Eizo | T1781 | User manual | Eizo T1781 User Manual

Eizo T1781 User Manual
Instructions for Use
■User’s Manual
Important
Please read PRECAUTIONS, this User’s Manual, and the Setup Guide
(separate volume) carefully to familiarize yourself with safe and
effective usage.
• Please refer to the Setup Guide for basic information ranging from
connection of the monitor to a PC to using the monitor.
• The latest User’s Manual is available for download from our web site:
http://www.eizoglobal.com
Location of Caution Statement
WARNING
AVERTISSEMENT
WARNUNG
Symbol on the Unit
Symbol
This symbol indicates
Power Button
Press to turn the monitor’s power on or off.
Alternating current
Alerting electrical hazard
Caution
Refer to SAFETY SYMBOLS section in PRECAUTIONS.
This product has been adjusted specifically for use in the region to which it was originally shipped. If operated
outside this region, the product may not perform as stated in the specifications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information confidential unless prior
arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every effort has been
made to ensure that this manual provides up-to-date information, please note that EIZO monitor specifications are
subject to change without notice.
2

Notice for this monitor
This product is suited to general purposes like creating documents, viewing multimedia content.
This product has been adjusted specifically for use in the region to which it was originally shipped. If the product is
used outside the region, it may not operate as specified in the specifications.
This product may not be covered by warranty for uses other than those described in this manual.
The specifications noted in this manual are only applicable when the following are used:
· Power cords provided with the product
· Signal cables specified by us
Only use optional products manufactured or specified by us with this product.
If you place this product on a lacquer-coated desk, the color may adhere to the bottom of the stand due to the
composition of the rubber. Check the desk surface before use.
It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more after the
monitor power has been turned on, and then adjust the monitor.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and maintain a
stable display.
When the screen image is changed after displaying the same image for extended periods of time, an afterimage may
appear. Use the screen saver or power save function to avoid displaying the same image for extended periods of time.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer to
“Cleaning” (page 4)).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may appear on
the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994% or higher.
The backlight of the LCD panel has a fixed lifetime. When the screen becomes dark or begins to flicker, please contact
your local EIZO representative.
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do not attempt
to brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may
occur on the interior and exterior surfaces of the monitor. In that case, do not turn the monitor on. Instead wait until
the dew condensation disappears, otherwise it may cause some damage to the monitor.
(Cautions for the Use of the Touch Panel)
• During touch operation
Be careful of the following points. Otherwise, damage may occur to the monitor.
-- Do not strongly press, scratch, or poke the panel.
-- Do not touch the panel with hard objects such as ballpoint pens or metals.
Notice for this monitor
3
Cleaning
Attention
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or panel,
and also quality deterioration of the image.
• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.
• Do not allow liquid to enter the clearance between the panel and the panel frame.
The stains on the cabinet and panel surface can be removed by using the provided cleaning cloth.
To use the monitor comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according to
the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
4
Notice for this monitor
CONTENTS
Notice for this monitor.......................................... 3
Cleaning..................................................................... 4
To use the monitor comfortably.............................. 4
CONTENTS.............................................................. 5
Chapter 1
Introduction........................................ 7
1-1.
Features.......................................................... 7
1-2.
Controls and Functions................................ 8
1-3.
EIZO LCD Utility Disk...................................10
1-4.
Basic Operations and Functions................11
●●Attaching the touch pen holder........................ 9
●●Disk contents and software overview.............10
●●Basic operation of the Setting menu...............11
●●Functions.........................................................12
Chapter 2
2-1.
Adjusting Screens........................... 13
Compatible Resolutions..............................13
●●Analog Input (D-Sub)......................................13
●●Digital Input (DVI-D)........................................13
●●Digital Input (DisplayPort)...............................13
2-2.
Setting the Resolution.................................14
●●
●●
●●
●●
Windows 10.....................................................14
Windows 8.1 / Windows 7...............................14
Windows XP....................................................14
Mac OS X........................................................14
2-3.
Adjusting Color.............................................15
●●To select the display mode
(FineContrast Mode).......................................15
●●To perform advanced adjustments.................16
●●Adjustable settings in each mode...................16
●●To adjust brightness........................................16
●●To adjust contrast............................................17
●●To adjust color temperature............................17
●●To adjust gamma ............................................18
●●To adjust the color saturation..........................18
●●To adjust hue...................................................19
●●To set overdrive intensity................................19
●●To adjust gain................................................. 20
2-4.
Screen Adjustment.......................................21
2-5.
Screen Size Changing................................. 25
●●Digital Signal Input..........................................21
●●Analog Signal Input.........................................21
●●Screen Size Changing................................... 25
●●To adjust brightness of non-display area....... 25
Chapter 3
Setting Monitor................................ 26
3-1.
Adjusting Volume........................................ 26
3-2.
Selecting sound source while using the
DisplayPort signal input............................. 26
3-3.
Enabling / Disabling DDC/CI
communication ........................................... 26
3-4.
Locking Operation Buttons........................ 27
3-5.
Showing and hiding the EIZO logo............ 27
3-6.
Changing Setting Menu Display Position.... 27
3-7.
Setting Language......................................... 27
3-8.
Resetting the Monitor to the Default
Settings......................................................... 28
●●To reset the color adjustments....................... 28
●●To reset all adjustments to the default
settings........................................................... 28
Chapter 4
Touch Panel Settings...................... 29
4-1.
Touch Panel Setting Method...................... 29
4-2.
Calibrating the Monitor............................... 30
4-3.
Configuring Touch Panel Operation
Settings..........................................................31
Chapter 5
Power Saving Functions................. 32
5-1.
Setting Power Saving.................................. 32
5-2.
Setting Power Indicator............................... 33
5-3.
Enabling / Disabling Automatic
Brightness Adjustment .............................. 33
5-4.
Checking the power saving level............... 34
5-5.
Enabling / Disabling Auto Power-OFF....... 34
●●Monitor........................................................... 32
●●Audio Output.................................................. 33
Chapter 6
Troubleshooting............................... 35
6-1.
No picture..................................................... 35
6-2.
Imaging problems (for both digital and
analog)........................................................... 36
6-3.
Imaging problems (for analog only)...........37
6-4.
Touch panel problems................................. 38
6-5.
Other problems............................................ 40
Chapter 7
Reference......................................... 41
7-1.
Attaching the Optional Arm.........................41
7-2.
Connecting Multiple PCs............................ 43
7-3.
Making Use of USB (Universal Serial
Bus)................................................................ 45
●●To switch among input signals....................... 43
●●To set input signal selection........................... 44
●●Required System Environment...................... 45
●●Connection Procedure (Setup of USB
Function)......................................................... 45
7-4.
Displaying Monitor Information................. 45
7-5.
Specifications.............................................. 46
●●Main Default Settings......................................47
●●Outside Dimensions....................................... 48
●●Accessories.................................................... 48
CONTENTS
5
7-6.
Preset Timing............................................... 49
Chapter 8
Glossary........................................... 50
Appendix............................................................... 52
Trademark................................................................ 52
License / Copyright................................................. 52
Medical Standards.................................................. 53
FCC Declaration of Conformity............................. 54
EMC Information..................................................... 55
LIMITED WARRANTY.............................................. 58
Recycling Information............................................ 67
6
CONTENTS
Chapter 1 Introduction
Thank you very much for choosing an EIZO color LCD monitor.
1-1. Features
•
•
•
•
17.0″ LCD
Supports a resolution of 1280 × 1024
IPS panel with 89˚ horizontal and vertical viewing angles
Touch Panel provided
-- Projected capacitive technology
-- Supported OS: Microsoft Windows 10 / Windows 8.1 / Windows 7 / Windows XP
-- Supports the Windows Touch function (multi-touch) of Microsoft Windows 10 / Windows 8.1 /
Windows 7.*1
*1 This product supports up to five simultaneous touches (multi-touch support).
• 3 signal input terminals (DVI-D × 1, DisplayPort × 1, D-Sub × 1)
-- Applicable to DisplayPort (applicable to 8 bit)*2
The DisplayPort input receives both an image signal and an audio signal via a single DisplayPort cable.
*2 When transmitting an audio signal using the DisplayPort cable, the graphics board must be compatible with
audio output (see “7-5. Specifications” (page 46)).
• The FineContrast function allows the user to select the display mode optimum to the displayed image.
-- The Paper mode reproduces a printed paper effect on the monitor.
See “To select the display mode (FineContrast Mode)” (page 15).
• Flattening of the bezel allows smooth touch operations.
• Small footprint achieved through low-profile and lightweight design
The monitor can be readily moved and its position adjusted.
• The software “ScreenManager Pro for LCD (DDC/CI)” to adjust the screen using the mouse and keyboard is
included.
See “1-3. EIZO LCD Utility Disk” (page 10).
-- EyeCare Filter
Texture of the paper is reproduced by displaying a translucent image in the foreground of the desktop.
By using this function with the Paper mode, the screen looks more like paper.
See “To select the display mode (FineContrast Mode)” (page 15).
• Power saving function
Suppressing the power consumption reduces the carbon dioxide emissions. This product is equipped with power saving
function.
-- 0 W power consumption when the main power is off
Equipped with main power switch.
When the monitor is not required, the power supply can be shut off using the main power switch.
-- EcoView Optimizer 2
The monitor automatically adjusts the screen brightness according to the white level of the input signal. This
function can reduce the power consumption while maintaining the brightness specified by the input signal.
See “5-3. Enabling / Disabling Automatic Brightness Adjustment” (page 33).
• Displays HDCP (High-bandwidth Digital Protection) protected contents.
Chapter 1 Introduction
7
1-2. Controls and Functions
17
1
2
3
12
13
14
11
4
5
Setting menu*1
9
6
15
16
10
7
8
1.
button
2.
3.
4.
5.
button
button*2
,
button
button
Switches input signals for display (page 43).
Changes the FineContrast mode (page 15).
• Provides the menu selection as well as the adjustment and setting of a function.
•
button: Displays the Brightness adjustment menu (page 16).
button: Displays the volume adjustment menu (page 26).
Displays the Setting menu, determines an item on the menu screen, and saves values
adjusted (page 11).
Turns the power on or off.
Indicates the monitor’s operation status.
6. Power indicator
Blue:
Operating
Orange:
Power saving mode
OFF:
Main power / Power off
7. Main power switch
Turns the main power on or off.
8. Power connector
Connects the power cord.
9. Security lock slot
Complies with Kensington’s MicroSaver security system.
10. Stand
(with cable holder)
Used to adjust the angle of the monitor screen.
11. Speaker
Outputs audio source.
12. Headphone jack
Connects the headphones.
13. Stereo mini jack
Connects the stereo mini jack cable.
14. Input signal connector
Top: D-Sub mini 15-pin connector / Center: DVI-D connector / Bottom: DisplayPort
connector
15. USB port (DOWN)
Connects a peripheral USB device.
16. USB port (UP)
Connects the USB cable for using the monitor as a touch panel monitor or for using the
USB Hub function (page 45).
17. Touch pen holder
attachment hole*3
Used to attach a touch pen holder.
*1 See “1-4. Basic Operations and Functions” (page 11) for how to use.
*2 In this User’s Manual, the
button may be hereafter simply displayed as , and the
button as .
*3 The touch pen holder is supplied with the touch pen (Accessories (page 48)). Refer to the next page regarding the attachment
method.
8
Chapter 1 Introduction
●●Attaching the touch pen holder
Note
• The touch pen holder is supplied with the touch pen (Accessories (page 48)).
1. Align the touch pen holder over either the left or right attachment hole.
2. Attach with the screw supplied with the touch pen.
1.
2.
Chapter 1 Introduction
9
1-3. EIZO LCD Utility Disk
An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk contents
and the overview of the software programs.
●●Disk contents and software overview
The disk includes adjustment software, touch panel software, and user’s manuals. Refer to Readme.txt file on
the disk for software startup procedures or file access procedures.
Item
Overview
Screen adjustment pattern files
Used when adjusting the image of analog signal input manually.
Touch panel driver
Touch panel driver supplied by EIZO.*1
TPOffset
Software for adjusting the sensitivity of the touch panel.*1
Use this software when touch operations are not registered or only
registered after pressing hard.
ScreenManager Pro for LCD
(DDC/CI)
Software for adjusting the screen using the mouse and keyboard.*1
EIZO ScreenSlicer
Software that divides a screen and lays out multiple windows efficiently.*1
User’s Manual of this monitor (PDF file)
Readme.txt file
*1 Only for Windows. Refer to the corresponding User’s Manual on the CD-ROM for details on installation and use.
10
Chapter 1 Introduction
1-4. Basic Operations and Functions
●●Basic operation of the Setting menu
1. Displaying the Setting menu
1. Press
. The Setting menu appears.
2. Adjusting / Setting
1. Choose a menu to adjust / set with , , and then press
. The Sub menu appears.
2. Choose an item to adjust / set with , , and then press
. The adjustment / setting menu appears.
3. Adjust / set the selected item with , , and then press
3. Exiting
1. Choose “Return” from the Sub menu and press
2. Choose “Exit” from the Main menu and press
.
. The Setting menu appears.
. The Setting menu quits.
Note
• The Setting menu can also be exited by pressing
twice quickly.
Chapter 1 Introduction
11
●●Functions
The following table shows the Setting menu and setting items of each menu.
Main menu
Color*1
Screen
Sound
Setting
Brightness
Contrast
Temperature
Gamma
Advanced Settings
Reference
“2-3. Adjusting Color” (page 15)
Saturation
Hue
Overdrive
Gain
Color Reset
Screen Size
Smoothing
Analog Adjustment*2 Auto Screen Adjust
Auto Range Adjust
Clock
Phase
Hor.Position
Ver.Position
Source
“To reset the color adjustments” (page 28)
“Screen Size Changing” (page 25)
“2-4. Screen Adjustment” (page 21)
“3-2. Selecting sound source while using
the DisplayPort signal input” (page 26)
Power Save
“Audio Output” (page 33)
PowerManager
Power Save
“5-1. Setting Power Saving” (page 32)
Eco Timer
“5-5. Enabling / Disabling Auto PowerOFF” (page 34)
Monitor Settings
Input Signal
“To set input signal selection” (page 44)
Power Indicator
“5-2. Setting Power Indicator” (page 33)
Language
“3-7. Setting Language” (page 27)
DDC/CI
“3-3. Enabling / Disabling DDC/CI
communication” (page 26)
Border Intensity
“To adjust brightness of non-display area”
(page 25)
Menu Settings
Logo
“3-5. Showing and hiding the EIZO logo”
(page 27)
Menu Position
“3-6. Changing Setting Menu Display
Position” (page 27)
Reset
“To reset all adjustments to the default
settings” (page 28)
EcoView
EcoView Optimizer 2
“5-3. Enabling / Disabling Automatic
Brightness Adjustment” (page 33)
Information
“7-4. Displaying Monitor Information”
(page 45)
*1 The adjustment / settings available on the “Color” menu depend on the selected Color mode (see “Adjustable
settings in each mode” (page 16)).
*2 These functions can be adjusted with analog input.
12
Chapter 1 Introduction
Chapter 2 Adjusting Screens
2-1. Compatible Resolutions
The monitor supports the following resolutions.
●●Analog Input (D-Sub)
Resolution
Applicable Signals
640 × 480
720 × 400
800 × 600
1024 × 768
1280 × 720
1280 × 960
1280 × 1024*1
VGA, VESA
VGA TEXT
VESA
VESA
CEA-861
VESA
VESA
Vertical Scan
Frequency
Dot Clock
~75 Hz
70 Hz
~75 Hz
~75 Hz
60 Hz
60 Hz
~75 Hz
135 MHz
(Max.)
Vertical Scan
Frequency
Dot Clock
●●Digital Input (DVI-D)
Resolution
Applicable Signals
640 × 480
720 × 400
800 × 600
1024 × 768
1280 × 720
1280 × 960
1280 × 1024*1
VGA
VGA TEXT
VESA
VESA
CEA-861
VESA
VESA
60 Hz
70 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
108 MHz
(Max.)
Vertical Scan
Frequency
Dot Clock
●●Digital Input (DisplayPort)
Resolution
Applicable Signals
640 × 480
720 × 400
720 × 480 (4:3)
720 × 480 (16:9)
800 × 600
1024 × 768
1280 × 720
1280 × 960
1280 × 1024*1
VGA, CEA-861
VGA TEXT
CEA-861
CEA-861
VESA
VESA
CEA-861
VESA
VESA
60 Hz
70 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
108 MHz
(Max.)
*1 Recommended resolution
Chapter 2 Adjusting Screens
13
2-2. Setting the Resolution
When you connect the monitor to the PC and find that the resolution is improper, or when you want to change the
resolution, follow the procedure below.
●●Windows 10
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Display Settings”.
3. On the “Customize your display” dialog box, click “Advanced display settings”.
4. Select a monitor, then choose a resolution from the “Resolution” pull-down menu.
5. Click the “Apply” button.
6. When a confirmation dialog box is displayed, click “Keep changes”.
●●Windows 8.1 / Windows 7
1. For Windows 8.1, click the “Desktop” tile on the Start Screen to display the desktop.
2. Right-click the mouse anywhere on the desktop except for icons.
3. From the displayed menu, click “Screen resolution”.
4. On the “Screen Resolution” dialog box, select the monitor.
5. Click “Resolution” to select the desired resolution.
6. Click the “OK” button.
7. When a confirmation dialog box is displayed, click “Keep changes”.
●●Windows XP
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Properties”.
3. When the “Display Properties” dialog box is displayed, click the “Settings” tab and select desired resolution
for “Screen resolution” under “Display”.
4. Click the “OK” button to close the dialog box.
●●Mac OS X
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.
3. On the displayed dialog box, select the “Display” tab and select desired resolution in the “Resolutions” field.
4. Your selection will be reflected immediately. When you are satisfied with the selected resolution, close the
window.
14
Chapter 2 Adjusting Screens
2-3. Adjusting Color
●●To select the display mode (FineContrast Mode)
This function allows easy selection of a desired mode according to monitor application.
Display Modes
Mode
Purpose
User1
Select this to define a desired set of parameter settings.
User2
sRGB
Suitable for color matching with sRGB compatible peripherals.
Paper
Produces a printed paper effect. Suitable for displaying images from media such as books
and documents.
Movie
Suitable for playing back animated images.
The mode menu
appears.
Procedure
1. Press
.
The mode menu appears at the bottom left of the screen.
2. The mode among the list is highlighted in turn each time
You can switch the mode with
or
is pressed.
while the mode menu is displayed.
→User1←→User2←→sRGB←→Paper←→Movie←
Note
• The Setting menu and the Mode menu cannot be displayed at the same time.
• “ScreenManager Pro for LCD (DDC/CI)” allows you to select the FineContrast mode automatically according to the
application used (see “Chapter 3 Auto FineContrast” in the “ScreenManager Pro for LCD (DDC/CI)” User’s Manual).
Chapter 2 Adjusting Screens
15
●●To perform advanced adjustments
The “Color” menu of the Setting menu allows you to set and save the independent color adjustment for each
mode.
Attention
• It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more after the
monitor power has been turned on, and then adjust the monitor.
• Perform the range adjustment first when adjusting color for analog signals (see “To adjust color gradation automatically”
(page 24)).
• The same image may be seen in different colors on multiple monitors due to their monitor-specific characteristics. Make
fine color adjustment visually when matching colors on multiple monitors.
Note
• Using the “ScreenManager Pro for LCD (DDC/CI)” allows you to perform the color adjustment by using the mouse and
keyboard of your PC. (Refer to “Chapter 4 Color Adjustment” in the User’s Manual for “ScreenManager Pro for LCD
(DDC/CI)”.)
●●Adjustable settings in each mode
The adjustable settings depend on the mode. (Non-adjustable or non-settable function cannot be selected.)
√: Adjustable -: Not adjustable
Function
FineContrast Mode
User1
User2
sRGB
Paper
Movie
Brightness
√
√
√
√
√
Contrast
√
√
-
-
√
Temperature
√
√
-
√
√
Gamma
√
√
-
-
-
Saturation
√
√
-
-
√
Hue
√
√
-
-
√
Overdrive
√
√
-
-
-
Gain
√
√
-
-
-
√
√
√
√
√
Advanced Settings
Color Reset
●●To adjust brightness
The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD back
panel).
Adjustable range
0 to 100
Procedure
.
1. Press
2. Use
3. Press
or
for adjustment.
to exit.
Note
• If you feel that the image is too dark even if the brightness is set to 100, adjust the contrast.
• Alternatively, you can use “Brightness” under “Color” in the Adjustment menu to adjust it.
• To adjust the screen brightness automatically and comfortably, see “5-3. Enabling / Disabling Automatic Brightness
Adjustment” (page 33).
16
Chapter 2 Adjusting Screens
●●To adjust contrast
The brightness of the screen is adjusted by varying the video signal level.
Adjustable range
0 to 100
Procedure
1. Choose “Color” in the Setting menu, and press
.
.
2. Choose “Contrast” in the “Color” menu, and press
The “Contrast” menu appears.
3. Use
or
for adjustment.
to exit.
4. Press
Note
• In the contrast of 50, every color gradation is displayed.
• When adjusting the monitor, it is recommended to perform the brightness adjustment which may not lose the gradation
characteristics, prior to the contrast adjustment.
• Perform the contrast adjustment in the following cases.
-- When you feel the image is too dark even if the brightness is set to 100 (Set the contrast to higher than 50.)
●●To adjust color temperature
Color temperature can be adjusted.
The color temperature is normally used to express the hue of “White” and / or “Black” by a numerical value.
The value is expressed in degrees “K” (Kelvin).
The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like the flame
temperature. A gain preset value is set for each color temperature setting value.
Adjustable range
Off, 4000 K-10000 K (specified by every 500 K unit, including 9300 K)
Procedure
1. Choose “Color” in the Setting menu, and press
2. Choose “Temperature” in the “Color” menu, and press
.
.
The “Temperature” menu appears.
3. Use
4. Press
or
for adjustment.
to exit.
Note
•
•
•
•
The value shown in “K” is available only as reference.
“Gain” allows you to perform more advanced adjustment (see “To adjust gain” (page 20)).
If you set to “Off”, the image is displayed in the preset color of the monitor (Gain: 100 for each RGB).
When gain is changed, the color temperature is changed to “Off”.
Chapter 2 Adjusting Screens
17
●●To adjust gamma
Gamma can be adjusted. The brightness of the monitor varies depending on the input signal, however, the
variation rate is not proportional to the input signal. To keep the balance between the input signal and the
brightness of the monitor is called as “Gamma correction”.
Adjustable range
1.8, 2.0, 2.2
Procedure
1. Choose “Color” in the Setting menu, and press
.
.
2. Choose “Gamma” in the “Color” menu, and press
The “Gamma” menu appears.
3. Use
or
for adjustment.
to exit.
4. Press
Note
• If “Paper” is selected in the FineContrast mode, the gamma value is displayed for “Paper”. The setting “Paper” is
specially meant to get the displayed image look like it is printed on paper.
●●To adjust the color saturation
This function allows you to adjust color saturation.
Adjustable range
-50 to 50
Procedure
1. Choose “Color” in the Setting menu, and press
.
2. Choose “Advanced Settings” in the “Color” menu, and press
3. Choose “Saturation” in the “Advanced Settings” menu, and press
The “Saturation” menu appears.
4. Use
5. Press
or
for adjustment.
to exit.
Attention
• Using this function may make some color gradations unavailable for display.
Note
• The minimum value (-50) changes the screen to monochrome.
18
Chapter 2 Adjusting Screens
.
.
●●To adjust hue
This function allows you to adjust hue.
Adjustable range
-50 to 50
Procedure
1. Choose “Color” in the Setting menu, and press
.
.
2. Choose “Advanced Settings” in the “Color” menu, and press
3. Choose “Hue” in the “Advanced Settings” menu, and press
.
The “Hue” menu appears.
4. Use
or
for adjustment.
to exit.
5. Press
Attention
• Using this function may make some color gradations unavailable for display.
●●To set overdrive intensity
This function allows you to set overdrive intensity based on the use of the monitor. You can reduce Image lags
by setting it to “Enhanced” when displaying animated images.
Adjustable range
Enhanced, Standard, Off
Procedure
1. Choose “Color” in the Setting menu, and press
.
2. Choose “Advanced Settings” in the “Color” menu, and press
3. Choose “Overdrive” in the “Advanced Settings” menu, and press
.
.
The “Overdrive” menu appears.
4. Use
5. Press
or
for adjustment.
to exit.
Attention
• The overdrive function is disabled in the following cases:
-- When the vertical scan frequency of input signals is more than 70 Hz
-- When “Normal” or “Enlarged” is selected from “Screen Size” (excluding the case that display resolution is 1280 ×
1024).
Chapter 2 Adjusting Screens
19
●●To adjust gain
The brightness of each color component red, green, and blue is called “Gain”. You can change the hue of
“white” by adjusting gain.
Adjustable range
0 to 100
Procedure
1. Choose “Color” in the Setting menu, and press
.
.
2. Choose “Advanced Settings” in the “Color” menu, and press
3. Choose “Gain” in the “Advanced Settings” menu, and press
.
The “Gain” menu appears.
4. Adjust gain with
5. Press
or
for each of red, green, and blue.
to exit.
Attention
• Using this function may make some color gradations unavailable for display.
Note
• The value of gain changes with that of color temperature.
• When gain is changed, the color temperature is changed to “Off”.
20
Chapter 2 Adjusting Screens
2-4. Screen Adjustment
●●Digital Signal Input
When digital signals are input, images are displayed correctly based on the preset data of the monitor, but if
characters and / or lines appear blurred, go to “To modify blurred characters / lines” (page 24).
When performing more advanced adjustment, see “2-3. Adjusting Color” (page 15) and subsequent pages.
●●Analog Signal Input
Attention
• It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more after the
monitor power has been turned on, and then adjust the monitor.
• The Self Adjust (automatic screen adjustment) function does not work for the images under the resolution of 800 × 600
(SVGA).
• The self adjustment (or automatic screen adjustment) function works correctly when an image is fully displayed over the
Windows or Macintosh display area. They do not work properly in the cases below:
-- When an image is displayed only on a part of the screen (command prompt window, for example)
-- When a black background (wallpaper, etc.) is in use
Also, these functions cannot work properly in some graphic boards.
The monitor screen adjustment is used to suppress flickering of the screen or adjust screen position and screen
size correctly according to the PC to be used.
Note
• The Self Adjust function works when all of the following conditions are satisfied:
-- When a signal is input into the monitor for the first time or when a resolution or vertical / horizontal scan frequency
not used before is set
If the screen is not displayed correctly even after performing the Self Adjust operation, adjust the screen
according to the procedures on the following pages to use the monitor comfortably.
Setting Procedures
1. Perform the auto adjustment.
●●To adjust flickering, screen position, and screen size automatically
Procedure
1. Choose “Screen” in the Setting menu, and press
.
2. Choose “Analog Adjustment” in the “Screen” menu, and press
.
3. Choose “Auto Screen Adjust” in the “Analog Adjustment” menu, and press
4. Select “Yes” with
or , and press
.
.
Flickering, screen position, and screen size are corrected by the auto-adjustment function.
If the screen is not displayed correctly even after performing the auto adjustment, perform adjustments
according to the following procedure. If the screen is displayed correctly, go to “5. Adjusting color gradation.”
(page 24).
Chapter 2 Adjusting Screens
21
2. Prepare to use analog screen adjustment patterns.
Load the “EIZO LCD Utility Disk” to your PC, and then open the “Screen adjustment pattern files”.
Note
• For details and instructions on opening the “Screen adjustment pattern files”, refer to the Readme.txt file.
3. Perform the auto adjustment again with the analog screen adjustment pattern
displayed.
●●To adjust flickering, screen position, and screen size automatically
Procedure
1. Display Pattern 1 in full screen on the monitor using the “Screen adjustment pattern files”.
2. Choose “Screen” in the Setting menu, and press
.
.
3. Choose “Analog Adjustment” in the “Screen” menu, and press
4. Choose “Auto Screen Adjust” in the “Analog Adjustment” menu, and press
5. Select “Yes” with
or , and press
.
.
Flickering, screen position, and screen size are corrected by the auto-adjustment function.
If the screen is not displayed correctly even after performing the auto adjustment, perform adjustments
according to the following procedure. If the screen is displayed correctly, go to “5. Adjusting color gradation.”
(page 24).
4. Choose “Screen” from the Setting menu to perform advanced adjustments.
Adjust the clock, phase and position, in this order.
●●To eliminate vertical bars
Procedure
.
1. Choose “Analog Adjustment” in the “Screen” menu, and press
2. Choose “Clock” in the “Analog Adjustment” menu, and press
.
The “Clock” menu appears.
3. Adjust the clock with
Press
4. Press
or
or
to eliminate vertical bars.
slowly so as not to miss the adjustment point.
to exit.
When blurring, flickering or bars appear on the screen after adjustment, proceed to “To remove flickering or blurring ”.
22
Chapter 2 Adjusting Screens
●●To remove flickering or blurring
Procedure
.
1. Choose “Analog Adjustment” in the “Screen” menu, and press
2. Choose “Phase” in the “Analog Adjustment” menu, and press
.
The “Phase” menu appears.
3. Adjust the phase with
4. Press
or
to minimize flickering or blurring.
to exit.
When vertical bars appear on the screen after adjustment, go back to “To eliminate vertical bars ”.
(Clock → Phase → Position)
Attention
• Flickering or blurring may not be eliminated depending on your PC or graphics board.
●●To correct the screen position
Note
• Since the number of pixels and the pixel positions are fixed on the LCD monitor, only one position is provided to display
images correctly. The position adjustment is made to shift an image to the correct position.
Procedure
1. Choose “Analog Adjustment” in the “Screen” menu, and press
.
2. Choose “Hor.Position” or “Ver.Position” from the “Analog Adjustment” menu, and press
.
The “Hor. Position” or “Ver. Position” menu appears.
3. Adjust the position with
4. Press
or .
to exit.
5. Close Pattern 1.
Chapter 2 Adjusting Screens
23
5. Adjusting color gradation.
●●To adjust color gradation automatically
Every color gradation (0 to 255) can be displayed by adjusting the signal output level.
Procedure
1. Display Pattern 2 in full screen on the monitor using the “Screen adjustment pattern files”.
2. Choose “Screen” in the Setting menu, and press
.
3. Choose “Analog Adjustment” in the “Screen” menu, and press
.
4. Choose “Auto Range Adjust” in the “Analog Adjustment” menu, and press
5. Select “Yes” with
or , and press
.
.
The output range is set automatically.
6. Close Pattern 2.
6. Modify blurred characters or lines.
●●To modify blurred characters / lines
When an image is displayed with a resolution other than recommended, the characters or lines of the
displayed image may blur.
Attention
• Smoothing setting may not be required depending on the display resolution. (You cannot choose the smoothing icon.)
Adjustable range
1 to 5
Procedure
1. Choose “Screen” in the Setting menu, and press
2. Choose “Smoothing” in the “Screen” menu, and press
The “Smoothing” menu appears.
3. Use
4. Press
24
or
for adjustment.
to exit.
Chapter 2 Adjusting Screens
.
.
2-5. Screen Size Changing
●●Screen Size Changing
The image with the resolution other than the recommended resolution is displayed in full screen automatically.
You can change the screen size by using the “Screen Size” function.
Setting
Function
Full Screen
Displays an image in full screen. Images are distorted in some cases because the vertical
rate is not equal to the horizontal rate.
Enlarged
Displays an image in full screen. In some cases, a blank horizontal or vertical border
appears to equalize the vertical rate and the horizontal rate.
Normal
Displays images with the specified resolution.
Example: Image size 1024 × 768
Full Screen
Enlarged
Normal
(1280 × 1024)
(1280 × 960)
(1024 × 768)
Procedure
.
1. Choose “Screen” in the Setting menu, and press
.
2. Choose “Screen Size” in the “Screen” menu, and press
The “Screen Size” menu appears.
3. Select “Full Screen”, “Enlarged”, or “Normal” with
or .
to exit.
4. Press
Attention
• Selecting “Normal” may make some color gradations unavailable for display.
●●To adjust brightness of non-display area
A border (black area with no image) around the image appears in the “Normal” or “Enlarged” mode.
Border
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
.
2. Choose “Border Intensity” in the “Monitor Settings” menu, and press
.
The “Border Intensity” menu appears.
3. Use
4. Press
or
for adjustment.
to exit.
Chapter 2 Adjusting Screens
25
Chapter 3 Setting Monitor
3-1. Adjusting Volume
This function allows you to adjust the volume.
Adjustable range
0 to 30
Procedure
.
1. Press
2. Use
or
3. Press
for adjustment.
to exit.
Note
• The volume for the speakers and the headphone can be set individually.
3-2. Selecting sound source while using the DisplayPort
signal input
This function allows you to switch sound source during DisplayPort signal input. You can select the Stereo Mini
Jack or DisplayPort.
Procedure
1. Choose “Sound” in the Setting menu, and press
.
.
2. Choose “Source” in the “Sound” menu, and press
The “Source” menu appears.
3. Select “Stereo Mini Jack” or “DisplayPort” with
4. Press
or .
to exit.
Note
• This function is available with DisplayPort signal input.
3-3. Enabling / Disabling DDC/CI communication
This function allows you to enable / disable the DDC/CI communication (see “Chapter 8 Glossary” (page 50)).
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
2. Choose “DDC/CI” in the “Monitor Settings” menu, and press
.
.
The “DDC/CI” menu appears.
3. Select “On” or “Off” with
4. Press
or .
to exit.
Note
• The DisplayPort input of this monitor does not support DDC/CI communication.
26
Chapter 3 Setting Monitor
3-4. Locking Operation Buttons
This function allows you to lock the settings to prevent them being changed.
Procedure
1. Press
to turn off the monitor.
while pressing
2. Hold down
to turn on the monitor.
The Lock / Unlock setting is toggled by performing the operation in step 2.
Note
• The following operations are available even if the buttons are locked:
-- Turning on or off the monitor with the Power button
3-5. Showing and hiding the EIZO logo
When the monitor is turned on, the EIZO logo appears on the screen. You can choose to show or hide the display of
the EIZO logo.
Procedure
.
1. Choose “Monitor Settings” in the Setting menu, and press
.
2. Choose “Menu Settings” in the “Monitor Settings” menu, and press
3. Choose “Logo” in the “Menu Settings” menu, and press
.
The “Logo” menu appears.
4. Select “On” or “Off” with
5. Press
or .
to exit.
3-6. Changing Setting Menu Display Position
You can change the display position of the Setting menu.
Procedure
.
1. Choose “Monitor Settings” in the Setting menu, and press
.
2. Choose “Menu Settings” in the “Monitor Settings” menu, and press
.
3. Choose “Menu Position” in the “Menu Settings” menu, and press
The “Menu Position” menu appears.
4. Choose the position with
5. Press
or .
to exit.
3-7. Setting Language
This function allows you to select a language for the Setting menu or messages.
Selectable languages
English, German, French, Spanish, Italian, Swedish, Japanese, Simplified Chinese, Traditional Chinese
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
2. Choose “Language” in the “Monitor Settings” menu, and press
.
.
The “Language” menu appears.
3. Choose a language with
4. Press
or .
to exit.
Chapter 3 Setting Monitor
27
3-8. Resetting the Monitor to the Default Settings
The setting values are reset to the default settings.
Attention
• After resetting, you cannot undo the operation.
Note
• Regarding the default setting, see “Main Default Settings” (page 47).
●●To reset the color adjustments
This function only resets the color adjustments for the currently selected mode to the default settings.
Procedure
1. Choose “Color” in the Setting menu, and press
.
2. Choose “Color Reset” in the “Color” menu, and press
3. Select “Yes” with
4. Press
.
or .
.
The color adjustments revert to the default settings.
●●To reset all adjustments to the default settings
This function resets all adjustments to the default settings.
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
2. Choose “Reset” in the “Monitor Settings” menu, and press
3. Select “Yes” with
4. Press
or .
.
All adjustments revert to the default settings.
28
Chapter 3 Setting Monitor
.
.
Chapter 4 Touch Panel Settings
4-1. Touch Panel Setting Method
There are multiple touch panel setting methods as shown below. Configure settings to meet your usage applications.
Windows standard driver
( Windows 8.1 / Windows 7 )
Touch panel driver supplied by EIZO
Mouse emulation mode
(Mouse.mfd*1)
Touch digitizer mode
(Touch.mfd*1)
Driver
You do not need to install the
driver.
Install the touch panel driver on the “EIZO LCD Utility Disk” (CDROM).
Setting
Use Windows Control Panel.
Use the “Touch Screen Properties” supplied with the touch panel
driver.
Operation You can not set the touch sound. You can set the touch sound.
*1
Only one touch panel monitor
can be connected.
Multiple touch panel monitors can be connected.
Up to five simultaneous touch
points are available.
Up to five simultaneous touch
points are available.
Only single point touch is
available.
Enables the same operations as
those of the mouse as well as
multi-touch operations such as
image zoom and rotation.
Enables the same operations as
those of the mouse as well as
multi-touch operations such as
image zoom and rotation.
The cursor reacts in the same
way when you operate the
mouse.
Select “Basic Setting” - “Configuration File” in “Touch Screen Properties”, and select the desired configuration file.
Note
• When setting is completed, execute the “TPOffset” application on the “EIZO LCD Utility Disk” (CD-ROM), and adjust the
sensitivity of the touch panel.
Attention
• When the touch panel driver supplied by EIZO is used in Windows XP, only the mouse emulation mode is available. If you
select the touch digitizer mode, the touch position may not be recognized correctly.
For details on the touch panel driver supplied by EIZO, refer to the touch panel driver user’s manual (on CD-ROM).
When using the Windows standard driver, configure settings, referring to the following information.
Chapter 4 Touch Panel Settings
29
4-2. Calibrating the Monitor
Attention
• Do not put your hands or any metal close to the screen because the screen is susceptible to electrical conductors.
• If a “User Account Control” dialog box is displayed during operation, proceed according to the displayed instructions.
1. Open the Windows Control Panel.
The method for opening the Control Panel differs depending on the OS.
Windows 8.1
1. Click
at the bottom of the “Start” screen.
The “Apps” screen appears.
2. Click “Control Panel” under “Windows System”.
Windows 7
1. Click “Start” - “Control Panel”.
2. Click “Hardware and Sound” - “Tablet PC Settings”.
The “Tablet PC Settings” window appears.
3. Click “Setup” in the “Display” tab.
A touchscreen specification screen with a white background is displayed.
Attention
• If using the monitor in a multiple monitor environment, specify the touchscreen according to the message displayed on
screen.
4. Touch the screen with your finger.
The touched screen is recognized as a touchscreen.
5. Press “Enter” on the keyboard.
The “Tablet PC Settings” window reappears.
30
Chapter 4 Touch Panel Settings
6. Click “Calibrate”.
A calibration screen with a white background is displayed.
Attention
• If using the monitor in a multiple monitor environment, select the monitor for calibration from the “Display” pulldown
menu and then click “Calibrate”.
7. Touch the calibration target (cross) for a few seconds with your finger and
release.
The calibration target appears on the screen 16 times, starting from the top left to top right and then down to
the bottom left to bottom right.
Note
• For second or subsequent calibrations, the calibration target appears 4 times.
8. After completing calibration, click “Yes” to save the calibration data.
9. Click “OK” to close the window.
4-3. Configuring Touch Panel Operation Settings
1. Open the Windows Control Panel.
The method for opening the Control Panel differs depending on the OS (see page 30).
2. Click “Hardware and Sound” - “Pen and Touch”.
“Pen and Touch” window appears.
Configure the touch panel operation settings in the “Pen and Touch” window. For detailed settings, refer to the
settings on each tab and Windows Help.
3. After completing settings, click “OK” to close the window.
Chapter 4 Touch Panel Settings
31
Chapter 5 Power Saving Functions
5-1. Setting Power Saving
●●Monitor
This function allows you to set the monitor into the power saving mode according to the PC status. When the
monitor has shifted to the power saving mode, the images on the screen are not displayed.
Attention
• Turning off the main power switch or unplugging the power cord completely shuts off power supply to the monitor.
• When the monitor is in power saving mode, devices connected to the USB downstream port will still work. Therefore,
power consumption of the monitor varies with connected devices even in the power saving mode.
• Power consumption varies even when the stereo mini jack cable is connected.
Note
• The monitor changes to the power saving mode about 15 seconds after the signal input ceases to be detected.
Procedure
.
1. Choose “PowerManager” in the Setting menu, and press
.
2. Choose “Power Save” in the “PowerManager” menu, and press
The “Power Save” menu appears.
3. Select “On” or “Off” with
4. Press
or .
to exit.
Power Saving System
Analog Signal Input
This monitor complies with the VESA DPM standard.
PC
On
Power saving
mode
STAND-BY
SUSPENDED
OFF
Power Off
Monitor
Power Indicator
Operating
Blue
Power saving mode
Orange
Power saving mode
Orange
Digital Signal Input
• DVI
This monitor complies with the DVI DMPM standard.
• DisplayPort
This monitor complies with the DisplayPort Standard.
PC
Monitor
Power Indicator
On
Operating
Blue
Power saving mode
Power saving mode
Orange
Power Off
Power saving mode
Orange
Exiting the power saving mode
If the monitor receives input, it automatically exits the power saving mode and returns to the normal display
mode.
32
Chapter 5 Power Saving Functions
●●Audio Output
This monitor allows you to turn off the audio output from the speakers / headphone at the power saving mode.
Procedure
1. Choose “Sound” in the Setting menu, and press
.
.
2. Choose “Power Save” in the “Sound” menu, and press
The “Power Save” menu appears.
3. Select “Sound On” or “Sound Off” with
4. Press
or .
to exit.
5-2. Setting Power Indicator
This function allows you to set the power indicator (blue) ON / OFF in the monitor ON condition.
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
.
2. Choose “Power Indicator” in the “Monitor Settings” menu, and press
.
The “Power Indicator” menu appears.
3. Select “On” or “Off” with
4. Press
or .
to exit.
5-3. Enabling / Disabling Automatic Brightness
Adjustment
Using the EcoView Optimizer 2 function automatically adjusts the screen brightness according to the white
level of the input signal. This function can reduce the power consumption while maintaining the brightness
specified by the input signal.
Procedure
1. Choose “EcoView” in the Setting menu, and press
.
2. Choose “EcoView Optimizer 2” in the “EcoView Menu” menu, and press
.
The “EcoView Optimizer 2” menu appears.
3. Select “On” or “Off” with
4. Press
or .
to exit.
Note
• When “Movie” is selected from the FineContrast mode, the setting is turned “Off”.
• When the EcoView Optimizer 2 function is “On”, the appearance of pale color may change. If that bothers you, set this
function to “Off”.
Chapter 5 Power Saving Functions
33
5-4. Checking the power saving level
The EcoView menu allows you to check Power Reduction, CO2 Reduction, and Eco Performance Level. The more
indicators light up representing the Eco Performance Level, the higher the power saving level attained.
Indicator
Procedure
.
1. Choose “EcoView” in the Setting menu, and press
The “EcoView Menu” menu appears.
Note
• Power reduction: the backlight’s reduction of power consumption as a result of the adjusted brightness value.
• CO2 reduction: converted from the “Power reduction” value, this is an estimate of the quantity of CO2 emissions reduced
when using the monitor for 1 hour.
* The numeric value is a result of a calculation based on a default setting (0.000555 t -CO2/kWh) determined by a Japanese
ministerial ordinance (2006, Ministry of Economy, Trade and Industry, Ministry of Environment, civil code article 3) and
may differ depending on country and year.
5-5. Enabling / Disabling Auto Power-OFF
This function allows you to switch the setting to turn off the monitor automatically after a specified time has passed
in the power saving mode.
Adjustable range
Off, 0, 1, 2, 3, 5, 10, 15, 20, 25, 30, 45 min, 1, 2, 3, 4, 5 h
Procedure
.
1. Choose “PowerManager” in the Setting menu, and press
2. Choose “Eco Timer” in the “PowerManager”, and press
3. Select “Off” or time to turn off the monitor with
4. Press
34
to exit.
Chapter 5 Power Saving Functions
or .
.
Chapter 6 Troubleshooting
If a problem still remains after applying the suggested remedies, contact your local EIZO representative.
6-1. No picture
Problem
1. No picture
• Power indicator does not light.
Possible cause and remedy
•
•
•
•
Check whether the power cord is connected properly.
Turn the main power switch on.
Press .
Turn off the main power, and then turn it on again a few
minutes later.
• Power indicator is lighting blue.
• Increase “Brightness”, “Contrast”, or “Gain” in the Setting
menu (see “To perform advanced adjustments” (page 16)).
• Power indicator is lighting orange.
•
•
•
•
•
Switch the input signal with
.
Move the mouse or press any key on the keyboard.
Touch the panel surface.
Check whether the PC is turned on.
Depending on the PC and graphics board, the input signal
is not detected and the monitor does not recover from
the power saving mode. If the screen is not displayed
even after moving the mouse or pressing any key on the
keyboard, turn the monitor off and on using its power
button. When the screen is displayed, execute the
following procedure. The problem may be improved.
1.
2.
Press
to turn off the monitor.
Hold down
while pressing
to turn on the
monitor.
“x” is displayed on the menu title of “Information” of the
Setting menu (see “7-4. Displaying Monitor Information”
(page 45)).
3. Reboot the PC.
To return to the previous setting, perform steps 1 to 3
again.
• Power indicator is flashing orange.
• The device that is connected using DisplayPort have a
problem. Solve the problem, turn off the monitor, and then
turn it on again. Refer to the User’s Manual of the output
device for further details.
Chapter 6 Troubleshooting
35
Problem
2. The message below appears.
• The message shows that the input signal is
out of the specified frequency range.
Example:
Possible cause and remedy
This message appears when the signal is not input correctly
even when the monitor functions properly.
• Check whether the PC is configured to meet the resolution
and vertical scan frequency requirements of the monitor
(see “2-1. Compatible Resolutions” (page 13)).
• Reboot the PC.
• Select an appropriate setting using the graphics board’s
utility. Refer to the User’s Manual of the graphics board
for details.
6-2. Imaging problems (for both digital and analog)
Problem
36
Possible cause and remedy
1. The screen is too bright or too dark.
• Use “Brightness” or “Contrast” in the Setting menu to
adjust it. (The LCD monitor backlight has a limited life
span. When the screen becomes dark or begins to flicker,
contact your local EIZO representative.)
2. Characters are blurred.
• Check whether the PC is configured to meet the resolution
and vertical scan frequency requirements of the monitor
(see “2-1. Compatible Resolutions” (page 13)).
• When an image is displayed with a resolution other than
recommended, the characters or lines of the displayed
image may blur. Use “Smoothing” and “Screen Size” in the
Setting menu to adjust the display (see “To modify blurred
characters / lines” (page 24), and “Screen Size Changing”
(page 25)).
3. Afterimages appear.
• Afterimages are particular to LCD monitors. Avoid
displaying the same image for a long time.
• Use the screen saver or power save function to avoid
displaying the same image for extended periods of time.
4. Green / red / blue / white dots or defective
dots remain on the screen.
• This is due to LCD panel characteristics and is not a
failure.
5. Interference patterns or pressure marks
remain on the screen.
• Leave the monitor with a white or black screen. The
symptom may disappear.
6. Noise appears on the screen.
• In the Setting menu, set “Overdrive” to “Off” (see “To set
overdrive intensity” (page 19)).
• When entering the HDCP signals, the normal images may
not be displayed immediately.
Chapter 6 Troubleshooting
6-3. Imaging problems (for analog only)
Problem
Possible cause and remedy
1. Display position is incorrect.
• Use “Position” in the Setting menu to correct the image
position (see “To correct the screen position” (page 23)).
• If the problem persists, use the graphics board’s utility if
available to change the display position.
2. Vertical bars appear on the screen or a
part of the image is flickering.
• Use “Clock” in the Setting menu to adjust it (see “To
eliminate vertical bars” (page 22)).
3. Whole screen is flickering or blurring.
• Use “Phase” in the Setting menu to adjust it (see “To
remove flickering or blurring” (page 23)).
Chapter 6 Troubleshooting
37
6-4. Touch panel problems
Problem
38
Possible cause and remedy
1. Touch operation is disabled.
• Check that the monitor and PC are connected with a USB
cable.
• Check that the power cord of the monitor and PC is
connected to a grounded main outlet. Failure to ground
the equipment may result in malfunction.
• Perform touch panel sensitivity adjustment using
TPOffset.
2. Cursor position is not correct. / Cursor
jumps.
• Connect the monitor to the PC with the cable indicated in
the Setup Guide. The touch panel may not work correctly
if a conversion adapter is used.
• Turn off and on the monitor.
• Calibrate the screen again.
• Check that the power cord of the monitor and PC is
connected to a grounded main outlet. Failure to ground
the equipment may result in malfunction.
• Perform touch panel sensitivity adjustment using
TPOffset.
• Changing the position or angle of the monitor may cause
the cursor to jump.
• Keep metals away from the panel surface.
• If the touch panel is dirty, the touch panel may not operate
properly. Refer to the User’s Manual of the monitor to
clean the touch panel.
• The spray for preventing static electricity may influence
the sensitivity of the touch panel.
• Do not touch the touch panel for 5 seconds after the PC
starts up, after turning on the monitor, or after connecting
the USB cable. Touching the touch panel too soon may
cause incorrect cursor positioning or disable touch
operation. If this occurs, either leave the touch panel
untouched for approximately 2 minutes or turn the monitor
off and on again. If the problem persists, calibrate the
screen again.
• Changing the screen size of the monitor may cause the
cursor position to become misaligned. Execute calibration
again after changing the screen size.
3. The cursor does not appear at the touched
position and instead is displayed at a
point-symmetric position with respect to
the center of the screen.
• Calibrate the screen again.
4. Cursor is jittery. / Drawing lines are not
straight and smooth.
• Check that the power cord of the monitor and PC is
connected to a grounded main outlet. Failure to ground
the equipment may result in malfunction.
• Perform touch panel sensitivity adjustment using
TPOffset.
• The influence of metal may cause jittery cursor.
• When multiple monitors are placed close to each other,
leave space between monitors.
Chapter 6 Troubleshooting
Problem
Possible cause and remedy
5. (If the OS being used is Windows 8.1 /
Windows 7)
Calibration does not work correctly.
• Reset the touch panel to the state before calibration (by
clicking “Reset” in the “Display” tab of the “Tablet PC
Settings” window accessible from the Windows Control
Panel) and then calibrate the touch panel again.
• Once “Setup” has been completed in the “Display” tab
of the “Tablet PC Settings” window accessible from the
Windows Control Panel, close the “Tablet PC Settings”
once, open the “Display” tab of “Tablet PC Settings” again,
and then attempt calibration.
6. (If the OS being used is Windows 10 /
Windows 8.1 / Windows 7)
No touch-sound.
• Sound is only output through the audio output terminal of
the PC. To hear touch sound, connect speakers.
• Sound is not output when touched positions are not
assigned any functions.
Attention
• For details on TPOffset (software for adjusting touch panel sensitivity), see the TPOffset User’s Manual (on the CD-ROM).
Chapter 6 Troubleshooting
39
6-5. Other problems
Problem
40
Possible cause and remedy
1. The Setting menu does not appear.
• Check whether the operation lock function is active (see
“3-4. Locking Operation Buttons” (page 27)).
2. The “Smoothing” on the Setting menu
“Screen” cannot be selected.
• You cannot choose “smoothing” when the screen is
displayed in the following resolutions or settings.
--The resolution is 1280 × 1024
--Screen Size is “Normal”
3. The auto adjustment function does not
work.
• This function does not work during digital signal input.
• This function is intended for use on the Macintosh and
on AT-compatible PC running Windows. It does not work
properly when an image is displayed only on a part of the
screen (command prompt window, for example) or when a
black background (wallpaper, etc.) is in use.
• This function does not work correctly with some graphics
boards.
4. No audio output.
• Check whether the stereo mini jack cable is connected
properly.
• Check whether volume is set to 0.
• Check the setting of the PC and the audio playback
software.
• During DisplayPort signal input, check the “Source”
setting (see “3-2. Selecting sound source while using the
DisplayPort signal input” (page 26)).
5. USB devices connected to the monitor
does not work.
• Check whether the USB cable is connected correctly (see
“7-3. Making Use of USB (Universal Serial Bus)” (page 45)).
• Change the USB port to another one. If the PC or
peripheral devices works correctly by changing the USB
port, contact your local EIZO representative. (Refer to the
manual of the PC for details.)
• Reboot the PC.
• If the peripheral devices work correctly when the PC and
peripheral devices are connected directly, please contact
your local EIZO representative.
• Check whether the PC and OS are USB compliant. (For
USB compliance of the respective devices, consult their
manufacturers.)
• Check the PC’s BIOS setting for USB when using
Windows. (Refer to the manual of the PC for details.)
Chapter 6 Troubleshooting
Chapter 7 Reference
7-1. Attaching the Optional Arm
An optional arm (or an optional stand) can be attached by removing the stand section.
Attention
• When attaching an arm or stand, follow the instructions of their User’s Manual.
• When using another manufacturer’s arm or stand, confirm the following in advance and select one conforming to the VESA
standard.
-- Clearance between the screw holes: 100 mm × 100 mm
-- Thickness of plate: 2.6 mm
-- Strong enough to support weight of the monitor unit (except the stand) and attachments such as cables.
• When using another manufacturer’s arm or stand, use the screws as described below.
-- Screws fixing the stand to the monitor
• When using an arm or stand, attach it to meet the following tilt angles of the monitor.
-- Up 90˚, down 5˚ (landscape display / turned 90˚ clockwise to portrait display)
• When setting the monitor to the portrait style, turn the monitor screen 90˚ in clockwise direction.
• Connect the cables after attaching an arm or stand.
• Do not move the removed stand up and down. Doing so may result in injury or device damage.
• The monitor and arm or stand are heavy. Dropping them may result in injury or equipment damage.
Procedure
1. Lay the LCD monitor on a soft cloth spread over on a stable surface with the
panel surface facing down.
2. Remove the stand.
Using a screwdriver, loosen the screws securing the unit and the stand.
3. Attach the arm or stand to the monitor.
Secure the monitor to the arm or stand using the screws specified in the User’s Manual of the arm or stand.
Chapter 7 Reference
41
Note
• When setting the monitor in the portrait orientation, remove the feet on the bottom of the monitor according to the
following procedure.
1. Remove the foot covers.
2. Remove the screw that secures each foot to the monitor.
3. Slide each foot toward the edge of the monitor and remove them as shown below.
4. Seal the holes by adhering the supplied stickers.
• Store the removed parts in a safe place.
42
Chapter 7 Reference
7-2. Connecting Multiple PCs
The product has multiple connections to PCs and allows you to switch to one of the connections for display.
Connection examples
Analog
(D-Sub)
Signal cable
(supplied MD-C87)
D-Sub
connector
D-Sub mini 15-pin
connector
To PC 1
Digital
(DVI)
Signal cable
(supplied FD-C39)
DVI-D
connector
DVI connector
Digital
(DisplayPort)
To PC 2
Signal cable
(option PP200)
DisplayPort
connector
DisplayPort
connector
To PC 3
●●To switch among input signals
The input signal switches each time
is pressed.
When the signal is switched, the active input port name appears at the top right corner of the screen.
Chapter 7 Reference
43
●●To set input signal selection
Setting
Function
Auto
The monitor recognizes the connector through which PC signals are input.
When a PC is turned off or enters the power saving mode, the monitor automatically
displays another signal.
Manual
The monitor detects only the PC’s signals currently displaying automatically. Select the
input signal for display using the
operation button.
Procedure
.
1. Choose “Monitor Settings” from the Adjustment menu, and press
2. Choose “Input Signal” from “Monitor Settings”, and press
3. Select “Auto” or “Manual” with
4. Press
.
or .
to exit.
Note
• If you select “Auto”, the monitor enters the power saving mode after all the PCs have entered the power saving mode or
have been switched off.
44
Chapter 7 Reference
7-3. Making Use of USB (Universal Serial Bus)
This monitor has a USB hub. It works as a USB hub when connected to a USB-compatible PC, allowing the
connection of peripheral USB devices.
●●Required System Environment
• A PC (including devices with a USB host function) and OS in conformance with USB Specification Revision
2.0
• USB cable
Attention
• This monitor may not work depending on PC, OS or peripheral devices to be used. For USB compatibility of peripheral
devices, contact their manufacturers.
• When the monitor is in power saving mode, devices connected to the USB downstream port will still work. Therefore,
power consumption of the monitor varies with connected devices even in the power saving mode.
• When the main power of the monitor is Off, a device connected to the USB downstream port will not operate.
●●Connection Procedure (Setup of USB Function)
1. Connect the monitor first to a PC using the signal cable, and run the PC.
2. Connect the USB cable between the USB downstream port of the PC and the USB upstream port of the
monitor.
The USB hub function is set up automatically upon connection of the USB cable.
3. Connect the peripheral USB devices to the USB downstream port of the monitor.
USB
downstream port
USB
upstream port
7-4. Displaying Monitor Information
This function allows you to display the model name, serial number, usage time, resolution, and input signal.
Procedure
1. Choose “Information” in the Setting menu, and press
.
The “Information” menu appears.
Attention
• When you turn on the monitor for the first time, the usage time may be more than 0 due to a factory inspection.
Chapter 7 Reference
45
7-5. Specifications
LCD Panel
Size
17.0-inch (430 mm)
Type
TFT color LCD, LED backlight
Viewing angles
Horizontal 178˚, vertical 178˚ (CR≥10)
Dot Pitch
0.264 mm
Response Time
Black-white-black: Approx. 22 ms
Gray-to-gray: Approx. 6 ms (Overdrive setting: Enhanced)
Touch panel
Surface treatment
Anti-glare
Surface hardness
5H
Communication
USB-based
Detection method
Projected capacitive technology
OS
Microsoft Windows 10 (32 bit / 64 bit)
Microsoft Windows 8.1 (32 bit / 64 bit)
Microsoft Windows 7 Service Pack 1 (32 bit / 64 bit)
Microsoft Windows XP Service Pack 3 (32 bit)
(Not compatible with Mac OS)
Number of
simultaneous touch
points
Microsoft Windows 10 / Windows 8.1 / Windows 7: Up to 5
(Microsoft Windows XP only supports single point touch)
Horizontal Scan Analog
Frequency
Digital
31 kHz - 81 kHz
DVI
31 kHz - 64 kHz
DisplayPort 31 kHz - 64 kHz
Vertical Scan
Frequency
Analog
Digital
55 Hz - 76 Hz (non-interlace)
DVI
59 Hz - 61 Hz (non-interlace) (VGA TEXT: 69 Hz - 71 Hz)
DisplayPort 59 Hz - 61 Hz (non-interlace) (VGA TEXT: 69 Hz - 71 Hz)
Resolution
Max. Dot Clock
1280 Dots × 1024 Lines
Analog
Digital
135 MHz
DVI
108 MHz
DisplayPort 108 MHz
Max. Display Color
Approx. 16.77 million colors
Display Area (H × V)
337.9 mm (13.3 inch) × 270.3 mm (10.6 inch)
Power Supply
100 - 120 VAC ±10 %, 50 / 60 Hz 0.7 A - 0.6 A
200 - 240 VAC ±10 %, 50 / 60 Hz 0.4 A - 0.35 A
Power
Consumption
Screen Display On
39 W or less
Power saving mode
0.7 W or less (When only the D-Sub connector is connected, no USB
device is connected, “Monitor Settings” - “Input Signal”:
“Auto”, and “Sound” - “Power Save”: “Sound Off”)
Power Off
0.7 W or less (When only the D-Sub connector is connected, no USB
device is connected)
Main Power Off
0W
Input Signal Connector
D-Sub mini 15-pin
DVI-D connector (Applicable to HDCP)
DisplayPort (Applicable to HDCP)
Applicable Format (Audio signal)
- 2ch linear PCM
(32 kHz / 44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz)
Analog Input Signal (Sync)
Separate, TTL, positive / negative
Analog Input Signal (Video)
Analog, Positive (0.7 Vp-p / 75 Ω)
Digital Signal (DVI) Transmission System TMDS (Single Link)
Audio Output
46
Chapter 7 Reference
Speaker output: 1.0 W + 1.0 W (8 Ω, THD+N: 10 % or less)
Headphone output: 2 mW + 2 mW (32 Ω, THD+N: 3 % or less)
Line Input
Input impedance: 44 kΩ (typ.)
Input level: 2.0 Vrms (Max.)
Plug & Play
Analog / Digital (DVI-D) : VESA DDC 2B / EDID structure 1.3
Digital (DisplayPort) : VESA DisplayPort / EDID structure 1.4
Dimensions
(Width) ×
(Height) ×
(Depth)
Main unit
392 mm (15.4 inch) × 142.5 mm - 356 mm (5.6 inch - 14 inch) × 89 mm 400.5 mm (3.5 inch - 15.8 inch)
Main unit (without
stand)
392 mm (15.4 inch) × 331 mm (13 inch) × 54 mm (2.13 inch)
Mass
Main unit
Approx. 4.8 kg (10.6 lbs.)
Main unit (without
stand)
Approx. 4.3 kg (9.5 lbs.)
Movable range
Environmental
Conditions
Temperature
Humidity
Air Pressure
USB
Tilt:
15˚ to 70˚
Operating:
5˚C to 35˚C (41˚F to 95˚F)
Transportation/
Storage:
-20˚C to 60˚C (-4˚F to 140˚F)
Operating:
20 % to 80 % R.H. (no condensation)
Transportation/
Storage:
10 % to 90 % R.H. (no condensation)
Operating:
540 hPa to 1,060 hPa
Transportation/
Storage:
200 hPa to 1,060 hPa
Standard
USB Specification Revision 2.0
Port
Upstream port × 1, Downstream port × 2
Communication Speed 480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low)
Supply current
Downstream:
Max. 500mA/1 port
●●Main Default Settings
EcoView Optimizer 2
On
FineContrast Mode
User1
Screen Size
Full Screen
Smoothing
3
Power Save
On
Eco Timer
Off
Language
English
Menu Position
Center
Input Signal
Auto
Chapter 7 Reference
47
●●Outside Dimensions
392
340
25.5
25
54
62
Unit: mm
89
215.5
90
400.5
340.5
349
70
°
33
25
142.5
102
272.5
331
15°
100
(VESA)
17.5
190
100
(VESA)
91
●●Accessories
Touch pen
Signal cable
TP5
PP200
For the latest information about the accessories, refer to our web site.
http://www.eizoglobal.com
48
Chapter 7 Reference
6
383
7-6. Preset Timing
The following table shows factory preset analog signal timing.
Attention
• Display position may be deviated depending on the PC connected, which may require screen adjustment using Setting menu.
• If a signal other than those listed in the table is input, adjust the screen using the Setting menu. However, screen display may
still be incorrect even after the adjustment.
• When interlace signals are used, the screen cannot be displayed correctly even after screen adjustment using the Setting
menu.
Resolution
Applicable
Signals
640 × 480
640 × 480
640 × 480
720 × 400
800 × 600
800 × 600
800 × 600
800 × 600
1024 × 768
1024 × 768
1024 × 768
1280 × 720
1280 × 960
1280 × 1024
1280 × 1024
VGA
VESA
VESA
VGA TEXT
VESA
VESA
VESA
VESA
VESA
VESA
VESA
CEA-861
VESA
VESA
VESA
Frequency
Dot Clock:
MHz
25.18
31.50
31.50
28.32
36.00
40.00
50.00
49.50
65.00
75.00
78.75
74.25
108.00
108.00
135.00
Polarity
Horizontal:
Vertical: Hz Horizontal
kHz
31.47
37.86
37.50
31.47
35.16
37.88
48.08
46.88
48.36
56.48
60.02
45.00
60.00
63.98
79.98
59.94
72.81
75.00
70.09
56.25
60.32
72.19
75.00
60.00
70.07
75.03
60.00
60.00
60.02
75.03
Negative
Negative
Negative
Negative
Positive
Positive
Positive
Positive
Negative
Negative
Positive
Positive
Positive
Positive
Positive
Vertical
Negative
Negative
Negative
Positive
Positive
Positive
Positive
Positive
Negative
Negative
Positive
Positive
Positive
Positive
Positive
Chapter 7 Reference
49
Chapter 8 Glossary
Clock
The analog signal input monitor needs to reproduce a clock of the same frequency as the dot clock of the
graphics system in use, when the analog signal is converted to a digital signal for image display. This is
called clock adjustment. If the clock pulse is not set correctly, some vertical bars appear on the screen.
DDC/CI (Display Data Channel/Command Interface)
VESA provides the standardization for the interactive communication of the setting information, etc.
between a PC and the monitor.
DisplayPort
This is the interface standard for image signals standardized in accordance with VESA. It was developed
with the aim of replacing the conventional DVI and analog interfaces, and it can transmit high resolution
signals and sound signals, which DVI does not support. It also supports 10-bit color, copyright protection
technology, long cables, etc. The standard size and mini size connectors have been standardized.
DVI (Digital Visual Interface)
DVI is a digital interface standard. DVI allows direct transmission of the PC’s digital data without loss.
This adopts the TMDS transmission system and DVI connectors. There are two types of DVI connectors.
One is a DVI-D connector for digital signal input only. The other is a DVI-I connector for both digital and
analog signal inputs.
DVI DMPM (DVI Digital Monitor Power Management)
DVI DMPM is a digital interface power saving function. The “Monitor ON (operating mode)” and “Active
Off (power saving mode)” are indispensable for DVI DMPM as the monitor’s power mode.
Gain
This is used to adjust each color parameter for red, green and blue. An LCD monitor displays the color by
the light passing through the panel color filter. Red, green and blue are the three primary colors. All the
colors on the screen are displayed by combining these three colors. The color tone can be changed by
adjusting the light intensity (volume) passing through each color’s filter.
Gamma
Generally, the monitor brightness varies nonlinearly with the input signal level, which is called “Gamma
Characteristic”. A small gamma value produces a low-contrast image, while a large gamma value produces a
highcontrast image.
HDCP (High-bandwidth Digital Content Protection)
Digital signal coding system developed to copy-protect the digital contents, such as video, music, etc.
This helps to transmit the digital contents safely by coding the digital contents sent via the DVI or HDMI
connector on the output side and decoding them on the input side.
Any digital contents cannot be reproduced if both of the equipments on the output and input sides are not
applicable to HDCP system.
50
Chapter 8 Glossary
Overdrive
This technology enhances response speed by increasing the potential difference at the time of motion of
liquid-crystal pixels, and it is used for liquid-crystal TV sets and others in general. It provides clear-cut
three-dimensional display with little afterimage, by improving response speed of the intermediate graduation
range that frequently appears in moving images.
Phase
Phase means the sampling timing to convert the analog input signal to a digital signal. Phase adjustment is
made to adjust the timing. It is recommended that phase adjustment be made after the clock is adjusted
correctly.
Range Adjustment
Range adjustment controls the signal output levels to display every color gradation. It is recommended that
range adjustment be made before color adjustment.
Resolution
The LCD panel consists of numerous pixels of specified size, which are illuminated to form images. This
monitor consists of horizontal 1280 pixels and 1024 vertical pixels. At a resolution of 1280 × 1024, all pixels
are illuminated as a full screen (1:1).
sRGB (Standard RGB)
International standard for color reproduction and color space among peripheral devices (such as monitors,
printers, digital cameras, scanners). As a form of simple color matching for the Internet, colors can be
displayed using tones close to those of the transmission and reception devices.
Temperature
Color temperature is a method to measure the white color tone, generally indicated in degrees Kelvin. The
screen becomes reddish at a low temperature, and bluish at a high temperature, like the flame temperature.
5000 K: Slightly reddish white
6500 K: White referred to as daylight-balanced color
9300 K: Slightly bluish white
TMDS (Transition Minimized Differential Signaling)
A signal transmission system for digital interface.
VESA DPM (Video Electronics Standards Association - Display Power
Management)
VESA specifications achieve increased energy efficiency for computer monitors. This involves
standardization of signals sent from the computer (graphics board).
DPM defines the status of signals transmitted between the computer and monitor.
Chapter 8 Glossary
51
Appendix
Trademark
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing, LLC in the United States and other countries.
The DisplayPort Compliance Logo and VESA are registered trademarks of the Video Electronics Standards
Association.
Acrobat, Adobe, Adobe AIR, and Photoshop are registered trademarks of Adobe Systems Incorporated in the
United States and other countries.
AMD Athlon and AMD Opteron are trademarks of Advanced Micro Devices, Inc.
Apple, ColorSync, eMac, iBook, iMac, iPad, Mac, MacBook, Macintosh, Mac OS, PowerBook, and QuickTime
are registered trademarks of Apple Inc.
ColorMunki, Eye-One, and X-Rite are registered trademarks or trademarks of X-Rite Incorporated in the United
States and/or other countries.
ColorVision and ColorVision Spyder2 are registered trademarks of DataColor Holding AG in the United States.
Spyder3 and Spyder4 are trademarks of DataColor Holding AG.
ENERGY STAR is a registered trademark of the United States Environmental Protection Agency in the United
States and other countries.
GRACoL and IDEAlliance are registered trademarks of International Digital Enterprise Alliance.
NEC is a registered trademark of NEC Corporation.
PC-9801 and PC-9821 are trademarks of NEC Corporation.
NextWindow is a registered trademark of NextWindow Ltd.
Intel, Intel Core, Pentium and Thunderbolt are trademarks of Intel Corporation in the United States and/or other
countries.
PowerPC is a registered trademark of International Business Machines Corporation.
PlayStation is a registered trademark of Sony Computer Entertainment Inc.
PSP and PS3 are trademarks of Sony Computer Entertainment Inc.
RealPlayer is a registered trademark of RealNetworks, Inc.
TouchWare is a trademark of 3M Touch Systems, Inc.
Windows, Windows Media, Windows Vista, SQL Server, and Xbox 360, and Internet Explorer are registered
trademarks of Microsoft Corporation in the United States and other countries.
YouTube is a registered trademark of Google Inc.
Firefox is a registered trademark of the Mozilla Foundation.
Kensington and MicroSaver are trademarks of ACCO Brands Corporation.
EIZO, the EIZO Logo, ColorEdge, DuraVision, FlexScan, FORIS, RadiCS, RadiForce, RadiNET, Raptor, and
ScreenManager are registered trademarks of EIZO Corporation in Japan and other countries.
ColorNavigator, EcoView NET, EIZO EasyPIX, EIZO ScreenSlicer, i • Sound, Screen Administrator, and UniColor
Pro are trademarks of EIZO Corporation.
All other company and product names are trademarks or registered trademarks of their respective owners.
License / Copyright
A round gothic bold bit map font designed by Ricoh is used for the characters displayed on this product.
52
Appendix
Medical Standards
• It shall be assured that the final system is in compliance to IEC60601-1-1 requirement.
• Power supplied equipment can emit electromagnetic waves, that could influence, limit or result in
malfunction of the monitor. Install the equipment in a controlled environment, where such effects are
avoided.
• This is an LCD Monitor intended for use in a medical imaging system.
Classification of Equipment
------
Type of protection against electric shock: Class I
EMC class: EN60601-1-2:2007 Group 1 Class B
Classification of medical device (MDD 93/42/EEC): Class I
Mode of operation: Continuous
IP Class: IPX0
Appendix
53
FCC Declaration of Conformity
For U.S.A. , Canada, etc. (rated 100-120 Vac) Only
FCC Declaration of Conformity
We, the Responsible Party
EIZO Inc.
5710 Warland Drive, Cypress, CA 90630
Phone: (562) 431-5011
declare that the product
Trade name: EIZO
Model: FlexScan T1781
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures.
*
*
*
*
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Note
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep interference
within the limits of a Class B digital device.
- AC Cord
- Shielded Signal Cable (enclosed)
Canadian Notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.
54
Appendix
EMC Information
Essential performance of FlexScan T1781 is to display images and operate functions normally.
CAUTION
The FlexScan T1781 requires special precautions regarding EMC and need to be installed, put into
service and used according to the following information.
Do not use any cables other than the cables that provided or specified by us.
Using other cables may cause the increase of emission or decrease of immunity.
Cable Length: Max. 2m
Do not put any portable and mobile RF communications equipment close to the FlexScan T1781.
Doing so may affect the FlexScan T1781.
The FlexScan T1781 should not be used adjacent to or stacked with other equipment. If adjacent or
stacked use is necessary, the equipment or system should be observed to verify normal operation
in the configuration in which it will be used.
Anyone who connects additional equipment to the signal input part or signal output parts,
configuring a medical system, is responsible that the system complies with the requirements of IEC/
EN60601-1-2.
Guidance and manufacturer’s declaration - electromagnetic emissions
The FlexScan T1781 is intended for use in the electromagnetic environment specified below.
The customer or the user of the FlexScan T1781 should assure that it is used in such an environment.
Emission test
RF emissions
CISPR11/EN55011
Compliance Electromagnetic environment - guidance
Group 1
RF emissions
Class B
CISPR11/EN55011
Harmonic emissions Class D
IEC/EN61000-3-2
Voltage fluctuations / Complies
flicker emissions
IEC/EN61000-3-3
The FlexScan T1781 uses RF energy only for its internal function.
Therefore, its RF emission are very low and are not likely to cause any
interference in nearby electronic equipment.
The FlexScan T1781 is suitable for use in all establishments, including domestic
establishments and those directly connected to the public low-voltage power
supply network that supplies buildings used for domestic purposes.
Guidance and manufacturer’s declaration - electromagnetic immunity
The FlexScan T1781 is intended for use in the electromagnetic environment specified below.
The customer or the user of the FlexScan T1781 should assure that it is used in such an environment.
Immunity test
Electrostatic
discharge (ESD)
IEC/EN61000-4-2
Electrical fast
transient / burst
IEC/EN61000-4-4
Surge
IEC/EN61000-4-5
Voltage dips, short
interruptions and
voltage variations on
power supply input
lines
IEC/EN61000-4-11
IEC/EN60601 test
level
Compliance level
Electromagnetic environment - guidance
±6kV contact
±8kV air
±6kV contact
±8kV air
Floors should be wood, concrete or ceramic tile.
If floors are covered with synthetic material, the
relative humidity should be at least 30%.
±2kV
for power supply lines
±1kV
for input/output lines
±1kV line(s) to line(s)
±2kV line(s) to earth
±2kV
for power supply lines
±1kV
for input/output lines
±1kV line(s) to line(s)
±2kV line(s) to earth
Mains power quality should be that of a typical
commercial or hospital environment.
<5% UT (>95% dip in
UT) for 0.5 cycle
40% UT (60% dip in UT)
for 5 cycles
70% UT (30% dip in UT)
for 25 cycles
<5% UT (>95% dip in
UT) for 5sec
3A/m
<5% UT (>95% dip in
UT) for 0.5 cycle
40% UT (60% dip in
UT) for 5 cycles
70% UT (30% dip in
UT) for 25 cycles
<5% UT (>95% dip in
UT) for 5sec
3A/m
Mains power quality should be that of a typical
commercial or hospital environment. If the
user of the FlexScan T1781 requires continued
operation during power mains interruptions, it
is recommended that the FlexScan T1781 be
powered from an uninterruptible power supply or
a battery.
Mains power quality should be that of a typical
commercial or hospital environment.
Power frequency magnetic fields should be at
Power frequency
levels characteristic of a typical location in a
(50/60Hz)
typical commercial or hospital environment.
magnetic field
IEC/EN61000-4-8
NOTE UT is the a.c. mains voltage prior to application of the test level.
Appendix
55
Guidance and manufacturer’s declaration - electromagnetic immunity
The FlexScan T1781 is intended for use in the electromagnetic environment specified below. The customer or the user
of the FlexScan T1781 should assure that it is used in such an environment.
Immunity test
Conducted RF
IEC/EN61000-4-6
Radiated RF
IEC/EN61000-4-3
IEC/EN60601 test
level
Compliance level
Electromagnetic environment - guidance
3Vrms
150kHz to 80MHz
3Vrms
3V/m
80MHz to 2.5GHz
3V/m
Portable and mobile RF communications
equipment should be used no closer to any part
of the FlexScan T1781, including cables, than
the recommended separation distance calculated
from the equation applicable to the frequency of
the transmitter.
Recommended Separation distance
d = 1.2 √ P
d = 1.2 √ P, 80MHz to 800MHz
d = 2.3 √ P, 800MHz to 2.5GHz
Where “P” is the maximum output power rating
of the transmitter in watts (W) according to
the transmitter manufacturer and “d” is the
recommended separation distance in meters (m).
Field strengths from fixed RF transmitters, as
determined by an electromagnetic site surveya,
should be less than the compliance level in each
frequency rangeb.
Interference may occur in the vicinity of equipment
marked with the following symbol.
NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.
a
Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile
radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy.
To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be
considered. If the measured field strength in the location in which the FlexScan T1781 is used exceeds the applicable
RF compliance level above, the FlexScan T1781 should be observed to verify normal operation. If abnormal performance
is observed, additional measures may be necessary, such as reorienting or relocating the FlexScan T1781.
b
Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.
56
Appendix
Recommended separation distances between portable and mobile RF communications equipment
and the FlexScan T1781
The FlexScan T1781 is intended for use in an electromagnetic environment in which radiated RF disturbances
are controlled. The customer or the user of the FlexScan T1781 can help prevent electromagnetic interference by
maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the
FlexScan T1781 as recommended below, according to the maximum output power of the communications equipment.
Separation distance according to frequency of transmitter
Rated maximum output
m
power of transmitter
150kHz to 80MHz
80MHz to 800MHz
800MHz to 2.5GHz
W
d = 1.2 √ P
d = 1.2 √ P
d = 2.3 √ P
0.01
0.12
0.12
0.23
0.1
0.38
0.38
0.73
1
1.2
1.2
2.3
10
3.8
3.8
7.3
100
12
12
23
For transmitters rated at a maximum output power not listed above, the recommended separation distance “d” in meters
(m) can be estimated using the equation applicable to the frequency of the transmitter, where “P” is the maximum
output power rating of the transmitter in watts (W) according to the transmitter manufacturer.
NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.
Appendix
57
LIMITED WARRANTY
LIMITED WARRANTY
EIZO Corporation (hereinafter referred to as “EIZO”) and distributors authorized by EIZO (hereinafter referred to as the
“Distributors”) warrant, subject to and in accordance with the terms of this limited warranty (hereinafter referred to as the
“Warranty”), to the original purchaser (hereinafter referred to as the “Original Purchaser”) who purchased the product
specified in this document (hereinafter referred to as the “Product”) from EIZO or Distributors, that EIZO and Distributors
shall, at their sole discretion, either repair or replace the Product at no charge if the Original Purchaser becomes aware
within the Warranty Period (defined below) that the Product malfunctions or is damaged in the course of normal use of
the Product in accordance with the description in the instruction manual attached to the Product (hereinafter referred to
as the “User’s Manual”).
The period of this Warranty is three (3) years from the date of purchase of the Product (hereinafter referred to as the
“Warranty Period”). EIZO and Distributors shall bear no liability or obligation with regard to the Product in relation to the
Original Purchaser or any third parties other than as provided under this Warranty.
EIZO and Distributors will cease to hold or store any parts (excluding design parts) of the Product upon expiration of
seven (7) years after the production of such parts is discontinued. In repairing the monitor, EIZO and Distributors will use
renewal parts which comply with our QC standards. If the unit cannot be repaired due to its condition or the stockout of
a relevant part, EIZO and Distributors may offer the replacement by a product with equivalent performance instead of
repairing it.
The Warranty is valid only in the countries or territories where the Distributors are located. The Warranty does not restrict
any legal rights of the Original Purchaser.
Notwithstanding any other provision of this Warranty, EIZO and Distributors shall have no obligation under this Warranty
whatsoever in any of the cases as set forth below:
(a) Any defect of the Product caused by freight damage, modification, alteration, abuse, misuse, accident, incorrect
installation, disaster, faulty maintenance and/or improper repair by third party other than EIZO and Distributors;
(b) Any incompatibility of the Product due to possible technical innovations and/or regulations;
(c) Any deterioration of the sensor;
(d) Any deterioration of display performance caused by the deterioration of expendable parts such as the LCD panel
and/or backlight, etc. (e.g. changes in brightness, changes in brightness uniformity, changes in color, changes in
color uniformity, defects in pixels including burnt pixels, etc.);
(e) Any defect of the Product caused by external equipment;
(f) Any defect of the Product on which the original serial number has been altered or removed;
(g) Any normal deterioration of the product, particularly that of consumables, accessories, and/or attachments (e.g.
buttons, rotating parts, cables, User’s Manual, etc.); and
(h) Any deformation, discoloration, and/or warp of the exterior of the product including that of the surface of the LCD
panel.
To obtain service under the Warranty, the Original Purchaser must deliver the Product, freight prepaid, in its original
package or other adequate package affording an equal degree of protection, assuming the risk of damage and/or loss
in transit, to the local Distributor. The Original Purchaser must present proof of purchase of the Product and the date of
such purchase when requesting services under the Warranty.
The Warranty Period for any replaced and/or repaired product under this Warranty shall expire at the end of the original
Warranty Period.
EIZO OR DISTRIBUTORS ARE NOT RESPONSIBLE FOR ANY DAMAGE TO, OR LOSS OF, DATA OR OTHER
INFORMATION STORED IN ANY MEDIA OR ANY PART OF ANY PRODUCT RETURNED TO EIZO OR DISTRIBUTORS
FOR REPAIR.
EIZO AND DISTRIBUTORS MAKE NO FURTHER WARRANTIES, EXPRESSED OR IMPLIED, WITH RESPECT TO
THE PRODUCT AND ITS QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR
USE. IN NO EVENT SHALL EIZO OR DISTRIBUTORS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL,
CONSEQUENTIAL OR OTHER DAMAGE WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR
LOSS OF PROFIT, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR ANY OTHER PECUNIARY
LOSS) ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT OR IN ANY CONNECTION WITH THE
PRODUCT, WHETHER BASED ON CONTRACT, TORT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, EVEN
IF EIZO OR DISTRIBUTORS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THIS EXCLUSION
ALSO INCLUDES ANY LIABILITY WHICH MAY ARISE OUT OF THIRD PARTY CLAIMS AGAINST THE ORIGINAL
PURCHASER. THE ESSENCE OF THIS PROVISION IS TO LIMIT THE POTENTIAL LIABILITY OF EIZO AND
DISTRIBUTORS ARISING OUT OF THIS LIMITED WARRANTY AND/OR SALES.
58
Appendix
BEGRENZTE GARANTIE
EIZO Corporation (im Weiteren als „EIZO“ bezeichnet) und die Vertragsimporteure von EIZO (im Weiteren als
„Vertrieb(e)“ bezeichnet) garantieren dem ursprünglichen Käufer (im Weiteren als „Erstkäufer“ bezeichnet), der das in
diesem Dokument vorgegebene Produkt (im Weiteren als „Produkt“ bezeichnet) von EIZO oder einem Vertrieb erworben
hat, gemäß den Bedingungen dieser beschränkten Garantie (im Weiteren als „Garantie“ bezeichnet), dass EIZO und
der Vertrieb nach eigenem Ermessen das Produkt entweder kostenlos reparieren oder austauschen, falls der Erstkäufer
innerhalb der Garantiefrist (weiter unten festgelegt) eine Fehlfunktion bzw. Beschädigung des Produkts feststellt,
die während des normalen Gebrauchs des Produkts gemäß den Anweisungen des zum Lieferumfang des Produkts
gehörenden Benutzerhandbuchs (im Weiteren als „Benutzerhandbuch“ bezeichnet) aufgetreten ist.
Die Dauer der Garantieleistung (im Weiteren als „Garantiefrist“ bezeichnet) beträgt drei (3) Jahre ab dem Kaufdatum
des Produkts. EIZO und die Vertriebe übernehmen über den Rahmen dieser Garantie hinaus hinsichtlich des Produkts
keinerlei Haftung oder Verpflichtung dem Erstkäufer oder Dritten gegenüber.
Nach Ablauf von sieben (7) Jahren nach Ende der Produktion solcher Teile werden EIZO und Vertriebshändler keine
Teile (mit Ausnahme von Konstruktionsteilen) mehr vorhalten und lagern. EIZO und seine Vertriebspartner verpflichten
sich, bei einer etwaigen Reparatur des Monitors ausschließlich Produkte gemäß den EIZO-Qualitätssicherungsstandards
zu verwenden. Wenn das Gerät aufgrund seines Zustands oder eines Fehlbestands bei einem entsprechenden Teil nicht
repariert werden kann, können EIZO und Vertriebshändler statt der Reparatur des Geräts den Austausch gegen ein
Produkt mit gleichwertiger Leistung anbieten.
Diese Garantie gilt nur in Ländern oder Gebieten, in denen sich Vertriebe befinden. Die gesetzlichen
Gewährleistungsrechte des Erstkäufers gegenüber dem Verkäufer werden durch diese Garantie nicht berührt.
EIZO und die Vertriebe besitzen im Rahmen dieser Garantie keinerlei Verpflichtung in den folgenden Fällen:
(a) Produktdefekte, die auf Frachtschäden, Modifikation, Nachgestaltung, Missbrauch, Fehlbedienung, Unfälle,
unsachgemäße Installation, Naturkatastrophen, fehlerhafte Wartung und/oder unsachgemäße Reparatur durch eine
andere Partei als EIZO und die Vertriebe zurückzuführen sind.
(b) Eine Inkompatibilität des Produkts aufgrund von technischen Neuerungen und/oder neuen Bestimmungen, die
nach dem Kauf in Kraft treten.
(c) Jegliche Verschlechterung des Sensors.
(d) Jegliche Verschlechterung der Bildschirmleistung, die durch Verschleißteile wie das LCD-Panel und/oder die
Hintergrundbeleuchtung usw. hervorgerufen werden (z.B. Veränderungen von Helligkeit oder Helligkeitsverteilung,
Veränderungen von Farbe oder Farbverteilung, Pixeldefekte einschließlich von durchgebrannten Pixeln usw.).
(e) Produktdefekte, die durch externe Geräte verursacht werden.
(f) Jeglicher Defekt eines Produkts, dessen ursprüngliche Seriennummer geändert oder entfernt wurde.
(g) Normale Abnutzung des Produkts, insbesondere von Verbrauchsteilen, Zubehörteilen und/oder Beilagen (z.B.
Tasten, drehbare Teile, Kabel, Benutzerhandbuch usw.); sowie
(h) Verformungen, Verfärbungen und/oder Verziehungen am Produktäußeren, einschließlich der Oberfläche des LCDPanels.
Bei Inanspruchnahme der Garantieleistung ist der Erstkäufer verpflichtet, das Produkt auf eigene Kosten und
in der Originalverpackung bzw. einer anderen geeigneten Verpackung, die einen gleichwertigen Schutz gegen
Transportschäden bietet, an den örtlichen Vertrieb zu übersenden, wobei der Erstkäufer das Transportrisiko gegenüber
Schäden und/oder Verlust trägt. Zum Zeitpunkt der Inanspruchnahme der Garantieleistung muss der Erstkäufer einen
Verkaufsbeleg vorweisen, auf dem das Kaufdatum angegeben ist.
Die Garantiefrist für ein im Rahmen dieser Garantie ausgetauschtes und/oder repariertes Produkt erlischt nach Ablauf
der ursprünglichen Garantiefrist.
EIZO ODER DIE EIZO-VERTRAGSIMPORTEURE HAFTEN NICHT FÜR ZERSTÖRTE DATENBESTÄNDE ODER DIE
KOSTEN DER WIEDERBESCHAFFUNG DIESER DATENBESTÄNDE AUF JEGLICHEN DATENTRÄGERN ODER
TEILEN DES PRODUKTS, DIE IM RAHMEN DER GARANTIE BEI EIZO ODER DEN EIZO-VERTRAGSIMPORTEUREN
ZUR REPARATUR EINGEREICHT WURDEN.
EIZO UND DIE EIZO-VERTRAGSIMPORTEURE GEBEN WEDER EXPLIZITE NOCH IMPLIZITE GARANTIEN
IN BEZUG AUF DIESES PRODUKT UND SEINE QUALITÄT, LEISTUNG, VERKÄUFLICHKEIT ODER EIGNUNG
FÜR EINEN BESTIMMTEN ZWECK. AUF KEINEN FALL SIND EIZO ODER DIE EIZO-VERTRAGSIMPORTEURE
VERANTWORTLICH FÜR JEGLICHE ZUFÄLLIGE, INDIREKTE, SPEZIELLE, FOLGE- ODER ANDERE SCHÄDEN
JEGLICHER ART (EINSCHLIESSLICH OHNE JEDE BEGRENZUNG SCHÄDEN BEZÜGLICH PROFITVERLUST,
GESCHÄFTSUNTERBRECHUNG, VERLUST VON GESCHÄFTSINFORMATION ODER JEGLICHE ANDEREN
FINANZIELLEN EINBUSSEN), DIE DURCH DIE VERWENDUNG DES PRODUKTES ODER DIE UNFÄHIGKEIT
ZUR VERWENDUNG DES PRODUKTES ODER IN JEGLICHER BEZIEHUNG MIT DEM PRODUKT, SEI ES
BASIEREND AUF VERTRAG, SCHADENSERSATZ, NACHLAESSIGKEIT, STRIKTE HAFTPFLICHT ODER ANDEREN
FORDERUNGEN ENTSTEHEN, AUCH WENN EIZO UND DIE EIZO-VERTRAGSIMPORTEURE IM VORAUS ÜBER
DIE MÖGLICHKEIT SOLCHER SCHÄDEN INFORMIERT WURDEN. DIESER AUSSCHLUSS ENTHÄLT AUCH JEDE
HAFTPFLICHT, DIE AUS FORDERUNGEN DRITTER GEGEN DEN ERSTKÄUFER ENTSTEHEN KANN. ZWECK
DIESER KLAUSEL IST ES, DIE HAFTUNG VON EIZO UND DEN VERTRIEBEN GEGENÜBER FORDERUNGEN ZU
BEGRENZEN, DIE AUS DIESER BESCHRÄNKTEN GARANTIE UND/ODER DEM VERKAUF ENTSTEHEN KÖNNEN.
Appendix
59
GARANTIE LIMITÉE
EIZO Corporation (ci-après dénommé « EIZO ») et les distributeurs autorisés par EIZO (ci-après dénommés
« Distributeurs »), sous réserve et conformément aux termes de cette garantie limitée (ci-après dénommée
« Garantie »), garantissent à l’acheteur initial (ci-après dénommé « Acheteur initial ») du produit spécifié dans la
présente (ci-après dénommé « Produit ») acheté auprès d’EIZO ou de Distributeurs agréés EIZO, que EIZO et ses
Distributeurs auront pour option de réparer ou remplacer gratuitement le Produit si l’Acheteur initial constate, pendant la
Période de garantie (définie ci-dessous), qu’il y a un dysfonctionnement ou que le Produit a subi un dommage dans le
cadre d’une utilisation normale du Produit conformément à la description du mode d’emploi qui accompagne le Produit
(ci-après dénommé « Manuel d’utilisation »).
La période de cette Garantie est de trois (3) ans à partir de la date d’achat du Produit (ci-après dénommée « Période de
Garantie »). EIZO et ses Distributeurs déclinent toute responsabilité ou obligation concernant ce Produit face à l’Acheteur
initial ou à toute autre personne à l’exception de celles stipulées dans la présente Garantie.
EIZO et ses Distributeurs cesseront de conserver ou de stocker des pièces (à l'exception des pièces de conception) du
Produit à l'expiration d'une période de sept (7) ans après l'arrêt de la production de ces pièces. Pour réparer le moniteur,
EIZO et ses distributeurs utiliseront des pièces de rechange conformes à nos normes de contrôle qualité. Si l'unité ne
peut pas être réparée en raison de son état ou de la rupture de stock d'une pièce adéquate, EIZO et ses Distributeurs
peuvent proposer le remplacement par un produit aux performances équivalentes au lieu de le réparer.
La Garantie est valable uniquement dans les pays ou les territoires où se trouvent les Distributeurs. La Garantie ne limite
aucun des droits reconnus par la loi à l’Acheteur initial.
Nonobstant toute autre clause de cette Garantie, EIZO et ses Distributeurs n’auront d’obligation dans le cadre de cette
Garantie pour aucun des cas énumérés ci-dessous :
(a) Tout défaut du Produit résultant de dommages occasionnés lors du transport, d’une modification, d’une altération,
d’un abus, d’une mauvaise utilisation, d’un accident, d’une installation incorrecte, d’un désastre, d’un entretien et/
ou d’une réparation incorrects effectués par une personne autre que EIZO ou ses Distributeurs ;
(b) Toute incompatibilité du Produit résultant d’améliorations techniques et/ou réglementations possibles ;
(c) Toute détérioration du capteur ;
(d) Toute détérioration des performances d’affichage causée par la détérioration des éléments consommables tels
que le panneau LCD et/ou le rétroéclairage, etc. (par exemple des changements de luminosité, des changements
de l’uniformité de la luminosité, des modifications de couleur, des changements de l’uniformité des couleurs, des
défectuosités de pixels y compris des pixels brûlés, etc.);
(e) Tout défaut du Produit causé par un appareil externe ;
(f) Tout défaut d’un Produit sur lequel le numéro de série original a été altéré ou supprimé ;
(g) Toute détérioration normale du Produit, particulièrement celle des consommables, des accessoires et/ou des
pièces reliées au Produit (touches, éléments pivotants, câbles, Manuel d’utilisation etc.), et
(h) Toute déformation, décoloration, et/ou gondolage de l’extérieur du Produit, y compris celle de la surface du
panneau LCD.
Pour bénéficier d’un service dans le cadre de cette Garantie, l’Acheteur initial doit renvoyer le Produit port payé, dans
son emballage d’origine ou tout autre emballage approprié offrant un degré de protection équivalent, au Distributeur local,
et assumera la responsabilité des dommages et/ou perte possibles lors du transport. L’Acheteur initial doit présenter une
preuve d’achat du Produit comprenant sa date d’achat pour bénéficier de ce service dans le cadre de la Garantie.
La Période de garantie pour tout Produit remplacé et/ou réparé dans le cadre de cette Garantie expirera à la fin de la
Période de garantie initiale.
EIZO OU SES DISTRIBUTEURS NE SAURAIENT ÊTRE TENUS RESPONSABLES DES DOMMAGES OU PERTES DE
DONNÉES OU D’AUTRES INFORMATIONS STOCKÉES DANS UN MÉDIA QUELCONQUE OU UNE AUTRE PARTIE
DU PRODUIT RENVOYÉ À EIZO OU AUX DISTRIBUTEURS POUR RÉPARATION.
AUCUNE AUTRE GARANTIE, EXPLICITE OU TACITE, N’EST OFFERTE PAR EIZO ET SES DISTRIBUTEURS
CONCERNANT LE PRODUIT ET SES QUALITÉS, PERFORMANCES, QUALITÉ MARCHANDE OU ADAPTATION
À UN USAGE PARTICULIER. EN AUCUN CAS, EIZO OU SES DISTRIBUTEURS NE SERONT RESPONSABLES
DES DOMMAGES FORTUITS, INDIRECTS, SPÉCIAUX, INDUITS, OU DE TOUT AUTRE DOMMAGE QUEL
QU’IL SOIT (Y COMPRIS, SANS LIMITATION, LES DOMMAGES RÉSULTANT D’UNE PERTE DE PROFIT, D’UNE
INTERRUPTION D’ACTIVITÉS, D’UNE PERTE DE DONNÉES COMMERCIALES, OU DE TOUT AUTRE MANQUE
À GAGNER) RÉSULTANT DE L’UTILISATION OU DE L’INCAPACITÉ D’UTILISER LE PRODUIT OU AYANT UN
RAPPORT QUELCONQUE AVEC LE PRODUIT, QUE CE SOIT SUR LA BASE D’UN CONTRAT, D’UN TORT, D’UNE
NÉGLIGENCE, D’UNE RESPONSABILITÉ STRICTE OU AUTRE, MÊME SI EIZO OU SES DISTRIBUTEURS ONT ÉTÉ
AVERTIS DE LA POSSIBILITÉ DE TELS DOMMAGES. CETTE LIMITATION INCLUT AUSSI TOUTE RESPONSABILITÉ
QUI POURRAIT ÊTRE SOULEVÉE LORS DES RÉCLAMATIONS D’UN TIERS CONTRE L’ACHETEUR INITIAL.
L’ESSENCE DE CETTE CLAUSE EST DE LIMITER LA RESPONSABILITÉ POTENTIELLE DE EIZO ET DE SES
DISTRIBUTEURS RÉSULTANT DE CETTE GARANTIE LIMITÉE ET/OU DES VENTES.
60
Appendix
GARANTÍA LIMITADA
EIZO Corporation (en lo sucesivo “EIZO”) y sus distribuidores autorizados (en lo sucesivo los “Distribuidores”),EIZO Corpora
con arreglo y de conformidad con los términos de esta garantía limitada (en lo sucesivo la “Garantía”), garantizan alriferimento da
comprador original (en lo sucesivo el “Comprador original”) que compró el producto especificado en este documento (enriferimento da
lo sucesivo el “Producto”) a EIZO o a sus Distribuidores, que EIZO y sus Distribuidores, a su propio criterio, repararánoriginale”) ch
o sustituirán el Producto de forma gratuita si el Comprador original detecta dentro del periodo de la Garantía (indicado“Prodotto”) da
posteriormente) que el Producto no funciona correctamente o que se ha averiado durante el uso normal del mismo deProdotto senz
acuerdo con las indicaciones del manual de instrucciones suministrado con el Producto (en lo sucesivo el “Manual delmalfunziona e
allegato al Pro
usuario”).
El periodo de esta Garantía es de tres (3) años a partir de la fecha de compra del Producto (en adelante designado comoIl periodo di qu
el “Periodo de Garantía”). EIZO y sus Distribuidores no tendrán ninguna responsabilidad ni obligación con respecto alcon “Periodo d
riguardo al Pro
Producto para con el Comprador original ni con terceros que no sean las estipuladas en la presente Garantía.
EIZO y sus distribuidores dejarán de tener o almacenar cualquier pieza del producto (excepto piezas del diseño) una vezEIZO e i distri
expirado el periodo de siete (7) años después de que hayan dejado de fabricarse tales piezas. Para la reparación delsette (7) anni
monitor, EIZO y los distribuidores utilizarán repuestos que cumplan con nuestros estándares de control de calidad. Si noutilizzeranno p
se puede reparar la unidad debido a su estado o si se han agotado las existencias de una pieza importante, EIZO y suscausa delle su
sostituzione co
distribuidores podrían ofrecerle sustituirlo por un producto con rendimiento equivalente en lugar de repararlo.
La Garantía es válida sólo en los países y territorios donde están ubicados los Distribuidores. La Garantía no restringeLa Garanzia è
dell’Acquirente
ningún derecho legal del Comprador original.
A pesar de las estipulaciones de esta Garantía, EIZO y sus Distribuidores no tendrán obligación alguna bajo estaIndipendentem
derivante da q
Garantía en ninguno de los casos expuestos a continuación:
(a) Cualquier defecto del Producto causado por daños en el transporte, modificación, alteración, abuso, uso incorrecto, (a) Qualsias
installazi
accidente, instalación incorrecta, desastre, mantenimiento incorrecto y/o reparación indebida realizada por un
tercero que no sea EIZO o sus Distribuidores.
EIZO o i
(b) Cualquier incompatibilidad del Producto debida a posibles innovaciones técnicas y/o reglamentaciones.
(b) Qualsias
(c) Cualquier deterioro del sensor.
(c) Qualsias
(d) Cualquier deterioro en el rendimiento de la visualización causado por fallos en las piezas consumibles como el (d) Qualsias
panel LCD y/o la "Backlight", etc. (p. ej. cambios de brillo, cambios de uniformidad del brillo, cambios de color,
il pannell
cambios de uniformidad del color, defectos de píxeles, incluyendo píxeles muertos, etc.).
della lum
bruciati, e
(e) Cualquier defecto del Producto causado por un equipo externo.
(e) Qualsias
(f) Cualquier defecto del Producto en el que haya sido alterado o borrado el número de serie original.
(g) Cualquier deterioro normal del Producto, y en particular de las piezas consumibles, accesorios y demás (p. ej. (f) Qualsias
botones, piezas giratorias, cables, Manual del usuario, etc.).
(g) Qualsias
attacchi (
(h) Cualquier deformación, decoloración y/o alabeo del exterior del Producto incluida la superficie del panel LCD.
Para obtener servicio en los términos de esta Garantía, el Producto deberá ser enviado por el Comprador original, (h) Qualsias
LCD.
a su Distribuidor local, con el transporte previamente pagado, en el embalaje original u otro embalaje adecuado que
ofrezca el mismo grado de protección, asumiendo el riesgo de daños y/o pérdida del Producto durante el transporte. ElPer ricevere a
Comprador original deberá presentar un comprobante de compra del Producto en el que se refleje la fecha de comprapre-pagato, ne
del mismo cuando lo solicite el servicio de Garantía.
assumendosi
El Periodo de garantía para cualquier Producto reemplazado y/o reparado en los términos de esta Garantía expirará alprova di acquis
vencer el Periodo de garantía original.
Il Periodo di g
EIZO O LOS DISTRIBUIDORES AUTORIZADOS DE EIZO NO SE RESPONSABILIZAN DE NINGÚN DAÑO Ogaranzia origin
PÉRDIDA QUE PUEDAN SUFRIR LOS DATOS U OTRA INFORMACIÓN ALMACENADA EN CUALQUIER MEDIO OEIZO O I SUO
CUALQUIER PARTE DE CUALQUIER PRODUCTO DEVUELTO A EIZO O A LOS DISTRIBUIDORES DE EIZO PARAINFORMAZIO
SU REPARACIÓN.
INVIATO A EIZ
EIZO Y LOS DISTRIBUIDORES AUTORIZADOS DE EIZO NO OFRECEN NINGUNA OTRA GARANTÍA, IMPLÍCITAEIZO E I SUO
NI EXPLÍCITA, CON RESPECTO AL PRODUCTO Y A SU CALIDAD, RENDIMIENTO, COMERCIABILIDAD ERIGUARDO I
IDONEIDAD PARA CUALQUIER USO EN PARTICULAR. EN NINGÚN CASO SERÁN EIZO O LOS DISTRIBUIDORESQUALSIASI U
AUTORIZADOS DE EIZO RESPONSABLES DE NINGÚN DAÑO EMERGENTE, INDIRECTO, ESPECIAL, INHERENTERESPONSAB
O CUALQUIERA QUE SEA (INCLUYENDO, SIN LIMITACIÓN, DAÑOS POR LUCRO CESANTE, INTERRUPCIÓNQUALSIASI AL
DE LA ACTIVIDAD COMERCIAL, PÉRDIDA DE INFORMACIÓN COMERCIAL O CUALQUIER OTRA PÉRDIDAATTIVITÀ, PE
PECUNIARIA) QUE SE DERIVE DEL USO O IMPOSIBILIDAD DE USO DEL PRODUCTO O EN RELACIÓN CON ELDALL’USO O
PRODUCTO, YA SEA BASADO EN CONTRATO, POR AGRAVIO, NEGLIGENCIA, ESTRICTA RESPONSABILIDADSIA SU BASE
O CUALQUIERA QUE SEA, AUN CUANDO SE HAYA ADVERTIDO A EIZO O A LOS DISTRIBUIDORES DE EIZOSE EIZO O I
DE LA POSIBILIDAD DE TALES DAÑOS. ESTA EXCLUSIÓN TAMBIÉN ABARCA CUALQUIER RESPONSABILIDADQUESTA ESC
QUE PUEDA DERIVARSE DE RECLAMACIONES HECHAS POR UN TERCERO CONTRA EL COMPRADORDI TERZI CO
ORIGINAL. LA ESENCIA DE ESTA ESTIPULACIÓN ES LIMITAR LA RESPONSABILIDAD POTENCIAL DE EIZO Y LOSRESPONSABI
DISTRIBUIDORES QUE PUDIERA DERIVARSE DE ESTA GARANTÍA LIMITADA Y/O VENTAS.
DALLE VENDI
Appendix
61
GARANZIA LIMITATA
EIZO Corporation (a cui si farà riferimento da qui in poi con “EIZO”) ed i Distributori autorizzati da EIZO (a cui si farà
riferimento da qui in poi con “Distributori”) garantiscono, secondo i termini di questa garanzia limitata (a cui si farà
riferimento da qui in poi con “Garanzia”) all’acquirente originale (a cui si farà riferimento da qui in poi con “Acquirente
originale”) che ha acquistato il prodotto specificato in questo documento (a cui si farà riferimento da qui in poi con
“Prodotto”) da EIZO o dai suoi Distributori, che EIZO e i distributori, a loro discrezione, ripareranno o sostituiranno il
Prodotto senza addebito se l’Acquirente originale trova, entro il periodo della Garanzia (definito sotto), che il Prodotto
malfunziona e si è danneggiato nel corso del suo normale utilizzo osservando le indicazioni del manuale di istruzioni
allegato al Prodotto (a cui si farà riferimento da qui in poi con “Manuale utente”).
Il periodo di questa Garanzia è di tre (3) anni dalla data di acquisto del Prodotto (a cui si farà riferimento da qui in poi
con “Periodo di Garanzia”). EIZO e i suoi Distributori non si assumono alcuna responsabilità e non hanno alcun obbligo
riguardo al Prodotto verso l’Acquirente originale o terzi diversi da quelli relativi a questa Garanzia.
EIZO e i distributori cesseranno lo stoccaggio dei componenti (tranne le parti relative al progetto) del prodotto dopo
sette (7) anni dall’interruzione della produzione di tali componenti. Per la riparazione del monitor, EIZO e i Distributori
utilizzeranno parti di ricambio conformi ai nostri standard di controllo della qualità. Se l’unità non può essere riparata a
causa delle sue condizioni o dell’esaurimento scorte di un componente rilevante, EIZO e i distributori potrebbero offrire la
sostituzione con un prodotto con prestazioni equivalenti piuttosto ripararlo.
La Garanzia è valida soltanto nei paesi dove ci sono i Distributori EIZO. La Garanzia non limita alcun diritto legale
dell’Acquirente originale.
Indipendentemente da qualsiasi altra condizione di questa Garanzia, EIZO e i suoi Distributori non avranno alcun obbligo
derivante da questa Garanzia in ognuno dei casi elencati di seguito:
(a) Qualsiasi difetto del Prodotto causato da danni di trasporto, modifiche, alterazioni, abusi, usi impropri, incidenti,
installazione errata, calamità, manutenzione errata e/o riparazioni improprie eseguite da terze parti che non siano
EIZO o i suoi Distributori.
(b) Qualsiasi incompatibilità del Prodotto dovuta a possibili innovazioni tecniche e/o normative.
(c) Qualsiasi deterioramento del sensore.
(d) Qualsiasi deterioramento delle prestazioni dello schermo causato dal deterioramento delle parti consumabili, come
il pannello LCD e/o la retroilluminazione, ecc. (per esempio: i cambiamenti di luminosità, cambiamenti di uniformità
della luminosità, i cambiamenti di colore, i cambiamenti di uniformità del colore, i difetti dei pixel, inclusi i pixel
bruciati, ecc.).
(e) Qualsiasi difetto del Prodotto causato da apparecchiature esterne.
(f) Qualsiasi difetto del Prodotto in cui il numero di serie originale sia stato alterato o rimosso.
(g) Qualsiasi normale deterioramento del Prodotto, in particolar modo nelle sue parti di consumo, accessori, e/o
attacchi (per esempio: tasti, parti rotanti, cavi, Manuale dell’utente, ecc.).
(h) Qualsiasi tipo di deformazione, scolorimento, e/o di involucro esterno del Prodotto inclusa la superficie del pannello
LCD.
Per ricevere assistenza tecnica con questa Garanzia, l’Acquirente originale deve inviare il Prodotto, con trasporto
pre-pagato, nella sua confezione originale o altra confezione adeguata che fornisce un livello analogo di protezione,
assumendosi il rischio di danni e/o perdita in transito, al Distributore locale. L’Acquirente originale deve presentare la
prova di acquisto che stabilisce la data di acquisto del Prodotto quando richiede servizio sotto Garanzia.
Il Periodo di garanzia per qualsiasi Prodotto sostituito e/o riparato sotto questa Garanzia scade alla fine del Periodo di
garanzia originale.
EIZO O I SUOI DISTRIBUTORI NON SONO RESPONSABILI PER QUALSIASI DANNO O PERDITA DI DATI O ALTRE
INFORMAZIONI MEMORIZZATI SU QUALSIASI SUPPORTO O QUALSIASI PARTE DI QUALSIASI PRODOTTO
INVIATO A EIZO O I SUOI DISTRIBUTORI PER RIPARAZIONI.
EIZO E I SUOI DISTRIBUTORI NON OFFRONO ALCUNA GARANZIA ADDIZIONALE, IMPLICITA O ESPLICITA,
RIGUARDO IL PRODOTTO E LA SUA QUALITÀ, PRESTAZIONI, VENDIBILITÀ O APPROPRIATEZZA PER
QUALSIASI USO PARTICOLARE. IN NESSUN CASO EIZO O I DISTRIBUTORI EIZO AUTORIZZATI SARANNO
RESPONSABILI PER QUALSIASI DANNO ACCIDENTALE, INDIRETTO, SPECIALE, CONSEGUENTE O DI
QUALSIASI ALTRA NATURA (INCLUSI, SENZA LIMITI, DANNI PER PERDITA DI PROFITTI, INTERRUZIONE DELLE
ATTIVITÀ, PERDITA DI INFORMAZIONI D’AFFARI O QUALSIASI ALTRA PERDITA PECUNIARIA) DERIVANTI
DALL’USO O DALL’IMPOSSIBILITÀ DI USARE IL PRODOTTO O IN QUALSIASI RELAZIONE AL PRODOTTO,
SIA SU BASE DI CONTRATTO, TORTO, NEGLIGENZA, STRETTA RESPONSABILITÀ O ALTRIMENTI, ANCHE
SE EIZO O I DISTRIBUTORI EIZO AUTORIZZATI SONO STATI AVVERTITI DELLA POSSIBILITÀ DI TALI DANNI.
QUESTA ESCLUSIONE INCLUDE ANCHE QUALSIASI RESPONSABILITÀ CHE POSSA INSORGERE DA RECLAMI
DI TERZI CONTRO L’ACQUIRENTE ORIGINALE. L’ESSENZA DI QUESTO PROVVEDIMENTO È LIMITARE LA
RESPONSABILITÀ POTENZIALE DI EIZO E DEI DISTRIBUTORI DERIVANTE DA QUESTA GARANZIA LIMITATA E/O
DALLE VENDITE.
62
Appendix
BEGRÄNSAD GARANTI
EIZO Corporation (nedan kallat “EIZO”) och EIZOs auktoriserade distributörer (nedan kallade “Distributörer”) garanterar
i enlighet med villkoren i denna begränsade garanti (nedan kallad “Garantin”) den ursprunglige köparen (nedan kallad
den “Ursprunglige köparen”) som köpte den i dokumentet specificerade produkten (nedan kallad “Produkten”) från
EIZO eller Distributörer, att EIZO eller Distributörer enligt eget gottfinnande kostnadsfritt antingen reparera eller byta ut
den defekta Produkten om den Ursprunglige köparen inom Garantiperioden (definieras nedan) upptäcker att Produkten
fungerar felaktigt eller skadas under normal användning av Produkten i enlighet med beskrivningen i bruksanvisningen
(nedan kallad “Bruksanvisning”).
Garantiperioden är begränsad till tre (3) år från datumet för Produktens inköp (häri kallad “Garantiperioden”). EIZO och
Distributörer ska inte under några villkor ha något annat ansvar än vad som anges i denna garanti gällande Produkten i
relation till den Ursprunglige köparen eller tredje part.
EIZO och dess leverantörer slutar lagerföra delar (utom designdelar) till produkten sju (7) år efter att delen i fråga slutar
tillverkas. Nät skärmen repareras använder EIZO och distributörer reservdelar som uppfyller våra kvalitetsstandarder.
Om enheten inte kan repareras på grund av skicket eller att en del inte finns i lager kan EIZO och dess leverantörer
erbjuda sig att byta ut produkten mot en produkt med likvärdig prestanda istället för att reparera den.
Garantin är endast giltig i de länder där det finns Distributörer. Garantin begränsar inte några av den Ursprunglige
köparens lagstadgade rättigheter.
Oavsett andra villkor i denna garanti ska inte EIZO Distributörer under några villkor ha något ansvar i något av de fall
som beskrivs nedan:
(a) När någon bristfällighet hos Produkten kan härledas till att ha uppstått vid frakt, modifiering, ändring, felaktigt
handhavande, olycka, felaktig installation, katastrof, felaktigt underhåll och/eller felaktig reparation utförd av tredje
part annan än EIZO och Distributörer.
(b) Alla former av inkompatibilitet hos Produkten på grund av möjliga tekniska innovationer och/eller bestämmelser.
(c) Alla försämringar av sensorn.
(d) Alla försämringar av bildens prestanda beroende på förbrukningsdelar så som LCD-panel och/eller
bakgrundsbelysning etc. (t.ex. ändringar i ljusstyrka, jämnhet i ljusstyrka, färg, färgjämnhet, defekta pixlar och/eller
fast lysande pixlar etc.).
(e) Alla defekter hos Produkten som orsakats av extern utrustning.
(f) Alla defekter hos Produkten på vilken det ursprungliga serienumret har ändrats eller avlägsnats.
(g) All normal försämring av Produkten, speciellt förbrukningsartiklar, tillbehör och/eller yttre delar (t.ex. knappar,
roterande delar, kablar, Bruksanvisningen etc.).
(h) Varje deformation, missfärgning och/eller skevhet av Produktens yttre inklusive ytan på LCD-panelen.
För att erhålla service under denna garanti måste den Ursprunglige köparen (med hänseende till risken för skada
och/eller förlust under transport) leverera Produkten till närmaste Distributör med förebetald frakt, i dess ursprungliga
förpackning eller annan fullgod förpackning som ger likvärdigt skydd. Den Ursprunglige köparen måste kunna visa
inköpsbevis för Produkten som klargör Produktens inköpsdatum vid begäran av garantiservice.
Garantiperioden för alla utbytta och/eller reparerade produkter under denna garanti skall upphöra vid utgången av den
ursprungliga Garantiperioden.
EIZO ELLER DISTRIBUTÖRER ÄR INTE ANSVARIGA FÖR NÅGON FORM AV SKADA ELLER FÖRLUST AV DATA
ELLER ANNAN INFORMATION SOM HAR LAGRATS I NÅGON FORM AV MEDIA ELLER ANNAN DEL AV NÅGON
PRODUKT SOM HAR RETURNERATS TILL EIZO ELLER DISTRIBUTÖRER FÖR REPARATION.
EIZO OCH DISTRIBUTÖRERNA GARANTERAR INGET, UTTRYCKLIGEN ELLER UNDERFÖRSTÅTT, VAD
BETRÄFFAR PRODUKTEN OCH DESS KVALITET, PRESTANDA, SÄLJBARHET ELLER LÄMPLIGHET FÖR NÅGON
FORM AV SPECIELL ANVÄNDNING. UNDER INGA OMSTÄNDIGHETER SKALL EIZO ELLER DISTRIBUTÖRERNA
HÅLLAS ANSVARIGA FÖR NÅGRA SOM HELST UNDERORDNADE, INDIREKTA, SPECIELLA, DÄRAV FÖLJANDE
ELLER ÖVRIGA SKADOR (INKLUSIVE, UTAN BEGRÄNSNING TILL, SKADOR FÖR FÖRLUST AV INKOMST,
AVBRUTEN AFFÄRSRÖRELSE, FÖRLUST AV AFFÄRSINFORMATION ELLER ANNAN SÄRSKILD FÖRLUST) SOM
UPPSTÅTT SOM ETT RESULTAT AV ANVÄNDNING ELLER OFÖRMÅGA ATT ANVÄNDA PRODUKTEN ELLER I
NÅGON FORM AV ANSLUTNING TILL PRODUKTERNA, VARE SIG DETTA GRUNDAS PÅ KONTRAKT, ÅTALBAR
HANDLING, FÖRSUMLIGHET, ANSVARSSKYLDIGHET ELLER ANNAT, ÄVEN OM EIZO ELLER DISTRIBUTÖRERNA
HAR INFORMERATS BETRÄFFANDE MÖJLIGHET ATT SÅDANA SKADOR FÖRELIGGER. DETTA UNDANTAG
OMFATTAR ÄVEN ALL FORM AV ANSVARSSKYLDIGHET SOM KAN UPPSTÅ GENOM EN TREDJE PARTS ANSPRÅK
GENTEMOT DEN URSPRUNGLIGE KÖPAREN. GRUNDBESTÅNDSDELEN I BESTÄMMELSEN ÄR ATT BEGRÄNSA
DET EVENTUELLA ANSVARSTAGANDET FÖR EIZO OCH DISTRIBUTÖRERNA SOM KAN UPPSTÅ GENOM DENNA
BEGRÄNSADE GARANTI OCH/ELLER FÖRSÄLJNING.
Appendix
63
ΠΕΡΙΟΡΙΣΜΕΝΗ ΕΓΓΥΗΣΗ
Η EIZO Corporation (στο εξής «EIZO») και οι διανομείς που εξουσιοδοτεί η EIZO (στο εξής «Διανομείς»)
παρέχουν εγγύηση, υποκείμενη και σύμφωνα με τους όρους της παρούσας περιορισμένης εγγύησης (στο εξής
«Εγγύηση»), στον αρχικό αγοραστή (στο εξής «Αρχικός Αγοραστής») ο οποίος αγόρασε το προϊόν που καθορίζεται στο
παρόν έγγραφο (στο εξής «Προϊόν») από την EIZO ή τους Διανομείς, η οποία εξασφαλίζει ότι η EIZO και οι Διανομείς,
σύμφωνα με τη διακριτή ευχέρειά τους, είτε θα επισκευάσουν είτε θα αντικαταστήσουν το Προϊόν χωρίς χρέωση εάν ο
Αρχικός Αγοραστής αντιληφθεί εντός της Περιόδου Εγγύησης (ορίζεται κατωτέρω) ότι το Προϊόν δυσλειτουργεί ή έχει
υποστεί βλάβη κατά τη διάρκεια κανονικής χρήσης του Προϊόντος σύμφωνα με την περιγραφή στο εγχειρίδιο χρήσης που
συνοδεύει το Προϊόν (στο εξής «Εγχειρίδιο Χρήστη»).
Η περίοδος της παρούσας Εγγύησης είναι τρία (3) έτη από την ημερομηνία αγοράς του Προϊόντος (στο εξής «Περίοδος
Εγγύησης»). Η EIZO και οι Διανομείς δεν φέρουν καμία ευθύνη ή υποχρέωση όσον αφορά το Προϊόν σε σχέση με τον
Αρχικό Αγοραστή ή οποιοδήποτε τρίτο μέρος, ούτε άλλη ευθύνη διαφορετική από αυτήν που παρέχεται στην παρούσα
Εγγύηση.
Η EIZO και οι διανομείς της θα πάψουν να διατηρούν αποθέματα εξαρτημάτων (εκτός από τα εξαρτήματα σχεδιασμού)
του προϊόντος μόλις περάσουν επτά (7) χρόνια αφότου διακοπεί η παραγωγή των εν λόγω εξαρτημάτων. Κατά την
επισκευή της οθόνης, η EIZO και οι Διανομείς θα χρησιμοποιήσουν ανταλλακτικά επισκευής που συμμορφώνονται με
τα πρότυπά μας για τη Διασφάλιση Ποιότητας. Αν δεν είναι εφικτή η επισκευή της μονάδας λόγω της κατάστασής της ή
λόγω έλλειψης αποθεμάτων κάποιου σχετικού εξαρτήματος, η EIZO και οι διανομείς της ενδέχεται να σας προσφέρουν τη
δυνατότητα αντικατάστασής της με προϊόν ισοδύναμων επιδόσεων αντί να την επισκευάσουν.
Η Εγγύηση ισχύει μόνο σε χώρες ή περιοχές όπου βρίσκονται οι Διανομείς. Η Εγγύηση δεν περιορίζει οποιαδήποτε
νόμιμα δικαιώματα του Αρχικού Αγοραστή.
Λαμβανομένης υπόψη κάθε διάταξης της παρούσας Εγγύησης, η EIZO και οι Διανομείς δεν θα έχουν καμία απολύτως
υποχρέωση σύμφωνα με την παρούσα Εγγύηση σε οποιαδήποτε από τις περιπτώσεις που διατυπώνονται κατωτέρω:
(α) Τυχόν ελάττωμα του Προϊόντος που προκαλείται από ζημιά κατά τη μεταφορά, τροποποίηση, αλλαγή, κατάχρηση,
λανθασμένη χρήση, ατύχημα, λανθασμένη εγκατάσταση, καταστροφή, εσφαλμένη συντήρηση ή/και λανθασμένη
επισκευή από τρίτο μέρος εκτός της EIZO και των Διανομέων,
(β) Τυχόν ασυμβατότητα του Προϊόντος λόγω πιθανών τεχνικών καινοτομιών ή/και κανονισμών,
(γ) Τυχόν επιδείνωση του αισθητήρα,
(δ) Τυχόν επιδείνωση της απόδοσης οθόνης που προκαλείται από τη φθορά αναλώσιμων εξαρτημάτων όπως
της οθόνης LCD ή/και του φωτός υποβάθρου, κτλ. (π.χ. αλλαγές στη φωτεινότητα, αλλαγές στην ομοιομορφία
φωτεινότητας, αλλαγές στο χρώμα, αλλαγές στην ομοιομορφία χρώματος, ελαττώματα σε pixel περιλαμβανομένων
των καμένων pixel, κτλ.),
(ε) Τυχόν ελάττωμα του Προϊόντος που προκαλείται από εξωτερικό εξοπλισμό,
(στ) Τυχόν ελάττωμα του Προϊόντος στο οποίο έχει τροποποιηθεί ή αφαιρεθεί ο γνήσιος αριθμός σειράς,
(ζ) Τυχόν φυσιολογική φθορά του προϊόντος, ιδιαίτερα αυτής των αναλώσιµων, των αξεσουάρ ή/και των
προσαρτηµάτων (π.χ. κουµπιά, περιστρεφόµενα µέρη, καλώδια, Εγχειρίδιο Χρήστη, κτλ.), και
(η) Τυχόν παραμόρφωση, αποχρωματισμό ή/και διαστρέβλωση του εξωτερικού μέρους του προϊόντος,
περιλαμβανομένης της επιφάνειας της οθόνης LCD.
Ο Αρχικός Αγοραστής για να δικαιούται υπηρεσίες επισκευής σύμφωνα με την Εγγύηση, θα πρέπει να παραδώσει το
Προϊόν, με πληρωμένα τα μεταφορικά έξοδα, στην αρχική του συσκευασία ή σε άλλη επαρκή συσκευασία με ισότιμο
βαθμό προστασίας, αναλαμβάνοντας τον κίνδυνο βλάβης ή/και απώλειας κατά τη μεταφορά, στον τοπικό Διανομέα. Ο
Αρχικός Αγοραστής όταν ζητά υπηρεσίες επισκευής σύμφωνα με την Εγγύηση, θα πρέπει να προσκομίζει την απόδειξη
αγοράς του Προϊόντος και την ημερομηνία της αγοράς.
Η Περίοδος Εγγύησης για οποιοδήποτε αντικατεστημένο ή/και επισκευασμένο προϊόν σύμφωνα με την παρούσα
Εγγύηση λήγει στο τέλος της αρχικής Περιόδου Εγγύησης.
Η EIZO Ή ΟΙ ΔΙΑΝΟΜΕΙΣ ΔΕΝ ΕΥΘΥΝΟΝΤΑΙ ΓΙΑ ΟΠΟΙΑΔΗΠΟΤΕ ΒΛΑΒΗ Ή ΑΠΩΛΕΙΑ ΔΕΔΟΜΕΝΩΝ Ή ΑΛΛΩΝ
ΠΛΗΡΟΦΟΡΙΩΝ ΠΟΥ ΑΠΟΘΗΚΕΥΟΝΤΑΙ ΣΕ ΟΠΟΙΟΔΗΠΟΤΕ ΜΕΣΟ Ή ΟΠΟΙΟΔΗΠΟΤΕ ΑΛΛΟ ΜΕΡΟΣ ΣΕ
ΟΠΟΙΟΔΗΠΟΤΕ ΠΡΟΪΟΝ ΠΟΥ ΕΠΙΣΤΡΕΦΕΤΑΙ ΣΤΗΝ EIZO Ή ΣΕ ΔΙΑΝΟΜΕΑ ΓΙΑ ΕΠΙΣΚΕΥΗ.
Η EIZO ΚΑΙ ΟΙ ΔΙΑΝΟΜΕΙΣ ΔΕΝ ΠΑΡΕΧΟΥΝ ΚΑΜΙΑ ΠΕΡΑΙΤΕΡΩ ΕΓΓΥΗΣΗ, ΡΗΤΗ Ή ΣΥΝΕΠΑΓΟΜΕΝΗ, ΟΣΟΝ
ΑΦΟΡΑ ΤΟ ΠΡΟΪΟΝ ΚΑΙ ΤΗΝ ΠΟΙΟΤΗΤΑ, ΤΗΝ ΑΠΟΔΟΣΗ, ΤΗΝ ΕΜΠΟΡΕΥΣΙΜΟΤΗΤΑ Ή ΤΗΝ ΚΑΤΑΛΛΗΛΟΤΗΤΑ
ΤΟΥ ΓΙΑ ΟΠΟΙΑΔΗΠΟΤΕ ΣΥΓΚΕΚΡΙΜΕΝΗ ΧΡΗΣΗ. ΣΕ ΚΑΜΙΑ ΠΕΡΙΠΤΩΣΗ Η EIZO Ή ΟΙ ΔΙΑΝΟΜΕΙΣ ΔΕΝ
ΘΑ ΕΥΘΥΝΟΝΤΑΙ ΓΙΑ ΚΑΜΙΑ ΑΠΟΛΥΤΩΣ ΤΥΧΑΙΑ, ΕΜΜΕΣΗ, ΕΙΔΙΚΗ, ΣΥΝΕΠΑΓΟΜΕΝΗ Ή ΑΛΛΗ ΒΛΑΒΗ
(ΠΕΡΙΛΑΜΒΑΝΟΜΕΝΩΝ, ΜΕΤΑΞΥ ΑΛΛΩΝ, ΒΛΑΒΩΝ Ή ΑΠΩΛΕΙΑΣ ΚΕΡΔΩΝ, ΔΙΑΚΟΠΗΣ ΕΠΙΧΕΙΡΗΜΑΤΙΚΩΝ
ΔΡΑΣΤΗΡΙΟΤΗΤΩΝ, ΑΠΩΛΕΙΑΣ ΕΠΙΧΕΙΡΗΜΑΤΙΚΩΝ ΠΛΗΡΟΦΟΡΙΩΝ Ή ΤΥΧΟΝ ΑΛΛΗΣ ΧΡΗΜΑΤΙΚΗΣ ΑΠΩΛΕΙΑΣ)
ΠΟΥ ΠΡΟΚΥΠΤΕΙ ΑΠΟ ΤΗ ΧΡΗΣΗ Ή ΤΗΝ ΑΝΙΚΑΝΟΤΗΤΑ ΧΡΗΣΗΣ ΤΟΥ ΠΡΟΪΟΝΤΟΣ Ή ΤΥΧΟΝ ΑΛΛΗΣ ΣΥΝΔΕΣΗΣ
ΜΕ ΤΟ ΠΡΟΪΟΝ, ΕΙΤΕ ΒΑΣΙΖΕΤΑΙ ΣΕ ΣΥΜΒΟΛΑΙΟ, ΒΛΑΒΗ, ΑΜΕΛΕΙΑ, ΑΥΣΤΗΡΗ ΕΥΘΥΝΗ Ή ΕΙΔΑΛΛΩΣ, ΑΚΟΜΗ
ΚΙ ΕΑΝ Η EIZO Ή ΟΙ ΔΙΑΝΟΜΕΙΣ ΕΝΗΜΕΡΩΘΟΥΝ ΓΙΑ ΤΗΝ ΠΙΘΑΝΟΤΗΤΑ ΤΕΤΟΙΩΝ ΖΗΜΙΩΝ. Η ΕΞΑΙΡΕΣΗ ΑΥΤΗ
ΠΕΡΙΛΑΜΒΑΝΕΙ ΕΠΙΣΗΣ ΟΠΟΙΑΔΗΠΟΤΕ ΕΥΘΥΝΗ ΕΝΔΕΧΕΤΑΙ ΝΑ ΠΡΟΚΥΨΕΙ ΑΠΟ ΑΞΙΩΣΕΙΣ ΤΡΙΤΟΥ ΜΕΡΟΥΣ
ΚΑΤΑ ΤΟΥ ΑΡΧΙΚΟΥ ΑΓΟΡΑΣΤΗ. Η ΟΥΣΙΑ ΤΟΥ ΟΡΟΥ ΑΥΤΟΥ ΕΙΝΑΙ ΝΑ ΠΕΡΙΟΡΙΣΕΙ ΤΗΝ ΠΙΘΑΝΗ ΕΥΘΥΝΗ ΤΗΣ
EIZO ΚΑΙ ΤΩΝ ΔΙΑΝΟΜΕΩΝ ΠΟΥ ΠΡΟΚΥΠΤΕΙ ΑΠΟ ΤΗΝ ΠΑΡΟΥΣΑ ΕΓΓΥΗΣΗ Ή/ΚΑΙ ΤΙΣ ΠΩΛΗΣΕΙΣ.
64
Appendix
ОГРАНИЧЕННАЯ ГАРАНТИЯ
EIZO Corporation (называемая в дальнейшем “EIZO”) и авторизированные EIZO дистрибуторы (называемые
в дальнейшем “Дистрибуторы”) гарантируют, в соответствии с условиями и пунктами этой ограниченной
гарантии (называемой в дальнейшем “Гарантия”), первичному покупателю (называемому в дальнейшем
“Первоначальный покупатель”), который приобрел у EIZO или Дистрибуторов продукт, указанный в этом
документе (называемый в дальнейшем “Продукт”), что EIZO или Дистрибуторы на свое усмотрение либо
бесплатно отремонтируют, либо бесплатно заменят Продукт, если Первоначальный покупатель признает в
пределах Гарантийного срока (определенного ниже), что Продукт неисправен или он поврежден процессе
нормального использования продукта в соответствии с описанием в инструкции по эксплуатации, прилагаемой
к Продукту (называемой в дальнейшем “Руководство пользователя”).
Гарантийный период ограничен сроком три (3) года от даты приобретения Продукта (называемый в дальнейшем
“Гарантийный период”). EIZO и Дистрибуторы не несут никакой ответственности и не берут обязательств
относительно Продукта по отношению к Первоначальному покупателю или по отношению к любым третьим
сторонам, кроме обязательств, оговоренных в этой Гарантии.
Компания EIZO и ее дистрибьюторы хранят детали изделия (за исключением деталей внешней конструкции) не более
7 (семи) лет после прекращения его выпуска. В случае ремонта монитора EIZO и Дистрибьюторы будут использовать
запчасти, которые соответствуют нашим стандартам QC (контроль качества). Если устройство невозможно
отремонтировать из-за его состояния или отсутствия нужной детали, то вместо ремонта компания EIZO и ее
дистрибьюторы могут предлагать замену неисправного устройства на устройство с аналогичными характеристиками.
Гарантия действительна только в странах или регионах, где расположены Дистрибуторы. Гарантия не
ограничивает никакие законные права Первоначального покупателя.
Несмотря на другие условия этой Гарантии EIZO и Дистрибуторы не несут никаких обязательств согласно этой
Гарантии в любом из перечисленных ниже случаев:
(а) Любые дефекты Продукта, вызванные повреждениями при перевозке, модификацией, изменением, неправильным
обращением, неправильным использованием, авариями, неправильной установкой, стихийными бедствиями,
неправильным уходом и/или неправильным ремонтом третьей стороной, отличной от EIZO или Дистрибуторов;
(б) Любые несовместимости Продукта из-за технических усовершенствований и/или изменения технических
норм;
(в) Любое повреждение датчика;
(г) Любые ухудшения работы дисплея, вызванные изнашиванием невосстановимых частей, таких как
панель ЖКД и/или подсветка и т.д. (например, изменение в яркости, изменение в равномерности яркости,
изменение в цветности, изменение в равномерности цветности, изменение в пикселах, включая выгоревшие
пикселы и т.д.);
(д) Любые дефекты Продукта, вызванные внешним оборудованием;
(е) Любые дефекты Продукта, при которых оригинальный серийный номер был изменен или удален;
(ж) Любые естественные ухудшения продукта, в частности, вызванные износом расходных частей,
принадлежностей и/или приспособлений (например, кнопок, вращающихся частей, кабелей, Руководства
пользователя и т.д.); и
(з) Любые деформации, изменения цвета и/или коробления внешней поверхности продукта, включая
поверхность панели ЖКД.
Чтобы получить техническое обслуживание в рамках Гарантии, Первоначальный покупатель должен доставить
Продукт местному Дистрибутору, оплатив перевозку, в его оригинальной упаковке или в другой соответствующей
упаковке, обеспечивающей равноценную степень защиты, принимая во внимание риск повреждения и/или утерю
при транспортировке. При запросе технического обслуживания в рамках Гарантии Первоначальный покупатель
должен предоставить свидетельство покупки продукта и даты покупки.
Гарантийный период для любого замененного и/или отремонтированного продукта в рамках Гарантии истекает в
конце завершения срока действия оригинального Гарантийного периода.
EIZO ИЛИ ДИСТРИБУТОРЫ НЕ НЕСУТ ОТВЕТСТВЕННОСТИ ЗА ЛЮБЫЕ ПОВРЕЖДЕНИЯ ИЛИ УТЕРЮ
ДАННЫХ ИЛИ ДРУГОЙ ИНФОРМАЦИИ, ХРАНЯЩИХСЯ НА КАКИХ-ЛИБО НОСИТЕЛЯХ ИНФОРМАЦИИ ИЛИ НА
ЛЮБЫХ ДРУГИХ ЧАСТЯХ ПРОДУКТА, КОТОРЫЙ ВОЗВРАЩЕН EIZO ИЛИ ДИСТРИБУТОРАМ ДЛЯ РЕМОНТА.
E I Z O И Д И СТ Р И БУ ТО Р Ы Н Е Д А ЮТ Н И К А К О Й Д А Л Ь Н Е Й Ш Е Й ГА РА Н Т И И , В Ы РА Ж Е Н Н О Й И Л И
ПОДРАЗУМЕВАЕМОЙ, ОТНОСИТЕЛЬНО ПРОДУКТА И ЕГО КАЧЕСТВА, ТЕХНИЧЕСКИХ ХАРАКТЕРИСТИК,
ТОВАРНОСТИ ИЛИ СООТВЕТСТВИЯ ДЛЯ КАКОГО-ЛИБО ОПРЕДЕЛЕННОГО ИСПОЛЬЗОВАНИЯ. НИ ПРИ
КАКИХ УСЛОВИЯХ EIZO ИЛИ ДИСТРИБУТОРЫ НЕ НЕСУТ ОТВЕТСТВЕННОСТИ ЗА ЛЮБОЙ СЛУЧАЙНЫЙ,
КОСВЕННЫЙ, СПЕЦИАЛЬНЫЙ, ПОБОЧНЫЙ ИЛИ ИНОЙ УЩЕРБ (ВКЛЮЧАЯ, БЕЗ ОГРАНИЧЕНИЙ, УЩЕРБ ИЗЗА НЕПОЛУЧЕННОЙ ПРИБЫЛИ, ПРЕРЫВАНИЯ БИЗНЕСА, ПОТЕРИ КОММЕРЧЕСКОЙ ИНФОРМАЦИИ ИЛИ
ЛЮБЫЕ ДРУГИЕ ФИНАНСОВЫЕ ПОТЕРИ), ВОЗНИКШИЙ ИЗ-ЗА ИСПОЛЬЗОВАНИЯ ИЛИ НЕВОЗМОЖНОСТИ
ИСПОЛЬЗОВАТЬ ПРОДУКТ ИЛИ В ЛЮБОЙ ДРУГОЙ СВЯЗИ С ПРОДУКТОМ, ЛИБО ОСНОВАННЫЙ НА
КОНТРАКТНЫХ ОТНОШЕНИЯХ, ГРАЖДАНСКИХ ПРАВОНАРУШЕНИЯХ, НЕБРЕЖНОСТИ, ПРИЧИНЕНИЯ
УЩЕРБА ТРЕТЬЕЙ СТОРОНЕ ИЛИ ЧЕМ-ЛИБО ЕЩЕ, ДАЖЕ ЕСЛИ EIZO ИЛИ ДИСТРИБУТОРЫ БЫЛИ
УВЕДОМЛЕНЫ О ВОЗМОЖНОСТИ ТАКОГО УЩЕРБА. ЭТО ИСКЛЮЧЕНИЕ ТАКЖЕ ВКЛЮЧАЕТ ЛЮБЫЕ
ОБЯЗАТЕЛЬСТВА, КОТОРЫЕ МОГУТ ВОЗНИКНУТЬ В РЕЗУЛЬТАТЕ ТРЕБОВАНИЙ ТРЕТЬЕЙ СТОРОНЫ
В ОТНОШЕНИИ ПЕРВОНАЧАЛЬНОГО ПОКУПАТЕЛЯ. СУЩЕСТВОМ ЭТОГО ПОЛОЖЕНИЯ ЯВЛЯЕТСЯ
ОГРАНИЧЕНИЕ ПОТЕНЦИАЛЬНОЙ ОТВЕТСТВЕННОСТИ EIZO И ДИСТРИБУТОРОВ, ВОЗНИКАЮЩЕЙ ИЗ-ЗА
ЭТОЙ ОГРАНИЧЕННОЙ ГАРАНТИИ И/ИЛИ ПРОДАЖ.
Appendix
65
有限责任保证书
EIZO Corporation(以下简称 “EIZO”)和 EIZO 授权的经销商(以下简称 “ 经销商 ”),接受并依照本有限责任保证书(以
下简称 “ 保证书 ”)之条款,向从 EIZO 和经销商购买本文中所规定产品(以下简称 “ 产品 ”)的原买方(以下称 “ 原买方 ”)
提供保证 :在保证期内(规定如下),如果原买方发现按本产品所附使用说明书(以下简称 “ 用户手册 ”)所述方式正常使
用本产品过程中,本产品出现故障或损坏,EIZO 和经销商根据其独自的判断免费修理或更换该产品。
本保证期限定为本产品自购买本产品之日起的三(3)年(以下简称 “ 保证期限 ”)。EIZO 和经销商将不向原买方或任何第
三方承担本保证书所规定之外的与本产品有关任何责任或义务。
零件停产七(7)年后,EIZO 及其经销商不再保留或保存产品的任何零件(设计零件除外)。维修显示器时,EIZO 与经销
商将使用符合我方质量控制标准的替换零件。若由于自身条件或缺少相关零件而不能修理设备,EIZO 和经销商可提供性能
相同的更换产品,而无需维修。
本保证书仅对于设有经销商的国家或地区有效。本保证书并不限定原买方的任何法律权利。
无论本保证书的任何其他条款如何规定,对于任何下列情况之一,EIZO 和经销商将不承担本保证书规定责任 :
(a) 由于运输损害、改装、改动、滥用、误用、意外事故、错误安装、灾害、维护不善和 / 或由除 EIZO 和经销商以外的
第三方进行不适当的修理造成本产品的任何故障。
(b) 由于可能发生的技术变更和 / 或调整造成本产品的任何不兼容性。
(c) 传感器的任何劣化。
(d) 由于诸如液晶显示屏(LCD)和 / 或背灯等消耗品部件的老化造成的任何显示性能低劣(如亮度变化、亮度均一性变化、
色彩变化、色彩均一性变化、如烧伤像素等像素缺陷)。
(e) 因外部设备造成本产品的任何故障。
(f) 因本产品的原序号被改变或消除造成本产品的任何故障。
(g) 本产品的任何正常老化,尤其是消耗品、附件和 / 或附加装置(如按钮、旋转部件、电缆、用户手册等)、以及
(h) 本产品表面包括液晶显示屏(LCD)表面的任何变形、变色和 / 翘曲。
为了获得本保证书规定的服务,原买方必须使用原包装或其他具有同等保护程度的适当包装将本产品运送到当地的经销商,
并且预付运费,承担运输中的损坏和 / 或损失的风险。要求提供本保证书规定的服务时,原买方必须提交购买本产品和标
明此购买日期的证明。
按本保证书规定进行了更换和 / 或修理的任何产品的保证期限,将在原保证期限结束时终止。
在返回给 EIZO 和经销商进行修理后,任何产品的任何媒体或任何部件中储存的数据或其他信息发生任何损坏或损失,对
此 EIZO 和经销商将不承担责任。
对于本产品及其质量、性能、可销售性以及对于特殊用途的适合性,EIZO 和经销商不提供其他任何明示或暗示的保证。因
使用本产品或无法使用本产品或因与本产品有任何关系(无论是否根据合同)而造成 : 任何附带的、间接的、特殊的、随
之发生的或其他的损害(包括但不仅限于:利润损失、业务中断、业务信息丢失或其他任何金钱损失)以及侵权行为、过失、
严格赔偿责任或其他责任,即使已经向 EIZO 和经销商提出了发生这些损害的可能性,对此 EIZO 和经销商概不承担责任。
本免责条款还包括因第三方向原买方提出索赔而可能发生的任何责任。 本条款的本质是限定由于本有限责任保证书和 / 或
销售本产品所发生的 EIZO 和经销商的潜在责任。
66
Appendix
Recycling Information
Recycling Information
This product, when disposed of, is supposed to be collected and recycled according to your country’s
legislation to reduce environmental burden. When you dispose of this product, please contact a distributor or
an affiliate in your country.
The contact addressees are listed on the EIZO website below.
http://www.eizoglobal.com
For recycling information for customers in Switzerland, please refer to the following website.
http://www.swico.ch
Informationen zum Thema Recycling
Dieses Produkt muss gemäß den Vorschriften Ihres Landes zur Entlastung der Umwelt recyclet werden.
Wenden Sie sich bei der Entsorgung dieses Produkts an einen Verteiler oder eine Tochtergesellschaft in
Ihrem Land.
Die Adressen zur Kontaktaufnahme sind auf der unten angegebenen Website von EIZO aufgeführt.
http://www.eizoglobal.com
Kunden in der Schweiz entnehmen Informationen zum Recycling der folgenden Website:
http://www.swico.ch
Informations sur le recyclage
Ce produit doit être jeté aux points de collecte prévus à cet effet et recyclé conformément à la législation de
votre pays, afin de réduire l’impact sur l’environnement. Lorsque vous jetez ce produit, veuillez contacter un
distributeur ou une société affiliée de votre pays.
Les adresses des distributeurs sont répertoriées sur le site Web EIZO ci-dessous.
http://www.eizoglobal.com
Pour les clients en Suisse, veuillez consulter le site Web suivant afin d’obtenir des informations sur le
recyclage.
http://www.swico.ch
Información sobre reciclaje
Este producto debe desecharse y reciclarse según la legislación del país para reducir el impacto
medioambiental. Cuando desee deshacerse de este producto, póngase en contacto con un distribuidor o
una filial de su país.
Encontrará las direcciones de contacto en el sitio web de EIZO que se indica a continuación.
http://www.eizoglobal.com
Informazioni sul riciclaggio
Per lo smaltimento e il riciclaggio del presente prodotto, attenersi alle normative vigenti nel proprio paese per
ridurre l’impatto ambientale. Per lo smaltimento, rivolgersi ad un distributore o un affiliato presenti nel proprio
paese.
Gli indirizzi sono elencati nel sito Web EIZO riportato di seguito.
http://www.eizoglobal.com
Per informazioni sul riciclaggio per i clienti in Svizzera, consultare il sito Web riportato di seguito.
http://www.swico.ch
Återvinningsinformation
När denna produkt kasseras ska den hanteras och återvinnas enligt landets föreskrifter för att reducera
miljöpåverkan. När du kasserar produkten ska du kontakta en distributör eller representant i ditt land.
Kontaktadresserna listas på EIZO-webbplatsen nedan.
http://www.eizoglobal.com
Appendix
67
Πληροφορίες ανακύκλωσης
Το προϊόν αυτό, όταν απορρίπτεται, πρέπει να συλλέγεται και να ανακυκλώνεται σύμφωνα με τη νομοθεσία
της χώρας σας έτσι ώστε να μην επιβαρύνει το περιβάλλον. Για να απορρίψετε το προϊόν, επικοινωνήστε με
έναν αντιπρόσωπο ή μια θυγατρική εταιρεία στη χώρα σας.
Οι διευθύνσεις επικοινωνίας αναγράφονται στην τοποθεσία web της EIZO παρακάτω.
http://www.eizoglobal.com
Сведения по утилизации
По истечении срока службы данного продукта его следует принести на сборный пункт и
утилизировать в соответствии с действующими предписаниями в вашей стране, чтобы уменьшить
вредное воздействие на окружающую среду. Прежде чем выбросить данный продукт, обратитесь к
дистрибьютору или в местное представительство компании в вашей стране.
Контактные адреса можно найти на веб-узле EIZO.
http://www.eizoglobal.com
Informatie over recycling
Wanneer u dit product wilt weggooien, moet het uit milieu-overwegingen worden verzameld en gerecycled
volgens de betreffende wetgeving van uw land. Wanneer u dit product wilt weggooien, moet u contact
opnemen met een distributeur of een partner in uw land.
De contactadressen worden vermeld op de volgende EIZO-website.
http://www.eizoglobal.com
Informação sobre reciclagem
Este produto, quando o deitar fora, deve ser recolhido e reciclado de acordo com a legislação do seu país
para reduzir a poluição. Quando deitar fora este produto, contacte um distribuidor ou uma filial no seu país.
Os endereços de contacto estão listados no website do EIZO, abaixo.
http://www.eizoglobal.com
Oplysninger om genbrug
Dette produkt forventes ved bortskaffelse at blive indsamlet og genbrugt i overensstemmelse med
lovgivningen i dit land for at reducere belastningen af miljøet. Når du bortskaffer denne produkt, skal du
kontakte en distributør eller et tilknyttet selskab i dit land.
Adresserne på kontaktpersonerne er angivet på EIZO’s websted nedenfor.
http://www.eizoglobal.com
Kierrätystä koskevia tietoja
Tuote tulee hävittää kierrättämällä maan lainsäädännön mukaisesti ympäristön kuormittumisen
vähentämiseksi. Kun hävität tuotteen, ota yhteyttä jälleenmyyjään tai tytäryhtiöön maassasi.
Yhteystiedot löytyvät EIZOn Internet-sivustolta.
http://www.eizoglobal.com
Wykorzystanie surowców wtórnych
Ten produkt po zużyciu powinien być zbierany i przetwarzany zgodnie z krajowymi przepisami dotyczącymi
ochrony środowiska. Wyrzucając ten produkt, należy skontaktować się z lokalnym dystrybutorem lub
partnerem. Adresy kontaktowe można znaleźć we wskazanej poniżej witrynie internetowej firmy EIZO.
http://www.eizoglobal.com
68
Appendix
Informace o recyklaci
Při likvidaci produktu musí být produkt vyzvednut a recyklován podle zákonů příslušné země, aby
nedocházelo k zatěžování životního prostředí. Zbavujete-li se produktu, kontaktujte distributora nebo
pobočku ve své zemi. Kontaktní adresy jsou uvedeny na následující webové stránce společnosti EIZO.
http://www.eizoglobal.com
Ringlussevõtu alane teave
Keskkonnakoormuse vähendamiseks tuleks kasutatud tooted kokku koguda ja võtta ringlusse vastavalt teie
riigi seadustele. Kui kõrvaldate käesoleva toote, võtke palun ühendust turustaja või filiaaliga oma riigis.
Kontaktisikud on toodud EIZO veebilehel järgmisel aadressil:
http://www.eizoglobal.com
Újrahasznosítási információ
Jelen terméket, amikor eldobjuk, az illető ország törvényei alapján kell összegyűjteni és újrahasznosítani,
hogy csökkentsük a környezet terhelését. Amikor ezt a terméket eldobja, kérjük lépjen kapcsolatba egy
országon belüli forgalmazóval vagy társvállalkozással.
A kapcsolat címei az EIZO alábbi weboldalán találhatók felsorolva:
http://www.eizoglobal.com
Podatki o recikliranju
Ob koncu uporabe odslužen izdelek izročite na zbirno mesto za recikliranje v skladu z okoljevarstveno
zakonodajo vaše države. Prosimo, da se pri odstranjevanju izdelka obrnete na lokalnega distributerja ali
podružnico.
Kontaktni naslovi so objavljeni na spodaj navedenih spletnih straneh EIZO:
http://www.eizoglobal.com
Informácie o recyklácii
Pri likvidácii musí byť tento výrobok recyklovaný v súlade s legislatívou vašej krajiny, aby sa znížilo zaťaženie
životného prostredia. Keď sa chcete zbaviť tohto výrobku, kontaktujte prosím distribútora alebo pobočku vo
vašej krajine.
Zoznam kontaktných adries je uvedený na nasledovnej webovej stránke firmy EIZO:
http://www.eizoglobal.com
Pārstrādes informācija
Utilizējot šo produktu, tā savākšana un pārstrāde veicama atbilstoši jūsu valsts likumdošanas prasībām
attiecībā uz slodzes uz vidi samazināšanu. Lai veiktu šī produkta utilizāciju, sazinieties ar izplatītāju vai
pārstāvniecību jūsu valstī.
Kontaktadreses ir norādītas zemāk minētajā EIZO tīmekļa vietnē.
http://www.eizoglobal.com
Informacija apie grąžinamąjį perdirbimą
Šalinant (išmetant) šiuos gaminius juos reikia surinkti ir perdirbti grąžinamuoju būdu pagal jūsų šalies teisės
aktus, siekiant sumažinti aplinkos teršimą. Kai reikia išmesti šį gaminį, kreipkitės į jūsų šalyje veikiančią
gaminių pardavimo atstovybę arba jos filialą.
Kontaktiniai adresatai nurodyti EIZO interneto svetainėje.
http://www.eizoglobal.com
Appendix
69
Информация относно рециклиране
При изхвърлянето на този продукт се предлага събирането и рециклирането му съобразно законите на
вашата страна за да се намали замърсяването на околната среда. Когато искате да се освободите от
този продукт, моля свържете се с търговския му представител или със съответните органи отговарящи
за това във вашата страна.
Данните за връзка с нас са описани на следния Интернет сайт на EIZO:
http://www.eizoglobal.com
Informaţie referitoare la reciclare
Acest produs, când debarasat, trebuie colectat şi reciclat conform legislaţiei ţării rspective ca să reducem
sarcina mediului. Când se debarasează de acest produs, vă rugăm să contactaţi un distribuitor sau un afiliat
al ţării respective.
Adresele de contact le găsiţi pe pagina de web al EIZO:
http://www.eizoglobal.com
http://www.eizoglobal.com
Geri Dönüşüm Bilgisi
Bu ürünün, atılacağı zaman, ülkenizin çevre kirliliğinin azaltılması konusundaki mevzuatına göre toplanması
ve yeniden değerlendirilmesi gerekmektedir. Ürünü atacağınız zaman lütfen ülkenizdeki bir distribütör veya
ilgili kuruluşla temasa geçiniz.
İrtibat adresleri aşağıdaki EIZO web sitesinde verilmiştir.
http://www.eizoglobal.com
70
Appendix
3rd Edition-December, 2016
Copyright © 2014-2016 EIZO Corporation. All rights reserved.
03V24894C1
(U.M-T1781)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising