Eizo | CS2410 | User manual | Eizo CS2410 User Manual

Eizo CS2410 User Manual
User’s Manual
Color Management LCD Monitor
Important
Please read this “User’s Manual”, and “PRECAUTIONS” (separate
volume) carefully to familiarize yourself with safe and effective usage.
••Refer to the “Setup Guide” for information on the installation /
connection of the monitor.
••For the latest product information including the “User’s Manual”,
refer to our web site :
www.eizoglobal.com
Location of Caution Statement
This product has been adjusted specifically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specifications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information confidential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specifications are subject to change without notice.
2

Notice for this monitor
Aside from general purposes like creating documents, viewing multimedia content, this product is also suited
to applications such as graphics creation and digital photo processing, where accurate color reproduction is
a priority.
This product has been adjusted specifically for use in the region to which it was originally shipped. If the
product is used outside the region, it may not operate as specified in the specifications.
This product may not be covered by warranty for uses other than those described in this manual.
The specifications noted in this manual are only applicable when the following are used:
•• Power cords provided with the product
•• Signal cables specified by us
Only use optional products manufactured or specified by us with this product.
If you place this product on a lacquer-coated desk, the color may adhere to the bottom of the stand due to
the composition of the rubber. Check the desk surface before use.
It takes about 30 minutes (under our measurement conditions) for the monitor display to stabilize. Please
wait 30 minutes or more after the monitor power has been turned on, and then adjust the monitor.
Monitors should be set to a lower brightness to prevent a loss in the screen quality caused by long-term use
and to maintain stable use.
When the screen image is changed after displaying the same image for extended periods of time, an
afterimage may appear. Use the screen saver or power save function to avoid displaying the same image for
extended periods of time. Depending on the image, an afterimage may appear even if it was displayed for
a short period of time. To remove such a phenomenon, change the image or keep the power turned off for
several hours.
If the monitor displays continuously over a long period of time, dark smudges or burn-in may appear. To
maximize the life of the monitor, we recommend the monitor be turned off periodically.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer
to “Cleaning” (page 4)).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may
appear on the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994 % or higher.
The backlight of the LCD panel has a fixed lifetime. Depending on the usage pattern, such as usage for
long continuous periods, the lifespan of the backlight may run out sooner, requiring replacement. When the
screen becomes dark or begins to flicker, please contact your local EIZO representative.
Do not press on the LCD panel or edge of the frame strongly, as this may result in display malfunctions, such
as interference patterns, etc. If pressure is continuously applied to the LCD panel surface, the liquid crystal
may deteriorate or the LCD panel may be damaged. (If the pressure marks remain on the panel, leave the
monitor with a black or white screen. The symptom may disappear.)
Do not scratch or press on the LCD panel with any sharp objects, at this may result in damage to the LCD
panel. Do not attempt to brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew
condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the
monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage to the
monitor.
Notice for this monitor
3
Cleaning
The stains on the cabinet and LCD panel surface can be removed by moistening part of a soft cloth with water.
Attention
•• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet
or LCD panel, and also quality deterioration of the image.
•• Never use thinner, benzine, wax, or abrasive cleaner as they may damage the cabinet or LCD panel surface.
Note
•• It is recommended that ScreenCleaner (available as an option) be used to clean the cabinet and LCD panel surface.
To use the monitor comfortably
•• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor
according to the environmental conditions.
•• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
4
Notice for this monitor
Contents
Notice for this monitor.......................................... 3
Chapter 5
Troubleshooting............................... 27
Cleaning..................................................................... 4
5-1.
No Picture..................................................... 27
To use the monitor comfortably.............................. 4
5-2.
Imaging Problems........................................ 28
Contents.................................................................. 5
5-3.
Other Problems............................................ 29
Chapter 1
Introduction........................................ 6
Chapter 6
Reference......................................... 30
1-1.
Features.......................................................... 6
6-1.
Removing the Stand.................................... 30
1-2.
Controls and Functions................................ 7
6-2.
Attaching the Optional Arm.........................31
6-3.
Attaching/Detaching the Cable Holder..... 32
6-4.
Detaching/Attaching Stand Base............... 34
6-5.
Connecting Multiple External Devices.......37
6-6.
Making Use of the USB Hub Function....... 38
●●Front................................................................. 7
●●Rear.................................................................. 8
1-3.
Supported Resolutions................................. 9
●●When using digital signal input (DVI-D,
DisplayPort, HDMI: PC signal)......................... 9
When using digital signal (HDMI: Video
signal *2)........................................................... 9
●●
1-4.
Changing the PC Display Settings.............10
●●Windows 10.....................................................10
●●Windows 8.1 / Windows 7...............................10
●●macOS............................................................11
Chapter 2
Basic Adjustments/Settings........... 12
2-1.
Switch Operation Method............................12
2-2.
Switching Input Signals...............................13
2-3.
Switching the Display Mode (color mode)....13
2-4.
Adjusting the Brightness.............................14
●●Connection Procedure................................... 38
6-7.
Specifications.............................................. 39
●●
Accessories.................................................... 40
Appendix............................................................... 41
Trademark.................................................................41
License......................................................................41
Information for Radio Interference....................... 42
●●Display Modes.................................................13
Chapter 3
3-1.
3-2.
Advanced Adjustments/Settings.... 15
Basic Operation of the Setting Menu.........15
Setting Menu Functions...............................16
●●
●●
●●
●●
●●
Color................................................................16
Signal..............................................................19
Preferences.................................................... 22
Languages......................................................24
Information......................................................24
Chapter 4
Administrator Settings.................... 25
4-1.
Basic Operation of the "Administrator
Settings" Menu............................................. 25
4-2.
"Administrator Settings" Menu
Functions...................................................... 26
Contents
5
Chapter 1 Introduction
This chapter describes the features of the monitor and the name of each control.
1-1. Features
•• 24″ widescreen
•• Resolution: Supports 1920 x 1200
•• IPS panel with 89˚ horizontal and vertical wide viewing angles
•• Frame synchronization mode supported (23.75 Hz - 30.5 Hz, 47.5 Hz - 61.0 Hz)
•• Support for three digital signal inputs (DVI-D x 1, HDMI x 1, DisplayPort x 1)
-- DisplayPort (supports 8 bit and 10 bit)*1
-- HDMI (supports 8 bit, 10 bit, and 12 bit)*1, *2
Supports PC signals by HDMI input
*1 Audio signals not supported.
*2 10 bit and 12 bit are supported only when using HDMI-Video. The maximum screen display is 8 bits.
•• Employs stand with wide range of movement.
Allows you to adjust the monitor to the optimal position for easy operation and minimizing fatigue.
(Tilt: up 35˚/down 5˚, Swivel: 344˚, Adjustable height: 155 mm (Tilt: 0°))
•• Supports portrait format
•• Compatible with color management software "ColorNavigator 7", which enables you to calibrate
monitor characteristics and generate color profiles
•• Equipped with a USB Hub function that supports USB 3.1
Achieves high-speed data transfers of up to 5 Gbps, which enables transfers of large amounts of data to and
from USB-connected devices in a short amount of time.
Also, the "CHARGE" USB downstream port supports quick charging, so you can recharge your smartphone
or tablet in a short period of time.
See “6-6. Making Use of the USB Hub Function” (page 38) and “USB CHARGE Port” (page 23)
•• Displays HDCP (High Bandwidth Digital Protection) protected content.
Note
•• This monitor supports portrait format. When using the screen in a portrait position, you can change the
orientation of the Setting menu (see “Menu Rotation” (page 22)).
•• When using the monitor screen in a portrait position, the graphics board supporting portrait display is
required. When placing the monitor in a portrait position, settings of your graphics board need to be changed.
Refer to the User's Manual of the graphics board for details.
6
Chapter 1
Introduction
1-2. Controls and Functions
●●Front
1
2
1. Operation switches
Displays menus. Operate the switches according to the operation
guide.
Touch the switch to display its menu.
The switch indicators are lit white when you turn on the power.
2. Power switch
Turns the power on or off.
Touch the switch to turn the power on.
The switch indicator is lit when you turn the power on. The indicator
color differs depending on the monitor's operation status.
White
: Normal operating mode
Orange : Power saving mode
OFF
: Power off
Chapter 1
Introduction
7
●●Rear
3
5
4
6
7
8
9
3. Transportation handle
10
12
11
13
14
This handle is used for transportation.
Attention
•• Firmly grasp and hold the monitor by the bottom while grabbing the
handle, and carefully convey the monitor so as not to drop it.
4. Lock button
Use this button when removing the stand from the monitor.
5. USB Type-A connector
(USB downstream port)
Connects to a peripheral USB device. Supports USB 3.1. The
"CHARGE" port
supports quick recharging (page 23).
6. Security lock slot
Complies with Kensington's MicroSaver security system.
7. Stand
*1
8. Cable holder
9. Main power switch
Adjusts the height and angle (tilt and swivel) of the monitor.
Covers the monitor cables. For details on attaching the cable holder, see
“6-3. Attaching/Detaching the Cable Holder” (page 32).
Turns the main power on or off. : On,
: Off
10. Power connector
Connects the power cord.
11. DVI connector
Connects to an external device that has DVI output.
12. HDMI connector
Connects to an external device that has HDMI output.
13. DisplayPort connector
Connects to an external device that has DisplayPort output.
14. USB Type-B connector
Connects to the USB cable when using software that requires a USB
(USB upstream port)
connection, or when using the USB Hub function.
*1 An optional arm (or an optional stand) can be attached by removing the stand section (refer to “6-2.
Attaching the Optional Arm” (page 31)).
8
Chapter 1
Introduction
1-3. Supported Resolutions
The monitor supports the following resolutions.
using digital signal input (DVI-D, DisplayPort, HDMI: PC
●●When
signal)
Resolution
Dot Clock
640 x 480
720 x 400
800 x 600
1024 x 768
1280 x 960
1280 x 1024
1600 x 1200
1680 x 1050
1680 x 1050
1920 x 1080
1920 x 1200 *1
25.175 MHz
28.322 MHz
40.000 MHz
65.000 MHz
108.000 MHz
108.000 MHz
162.000 MHz
119.000 MHz
146.250 MHz
138.500 MHz
154.000 MHz
Horizontal Scan
Frequency
31.469 kHz
31.469 kHz
37.879 kHz
48.363 kHz
60.000 kHz
63.981 kHz
75.000 kHz
64.674 kHz
65.29 kHz
66.587 kHz
74.038 kHz
Vertical Scan
Frequency
59.940 Hz
70.087 Hz
60.317 Hz
60.004 Hz
60.000 Hz
60.020 Hz
60.000 Hz
59.883 Hz
59.954 Hz
59.934 Hz
59.950 Hz
*1 Recommended resolution
●●When using digital signal (HDMI: Video signal
Resolution
Dot Clock
640 x 480
720 (1440) x 480i (4:3)
720 (1440) x 480i (16:9)
720 x 480p (4:3)
720 x 480p (16:9)
720 (1440) x 576i (4:3)
720 (1440) x 576i (16:9)
720 x 576p (4:3)
720 x 576p (16:9)
1280 x 720p
1280 x 720p
1920 x 1080i
1920 x 1080i
1920 x 1080p
1920 x 1080p
1920 x 1080p
1920 x 1080p
1920 x 1080p
25.200 MHz
27.027 MHz
27.027 MHz
27.027 MHz
27.027 MHz
27.000 MHz
27.000 MHz
27.000 MHz
27.000 MHz
74.250 MHz
74.250 MHz
74.250 MHz
74.250 MHz
74.250 MHz
74.250 MHz
74.250 MHz
148.500 MHz
148.500 MHz
*2
)
Horizontal Scan
Frequency
31.500 kHz
15.750 kHz
15.750 kHz
31.500 kHz
31.500 kHz
15.625 kHz
15.625 kHz
31.250 kHz
31.250 kHz
37.500 kHz
45.000 kHz
28.125 kHz
33.750 kHz
27.000 kHz
28.125 kHz
33.750 kHz
56.250 kHz
67.500 kHz
Vertical Scan
Frequency
60.000 Hz
60.000 Hz
60.000 Hz
60.000 Hz
60.000 Hz
50.000 Hz
50.000 Hz
50.000 Hz
50.000 Hz
50.000 Hz
60.000 Hz
50.000 Hz
60.000 Hz
24.000 Hz
25.000 Hz
30.000 Hz
50.000 Hz
60.000 Hz
*2 To display video signals by HDMI signal input, you must change the monitor settings beforehand. (See
“Signal Format” (page 26))
Chapter 1
Introduction
9
1-4. Changing the PC Display Settings
If the screen is not properly displayed after connecting the monitor to a PC, follow the procedure below to
change the PC display settings.
●●Windows 10
1. Right-click anywhere on the desktop except for on icons to display the menu.
2. From the displayed menu, click "Display settings" to display the "Settings" screen.
3. If there are multiple monitors including the notebook PC screen connected to the computer,
select "Extend these displays" from the "Multiple displays" menu, and click "Keep changes" in the
confirmation screen. After changing the settings, select the monitor from the "Select and arrange
display" menu.
4. By checking the option "Make this my main display" from the "Multiple displays" menu, the display
of the monitor will be corrected.
5. Confirm that the monitor's recommended resolution is set in the "Resolution" menu (the term
(Recommended) should be displayed after the resolution).
6. To change the size of letters and icons, select the preferred magnification level from the scaling (%)
menu.
7. When after changing these settings a message is displayed that prompts you to sign out, sign out
once and then sign in again.
●●Windows 8.1 / Windows 7
* For Windows 8.1, click the "Desktop" tile on the Start Screen to display the desktop.
1. Right-click anywhere on the desktop except for on icons to display the menu.
2. From the displayed menu, click "Screen resolution" to display the settings screen.
3. If there are multiple monitors including the notebook PC screen connected to the computer, select
"Extend these displays" from the "Multiple displays" menu, and click "Apply". In the confirmation
screen, click "Keep changes".
4. Select the monitor from the "Display" menu, check the option "Make this my main display", and
click "Apply". The display of the monitor will be corrected.
5. Confirm that the monitor's recommended resolution is set in the "Resolution" menu (the term
(Recommended) should be displayed after the resolution).
6. To change the size of letters and icons, click "Make text and other items larger or smaller", select
the preferred size from the settings screen, and click "Apply".
7. When after changing settings a message is displayed that prompts you to sign out or log off, sign
out or log off once and then sign in or log on again.
10
Chapter 1
Introduction
●●macOS
1. Select "System Preferences" from the Apple menu.
2. When the "System Preferences" panel is displayed, click "Displays".
3. If there are multiple monitors including the notebook PC screen connected to the computer, open
the "Arrangement" tab and confirm that "Mirror displays" is not selected. If it is selected, clear it.
4. Select the "Display" tab, and confirm that "Default for display" of "Resolution" is selected. If it is not
selected, select it. This sets the correct resolution. Close the "System Preferences" menu. If there
are multiple monitors including the notebook PC screen connected to the computer, change the
settings for each monitor by using "Display".
5. To select a different resolution, select "Scaled", select a resolution from the resolution list (displayed
in list or icon format), and close the panel.
Chapter 1
Introduction
11
Chapter 2 Basic Adjustments/Settings
This chapter describes the basic functions that can be set by touching the switches on the front of the
monitor.
For advanced adjustment and setting procedures using the Setting menu, see “Chapter 3 Advanced
Adjustments/Settings” (page 15).
2-1. Switch Operation Method
1. Displaying the operation guide
1. Touch any switch (except
).
The operation guide appears on the screen.
2. Setting
1. Touch a switch for setting.
The Setting menu appears.
2. Use the switches to adjust/set the selected item, and then select
3. Exiting
1. Select
or
to exit the menu.
Note
•• The contents of the guide will differ depending on the selected menu or status.
12
Chapter 2
Basic Adjustments/Settings
to confirm.
2-2. Switching Input Signals
When a monitor has multiple signal inputs, the signal to display on-screen can be changed.
Touch any switch and select
to switch to the input terminal of the input you want to display.
2-3. Switching the Display Mode (color mode)
This function allows easy selection of a display mode according to monitor application.
Touch any switch and select
to switch to the color mode you want to use.
●●Display Modes
Color Mode
Standard Mode
Purpose
Adjust color using the monitor's Setting menu.
You can also adjust the monitor’s display using color management
software "ColorNavigator 7".
Custom
Select for configuring color settings according to your preference.
sRGB
Suitable for color matching with sRGB compatible peripherals.
Advanced Mode
Adjusts the monitor’s display using the "ColorNavigator 7" color
management software.
CAL1
CAL2
CAL3
Displays the screen adjusted by ColorNavigator 7.
Note
•• Use ColorNavigator 7 to set Advanced Mode (CAL1 to CAL3). These settings cannot be changed in the
Setting menu on the monitor.
•• You can set the color mode for each input signal.
•• You can disable specific color mode selections. For more information, see “Mode Skip” (page 24).
Chapter 2
Basic Adjustments/Settings
13
2-4. Adjusting the Brightness
The brightness of the screen can be adjusted to suit the installation environment or personal preference.
Settings
0% to 100%
14
Chapter 2
Basic Adjustments/Settings
Chapter 3 Advanced Adjustments/Settings
This chapter describes the advanced monitor adjustment and setting procedures using the Setting menu.
For the basic setting functions using the switches on the front of the monitor, see “Chapter 2 Basic
Adjustments/Settings” (page 12).
3-1. Basic Operation of the Setting Menu
1. Menu display
1. Touch any switch (except
).
The operation guide appears.
2. Select
.
The Setting menu appears.
2. Adjusting/setting
1. Choose a menu to adjust/set with
, and then select
.
The Sub menu appears.
Chapter 3
Advanced Adjustments/Settings
15
2. Choose an item to adjust/set with
, and then press
.
, and then select
.
The Adjustment/Setting menu appears.
3. Adjust/set the selected item with
The Sub menu appears.
Selecting
during adjustment/setting will cancel the adjustment/setting and restore the state prior to
making changes.
3. Exiting
1. Select
.
The Setting menu appears.
2. Select
.
The Setting menu exits.
Note
•• The contents of the guide will differ depending on the selected menu or status.
3-2. Setting Menu Functions
●●Color
When the screen is displayed in Standard Mode (Custom / sRGB), you can adjust the color settings
of each color mode according to your preference.
Attention
•• The same image may be seen in different colors on multiple monitors due to differences between individual
monitors. Make fine color adjustment visually when matching colors on multiple monitors.
Note
•• Use the values shown in "K" and "%" as a guide only.
Function
Color Mode
16
Chapter 3
Settings
Custom
sRGB
CAL1
CAL2
CAL3
Advanced Adjustments/Settings
Description
Switch to the desired mode according to the monitor
application.
Note
•• For more information on how to switch modes, see “2-3.
Switching the Display Mode (color mode)” (page 13).
Function
Settings
Description
Brightness
0% to 100%
The screen brightness is adjusted by changing the brightness
of the backlight (light source from the LCD back panel).
Temperature
Native
4000 K to 10000 K
sRGB
User
The color temperature can be adjusted.
The color temperature is used to express the chromaticity of
"White". The value is expressed in degrees "K" (Kelvin).
The screen becomes reddish at a low color temperature, and
bluish at a high color temperature, like the temperature of a
flame.
Specify a color temperature in units of 100 K, or select a
standard name.
Note
•• When you select "Native", the original color of the LCD panel
(Gain: 100 % for each RGB) is displayed.
•• "Gain" allows you to perform more advanced adjustment.
When gain is changed, the color temperature is changed to
"User".
•• The gain preset values are set for each color temperature
setting value.
Gamma
1.6 to 2.7
sRGB
Adjust the gamma.
The brightness of the monitor varies depending on the input
signal, however, the variation rate is not simply proportional
to the input signal. The control performed to keep the balance
between the input signal and the brightness of the monitor is
called "Gamma correction".
Set the gamma, or select a standard name.
Color Gamut
Native
sRGB
Set the color reproduction area (color gamut).
"Color Gamut" is the range of colors that can be represented.
Multiple standards are defined.
Note
•• Select "Native", to display the original color gamut of the
monitor.
•• The method of displaying colors outside the monitor's
displayable range within the defined color gamut can be set.
For more information, see “Clipping” (page 18).
Chapter 3
Advanced Adjustments/Settings
17
Function
Advanced Hue
Settings
Settings
-100 to 100
Description
Adjust the hue.
Note
•• Using this function may make some color gradations unavailable for
display.
Saturation
-100 to 100
Adjust the color saturation.
Note
•• Using this function may make some color gradations unavailable for
display.
•• The minimum value (-100) changes the screen to monochrome.
Clipping
On
Off
The method of displaying colors outside the monitor's displayable
range within the color gamut specified in accordance with “Color
Gamut” (page 17) can be set.
•• "On"
The range of colors that are
displayable on the monitor will be
accurately displayed in accordance
with the standard. Colors outside
the displayable range will be
saturated.
•• "Off"
Displays colors with priority on
the color gradation rather than
the color accuracy. The vertices
of the color gamut defined in the
standard move to a range that
can be displayed by the monitor.
This allows the closest colors
displayable by the monitor to be
displayed.
Color gamut displayable by
the monitor
Color gamut defined by
standard
Color gamut displayed on
screen
Note
•• The diagrams shown above are conceptual diagrams, and they do not
display the actual color gamut of the monitor.
•• This setting will be disabled if "Native" is selected at “Color Gamut”
(page 17).
Gain
0 % to 100 % The brightness of each color component red, green, and blue is called
Gain. The hue of "white" can be changed by adjusting the gain.
Note
•• Using this function may make some color gradations unavailable for
display.
•• The gain value changes according to the color temperature.
•• When gain is changed, the color temperature is changed to "User".
6 Colors
Reset
18
Chapter 3
-100 to 100
The hue, saturation, and lightness can each be adjusted for the colors
Magenta, Red, Yellow, Green, Cyan, and Blue.
OK
Cancel
Resets any color adjustment values for the currently selected color mode
back to the default settings.
Advanced Adjustments/Settings
●●Signal
The signal settings are used to configure advanced settings for input signals, such as the screen
display size and color format.
Chapter 3
Advanced Adjustments/Settings
19
Function
Picture Expansion
Settings
*1
Auto
Full Screen
Aspect Ratio
Dot by Dot
Description
The screen size of the monitor display can be changed.
•• "Auto"
The monitor automatically changes the screen size
according to the resolution information and aspect ratio
information from the input signal.
•• "Full Screen"
Displays an image in full screen. Images are distorted
in some cases because the magnification ratio is not
necessarily fixed vertically and horizontally.
When using video signal (480p/i, 576p/i) input, the image
will be displayed in full screen while maintaining the 16:9
aspect ratio.
•• "Aspect Ratio"
Displays an image in full screen. However, since aspect
ratios are maintained, part of an image may not be visible in
horizontal or vertical direction.
When using video signal (480p/i, 576p/i) input, the image
will be displayed in full screen while maintaining the 4:3
aspect ratio.
•• "Dot by Dot"
Displays the image at the set resolution or at the size
specified by the input signal.
Note
•• Example settings
--Full Screen
--Aspect Ratio
--Dot by Dot (Input Signal)
*1 Only enabled when input signal information for automatically determining the setting is detected during
HDMI input
20
Chapter 3
Advanced Adjustments/Settings
Function
Input Color Format
Settings
*2
Auto
YUV 4:2:2
YUV 4:4:4
RGB
Description
The color space of the input signal can be specified.
Try changing this setting if colors are not displayed correctly.
Normally, select "Auto".
Note
•• Cannot be set for DVI input.
Input Range
Auto*3
Full
Limited (109%
white)
Limited
Depending on the external device, the black and white levels
in the video signal output to the monitor may be restricted. If
the signal is displayed on the monitor in its restricted form, the
blacks will be faint, the whites dull, and contrast will be reduced.
The brightness range of such signals can be extended to match
the actual contrast ratio of the monitor.
•• "Auto"
The monitor automatically recognizes the brightness range of
input signals and displays images appropriately.
•• "Full"
The input signal brightness range is not extended.
•• "Limited (109% white)"
The brightness range of the input signal is extended from
16 - 254 (10 bits: 64 - 1019) to 0 - 255 (10 bits: 0 - 1023) for
display.
•• "Limited"
The brightness range of the input signal is extended from
16 - 235 (10 bits: 64 - 940) to 0 - 255 (10 bits: 0 - 1023) for
display.
Noise Reduction
On
Off
The small noises that occur in dark areas of an image are
reduced. Use this function to reduce noise and roughness in
images.
Note
•• This can only be set when there is HDMI input.
•• Using the Noise Reduction function may lead to deterioration
of fine images.
*2 Only enabled when input signal information for automatically determining the setting is detected
*3 Disabled during DVI input
Chapter 3
Advanced Adjustments/Settings
21
●●Preferences
The monitor's settings can be configured to suit the usage environment or personal preference.
Function
Auto Input Detection
Settings
Off
On
Description
When this function is set to "On", the monitor automatically
recognizes the connector through which signals are input,
so that the screen can be displayed. When the input signal
of the selected connector disappears, another signal is
automatically displayed.
When set to "Off", the monitor displays the signal from the
selected connector regardless of whether a signal is input or
not. In this case, select the input signal to display using the
operation switch (
) on the front of the monitor.
Note
•• When the main power is turned on/off, the signal is
detected automatically regardless of the setting for this
function.
Menu Rotation
0°
90°
This function allows you to change the orientation of the
Setting menu to align with the installation orientation.
Note
•• When using the monitor screen in a portrait position, the
graphics board supporting portrait display is required.
When placing the monitor in a portrait position, settings
of your graphics board need to be changed. Refer to the
User's Manual of the graphics board for details.
•• When using the monitor in a portrait position, rotate the
monitor after pulling up the screen to the uppermost
position of the stand and setting the screen tilted upward.
22
Chapter 3
Advanced Adjustments/Settings
Function
USB CHARGE Port
Settings
Normal
Charging Only
Description
The "CHARGE" USB downstream port of the monitor
supports USB 3.1 quick charging. By changing this setting to
"Charging Only", devices connected to the "CHARGE" port
can be charged more quickly than when using the "Normal"
setting.
Note
•• Make sure to complete any communication between
connected USB devices and the PC before switching this
setting. When the setting is switched, all communication
will be temporarily interrupted.
•• Devices that are connected to the "CHARGE" port must
support quick charging.
•• When "Charging Only" is set, data communications
between the PC and connected devices via the "CHARGE"
port are not possible, and therefore, connected devices
will not work.
•• When "Charging Only" is set, charging is possible even
when the monitor and PC are not connected by USB
cable.
Power Save
On
Off
This function allows you to set the monitor to the power
saving mode, depending on the state of an external device
connected to it.
The monitor changes to power saving mode about 15
seconds after signal input ceases to be detected. When the
monitor has shifted to power saving mode, images are not
displayed on the screen.
•• Exiting power saving mode
--If the monitor receives input, it automatically exits
power saving mode and returns to the normal display
mode.
Note
•• At the time of shifting to power saving mode, a message
that indicates the transition is displayed 5 seconds in
advance.
•• When you are not using the monitor, turn off the main
power switch to cut down on power consumption.
•• When the monitor is in power saving mode, devices
connected to the USB downstream port will still work.
Therefore, power consumption of the monitor varies
depending on the connected devices, even in the power
saving mode.
Indicator
Off
1 to 7
The brightness of the power switch and the operation
switches when the screen is displayed can be set. (Default
setting: 4)
Beep
On
Off
You can set the beep that sounds each time a switch is
operated.
Input Skip
Skip
-
This function allows skipping of input signals that will not be
used when the input signals are switched.
Note
•• Not all input signals can be set to "Skip".
Chapter 3
Advanced Adjustments/Settings
23
Function
Mode Skip
Settings
Skip
-
Description
This function allows skipping of modes that will not be used
when selecting modes. Please use this function if display
modes are limited, or if you want to prevent randomly
changing the display status.
Note
•• Not all modes can be set to "Skip".
Monitor Reset
OK
Cancel
Restores all settings to their default values, except for the
settings in the "Administrator Settings" menu.
●●Languages
The display language for menus and messages can be selected.
Settings
English, German, French, Spanish, Italian, Swedish, Japanese, Simplified Chinese, Traditional
Chinese
●●Information
You can check the monitor information (model name, serial number (S/N), firmware version, usage
time) and the input signal information.
Example:
24
Chapter 3
Advanced Adjustments/Settings
Chapter 4 Administrator Settings
This chapter describes how to configure monitor operation using the "Administrator Settings" menu.
This menu is for administrators. Configuration on this menu is not required for normal monitor use.
4-1. Basic Operation of the "Administrator Settings"
Menu
1. Menu display
1. Touch
to turn off the monitor.
2. While touching the leftmost switch, touch
for more than 2 seconds to turn on the monitor.
The "Administrator Settings" menu appears.
2. Setting
1. Choose an item to set with
, and then select
.
The Adjustment/Setting menu appears.
2. Set the item with
, and then select
.
The "Administrator Settings" menu appears.
3. Applying and exiting
1. Select "Apply", and then select
.
The settings are confirmed and the "Administrator Settings" menu quits.
Chapter 4 Administrator Settings
25
4-2. "Administrator Settings" Menu Functions
Function
Settings
Description
On-Screen Logo
Off
On
When this function is set to "Off", the EIZO logo that is displayed
when the monitor is turned on does not appear.
Key Lock
Off
Menu
All
In order to prevent changes to settings, the operation switches on
the front of the monitor can be locked.
•• "Off" (Default setting)
Enable all switches.
•• "Menu"
Lock the
switch.
•• "All"
Lock all switches except the power switch.
DP Power Save
On
Off
When you switch the power back on or return from power save mode
while the PC is connected via the DisplayPort connector, windows or
icons may have shifted position. In such cases, set this function to
"Off".
DUE Priority
Uniformity
Brightness
This product is equipped with a Digital Uniformity Equalizer (DUE)
function that reduces display unevenness. This DUE setting can be
changed.
•• "Uniformity"
Prioritizes reduction of display unevenness.
•• "Brightness"
Prioritizes high brightness and high contrast.
Note
•• When changing the DUE setting, the monitor whose display
is adjusted must be re-calibrated. Perform the calibration
again.
Signal
Format
26
DisplayPort
RGB/YUV
RGB
HDMI
Video
PC
Chapter 4 Administrator Settings
You can switch the signal type that the monitor can display.
To display video signals when using HDMI signal input, set to
"Video".
Chapter 5 Troubleshooting
5-1. No Picture
Problem
1. No picture
•• Power indicator does not light up.
Possible cause and remedy
••
••
••
••
Check whether the power cord is connected properly.
Turn on the main power switch on the rear side of the monitor.
Touch .
Turn off the main power switch on the rear side of the monitor,
and then turn it on again a few minutes later.
•• Power indicator is lighting white.
•• Increase "Brightness" and/or "Gain" in the Setting menu (see
“Color” (page 16)).
•• Power indicator is lighting orange.
••
••
••
••
•• Power indicator is flashing orange and
white.
2. The message below appears.
•• This message appears when no signal is
input.
Example:
•• The message shows that the input signal
is out of the frequency specification range.
Example:
Switch the input signal.
Move the mouse or press any key on the keyboard.
Check whether the external device is turned on.
Turn off the main power switch on the rear side of the monitor,
and then turn it on again.
•• This problem may occur when an external device is
connected via the DisplayPort connector. Connect via the
signal cable specified by EIZO, turn off the monitor, and then
turn it on again.
This message appears when the signal is not input correctly even
though the monitor is functioning properly.
•• The message shown left may appear, because some external
devices do not output the signal immediately after power-on.
•• Check whether the external device is turned on.
•• Check whether the signal cable is connected properly.
•• Switch the input signal.
•• Turn off the main power switch on the rear side of the monitor,
and then turn it on again.
•• Try changing "Signal Format" in the "Administrator Settings"
menu (see “Signal Format” (page 26)).
•• Check whether the external device is configured to meet the
resolution and vertical scan frequency requirements of the
monitor (see “1-3. Supported Resolutions” (page 9)).
•• Reboot the external device.
•• Change to the appropriate setting using the graphics board's
utility. Refer to the User's Manual of the graphics board for
details.
Chapter 5
Troubleshooting
27
5-2. Imaging Problems
28
Problem
Possible cause and remedy
1. The screen is too bright or too dark.
•• Use "Brightness" in the Setting menu to adjust it (see “Color”
(page 16)). The LCD monitor backlight has a limited life span.
If the screen becomes dark or begins to flicker, contact your
local EIZO representative.
2. Afterimages appear
•• Afterimages are particular to LCD monitors. Avoid displaying
the same image for a long time.
•• Use the screen saver or power saving function to avoid
displaying the same image for extended periods of time.
3. Green/red/blue/white dots remain on
the screen
/ Defective dots remain on the screen
•• This is due to LCD panel characteristics and not a malfunction.
4. Interference patterns or pressure
marks remain on the screen.
•• Display a white or black image over the entire screen. The
symptom may disappear.
5. Noise appears on the screen.
•• When inputting HDCP system signals, normal images may not
be displayed immediately.
6. (For DisplayPort signal input)
When you switch the power back on
or return from power saving mode,
windows or icons may have shifted
position.
•• In the "Administrator Settings" menu, set "DP Power Save" to
"Off" (see “DP Power Save” (page 26)).
7. (For DisplayPort or HDMI signal
input)
The screen colors look strange.
•• Try changing "Input Color Format" in the Setting menu (see
“Input Color Format” (page 21)).
•• For HDMI signal input, try changing "Signal Format" in the
"Administrator Settings" menu (see “Signal Format” (page
26)).
8. The image does not display on the
entire screen.
•• Try changing "Picture Expansion" in the Setting menu (see
“Picture Expansion” (page 20)).
•• For HDMI signal input, check whether "Signal Format" is set to
"PC" in the "Administrator Settings" menu (see “Signal Format”
(page 26)).
•• Is the resolution set to the recommended resolution (1920 x
1200)? For details on the settings, refer to the User's Manual of
the graphics board.
Chapter 5
Troubleshooting
5-3. Other Problems
Problem
Possible cause and remedy
1. The Setting menu/Mode menu
cannot be displayed
•• Check whether the operation switch lock function works (see “Key
Lock” (page 26)).
•• Control switches are locked when the main window of ColorNavigator
7 is displayed. Exit the software.
2. The monitor connected with
the USB cable is not detected.
/ The peripheral USB device
connected to the monitor does
not work.
•• Check whether the USB cable is connected correctly (see “6-6.
Making Use of the USB Hub Function” (page 38)).
•• If a peripheral device is connected to the "CHARGE" port, try
checking the "USB CHARGE Port" setting (see “USB CHARGE Port”
(page 23)). If it is set to "Charging Only", the peripheral device will
not work.
•• Try changing to a different USB port on the external device.
•• Try changing to a different USB port on the monitor.
•• Reboot the external device.
•• If the peripheral devices work correctly when the external device and
peripheral devices are connected directly, contact your local EIZO
representative.
•• Check whether the external device and OS are USB compliant.
(For USB compliance of the respective devices, consult their
manufacturers.)
•• Depending on the USB 3.1 host controller that you are using,
connected USB devices may not be recognized correctly. Update to
the latest USB 3.1 driver provided by each manufacturer, or connect
the monitor to the USB 2.0 port.
•• Check the external device's BIOS setting for USB when using
Windows. (Refer to the User's Manual of the external device for
details.)
3. Audio is not output.
•• This product is not equipped with a speaker.
Chapter 5
Troubleshooting
29
Chapter 6 Reference
6-1. Removing the Stand
The stand section of this product can be removed.
Attention
•• Do not move the removed stand up and down. Doing so may result in injury or equipment damage.
•• Since the monitor and stand are heavy, dropping them may result in injury or equipment damage.
1. To prevent damaging the panel surface, lay the monitor with its panel surface
facing down on a soft cloth spread on a stable surface.
2. Remove the stand.
Press and hold he lock button (1), firmly grip the stand support, and then slide the stand in the
direction of the base of the stand (2).
When the tab that holds the stand in place loosens, remove the stand (3).
(3)
(2)
(1)
30
Chapter 6
Reference
6-2. Attaching the Optional Arm
An optional arm (or an optional stand) can be attached by removing the stand section. Please refer to our
web site for the corresponding optional arm (or optional stand). www.eizoglobal.com
Attention
•• When attaching an arm or stand, follow the instructions of their User's Manual.
•• When using another manufacturer's arm or stand, confirm the following in advance and select one conforming
to the VESA standard. Use the VESA mounting screws supplied with this product when attaching the arm or
stand.
-- Clearance between screw holes: 100 mm x 100 mm
-- External dimensions of the VESA mount section of the arm or stand: 122 mm x 122 mm or less
-- Plate thickness: 2.6 mm
-- Must be strong enough to support weight of the monitor unit (excluding the stand) and attachments such as
cables.
•• When using an arm or stand, attach it to meet the following tilt angles of the monitor.
-- Up 45˚, down 45˚
•• Connect the cables after attaching an arm or stand.
•• Since the monitor and arm or stand are heavy, dropping them may result in injury or equipment damage.
•• When installing the monitor in portrait mode, turn the monitor screen 90˚ in clockwise direction.
Attaching the Optional Arm (or Optional Stand)
1. Attach the arm or stand to the monitor.
Use the VESA mounting screws supplied with this product when attaching the arm or stand.
Attaching the Original Stand
1. To prevent damaging the panel surface, lay the monitor with its panel surface
facing down on a soft cloth spread on a stable surface.
2. Remove the fixing screws on the optional arm (or optional stand), and detach
the optional arm (or optional stand).
3. Attach the original stand.
Insert the four tabs on the stand into the square holes on the back panel (1) and slide the stand
towards the upper portion of the monitor until it makes a clicking sound (2).
(1)
(2)
Chapter 6
Reference
31
6-3. Attaching/Detaching the Cable Holder
A cable holder is supplied with this product. Use the cable holder to organize the cables connected to the
monitor.
Attachment procedure
1. Pass the cables through the cable holder.
2. Close the cable holder.
3. In this state, insert the cable holder into the stand.
Note
•• The cable holder can be inserted either perpendicular or parallel to the stand. Change the orientation of the cable
holder in line with the direction of the cables.
32
Chapter 6
Reference
Detachment procedure
1. Close the cable holder.
2. In this state, pull the cable holder from the stand.
Chapter 6
Reference
33
6-4. Detaching/Attaching Stand Base
Detachment procedure
The stand base that was attached during setup can be detached using the following procedures.
1. To prevent damaging the panel surface, lay the monitor on a soft cloth spread
on a stable surface with the panel surface facing down.
2. Raise the lever on the bottom of the stand base.
3. Turn the stand base in the counterclockwise direction to detach it.
34
Chapter 6
Reference
Attachment procedure
The detached stand base can be attached to the monitor again with the following procedures.
1. To prevent damaging the panel surface, lay the monitor on a soft cloth spread
on a stable surface with the panel surface facing down.
2. Attach the stand base onto the stand brace.
Chapter 6
Reference
35
3. Turn the stand base clockwise until it makes a clicking sound.
Cl i c
36
Chapter 6
Reference
k!
6-5. Connecting Multiple External Devices
The product allows you to connect multiple external devices and switch between them for display.
Connection examples
DVI
HDMI
DisplayPort
DD200-BK(DVI-D - DVI-D)
HH200HS(HDMI - HDMI)
PP200 (DisplayPort - DisplayPort)
DVI
HDMI
DisplayPort
Note
•• The input signal changes each time the operation switch (
) on the front of the monitor is touched. For
more information, see "2-2. Switching Input Signals" (page 13).
•• The connector through which signals are input is recognized automatically, and images are displayed on the
screen accordingly. For more information, see "Auto Input Detection" (page 22).
•• If the connector for your external device is a Thunderbolt 3/USB Type-C connector, use a USB Type-C DisplayPort converter cable.
Chapter 6
Reference
37
6-6. Making Use of the USB Hub Function
This monitor is equipped with a USB hub. It works as a USB hub when connected to a USB-compatible
external device, allowing the connection of peripheral USB devices.
●●Connection Procedure
1. Connect the USB cable between the USB downstream port of the external device and the USB
upstream port of the monitor.
USB cable (UU200SS)
For the locations of the monitor's USB upstream port, see "Rear" (page 8).
2. Connect the peripheral USB device to the USB downstream port of the monitor.
Attention
•• This monitor may not work depending on the used external device, OS or peripheral devices. For USB
compatibility of peripheral devices, contact their manufactures.
•• When the monitor is in power saving mode, devices connected to the USB downstream port will still work.
Therefore, power consumption of the monitor varies depending on the connected devices, even in the power
saving mode.
•• When the main power switch of the monitor is off, a device connected to the USB downstream port will not
operate.
•• When the "USB CHARGE Port" setting in "Preferences" is set to "Charging Only", a peripheral device will not
work if connected to the "CHARGE" port (see "USB CHARGE Port" (page 23)).
•• Ensure that communication between all peripheral devices connected to the monitor and the external device is
ended before switching the "USB CHARGE Port" setting. When the setting is switched, all communication will be
temporarily interrupted.
Note
•• This product supports USB 3.1 Gen 1. When connecting peripheral devices that support USB 3.1 Gen 1, highspeed data communication is possible (however, only when the USB cable used to connect the external device
and peripheral device supports USB 3.1 Gen 1).
•• The "CHARGE" USB downstream port also supports quick charging. This allows you to recharge your
smartphone or tablet in a short period of time.
•• If the connector for your external device is a Thunderbolt 3/USB Type-C connector, use a USB Type-C - Type-A
converter cable.
38
Chapter 6
Reference
6-7. Specifications
LCD Panel
Type
IPS (Anti-Glare)
Backlight
Wide color gamut LED
Size
61.1 cm (24.1 inch)
Resolution
1920 dots x 1200 lines
Display Size (H x V)
518.4 mm x 324.0 mm
Pixel Pitch
0.270 mm x 0.270 mm
Pixel Density
94 ppi
Display Colors
Approx. 16.77 million colors (8 bit colors)
Viewing Angle (H x V, typical) 178˚ / 178˚
Video Signals
Contrast Ratio (typical)
1000 : 1 (When "DUE Priority" setting is "Brightness")
Response Time (typical)
Gray-to-gray: 14 ms
Color Gamut Display (typical)
sRGB coverage 100%, NTSC ratio 79%
Input Terminals
DisplayPort 1.1a (HDCP 1.3 compatible) x 1,
HDMI (HDCP 1.4, Deep Color compatible)*1 x 1,
DVI (Single Link, HDCP 1.4 compatible) x 1
*1 Not compatible with HDMI CEC function (mutual control
function).
Horizontal scan frequency
DisplayPort: 26 kHz to 78 kHz
HDMI (Video mode): 15 kHz to 68 kHz
HDMI (PC mode): 26 kHz to 78 kHz
DVI: 26 kHz to 78 kHz
Vertical scan frequency
DisplayPort: 23 Hz to 63 Hz (For 720 x 400: 69 Hz to 71 Hz)
HDMI (Video mode): 23 Hz to 61 Hz
HDMI (PC mode): 23 Hz to 63 Hz
HDMI (for 720 x 400): 69 Hz to 71 Hz
DVI: 23 Hz to 63 Hz (For 720 x 400: 69 Hz to 71 Hz)
Frame Synchronization mode 23.75 Hz to 30.5 Hz, 47.5 Hz to 61.0 Hz
USB
Power
Dot clock (Max.)
164 MHz
Port
Upstream
USB Type-B (USB3.1 Gen1) x 1
Downstream
USB Type-A (USB3.1 Gen1) x 3
(The "CHARGE" port supports quick recharging)
Standard
USB Specification Revision 3.1 Gen 1
Communication Speed
5 Gbps (super), 480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low)
Supply Current Downstream
USB Type-A (USB3.1 Gen1): Maximum 900 mA per port
USB Type-A ("CHARGE" Port): Normal: Maximum 1500 mA
per port, Charging Only: Maximum 2100 mA per port
Input
100-240 VAC ±10 %, 50/60 Hz 0.60 A to 0.30 A
Maximum Power Consumption 57 W or less
Power Save Mode
0.7 W or less (this applies when the OS turns to sleep mode or
when the monitor's power off setting is activated, if the monitor
has DisplayPort input signal only, "Auto Input Detection" is set
to "Off", no USB device is connected, and "USB CHARGE
Port" is set to "Normal")
Standby Mode
0.6 W or less (when "Auto Input Detection" is set to "Off",
no USB device is connected, "USB CHARGE Port" is set to
"Normal", and "DP Power Save" is set to "On")
Chapter 6
Reference
39
Physical
Specifications
Outside
Dimensions
Minimum
Height
554.4 mm x 396 mm x 245 mm (W x H x D)
(Tilt: 0˚)
Maximum
Height
554.4 mm x 558 mm x 265 mm (W x H x D)
(Tilt: 35˚)
Outside Dimensions (Without
Stand)
554.4 mm x 362 mm x 64 mm (W x H x D)
Net Weight
Approx. 7.9 kg
Net Weight (Without Stand)
Approx. 5.1 kg
Height adjustment
155 mm (at tilt of 0˚)
Tilt
Up 35˚, down 5˚
Swivel
344°
Vertical rotation
90° clockwise
Operating
Environment
Requirements
Temperature
0˚C to 35˚C
Humidity
20 % to 80 % R.H. (no condensation)
Air Pressure
540 hPa to 1060 hPa
Transportation/
Storage
Environment
Requirements
Temperature
-20 ˚C to 60 ˚C
Humidity
10 % to 90 % R.H. (no condensation)
Air Pressure
200 hPa to 1060 hPa
●●Accessories
For the latest information about the accessories, refer to our website (www.eizoglobal.com).
40
Chapter 6
Reference
Appendix
Trademark
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing, LLC in the United States and other countries.
The DisplayPort Compliance Logo and VESA are registered trademarks of the Video Electronics
Standards Association.
The SuperSpeed USB Trident Logo is a registered trademark of USB Implementers
Forum, Inc.
The USB Power Delivery Trident Logos are trademarks of USB Implementers Forum,
Inc.
DICOM is the registered trademark of the National Electrical Manufacturers Association for its standards
publications relating to digital communications of medical information.
Kensington and Microsaver are registered trademarks of ACCO Brands Corporation.
Thunderbolt is a trademark of Intel Corporation in the United States and/or other countries.
Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and
other countries.
Adobe is a registered trademark of Adobe Systems Incorporated in the United States and other
countries.
Apple, macOS, Mac OS, OS X, Macintosh and ColorSync are registered trademarks of Apple Inc.
EIZO, the EIZO Logo, ColorEdge, CuratOR, DuraVision, FlexScan, FORIS, RadiCS, RadiForce,
RadiNET, Raptor and ScreenManager are registered trademarks of EIZO Corporation in Japan and other
countries.
ColorEdge Tablet Controller, ColorNavigator, EcoView NET, EIZO EasyPIX, EIZO Monitor Configurator,
EIZO ScreenSlicer, G-Ignition, i•Sound, Quick Color Match, RadiLight, Re/Vue, SafeGuard, Screen
Administrator, Screen InStyle, ScreenCleaner and UniColor Pro are trademarks of EIZO Corporation.
All other company names, product names, and logos are trademarks or registered trademarks of their
respective companies.
License
The bitmap font used for this product is designed by Ricoh Industrial Solutions Inc.
Appendix
41
Information for Radio Interference
For U.S.A., Canada Only
FCC Supplier’s Declaration of Conformity
We, the Responsible Party
EIZO Inc.
5710 Warland Drive, Cypress, CA 90630
Phone: (562) 431-5011
declare that the product
Trade name: EIZO
Model: ColorEdge CS2410
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures.
*
*
*
*
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Note
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep interference
within the limits of a Class B digital device.
--AC Cord
--Shielded Signal Cable (enclosed)
Canadian Notice
This Class B information technology equipment complies with Canadian ICES-003.
Cet équipement informatique de classe B est conforme à la norme NMB-003 du Canada.
42
Appendix
03V27723A1
UM-CS2410
Copyright © 2019 EIZO Corporation. All rights reserved.
1st Edition-March, 2019
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising