenon, change the image or keep the power turned off for
several hours.
If the monitor displays continuously over a long period of time, dark smudges or burn-in may appear. To
maximize the life of the monitor, we recommend the monitor be turned off periodically.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer
to “Cleaning” (page 4)).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may
appear on the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994 % or higher.
The backlight of the LCD panel has a fixed lifetime. Depending on the usage pattern, such as usage for
long continuous periods, the lifespan of the backlight may run out sooner, requiring replacement. When the
screen becomes dark or begins to flicker, please contact your local EIZO representative.
Do not press on the LCD panel or edge of the frame strongly, as this may result in display malfunctions, such
as interference patterns, etc. If pressure is continuously applied to the LCD panel surface, the liquid crystal
may deteriorate or the LCD panel may be damaged. (If the pressure marks remain on the panel, leave the
monitor with a black or white screen. The symptom may disappear.)
Notice for this monitor
3
Do not scratch or press on the LCD panel with any sharp objects, at this may result in damage to the LCD
panel. Do not attempt to brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew
condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the
monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage to the
monitor.
Cleaning
The stains on the cabinet and LCD panel surface can be removed by moistening part of a soft cloth with water.
Attention
•• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet
or LCD panel, and also quality deterioration of the image.
•• Never use thinner, benzine, wax, or abrasive cleaner as they may damage the cabinet or LCD panel surface.
Note
•• It is recommended that ScreenCleaner (available as an option) be used to clean the cabinet and LCD panel surface.
To use the monitor comfortably
•• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor
according to the environmental conditions.
•• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
4
Notice for this monitor
CONTENTS
Notice for this monitor.......................................... 3
Chapter 5
Troubleshooting............................... 34
Cleaning..................................................................... 4
5-1.
No Picture..................................................... 34
To use the monitor comfortably.............................. 4
5-2.
Imaging Problems........................................ 35
CONTENTS.............................................................. 5
5-3.
Other Problems............................................ 36
Chapter 1
1-1.
Introduction........................................ 6
Features.......................................................... 6
●●
Support for DisplayPort over USB Type-C
(DP Alt Mode) / USB Power Delivery................. 6
High Degree of Flexibility for Installation......... 7
Reduction of Power Consumption................... 7
Realizing More Convenient Operations
Using Screen InStyle....................................... 7
●●
●●
●●
1-2.
Controls and Functions................................ 8
●●Front................................................................. 8
●●Rear.................................................................. 9
1-3.
Supported Resolutions................................10
●●For DisplayPort...............................................10
●●For HDMI.........................................................11
●●For USB-C.......................................................12
1-4.
Changing the Computer Display Settings....13
●●Windows 10.....................................................13
●●Windows 8.1 / Windows 7...............................13
●●macOS............................................................13
Chapter 2
Basic Adjustment / Setting............. 14
2-1.
Switch Operation Method............................14
2-2.
Switching Input Signals...............................15
2-3.
Switching Display Modes (Color Modes)....18
2-4.
Conserving Energy.......................................19
2-5.
Adjusting Brightness...................................21
2-6.
Adjusting Volume.........................................21
●●PbyP display....................................................15
●●PinP display.....................................................17
Chapter 6
6-1.
Reference......................................... 37
Attaching the Optional Arm.........................37
●●Attaching the optional arm
(or optional stand).......................................... 38
Attaching the original stand........................... 38
●●
6-2.
Detaching/Attaching the Cable Holder...... 39
●●Detaching the cable holder............................ 39
●●Attaching the cable holder............................. 39
6-3.
Detaching / Attaching the Cable Cover..... 40
●●
●●
Attaching the cable cover............................... 40
Detaching the cable cover..............................41
6-4.
Connecting Multiple PCs............................ 42
6-5.
Using the USB Hub Function...................... 43
●●Connection examples.....................................42
●●Connection procedure................................... 43
6-6.
Specifications.............................................. 44
●●
Accessories.................................................... 45
Appendix............................................................... 46
Trademark................................................................ 46
License..................................................................... 46
ENERGY STAR......................................................... 46
FCC Declaration of Conformity..............................47
●●Display Modes.................................................18
Chapter 3
Advanced Adjustment / Setting..... 22
3-1.
Basic Operation of the Setting Menu........ 22
3-2.
Setting Menu Functions.............................. 23
●●Color Adjustment............................................ 23
●●Signal Settings............................................... 26
●●Preference Settings....................................... 28
●●Language....................................................... 29
●●Information..................................................... 30
Chapter 4
Administrator Settings.................... 31
4-1.
Basic Operation of the “Administrator
Settings” Menu..............................................31
4-2.
Functions of the “Administrator
Settings” Menu............................................. 32
CONTENTS
5
Chapter 1 Introduction
Thank you very much for choosing an EIZO color LCD monitor.
1-1. Features
for DisplayPort over USB Type-C (DP Alt Mode) / USB Power
●●Support
Delivery
This product is equipped with a USB Type-C (USB-C) connector compatible with DP Alt Mode and
USB Power Delivery.
•• While being used as an external monitor of a notebook PC, this product can supply power to the
PC.
Video Signals
Power Supply
•• While displaying photos and motion pictures from a smartphone or tablet, this product can charge
the device.
Video Signals
100%
Power Supply
Note
•• Devices to be connected must be equipped with a USB-C connector, and support the charging function
based on USB-C or USB Power Delivery.
•• The device connected to the monitor can be charged even when the monitor is in power saving mode.
•• Even when the monitor is turned off with the main power turned on, the connected device can be recharged.
In this case, the “Compatibility Mode” needs to be left “On”. For details about how to modify the settings,
please refer to “4-1. Basic Operation of the “Administrator Settings” Menu” (page 31).
6
Chapter 1 Introduction
●●High Degree of Flexibility for Installation
•• This product can be used as an external monitor of a notebook computer.
•• This product can be used in a multi-monitor configuration in which multiple monitors are connected
to a single PC.
●●Reduction of Power Consumption
This product provides a function that automatically adjusts the screen brightness to reduce power
consumption *1. Power Reduction, CO2 Reduction, and Eco Performance Level can be checked on
the "EcoView Settings" menu. (page 19)
•• Auto EcoView
The ambient light sensor on the front of the monitor detects the ambient brightness to automatically
adjust the screen brightness to a comfortable level.
•• EcoView Optimizer 2
The monitor automatically adjusts the screen brightness according to the white level of the input
signal. This function can reduce power consumption while maintaining the brightness specified by
the input signal.
*1 Reference values
Maximum power consumption: 163 W (when a USB device is connected and the speakers are working),
standard power consumption: 32 W (brightness 120 cd/m2, when no USB device is connected and the
speakers are not working, at default settings)
●●Realizing More Convenient Operations Using Screen InStyle
The "Screen InStyle" monitor control utility enables you to use the monitor more conveniently.
•• The monitor color mode can be switched automatically to suit the software to be used.
•• When multiple monitors are installed, you can turn the power on and off or change the color mode
of all monitors at the same time.
Note
•• Screen InStyle can be downloaded from our web site (http://www.eizoglobal.com).
•• The Windows operating systems are only supported.
Chapter 1 Introduction
7
1-2. Controls and Functions
●●Front
5
1
5
2
3
4
1. Ambient light sensor Detects ambient brightness. If you use Auto EcoView, the screen brightness is
automatically adjusted according to the ambient brightness (page 20).
2. Operation switches Displays menus. Operate the switches according to the operation guide (page 22).
3. Power switch
Turns the power on or off.
4. Power indicator
Indicates the monitor’s operation status.
White: Normal operation mode
Orange: Power saving mode
OFF: Main power / power off
5. Speakers
Outputs audio.
8
Chapter 1 Introduction
●●Rear
11
6
12
7
13
15
14
16
10
8
6.
7.
8.
9.
10.
9
Handle
Security lock slot
Main power switch
Power connector
Input signal connectors
This handle is used for transportation.
Complies with Kensington’s MicroSaver security system.
Turns the main power on or off. : On, : Off
Connects the power cord.
The following connectors are available on the monitor rear in order of left to
right.
HDMI connector (1)
HDMI connector (2)
DisplayPort connector
USB-C connector (USB upstream port)
Use this button to remove the monitor from the stand.
Connects to a peripheral USB device. (page 28)
11. Lock button
12. USB downstream port
(support for boost charging)
13. USB downstream port
Connects to a peripheral USB device.
14. Headphone jack
Connects to headphones.
15. Cable holder
Holds the monitor cables.
Adjusts the height and angle (tilt and swivel) of the monitor.
16. Stand*1
*1 An optional arm (or optional stand) can be attached by removing the stand section (see “6-1. Attaching the
Optional Arm” (page 37)).
Chapter 1 Introduction
9
1-3. Supported Resolutions
The monitor supports the following resolutions.
●●For DisplayPort
Resolution
Vertical scan
frequency (Hz)
Single screen and PinP
display *1
Version 1.2
Version 1.1
PbyP display
Dual screen
display
Quad screen
display
720 × 400
70.087
√
√
√
√
640 × 480
59.940
√
√
√
√
640 × 480
60.000
√
√
√
√
800 × 600
60.317
√
√
√
√
1024 × 768
60.004
√
√
√
√
1280 × 720
59.855
√
√
√
√
1280 × 720
59.979
√
√
√
√
1280 × 800
59.810
√
√
√
√
1280 × 800
59.910
√
√
√
√
1280 × 1024
60.020
√
√
√
√
1600 × 900
60.000
√
√
√
√
1600 × 1200
60.000
√
√
√
√
1680 × 1050
59.954
√
√
√
√
1680 × 1050
59.883
√
√
√
√
1920 × 1200
59.885
√
√
√
1920 × 1200
59.950
√
√
√
2560 × 1440
59.951
√
√
1280 × 1600
59.910
√
3840 × 2160
59.997
√ *2
3840 × 2160
29.981
√
√ *2
1920 × 2160
59.988
√ *2
1280 × 720
60.000
√
√
√
√
1280 × 720
59.940
√
√
√
√
1920 × 1080
60.000
√
√
√
√
1920 × 1080
59.940
√
√
√
√
1920 × 1080
30.000
√
√
√
√
1920 × 1080
29.970
√
√
√
√
720 × 480
60.000
√
√
√
√
720 × 480
59.940
√
√
√
√
720 × 480
60.000
√
√
√
√
720 × 480
59.940
√
√
√
√
*1 Supported signals differ depending on the settings in “Administrator Settings”. For information on how to
change the settings, see “4-2. Functions of the “Administrator Settings” Menu” (page 32).
*2 This is the recommended resolution.
10
Chapter 1 Introduction
●●For HDMI
Resolution
Vertical scan
frequency (Hz)
720 × 400
640 × 480
640 × 480
800 × 600
1024 × 768
1280 × 720
1280 × 720
1280 × 800
1280 × 800
1280 × 1024
1600 × 900
1600 × 1200
1680 × 1050
1680 × 1050
1920 × 1200
1920 × 1200
2560 × 1440
1280 × 1600
3840 × 2160
3840 × 2160
1920 × 2160
1920 × 2160
1280 × 720
1280 × 720
1280 × 720
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
720 × 480
720 × 480
720 × 480
720 × 480
720 × 576
720 × 576
3840 × 2160
3840 × 2160
3840 × 2160
3840 × 2160
3840 × 2160
70.087
59.940
60.000
60.317
60.004
59.855
59.979
59.810
59.910
60.020
60.000
60.000
59.954
59.883
59.885
59.950
59.951
59.910
59.997
29.981
59.988
29.952
60.000
59.940
50.000
60.000
59.940
50.000
30.000
29.970
60.000
59.940
60.000
59.940
50.000
50.000
60.000
59.940
50.000
30.000
29.970
Single screen and PinP
display *1
4K UHD 60Hz
4K UHD 30Hz
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√ *2
√ *2
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√ *2
√ *2
PbyP display
Dual screen
display
Quad screen
display
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√ *2
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
*1 Supported signals differ depending on the settings in “Administrator Settings”. For information on how to
change the settings, see “4-2. Functions of the “Administrator Settings” Menu” (page 32).
*2 This is the recommended resolution.
Chapter 1 Introduction
11
●●For USB-C
Resolution
Vertical scan
frequency (Hz)
Single screen and PinP
display *1
4K UHD 60Hz 4K UHD 30Hz
/ USB2.0
/ USB3.1
PbyP display
Dual screen
display
Quad screen
display
720 × 400
70.087
√
√
√
√
640 × 480
59.940
√
√
√
√
640 × 480
60.000
√
√
√
√
800 × 600
60.317
√
√
√
√
1024 × 768
60.004
√
√
√
√
1280 × 720
59.855
√
√
√
√
1280 × 720
59.979
√
√
√
√
1280 × 800
59.810
√
√
√
√
1280 × 800
59.910
√
√
√
√
1280 × 1024
60.020
√
√
√
√
1600 × 900
60.000
√
√
√
√
1600 × 1200
60.000
√
√
√
√
1680 × 1050
59.954
√
√
√
√
1680 × 1050
59.883
√
√
√
√
1920 × 1200
59.885
√
√
√
1920 × 1200
59.950
√
√
√
2560 × 1440
59.951
√
√
1280 × 1600
59.910
√
3840 × 2160
59.997
√ *2
3840 × 2160
29.981
√
√ *2
1920 × 2160
59.988
√ *2
1280 × 720
60.000
√
√
√
√
1280 × 720
59.940
√
√
√
√
1920 × 1080
60.000
√
√
√
√
1920 × 1080
59.940
√
√
√
√
1920 × 1080
30.000
√
√
√
√
1920 × 1080
29.970
√
√
√
√
720 × 480
60.000
√
√
√
√
720 × 480
59.940
√
√
√
√
720 × 480
60.000
√
√
√
√
720 × 480
59.940
√
√
√
√
*1 Supported signals differ depending on the settings in “Administrator Settings”. For information on how to
change the settings, see “4-2. Functions of the “Administrator Settings” Menu” (page 32).
*2 This is the recommended resolution.
Note
•• Only the progressive scan type is supported.
12
Chapter 1 Introduction
1-4. Changing the Computer Display Settings
If the image is not displayed properly after connecting the monitor to a PC, follow the procedure below to
change the display settings on the computer.
●●Windows 10
1. Right-click the mouse anywhere on the desktop except on icons. A menu is displayed.
2. From the displayed menu, click “Display Settings”. The “Settings” screen is displayed.
3. If multiple monitors, including notebook PC screens, are connected to the computer, select “Extend
these displays” in the “Multiple displays” menu, and then click “Keep changes” on the confirmation
screen. After changing the settings, select a monitor in the “Select and rearrange displays” menu.
4. Select the “Make this my main display” option in the “Multiple displays” menu. This enables the
monitor to display images properly.
5. Confirm that the recommended resolution for the monitor is set in the “Resolution” menu.
(“(Recommended)” is displayed after the resolution.)
6. To change the size of text and icons, select a magnification in the menu of zoom percentages
according to personal preference.
7. If a message prompting you to sign out is displayed after changing the settings, sign out and then
sign in again.
●●Windows 8.1 / Windows 7
* For Windows 8.1, click the "Desktop" tile on the Start Screen to display the desktop.
1. Right-click the mouse anywhere on the desktop except on icons. A menu is displayed.
2. From the displayed menu, click “Screen resolution”. The settings screen is displayed.
3. If multiple monitors, including notebook PC screens, are connected to the computer, select “Extend
these displays” in the “Multiple displays” menu, and then click “Apply”. Click “Keep changes” on
the confirmation screen.
4. Select a monitor in the “Display” menu, and then select the “Make this my main display” option
and click “Apply”. This enables the monitor to display images properly.
5. Confirm that the recommended resolution for the monitor is set in the “Resolution” menu.
(“(recommended)” is displayed after the resolution.)
6. To change the size of text and icons, click “Make text and other items larger or smaller”, select a
size according to personal preference on the settings screen, and then click “Apply”.
7. If a message prompting you to sign out/log off is displayed after changing the settings, sign out/
log off and then sign in/log in again.
●●macOS
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” panel is displayed, click “Displays”.
3. If multiple monitors, including notebook PC screens, are connected to the computer, make sure
that “Mirror Displays” is not selected on the “Arrangement” tab. If it is selected, remove the check
mark.
4. Select the “Display” tab, and make sure that “Default for display” is selected for “Resolution”. If
it is not selected, add a check mark. The correct resolution has now been set for your display.
Close the “System Preferences” panel. If multiple monitors, including notebook PC screens, are
connected to the computer, configure these settings in “Display” on each monitor.
5. To select a resolution according to personal preference, select “Scaled” and then select a
resolution (either from a list or icons), and then close the panel.
Chapter 1 Introduction
13
Chapter 2 Basic Adjustment / Setting
This product enables users to change the brightness according to personal preference or to suit the usage
environment and reduce power consumption to conserve energy.
This chapter describes the basic functions that can be adjusted and set using the switches on the front of the
monitor.
For advanced adjustment and setting procedures using the Setting menu, see “Chapter 3 Advanced
Adjustment / Setting” (page 22).
2-1. Switch Operation Method
1. Displaying the operation guide
1. Touch any switch (except
).
The operation guide appears on the screen.
2. Adjusting / setting
1. Touch a switch for adjustment / setting.
The Adjustment / Setting menu appears.
(A submenu may also be displayed. In this case, select the item for adjustment / setting using
select
.)
2. Perform adjustment / setting with the switches and select
3. Exiting
1. Select
14
to exit the menu.
Chapter 2 Basic Adjustment / Setting
to accept the changes.
and
2-2. Switching Input Signals
When a monitor has multiple signal inputs, the signal to display on-screen can be changed.
Note
•• "Screen InStyle" allows you to switch input signals using the shortcut keys on the keyboard.
●●PbyP display
By selecting PbyP (Picture by Picture) display when a monitor has multiple input signals, windows can
be displayed side-by-side (dual screen) or side-by-side and above-and-below (quad screen).
Because multiple windows can be displayed on a single monitor, the need for changing between
signals is eliminated, which leads to increased work efficiency.
By selecting PbyP display, the combination of signals to display on the left and right windows or quad
screen can be switched.
PbyP display image (dual screen)
A
B
PbyP display image (quad screen)
A
B
C
D
Chapter 2 Basic Adjustment / Setting
15
Function
PbyP
Settings
Input
Setting
Value
Description
Left
USB-C
DisplayPort
HDMI 1
HDMI 2
Select an input signal to be displayed on the left screen of
the PbyP display (dual screen).
Right
USB-C
DisplayPort
HDMI 1
HDMI 2
Select an input signal to be displayed on the right screen
of the PbyP display (dual screen).
Upper Left
USB-C
DisplayPort
HDMI 1
HDMI 2
Select an input signal to be displayed on the upper left
screen of the PbyP display (quad screen).
Lower Left
USB-C
DisplayPort
HDMI 1
HDMI 2
Select an input signal to be displayed on the lower left
screen of the PbyP display (quad screen).
Upper Right
USB-C
DisplayPort
HDMI 1
HDMI 2
Select an input signal to be displayed on the upper right
screen of the PbyP display (quad screen).
Lower Right
USB-C
DisplayPort
HDMI 1
HDMI 2
Select an input signal to be displayed on the lower right
screen of the PbyP display (quad screen).
Note
•• You cannot set the same input signal for multiple screens. Therefore, when changing the input signal for a
screen, if you select an input signal that has already been set for another screen, the signals are switched
automatically.
16
Chapter 2 Basic Adjustment / Setting
●●PinP display
By selecting PinP (Picture in Picture) display when a monitor has multiple input signals, a large
window and a small window can be displayed.
Because multiple windows can be displayed on a single monitor, the need for changing between
signals is eliminated, which leads to increased work efficiency.
By selecting PinP display, the combination of the signals to display on the large and small windows
can be switched.
PinP display image
Large window
A
Function
PinP
Settings
Setting
Value
B
Small window
Description
PinP Size
Large
Small
Select the size of the small window.
PinP Position
Upper Left
Lower Left
Upper Right
Lower Right
Select the position of the small window.
Input
Large Window USB-C
DisplayPort
HDMI 1
HDMI 2
Select the input signal for the large window.
Small Window USB-C
DisplayPort
HDMI 1
HDMI 2
Select the input signal for the small window.
Note
•• You cannot set the same input signal for the large and small windows. Therefore, when changing the input
signal for the large window, if you select the input signal that has already been set for the small window, the
input signals for the large and small windows are switched automatically.
Chapter 2 Basic Adjustment / Setting
17
2-3. Switching Display Modes (Color Modes)
This product is preinstalled with color modes for various display purposes.
By switching the mode according to the purpose and contents of the display, you can display images in
an appropriate manner.
●●Display Modes
Color Mode
User1
User2
sRGB
Purpose
Select either of these modes to set a user-defined display mode.
This mode is suitable for matching color reproduction with peripheral devices that
support sRGB, such as when printing photos taken using a digital camera.
Paper
This mode uses color tones and contrast similar to that of paper to produce a printed
paper effect. It is suitable for displaying images from media such as books and
documents.
Movie
This mode displays moving images brightly and with a clear-cut three-dimensional
appearance. It is suitable for playing back video content.
DICOM
Select this mode to simply display medical purpose digital images based on DICOM
Part 14.
Attention
•• This is not intended to be used for diagnostic purposes.
Note
•• "Screen InStyle" allows you to select the color mode automatically according to the software in use.
•• In Paper mode, the amount of blue light emitted from the screen is reduced by changing the color tone and
controlling the brightness.
18
Chapter 2 Basic Adjustment / Setting
2-4. Conserving Energy
This monitor is equipped with EcoView functions to enable users to conserve energy.
You can use this function to curtail unnecessary power consumption and save on electricity expenses.
Saving power also reduces carbon dioxide emissions.
Note
•• The power saving level (Power Reduction, CO2 Reduction, and Eco Performance Level) can be checked on the
“EcoView Settings” menu. The more indicators that light up representing the Eco Performance Level, the higher
the power saving level attained.
-- Power Reduction: the reduction in the backlight’s power consumption as a result of the adjusted brightness
value.
-- CO2 Reduction: converted from the “Power Reduction” value, this is an estimate of the quantity of CO2
emissions reduced when using the monitor for 1 hour.
•• The numeric value is a result of calculation based on a default setting (0.000555t-CO2 / kWh) determined by a
Japanese ministerial ordinance (2006, Ministry of Economy, Trade and Industry, Ministry of Environment, civil
code article 3) and may differ depending on country and year.
Chapter 2 Basic Adjustment / Setting
19
Function
Auto EcoView
Setting
Value
On
Off
Description
The ambient light sensor on the front of the monitor
detects the ambient brightness to automatically adjust
the screen brightness to a comfortable level using Auto
EcoView. The power consumption of the backlight can
be curtailed by adjusting the brightness to an appropriate
level.
This function can also mitigate eye strain and tiredness
caused by a screen that is too bright or too dark.
Note
•• Be careful not to block the ambient light sensor on the
lower side of the monitor when using Auto EcoView.
•• Even when the Auto EcoView setting is “On”, the
operation switch on the front of the monitor or color
adjustment can be used to change the “Brightness”
to suit your personal preference. Moreover, the
manner in which the Auto EcoView function changes
brightness also differs according to the changed
value.
•• When “DICOM” is selected for the color mode, the
Auto EcoView setting is turned “Off”.
EcoView Optimizer 2
On
Off
The monitor automatically adjusts the screen brightness
according to the white level of the input signal.
This function can reduce power consumption while
maintaining the brightness specified by the input signal.
Note
•• The setting is turned “Off” in the following cases:
--When “Movie” or “DICOM” is selected for the color
mode
--During PbyP/PinP display
•• When set to “On”, the appearance of pale colors may
change. If this bothers you, set this function to “Off”.
20
Chapter 2 Basic Adjustment / Setting
2-5. Adjusting Brightness
The brightness of the screen can be adjusted to suit the installation environment or personal preference.
The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD
back panel).
Setting Value
0 to 100
2-6. Adjusting Volume
The volume of the speakers and headphones can be set individually.
Setting Value
0 to 30
When the speakers are
connected
When the headphones are
connected
Chapter 2 Basic Adjustment / Setting
21
Chapter 3 Advanced Adjustment / Setting
This chapter describes the advanced monitor adjustment and setting procedures using the Setting menu.
For basic functions, see “Chapter 2 Basic Adjustment / Setting” (page 14).
3-1. Basic Operation of the Setting Menu
1. Menu display
1. Touch any switch (except
).
The operation guide appears.
2. Select
.
The Setting menu appears.
2. Adjusting / setting
1. Select a menu to adjust / set with
and select
.
and select
.
The Sub menu appears.
2. Select an item to adjust / set with
The Adjustment / Setting menu appears.
3. Perform adjustment / setting with
or
and select
to accept the changes.
The Sub menu appears.
Selecting
during adjustment / setting will cancel the adjustment / setting and restore the state prior to
making changes.
3. Exiting
1. Selecting
22
several times will terminate the Setting menu.
Chapter 3 Advanced Adjustment / Setting
3-2. Setting Menu Functions
●●Color Adjustment
The color mode setting status can be adjusted according to personal preference.
Functions that can be adjusted differ depending on the color mode.
Function
√: Adjustable -: Not adjustable
Color Mode
User1
User2
sRGB
Paper
Movie
DICOM
Brightness
√
√
√
√
-
Contrast
√
-
-
√
-
Temperature
√
-
√
√
-
Gamma
√
-
-
-
-
Super Resolution
√
-
√
√
-
Advanced Overdrive
Settings Hue
√
-
-
-
-
√
-
-
√
-
Saturation
√
-
-
√
-
Gain
√
-
-
-
-
√
√
√
√
-
Reset
Attention
•• It takes about 30 minutes for the monitor display to stabilize. Please wait 30 minutes or more after power to
the monitor has been turned on before adjusting the monitor.
•• The same image may be observed in different colors on multiple monitors due to monitor-specific
characteristics. Make fine color adjustments visually when matching colors across multiple monitors.
Chapter 3 Advanced Adjustment / Setting
23
Function
Color Mode
Brightness
Setting
Value
Description
User1
User2
sRGB
Paper
Movie
DICOM
Select the desired mode according to the monitor application.
The color setting status can also be adjusted according to personal
preference. Select the mode for adjustment and perform adjustment
using the relevant functions.
0 to 100
The screen brightness is adjusted by changing the brightness of the
backlight (light source from the LCD back panel).
Note
•• For details on the adjustment status of each mode, see “2-3.
Switching Display Modes (Color Modes)” (page 18).
Note
•• If the image is too dark even when the brightness is set to 100,
adjust the contrast.
Contrast
0 to 100
The brightness of the screen is adjusted by varying the video signal
level.
Note
•• A contrast of 50 displays every color gradation.
•• When adjusting the monitor, it is recommended to perform
brightness adjustment, which does not lose gradation
characteristics, prior to contrast adjustment.
•• Perform contrast adjustment in the following cases.
--If the image is too dark even when the brightness is set to 100
(Set the contrast to higher than 50.)
Temperature
Off
4000 K to
10000 K (in
increments of
500 K. 9300 K
is included.)
Adjust the color temperature.
The color temperature is normally used to express the hue of “White”
and/or “Black” with a numerical value. The value is expressed in
degrees “K” (Kelvin).
The screen becomes reddish at low color temperatures and bluish at
high color temperatures, similar to the temperatures of a flame. A gain
preset value is set for each color temperature setting value.
Note
•• The value shown in “K” is available only as a reference.
•• “Gain” allows you to perform more advanced adjustment.
•• If set to “Off”, the image is displayed in the preset color of the
monitor (Gain: 100 for each RGB channel).
•• When the gain is changed, the color temperature setting changes
to “Off”.
Gamma
1.8
2.0
2.2
2.4
Adjust the gamma.
While the brightness of the monitor varies depending on the input
signal, the variation rate is not proportional to the input signal.
Maintaining the balance between the input signal and brightness of
the monitor is referred to as “Gamma correction”.
Note
Super Resolution
24
Standard
Low
Off
Chapter 3 Advanced Adjustment / Setting
•• If "sRGB" is selected for the color mode, the gamma value is
fixed to "sRGB".
•• If “Paper” is selected for the color mode, “Paper” is displayed for
the gamma value.
•• If “DICOM” is selected for the color mode, “DICOM” is displayed
for the gamma value.
Image blur can be reduced by enhancing its outline.
Setting
Value
Function
Advanced Overdrive Enhanced
Settings
Standard
Off
Hue
-50 to 50
Description
This function allows you to set the overdrive intensity based on the
use of the monitor.
Image lag can be reduced by using the “Enhanced” setting when
displaying moving images.
Adjust the hue.
Note
•• Using this function may prevent some color gradations from being
able to be displayed.
Saturation -50 to 50
Adjust the color saturation.
Note
•• Using this function may prevent some color gradations from being
able to be displayed.
•• The minimum value (-50) changes the screen to monochrome.
Gain
0 to 100
The brightness of each red, green, and blue color component is
referred to as “Gain”. The hue of “white” can be changed by adjusting
the gain.
Note
Reset
-
•• Using this function may prevent some color gradations from being
able to be displayed.
•• The gain value changes according to the color temperature.
•• When the gain is changed, the color temperature setting changes
to “Off”.
Reset any color adjustments for the currently selected color mode
back to the default settings.
Chapter 3 Advanced Adjustment / Setting
25
●●Signal Settings
Set the details regarding input signal, such as the screen display size and color format.
Function
Window Selection
Setting Value
Left
Right
Upper Left
Lower Left
Upper Right
Lower Right
Large Window
Small Window
Description
Select the target for the signal settings.
When using PbyP/PinP display, select this target first.
•• “Left”
The setting is applied to the left screen in PbyP display (dual
screen).
•• “Right”
The setting is applied to the right screen in PbyP display
(dual screen).
•• “Upper Left”
The setting is applied to the upper left screen in PbyP
display (quad screen).
•• “Lower Left”
The setting is applied to the lower left screen in PbyP
display (quad screen).
•• “Upper Right”
The setting is applied to the upper right screen in PbyP
display (quad screen).
•• “Lower Right”
The setting is applied to the lower right screen in PbyP
display (quad screen).
•• “Large Window”
The setting is applied to the large window in PinP display.
•• “Small Window”
The setting is applied to the small window in PinP display.
Note
•• Enabled only during PbyP/PinP display.
•• For details on PbyP/PinP, see “2-2. Switching Input Signals”
(page 15).
26
Chapter 3 Advanced Adjustment / Setting
Function
Picture Expansion
Setting Value
Auto *1
Full Screen
Aspect Ratio
Dot by Dot
Description
The screen size of the monitor display can be changed.
•• “Auto”
The monitor automatically changes the screen size
according to the aspect ratio and resolution information
from the PC.
•• “Full Screen”
Images are stretched to full screen. Since aspect ratios are
not maintained, images may be distorted in some cases.
•• “Aspect Ratio”
Images are enlarged to full screen without changing the
aspect ratio. Since aspect ratios are maintained, blank
horizontal or vertical borders may appear.
•• “Dot by Dot”
Displays the image at the set resolution or size specified by
the input signal.
Note
•• Example settings
--Full Screen
--Aspect Ratio
--Dot by Dot
(input signal)
•• During PinP display, the aspect ratio of the small window is
fixed and therefore the display size of the window cannot
be changed.
Input Color Format
Input Range
Auto
YUV 4:2:2 *1
YUV 4:4:4 *1
YUV *2
RGB
The color format of the input signal can be specified.
Try changing this setting if colors are not displayed correctly.
Auto
Full
Limited
Depending on the PC, black and white of the video level of the
signal output to the monitor may be limited. If a limited signal is
displayed on the monitor, black will appear faint and white will
appear dull, leading to a reduction in contrast. The output range
of such signals can be extended to match the actual contrast
ratio of the monitor.
•• “Auto”
Automatically identifies the brightness range of the input
signal and displays the image accordingly.
•• “Full”
Extension of the signal output range is not performed.
•• “Limited”
Extends the signal output range through 0 to 255 and
displays the image.
Note
•• This setting is required when a DVI device is connected to
the monitor via the HDMI connector port using a DVI-HDMI
conversion connector.
*1 Only enabled during HDMI input
*2 Only enabled during DisplayPort input or USB-C input
Chapter 3 Advanced Adjustment / Setting
27
●●Preference Settings
The monitor’s settings can be configured to suit the usage environment or personal preference.
Function
Setting
Value
Description
USB CHARGE Normal
The
USB downstream port of the monitor supports boost charging via
Port
Charging Only USB 3.0. By changing this setting to “Charging Only”, the device connected
to the
port can be charged in a shorter period of time than that which
would be required when it is set to “Normal”.
Note
•• Before changing this setting, terminate communication between the
PC any USB devices connected to the monitor. All communication is
temporarily interrupted when the setting is changed.
•• The device connected to the
port must support boost charging.
•• When this is set to “Charging Only”, data communication cannot be
established between the device connected to the
port and the PC,
and the device will not operate.
•• When this is set to “Charging Only”, charging is possible even when the
monitor is not connected to the PC using a USB cable.
Power Save
On
Off
The monitor can be set to enter power saving mode according to the state of
the PC.
The monitor changes to power saving mode about 15 seconds after signal
input ceases to be detected.
When the monitor has shifted to power saving mode, images are not
displayed on the screen.
•• Exiting power saving mode
--If the monitor receives input, it automatically exits power saving mode
and returns to the normal display mode.
Note
Power Indicator On
Off
28
•• At the time of shifting to power saving mode, a message that indicates
the transition is displayed 5 seconds in advance.
•• During PbyP/PinP display, the monitor only enters the power saving
mode when signals are not input from all PCs.
•• When not using the monitor, you can turn off the main power supply or
disconnect the power plug so that the power is cut completely.
•• When the monitor is in power saving mode, devices connected to the
USB downstream port will still work. Therefore, power consumption of
the monitor varies with connected devices even in power saving mode.
The power indicator (white) can be turned off in normal operation mode.
Chapter 3 Advanced Adjustment / Setting
Setting
Value
Function
Sound
Selection
Description
Left
Select the source of audio to output from the monitor during PbyP/PinP
Right
display.
•• “Left”
Upper Left
Lower Left
Outputs the audio source from the left screen during PbyP display (dual
Upper Right
screen).
•• “Right”
Lower Right
Large Window
Outputs the audio source from the right screen during PbyP display (dual
Small Window
screen).
•• “Upper Left”
Outputs the audio source from the upper left screen during PbyP display
(quad screen).
•• “Lower Left”
Outputs the audio source from the lower left screen during PbyP display
(quad screen).
•• “Upper Right”
Outputs the audio source from the upper right screen during PbyP
display (quad screen).
•• “Lower Right”
Outputs the audio source from the lower right screen during PbyP display
(quad screen).
•• “Large Window”
Outputs the audio source from the large window during PinP display.
•• “Small Window”
Outputs the audio source from the small window during PinP display.
Note
Monitor Reset
-
•• Enabled only during PbyP/PinP display.
•• For details on PbyP/PinP, see “2-2. Switching Input Signals” (page 15).
Restore all settings to their default values except for the following settings.
•• PbyP/PinP Picture Setup
•• Settings on the “Administrator Settings” menu
●●Language
The display language for menus and messages can be selected.
Setting Value
English, German, French, Spanish, Italian, Swedish, Japanese, Simplified Chinese, Traditional
Chinese
Attention
•• The display language of the “Administrator Settings” menu cannot be changed.
Chapter 3 Advanced Adjustment / Setting
29
●●Information
Monitor information (product name, serial number, usage time, resolution, and input signal) can be
checked.
Example: •• Single screen display
•• Dual PbyP/PinP display
30
Chapter 3 Advanced Adjustment / Setting
•• Quad PbyP display
Chapter 4 Administrator Settings
This chapter describes how to configure monitor operation using the “Administrator Settings” menu.
This menu is for administrators. Configuration on this menu is not required for normal monitor use.
4-1. Basic Operation of the “Administrator Settings”
Menu
1. Menu display
1. Touch
to turn off the monitor.
2. While touching the leftmost switch, touch
for more than 2 seconds to turn on the monitor.
The “Administrator Settings” menu appears.
2. Setting
1. Select an item to set with
and select
.
The Adjustment / Setting menu appears.
2. Set with
and select
.
The “Administrator Settings” menu appears.
3. Applying and exiting
1. Select “Apply” and then
.
The settings are applied and the “Administrator Settings” menu exits.
Attention
•• The language (English) of the “Administrator Settings” menu cannot be changed.
Chapter 4 Administrator Settings
31
4-2. Functions of the “Administrator Settings” Menu
Function
Setting Value
Auto Input Detection On
Off
Description
This function automatically recognizes the connector through
which PC signals are input, and displays images on the
screen accordingly.
•• “On”
When the monitor is connected to multiple PCs, if a
specific PC enters power saving mode or no signals
are input to the monitor, the connector is automatically
changed to another one to which signals are input.
•• “Off”
This function displays the signal from the selected
connector regardless of whether a signal is input or not.
In this case, you can select the input signal to display
using the
operation switch on the front of the monitor.
For details, see “2-2. Switching Input Signals” (page
15).
Note
Compatibility Mode
USB-C
DisplayPort
32
•• This function is not available during PbyP/PinP display.
•• This product automatically recognizes the connector
through which PC signals are input, and displays images
on the screen accordingly regardless of whether this
function is set to On or Off just after the main power
switch on the rear side of the monitor has been turned
on.
•• When this function is set to “On”, the monitor only enters
the power saving mode when signals are not input from
any PC.
On
If you want to avoid the following phenomena, set this function
Off
to "On".
•• The positions of windows and icons are shifted when the
monitor is turned off / on or has returned from the power
saving mode.
•• Power Save function of the PC does not work normally.
•• During USB-C input, the screen blinks two or three times
immediately after the USB cable has been connected or
the PC has returned from the Power Save mode.
•• When the power to the monitor is turned off, a device
connected to the USB downstream port does not work.
•• When the monitor is turned off, a device connected via a
USB-C connector cannot be recharged.
4K UHD 60Hz / USB2.0 The USB setting and the types of signals that the monitor can
4K UHD 30Hz / USB3.1 display can be changed.
Version 1.1
The types of signals that the monitor can display can be
Version 1.2
changed.
Chapter 4 Administrator Settings
Function
HDMI 1
Setting Value
4K UHD 60Hz
4K UHD 30Hz
Description
The types of signals that the monitor can display can be
changed.
Note
•• If the HDMI signal that is being input is not displayed,
change this setting.
HDMI 2
4K UHD 60Hz
4K UHD 30Hz
The types of signals that the monitor can display can be
changed.
Note
On-Screen Logo
On
Off
Key Lock
Off
Menu
All
•• If the HDMI signal that is being input is not displayed,
change this setting.
When the monitor is turned on, the EIZO logo appears on the
screen.
When this function is set to “Off”, the EIZO logo does not
appear.
In order to prevent changes to settings, the operation
switches on the front of the monitor can be locked.
•• “Off” (default setting)
Enables all switches.
•• “Menu”
Locks the
switch.
•• “All”
Locks all switches except the power switch.
Chapter 4 Administrator Settings
33
Chapter 5 Troubleshooting
5-1. No Picture
Problem
1. No picture
•• Power indicator does not light up.
•• Power indicator is lighting white.
•• Power indicator is lighting orange.
•• Power indicator is flashing orange
and white.
2. The message below appears.
34
Possible cause and remedy
••
••
••
••
Check whether the power cord is connected properly.
Turn on the main power switch on the rear side of the monitor.
Touch .
Turn off the main power switch on the rear side of the monitor, and
then turn it on again a few minutes later.
•• Increase “Brightness”, “Contrast”, or “Gain” in the Setting menu (see
“Color Adjustment” (page 23)).
•• Switch the input signal.
•• Turn the setting “On” for “Compatibility Mode” on the “Administrator
Settings” menu (see “Compatibility Mode” (page 32)).
•• Move the mouse or press any key on the keyboard.
•• Check whether the PC is turned on.
•• Turn off the main power switch on the rear side of the monitor, and
then turn it on again.
•• This symptom may occur during DisplayPort input.
--Use a signal cable recommended by us for the connection. Turn
the monitor off and on.
•• This symptom may occur during USB-C input.
--Disconnect and connect the USB cable that is plugged in to the
upstream port (USB-C).
--Turn off the main power switch on the rear side of the monitor, and
then turn it on again.
This message appears when the signal is not input correctly even
though the monitor is functioning properly.
•• This message appears when no
signal is input.
Example:
•• The message shown left may appear, because some PCs do not
output the signal immediately after power-on.
•• Check whether the PC is turned on.
•• Check whether the signal cable is connected properly.
•• Switch the input signal.
•• Turn off the main power switch on the rear side of the monitor, and
then turn it on again.
•• The message shows that the
input signal is out of the specified
frequency range.
Example:
•• Check whether the PC is configured to meet the resolution and
vertical scan frequency requirements of the monitor (see “1-3.
Supported Resolutions” (page 10)).
•• Reboot the PC.
•• Select an appropriate setting using the graphics board’s utility. Refer
to the User’s Manual of the graphics board for details.
•• This message shows that a device
that is not compatible with DP Alt
Mode is connected to the USB-C
connector.
Example:
•• Check whether a signal cable recommended by us is used.
•• Check whether the connected device is compatible with DP Alt
Mode. Contact the device manufacturer for information about
compatibility with DP Alt Mode.
•• Please connect it via a DisplayPort cable or HDMI cable.
Chapter 5 Troubleshooting
5-2. Imaging Problems
Problem
1. The screen is too bright or too
dark.
2. Brightness cannot be changed or
it changes on its own.
3. Text is blurred.
4. Afterimages appear.
5. Green / red / blue / white / dark
dots remain on the screen.
6. Interference patterns or pressure
marks remain on the screen.
7. Noise appears on the screen.
8. The positions of windows and
icons are shifted when the
monitor is turned off / on or when
restored from power saving mode.
9. The color shown on the screen is
not correct.
10. Images are not displayed over the
entire area of the screen.
Possible cause and remedy
•• Use “Brightness” or “Contrast” in the Setting menu to adjust it (see
“Color Adjustment” (page 23)). (The LCD monitor backlight has
a limited life span. If the screen becomes dark or begins to flicker,
contact your local EIZO representative.)
•• If the screen is too bright, try changing the Auto EcoView setting
to “On”. The monitor detects the ambient brightness to adjust the
screen brightness automatically (see “Auto EcoView” (page 20)).
•• Try changing the Auto EcoView setting to “Off” (see “Auto EcoView”
(page 20)).
•• Check whether the PC is configured to meet the resolution and
vertical scan frequency requirements of the monitor (see “1-3.
Supported Resolutions” (page 10)).
•• Afterimages are particular to LCD monitors. Avoid displaying the
same image for a long time.
•• Use the screen saver or power saving function to avoid displaying
the same image for extended periods of time. Depending on the
image, an afterimage may appear even if it was displayed for a short
period of time. To remove such a phenomenon, change the image
or keep the power turned off for several hours.
•• This is due to LCD panel characteristics and not a malfunction.
•• Leave the monitor with a white or black screen. The symptom may
disappear.
•• In the Setting menu, set “Overdrive” to “Off” (see “Overdrive” (page
25)).
•• When inputting HDCP system signals, normal images may not be
displayed immediately.
•• Turn the setting “On” for “Compatibility Mode” on the “Administrator
Settings” menu (see “Compatibility Mode” (page 32)).
•• Try changing “Input Color Format” in the Setting menu (see “Input
Color Format” (page 27)).
•• Try changing “Picture Expansion” in the Setting menu (see “Picture
Expansion” (page 27)).
Chapter 5 Troubleshooting
35
5-3. Other Problems
Problem
1. The Setting menu does not
appear.
2. Cannot select items in the
Settings menu.
•• Check whether the switch operation lock function is active (see “Key
Lock” (page 33)).
•• Items that are displayed with gray text cannot be changed.
3. No audio output.
•• Check whether volume is set to 0.
•• Check the PC and audio playback software to see whether they are
configured correctly.
•• Check the “Sound Selection” setting during PbyP/PinP display (see
“Sound Selection” (page 29)).
•• Check whether the USB cable is correctly connected between the
PC and the monitor (see “6-5. Using the USB Hub Function” (page
43)).
•• Check whether the USB CHARGE port is set correctly (see “USB
CHARGE Port” (page 28)).
•• Check whether the USB cable is correctly connected between the
peripheral and the monitor.
•• Try using a different USB port on the monitor.
•• Try using a different USB port on the PC.
•• Reboot the PC.
•• If the peripheral devices work correctly when they are directly
connected to the PC, contact your local EIZO representative.
•• Depending on the USB 3.1 host controller that you are using,
connected USB devices may not be recognized correctly. Update to
the latest USB 3.1 driver provided by each manufacturer, or connect
the monitor to the USB 2.0 port.
•• Check the PC’s BIOS setting for USB when using Windows. (Refer
to the manual of the PC for details.)
•• This symptom may occur when the PC is connected to the
DisplayPort connector. Use a signal cable recommended by us for
the connection. Turn the monitor off and on.
•• Check the connection and condition of the USB devices connected
to the monitor.
•• Turn off the main power switch on the rear side of the monitor, and
then turn it on again.
•• Turn the setting “On” for “Compatibility Mode” on the “Administrator
Settings” menu (see “Compatibility Mode” (page 32)).
4. USB devices connected to the
monitor do not work.
5. Power indicator is flashing orange
and white.
6. Power Save function of the PC
does not work normally.
36
Possible cause and remedy
Chapter 5 Troubleshooting
Chapter 6 Reference
6-1. Attaching the Optional Arm
An optional arm (or an optional stand) can be attached by removing the stand section. Please refer to our
web site for the supported optional arm (or optional stand). http://www.eizoglobal.com
Attention
•• When attaching an arm or stand, follow the instructions of the respective User’s Manual.
•• When using another manufacturer’s arm or stand, confirm the following in advance and select one conforming to
the VESA standard. Use the VESA mounting screws supplied with this product when attaching the arm or stand.
-- Clearance between screw holes: 100 mm × 100 mm
-- VESA mount of the arm or stand, external dimensions: 122 mm x 122 mm or less
-- Plate thickness: 2.6 mm
-- Strong enough to support weight of the monitor unit (excluding the stand) and attachments such as cables.
•• When attaching an arm or stand, the installable orientations and movement range (tilt angle) are as follows:
Orientation
Movement range
(tilt angle)
Up: 45˚
Down: 45˚
•• Connect the cables after attaching an arm or stand.
•• Do not move the removed stand up and down. Doing so may result in injury or device damage.
•• The monitor, arm, and stand are heavy. Dropping them may result in injury or equipment damage.
Chapter 6 Reference
37
●●Attaching the optional arm (or optional stand)
1. Lay the LCD monitor on a soft cloth spread over a stable and flat surface with the panel surface
facing down.
2. Remove the stand.
As shown in the figure, while holding down the lock button (1), slide the stand toward the stand base until it
touches the stand base (2). Then, lift the stand up (3).
(3)
(1)
(2)
3. Attach the arm or stand to the monitor.
Use the VESA mounting screws supplied with this product when attaching the arm or stand.
●●Attaching the original stand
1. Lay the LCD monitor on a soft cloth spread over a stable and flat surface with the panel surface
facing down.
2. Remove the fixing screws on the optional arm (or optional stand), and detach the optional arm (or
optional stand).
3. Attach the original stand.
Insert the four tabs on the stand into the four holes on the back panel (1), and slide the stand towards the
upper portion of the monitor (2). The stand clicks when it is attached correctly.
(1)
Click!
38
Chapter 6 Reference
(2)
6-2. Detaching/Attaching the Cable Holder
●●Detaching the cable holder
1. Slide the cable holder to the left, and detach it from the stand.
●●Attaching the cable holder
1. Align the tabs of the cable holder with the attachment parts of the stand.
2. Slide the cable holder to the right, and attach it to the stand.
Chapter 6 Reference
39
6-3. Detaching / Attaching the Cable Cover
●●Attaching the cable cover
A
B
1. Align the tabs of (A) with the attachment parts of the stand.
A
2. Slide (A) downward to secure the tabs to the attachment parts of the stand.
3. Check the tabs of (B) (four locations indicated by
A
40
Chapter 6 Reference
) and the attachment locations of (A).
B
4. Pass the cables between (A) and (B), and align (B) with (A) to fit in.
5. Slide (B) downward and secure it to (A).
●●Detaching the cable cover
1. Slide (B) upward, and detach it from (A).
2. While holding down
of (A) lightly, slide (A) upward to detach it from the stand.
Chapter 6 Reference
41
6-4. Connecting Multiple PCs
This product can be connected to multiple PCs and allows you to switch between the connections for
display.
●●Connection examples
HDMI
HH200PR (HDMI - HDMI)
HDMI
(supplied)
DisplayPort
PP200 (DisplayPort - DisplayPort)
DisplayPort
(supplied)
USB-C
CC200SS (USB-C - USB-C)
USB-C
(supplied)
Note
•• You can select the input signal to display using the
operation switch on the front of the monitor. For details, see
“2-2. Switching Input Signals” (page 15).
•• This product provides a function that automatically recognizes the connector through which PC signals are input,
and displays images on the screen accordingly. For details, see “Auto Input Detection” (page 32).
42
Chapter 6 Reference
6-5. Using the USB Hub Function
This monitor is equipped with a USB hub. It functions as a USB hub when connected to a USBcompatible PC, allowing the connection of peripheral USB devices.
●●Connection procedure
1. Connect the USB cable between the USB-C connectors of the PC and the monitor.
2. Connect a peripheral USB device to the USB downstream port of the monitor.
Attention
•• If your PC is not equipped with a USB-C connector, a USB-C to Type-A conversion cable is required. Connect the
conversion cable between the USB downstream port of the PC and the USB-C connector of the monitor.
•• When you change the setting of “Compatibility Mode” (page 32), remove any peripherals such as a USB
memory device connected to the downstream port of the monitor.
•• When the main power of the monitor is off, a device connected to the USB downstream port will not operate.
•• When “Compatibility Mode” (page 32) is set to "Off" and the power to the monitor is turned off, a device
connected to the USB downstream port will not work.
Note
•• This product supports USB 3.1*1. When connecting to peripheral devices that support USB 3.1, high-speed data
communication is possible (however, only when the USB cable used to connect the PC and peripheral device is
USB 3.1 compliant and “USB-C” in the “Administrator Settings” menu is set to “4K UHD 30Hz / USB3.1”) (page
32).
*1 Only Gen1 5 Gbps is supported.
Chapter 6 Reference
43
6-6. Specifications
LCD Panel
Type
Backlight
Size
IPS (Anti-Glare)
LED
80.0 cm (31.5 inch)
Resolution
3840 dots x 2160 lines
Display Size (H × V)
697.3 mm × 392.2 mm
Pixel Pitch
0.182 mm
Display Colors
8-bit colors:
16.77 million colors
Viewing Angle
178˚ / 178˚
(H / V, typical)
Response Time (typical) Gray-to-gray:
Video Signals
Input Terminals
Digital Scanning
Frequency
(H / V)
14 ms (overdrive setting: Off)
5 ms (overdrive setting: Enhanced)
DisplayPort (HDCP) × 1, HDMI (HDCP)*1 × 2, USB-C (HDCP) × 1
DisplayPort:
HDMI:
USB-C (DP Alt Mode):
USB
Audio
Frame Synchronization
Mode
59.5 Hz to 60.5 Hz
Max. Dot Clock
DisplayPort:
540 MHz
HDMI:
600 MHz
USB-C (DP Alt Mode):
540 MHz
Port
Standard
Upstream port (USB-C) x 1
Downstream port (USB Type-A) x 2 (The
port supports boost
charging)
USB Specification Revision 3.1*2, Battery Charging Revision 1.2
Communication Speed
5 Gbps (super), 480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low)
Supply Current
Downstream
(USB Type-A):
Downstream
(USB Type-A,
port):
Upstream (USB-C):
Max. 900 mA
DisplayPort:
2ch linear PCM (32 kHz / 44.1 kHz /
48 kHz / 88.2 kHz / 96 kHz / 176.4 kHz /
192 kHz)
2ch linear PCM (32 kHz / 44.1 kHz /
48 kHz / 88.2 kHz / 96 kHz / 176.4 kHz /
192 kHz)
2ch linear PCM (32 kHz / 44.1 kHz /
48 kHz/ 88.2 kHz / 96 kHz / 176.4 kHz /
192 kHz)
Audio Input Format
USB-C (DP Alt Mode):
HDMI:
44
31 kHz to 134 kHz /
29 Hz to 31 Hz, 59 Hz to 61 Hz,
69 Hz to 71 Hz (at 720 × 400)
31 kHz to 135 kHz /
29 Hz to 31 Hz, 49 Hz to 61 Hz,
69 Hz to 71 Hz (at 720 × 400)
31 kHz to 134 kHz /
29 Hz to 31 Hz, 59 Hz to 61 Hz,
69 Hz to 71 Hz (at 720 × 400)
Max. 1.5 A (Normal)
Max. 2.1 A (Charging only)
Max. 60 W
Speakers
1 W + +1 W
Headphones
2 mW + +2 mW (32 Ω)
Input Terminals
DisplayPort × 1, HDMI × 2, USB-C × 1 (each shared with video signal)
Output Terminals
Stereo mini jack × 1
Chapter 6 Reference
Power
Physical
Specifications
Input
100 - 240 VAC ±10 %, 50 / 60 Hz 1.65 A - 0.75 A
Maximum Power
Consumption
Power Save Mode
163 W or less
0.5 W or less (no USB device connected, default settings)
Standby Mode
0.5 W or less (no USB device connected, default settings)
Dimensions
717.4 mm × 396.1 mm to 591.1 mm × 253.4 mm to 287.8 mm
(W × H × D) (Tilt: 35˚)
717.4 mm × 427.3 mm to 576.2 mm × 230 mm
(W × H × D) (Tilt: 0˚)
717.4 mm × 416.3 mm × 51.5 mm (W × H × D)
Dimensions
(Without Stand)
Net Weight
Operating
Environmental
Requirements
Approx. 11 kg
Net Weight (Without
Stand)
Height Adjustment
Range
Tilt
Approx. 7.6 kg
Swivel
344˚
Temperature
5 ˚C to 35 ˚C
Humidity
20 % to 80 % R.H. (no condensation)
Air Pressure
540 hPa to 1060 hPa
195 mm (Tilt: 35˚) / 148.9 mm (Tilt: 0˚)
Up 35˚, down 5˚
-20 ˚C to 60 ˚C
Transportation / Temperature
Storage
Humidity
10 % to 90 % R.H. (no condensation)
Environmental Air Pressure
200 hPa to 1060 hPa
Requirements
*1 HDMI CEC (or mutual control) is not supported.
*2 Only Gen1 5 Gbps is supported.
●●Accessories
For the latest information about accessories, refer to our web site. http://www.eizoglobal.com
Chapter 6 Reference
45
Appendix
Trademark
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing, LLC in the United States and other countries.
The DisplayPort Compliance Logo and VESA are registered trademarks of the Video Electronics
Standards Association.
The SuperSpeed USB Trident Logo is a registered trademark of USB Implementers
Forum, Inc.
The USB Power Delivery Trident logos are trademarks of USB Implementers Forum, Inc.
DICOM is the registered trademark of the National Electrical Manufacturers Association for its standards
publications relating to digital communications of medical information.
Kensington and Microsaver are registered trademarks of ACCO Brands Corporation.
Thunderbolt is a trademark of Intel Corporation in the United States and/or other countries.
Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and
other countries.
Adobe is a registered trademark of Adobe Systems Incorporated in the United States and other
countries.
Apple, macOS, Mac OS, OS X, Macintosh and ColorSync are registered trademarks of Apple Inc.
EIZO, the EIZO Logo, ColorEdge, CuratOR, DuraVision, FlexScan, FORIS, RadiCS, RadiForce,
RadiNET, Raptor and ScreenManager are registered trademarks of EIZO Corporation in Japan and other
countries.
ColorEdge Tablet Controller, ColorNavigator, EcoView NET, EIZO EasyPIX, EIZO Monitor Configurator,
EIZO ScreenSlicer, G-Ignition, i•Sound, Quick Color Match, RadiLight, Re/Vue, Screen Administrator,
Screen InStyle and UniColor Pro are trademarks of EIZO Corporation.
All other company and product names are trademarks or registered trademarks of their respective
owners.
License
The bitmap font used for this product is designed by Ricoh Industrial Solutions Inc.
ENERGY STAR
As an ENERGY STAR Partner, EIZO Corporation has determined that this product meets
the ENERGY STAR guidelines for energy efficiency.
46
Appendix
FCC Declaration of Conformity
For U.S.A., Canada Only
FCC Declaration of Conformity
We, the Responsible Party
EIZO Inc.
5710 Warland Drive, Cypress, CA 90630
Phone: (562) 431-5011
declare that the product
Trade name: EIZO
Model: FlexScan EV3285
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures.
*
*
*
*
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Note
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep interference
within the limits of a Class B digital device.
--AC Cord
--Shielded Signal Cable (enclosed)
Canadian Notice
This Class B information technology equipment complies with Canadian ICES-003.
Cet équipement informatique de classe B est conforme à la norme NMB-003 du Canada.
Appendix
47
03V27413B1
UM-EV3285
Copyright © 2018 EIZO Corporation. All rights reserved.
2nd Edition-October, 2018
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising