Eizo | S1703-A | User manual | Eizo S1703-A User Manual

Eizo S1703-A User Manual
User’s Manual
Color LCD Monitor
Important
Please read this “User’s Manual”, and “PRECAUTIONS” (separate
volume) carefully to familiarize yourself with safe and effective usage.
••Refer to the “Setup Guide” for information on the installation /
connection of the monitor.
••For the latest product information including the “User’s Manual”,
refer to our web site :
http://www.eizoglobal.com
Location of Caution Statement
The equipment must be connected to a grounded main outlet.
L’appareil doit être relié à une prise avec terre.
Jordet stikkontakt skal benyttes når apparatet tilkobles datanett.
Apparaten skall anslutas till jordat nätuttag.
電源コードのアースは必ず接地してください。
This product has been adjusted specifically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specifications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information confidential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specifications are subject to change without notice.
2

Notice for this monitor
This product is suited to general purposes like creating documents, viewing multimedia content (Assuming
usage of approximately 12 hours per day).
If using this product for the following kinds of applications, where an extremely high degree of reliability and
safety is required, then measures should be in place to maintain safety while using this product.
•• Transportation equipment (ships, aircraft, trains, and automobiles)
•• Safety devices (Disaster prevention systems, security control systems, etc.)
•• Life-critical devices (medical devices, such as life-support devices and operating room devices)
•• Nuclear energy control devices (Nuclear energy control systems, security control systems of nuclear facilities, etc.)
•• Major system communication devices (operation control systems of transportation systems, air traffic control systems, etc.)
This product has been adjusted specifically for use in the region to which it was originally shipped. If the
product is used outside the region, it may not operate as specified in the specifications.
This product may not be covered by warranty for uses other than those described in this manual.
The specifications noted in this manual are only applicable when the following are used:
•• Power cords provided with the product
•• Signal cables specified by us
Only use optional products manufactured or specified by us with this product.
If you place this product on a lacquer-coated desk, the color may adhere to the bottom of the stand due to
the composition of the rubber. Check the desk surface before use.
It takes about 30 minutes (under our measurement conditions) for the monitor display to stabilize. Please
wait 30 minutes or more after the monitor power has been turned on, and then adjust the monitor.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and
maintain a stable display.
When the screen image is changed after displaying the same image for extended periods of time, an
afterimage may appear. Use the screen saver or power save function to avoid displaying the same image for
extended periods of time. Depending on the image, an afterimage may appear even if it was displayed for
a short period of time. To remove such a phenomenon, change the image or keep the power turned off for
several hours.
If the monitor displays continuously over a long period of time, dark smudges or burn-in may appear. To
maximize the life of the monitor, we recommend the monitor be turned off periodically.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer
to “Cleaning” (page 4)).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may
appear on the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994 % or higher.
The backlight of the LCD panel has a fixed lifetime. Depending on the usage pattern, such as usage for
long continuous periods, the lifespan of the backlight may run out sooner, requiring replacement. When the
screen becomes dark or begins to flicker, please contact your local EIZO representative.
Do not press on the LCD panel or edge of the frame strongly, as this may result in display malfunctions, such
as interference patterns, etc. If pressure is continuously applied to the LCD panel surface, the liquid crystal
may deteriorate or the LCD panel may be damaged. (If the pressure marks remain on the panel, leave the
monitor with a black or white screen. The symptom may disappear.)
Do not scratch or press on the LCD panel with any sharp objects, at this may result in damage to the LCD
panel. Do not attempt to brush with tissues as this may scratch the panel.
Notice for this monitor
3
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew
condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the
monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage to the
monitor.
Cleaning
The stains on the cabinet and LCD panel surface can be removed by moistening part of a soft cloth with water.
Attention
•• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet
or LCD panel, and also quality deterioration of the image.
•• Never use thinner, benzine, wax, or abrasive cleaner as they may damage the cabinet or LCD panel surface.
Note
•• It is recommended that ScreenCleaner (available as an option) be used to clean the cabinet and LCD panel surface.
To use the monitor comfortably
•• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor
according to the environmental conditions.
•• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
4
Notice for this monitor
CONTENTS
Notice for this monitor.......................................... 3
Chapter 6
Reference......................................... 28
Cleaning..................................................................... 4
6-1.
Attaching the Optional Arm........................ 28
To use the monitor comfortably.............................. 4
6-2.
Connecting Multiple PCs............................ 29
CONTENTS.............................................................. 5
6-3.
Specifications.............................................. 30
Chapter 1
1-1.
Introduction........................................ 6
Controls and Functions................................ 6
●●Front................................................................. 6
●●Rear.................................................................. 7
1-2.
Supported Resolutions................................. 8
1-3.
Setting the Resolution.................................. 9
●●Analog Signal (D-Sub) Input............................ 8
●●Digital Signal (DVI-D) Input.............................. 8
●●Accessories.....................................................31
Appendix............................................................... 32
Trademark................................................................ 32
License..................................................................... 32
FCC Declaration of Conformity............................. 33
●●Windows 10...................................................... 9
●●Windows 8.1 / Windows 7................................ 9
●●OS X Mountain Lion (10.8) or later................... 9
●●Mac OS X 10.7................................................. 9
Chapter 2
Basic Adjustment/Setting............... 10
2-1.
Switch Operation Method............................10
2-2.
Switching Input Signals...............................11
2-3.
Switching Display Modes (Color Modes)....11
2-4.
Conserving Energy.......................................11
2-5.
Adjusting Brightness...................................13
2-6.
Adjusting Volume.........................................13
●●Display Modes.................................................11
Chapter 3
3-1.
3-2.
Advanced Adjustment/Setting....... 14
Basic Operation of the Setting Menu.........14
Setting Menu Functions...............................15
●●
●●
●●
●●
●●
Color Adjustment.............................................15
Signal Settings................................................18
Preference Settings....................................... 20
Language........................................................21
Information......................................................21
Chapter 4
Administrator Settings.................... 22
4-1.
Basic Operation of the “Administrator
Settings” Menu............................................. 22
4-2.
Functions of the “Administrator
Settings” Menu............................................. 23
Chapter 5
Troubleshooting............................... 24
5-1.
No Picture..................................................... 24
5-2.
Imaging Problems (For Both Digital and
Analog).......................................................... 25
5-3.
Imaging Problems (For Analog Only)........ 26
5-4.
Other Problems............................................ 27
CONTENTS
5
Chapter 1 Introduction
Thank you very much for choosing an EIZO color LCD monitor.
This chapter provides the names of the components and the resolution of the monitor.
1-1. Controls and Functions
●●Front
Tilt stand
1
1.
2.
3.
4.
6
Height adjustable stand
2
Ambient light sensor
Operation switches
Power switch
Power indicator
Chapter 1
Introduction
3
4
1
2
3
4
Detects ambient brightness (Auto EcoView function (page 12)).
Displays menus. Operate the switches according to the operation guide (page 14).
Turns the power on or off.
Indicates the monitor’s operation status.
White: Screen display
Orange: Power saving mode
OFF: Power off
●●Rear
Tilt stand
5
8
Height adjustable stand
6
7
9
5
8
12
10
11
5. Power connector
6. Input signal connectors
7. Analog audio input
connector
8. Speakers
9. Security lock slot
10. Stand*1
8
6
7
9
8
12
10
11
Connects the power cord.
Left: DVI-D connector / Right: D-Sub mini 15-pin connector
Outputs external audio from the monitor.
Outputs audio.
Complies with Kensington’s MicroSaver security system.
Tilt stand: Used to adjust the angle (tilt) of the monitor screen.
Height adjustable stand: Adjusts the height and angle (tilt, swivel, and rotation)
of the monitor.
11. Cable holder
Holds the monitor cables.
12. Headphone jack
Connects to headphones.
*1 An optional arm (or optional stand) can be attached by removing the stand section (see "6-1. Attaching the
Optional Arm" (page 28)).
Chapter 1
Introduction
7
1-2. Supported Resolutions
The monitor supports the following resolutions.
●●Analog Signal (D-Sub) Input
Resolution
Applicable Signal
Vertical Scan
Frequency
640 x 480
VGA
60Hz
720 x 400
VGA TEXT
70Hz
800 x 600
VESA
Up to 60Hz
1024 x 768
VESA
60Hz
1280 x 800
VESA
60Hz
1280 x 960
VESA
60Hz
1280 x 1024*1
VESA
60Hz
Dot Clock
108MHz
(Max.)
●●Digital Signal (DVI-D) Input
Resolution
Applicable Signal
Vertical Scan
Frequency
640 x 480
VGA
60Hz
720 x 400
VGA TEXT
70Hz
800 x 600
VESA
60Hz
1024 x 768
VESA
60Hz
1280 x 800
VESA
60Hz
1280 x 960
VESA
60Hz
1280 x 1024*1
VESA
60Hz
*1 Recommended resolution
8
Chapter 1
Introduction
Dot Clock
108MHz
(Max.)
1-3. Setting the Resolution
If the resolution is incorrect after connecting the monitor to a PC or if you want to change the resolution,
follow the procedure below.
●●Windows 10
1. Right-click the mouse anywhere on the desktop except on icons.
2. From the displayed menu, click “Display Settings”.
3. If multiple monitors are connected to the computer, select the monitor.
4. Select the resolution from the “Resolution” pull-down menu.
5. When a confirmation screen appears, click “Keep changes”.
●●Windows 8.1 / Windows 7
1. For Windows 8.1, click the "Desktop" tile on the Start Screen to display the desktop.
2. Right-click the mouse anywhere on the desktop except on icons.
3. From the displayed menu, click “Screen resolution”.
4. Select a monitor, then choose a resolution from the "Resolution" pull-down menu.
5. Click the "OK" button.
6. When a confirmation dialog box is displayed, click “Keep changes”.
●●OS X Mountain Lion (10.8) or later
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog box is displayed, click “Displays”. (For OS X Mountain Lion
(10.8), click "Displays" for "Hardware".)
3. On the displayed dialog box, select the “Display” tab, then choose "Scaled" for “Resolutions”.
4. The list of selectable resolutions is displayed. Select the desired resolution. If the desired
resolution is not displayed in the list, hold down the Option key and select "Scaled".
5. Your selection will be reflected immediately. When you are satisfied with the selected resolution,
close the window.
●●Mac OS X 10.7
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.
3. On the displayed dialog box, select the “Display” tab and select the desired resolution in the
“Resolutions” field.
4. Your selection will be reflected immediately. If you are satisfied with the selected resolution, close
the window.
Chapter 1
Introduction
9
Chapter 2 Basic Adjustment/Setting
This monitor enables users to change the brightness according to personal preference or to suit the usage
environment and reduce power consumption to conserve energy.
This chapter describes the basic functions that can be adjusted and set using the switches on the front of the
monitor.
For advanced adjustment and setting procedures using the Setting menu, see “Chapter 3 Advanced
Adjustment/Setting” (page 14).
2-1. Switch Operation Method
1. Displaying the operation guide
1. Press any switch (except
).
The operation guide appears on the screen.
2. Adjusting/setting
1. Press a switch for adjustment/setting.
The Adjustment/Setting menu appears.
(A submenu may also be displayed. In this case, select the item for adjustment/setting using
select
.)
2. Perform adjustment/setting with the switches and select
3. Exiting
1. Select
10
to exit the menu.
Chapter 2 Basic Adjustment/Setting
to accept the changes.
and
2-2. Switching Input Signals
When a monitor has multiple signal inputs, the signal to display on-screen can be changed.
2-3. Switching Display Modes (Color Modes)
This product is preinstalled with color modes for various display purposes.
Switch the mode according to the purpose and content for display. This allows the monitor to display
images in a manner appropriate to the display content.
●●Display Modes
Color Mode
Purpose
User1
User2
Select either of these modes to set a user-defined display mode.
sRGB
This mode is suitable for matching color reproduction with peripheral devices that
support sRGB, such as when printing photos taken using a digital camera.
Paper
This mode uses color tones and contrast similar to that of paper to produce a printed
paper effect. It is suitable for displaying images from media such as books and
documents.
2-4. Conserving Energy
This monitor is equipped with EcoView functions to enable users to conserve energy.
Use this function to curtail unnecessary power consumption and save on electricity expenses. Saving
power also reduces carbon dioxide emissions.
Chapter 2 Basic Adjustment/Setting
11
Note
•• The power saving level (Power Reduction, CO2 Reduction, and Eco Performance Level) can be checked on the
“EcoView Settings” menu. The more indicators that light up representing the Eco Performance Level, the higher
the power saving level attained.
-- Power Reduction: the reduction in the backlight’s power consumption as a result of the adjusted brightness
value.
-- CO2 Reduction: converted from the “Power Reduction” value, this is an estimate of the quantity of CO2
emissions reduced when using the monitor for 1 hour.
•• The numeric value is a result of calculation based on a default setting (0.000555t-CO2/kWh) determined by a
Japanese ministerial ordinance (2006, Ministry of Economy, Trade and Industry, Ministry of Environment, civil
code article 3) and may differ depending on country and year.
Function
Description
Auto EcoView
The ambient light sensor on the front of the monitor detects the
ambient brightness to automatically adjust the screen brightness
to a comfortable level using the Auto EcoView function. The power
consumption of the backlight can be curtailed by adjusting the
brightness to an appropriate level.
This function can also mitigate eye strain and tiredness caused by a
screen that is too bright or too dark.
Use the “Advanced Settings” to set the automatic adjustment range to
suit the monitor’s usage environment or personal preference.
Setting Range: On, Off
Note
•• Be careful not to block the ambient light sensor on the lower side
of the monitor when using the Auto EcoView function.
•• Even when the Auto EcoView setting is “On”, the
operation
switch on the front of the monitor or color adjustment can be
used to change the “Brightness” to suit your personal preference.
Moreover, the manner in which the Auto EcoView function changes
brightness also differs according to the changed value.
Advanced
Settings
Maximum
Minimum
Brightness
Set the range for automatic brightness adjustment.
By setting the maximum value and minimum value of the adjustment
range in advance, the brightness will be adjusted automatically within
the set range.
Setting Range: 0 to 100
Note
•• The maximum and minimum brightness values cannot be set to
the same value.
Ambient Light
Using the default setting is recommended.
(Default setting: “Bright” for maximum value, “Dark” for minimum value)
Setting Range: Bright, Dark, Standard
Note
•• For details on the “Ambient Light” setting, refer to our web site
(http://www.eizoglobal.com).
Reset
12
Chapter 2 Basic Adjustment/Setting
Return the advanced settings to their default values.
2-5. Adjusting Brightness
The brightness of the screen can be adjusted to suit the installation environment or personal preference.
The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD
back panel).
Setting Range
0 to 100
Note
•• When Auto EcoView is set to “On”, the adjustment range is restricted as follows. (For details on Auto EcoView,
see “Auto EcoView” (page 12).)
-- The brightness setting cannot be increased or decreased past the maximum and minimum brightness values
specified in the advanced settings of Auto EcoView.
-- Brightness may not be adjusted when the installation environment of the monitor is excessively bright or dark.
2-6. Adjusting Volume
The volume of the speakers and headphones can be set individually.
Setting Range
0 to 30
When the speakers are
connected
When the headphones are
connected
Chapter 2 Basic Adjustment/Setting
13
Chapter 3 Advanced Adjustment/Setting
This chapter describes the advanced monitor adjustment and setting procedures using the Setting menu.
For basic functions, see “Chapter 2 Basic Adjustment/Setting” (page 10).
3-1. Basic Operation of the Setting Menu
1. Menu display
1. Press any switch (except
).
The operation guide appears.
2. Select
.
The Setting menu appears.
2. Adjusting/setting
1. Select a menu to adjust/set with
and select
.
and select
.
The Sub menu appears.
2. Select an item to adjust/set with
The Adjustment/Setting menu appears.
3. Perform adjustment/setting with
or
and select
to accept the changes.
The Sub menu appears.
Selecting
during adjustment/setting will cancel the adjustment/setting and restore the state prior to
making changes.
3. Exiting
1. Selecting
14
several times will terminate the Setting menu.
Chapter 3 Advanced Adjustment/Setting
3-2. Setting Menu Functions
●●Color Adjustment
The color mode setting status can be adjusted according to personal preference.
Attention
•• It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more
after power to the monitor has been turned on before adjusting the monitor.
•• The same image may be observed in different colors on multiple monitors due to monitor-specific
characteristics. Make fine color adjustments visually when matching colors across multiple monitors.
Functions that can be adjusted differ depending on the color mode.
√: Adjustable -: Not adjustable
Function
Color Mode
Color Mode
User1
User2
sRGB
Paper
√
√
√
Description
Select the desired mode according to the monitor
application.
The color setting status can also be adjusted
according to personal preference. Select the mode
for adjustment and perform adjustment using the
relevant functions.
Setting Range: User1, User2, sRGB, Paper
Note
•• For details on the adjustment status of each
mode, see “2-3. Switching Display Modes
(Color Modes)” (page 11).
Brightness
√
√
√
The screen brightness is adjusted by changing the
brightness of the backlight (light source from the
LCD back panel).
Setting Range: 0 to 100
Note
•• If the image is too dark even when the
brightness is set to 100, adjust the contrast.
Chapter 3 Advanced Adjustment/Setting
15
√: Adjustable -: Not adjustable
Function
Contrast
Color Mode
User1
User2
sRGB
Paper
√
-
-
Description
The brightness of the screen is adjusted by varying
the video signal level.
Setting Range: 0 to 100
Note
•• A contrast of 50 displays every color gradation.
•• When adjusting the monitor, it is recommended
to perform brightness adjustment, which does
not lose gradation characteristics, prior to
contrast adjustment.
•• Perform contrast adjustment in the following
cases.
--If the image is too dark even when the
brightness is set to 100 (Set the contrast to
higher than 50.)
Temperature
√
-
√
Adjust the color temperature.
The color temperature is normally used to express
the hue of “White” and/or “Black” with a numerical
value. The value is expressed in degrees “K”
(Kelvin).
The screen becomes reddish at low color
temperatures and bluish at high color temperatures,
similar to the temperatures of a flame. A gain
preset value is set for each color temperature
setting value.
Setting Range: Off, 4000 K to 10000 K (in
increments of 500 K. 9300 K is included.)
Note
•• The value shown in “K” is available only as a
reference.
•• “Gain” allows you to perform more advanced
adjustment.
•• If set to “Off”, the image is displayed in the
preset color of the LCD panel (Gain: 100 for
each RGB channel).
•• When the gain is changed, the color
temperature setting changes to “Off”.
Gamma
√
-
-
Adjust the gamma.
While the brightness of the monitor varies
depending on the input signal, the variation rate is
not proportional to the input signal. Maintaining the
balance between the input signal and brightness of
the monitor is referred to as “Gamma correction”.
Setting Range: 1.8, 2.0, 2.2, 2.4
Note
•• If “Paper” is selected for the color mode,
“Paper” is displayed for the gamma value.
16
Chapter 3 Advanced Adjustment/Setting
√: Adjustable -: Not adjustable
Function
Advanced
Settings
Hue
Color Mode
User1
User2
sRGB
Paper
√
-
-
Description
Adjust the hue.
Setting Range: -50 to 50
Note
•• Using this function may prevent some color
gradations from being able to be displayed.
Saturation
√
-
-
Adjust the color saturation.
Setting Range: -50 to 50
Note
•• Using this function may prevent some color
gradations from being able to be displayed.
•• The minimum value (-50) changes the screen
to monochrome.
Gain
√
-
-
The brightness of each red, green, and blue color
component is referred to as “Gain”. The hue of
“white” can be changed by adjusting the gain.
Setting Range: 0 to 100
Note
•• Using this function may prevent some color
gradations from being able to be displayed.
•• The gain value changes according to the color
temperature.
•• When the gain is changed, the color
temperature setting changes to “Off”.
Reset
√
√
√
Reset any color adjustments for the currently
selected color mode back to the default settings.
Chapter 3 Advanced Adjustment/Setting
17
●●Signal Settings
Set the method for outputting the signal input from the PC to the monitor.
The setting range of each function differs depending on the input signal.
√: Settable -: Not settable
Function
Sharpness
Input Signal
DVI
D-Sub
√
√
Description
When an image is displayed in low resolution, text
or lines in the displayed image may be blurred.
This function reduces this blurring effect.
Setting Range: -2 to 2
Note
•• The sharpening setting may not be required
depending on the display resolution.
(“Sharpness” cannot be selected in such
cases.)
Analog
Adjustment
Auto Screen
Adjust
-
√
Screen flickering, display position, and size can
be adjusted automatically. Selecting “Auto Screen
Adjust” displays a message. Select “Yes” to
enable this function.
Note
•• The automatic screen adjustment function
works correctly when an image is fully
displayed over the entire displayable area of
the screen. It does not work properly in the
following cases:
--When an image is only displayed on part of
the screen (command prompt window, for
example)
--When a black background (wallpaper, etc.)
is used
Also, this function may not work properly with
some graphic boards.
•• When a signal is input into the monitor for
the first time or when a resolution or vertical/
horizontal scan frequency not used before
is set, the self adjustment function will
activate automatically (only for signals with a
resolution of 800×600 (SVGA) or higher).
Auto Range
Adjust
18
-
Chapter 3 Advanced Adjustment/Setting
√
Every color gradation (0 to 255) can be displayed
by automatically adjusting the signal output
level. Selecting “Auto Range Adjust” displays a
message. Select “Yes” to enable this function.
√: Settable -: Not settable
Function
Clock
Input Signal
DVI
D-Sub
-
√
Description
Flickering of vertical lines on the screen or part of
the screen can be reduced.
Note
•• Use the operation switches (
) to make
fine adjustments so as not to miss any
adjustment points.
Phase
-
√
Flickering and blurring over the entire screen can
be reduced.
Note
•• Flickering and blurring may not be completely
eliminated depending on your PC or graphics
board.
•• After setting, adjust the “Clock” again if
vertical bars appear.
Hor. Position
Ver. Position
-
√
The display position (horizontal and vertical) of the
screen can be adjusted.
Chapter 3 Advanced Adjustment/Setting
19
●●Preference Settings
The monitor’s settings can be configured to suit the usage environment or personal preference.
Function
Menu Rotation
Description
Change the orientation of the Setting menu when using the monitor screen in the portrait
display position.
Setting Range: 0°, 90°
Note
•• When using the monitor screen in a portrait position, a graphics board that supports
portrait display is required. When placing the monitor in a portrait position, the settings
of your graphics board need to be changed. Refer to the User’s Manual of the graphics
board for details. Also refer to our web site (http://www.eizoglobal.com).
Power Save
The monitor can be set to enter power saving mode according to the state of the PC.
The monitor changes to power saving mode about 15 seconds after signal input ceases to
be detected.
When the monitor has shifted to power saving mode, images are not displayed on the
screen.
•• Exiting power saving mode
--If the monitor receives input, it automatically exits power saving mode and returns to
the normal display mode.
Setting Range: On, Off
Note
•• At the time of shifting to power saving mode, a message that indicates the transition is
displayed 5 seconds in advance.
•• When not using the monitor, you can disconnect the power plug so that the power is cut
completely.
•• Power consumption varies even when the stereo mini jack cable is connected.
Power Indicator The power indicator (white) can be turned off during screen display.
Setting Range: On, Off
Monitor Reset
Restore all settings to their default values except for the following settings.
•• Settings on the “Administrator Settings” menu
Note
•• For details on the "Administrator Settings" menu, see “Chapter 4 Administrator Settings”
(page 22).
20
Chapter 3 Advanced Adjustment/Setting
●●Language
The display language for menus and messages can be selected.
Setting Range
English, Deutsch, Français, Español, Italiano, Svenska, Japanese, Simplified Chinese, Traditional
Chinese
Attention
•• The display language of the “Administrator Settings” menu cannot be changed.
●●Information
Monitor information (product name, serial number, usage time, input signal, and resolution) can be
checked.
Chapter 3 Advanced Adjustment/Setting
21
Chapter 4 Administrator Settings
This chapter describes how to configure monitor operation using the “Administrator Settings” menu.
This menu is for administrators. Configuration on this menu is not required for normal monitor use.
4-1. Basic Operation of the “Administrator Settings”
Menu
1. Menu display
1. Press
to turn off the monitor.
2. While pressing the leftmost switch, press
for more than 2 seconds to turn on the monitor.
The “Administrator Settings” menu appears.
2. Setting
1. Select an item to set with
and select
.
The Adjustment/Setting menu appears.
2. Set with
and select
.
The “Administrator Settings” menu appears.
3. Applying and exiting
1. Select “Apply” and then
.
The settings are applied and the “Administrator Settings” menu exits.
Attention
•• The language (English) of the “Administrator Settings” menu cannot be changed.
22
Chapter 4 Administrator Settings
4-2. Functions of the “Administrator Settings” Menu
Function
Auto Input Detection
Description
This product automatically recognizes the connector through which PC signals are
input and displays images on the screen accordingly. When a PC is turned off or
enters power saving mode, any other available signal is displayed automatically.
When this function is set to “Off”, the monitor displays the signal from the selected
connector regardless of whether a signal is input or not. In this case, select the input
signal to display using the
operation switch on the front of the monitor.
Setting Range: On, Off
Note
•• This product automatically recognizes the connector through which PC signals are
input, and displays images on the screen accordingly regardless of whether this
function is set to On or Off just after the power code is connected.
•• When this function is set to “On”, the monitor only enters power saving mode after
all connected PCs have entered power saving mode or have been switched off.
Compatibility Mode
Depending on the PC and graphics board, the input signal may not be detected and
the monitor may not recover from power saving mode. If this happens, set this function
to “On”.
Setting Range: On, Off
On-Screen Logo
When the monitor is turned on, the EIZO logo appears on the screen.
When this function is set to “Off”, the EIZO logo does not appear.
Setting Range: On, Off
Key Lock
In order to prevent changes to settings, the operation switches on the front of the
monitor can be locked.
Setting Range: Off, Menu, All
•• “Off”
Enables all switches.
•• “Menu”
Locks the
switch.
•• “All”
Locks all switches except the power switch.
Chapter 4 Administrator Settings
23
Chapter 5 Troubleshooting
5-1. No Picture
Problem
1. No picture.
•• Power indicator does not light up.
•• Check whether the power cord is connected properly.
•• Press .
•• Power indicator is lighting white.
•• Increase “Brightness”, “Contrast”, or “Gain” in the
Setting menu (see “Color Adjustment” (page 15)).
•• Power indicator is lighting orange.
••
••
••
••
2. The message below appears.
•• The message shows that the input signal is out
of the specified frequency range.
Example:
24
Possible cause and remedy
Chapter 5 Troubleshooting
Switch the input signal.
Move the mouse or press any key on the keyboard.
Check whether the PC is turned on.
Depending on the PC and graphics board, the input
signal may not be detected and the monitor may not
recover from power saving mode. If the screen is not
displayed by moving the mouse or pressing keys on the
keyboard, perform the following procedure. This may
resolve the problem.
1. Press
to turn off the monitor.
2. While pressing the leftmost switch, press
for
more than 2 seconds.
The “Administrator Settings” menu appears.
3. Select “Compatibility Mode”.
4. Select “On”.
5. Select “Apply” and then .
6. Reboot the PC.
This message appears when the signal is not input correctly
even though the monitor is functioning properly.
•• Check whether the PC is configured to meet the
resolution and vertical scan frequency requirements of
the monitor (see “1-2. Supported Resolutions” (page
8)).
•• Reboot the PC.
•• Select an appropriate setting using the graphics board’s
utility. Refer to the User’s Manual of the graphics board
for details.
5-2. Imaging Problems (For Both Digital and Analog)
Problem
Possible cause and remedy
1. The screen is too bright or too dark.
•• Use “Brightness” or “Contrast” in the Setting menu to
adjust it (see “Color Adjustment” (page 15)). (The LCD
monitor backlight has a limited life span. If the screen
becomes dark or begins to flicker, contact your local EIZO
representative.)
•• If the screen is too bright, try changing the Auto EcoView
setting to “On”. The monitor detects the ambient
brightness to adjust the screen brightness automatically
(see “Auto EcoView” (page 12)).
2. Brightness changes on its own.
•• Try changing the Auto EcoView setting to “Off” (see “Auto
EcoView” (page 12)).
3. “Brightness” cannot be adjusted.
•• Cannot increase/decrease setting value
( or
is displayed in gray)
--“Brightness” menu via
operation switch
/
--“Brightness” menu in color adjustment
/
•• Cannot increase/decrease setting value
( and
are displayed in gray)
--“Brightness” menu via
operation switch
--“Brightness” menu in color adjustment
When Auto EcoView is set to “On”, “Brightness” may not be
adjustable due to the advanced settings of Auto EcoView.
•• The bright adjustment range of the Auto EcoView function
can be limited to ensure that the screen is neither too
bright nor too dark. When the adjustment range is limited,
values outside the range cannot be set. If you want to
set a value outside the range, try changing the following
settings.
--Change the maximum and minimum values for
“Brightness” in the Auto EcoView advanced settings.
--Set Auto EcoView to “Off”.
For details on Auto EcoView settings, see “Auto EcoView”
(page 12).
•• Brightness adjustment may not be possible when the
installation environment of the monitor is excessively
bright or dark. In this case, try changing the following
settings.
--Change the maximum and minimum values for “Ambient
Light” in the Auto EcoView advanced settings.
--Set Auto EcoView to “Off”.
For details on Auto EcoView settings, see “Auto EcoView”
(page 12).
4. Text is blurred.
•• Check whether the PC is configured to meet the resolution
and vertical scan frequency requirements of the monitor
(see “1-2. Supported Resolutions” (page 8)).
•• When an image is displayed with a resolution other than
recommended, text or lines in the displayed image may
blur. In this case, try adjusting “Sharpness” in the Setting
menu (see “Sharpness” (page 18)).
5. Afterimages appear.
•• Afterimages are particular to LCD monitors. Avoid
displaying the same image for a long time.
•• Use the screen saver or power saving function to avoid
displaying the same image for extended periods of time.
Depending on the image, an afterimage may appear even
if it was displayed for a short period of time. To remove
such a phenomenon, change the image or keep the power
turned off for several hours.
6. Green / red / blue / white / dark dots remain
on the screen.
•• This is due to LCD panel characteristics and not a
malfunction.
7. Interference patterns or pressure marks
remain on the LCD panel.
•• Leave the monitor with a white or black screen. The
symptom may disappear.
8. Noise appears on the screen.
•• When entering the signals of HDCP system, the normal
images may not be displayed immediately.
Chapter 5 Troubleshooting
25
5-3. Imaging Problems (For Analog Only)
Problem
26
Possible cause and remedy
1. Display position is incorrect.
•• Use “Position” in the Setting menu to correct the image
position (see “Hor. Position”, “Ver. Position” (page 19)).
•• If the problem persists, use the graphics board’s utility if
available to change the display position.
2. Vertical bars appear on the screen or a part
of the image is flickering.
•• Use “Clock” in the Setting menu to adjust it (see “Clock”
(page 19)).
3. Whole screen is flickering or blurring.
•• Use “Phase” in the Setting menu to adjust it (see “Phase”
(page 19)).
Chapter 5 Troubleshooting
5-4. Other Problems
Problem
Possible cause and remedy
1. The Setting menu does not appear.
•• Check whether the switch operation lock function is active
(see “Key Lock” (page 23)).
2. No audio output.
•• Check whether the stereo mini jack cable is connected
properly.
•• Check whether volume is set to 0.
•• Check the PC and audio playback software to see
whether they are configured correctly.
Chapter 5 Troubleshooting
27
Chapter 6 Reference
6-1. Attaching the Optional Arm
An optional arm (or an optional stand) can be attached by removing the stand section. Please refer to our
web site for the supported optional arm (or optional stand). http://www.eizoglobal.com
Attention
•• When attaching an arm or stand, follow the instructions of the respective User’s Manual.
•• When using another manufacturer’s arm or stand, confirm the following in advance and select one conforming to
the VESA standard. Use the screws securing the unit and the stand.
-- Clearance between screw holes: 100 mm × 100 mm
-- Plate thickness: 2.6 mm
-- Strong enough to support weight of the monitor unit (excluding the stand) and attachments such as cables.
•• When attaching an arm or stand, the installable orientations and movement range (tilt angle) are as follows:
Orientation
Movement
range
(tilt angle)
Up: 45˚
Down: 45˚
Up: 45˚
Down: 45˚
•• Connect the cables after attaching an arm or stand.
•• Do not move the removed stand up and down. Doing so may result in injury or device damage.
•• The monitor, arm, and stand are heavy. Dropping them may result in injury or equipment damage.
28
Chapter 6
Reference
Attachment procedure
1. Lay the LCD panel on a soft cloth spread over a stable and flat surface
with the LCD panel surface facing down.
2. Remove the stand.
Prepare a screwdriver.
Use the screwdriver to loosen the screws (four) that secure the unit to the stand.
3. Attach the arm or stand to the monitor.
Secure the monitor to the arm or stand using the screws specified in the User’s Manual of the
arm or stand.
6-2. Connecting Multiple PCs
This product can be connected to multiple PCs and allows you to switch between the connections for
display.
Connection examples
DVI-D
FD-C39 (supplied)
D-Sub
MD-C87 (supplied)
DVI-D
D-Sub mini 15-pin
Note
•• The input signal changes each time the operation switch ( ) on the front of the monitor is pressed. When the
signal is switched, the active input port name appears at the top right corner of the screen.
•• This product automatically recognizes the connector through which PC signals are input and displays images on
the screen accordingly. For details, see “Auto Input Detection” (page 23).
Chapter 6
Reference
29
6-3. Specifications
LCD Panel
Type
TN (Anti-Glare)
Backlight
LED
Size
43 cm (17 inch)
Native Resolution
1280 dots × 1024 lines
Display Size (H × V)
337.9 mm × 270.3 mm
Pixel Pitch
0.264 mm
Display Colors
8-bit colors: 16.77 million colors
Viewing Angle
(H / V, typical)
170˚ / 160˚
Response Time (typical) Black-to-white-to-black: Approx. 5 ms
Video Signals
Audio
Power
Input Terminals
DVI-D (Applicable to HDCP) × 1 and D-Sub mini 15-pin × 1
Digital Scanning
Frequency
(H / V)
31 kHz to 64 kHz / 59 Hz to 61 Hz (VGA TEXT: 69 Hz to 71 Hz)
Analog Scanning
Frequency
(H / V)
31 kHz to 64 kHz / 55 Hz to 61 Hz (VGA TEXT: 69 Hz to 71 Hz)
Synchronization Signal
Separate
Max. Dot Clock
108 MHz
Speakers
0.5 W + 0.5 W
Headphones
2 mW + 2 mW (32 Ω)
Input Terminals
Line: Analog audio input connector × 1
Output Terminals
Headphone: Stereo mini jack × 1
Input
100 - 240 VAC ±10 %, 50 / 60 Hz 0.35 A - 0.20 A
Maximum Power
Consumption
18 W or less
Power Save Mode
0.5 W or less (default settings)
Standby Mode
0.5 W or less (default settings)
Physical Specifications Dimensions
(Without Stand)
Net Weight
367 mm × 304 mm × 59 mm (W × H × D)
Physical Specifications Dimensions
(Tilt Stand)
Net Weight
367 mm × 384 mm × 188 mm (W × H × D)
Tilt
Physical Specifications Dimensions
(Height Adjustable
Net Weight
Stand)
Height Adjustment
Range
Operating
Environmental
Requirements
Chapter 6
Approx. 4.4 kg
Up 30˚, Down 5˚
367 mm × 391.5 mm to 491.5 mm × 205 mm (W × H × D)
Approx. 5.4 kg
100 mm
Tilt
Up 30˚, Down 0˚
Swivel
Left 35˚, Right 35˚
Vertical Rotation
Right 90°
Temperature
5 ˚C to 35 ˚C
Humidity
20 % to 80 % R.H. (no condensation)
Air Pressure
540 hPa to 1060 hPa
Transportation/Storage Temperature
Environmental
Humidity
Requirements
Air Pressure
30
Approx. 3.6 kg
Reference
-20 ˚C to 60 ˚C
10 % to 90 % R.H. (no condensation)
200 hPa to 1060 hPa
●●Accessories
Cleaning Kit
EIZO “ScreenCleaner”
For the latest information about accessories, refer to our web site. http://www.eizoglobal.com
Chapter 6
Reference
31
Appendix
Trademark
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing, LLC in the United States and other countries.
The DisplayPort Compliance Logo and VESA are registered trademarks of the Video Electronics
Standards Association.
The SuperSpeed USB Trident Logo is a registered trademark of USB Implementers
Forum, Inc.
DICOM is the registered trademark of the National Electrical Manufacturers Association for its standards
publications relating to digital communications of medical information.
Kensington and Microsaver are registered trademarks of ACCO Brands Corporation.
Thunderbolt is a trademark of Intel Corporation in the United States and/or other countries.
Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and
other countries.
Adobe is a registered trademark of Adobe Systems Incorporated in the United States and other
countries.
Apple, macOS, Mac OS, OS X, Macintosh and ColorSync are registered trademarks of Apple Inc.
EIZO, the EIZO Logo, ColorEdge, CuratOR, DuraVision, FlexScan, FORIS, RadiCS, RadiForce,
RadiNET, Raptor and ScreenManager are registered trademarks of EIZO Corporation in Japan and other
countries.
ColorEdge Tablet Controller, ColorNavigator, EcoView NET, EIZO EasyPIX, EIZO Monitor Configurator,
EIZO ScreenSlicer, G-Ignition, i•Sound, Quick Color Match, RadiLight, Re/Vue, Screen Administrator,
Screen InStyle and UniColor Pro are trademarks of EIZO Corporation.
All other company and product names are trademarks or registered trademarks of their respective
owners.
License
The bitmap font used for this product is designed by Ricoh Industrial Solutions Inc.
32
Appendix
FCC Declaration of Conformity
For U.S.A., Canada Only
FCC Declaration of Conformity
We, the Responsible Party
EIZO Inc.
5710 Warland Drive, Cypress, CA 90630
Phone: (562) 431-5011
declare that the product
Trade name: EIZO
Model: FlexScan S1703-A
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures.
*
*
*
*
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Note
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep interference
within the limits of a Class B digital device.
--AC Cord
--Shielded Signal Cable (enclosed)
Canadian Notice
This Class B information technology equipment complies with Canadian ICES-003.
Cet équipement informatique de classe B est conforme à la norme NMB-003 du Canada.
Appendix
33
03V27254B1
UM-S1703-A
Copyright © 2018 EIZO Corporation. All rights reserved.
2nd Edition-May, 2018
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising