Eizo | CX240 | User manual | Eizo CX240 User Manual

Eizo CX240 User Manual
Important
Please read PRECAUTIONS, this User’s Manual, and the Setup Guide
(separate volume) carefully to familiarize yourself with safe and
effective usage.
• Please refer to the Setup Guide for basic information ranging from
connection of the monitor to a PC to using the monitor.
• The latest User’s Manual is available for download from our web site:
http://www.eizoglobal.com
Location of Caution Statement
Ex. CS230
WARNING
AVERTISSEMENT
WARNUNG
This product has been adjusted specifically for use in the region to which it was originally shipped. If operated
outside this region, the product may not perform as stated in the specifications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information confidential unless prior
arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every effort has been
made to ensure that this manual provides up-to-date information, please note that EIZO monitor specifications are
subject to change without notice.
2

Notice for this monitor
Aside from general purposes like creating documents, viewing multimedia content, this product is also suited to
applications such as creations of images and graphics, and digital photo processing, where accurate color reproduction
is a priority.
This product has been adjusted specifically for use in the region to which it was originally shipped. If the product is
used outside the region, it may not operate as specified in the specifications.
This product may not be covered by warranty for uses other than those described in this manual.
The specifications noted in this manual are only applicable when the following are used:
· Power cords provided with the product
· Signal cables specified by us
Only use optional products manufactured or specified by us with this product.
If you place this product on a lacquer-coated desk, the color may adhere to the bottom of the stand due to the
composition of the rubber. Check the desk surface before use.
As it takes about 30 minutes (CS230) / 7 minutes (CS240: under our measurement conditions) for the performance of
electrical parts to stabilize. Please wait 30 minutes (CS230) / 7 minutes (CX240) or more after the monitor power has
been turned on, and then adjust the monitor.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and maintain a
stable display.
When the screen image is changed after displaying the same image for extended periods of time, an afterimage may
appear. Use the screen saver or power save function to avoid displaying the same image for extended periods of time.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer to
“Cleaning” (page 4)).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may appear on
the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994% or higher.
The backlight of the LCD panel has a fixed lifetime. When the screen becomes dark or begins to flicker, please contact
your local EIZO representative.
Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions, such as interference
patterns, etc. If pressure is continually applied to the panel, it may deteriorate or damage your panel. (If the pressure
marks remain on the panel, leave the monitor with a black or white screen. The symptom may disappear.)
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do not attempt
to brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may
occur on the interior and exterior surfaces of the monitor. In that case, do not turn the monitor on. Instead wait until
the dew condensation disappears, otherwise it may cause some damage to the monitor.
Notice for this monitor
3
Cleaning
Attention
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or panel,
and also quality deterioration of the image.
• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.
Note
• The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface.
If necessary, the stains on the cabinet and panel surface can be removed by moistening part of a soft cloth with
water.
To use the monitor comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according to
the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
4
Notice for this monitor
CONTENTS
Notice for this monitor.......................................... 3
Cleaning..................................................................... 4
To use the monitor comfortably.............................. 4
CONTENTS.............................................................. 5
Chapter 1
Introduction........................................ 7
1-1.
Features.......................................................... 7
1-2.
Controls and Functions................................ 9
1-3.
EIZO LCD Utility Disk...................................10
●●Disk contents and software overview.............10
●●To use ColorNavigator / ColorNavigator
2-9.
Setting HDMI................................................. 32
●●Reducing Noise.............................................. 32
Chapter 3
Setting Monitor................................ 33
Setting Orientation...................................... 33
3-4.
Changing Adjustment Menu Display
Position......................................................... 34
3-5.
Showing and Hiding the EIZO Logo.......... 34
Adjusting Screens........................... 15
3-6.
Locking Operation Button.......................... 34
Compatible Resolutions..............................15
3-7.
Setting Signal Bandwidth........................... 35
3-8.
Switching USB Port Automatically............ 35
3-9.
Changing DUE
(Digital Uniformity Equalizer) Setting....... 36
Setting the Resolution.................................16
Adjusting Color.............................................18
●●To select the display mode (color mode)........18
●●To perform advanced adjustments.................19
●●Adjustable settings in each mode...................19
●●Adjusting Brightness...................................... 20
●●Adjusting the temperature.............................. 20
●●Adjusting Gamma............................................21
●●Adjusting Hue..................................................21
●●Adjusting Saturation....................................... 22
●●To enable/disable Contrast Enhancer............ 22
●●To enhance outline of image.......................... 22
●●To set clipping................................................ 23
●●Adjusting Gain.................................................24
●●Adjusting 6 Colors...........................................24
Adjusting Screens....................................... 25
●●
●●
2-5.
Specifying Color Space.............................. 32
3-3.
Basic Operations and Functions................11
●●Windows 10.....................................................16
●●Windows 8.1 / Windows 7...............................16
●●Windows Vista.................................................16
●●Windows XP....................................................16
●●OS X Mountain Lion (10.8) and later...............17
●●Mac OS X 10.7................................................17
2-4.
2-8.
Selecting the Language.............................. 33
●●Analog Input (DVI-I)........................................15
●●Digital Input (DVI / DisplayPort) .....................15
●●Digital Input (HDMI).........................................15
2-3.
Configuring Moving Image Performance....31
3-2.
Chapter 2
2-2.
2-7.
●●DVI, DisplayPort signal input......................... 29
●●HDMI (HD signal) input.................................. 30
●●HDMI (SD signal) input...................................31
Enabling/Disabling Mode Selection.......... 33
●●Basic Adjustment menu operations................11
●●Showing Button Guide....................................12
●●Functions.........................................................13
2-1.
Selecting Screen Size................................. 29
3-1.
Elements.........................................................10
1-4.
2-6.
3-10. Reset to default............................................ 36
●●To reset the color adjustments....................... 36
●●To reset all adjustments to the default
settings............................................................37
Chapter 4
4-1.
SelfCorrection.................................. 38
Executing SelfCorrection........................... 38
Chapter 5
Power Saving Functions................. 39
5-1.
Setting Power Save...................................... 39
5-2.
Enabling/Disabling Automatic
Brightness Adjustment............................... 40
5-3.
Checking the Power Saving Level............. 40
5-4.
Adjusting the Brightness of Indicator....... 40
5-5.
Setting USB Power Save..............................41
5-6.
Setting DisplayPort Power Save.................41
Chapter 6
Troubleshooting............................... 42
6-1.
No picture..................................................... 42
6-2.
Imaging problems........................................ 43
6-3.
Other problems............................................ 44
6-4.
Built-in correction sensor and
SelfCorrection problems............................ 45
Digital Signal Input......................................... 25
Analog Signal Input........................................ 25
Chapter 7
Expanding Signal Output Range............... 28
7-2.
7-1.
Reference......................................... 46
Attaching the Optional Arm........................ 46
Connecting Multiple External Devices.......47
●●
●●
To switch among input signals....................... 48
To set input signal selection “Input
Selection”....................................................... 48
CONTENTS
5
7-3.
Making Use of USB
(Universal Serial Bus).................................. 49
●●System Requirement...................................... 49
●●Procedure....................................................... 49
7-4.
Showing Monitor Information.................... 50
●●Displaying signal information “Signal Info”.... 50
●●Displaying Monitor Information “Monitor
Info”................................................................ 50
7-5.
Specifications...............................................51
7-6.
Preset Timing............................................... 55
7-7.
Glossary........................................................ 56
●●CS230.............................................................51
●●CX240.............................................................52
Appendix............................................................... 58
Trademark................................................................ 58
License..................................................................... 58
FCC Declaration of Conformity............................. 59
LIMITED WARRANTY.............................................. 60
Recycling Information............................................ 69
6
CONTENTS
Chapter 1 Introduction
1-1. Features
•
•
•
•
•
•
•
•
23.0″ wide format LCD (CS230)
24.1″ wide format LCD (CX240)
Wide color gamut (Adobe RGB coverage: 97%, CX240 only)
Supports a resolution of 1920 × 1080 (CS230).
Supports a resolution of 1920 × 1200 (CX240).
IPS panel with 178˚ horizontal and vertical viewing angles
Frame synchronization mode supported (23.75 - 30.5Hz, 47.5 - 61.0Hz)
3 signal input terminals (DVI-I × 1, HDMI × 1, DisplayPort × 1)
-- DisplayPort connector (applicable to 8 bit and 10 bit)*1
-- HDMI connector (applicable to 8 bit, 10 bit, and 12 bit)*1
*1 Not applicable to audio signals.
• Color Mode function
Reproduces a color gamut and gamma compliant with the following standard.
-- Adobe®RGB (CX240 only)
The Paper mode reproduces a printed paper effect on the monitor.
See “To select the display mode (color mode)” (page 18).
• Supports portrait and landscape format (rotate 90˚ clockwise)
• This product is equipped with a built-in correction sensor, and supports SelfCorrection in which the monitor
executes display correction independently.
See “Chapter 4 SelfCorrection” (page 38).
• The “ColorNavigator” Color Management Software enables you to calibrate monitor characteristics and
generate color profiles*2
*2 The Color Management Software “ColorNavigator” is on the CD-ROM for the ColorNavigator Licensed models.
See “1-3. EIZO LCD Utility Disk” (page 10).
• Supports Photo Color Matching Software “ColorNavigator Elements”*3
This software enables you to adjust the color of the monitor easily while comparing it with a printed picture.
*3 Stored on the CD-ROM for the ColorNavigator non-licensed models. See “1-3. EIZO LCD Utility Disk” (page 10).
• The software “ScreenManager Pro for LCD” to adjust the screen using the mouse and keyboard is included.
This software can be downloaded from our web site (http://www.eizoglobal.com).
• Supports Color Vision Deficiency Simulation Software “UniColor Pro”
This software can be downloaded from our web site (http://www.eizoglobal.com).
• Power saving function
Suppressing the power consumption reduces the carbon dioxide emissions. This product is equipped with power saving
function.
-- 0 W power consumption when the main power is off
Equipped with main power switch.
When the monitor is not required, the power supply can be shut off using the main power switch.
-- Auto EcoView function
The ambient light sensor on the front side of the monitor detects the environmental brightness to adjust the screen
brightness automatically and comfortably. Excessively high brightness may increase power consumption and cause
unwanted environmental effects. It may also lead to fatigue of your eyes. Use the Auto EcoView to reduce the
brightness.
See “5-2. Enabling/Disabling Automatic Brightness Adjustment” (page 40).
• Displays HDCP (High-bandwidth Digital Protection) protected contents.
Chapter 1 Introduction
7
Attention
Be careful of the following points when using the built-in correction sensor.
Do not touch the built-in correction sensor.
It may reduce the measurement accuracy of the built-in correction sensor, or result in injury
or equipment damage.
Attention
• A high temperature or high humidity environment may affect the measurement accuracy of the built-in correction
sensor. We suggest storing and using the monitor under the following conditions.
- Temperature 30˚C or less
- Humidity 70% or less
Avoid storing or using the sensor where it may be exposed to direct sunlight.
Note
• This monitor supports both portrait and landscape format. You can change the orientation of the Setting menu when
using the monitor screen in vertical display position. (see “3-3. Setting Orientation” (page 33))
• When using the monitor screen in a portrait position, the graphics board supporting portrait display is required. When
placing the monitor in a portrait position, the settings of your graphics board need to be changed. Refer to the User’s
Manual of the graphics board for details.
8
Chapter 1 Introduction
1-2. Controls and Functions
1
Adjustment
menu*1
15
16
17
2
3
4
5
6
1. Built-in correction sensor
2. Ambient Light Sensor
button
3.
4.
button
button
5.
6.
button
7.
8.
button
button
7
8 9
1011
12 1314
Executes display correction for an independent monitor. SelfCorrection function
(page 38)
Measures ambient light.
Switches input signals for display (page 48).
Changes Color Mode (page 18).
Cancels the setting/adjustment and exits the Adjustment menu.
• Provides the menu selection as well as the adjustment and setting of a function.
• Displays the Brightness menu (page 20).
Displays the Adjustment menu, determines an item on the menu screen, and saves
values adjusted (page 11).
Turns the power on or off.
Indicates the monitor’s operation status.
9. Power Indicator
Blue:
Operating
Flashing blue 
(2 times for each):
In the following cases, this notifies that display re-correction
is required.
• When the timer is set in ColorNavigator (CAL mode)
• When the SelfCorrection schedule is set
Orange:
Power saving mode
OFF:
Main power/Power off
10. Main power switch
Turns the main power on or off.
11. Power connector
Connects the power cord.
12. Input signal connectors
Left: DVI-I connector / Center: HDMI connector / Right: DisplayPort connector
Connects the USB cable to use the software that needs USB connection, or to use
USB hub function (page 49).
13. USB upstream port
Attention
• By default, USB upstream port 1 is enabled. Connect the cable to USB upstream port 1
first.
14. USB downstream port
15. Stand
*2
Connects a peripheral USB device.
Used to adjust the height and angle of the monitor screen.
16. Security lock slot
Complies with Kensington’s MicroSaver security system.
17. Cable holder
Covers the monitor cables.
*1 For details, see “1-4. Basic Operations and Functions” (page 11).
*2 An optional arm (or an optional stand) can be attached by removing the stand section (see “7-1. Attaching the Optional Arm”
(page 46)).
Chapter 1 Introduction
9
1-3. EIZO LCD Utility Disk
An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk contents
and the overview of the software programs.
●●Disk contents and software overview
The disk includes application software programs for adjustment, and User’s Manual. Refer to “Readme.txt” or
the “read me” file on the disk for software startup procedures or file access procedures.
Contents
Overview
Windows
Macintosh
√
√
Software for calibrating monitor characteristics
and generating ICC profiles (for Windows) and
Apple ColorSync profiles (for Macintosh).
(A PC must be connected to the monitor with
the supplied USB cable.)
√
√
Software for adjusting the color and brightness
of the monitor while comparing a picture
displayed on the monitor with a printed picture.
(A PC must be connected to the monitor with
the supplied USB cable.)
√
√
Used when adjusting the image of the analog
signal input manually.
√
-
√
√
A “Readme.txt” or “read me” file
ColorNavigator
*1
ColorNavigator Elements*2
Screen adjustment pattern files
User’s Manual of this monitor (PDF file)
*1 Only ColorNavigator Licensed models
*2 Only ColorNavigator Non-Licensed models
●●To use ColorNavigator / ColorNavigator Elements
The method of displaying the defined color gamut outside the normal gamut of the monitor can be set.
Attention
• If “ColorNavigator License” in the monitor information screen is “Not Registered”, the ColorNavigator license must be
purchased and registered to the monitor. For the purchase of the license, contact your local EIZO representative.
• ColorNavigator Elements can be used without a license.
Refer to the corresponding User’s Manual on the CD-ROM disk in order to install and use the software.
When using this software, you will need to connect a PC to the monitor with the supplied USB cable. For
details of the USB cable connection, see “7-3. Making Use of USB (Universal Serial Bus)” (page 49).
10
Chapter 1 Introduction
1-4. Basic Operations and Functions
●●Basic Adjustment menu operations
1. Displaying Adjustment Menu
1. Press
. The Adjustment menu appears.
Menu title
Current mode
Item
Setting
Menu
2. Adjusting/Setting
1. Choose a menu to adjust/set with , , and then press
.
2. Choose an item to adjust/set with , , and then press
.
3. Adjust/set the selected item with , , and then press
.
3. Exiting the software
1. Press
a few times. The Adjustment menu finishes.
Chapter 1 Introduction
11
●●Showing Button Guide
Press the front buttons (except button), the button guide appears above the button. (When using the monitor
with “Portrait” position, the button guide appears next to the button.)
Button Guide
Control button
Note
• The button guide will continue to appear while the Adjustment menu or Mode menu is showing.
• The button guide is displayed differently depending on the selected menu or status.
• In CAL mode, although Button Guide are displayed above the and buttons, the brightness cannot be adjusted.
12
Chapter 1 Introduction
●●Functions
The following table shows the menus for adjustment and setting items of each menu.
Main Menu
Color*1
Item
Reference
“2-3. Adjusting Color” (page 18)
Brightness
Temperature
Gamma
Advanced
Settings
Hue
Saturation
Contrast
Enhancer
Outline Enhancer
Clipping
Gain
6 Colors
Color Reset
“3-10. Reset to default” (page 36)
SelfCorrection
Execute
“4-1. Executing SelfCorrection” (page 38)
Screen
Screen Size
“2-6. Selecting Screen Size” (page 29)
Overdrive
“2-7. Configuring Moving Image
Performance” (page 31)
Color Space
“2-8. Specifying Color Space” (page 32)
Range Extension
“2-5. Expanding Signal Output Range” (page
28)
HDMI Settings*2
Analog
Adjustment*3
Noise Reduction
“2-9. Setting HDMI” (page 32)
Auto Adjustment
“2-4. Adjusting Screens” (page 25)
Range Adjustment
Clock
Phase
Hor. Position
Ver. Position
Power 
Manager
Menu Settings
Power Save
“5-1. Setting Power Save” (page 39)
Auto EcoView
“5-2. Enabling/Disabling Automatic
Brightness Adjustment” (page 40)
Indicator
“5-4. Adjusting the Brightness of Indicator”
(page 40)
EcoView Index
“5-3. Checking the Power Saving Level”
(page 40)
Language
“3-2. Selecting the Language” (page 33)
Orientation
“3-3. Setting Orientation” (page 33)
Menu Position
“3-4. Changing Adjustment Menu Display
Position” (page 34)
Chapter 1 Introduction
13
Tools
Input Selection
“To switch among input signals” (page 48)
Mode Preset
“3-1. Enabling/Disabling Mode Selection” (page
33)
USB
Selection
DVI
“3-8. Switching USB Port Automatically” (page 35)
DisplayPort
HDMI
Signal Info
“7-4. Showing Monitor Information” (page 50)
Monitor Info
All Reset
“3-10. Reset to default” (page 36)
*1 The adjustment/settings available on the “Color” menu depend on the selected mode. (See “2-3. Adjusting Color”
(page 18))
*2 This setting can be adjusted with HDMI signal input.
*3 These functions can be adjusted with analog input.
14
Chapter 1 Introduction
Chapter 2 Adjusting Screens
2-1. Compatible Resolutions
The monitor supports the following resolutions.
●●Analog Input (DVI-I)
Resolution
Applicable Signals
640 × 480
720 × 400
800 × 600
1024 × 768
1280 × 960
1280 × 1024
1600 × 1200
1680 × 1050
1920 × 1080*1
1920 × 1080*1
1920 × 1200 *2
VGA
VGA TEXT
VESA
VESA
VESA
VESA
VESA
VESA CVT, VESA CVT RB
VESA CVT RB
CEA-861
VESA CVT RB
Vertical scan
frequency
60 Hz
70 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
Dot clock
(Max.)
CS230
CX240
149.0 MHz
(CS230)
164.5 MHz
(CX240)
√
√
√
√
√
√
√
√
√
-
√
√
√
√
√
√
√
√
√
√
Dot clock
(Max.)
CS230
CX240
√
√
√
√
√
√
√
√
-
√
√
√
√
√
√
√
√
√
√
●●Digital Input (DVI / DisplayPort)
Resolution
Applicable Signals
640 × 480
720 × 400
800 × 600
1024 × 768
1280 × 960
1280 × 1024
1600 × 1200
1680 × 1050
1920 × 1080 *1
1920 × 1200 *2
VGA
VGA TEXT
VESA
VESA
VESA
VESA
VESA
VESA CVT, VESA CVT RB
VESA CVT RB
VESA CVT RB
Vertical scan
frequency
60 Hz
70 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
149.0 MHz
(CS230)
164.5 MHz
(CX240)
●●Digital Input (HDMI)
• Video signal
-- VGA / 480i,480p,1080i,720p,1080p: 60 Hz
-- 576i,576p,1080i,720p,1080p: 50 Hz
-- 1080p: 24 Hz, 25 Hz, 30 Hz
The graphics board should comply with the VESA standard and CEA-861 standard.
See “3-7. Setting Signal Bandwidth” (page 35).
*1 Recommended resolution (CS230)
*2 Recommended resolution (CX240)
Chapter 2 Adjusting Screens
15
2-2. Setting the Resolution
When you connect the monitor to the PC and find that the resolution is improper, or when you want to change the
resolution, follow the procedure below.
●●Windows 10
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Display Settings”.
3. On the “Customize your display” dialog box, click “Advanced display settings”.
4. Select a monitor, then choose a resolution from the “Resolution” pull-down menu.
5. Click the “Apply” button.
6. When a confirmation dialog box is displayed, click “Keep changes”.
●●Windows 8.1 / Windows 7
1. For Windows 8.1, click the “Desktop” tile on the Start Screen to display the desktop.
2. Right-click the mouse anywhere on the desktop except for icons.
3. From the displayed menu, click “Screen resolution”.
4. On the “Screen Resolution” dialog box, select the monitor.
5. Click “Resolution” to select the desired resolution.
6. Click the “OK” button.
7. When a confirmation dialog box is displayed, click “Keep changes”.
●●Windows Vista
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Personalize”.
3. On the “Personalization” window, click “Display Settings”.
4. On the “Display Settings” dialog box, select the “Monitor” tab and select desired resolution in the
“Resolution” field.
5. Click the “OK” button.
6. When a confirmation dialog box is displayed, click “Yes”.
●●Windows XP
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Properties”.
3. When the “Display Properties” dialog box is displayed, click the “Settings” tab and select desired resolution
for “Screen resolution” under “Display”.
4. Click the “OK” button to close the dialog box.
16
Chapter 2 Adjusting Screens
●●OS X Mountain Lion (10.8) and later
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog box is displayed, click “Displays”. (For Mac OS X Mountain Lion
(10.8), click “Displays” for “Hardware”.)
3. On the displayed dialog box, select the “Display” tab, then choose “Change” for “Resolutions”.
4. The list of selectable resolutions is displayed. Select the desired resolution.
If the desired resolution is not displayed in the list, hold down the Option key and select “Change”.
5. Your selection will be reflected immediately.
6. When you are satisfied with the selected resolution, close the window.
●●Mac OS X 10.7
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.
3. On the displayed dialog box, select the “Display” tab and select desired resolution in the “Resolutions” field.
4. Your selection will be reflected immediately. When you are satisfied with the selected resolution, close the
window.
Chapter 2 Adjusting Screens
17
2-3. Adjusting Color
●●To select the display mode (color mode)
This function allows easy selection of a desired mode according to monitor application.
Display Modes
Mode
CS230
Purpose
CX240
1-User1
1-User1
2-User2
2-User2
Available for the color settings according to your preference.
3-User3
3-User3
4-Paper
4-Paper
Produces a printed paper effect. Suitable for displaying images from media such
as books and documents.
-
5-Adobe® RGB
Suitable for color matching with Adobe ® RGB compatible peripherals.
5-sRGB
6-sRGB
Suitable for color matching with sRGB compatible peripherals.
6-CAL
7-CAL
Displays the screen adjusted by “ColorNavigator” Color Management Software
and “ColorNavigator Elements” Photo Color Matching Software.
Note
• In CAL mode, ColorNavigator and ColorNavigator Elements can be used for adjustment.
• Available CAL mode differs depending on each input signal.
Attention
• Avoid operating any function of the monitor while using ColorNavigator and/or ColorNavigator Elements. Regarding
ColorNavigator and ColorNavigator Elements, see “To use ColorNavigator / ColorNavigator Elements” (page 10).
Example: At DVI input (CX240)
The mode menu
appears.
1-User1←→2-User2←→3-User3←→4-Paper
7-CAL←→6-sRGB←→5-Adobe ® RGB
Procedure
1. Press
.
The mode menu appears at the bottom left of the screen.
2. The mode among the list is highlighted in turn each time
You can switch the mode with
or
is pressed.
while the mode menu is displayed.
Note
• The Adjustment menu and the Mode menu cannot be displayed at the same time.
• You can disable a specific mode to be selected. For more information, see “3-1. Enabling/Disabling Mode Selection”
(page 33).
• “ScreenManager Pro for LCD” allows you to select the color mode automatically according to the application used (see
“Chapter 3 Auto FineContrast” in the “ScreenManager Pro for LCD” User’s Manual).
18
Chapter 2 Adjusting Screens
●●To perform advanced adjustments
“Color” of the Adjustment menu allows you to configure and save a separate set of color settings for each
mode.
Attention
• As it takes about 30 minutes (CS230) / 7 minutes (CS240: under our measurement conditions) for the performance of
electrical parts to stabilize. Please wait 30 minutes (CS230) / 7 minutes (CX240) or more after the monitor power has
been turned on, and then adjust the monitor.
• Perform the range adjustment first when adjusting color for analog signals (see “To adjust color gradation automatically”
(page 28)).
• The same image may be seen in different colors on multiple monitors due to their monitor-specific characteristics. Make
fine color adjustment visually when matching colors on multiple monitors.
Note
• The values shown in “%” or “K” are available only as reference.
• Using the “ScreenManager Pro for LCD” allows you to perform the color adjustment by using the mouse and
keyboard of your PC. The adjusted conditions can be stored as the color data to be read in later. (See “Chapter 4 Color
Adjustment” in the User’s Manual for “ScreenManager Pro for LCD”.)
• Using ColorNavigator enables the monitor adjustment that prioritizes color matching of multiple monitors. For details,
refer to the ColorNavigator User’s Manual.
●●Adjustable settings in each mode
The adjustable settings depend on the mode. (You cannot select any non-adjustable or non-settable function.)
The adjustments or settings made for each mode are applied to all input signals.
√: Adjustable -: Not adjustable
Color Mode
CS230
1-User1
2-User2
3-User3
4-Paper
-
5-sRGB
6-CAL
CX240
1-User1
2-User2
3-User3
4-Paper
5-Adobe® RGB
6-sRGB
7-CAL
Brightness
√
√
√
√
√
√
-
Temperature
√
√
√
√
√
√
-
Gamma
√
√
√
-
√
√
-
Hue
√
√
√
-
-
-
-
Saturation
√
√
√
-
-
-
-
Contrast Enhancer
√
√
√
-
-
-
-
Outline Enhancer
√
√
√
√
√
√
-
Clipping
-
-
-
-
√
√
-
Gain
√
√
√
-
-
-
-
6 Colors
√
√
√
-
-
-
-
Function
Chapter 2 Adjusting Screens
19
●●Adjusting Brightness
The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD back
panel).
Setting Range
50 cd/m 2 to 300 cd/m2
Procedure
1. Press
or .
The Brightness menu appears.
2. Use
or
for adjustment.
to exit.
3. Press
Attention
• If the entered value cannot be set, the value will appear in magenta. In such a case, change the value.
Note
• Alternatively, you can use “Brightness” under “Color” in the Adjustment menu to adjust it.
• The values shown in “cd/m 2” are available only as reference.
●●Adjusting the temperature
The color temperature can be adjusted.
The color temperature is normally used to express the hue of “White” and/or “Black” by a numerical value.
The value is expressed in degrees “K” (Kelvin).
The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like the flame
temperature. The gain preset values are set for each color temperature setting value.
Setting Range
Native, 4000K-10000K (specified every 100K), Standard
Procedure
.
1. Choose “Color” from the Adjustment menu, and press
2. Choose “Temperature” from “Color”, and press
3. Use
4. Press
or
.
for adjustment.
to exit.
Note
•
•
•
•
20
“Gain” allows you to perform more advanced adjustment (see “Adjusting Gain” (page 24)).
If you set “Native”, the image is displayed in the preset color of the monitor (Gain: 100% for each RGB).
When gain is changed, the color temperature is changed to “User”.
The default setting for each Adobe®RGB(CX240 only)/sRGB mode is set to “Standard”, which is the temperature in
conformity with each standard.
Chapter 2 Adjusting Screens
●●Adjusting Gamma
Gamma can be adjusted. The brightness of the monitor varies depending on the input signal, however, the
variation rate is not proportional to the input signal. To keep the balance between the input signal and the
brightness of the monitor is called as “Gamma correction”.
Setting Range
1.6-2.7, Standard
Procedure
.
1. Choose “Color” from the Adjustment menu, and press
2. Choose “Gamma” from “Color”, and press
3. Use
or
.
for adjustment.
to exit.
4. Press
Note
• The default setting for each Adobe®RGB(CX240 only)/sRGB mode is set to “Standard”, which is the gamma in
conformity with each standard.
• The gamma curve can be adjusted to L* by using ColorNavigator. For details, refer to the ColorNavigator User’s
Manual.
●●Adjusting Hue
This function allows you to adjust the hue.
Setting Range
-100 to 100
Procedure
.
1. Choose “Color” from the Adjustment menu, and press
2. Choose “Advanced Settings” from “Color”, and press
3. Choose “Hue”, and press
4. Use
5. Press
or
.
.
for adjustment.
to exit.
Attention
• Using this function may make some color gradations unavailable for display.
Chapter 2 Adjusting Screens
21
●●Adjusting Saturation
This function allows you to adjust color saturation.
Setting Range
-100 to 100
Procedure
.
1. Choose “Color” from the Adjustment menu, and press
2. Choose “Advanced Settings” from “Color”, and press
3. Choose “Saturation”, and press
4. Use
or
5. Press
.
.
for adjustment.
to exit.
Attention
• Using this function may make some color gradations unavailable for display.
Note
• The minimum value (-100) changes the screen to monochrome.
●●To enable/disable Contrast Enhancer
This feature manages the brightness and gain levels of the backlight to match the image displayed while also
improving the sense of contrast of images by correcting gamma values.
Procedure
.
1. Choose “Color” from the Adjustment menu, and press
2. Choose “Advanced Settings” from “Color”, and press
.
3. Choose “Contrast Enhancer”, and press
4. Select “On” or “Off” with
5. Press
.
or .
to exit.
●●To enhance outline of image
OutlineEnhancer functions to emphasize outline of the images by emphasizing the color difference between
pixels composing the images. This may improve the texture of the material and its feel of the images. On the
contrary, it also functions to reproduce the images smoothly by gradating its outline.
Procedure
.
1. Choose “Color” from the Adjustment menu, and press
2. Choose “Advanced Settings” from “Color”, and press
3. Choose “Outline Enhancer”, and press
.
.
4. Select the display status in the range from -3 to 3 (soft to sharp) with
5. Press
22
to exit.
Chapter 2 Adjusting Screens
or
as desired.
●●To set clipping
This function allows you to display the monitor with the colors based on the standard values of the defined
color gamut (such as sRGB). The method of displaying the defined color gamut outside the normal gamut of the
monitor can be set.
Procedure
.
1. Choose “Color” from the Adjustment menu, and press
2. Choose “Advanced Settings” from “Color”, and press
3. Choose “Clipping”, and press
4. Select “On” or “Off” with
.
.
or .
On:
Displays colors based on the standard values.
The colors outside the gamut of the monitor are
clipped.
Off:
Displays colors with priority on the color gradation
rather than the color accuracy.
The primary colors outside the gamut of the monitor
(blue in the diagram) are adjusted to the colors most
similar to those that can be displayed by the monitor.
Color gamut of monitor
Color gamut defined by standard
Color gamut displayed on screen
Attention
• This is a conceptual diagram, and does not display the actual color gamut of the monitor.
5. Press
to exit.
Attention
• This function can be set only in the color mode specified by the color gamut standard.
Chapter 2 Adjusting Screens
23
●●Adjusting Gain
The brightness of each color component red, green, and blue is called Gain. You can change the hue of “white”
by adjusting gain.
Setting Range
0% to 100%
Procedure
.
1. Choose “Color” from the Adjustment menu, and press
2. Choose “Advanced Settings” from “Color”, and press
3. Choose “Gain”, and press
.
.
4. Choose the color for adjustment from “Red”, “Green”, and “Blue”, and press
5. Use
or
.
for adjustment.
to exit.
6. Press
Attention
• Using this function may make some color gradations unavailable for display.
Note
• The “Temperature” setting invalidates this setting.
• The value of gain changes with that of color temperature.
• When gain is changed, the color temperature is changed to “User”.
●●Adjusting 6 Colors
The hue and saturation can be adjusted for each of six colors: Magenta, Red, Yellow, Green, Cyan, and Blue.
Adjustable Range
-100 to 100
Procedure
.
1. Choose “Color” from the Adjustment menu, and press
2. Choose “Advanced Settings” from “Color”, and press
3. Choose “6 Colors”, and press
.
.
4. Choose the color for adjustment from “Magenta”, “Red”, “Yellow”, “Green”, “Cyan”, and “Blue”, and press
.
5. Select “Hue” or “Saturation”, and press
6. Use
7. Press
24
or
for adjustment.
to exit.
Chapter 2 Adjusting Screens
.
2-4. Adjusting Screens
●●Digital Signal Input
When digital signals are input, images are displayed correctly based on the preset data of the monitor, but if
you perform more advanced adjustment, see “2-3. Adjusting Color” (page 18) and subsequent pages.
●●Analog Signal Input
Attention
• As it takes about 30 minutes (CS230) / 7 minutes (CS240: under our measurement conditions) for the performance of
electrical parts to stabilize. Please wait 30 minutes (CS230) / 7 minutes (CX240) or more after the monitor power has
been turned on, and then adjust the monitor.
• The Self Adjust (automatic screen adjustment) function does not work for the images under the resolution of 800 × 600
(SVGA).
• The self adjustment and auto adjustment functions work correctly when an image is fully displayed over the Windows
or Macintosh display area. They do not work properly in the cases below:
- when an image is displayed only on a part of the screen (command prompt window, for example)
- when a black background (wallpaper, etc.) is in use
Also, these functions cannot work properly in some graphic boards.
The monitor screen adjustment is used to suppress flickering of the screen or adjust screen position and screen
size correctly according to the PC to be used.
Note
• The self adjustment function works when all of the following conditions are satisfied:
- When a signal is input into the monitor for the first time or when a resolution or vertical/horizontal scan frequency not
used before is set
If the screen is not displayed correctly even after performing the self adjustment operation, adjust the screen
according to the procedures on the following pages to use the monitor comfortably.
How to Set
1. Perform the auto adjustment.
●●To adjust flickering, screen position, and screen size automatically
Procedure
1. Choose “Screen” from the Adjustment menu, and press
.
2. Choose “Analog Adjustment” from “Screen”, and press
.
3. Choose “Auto Adjustment” from “Analog Adjustment”, and press
.
Flickering, screen position, and screen size are corrected by the auto-adjustment function.
If the screen is not displayed correctly even after performing Auto Adjustment, perform the adjustments
according to the procedures on the following pages. If the screen is displayed correctly, go to “To enhance
outline of image” (page 22).
Chapter 2 Adjusting Screens
25
2. Prepare to use analog screen adjustment patterns.
Load the “EIZO LCD Utility Disk” to your PC, and then open the “Screen adjustment pattern files”.
Note
• For details and instructions on opening the “Screen adjustment pattern files”, refer to the Readme.txt file.
3. Perform the auto adjustment again with the analog screen adjustment pattern
displayed.
●●To adjust flickering, screen position, and screen size automatically
Procedure
1. Display Pattern 1 in full screen on the monitor using the “Screen adjustment pattern files”.
2. Choose “Screen” from the Adjustment menu, and press
.
3. Choose “Analog Adjustment” from “Screen”, and press
.
4. Choose “Auto Adjustment” from “Analog Adjustment”, and press
.
Flickering, screen position, and screen size are corrected by the auto-adjustment function.
If the screen is not displayed correctly even after performing Auto Adjustment, perform the adjustments
according to the procedures on the following pages. If the screen is displayed correctly, go to “To enhance
outline of image” (page 22).
4. Choose “Screen” from the Adjustment menu to perform advanced
adjustments.
Adjust the clock, phase and position, in this order.
●●To eliminate vertical bars
Procedure
.
1. Choose “Analog Adjustment” from “Screen”, and press
2. Choose “Clock” from “Analog Adjustment”, and press
.
The “Clock” menu appears.
3. Adjust the clock with
Press
4. Press
or
or
to eliminate vertical bars.
slowly so as not to miss the adjustment point.
to exit.
When blurring, flickering or bars appear on the screen after adjustment, proceed to “To remove flickering or blurring”.
26
Chapter 2 Adjusting Screens
●●To remove flickering or blurring
Procedure
.
1. Choose “Analog Adjustment” from “Screen”, and press
2. Choose “Phase” from “Analog Adjustment”, and press
.
The “Phase” menu appears.
3. Adjust the phase with
4. Press
or
to minimize flickering or blurring.
to exit.
When vertical bars appear on the screen after adjustment, go back to “To eliminate vertical bars”.
(Clock → Phase → Position)
Attention
• Flickering or blurring may not be eliminated depending on your PC or graphics board.
●●To correct the screen position
Note
• Since the number of pixels and the pixel positions are fixed on the LCD monitor, only one position is provided to display
images correctly. The position adjustment is made to shift an image to the correct position.
Procedure
1. Choose “Analog Adjustment” from “Screen”, and press
.
2. Choose “Hor. Position” or “Ver. Position” from “Analog Adjustment”, and press
.
The “Hor.Position” or “Ver.Position” menu appears.
3. Adjust the position with
4. Press
or .
to exit.
5. Close Pattern 1.
Chapter 2 Adjusting Screens
27
5. Adjusting color gradation.
●●To adjust color gradation automatically
Every color gradation (0 to 255) can be displayed by adjusting the signal output level.
Procedure
1. Display Pattern 2 in full screen on the monitor using the “Screen adjustment pattern files”.
2. Choose “Screen” from the Adjustment menu, and press
.
3. Choose “Analog Adjustment” from “Screen”, and press
.
4. Choose “Range Adjustment” from “Analog Adjustment”, and press
.
The output range is set automatically.
5. Close Pattern 2.
2-5. Expanding Signal Output Range
The output range of the signal is extended from 16 - 254 to 0 - 255 for display. When images are displayed in black
and white within the restricted range for purposes such as image creation, use this setting to improve the contrast
of the images.
Procedure
.
1. Choose “Screen” from the Adjustment menu, and press
2. Choose “Range Extension” from “Screen”, and press
3. Select “On”, “Off”, or “Auto” with
or .
Attention
• When the DVI signal is input, “Auto” cannot be selected.
4. Press
28
to exit.
Chapter 2 Adjusting Screens
.
2-6. Selecting Screen Size
The image with the resolution other than the recommended resolution is displayed in full screen automatically.
You can change the screen size by using the “Screen Size” function from “Screen”.
●●DVI, DisplayPort signal input
Settings
Function
Full
Displays an image in full screen. Images are distorted in some cases because the vertical
rate is not equal to the horizontal rate.
Enlarged
Displays an image in full screen. In some cases, a blank horizontal or vertical border
appears to equalize the vertical rate and the horizontal rate.
Normal
Displays images with the specified resolution.
Example: Image size 1280 × 1024
CS230
CX240
Full
Enlarged
Normal
1920 × 1080
1920 × 1200
1350 × 1080
1500 × 1200
1280 × 1024
1280 × 1024
Procedure
.
1. Choose “Screen” from the Adjustment menu, and press
2. Choose “Screen Size” from “Screen”, and press
3. Select “Full”, “Enlarged”, or “Normal” with
4. Press
.
or .
to exit.
Attention
• Selecting “Normal” may make some color gradations unavailable for display.
Chapter 2 Adjusting Screens
29
●●HDMI (HD signal) input
Settings
Function
Enlarged
Displays an image in full screen. In some cases, a blank horizontal or vertical border
appears to equalize the vertical rate and the horizontal rate.
Dot by Dot
Displays images with the specified resolution.
Example: 720p
Enlarged
Dot by Dot
CS230
CX240
Procedure
.
1. Choose “Screen” from the Adjustment menu, and press
2. Choose “Screen Size” from “Screen”, and press
3. Select “Enlarged”, or “Dot by Dot” with
4. Press
.
or .
to exit.
Attention
• For CX240, an image cannot be displayed using the entire screen when the HDMI signal is input.
30
Chapter 2 Adjusting Screens
●●HDMI (SD signal) input
Settings
Function
Auto
The monitor automatically changes the screen size according to the aspect ratio sent from
the auto input signal.
4:3
Displays images in a 4:3 format screen.Black bars appear on both sides of the screen.
16:9 images are horizontally compressed.
Letter Box
Displays 16:9 letterboxed images in full screen.
Images other than the letterboxed ones are partly cut on top and bottom.
16:9
Displays the entire 16:9 image in full screen. Black bars appear on the top and bottom of
the screen.
4:3 images are horizontally expanded.
Example: 480i/480p (16:9)
Auto
Letter Box
4:3
16:9
CS230
CX240
Procedure
.
1. Choose “Screen” from the Adjustment menu, and press
.
2. Choose “Screen Size” from “Screen”, and press
3. Select “Auto”, “4:3”, “Letter Box”, or “16:9” with
4. Press
or .
to exit.
Attention
• For CX240, an image cannot be displayed using the entire screen when the HDMI signal is input.
2-7. Configuring Moving Image Performance
This function reduces visible afterimages that appear in fast moving images. If noise or afterimage is adversely
noticeable, set the “Overdrive” setting to “Off”.
Default setting: On
Procedure
1. Choose “Screen” from the Adjustment menu, and press
2. Choose “Overdrive” from “Screen”, and press
3. Select “On” or “Off” with
4. Press
.
.
or .
to exit.
Chapter 2 Adjusting Screens
31
2-8. Specifying Color Space
The color space of the input signal is specified. Set to other than “Auto” if this product cannot display correct color.
Settings
Function
Auto
Identifies the color space of the input signal automatically.
YUV 4:2:2
Converts the color space of the input signal to a YUV 4:2:2 format.
YUV 4:4:4
Converts the color space of the input signal to a YUV 4:4:4 format.
RGB
Converts the color space of the input signal to an RGV format.
Procedure
.
1. Choose “Screen” from the Adjustment menu, and press
2. Choose “Color Space” from “Screen”, and press
.
or .
3. Select “Auto”, “YUV 4:2:2”, “YUV 4:4:4”, or “RGB” with
4. Press
to exit.
Attention
• The setting is required when a DVI device is connected to the monitor (at the HDMI connector port) using the DVIHDMI conversion connector.
• Even if “Auto” is set, correct color might not be displayed.
Note
• The color space at the DVI input is converted to an RGB format.
2-9. Setting HDMI
●●Reducing Noise
The small noises that occur in dark images are reduced. Use this function to reduce noise and roughness in
images.
Procedure
.
1. Choose “Screen” from the Adjustment menu, and press
2. Choose “HDMI Settings” from “Screen”, and press
3. Choose “Noise Reduction”, and press
4. Select “On” or “Off” with
5. Press
.
or .
to exit.
Attention
• Using the Noise Reduction function may deteriorate fine images.
32
Chapter 2 Adjusting Screens
.
Chapter 3 Setting Monitor
3-1. Enabling/Disabling Mode Selection
Allows you to select the specified modes only.
Use this function when all the display modes are not available or when keeping the display mode unchanged.
Procedure
.
1. Choose “Tools” from the Adjustment menu, and press
2. Choose “Mode Preset” from “Tools”, and press
3. Use
or
to select the mode to change, and press
4. Select “On” or “Off” with
5. Press
.
.
or .
to exit.
Attention
• You cannot set all the modes disable. Set at least one mode to “On”.
3-2. Selecting the Language
This function allows you to select a language for the Adjustment menu and messages.
Selectable languages
English/German/French/Spanish/Italian/Swedish/Japanese/Simplified Chinese/Traditional Chinese
Procedure
1. Choose “Menu Settings” from the Adjustment menu, and press
2. Choose “Language” from “Menu Settings”, and press
3. Select a language with
4. Press
.
.
or .
to exit.
3-3. Setting Orientation
This function allows you to change the orientation of the Adjustment menu.
Procedure
1. Choose “Menu Settings” from the Adjustment menu, and press
2. Choose “Orientation” from “Menu Settings”, and press
3. Select “Landscape” or “Portrait” with
4. Press
.
.
or .
to exit.
5. When selecting “Portrait”, turn the monitor screen 90˚ in clockwise direction.
Attention
• Make sure that the cables are correctly connected.
• Make sure to turn the monitor screen after pulling up the screen to the uppermost position of the stand and setting the
screen tilted upward.
Note
• When using the monitor screen in a portrait position, a graphics board that supports portrait display is required. When
placing the monitor in a portrait position, the settings of your graphics board need to be changed. Refer to the User’s
Manual of the graphics board for details. Please refer to our web site (http://www.eizoglobal.com) as well.
Chapter 3 Setting Monitor
33
3-4. Changing Adjustment Menu Display Position
You can change the display position of the Adjustment menu.
Procedure
.
1. Choose “Menu Settings” from the Adjustment menu, and press
.
2. Choose “Menu Position” from “Menu Settings”, and press
3. Choose the position with
or .
to exit.
4. Press
3-5. Showing and Hiding the EIZO Logo
Procedure
1. Press
to turn off the monitor.
down, press
2. Holding
for at least two seconds to turn on the monitor.
The “Optional Settings” menu appears.
3. Choose “Logo” from “Optional Settings”, and press
4. Select “On” or “Off” with
or , and press
.
.
or .
5. Select “Finish” with
.
6. Press
3-6. Locking Operation Button
This function allows you to lock the settings status to prevent changing them.
Procedure
1. Press
to turn off the monitor.
down, press
2. Holding
for at least two seconds to turn on the monitor.
The “Optional Settings” menu appears.
3. Choose “Key Lock” from “Optional Settings”, and press
4. Choose “Off”, “Menu”, or “All” with
Settings
Off
(Default setting)
Buttons that can be locked
None (All buttons are enabled)
Menu
button
All
All buttons excluding
5. Select “Finish” with
6. Press
34
or , and press
.
Chapter 3 Setting Monitor
or .
.
.
3-7. Setting Signal Bandwidth
The range of frequency and detection sensitivity of the change in signal can be switched.
Attention
• This function cannot be used with HDMI input.
Procedure
1. Press
to turn off the monitor.
down, press
2. Holding
for at least two seconds to turn on the monitor.
The “Optional Settings” menu appears.
3. Choose “Signal Bandwidth” from “Optional Settings”, and press
4. Choose the input signal to set with
5. Select “Normal” or “Wide” with
.
or , and press
.
twice.
6. Press
7. Select “Finish” with
8. Press
or , and press
.
or .
.
3-8. Switching USB Port Automatically
This function allows the input signal to link the USB upstream port when one monitor is connected to two PCs.
This can switch the USB port automatically according to the switch of the input signal. To calibrate one monitor
using two PCs, the USB cables do not need to be connected again. USB devices such as the mouse and keyboard
connected to one monitor can be used with two PCs.
Attention
• To switch the USB port to be used, two USB cables are required. Prepare cables.
• If a storage device such as a USB memory is connected to the monitor, remove the device before changing the setting.
Otherwise, data may be lost or damaged.
• The key arrangement of the keyboard cannot be changed.
Note
• When the “Input Selection” function is set to “Auto”, the USB port automatically switches according to the switch of the
input signal.
• The USB downstream port can be operated using the currently monitored PC.
Procedure
.
1. Choose “Tools” from the Adjustment menu, and press
2. Choose “USB Selection” from “Tools”, and press
3. Choose the input signal to set with
4. Select “USB-1” or “USB-2” with
5. Press
or , and press
.
.
or .
to exit.
Chapter 3 Setting Monitor
35
3-9. Changing DUE (Digital Uniformity Equalizer)
Setting
The DUE setting can be changed.
Settings
Function
Brightness
Makes the brightness and color of the whole screen uniform without changing the
maximum brightness and contrast ratio. The brightness of a high gradation area is not
corrected. Select this setting to prioritize the levels of the brightness and contrast over the
uniformity in the high gradation area.
Uniformity (Default
setting)
Makes the brightness and color of the whole screen uniform. The brightness of a high
graduation area is also corrected so it is uniform. Select this setting to prioritize the
uniformity over the levels of the brightness and contrast in the high gradation area.
Attention
• To change the DUE setting, the adjusted monitor display must be readjusted. Perform the target adjustment again using
ColorNavigator or ColorNavigator Elements. Regarding ColorNavigator and ColorNavigator Elements, see “To use
ColorNavigator / ColorNavigator Elements” (page 10).
Procedure
1. Press
to turn off the monitor.
down, press
2. Holding
for at least two seconds to turn on the monitor.
The “Optional Settings” menu appears.
3. Choose “DUE Priority” from “Optional Settings”, and press
4. Select “Uniformity” or “Brightness” with
5. Select “Finish” with
6. Press
.
or , and press
.
or .
.
3-10. Reset to default
The setting values are reset to the default settings.
Attention
• After resetting, you cannot undo the operation.
Note
• Regarding the default setting, see “Main Default Settings (CS230, CX240)” (page 53).
●●To reset the color adjustments
This function only resets the color adjustment value for the currently selected mode to the default settings.
Procedure
.
1. Choose “Color” from the Adjustment menu, and press
2. Choose “Color Reset” from “Color”, and press
3. Select “Execute” with
4. Press
36
.
Chapter 3 Setting Monitor
or .
.
●●To reset all adjustments to the default settings
This function resets all adjustments to the default settings (except the “Optional Settings” menu and “USB
Selection”).
Procedure
1. Choose “Tools” from the Adjustment menu, and press
2. Choose “All Reset” from “Tools”, and press
3. Select “Execute” with
4. Press
.
.
or .
.
Chapter 3 Setting Monitor
37
Chapter 4 SelfCorrection
This product is equipped with a built-in correction sensor. The conditions that have been adjusted using ColorNavigator
and the measurement device, or ColorNavigator Elements can be maintained.
As the adjustment targets or interval times for SelfCorrection are set in advance using ColorNavigator or
ColorNavigator Elements, the built-in correction sensor automatically executes regular display correction.
Attention
• To execute SelfCorrection, it is necessary to set the correction details. Set the target value in advance using ColorNavigator
or ColorNavigator Elements. Regarding ColorNavigator and ColorNavigator Elements, see “To use ColorNavigator /
ColorNavigator Elements” (page 10).
Note
• SelfCorrection can also be executed when there are no computer signals being input.
4-1. Executing SelfCorrection
Procedure
1. Choose “SelfCorrection” from the Adjustment menu, and press
2. Choose “Execute” from “SelfCorrection”, and press
.
.
The built-in correction sensor is activated, and SelfCorrection is executed.
Attention
• After selecting “Execute”, aging may be executed before the built-in correction sensor is executed.
38
Chapter 4 SelfCorrection
Chapter 5 Power Saving Functions
5-1. Setting Power Save
This function allows you to set the monitor into the power saving mode according to the PC status. When the
monitor has shifted to the power saving mode, the images on the screen are not displayed.
Attention
• Turning off the main power switch or unplugging the power cord completely shuts off power supply to the monitor.
• Devices connected to the USB downstream port work when the monitor is in power saving mode or when the power button
of the monitor is Off (except when “USB Power Save” is set to “On” in “5-5. Setting USB Power Save” (page 41)). Therefore,
power consumption of the monitor varies with connected devices even in the power saving mode.
• Five seconds before the monitor enters the power saving mode, it displays a preliminary message.
Procedure
.
1. Choose “PowerManager” from the Adjustment menu, and press
.
2. Choose “Power Save” from “PowerManager”, and press
3. Select “On” or “Off” with
4. Press
or .
to exit.
Power Saving System
Analog Signal Input
This monitor complies with the VESA DPM standard.
PC
On
Power saving
mode
STAND-BY
SUSPENDED
Off
Monitor
Power Indicator
Operating mode
Blue
Power saving mode
Orange
Digital Signal Input
- DVI signal input
This monitor complies with the “DVI DMPM” standard.
- DisplayPort signal input
This monitor complies with the “DisplayPort Standard V1.1a”.
PC
Monitor
Power Indicator
On
Operating mode
Blue
Power saving mode
Power saving mode
Orange
HDMI Signal Input
The monitor enters the power saving mode after five seconds in connection with the PC setting.
PC
Monitor
Power Indicator
On
Operating mode
Blue
Power saving mode
Power saving mode
Orange
Exiting the power saving mode
If the monitor receives input, it automatically exits the power saving mode and returns to the normal display
mode.
Chapter 5 Power Saving Functions
39
5-2. Enabling/Disabling Automatic Brightness
Adjustment
The ambient light sensor on the front side of the monitor detects the environmental brightness to adjust the screen
brightness automatically and comfortably by using the Auto EcoView function.
Attention
• Be careful not to block the ambient light sensor on the lower side of the monitor when using the Auto EcoView function.
• Auto EcoView cannot be used when ColorNavigator and/or ColorNavigator Elements is used.
Procedure
.
1. Choose “PowerManager” from the Adjustment menu, and press
.
2. Choose “Auto EcoView” from “PowerManager”, and press
3. Select “On” or “Off” with
4. Press
or .
to exit.
Note
• For this reason, as “Brightness” in the Adjustment menu is changed, the auto adjustment range is also changed.
5-3. Checking the Power Saving Level
The EcoView menu allows you to check Power Reduction, CO2 Reduction, and Eco Performance Level. The more
indicators light up representing the Eco Performance Level, the higher the power saving level attained.
Procedure
.
1. Choose “PowerManager” from the Adjustment menu, and press
.
2. Choose “EcoView Index” from “PowerManager”, and press
The “EcoView Index” appears.
5-4. Adjusting the Brightness of Indicator
The brightness of the power indicator (blue) can be adjusted. (Default setting: 4)
Procedure
1. Choose “PowerManager” from the Adjustment menu, and press
2. Choose “Indicator” from “PowerManager”, and press
3. Select the indicator brightness “Off” or in the range from 1 to 7 with
4. Press
40
to exit.
Chapter 5 Power Saving Functions
.
.
or
as desired.
5-5. Setting USB Power Save
This function allows you to disable the USB connection according to the power saving mode of the monitor.
Attention
• When both the USB upstream port and the USB downstream port are connected to USB devices, the USB connection is not
disabled even when “USB Power Save” is set to “On”.
Procedure
1. Press
to turn off the monitor.
down, press
2. Holding
for at least two seconds to turn on the monitor.
The “Optional Settings” menu appears.
3. Choose “USB Power Save” from “Optional Settings”, and press
4. Select “On” or “Off” with
5. Select “Finish” with
or , and press
.
.
or .
.
6. Press
5-6. Setting DisplayPort Power Save
If the PC is connected to the DisplayPort connector, and when the power is turned on or off or when the monitor
recovers from power saving mode, window or icon positions may be shifted. If that occurs, set this function to
“Off”.
Procedure
1. Press
to turn off the monitor.
down, press
2. Holding
for at least two seconds to turn on the monitor.
The “Optional Settings” menu appears.
3. Choose “DP Power Save” from “Optional Settings”, and press
4. Select “On” or “Off” with
5. Select “Finish” with
6. Press
or , and press
.
.
or .
.
Chapter 5 Power Saving Functions
41
Chapter 6 Troubleshooting
If a problem still remains after applying the suggested remedies, contact your local EIZO representative.
6-1. No picture
Problem
1. No picture
• Power indicator does not light.
• Power indicator is lighting blue.
• Power indicator is lighting orange.
• Power indicator flashes orange and blue.
2. The message below appears.
•
•
•
•
Check whether the power cord is connected properly.
Turn the main power switch on.
Press .
Turn off the main power, and then turn it on again a few
minutes later.
• Increase “Brightness” and/or “Gain” in the Adjustment
menu (see “To perform advanced adjustments” (page 19)).
.
Switch the input signal with
Operate the mouse or keyboard.
Check whether the PC is turned on.
The DisplayPort or HDMI connection eventually cause a
problem. Please switch the monitor off and on to solve the
problem. Refer to the User’s Manual of the output device
for further details..
This message appears when the signal is not input correctly
even when the monitor functions properly.
•
•
•
•
• This message appears when no signal is
input.
Example:
• The message shown left may appear, because some PCs
do not output the signal soon after power-on.
• Check whether the PC is turned on.
• Check whether the signal cable is connected properly.
• Switch the input signal with
.
• The message shows that the input signal is out
of the specified frequency range. (Such signal
frequency is displayed in magenta.)
Example:
• Check whether the PC is configured to meet the resolution
and vertical scan frequency requirements of the monitor
(see “2-1. Compatible Resolutions” (page 15)).
• Reboot the PC.
• Select an appropriate setting using the graphics boards
utility. Refer to the User’s Manual of the graphics board
for details.
fD: Dot Clock (displayed only during the
digital signal input)
fH: Horizontal Scan Frequency
fV: Vertical scan frequency
42
Possible cause and remedy
Chapter 6 Troubleshooting
6-2. Imaging problems
Problem
Possible cause and remedy
1. The screen is too bright or too dark.
• Use “Brightness” in the Adjustment menu to adjust it. (The
LCD monitor backlight has a limited life span.) When the
screen becomes dark or begins to flicker, contact your
local EIZO representative.
2. Characters are blurred.
• Check whether the PC is configured to meet the resolution
and vertical scan frequency requirements of the monitor
(see “2-1. Compatible Resolutions” (page 15)).
• Use “Outline Enhancer” in the Adjustment menu to adjust
it (see “To enhance outline of image” (page 22)).
3. Afterimages appear.
• Afterimages are particular to LCD monitors. Avoid
displaying the same image for a long time.
• Use the screen saver or power saving function to avoid
displaying the same image for extended periods of time.
4. Green/red/blue/white dots or defective
dots remain on the screen.
• This is due to LCD panel characteristics and is not a
failure.
5. Interference patterns or pressure marks
remain on the screen.
• Leave the monitor with a white or black screen. The
symptom may disappear.
6. Noise appears on the screen.
• In the Adjustment menu, set “Overdrive” to “Off” (see “2-7.
Configuring Moving Image Performance” (page 31)).
• When entering the signals of HDCP, the normal images
may not be displayed immediately.
7. (DisplayPort input)
Display position of the windows changes.
• When the signal is switched, the position of the window
may be changed. In the Adjustment menu, set “DP Power
Save” to “Off” (see “5-6. Setting DisplayPort Power Save”
(page 41)).
8. Displays are abnormal.
• Use “Screen” - "Color Space" (for the HDMI input) under
the Adjustment menu to adjust it.
9. An image does not display on the entire
screen.
• The screen is set to a size other than “Full”. Change the
setting to “Full”.
• For CX240, 1080i and 1080p are the maximum resolutions
when the HDMI signal is input, so an image cannot be
displayed using the entire screen.
Chapter 6 Troubleshooting
43
6-3. Other problems
Problem
44
Possible cause and remedy
1. The adjustment menu does not appear.
• Check whether the operation lock function is active (see
“3-6. Locking Operation Button” (page 34)).
2. No mode menu is displayed.
• Check whether the operation lock function is active (see
“3-6. Locking Operation Button” (page 34)).
3. The monitor connected with the USB cable
is not detected. / USB devices connected
to the monitor does not work.
• Check whether the USB cable is connected correctly (see
“7-3. Making Use of USB (Universal Serial Bus)” (page 49)).
• Check the “Tools” – “USB Selection” settings under
the Setting menu (see “3-8. Switching USB Port
Automatically” (page 35)).
• Change the USB port to another one. If the PC or
peripheral devices works correctly by changing the USB
port, contact your local EIZO representative. (Refer to the
manual of the PC for details.)
• Reboot the PC.
• If the peripheral devices work correctly when the PC and
peripheral devices are connected directly, please contact
your local EIZO representative.
• Check whether the PC and OS are USB compliant. (For
USB compliance of the respective devices, consult their
manufacturers.)
• Check the PC’s BIOS setting for USB when using
Windows. (Refer to the manual of the PC for details.)
4. Audio is not output.
• This monitor does not support the HDMI/DisplayPort
audio signals.
Chapter 6 Troubleshooting
6-4. Built-in correction sensor and SelfCorrection
problems
Problem
Possible cause and remedy
1. The built-in correction sensor does not
come out/stays out.
• Turn off the main power, and then turn it on again a few
minutes later.
2. SelfCorrection cannot be executed.
• Check whether the ColorNavigator license is certified.
(See “To use ColorNavigator / ColorNavigator Elements”
(page 10).)
• Set the SelfCorrection target using ColorNavigator or
ColorNavigator Elements.
3. SelfCorrection failure
• Refer to the error code table. If an error code that does
not appear in the error code table is displayed, contact
your local EIZO representative.
Error Code Table
Error Code
Description
0014
• Execute SelfCorrection again.
• Adjust using ColorNavigator or ColorNavigator Elements.
0034
• The built-in correction sensor may not have come out during calibration, or light may
have entered the sensor during measurement.
• Turn off the main power, wait for a few minutes before turning the power back on, and
then execute SelfCorrection again.
0050
• Execute SelfCorrection again.
0061
• The built-in correction sensor may not have come out.
• Check whether there is any foreign object near the built-in correction sensor.
• Execute SelfCorrection again.
Chapter 6 Troubleshooting
45
Chapter 7 Reference
7-1. Attaching the Optional Arm
An optional arm (or an optional stand) can be attached by removing the stand section. Please refer to our web site
for the corresponding optional arm (or optional stand). http://www.eizoglobal.com
Attention
• When attaching an arm or stand, follow the instructions of their User’s Manual.
• When using another manufacturer’s arm or stand, confirm the following in advance and select one conforming to the VESA
standard.
- Clearance between the screw holes: 100 mm × 100 mm
- Thickness of plate: 2.6 mm
- Strong enough to support weight of the monitor unit (except the stand) and attachments such as cables.
• When using another manufacturer’s arm or stand, use the following screws to secure it.
- Screws fixing the stand to the monitor.
• When using an arm or stand, attach it to meet the following tilt angles of the monitor.
- Up 45˚, down 45˚
• Connect the cables after attaching an arm or stand.
• Do not move the removed stand up and down. Doing so may result in injury or device damage.
• The monitor and arm or stand are heavy. Dropping them may result in injury or equipment damage.
• When setting the monitor to the portrait style, turn the monitor screen 90˚ in clockwise direction.
Procedure
1. Lay the LCD monitor on a soft cloth spread over on a stable surface with the
panel surface facing down.
2. Remove the stand.
Prepare a screwdriver. Loosen the screws (four) securing the unit and the stand with the screwdriver.
3. Attach the arm or stand to the monitor.
Secure the monitor to the arm or stand using the screws fixing the stand to the monitor.
46
Chapter 7 Reference
7-2. Connecting Multiple External Devices
The product has multiple connections to external devices and allows you to switch to one of the connections for
display.
Connection examples
DVI- I connector
HDMI connector
Digital
(DVI)
Digital
(HDMI)
Signal cable
(supplied FD-C39)
HDMI cable
(Commercially
available product) *1
DVI connector
HDMI connector
To external device 1
To external device 2
DisplayPort
connector
Digital
(DisplayPort)
Signal cable
(PM200)*2
Mini DisplayPort
connector
To external device 3
*1 Use a product able to handle High Speed .
*2 CS230:option, CX240:supplied
Chapter 7 Reference
47
●●To switch among input signals
The input signal switches each time
is pressed.
When the signal is switched, the active input port name appears at the top right corner of the screen.
●●To set input signal selection “Input Selection”
Settings
Function
Auto
The monitor recognizes the connector through which signals are input.
When an external device enters the power saving mode, the monitor automatically displays
another signal.
Manual
The monitor displays the signal from the selected connector despite the signal input. Select
the input signal for display using the
operation button.
Procedure
.
1. Choose “Tools” from the Adjustment menu, and press
2. Choose “Input Selection” from “Tools”, and press
3. Select “Auto” or “Manual” with
4. Press
.
or .
to exit.
Note
• When “Auto” is selected for “Input Selection”, the monitor’s power saving function works only when all external
devices are in the power saving mode.
48
Chapter 7 Reference
7-3. Making Use of USB (Universal Serial Bus)
This monitor has a USB hub. Connected to a PC compatible with USB, this monitor functions as a USB hub
allowing connection to peripheral USB devices.
●●System Requirement
• A PC (including devices with a USB host function) and OS in conformance with USB Specification Revision
2.0
• USB cable
Attention
• This monitor may not work depending on PC, OS or peripheral devices. For USB compatibility of peripheral devices,
contact their manufacturers.
• Devices connected to the USB upstream port and USB downstream port work when the monitor is in power saving
mode or when the power button of the monitor is Off. Therefore, power consumption of the monitor varies with
connected devices even in the power saving mode.
• When the main power of the monitor is Off, device connected to the USB downstream port does not operate.
●●Procedure
1. Connect the signal cable between a PC and the monitor, and turn on the PC.
2. Using the USB cable, connect the computer’s downstream port and the monitor’s upstream port 1.
3. Connect the peripheral USB device to the USB downstream port of the monitor.
Note
• By default, USB upstream port 1 is enabled. To connect two PCs, see “3-8. Switching USB Port Automatically” (page 35).
USB
upstream
port
USB
downstream
port
Chapter 7 Reference
49
7-4. Showing Monitor Information
●●Displaying signal information “Signal Info”
This function displays the information about the current input signals displayed.
Procedure
.
1. Choose “Tools” from the Adjustment menu, and press
2. Choose “Signal Info” from “Tools”, and press
.
The “Signal Info” appears.
(Example)
●●Displaying Monitor Information “Monitor Info”
This function displays the information about the monitor.
Procedure
.
1. Choose “Tools” from the Adjustment menu, and press
2. Choose “Monitor Info” from “Tools”, and press
.
The “Monitor Info” appears.
This function displays the model name, serial number, firmware version, usage time, and ColorNavigator license
status.
Attention
• The usage time is not always “0” when you purchase the monitor due to factory inspection.
• If “ColorNavigator License” in the monitor information screen is “Not Registered”, the ColorNavigator license must be
purchased and registered to the monitor. For the purchase of the license, contact your local EIZO representative.
50
Chapter 7 Reference
7-5. Specifications
●●CS230
LCD Panel
Size
23.0 inch (580 mm)
Type
Color TFT, IPS, LED backlight
Surface treatment
Hard Coating
Surface hardness
3H
Viewing angles
Horizontal 178˚, vertical 178˚ (CR≥10)
Dot pitch
0.265 mm
Response time
Black-white-black:
Approx. 15.2 ms
Gray-to-gray:
Approx. 10.5 ms
Horizontal scan Analog
frequency
Digital
26 kHz - 68 kHz
DVI /
26 kHz - 68 kHz
DisplayPort
HDMI
Vertical scan
frequency
Analog
Digital
15 kHz - 68 kHz
47.5 Hz - 61 Hz (non-interlace)
DVI /
23.75 Hz - 63 Hz (non-interlace)
DisplayPort (VGA TEXT: 69 - 71 Hz)
HDMI
23.75 Hz - 61 Hz
Frame Synchronous mode
23.75 Hz - 30.5 Hz, 47.5 Hz - 61 Hz
Resolution
1920 dots × 1080 lines
Max. dot clock
149.0 MHz
Max. display color
Approx. 1073.74 million colors (for DisplayPort 10 bit)
Display area (H × V)
509.2 mm (20.0 inch) × 286.4 mm (11.3 inch)
Power supply
100 Vac - 120 Vac ±10%, 50/60 Hz 0.6A
200 Vac - 240 Vac ±10%, 50/60 Hz 0.4A
Power
consumption
Screen display On
54 W or less
Power saving mode
0.5 W or less (when only the DVI signal connector is connected,
analog signal input, and no USB device is connected)
Power Off
0.5 W or less (when no USB device is connected)
Main power Off
Input signal connectors
0W
DVI-I connector (Applicable to HDCP)
DisplayPort connector (Standard V1.1a, applicable to HDCP)
HDMI connector (Applicable to TypeA, HDCP)
Analog input signal (Sync)
Separate, TTL, positive / negative
Analog signal transmission system
Analog, positive (0.7 Vp-p / 75 Ω)
Digital signal (DVI/HDMI) transmission
system
TMDS (Single Link)
Plug & Play
Digital (DVI-I): VESA DDC 2B / EDID structure 1.3
Digital (DisplayPort) : VESA DisplayPort / EDID structure 1.4
Main unit
544 mm (21.4 inch) × 372.5mm – 526.5 mm (14.7 inch - 20.7 inch) ×
Dimensions
245.5 mm (9.7 inch)
(width) × (height)
× (depth)
Main unit (without stand) 544 mm (21.4 inch) × 353 mm (13.9 inch) × 75 mm (3 inch)
Mass
Main unit
Approx. 7.9 kg (17.4 lbs.)
Main unit (without stand) Approx. 5.3 kg (11.7 lbs.)
Movable range
Tilt:
Up 30˚, down 0˚
Swivel:
344˚
Adjustable height:
195 mm (154 mm for tilt of 0˚)
Rotation:
90˚ (clockwise)
Chapter 7 Reference
51
Environmental
conditions
USB
●●CX240
LCD Panel
Temperature
Operating:
Storage/Transportation:
-20˚C to 60˚C (-4˚F to 140˚F)
Humidity
Operating:
20% to 80% R.H. (no condensation)
Storage/Transportation:
10% to 90% R.H. (no condensation)
Air pressure
Operating:
700 hPa to 1060 hPa
Storage/Transportation:
200 hPa to 1060 hPa
Standard
USB Specification Revision 2.0
Port
Upstream port × 2, Downstream port × 2
Communication Speed
480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low)
Supply current
Downstream:
Size
24.1 inch (610 mm)
Type
Color TFT, IPS, LED backlight
Surface treatment
Hard Coating
Surface hardness
3H
Viewing angles
Horizontal 178˚, vertical 178˚ (CR≥10)
Dot pitch
0.270 mm
Response time
Black-white-black:
Approx. 12 ms
Gray-to-gray:
Approx. 7.7 ms
Horizontal scan Analog
frequency
Digital
26 kHz - 78 kHz
Analog
Digital
Max. 500mA/1 port
DVI /
26 kHz - 78 kHz
DisplayPort
HDMI
Vertical scan
frequency
0˚C to 35˚C (32˚F to 95˚F)
15 kHz - 68 kHz
47.5 Hz - 61 Hz (non-interlace)
DVI /
23.75 Hz - 63 Hz (non-interlace)
DisplayPort (VGA TEXT: 69 Hz - 71 Hz)
HDMI
Frame Synchronous mode
23.75 Hz - 61 Hz
23.75 Hz - 30.5 Hz, 47.5 Hz - 61 Hz
Resolution
1920 dots × 1200 lines
Max. dot clock
164.5 MHz
Max. display color
Approx. 1073.74 million colors (for DisplayPort 10 bit)
Display area (H × V)
518.4 mm (20.4 inch) × 324.0 mm (12.8 inch)
Power supply
100Vac - 120 Vac ±10%, 50/60 Hz 1.0A
200Vac - 240 Vac ±10%, 50/60 Hz 0.6A
Power
consumption
Screen display On
98 W or less
Power saving mode
0.5 W or less (when only the DVI signal connector is connected,
analog signal input, and no USB device is connected)
Power Off
0.5 W or less (when no USB device is connected)
Main power Off
Input signal connectors
0W
DVI-I connector (Applicable to HDCP)
DisplayPort connector (Standard V1.1a, applicable to HDCP)
HDMI connector (Applicable to TypeA, HDCP)
Analog input signal (Sync)
Separate, TTL, positive / negative
Analog signal transmission system
Analog, positive (0.7 Vp-p / 75 Ω)
Digital signal (DVI/HDMI) transmission
system
TMDS (Single Link)
Plug & Play
Digital (DVI-I): VESA DDC 2B / EDID structure 1.3
Digital (DisplayPort) : VESA DisplayPort / EDID structure 1.4
Main unit
575 mm (22.6 inch) × 417 mm – 545 mm (16.4 inch - 21.5 inch) × 245.5
Dimensions
mm (9.7 inch)
(width) × (height)
× (depth)
Main unit (without stand) 575 mm (22.6 inch) × 398 mm (15.7 inch) × 75 mm (3 inch)
52
Chapter 7 Reference
Mass
Main unit
Approx. 9.7 kg (21.4 lbs.)
Main unit (without stand) Approx. 7.0 kg (15.4 lbs.)
Movable range
Environmental
conditions
Temperature
Humidity
Air pressure
USB
Tilt:
Up 30˚, down 0˚
Swivel:
344˚
Adjustable height:
195 mm (128 mm for tilt of 0˚)
Rotation:
90˚ (clockwise)
Operating:
0˚C to 35˚C (32˚F to 95˚F)
Storage/Transportation:
-20˚C to 60˚C (-4˚F to 140˚F)
Operating:
20% to 80% R.H. (no condensation)
Storage/Transportation:
10% to 90% R.H. (no condensation)
Operating:
700 hPa to 1060 hPa
Storage/Transportation:
200 hPa to 1060 hPa
Standard
USB Specification Revision 2.0
Port
Upstream port × 2, Downstream port × 2
Communication Speed
480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low)
Supply current
Downstream:
Max. 500mA/1 port
Main Default Settings (CS230, CX240)
Color Mode
User1
Outline Enhancer
0
Screen Size
Full (DVI, DisplayPort)
Enlarged (HDMI, HD)
Auto (HDMI, SD)
Overdrive
On
Power Save
On
Auto EcoView
On
Language
English
Menu Position
Center
Input Selection
Manual
USB Power Save
Off
DP Power Save
On
DUE Priority
Uniformity
Chapter 7 Reference
53
Outside Dimensions
CS230
Unit: mm (inch)
344°
SWIVEL
75 (2.95)
544 (21.4)
511.8 (20.1)
100 (3.9)
100 (3.9)
TILT 3
0°
372.5〜526.5 (14.7)
288.8 (11.4)
353 (13.9)
38 (1.50)
15 (0.59)
7.5 (0.30)
33.7 (1.33)
209.5 (8.2)
245.5 (9.7)
CX240
Unit: mm (inch)
38 (1.50)
75 (2.95)
516.2 (20.3)
344°
SWIVEL
273.5 (10.8)
27.3 (1.07)
TILT30
°~
Chapter 7 Reference
42 (1.65)
125 (4.9)
9 (0.35)
7.5 (0.30)
378.5 (14.9)
320 (12.6)
360.5 (14.2)
14.5 (0.57)
147.3 (5.8)
573.5 (22.6)
355 (14.0)
204.3 (8)
398 (15.7)
417~ 545 (16.4~21.5)
44.7 (1.76)
67.5 (2.66)
594.5~ 642.5 (21.6~25.3)
°
90
OT
PIV
209 (8.2)
54
237.5 (9.4)
157.7 (6.2) 100 (3.9) 140.3 (5.5)
575 (22.6)
520.4 (20.5)
27.3 (1.07)
27.3 (1.07)
209 (8.2)
245.5 (9.7)
63 (2.48)
308 (12.1)
100 (3.9)
237.5 (9.4)
7-6. Preset Timing
The following table shows factory preset analog signal timing.
Attention
• Display position may be deviated depending on the PC connected, which may require screen adjustment using Adjustment
menu.
• If a signal other than those listed in the table is input, adjust the screen using the Adjustment menu.However, screen display
may still be incorrect even after the adjustment.
• When interlace signals are used, the screen cannot be displayed correctly even after screen adjustment using the Adjustment
menu.
CS230
Resolution
Applicable
Signals
640 × 480
720 × 400
800 × 600
1024 × 768
1280 × 960
1280 × 1024
1680 × 1050
1680 × 1050
1920 × 1080
1920 × 1080
VGA
VGA TEXT
VESA
VESA
VESA
VESA
VESA CVT
VESA CVT RB
VESA CVT RB
CEA-861
Frequency
Polarity
Dot Clock:
MHz
Horizontal:
kHz
Vertical: Hz
Horizontal
Vertical
25.18
28.32
40.00
65.00
108.00
108.00
146.25
119.00
138.50
148.50
31.47
31.47
37.88
48.36
60.00
63.98
65.29
64.67
66.59
67.50
59.94
70.09
60.32
60.00
60.00
60.02
59.95
59.88
59.93
60.00
Negative
Negative
Positive
Negative
Positive
Positive
Negative
Positive
Negative
Positive
Negative
Positive
Positive
Negative
Positive
Positive
Positive
Negative
Positive
Positive
CX240
Resolution
Applicable
Signals
640 × 480
720 × 400
800 × 600
1024 × 768
1280 × 960
1280 × 1024
1600 × 1200
1680 × 1050
1680 × 1050
1920 × 1080
1920 × 1200
VGA
VGA TEXT
VESA
VESA
VESA
VESA
VESA
VESA CVT
VESA CVT RB
VESA CVT RB
VESA CVT RB
Frequency
Polarity
Dot Clock:
MHz
Horizontal:
kHz
Vertical: Hz
Horizontal
Vertical
25.18
28.32
40.00
65.00
108.00
108.00
162.00
146.25
119.00
138.50
154.00
31.47
31.47
37.88
48.36
60.00
63.98
75.00
65.29
64.67
66.59
74.04
59.94
70.09
60.32
60.00
60.00
60.02
60.00
59.95
59.88
59.93
59.95
Negative
Negative
Positive
Negative
Positive
Positive
Positive
Negative
Positive
Negative
Positive
Negative
Positive
Positive
Negative
Positive
Positive
Positive
Positive
Negative
Positive
Negative
Chapter 7 Reference
55
7-7. Glossary
Adobe®RGB
This is a definition of the practical RGB color space proposed by Adobe Systems in 1998. The color
reproduction range (color gamut) is broader than sRGB, and is highly adaptable to such fields as printing etc.
Clock
The analog signal input monitor needs to reproduce a clock of the same frequency as the dot clock of the
graphics system in use, when the analog signal is converted to a digital signal for image display. This is
called clock adjustment. If the clock pulse is not set correctly, some vertical bars appear on the screen.
Color Space
YUV and RGB, etc. are available. YUV expresses the color by using the luminance (Y), the color difference
of Blue (U), and the color difference of Red (V). RGB does this by using the gradation of the 3 colors, Red
(R), Green (G), and Blue (B).
DisplayPort
This is a next-generation digital AV interface used to connect PCs and audio-visual devices to the monitor.
Both the video and sound signals can be transferred using one cable.
DVI (Digital Visual Interface)
DVI is a digital interface standard. DVI allows direct transmission of the PC’s digital data without loss.
This adopts the TMDS transmission system and DVI connectors. There are two types of DVI connectors.
One is a DVI-D connector for digital signal input only. The other is a DVI-I connector for both digital and
analog signal inputs.
DVI DMPM (DVI Digital Monitor Power Management)
DVI DMPM is a digital interface power saving function. The “Monitor ON (operating mode)” and “Active
Off (power saving mode)” are indispensable for DVI DMPM as the monitor’s power mode.
Gain
This is used to adjust each color parameter for red, green and blue. An LCD monitor displays the color by
the light passing through the panel color filter. Red, green and blue are the three primary colors. All the
colors on the screen are displayed by combining these three colors. The color tone can be changed by
adjusting the light intensity (volume) passing through each color’s filter.
Gamma
Generally, the relationship that the light intensity values of a monitor change nonlinearly to the input signal
level is called “Gamma Characteristic”. On the monitor, low gamma values display the whitish images and
high gamma values display the high contrast images.
56
Chapter 7 Reference
HDCP (High-bandwidth Digital Content Protection)
Digital signal coding system developed to copy-protect the digital contents, such as video, music, etc.
This helps to transmit the digital contents safely by coding the digital contents sent via the DVI or HDMI
connector on the output side and decoding them on the input side.
Any digital contents cannot be reproduced if both of the equipments on the output and input sides are not
applicable to HDCP system.
HDMI (High-Definition Multimedia Interface)
HDMI is a digital interface standard, developed for consumer electrical appliance or AV device. This
standard is issued on the basis of the DVI standard which is one of an interface specification for the
connection between a PC and a monitor.The projected image, sound and control signal without compressed
enable to be transmitted with one cable.
Overdrive
This technology enhances response speed by increasing the potential difference at the time of motion of
liquid-crystal pixels, and it is used for liquid-crystal TV sets and others in general. It provides clear-cut
three-dimensional display with little afterimage, by improving response speed of the intermediate graduation
range that frequently appears in moving images.
Resolution
The LCD panel consists of numerous pixels of specified size, which are illuminated to form images. This
monitor consists of horizontal 1920 pixels and 1080(CS230) / 1200(CX240) vertical pixels. At a resolution of
1920 × 1080(CS230) / 1920 × 1200(CX240), all pixels are illuminated as a full screen (1:1).
sRGB (Standard RGB)
International standard for color reproduction and color space among peripheral devices (such as monitors,
printers, digital cameras, scanners). As a form of simple color matching for the Internet, colors can be
displayed using tones close to those of the transmission and reception devices.
Temperature
Color temperature is a method to measure the white color tone, generally indicated in degrees Kelvin. The
screen becomes reddish at a low temperature, and bluish at a high temperature, like the flame temperature.
5000 K: Slightly reddish white
6500 K: White referred to as daylight-balanced color
9300 K: Slightly bluish white
TMDS (Transition Minimized Differential Signaling)
A signal transmission system for digital interface.
Chapter 7 Reference
57
Appendix
Trademark
The DisplayPort Compliance Logo and VESA are registered trademark of the Video Electronics Standards
Association.
Windows, Windows Vista, Windows Media, SQL Server, and Xbox 360 are registered trademarks of Microsoft
Corporation in the United States and other countries.
Apple, Mac, Macintosh, iMac, eMac, Mac OS, MacBook, PowerBook, ColorSync, QuickTime, and iBook are
registered trademarks of Apple Inc.
Acrobat, Adobe, Adobe AIR, and Photoshop are registered trademarks of Adobe Systems Incorporated in the
United States and other countries.
PowerPC is a registered trademark of International Business Machines Corporation.
Pentium is a registered trademark of Intel Corporation in the United States and other countries.
AMD Athlon and AMD Opteron are trademarks of Advanced Micro Devices, Inc.
GRACoL and IDEAlliance are registered trademarks of International Digital Enterprise Alliance.
ColorVision, ColorVision Spyder2 are registered trademarks of DataColor Holding AG.
Spyder3 is a trademark of DataColor Holding AG.
Eye-One, ColorMunki, and X-Rite are registered trademarks or trademarks of X-Rite Incorporated.
TouchWare is a trademark of 3M Touch Systems, Inc.
NextWindow is a registered trademark of NextWindow Ltd.
RealPlayer is a registered trademark of RealNetworks, Inc.
NEC is a registered trademark of NEC Corporation. PC-9801 and PC-9821 are trademarks of NEC Corporation.
PlayStation is a registered trademark of Sony Computer Entertainment Inc.
PSP and PS3 are trademarks of Sony Computer Entertainment Inc.
ENERGY STAR is a registered trademark of the United States Environmental Protection Agency in the United
States and other countries.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing, LLC in the United States and other countries.
EIZO, the EIZO Logo, ColorEdge, DuraVision, FlexScan, FORIS, RadiForce, RadiCS, RadiNET, Raptor, and
ScreenManager are registered trademarks of EIZO Corporation in Japan and other countries.
ColorNavigator, EIZO EasyPIX, EcoView NET, EIZO ScreenSlicer, i • Sound, Screen Administrator, and UniColor
Pro are trademarks of EIZO Corporation.
All other company and product names are trademarks or registered trademarks of their respective owners.
License
A round gothic bold bit map font designed by Ricoh is used for the characters displayed on this product.
58
Appendix
FCC Declaration of Conformity
For U.S.A. , Canada, etc. (rated 100-120 Vac) Only
FCC Declaration of Conformity
We, the Responsible Party
EIZOInc.
5710WarlandDrive,Cypress,CA90630
Phone:(562)431-5011
declare that the product
Tradename:EIZO
Model:ColorEdgeCS230/CX240
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuant
toPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainst
harmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,uses,andcanradiateradio
frequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmful
interferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurin
aparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,
whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotrytocorrectthe
interferencebyoneormoreofthefollowingmeasures.
* Reorientorrelocatethereceivingantenna.
* Increasetheseparationbetweentheequipmentandreceiver.
* Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.
* Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
Changesormodificationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidthe
user’sauthoritytooperatetheequipment.
Note
UsetheattachedspecifiedcablebeloworEIZOsignalcablewiththismonitorsoastokeepinterference
withinthelimitsofaClassBdigitaldevice.
- ACCord
- ShieldedSignalCable(Enclosed)
Canadian Notice
ThisClassBdigitalapparatuscomplieswithCanadianICES-003.
CetappareilnumériquedeleclasseBestcomformeàlanormeNMB-003duCanada.
Appendix
59
LIMITED WARRANTY
LIMITED WARRANTY
EIZOCorporation(hereinafterreferredtoas“EIZO”)anddistributorsauthorizedbyEIZO(hereinafterreferredtoasthe
“Distributors”)warrant,subjecttoandinaccordancewiththetermsofthislimitedwarranty(hereinafterreferredtoasthe
“Warranty”),totheoriginalpurchaser(hereinafterreferredtoasthe“Original Purchaser”)whopurchasedtheproduct
specifiedinthisdocument(hereinafterreferredtoasthe“Product”)fromEIZOorDistributors,thatEIZOandDistributors
shall,attheirsolediscretion,eitherrepairorreplacetheProductatnochargeiftheOriginalPurchaserbecomesaware
withintheWarrantyPeriod(definedbelow)thattheProductmalfunctionsorisdamagedinthecourseofnormaluseof
theProductinaccordancewiththedescriptionintheinstructionmanualattachedtotheProduct(hereinafterreferredto
asthe“User’s Manual”).
The period of this Warranty is limited to (i) five (5) years from the date of purchase of the Product; or, limited to the
expiration of (ii) 30,000 hours of its use of the Product(hereinafterreferredtoasthe“Warranty Period”).EIZOand
DistributorsshallbearnoliabilityorobligationwithregardtotheProductinrelationtotheOriginalPurchaseroranythird
partiesotherthanasprovidedunderthisWarranty.
EIZOandDistributorswillceasetoholdorstoreanyparts(excludingdesignparts)oftheProductuponexpirationof
seven(7)yearsaftertheproductionofsuchpartsisdiscontinued.Inrepairingthemonitor,EIZOandDistributorswilluse
renewalpartswhichcomplywithourQCstandards.Iftheunitcannotberepairedduetoitsconditionorthestockoutof
arelevantpart,EIZOandDistributorsmayofferthereplacementbyaproductwithequivalentperformanceinsteadof
repairingit.
TheWarrantyisvalidonlyinthecountriesorterritorieswheretheDistributorsarelocated.TheWarrantydoesnotrestrict
anylegalrightsoftheOriginalPurchaser.
NotwithstandinganyotherprovisionofthisWarranty,EIZOandDistributorsshallhavenoobligationunderthisWarranty
whatsoeverinanyofthecasesassetforthbelow:
(a) AnydefectoftheProductcausedbyfreightdamage,modification,alteration,abuse,misuse,accident,incorrect
installation,disaster,faultymaintenanceand/orimproperrepairbythirdpartyotherthanEIZOandDistributors;
(b) AnyincompatibilityoftheProductduetopossibletechnicalinnovationsand/orregulations;
(c) Anydeteriorationofthesensor;
(d) AnydeteriorationofdisplayperformancecausedbythedeteriorationofexpendablepartssuchastheLCDpanel
and/orbacklight,etc.(e.g.changesinbrightness,changesinbrightnessuniformity,changesincolor,changesin
coloruniformity,defectsinpixelsincludingburntpixels,etc.);
(e) AnydefectoftheProductcausedbyexternalequipment;
(f) AnydefectoftheProductonwhichtheoriginalserialnumberhasbeenalteredorremoved;
(g) Anynormaldeteriorationoftheproduct,particularlythatofconsumables,accessories,and/orattachments(e.g.
buttons,rotatingparts,cables,User’sManual,etc.);and
(h) Anydeformation,discoloration,and/orwarpoftheexterioroftheproductincludingthatofthesurfaceoftheLCD
panel.
To obtain service under the Warranty, the Original Purchaser must deliver the Product, freight prepaid, in its original
packageorotheradequatepackageaffordinganequaldegreeofprotection,assumingtheriskofdamageand/orloss
intransit,tothelocalDistributor.TheOriginalPurchasermustpresentproofofpurchaseoftheProductandthedateof
suchpurchasewhenrequestingservicesundertheWarranty.
TheWarrantyPeriodforanyreplacedand/orrepairedproductunderthisWarrantyshallexpireattheendoftheoriginal
WarrantyPeriod.
EIZO OR DISTRIBUTORSARE NOT RESPONSIBLE FORANY DAMAGE TO, OR LOSS OF, DATA OR OTHER
INFORMATIONSTOREDINANYMEDIAORANYPARTOFANYPRODUCTRETURNEDTOEIZOORDISTRIBUTORS
FORREPAIR.
EIZOAND DISTRIBUTORS MAKE NO FURTHER WARRANTIES, EXPRESSED OR IMPLIED, WITH RESPECTTO
THE PRODUCTAND ITS QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FORANY PARTICULAR
USE. IN NO EVENT SHALL EIZO OR DISTRIBUTORS BE LIABLE FORANY INCIDENTAL, INDIRECT, SPECIAL,
CONSEQUENTIAL OR OTHER DAMAGE WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR
LOSSOFPROFIT,BUSINESSINTERRUPTION,LOSSOFBUSINESSINFORMATION,ORANYOTHERPECUNIARY
LOSS)ARISINGOUTOFTHEUSEORINABILITYTOUSETHEPRODUCTORINANYCONNECTIONWITHTHE
PRODUCT,WHETHERBASEDONCONTRACT,TORT,NEGLIGENCE,STRICTLIABILITYOROTHERWISE,EVEN
IFEIZOORDISTRIBUTORSHAVEBEENADVISEDOFTHEPOSSIBILITYOFSUCHDAMAGES.THISEXCLUSION
ALSO INCLUDESANY LIABILITY WHICH MAYARISE OUT OFTHIRD PARTY CLAIMSAGAINSTTHE ORIGINAL
PURCHASER. THE ESSENCE OF THIS PROVISION IS TO LIMIT THE POTENTIAL LIABILITY OF EIZOAND
DISTRIBUTORSARISINGOUTOFTHISLIMITEDWARRANTYAND/ORSALES.
60
Appendix
BEGRENZTE GARANTIE
EIZO Corporation (im Weiteren als „EIZO“ bezeichnet) und die Vertragsimporteure von EIZO (im Weiteren als
„Vertrieb(e)“bezeichnet)garantierendemursprünglichenKäufer(imWeiterenals„Erstkäufer“bezeichnet),derdasin
diesemDokumentvorgegebeneProdukt(imWeiterenals„Produkt“bezeichnet)vonEIZOodereinemVertrieberworben
hat,gemäßdenBedingungendieserbeschränktenGarantie(imWeiterenals„Garantie“bezeichnet),dassEIZOund
derVertriebnacheigenemErmessendasProduktentwederkostenlosreparierenoderaustauschen,fallsderErstkäufer
innerhalb der Garantiefrist (weiter unten festgelegt) eine Fehlfunktion bzw. Beschädigung des Produkts feststellt,
die während des normalen Gebrauchs des Produkts gemäß denAnweisungen des zum Lieferumfang des Produkts
gehörendenBenutzerhandbuchs(imWeiterenals„Benutzerhandbuch“bezeichnet)aufgetretenist.
Die Dauer der Garantieleistung beträgt (i) fünf (5) Jahre ab dem Erstverkaufsdatum des Produkts oder (ii) 30.000
BetriebsstundendesProdukts(imWeiterenals„Garantiefrist“bezeichnet).EIZOunddieVertriebeübernehmenüber
denRahmendieserGarantiehinaushinsichtlichdesProduktskeinerleiHaftungoderVerpflichtungdemErstkäuferoder
Drittengegenüber.
NachAblaufvonsieben(7)JahrennachEndederProduktionsolcherTeilewerdenEIZOundVertriebshändlerkeine
Teile(mitAusnahmevonKonstruktionsteilen)mehrvorhaltenundlagern.EIZOundseineVertriebspartnerverpflichten
sich,beieineretwaigenReparaturdesMonitorsausschließlichProduktegemäßdenEIZO-Qualitätssicherungsstandards
zuverwenden.WenndasGerätaufgrundseinesZustandsodereinesFehlbestandsbeieinementsprechendenTeilnicht
repariert werden kann, können EIZO und Vertriebshändler statt der Reparatur des Geräts denAustausch gegen ein
ProduktmitgleichwertigerLeistunganbieten.
Diese Garantie gilt nur in Ländern oder Gebieten, in denen sich Vertriebe befinden. Die gesetzlichen
GewährleistungsrechtedesErstkäufersgegenüberdemVerkäuferwerdendurchdieseGarantienichtberührt.
EIZOunddieVertriebebesitzenimRahmendieserGarantiekeinerleiVerpflichtungindenfolgendenFällen:
(a) Produktdefekte, die auf Frachtschäden, Modifikation, Nachgestaltung, Missbrauch, Fehlbedienung, Unfälle,
unsachgemäßeInstallation,Naturkatastrophen,fehlerhafteWartungund/oderunsachgemäßeReparaturdurcheine
andereParteialsEIZOunddieVertriebezurückzuführensind.
(b) Eine Inkompatibilität des Produkts aufgrund von technischen Neuerungen und/oder neuen Bestimmungen, die
nachdemKaufinKrafttreten.
(c) JeglicheVerschlechterungdesSensors.
(d) Jegliche Verschlechterung der Bildschirmleistung, die durch Verschleißteile wie das LCD-Panel und/oder die
Hintergrundbeleuchtungusw.hervorgerufenwerden(z.B.VeränderungenvonHelligkeitoderHelligkeitsverteilung,
VeränderungenvonFarbeoderFarbverteilung,PixeldefekteeinschließlichvondurchgebranntenPixelnusw.).
(e) Produktdefekte,diedurchexterneGeräteverursachtwerden.
(f) JeglicherDefekteinesProdukts,dessenursprünglicheSeriennummergeändertoderentferntwurde.
(g) NormaleAbnutzung des Produkts, insbesondere von Verbrauchsteilen, Zubehörteilen und/oder Beilagen (z.B.
Tasten,drehbareTeile,Kabel,Benutzerhandbuchusw.);sowie
(h) Verformungen,Verfärbungenund/oderVerziehungenamProduktäußeren,einschließlichderOberflächedesLCD-Panels.
Bei Inanspruchnahme der Garantieleistung ist der Erstkäufer verpflichtet, das Produkt auf eigene Kosten und
in der Originalverpackung bzw. einer anderen geeigneten Verpackung, die einen gleichwertigen Schutz gegen
Transportschädenbietet,andenörtlichenVertriebzuübersenden,wobeiderErstkäuferdasTransportrisikogegenüber
Schädenund/oderVerlustträgt.ZumZeitpunktderInanspruchnahmederGarantieleistungmussderErstkäufereinen
Verkaufsbelegvorweisen,aufdemdasKaufdatumangegebenist.
DieGarantiefristfüreinimRahmendieserGarantieausgetauschtesund/oderrepariertesProdukterlischtnachAblauf
derursprünglichenGarantiefrist.
EIZOODERDIEEIZO-VERTRAGSIMPORTEUREHAFTENNICHTFÜRZERSTÖRTEDATENBESTÄNDEODERDIE
KOSTEN DER WIEDERBESCHAFFUNG DIESER DATENBESTÄNDEAUF JEGLICHEN DATENTRÄGERN ODER
TEILENDESPRODUKTS,DIEIMRAHMENDERGARANTIEBEIEIZOODERDENEIZO-VERTRAGSIMPORTEUREN
ZURREPARATUREINGEREICHTWURDEN.
EIZO UND DIE EIZO-VERTRAGSIMPORTEURE GEBEN WEDER EXPLIZITE NOCH IMPLIZITE GARANTIEN
IN BEZUGAUF DIESES PRODUKT UND SEINE QUALITÄT, LEISTUNG, VERKÄUFLICHKEIT ODER EIGNUNG
FÜR EINEN BESTIMMTEN ZWECK.AUF KEINEN FALL SIND EIZO ODER DIE EIZO-VERTRAGSIMPORTEURE
VERANTWORTLICH FÜR JEGLICHE ZUFÄLLIGE, INDIREKTE, SPEZIELLE, FOLGE- ODERANDERE SCHÄDEN
JEGLICHERART (EINSCHLIESSLICH OHNE JEDE BEGRENZUNG SCHÄDEN BEZÜGLICH PROFITVERLUST,
GESCHÄFTSUNTERBRECHUNG, VERLUST VON GESCHÄFTSINFORMATION ODER JEGLICHEANDEREN
FINANZIELLEN EINBUSSEN), DIE DURCH DIE VERWENDUNG DES PRODUKTES ODER DIE UNFÄHIGKEIT
ZUR VERWENDUNG DES PRODUKTES ODER IN JEGLICHER BEZIEHUNG MIT DEM PRODUKT, SEI ES
BASIERENDAUFVERTRAG,SCHADENSERSATZ,NACHLAESSIGKEIT,STRIKTEHAFTPFLICHTODERANDEREN
FORDERUNGEN ENTSTEHEN,AUCH WENN EIZO UND DIE EIZO-VERTRAGSIMPORTEURE IM VORAUS ÜBER
DIEMÖGLICHKEITSOLCHERSCHÄDENINFORMIERTWURDEN.DIESERAUSSCHLUSSENTHÄLTAUCHJEDE
HAFTPFLICHT, DIEAUS FORDERUNGEN DRITTER GEGEN DEN ERSTKÄUFER ENTSTEHEN KANN. ZWECK
DIESERKLAUSELISTES,DIEHAFTUNGVONEIZOUNDDENVERTRIEBENGEGENÜBERFORDERUNGENZU
BEGRENZEN,DIEAUSDIESERBESCHRÄNKTENGARANTIEUND/ODERDEMVERKAUFENTSTEHENKÖNNEN.
Appendix
61
GARANTIE LIMITÉE
EIZO Corporation (ci-après dénommé « EIZO ») et les distributeurs autorisés par EIZO (ci-après dénommés
« Distributeurs »), sous réserve et conformément aux termes de cette garantie limitée (ci-après dénommée
« Garantie »), garantissent à l’acheteur initial (ci-après dénommé « Acheteur initial ») du produit spécifié dans la
présente (ci-après dénommé « Produit ») acheté auprès d’EIZO ou de Distributeurs agréés EIZO, que EIZO et ses
DistributeursaurontpouroptionderéparerouremplacergratuitementleProduitsil’Acheteurinitialconstate,pendantla
Périodedegarantie(définieci-dessous),qu’ilyaundysfonctionnementouqueleProduitasubiundommagedansle
cadred’uneutilisationnormaleduProduitconformémentàladescriptiondumoded’emploiquiaccompagneleProduit
(ci-aprèsdénommé«Manuel d’utilisation »).
La période de cette Garantie est limitée à (i) cinq (5) ans à partir de la date d’achat du Produit ; ou, limitée jusqu’à
l’expirationde(ii)30000heuresd’utilisationduProduit(ci-aprèsdénommée« Période de Garantie»).EIZOetses
DistributeursdéclinenttouteresponsabilitéouobligationconcernantceProduitfaceàl’Acheteurinitialouàtouteautre
personneàl’exceptiondecellesstipuléesdanslaprésenteGarantie.
EIZOetsesDistributeurscesserontdeconserveroudestockerdespièces(àl'exceptiondespiècesdeconception)du
Produitàl'expirationd'unepériodedesept(7)ansaprèsl'arrêtdelaproductiondecespièces.Pourréparerlemoniteur,
EIZOetsesdistributeursutiliserontdespiècesderechangeconformesànosnormesdecontrôlequalité.Sil'uniténe
peutpasêtreréparéeenraisondesonétatoudelarupturedestockd'unepièceadéquate,EIZOetsesDistributeurs
peuventproposerleremplacementparunproduitauxperformanceséquivalentesaulieudeleréparer.
LaGarantieestvalableuniquementdanslespaysoulesterritoiresoùsetrouventlesDistributeurs.LaGarantienelimite
aucundesdroitsreconnusparlaloiàl’Acheteurinitial.
NonobstanttouteautreclausedecetteGarantie,EIZOetsesDistributeursn’aurontd’obligationdanslecadredecette
Garantiepouraucundescasénumérésci-dessous:
(a) ToutdéfautduProduitrésultantdedommagesoccasionnéslorsdutransport,d’unemodification,d’unealtération,
d’unabus,d’unemauvaiseutilisation,d’unaccident,d’uneinstallationincorrecte,d’undésastre,d’unentretienet/
oud’uneréparationincorrectseffectuésparunepersonneautrequeEIZOousesDistributeurs;
(b) TouteincompatibilitéduProduitrésultantd’améliorationstechniqueset/ouréglementationspossibles;
(c) Toutedétériorationducapteur;
(d) Toute détérioration des performances d’affichage causée par la détérioration des éléments consommables tels
quelepanneauLCDet/oulerétroéclairage,etc.(parexempledeschangementsdeluminosité,deschangements
del’uniformitédelaluminosité,desmodificationsdecouleur,deschangementsdel’uniformitédescouleurs,des
défectuositésdepixelsycomprisdespixelsbrûlés,etc.);
(e) ToutdéfautduProduitcauséparunappareilexterne;
(f) Toutdéfautd’unProduitsurlequellenumérodesérieoriginalaétéaltéréousupprimé;
(g) Toute détérioration normale du Produit, particulièrement celle des consommables, des accessoires et/ou des
piècesreliéesauProduit(touches,élémentspivotants,câbles,Manueld’utilisationetc.),et
(h) Toute déformation, décoloration, et/ou gondolage de l’extérieur du Produit, y compris celle de la surface du
panneauLCD.
Pourbénéficierd’unservicedanslecadredecetteGarantie,l’AcheteurinitialdoitrenvoyerleProduitportpayé,dans
sonemballaged’origineoutoutautreemballageappropriéoffrantundegrédeprotectionéquivalent,auDistributeurlocal,
etassumeralaresponsabilitédesdommageset/oupertepossibleslorsdutransport.L’Acheteurinitialdoitprésenterune
preuved’achatduProduitcomprenantsadated’achatpourbénéficierdeceservicedanslecadredelaGarantie.
LaPériodedegarantiepourtoutProduitremplacéet/ouréparédanslecadredecetteGarantieexpireraàlafindela
Périodedegarantieinitiale.
EIZOOUSESDISTRIBUTEURSNESAURAIENTÊTRETENUSRESPONSABLESDESDOMMAGESOUPERTESDE
DONNÉESOUD’AUTRESINFORMATIONSSTOCKÉESDANSUNMÉDIAQUELCONQUEOUUNEAUTREPARTIE
DUPRODUITRENVOYÉÀEIZOOUAUXDISTRIBUTEURSPOURRÉPARATION.
AUCUNEAUTRE GARANTIE, EXPLICITE OU TACITE, N’EST OFFERTE PAR EIZO ET SES DISTRIBUTEURS
CONCERNANT LE PRODUIT ET SES QUALITÉS, PERFORMANCES, QUALITÉ MARCHANDE OUADAPTATION
À UN USAGE PARTICULIER. ENAUCUN CAS, EIZO OU SES DISTRIBUTEURS NE SERONT RESPONSABLES
DES DOMMAGES FORTUITS, INDIRECTS, SPÉCIAUX, INDUITS, OU DE TOUTAUTRE DOMMAGE QUEL
QU’IL SOIT (Y COMPRIS, SANS LIMITATION, LES DOMMAGES RÉSULTANT D’UNE PERTE DE PROFIT, D’UNE
INTERRUPTION D’ACTIVITÉS, D’UNE PERTE DE DONNÉES COMMERCIALES, OU DETOUTAUTRE MANQUE
À GAGNER) RÉSULTANT DE L’UTILISATION OU DE L’INCAPACITÉ D’UTILISER LE PRODUIT OUAYANT UN
RAPPORTQUELCONQUEAVECLEPRODUIT,QUECESOITSURLABASED’UNCONTRAT,D’UNTORT,D’UNE
NÉGLIGENCE,D’UNERESPONSABILITÉSTRICTEOUAUTRE,MÊMESIEIZOOUSESDISTRIBUTEURSONTÉTÉ
AVERTISDELAPOSSIBILITÉDETELSDOMMAGES.CETTELIMITATIONINCLUTAUSSITOUTERESPONSABILITÉ
QUI POURRAIT ÊTRE SOULEVÉE LORS DES RÉCLAMATIONS D’UN TIERS CONTRE L’ACHETEUR INITIAL.
L’ESSENCE DE CETTE CLAUSE EST DE LIMITER LA RESPONSABILITÉ POTENTIELLE DE EIZO ET DE SES
DISTRIBUTEURSRÉSULTANTDECETTEGARANTIELIMITÉEET/OUDESVENTES.
62
Appendix
GARANTÍA LIMITADA
EIZO Corporation (en lo sucesivo “EIZO”) y sus distribuidores autorizados (en lo sucesivo los “Distribuidores”),
conarregloydeconformidadconlostérminosdeestagarantíalimitada(enlosucesivola“Garantía”),garantizanal
compradororiginal(enlosucesivoel“Comprador original”)quecompróelproductoespecificadoenestedocumento(en
losucesivoel“Producto”)aEIZOoasusDistribuidores,queEIZOysusDistribuidores,asupropiocriterio,repararán
osustituiránelProductodeformagratuitasielCompradororiginaldetectadentrodelperiododelaGarantía(indicado
posteriormente)queelProductonofuncionacorrectamenteoquesehaaveriadoduranteelusonormaldelmismode
acuerdoconlasindicacionesdelmanualdeinstruccionessuministradoconelProducto(enlosucesivoel“Manual del
usuario”).
ElperíododevalidezdeestaGarantíaestálimitadoa(i)cinco(5)añosapartirdelafechadecompradelProductoo(ii)
a30.000horasdeusodelProducto(enadelantedesignadocomoel“Periodo de Garantía”).EIZOysusDistribuidores
notendránningunaresponsabilidadniobligaciónconrespectoalProductoparaconelCompradororiginalniparacon
tercerosquenoseanlasestipuladasenlapresenteGarantía.
EIZOysusdistribuidoresdejarándeteneroalmacenarcualquierpiezadelproducto(exceptopiezasdeldiseño)unavez
expiradoelperiododesiete(7)añosdespuésdequehayandejadodefabricarsetalespiezas.Paralareparacióndel
monitor,EIZOylosdistribuidoresutilizaránrepuestosquecumplanconnuestrosestándaresdecontroldecalidad.Sino
sepuederepararlaunidaddebidoasuestadoosisehanagotadolasexistenciasdeunapiezaimportante,EIZOysus
distribuidorespodríanofrecerlesustituirloporunproductoconrendimientoequivalenteenlugarderepararlo.
LaGarantíaesválidasóloenlospaísesyterritoriosdondeestánubicadoslosDistribuidores.LaGarantíanorestringe
ningúnderecholegaldelCompradororiginal.
A pesar de las estipulaciones de esta Garantía, EIZO y sus Distribuidores no tendrán obligación alguna bajo esta
Garantíaenningunodeloscasosexpuestosacontinuación:
(a) CualquierdefectodelProductocausadopordañoseneltransporte,modificación,alteración,abuso,usoincorrecto,
accidente, instalación incorrecta, desastre, mantenimiento incorrecto y/o reparación indebida realizada por un
terceroquenoseaEIZOosusDistribuidores.
(b) CualquierincompatibilidaddelProductodebidaaposiblesinnovacionestécnicasy/oreglamentaciones.
(c) Cualquierdeteriorodelsensor.
(d) Cualquierdeterioroenelrendimientodelavisualizacióncausadoporfallosenlaspiezasconsumiblescomoel
panelLCDy/ola"Backlight",etc.(p.ej.cambiosdebrillo,cambiosdeuniformidaddelbrillo,cambiosdecolor,
cambiosdeuniformidaddelcolor,defectosdepíxeles,incluyendopíxelesmuertos,etc.).
(e) CualquierdefectodelProductocausadoporunequipoexterno.
(f) CualquierdefectodelProductoenelquehayasidoalteradooborradoelnúmerodeserieoriginal.
(g) CualquierdeterioronormaldelProducto,yenparticulardelaspiezasconsumibles,accesoriosydemás(p.ej.
botones,piezasgiratorias,cables,Manualdelusuario,etc.).
(h) Cualquierdeformación,decoloracióny/oalabeodelexteriordelProductoincluidalasuperficiedelpanelLCD.
Para obtener servicio en los términos de esta Garantía, el Producto deberá ser enviado por el Comprador original,
asuDistribuidorlocal,coneltransportepreviamentepagado,enelembalajeoriginaluotroembalajeadecuadoque
ofrezcaelmismogradodeprotección,asumiendoelriesgodedañosy/opérdidadelProductoduranteeltransporte.El
CompradororiginaldeberápresentaruncomprobantedecompradelProductoenelquesereflejelafechadecompra
delmismocuandolosoliciteelserviciodeGarantía.
ElPeriododegarantíaparacualquierProductoreemplazadoy/oreparadoenlostérminosdeestaGarantíaexpiraráal
vencerelPeriododegarantíaoriginal.
EIZO O LOS DISTRIBUIDORESAUTORIZADOS DE EIZO NO SE RESPONSABILIZAN DE NINGÚN DAÑO O
PÉRDIDAQUEPUEDANSUFRIRLOSDATOSUOTRAINFORMACIÓNALMACENADAENCUALQUIERMEDIOO
CUALQUIERPARTEDECUALQUIERPRODUCTODEVUELTOAEIZOOALOSDISTRIBUIDORESDEEIZOPARA
SUREPARACIÓN.
EIZOY LOS DISTRIBUIDORESAUTORIZADOS DE EIZO NO OFRECEN NINGUNA OTRA GARANTÍA, IMPLÍCITA
NI EXPLÍCITA, CON RESPECTOAL PRODUCTO YA SU CALIDAD, RENDIMIENTO, COMERCIABILIDAD E
IDONEIDADPARACUALQUIERUSOENPARTICULAR.ENNINGÚNCASOSERÁNEIZOOLOSDISTRIBUIDORES
AUTORIZADOSDEEIZORESPONSABLESDENINGÚNDAÑOEMERGENTE,INDIRECTO,ESPECIAL,INHERENTE
O CUALQUIERA QUE SEA (INCLUYENDO, SIN LIMITACIÓN, DAÑOS POR LUCRO CESANTE, INTERRUPCIÓN
DE LAACTIVIDAD COMERCIAL, PÉRDIDA DE INFORMACIÓN COMERCIAL O CUALQUIER OTRA PÉRDIDA
PECUNIARIA)QUESEDERIVEDELUSOOIMPOSIBILIDADDEUSODELPRODUCTOOENRELACIÓNCONEL
PRODUCTO,YA SEA BASADO EN CONTRATO, PORAGRAVIO, NEGLIGENCIA, ESTRICTA RESPONSABILIDAD
O CUALQUIERA QUE SEA,AUN CUANDO SE HAYAADVERTIDOA EIZO OA LOS DISTRIBUIDORES DE EIZO
DELAPOSIBILIDADDETALESDAÑOS.ESTAEXCLUSIÓNTAMBIÉNABARCACUALQUIERRESPONSABILIDAD
QUE PUEDA DERIVARSE DE RECLAMACIONES HECHAS POR UN TERCERO CONTRA EL COMPRADOR
ORIGINAL.LAESENCIADEESTAESTIPULACIÓNESLIMITARLARESPONSABILIDADPOTENCIALDEEIZOYLOS
DISTRIBUIDORESQUEPUDIERADERIVARSEDEESTAGARANTÍALIMITADAY/OVENTAS.
Appendix
63
GARANZIA LIMITATA
EIZOCorporation(acuisifaràriferimentodaquiinpoicon“EIZO”)ediDistributoriautorizzatidaEIZO(acuisifarà
riferimento da qui in poi con “Distributori”) garantiscono, secondo i termini di questa garanzia limitata (a cui si farà
riferimentodaquiinpoicon“Garanzia”)all’acquirenteoriginale(acuisifaràriferimentodaquiinpoicon“Acquirente
originale”) che ha acquistato il prodotto specificato in questo documento (a cui si farà riferimento da qui in poi con
“Prodotto”)daEIZOodaisuoiDistributori,cheEIZOeidistributori,alorodiscrezione,riparerannoosostituirannoil
Prodottosenzaaddebitosel’Acquirenteoriginaletrova,entroilperiododellaGaranzia(definitosotto),cheilProdotto
malfunzionaesièdanneggiatonelcorsodelsuonormaleutilizzoosservandoleindicazionidelmanualediistruzioni
allegatoalProdotto(acuisifaràriferimentodaquiinpoicon“Manuale utente”).
LapresenteGaranziaèlimitataa(i)cinque(5)anniapartiredalladatad'acquistodelProdottoo(ii)alloscaderedi
30.000 ore d'utilizzo del Prodotto (a cui si farà riferimento da qui in poi con “Periodo di Garanzia”). EIZO e i suoi
DistributorinonsiassumonoalcunaresponsabilitàenonhannoalcunobbligoriguardoalProdottoversol'Acquirente
originaleoterzidiversidaquellirelativiaquestaGaranzia.
EIZO e i distributori cesseranno lo stoccaggio dei componenti (tranne le parti relative al progetto) del prodotto dopo
sette(7)annidall’interruzionedellaproduzioneditalicomponenti.Perlariparazionedelmonitor,EIZOeiDistributori
utilizzerannopartidiricambioconformiainostristandarddicontrollodellaqualità.Sel’unitànonpuòessereriparataa
causadellesuecondizioniodell’esaurimentoscortediuncomponenterilevante,EIZOeidistributoripotrebberooffrirela
sostituzioneconunprodottoconprestazioniequivalentipiuttostoripararlo.
La Garanzia è valida soltanto nei paesi dove ci sono i Distributori EIZO. La Garanzia non limita alcun diritto legale
dell’Acquirenteoriginale.
IndipendentementedaqualsiasialtracondizionediquestaGaranzia,EIZOeisuoiDistributorinonavrannoalcunobbligo
derivantedaquestaGaranziainognunodeicasielencatidiseguito:
(a) QualsiasidifettodelProdottocausatodadanniditrasporto,modifiche,alterazioni,abusi,usiimpropri,incidenti,
installazioneerrata,calamità,manutenzioneerratae/oriparazioniimproprieeseguitedaterzepartichenonsiano
EIZOoisuoiDistributori.
(b) QualsiasiincompatibilitàdelProdottodovutaapossibiliinnovazionitecnichee/onormative.
(c) Qualsiasideterioramentodelsensore.
(d) Qualsiasideterioramentodelleprestazionidelloschermocausatodaldeterioramentodelleparticonsumabili,come
ilpannelloLCDe/olaretroilluminazione,ecc.(peresempio:icambiamentidiluminosità,cambiamentidiuniformità
della luminosità, i cambiamenti di colore, i cambiamenti di uniformità del colore, i difetti dei pixel, inclusi i pixel
bruciati,ecc.).
(e) QualsiasidifettodelProdottocausatodaapparecchiatureesterne.
(f) QualsiasidifettodelProdottoincuiilnumerodiserieoriginalesiastatoalteratoorimosso.
(g) Qualsiasi normale deterioramento del Prodotto, in particolar modo nelle sue parti di consumo, accessori, e/o
attacchi(peresempio:tasti,partirotanti,cavi,Manualedell’utente,ecc.).
(h) Qualsiasitipodideformazione,scolorimento,e/odiinvolucroesternodelProdottoinclusalasuperficiedelpannello
LCD.
Per ricevere assistenza tecnica con questa Garanzia, l’Acquirente originale deve inviare il Prodotto, con trasporto
pre-pagato, nella sua confezione originale o altraconfezioneadeguatachefornisceunlivelloanalogodiprotezione,
assumendosiilrischiodidannie/operditaintransito,alDistributorelocale.L’Acquirenteoriginaledevepresentarela
provadiacquistochestabilisceladatadiacquistodelProdottoquandorichiedeserviziosottoGaranzia.
IlPeriododigaranziaperqualsiasiProdottosostituitoe/oriparatosottoquestaGaranziascadeallafinedelPeriododi
garanziaoriginale.
EIZOOISUOIDISTRIBUTORINONSONORESPONSABILIPERQUALSIASIDANNOOPERDITADIDATIOALTRE
INFORMAZIONI MEMORIZZATI SU QUALSIASI SUPPORTO O QUALSIASI PARTE DI QUALSIASI PRODOTTO
INVIATOAEIZOOISUOIDISTRIBUTORIPERRIPARAZIONI.
EIZO E I SUOI DISTRIBUTORI NON OFFRONOALCUNA GARANZIAADDIZIONALE, IMPLICITA O ESPLICITA,
RIGUARDO IL PRODOTTO E LA SUA QUALITÀ, PRESTAZIONI, VENDIBILITÀ OAPPROPRIATEZZA PER
QUALSIASI USO PARTICOLARE. IN NESSUN CASO EIZO O I DISTRIBUTORI EIZOAUTORIZZATI SARANNO
RESPONSABILI PER QUALSIASI DANNOACCIDENTALE, INDIRETTO, SPECIALE, CONSEGUENTE O DI
QUALSIASIALTRANATURA(INCLUSI,SENZALIMITI,DANNIPERPERDITADIPROFITTI,INTERRUZIONEDELLE
ATTIVITÀ, PERDITA DI INFORMAZIONI D’AFFARI O QUALSIASIALTRA PERDITA PECUNIARIA) DERIVANTI
DALL’USO O DALL’IMPOSSIBILITÀ DI USARE IL PRODOTTO O IN QUALSIASI RELAZIONEAL PRODOTTO,
SIA SU BASE DI CONTRATTO, TORTO, NEGLIGENZA, STRETTA RESPONSABILITÀ OALTRIMENTI,ANCHE
SE EIZO O I DISTRIBUTORI EIZOAUTORIZZATI SONO STATIAVVERTITI DELLA POSSIBILITÀ DITALI DANNI.
QUESTAESCLUSIONEINCLUDEANCHEQUALSIASIRESPONSABILITÀCHEPOSSAINSORGEREDARECLAMI
DI TERZI CONTRO L’ACQUIRENTE ORIGINALE. L’ESSENZA DI QUESTO PROVVEDIMENTO È LIMITARE LA
RESPONSABILITÀPOTENZIALEDIEIZOEDEIDISTRIBUTORIDERIVANTEDAQUESTAGARANZIALIMITATAE/O
DALLEVENDITE.
64
Appendix
BEGRÄNSAD GARANTI
EIZOCorporation(nedankallat“EIZO”)ochEIZOsauktoriseradedistributörer(nedankallade“Distributörer”)garanterar
ienlighetmedvillkorenidennabegränsadegaranti(nedankallad“Garantin”)denursprungligeköparen(nedankallad
den“Ursprunglige köparen”)somköptedenidokumentetspecificeradeprodukten(nedankallad“Produkten”)från
EIZOellerDistributörer,attEIZOellerDistributörerenligtegetgottfinnandekostnadsfrittantingenrepareraellerbytaut
dendefektaProduktenomdenUrsprungligeköpareninomGarantiperioden(definierasnedan)upptäckerattProdukten
fungerarfelaktigtellerskadasundernormalanvändningavProduktenienlighetmedbeskrivningenibruksanvisningen
(nedankallad“Bruksanvisning”).
Giltighetsperiodenfördennagarantiärbegränsadtill(i)fem(5)årfråndatumetförProduktensinköpeller,omdetta
inträffartidigare,begränsattillutlöpandetav(ii)30000timmarsanvändningavProdukten(härikallad“Garantiperioden”).
EIZOochDistributörerskainteundernågravillkorhanågotannatansvaränvadsomangesidennagarantigällande
ProduktenirelationtilldenUrsprungligeköparenellertredjepart.
EIZOochdessleverantörerslutarlagerföradelar(utomdesigndelar)tillproduktensju(7)årefterattdelenifrågaslutar
tillverkas.NätskärmenreparerasanvänderEIZOochdistributörerreservdelarsomuppfyllervårakvalitetsstandarder.
OmenhetenintekanrepareraspågrundavskicketellerattendelintefinnsilagerkanEIZOochdessleverantörer
erbjudasigattbytautproduktenmotenproduktmedlikvärdigprestandaiställetförattrepareraden.
Garantin är endast giltig i de länder där det finns Distributörer. Garantin begränsar inte några av den Ursprunglige
köparenslagstadgaderättigheter.
OavsettandravillkoridennagarantiskainteEIZODistributörerundernågravillkorhanågotansvarinågotavdefall
sombeskrivsnedan:
(a) När någon bristfällighet hos Produkten kan härledas till att ha uppstått vid frakt, modifiering, ändring, felaktigt
handhavande,olycka,felaktiginstallation,katastrof,felaktigtunderhålloch/ellerfelaktigreparationutfördavtredje
partannanänEIZOochDistributörer.
(b) AllaformeravinkompatibilitethosProduktenpågrundavmöjligatekniskainnovationeroch/ellerbestämmelser.
(c) Allaförsämringaravsensorn.
(d) Alla försämringar av bildens prestanda beroende på förbrukningsdelar så som LCD-panel och/eller
bakgrundsbelysningetc.(t.ex.ändringariljusstyrka,jämnhetiljusstyrka,färg,färgjämnhet,defektapixlaroch/eller
fastlysandepixlaretc.).
(e) AlladefekterhosProduktensomorsakatsavexternutrustning.
(f) AlladefekterhosProduktenpåvilkendetursprungligaserienumretharändratselleravlägsnats.
(g) All normal försämring av Produkten, speciellt förbrukningsartiklar, tillbehör och/eller yttre delar (t.ex. knappar,
roterandedelar,kablar,Bruksanvisningenetc.).
(h) Varjedeformation,missfärgningoch/ellerskevhetavProduktensyttreinklusiveytanpåLCD-panelen.
För att erhålla service under denna garanti måste den Ursprunglige köparen (med hänseende till risken för skada
och/ellerförlustundertransport)levereraProduktentillnärmasteDistributörmedförebetaldfrakt,idessursprungliga
förpackning eller annan fullgod förpackning som ger likvärdigt skydd. Den Ursprunglige köparen måste kunna visa
inköpsbevisförProduktensomklargörProduktensinköpsdatumvidbegäranavgarantiservice.
Garantiperiodenförallautbyttaoch/ellerrepareradeprodukterunderdennagarantiskallupphöravidutgångenavden
ursprungligaGarantiperioden.
EIZOELLERDISTRIBUTÖRERÄRINTEANSVARIGAFÖRNÅGONFORMAVSKADAELLERFÖRLUSTAVDATA
ELLERANNAN INFORMATION SOM HAR LAGRATS I NÅGON FORMAV MEDIA ELLERANNAN DELAV NÅGON
PRODUKTSOMHARRETURNERATSTILLEIZOELLERDISTRIBUTÖRERFÖRREPARATION.
EIZO OCH DISTRIBUTÖRERNA GARANTERAR INGET, UTTRYCKLIGEN ELLER UNDERFÖRSTÅTT, VAD
BETRÄFFARPRODUKTENOCHDESSKVALITET,PRESTANDA,SÄLJBARHETELLERLÄMPLIGHETFÖRNÅGON
FORMAVSPECIELLANVÄNDNING.UNDERINGAOMSTÄNDIGHETERSKALLEIZOELLERDISTRIBUTÖRERNA
HÅLLASANSVARIGAFÖRNÅGRASOMHELSTUNDERORDNADE,INDIREKTA,SPECIELLA,DÄRAVFÖLJANDE
ELLER ÖVRIGA SKADOR (INKLUSIVE, UTAN BEGRÄNSNING TILL, SKADOR FÖR FÖRLUSTAV INKOMST,
AVBRUTENAFFÄRSRÖRELSE,FÖRLUSTAVAFFÄRSINFORMATIONELLERANNANSÄRSKILDFÖRLUST)SOM
UPPSTÅTT SOM ETT RESULTATAVANVÄNDNING ELLER OFÖRMÅGAATTANVÄNDA PRODUKTEN ELLER I
NÅGON FORMAVANSLUTNINGTILL PRODUKTERNA, VARE SIG DETTA GRUNDAS PÅ KONTRAKT, ÅTALBAR
HANDLING,FÖRSUMLIGHET,ANSVARSSKYLDIGHETELLERANNAT,ÄVENOMEIZOELLERDISTRIBUTÖRERNA
HAR INFORMERATS BETRÄFFANDE MÖJLIGHETATT SÅDANA SKADOR FÖRELIGGER. DETTA UNDANTAG
OMFATTARÄVENALLFORMAVANSVARSSKYLDIGHETSOMKANUPPSTÅGENOMENTREDJEPARTSANSPRÅK
GENTEMOTDENURSPRUNGLIGEKÖPAREN.GRUNDBESTÅNDSDELENIBESTÄMMELSENÄRATTBEGRÄNSA
DETEVENTUELLAANSVARSTAGANDETFÖREIZOOCHDISTRIBUTÖRERNASOMKANUPPSTÅGENOMDENNA
BEGRÄNSADEGARANTIOCH/ELLERFÖRSÄLJNING.
Appendix
65
ΠΕΡΙΟΡΙΣΜΕΝΗ ΕΓΓΥΗΣΗ
Η EIZO Corporation (στο εξής «EIZO») και οι διανομείς που εξουσιοδοτεί η EIZO (στο εξής «Διανομείς»)
παρέχουν εγγύηση, υποκείμενη και σύμφωνα με τους όρους της παρούσας περιορισμένης εγγύησης (στο εξής
«Εγγύηση»),στοναρχικόαγοραστή(στοεξής«Αρχικός Αγοραστής»)οοποίοςαγόρασετοπροϊόνπουκαθορίζεταιστο
παρόνέγγραφο(στοεξής«Προϊόν»)απότηνEIZOήτουςΔιανομείς,ηοποίαεξασφαλίζειότιηEIZOκαιοιΔιανομείς,
σύμφωναμετηδιακριτήευχέρειάτους,είτεθαεπισκευάσουνείτεθααντικαταστήσουντοΠροϊόνχωρίςχρέωσηεάνο
ΑρχικόςΑγοραστής αντιληφθεί εντός της ΠεριόδουΕγγύησης(ορίζεταικατωτέρω)ότιτοΠροϊόνδυσλειτουργείήέχει
υποστείβλάβηκατάτηδιάρκειακανονικήςχρήσηςτουΠροϊόντοςσύμφωναμετηνπεριγραφήστοεγχειρίδιοχρήσηςπου
συνοδεύειτοΠροϊόν(στοεξής«Εγχειρίδιο Χρήστη»).
ΗπερίοδοςτηςπαρούσαςΕγγύησηςείναι(i)πέντε(5)έτηαπότηνημερομηνίααγοράςτουΠροϊόντος,ή,στηλήξητων
(ii)30.000ωρώνχρήσηςτουΠροϊόντος(στοεξής«Περίοδος Εγγύησης»).ΗEIZOκαιοιΔιανομείςδενφέρουνκαμία
ευθύνηήυποχρέωσηόσοναφοράτοΠροϊόνσεσχέσημετονΑρχικόΑγοραστήήοποιοδήποτετρίτομέρος,ούτεάλλη
ευθύνηδιαφορετικήαπόαυτήνπουπαρέχεταιστηνπαρούσαΕγγύηση.
ΗEIZOκαιοιδιανομείςτηςθαπάψουνναδιατηρούναποθέματαεξαρτημάτων(εκτόςαπόταεξαρτήματασχεδιασμού)
του προϊόντος μόλις περάσουν επτά (7) χρόνια αφότου διακοπεί η παραγωγή των εν λόγω εξαρτημάτων. Κατά την
επισκευήτηςοθόνης,ηEIZOκαιοιΔιανομείςθαχρησιμοποιήσουνανταλλακτικάεπισκευήςπουσυμμορφώνονταιμε
ταπρότυπάμαςγιατηΔιασφάλισηΠοιότητας.Ανδενείναιεφικτήηεπισκευήτηςμονάδαςλόγωτηςκατάστασήςτηςή
λόγωέλλειψηςαποθεμάτωνκάποιουσχετικούεξαρτήματος,ηEIZOκαιοιδιανομείςτηςενδέχεταινασαςπροσφέρουντη
δυνατότητααντικατάστασήςτηςμεπροϊόνισοδύναμωνεπιδόσεωναντίνατηνεπισκευάσουν.
Η Εγγύηση ισχύει μόνο σε χώρες ή περιοχές όπου βρίσκονται οιΔιανομείς. Η Εγγύηση δεν περιορίζει οποιαδήποτε
νόμιμαδικαιώματατουΑρχικούΑγοραστή.
ΛαμβανομένηςυπόψηκάθεδιάταξηςτηςπαρούσαςΕγγύησης,ηEIZOκαιοιΔιανομείςδενθαέχουνκαμίααπολύτως
υποχρέωσησύμφωναμετηνπαρούσαΕγγύησησεοποιαδήποτεαπότιςπεριπτώσειςπουδιατυπώνονταικατωτέρω:
(α) ΤυχόνελάττωματουΠροϊόντοςπουπροκαλείταιαπόζημιάκατάτημεταφορά,τροποποίηση,αλλαγή,κατάχρηση,
λανθασμένη χρήση, ατύχημα, λανθασμένηεγκατάσταση,καταστροφή,εσφαλμένησυντήρησηή/καιλανθασμένη
επισκευήαπότρίτομέροςεκτόςτηςEIZOκαιτωνΔιανομέων,
(β) ΤυχόνασυμβατότητατουΠροϊόντοςλόγωπιθανώντεχνικώνκαινοτομιώνή/καικανονισμών,
(γ) Τυχόνεπιδείνωσητουαισθητήρα,
(δ) Τυχόν επιδείνωση της απόδοσης οθόνης που προκαλείται από τη φθορά αναλώσιμων εξαρτημάτων όπως
της οθόνης LCD ή/και του φωτός υποβάθρου, κτλ. (π.χ. αλλαγές στη φωτεινότητα, αλλαγές στην ομοιομορφία
φωτεινότητας,αλλαγέςστοχρώμα,αλλαγέςστηνομοιομορφίαχρώματος,ελαττώματασεpixelπεριλαμβανομένων
τωνκαμένωνpixel,κτλ.),
(ε) ΤυχόνελάττωματουΠροϊόντοςπουπροκαλείταιαπόεξωτερικόεξοπλισμό,
(στ)ΤυχόνελάττωματουΠροϊόντοςστοοποίοέχειτροποποιηθείήαφαιρεθείογνήσιοςαριθμόςσειράς,
(ζ) Τυχόν φυσιολογική φθορά του προϊόντος, ιδιαίτερα αυτής των αναλώσιµων, των αξεσουάρ ή/και των
προσαρτηµάτων(π.χ.κουµπιά,περιστρεφόµεναµέρη,καλώδια,ΕγχειρίδιοΧρήστη,κτλ.),και
(η) Τυχόν παραμόρφωση, αποχρωματισμό ή/και διαστρέβλωση του εξωτερικού μέρους του προϊόντος,
περιλαμβανομένηςτηςεπιφάνειαςτηςοθόνηςLCD.
ΟΑρχικόςΑγοραστήςγιαναδικαιούταιυπηρεσίεςεπισκευήςσύμφωναμετηνΕγγύηση,θαπρέπειναπαραδώσειτο
Προϊόν, με πληρωμένα τα μεταφορικά έξοδα, στηναρχικήτουσυσκευασίαήσεάλληεπαρκήσυσκευασίαμεισότιμο
βαθμόπροστασίας,αναλαμβάνονταςτονκίνδυνοβλάβηςή/καιαπώλειαςκατάτημεταφορά,στοντοπικόΔιανομέα.Ο
ΑρχικόςΑγοραστήςότανζητάυπηρεσίεςεπισκευήςσύμφωναμετηνΕγγύηση,θαπρέπειναπροσκομίζειτηναπόδειξη
αγοράςτουΠροϊόντοςκαιτηνημερομηνίατηςαγοράς.
Η Περίοδος Εγγύησης για οποιοδήποτε αντικατεστημένο ή/και επισκευασμένο προϊόν σύμφωνα με την παρούσα
ΕγγύησηλήγειστοτέλοςτηςαρχικήςΠεριόδουΕγγύησης.
Η EIZO Ή ΟΙΔΙΑΝΟΜΕΙΣΔΕΝ ΕΥΘΥΝΟΝΤΑΙ ΓΙΑ ΟΠΟΙΑΔΗΠΟΤΕ ΒΛΑΒΗ ΉΑΠΩΛΕΙΑΔΕΔΟΜΕΝΩΝ ΉΑΛΛΩΝ
ΠΛΗΡΟΦΟΡΙΩΝ ΠΟΥΑΠΟΘΗΚΕΥΟΝΤΑΙ ΣΕ ΟΠΟΙΟΔΗΠΟΤΕ ΜΕΣΟ Ή ΟΠΟΙΟΔΗΠΟΤΕΑΛΛΟ ΜΕΡΟΣ ΣΕ
ΟΠΟΙΟΔΗΠΟΤΕΠΡΟΪΟΝΠΟΥΕΠΙΣΤΡΕΦΕΤΑΙΣΤΗΝEIZOΉΣΕΔΙΑΝΟΜΕΑΓΙΑΕΠΙΣΚΕΥΗ.
Η EIZO ΚΑΙ ΟΙΔΙΑΝΟΜΕΙΣΔΕΝ ΠΑΡΕΧΟΥΝ ΚΑΜΙΑ ΠΕΡΑΙΤΕΡΩ ΕΓΓΥΗΣΗ, ΡΗΤΗ Ή ΣΥΝΕΠΑΓΟΜΕΝΗ, ΟΣΟΝ
ΑΦΟΡΑΤΟ ΠΡΟΪΟΝ ΚΑΙΤΗΝ ΠΟΙΟΤΗΤΑ,ΤΗΝΑΠΟΔΟΣΗ,ΤΗΝ ΕΜΠΟΡΕΥΣΙΜΟΤΗΤΑ ΉΤΗΝ ΚΑΤΑΛΛΗΛΟΤΗΤΑ
ΤΟΥ ΓΙΑ ΟΠΟΙΑΔΗΠΟΤΕ ΣΥΓΚΕΚΡΙΜΕΝΗ ΧΡΗΣΗ. ΣΕ ΚΑΜΙΑ ΠΕΡΙΠΤΩΣΗ Η EIZO Ή ΟΙΔΙΑΝΟΜΕΙΣΔΕΝ
ΘΑ ΕΥΘΥΝΟΝΤΑΙ ΓΙΑ ΚΑΜΙΑΑΠΟΛΥΤΩΣ ΤΥΧΑΙΑ, ΕΜΜΕΣΗ, ΕΙΔΙΚΗ, ΣΥΝΕΠΑΓΟΜΕΝΗ ΉΑΛΛΗ ΒΛΑΒΗ
(ΠΕΡΙΛΑΜΒΑΝΟΜΕΝΩΝ, ΜΕΤΑΞΥΑΛΛΩΝ, ΒΛΑΒΩΝ ΉΑΠΩΛΕΙΑΣ ΚΕΡΔΩΝ,ΔΙΑΚΟΠΗΣ ΕΠΙΧΕΙΡΗΜΑΤΙΚΩΝ
ΔΡΑΣΤΗΡΙΟΤΗΤΩΝ,ΑΠΩΛΕΙΑΣΕΠΙΧΕΙΡΗΜΑΤΙΚΩΝΠΛΗΡΟΦΟΡΙΩΝΉΤΥΧΟΝΑΛΛΗΣΧΡΗΜΑΤΙΚΗΣΑΠΩΛΕΙΑΣ)
ΠΟΥΠΡΟΚΥΠΤΕΙΑΠΟΤΗΧΡΗΣΗΉΤΗΝΑΝΙΚΑΝΟΤΗΤΑΧΡΗΣΗΣΤΟΥΠΡΟΪΟΝΤΟΣΉΤΥΧΟΝΑΛΛΗΣΣΥΝΔΕΣΗΣ
ΜΕΤΟΠΡΟΪΟΝ,ΕΙΤΕΒΑΣΙΖΕΤΑΙΣΕΣΥΜΒΟΛΑΙΟ,ΒΛΑΒΗ,ΑΜΕΛΕΙΑ,ΑΥΣΤΗΡΗΕΥΘΥΝΗΉΕΙΔΑΛΛΩΣ,ΑΚΟΜΗ
ΚΙΕΑΝΗEIZOΉΟΙΔΙΑΝΟΜΕΙΣΕΝΗΜΕΡΩΘΟΥΝΓΙΑΤΗΝΠΙΘΑΝΟΤΗΤΑΤΕΤΟΙΩΝΖΗΜΙΩΝ.ΗΕΞΑΙΡΕΣΗΑΥΤΗ
ΠΕΡΙΛΑΜΒΑΝΕΙ ΕΠΙΣΗΣ ΟΠΟΙΑΔΗΠΟΤΕ ΕΥΘΥΝΗΕΝΔΕΧΕΤΑΙΝΑΠΡΟΚΥΨΕΙΑΠΟΑΞΙΩΣΕΙΣΤΡΙΤΟΥΜΕΡΟΥΣ
ΚΑΤΑΤΟΥΑΡΧΙΚΟΥΑΓΟΡΑΣΤΗ. Η ΟΥΣΙΑΤΟΥΟΡΟΥΑΥΤΟΥΕΙΝΑΙΝΑΠΕΡΙΟΡΙΣΕΙΤΗΝΠΙΘΑΝΗΕΥΘΥΝΗΤΗΣ
EIZOΚΑΙΤΩΝΔΙΑΝΟΜΕΩΝΠΟΥΠΡΟΚΥΠΤΕΙΑΠΟΤΗΝΠΑΡΟΥΣΑΕΓΓΥΗΣΗΉ/ΚΑΙΤΙΣΠΩΛΗΣΕΙΣ.
66
Appendix
ОГРАНИЧЕННАЯ ГАРАНТИЯ
EIZO Corporation (называемая в дальнейшем “EIZO”) и авторизированные EIZO дистрибуторы (называемые в
дальнейшем“Дистрибуторы”)гарантируют,всоответствиисусловиямиипунктамиэтойограниченнойгарантии
(называемойвдальнейшем“Гарантия”),первичномупокупателю(называемомувдальнейшем“Первоначальный
покупатель”),которыйприобрелуEIZOилиДистрибуторовпродукт,указанныйвэтомдокументе(называемый
в дальнейшем “Продукт”), что EIZO или Дистрибуторы на свое усмотрение либо бесплатно отремонтируют,
либо бесплатно заменят Продукт, если Первоначальный покупатель признает в пределах Гарантийного срока
(определенногониже),чтоПродуктнеисправенилионповрежденпроцессенормальногоиспользованияпродукта
всоответствиисописаниемвинструкциипоэксплуатации,прилагаемойкПродукту(называемойвдальнейшем
“Руководство пользователя”).
Гарантийныйпериодограниченсроком(i)пять(5)летотдатыприобретенияПродуктаилиограниченсроком(ii)30
000часовиспользованияПродукта(называемыйвдальнейшем“Гарантийный период”).EIZOиДистрибуторыне
несутникакойответственностиинеберутобязательствотносительноПродуктапоотношениюкПервоначальному
покупателюилипоотношениюклюбымтретьимсторонам,кромеобязательств,оговоренныхвэтойГарантии.
КомпанияEIZOиеедистрибьюторыхранятдеталиизделия(заисключениемдеталейвнешнейконструкции)неболее
7(семи)летпослепрекращенияеговыпуска.ВслучаеремонтамонитораEIZOиДистрибьюторыбудутиспользовать
запчасти, которые соответствуют нашим стандартам QC (контроль качества). Если устройство невозможно
отремонтировать из-за его состояния или отсутствия нужной детали, то вместо ремонта компания EIZO и ее
дистрибьюторымогутпредлагатьзаменунеисправногоустройстванаустройствосаналогичнымихарактеристиками.
Гарантия действительна только в странах или регионах, где расположены Дистрибуторы. Гарантия не
ограничиваетникакиезаконныеправаПервоначальногопокупателя.
НесмотрянадругиеусловияэтойГарантииEIZOиДистрибуторыненесутникакихобязательствсогласноэтой
Гарантиивлюбомизперечисленныхнижеслучаев:
(а) Любые дефекты Продукта, вызванные повреждениями при перевозке, модификацией, изменением,
неправильным обращением, неправильным использованием, авариями, неправильной установкой,
стихийнымибедствиями,неправильнымуходоми/илинеправильнымремонтомтретьейстороной,отличной
отEIZOилиДистрибуторов;
(б) Любые несовместимости Продукта из-за технических усовершенствований и/или изменения технических
норм;
(в) Любоеповреждениедатчика;
(г) Любые ухудшения работы дисплея, вызванные изнашиванием невосстановимых частей, таких как
панельЖКДи/илиподсветкаит.д.(например,изменениевяркости,изменениевравномерностияркости,
изменениевцветности,изменениевравномерностицветности,изменениевпикселах,включаявыгоревшие
пикселыит.д.);
(д) ЛюбыедефектыПродукта,вызванныевнешнимоборудованием;
(е) ЛюбыедефектыПродукта,прикоторыхоригинальныйсерийныйномербылизмененилиудален;
(ж) Любые естественные ухудшения продукта, в частности, вызванные износом расходных частей,
принадлежностей и/или приспособлений (например, кнопок, вращающихся частей, кабелей, Руководства
пользователяит.д.);и
(з) Любые деформации, изменения цвета и/или коробления внешней поверхности продукта, включая
поверхностьпанелиЖКД.
Чтобы получить техническое обслуживание в рамках Гарантии, Первоначальный покупатель должен доставить
Продукт местному Дистрибутору, оплатив перевозку, в его оригинальной упаковке или в другой соответствующей
упаковке,обеспечивающейравноценнуюстепеньзащиты,принимаявовниманиерискповрежденияи/илиутерюпри
транспортировке. При запросе технического обслуживания в рамках Гарантии Первоначальный покупатель должен
предоставитьсвидетельствопокупкипродуктаидатыпокупки.
Гарантийныйпериоддлялюбогозамененногои/илиотремонтированногопродуктаврамкахГарантииистекаетвконце
завершениясрокадействияоригинальногоГарантийногопериода.
EIZOИЛИДИСТРИБУТОРЫНЕНЕСУТОТВЕТСТВЕННОСТИЗАЛЮБЫЕПОВРЕЖДЕНИЯИЛИУТЕРЮДАННЫХИЛИ
ДРУГОЙ ИНФОРМАЦИИ, ХРАНЯЩИХСЯ НА КАКИХ-ЛИБО НОСИТЕЛЯХ ИНФОРМАЦИИ ИЛИ НА ЛЮБЫХ ДРУГИХ
ЧАСТЯХПРОДУКТА,КОТОРЫЙВОЗВРАЩЕНEIZOИЛИДИСТРИБУТОРАМДЛЯРЕМОНТА.
EIZOИДИСТРИБУТОРЫНЕДАЮТНИКАКОЙДАЛЬНЕЙШЕЙГАРАНТИИ,ВЫРАЖЕННОЙИЛИПОДРАЗУМЕВАЕМОЙ,
ОТНОСИТЕЛЬНО ПРОД УКТА И ЕГО КАЧЕСТВА, ТЕХНИЧЕСКИХ ХАРАКТЕРИСТИК, ТОВАРНОСТИ ИЛИ
СООТВЕТСТВИЯ ДЛЯ КАКОГО-ЛИБО ОПРЕДЕЛЕННОГО ИСПОЛЬЗОВАНИЯ. НИ ПРИ КАКИХ УСЛОВИЯХ EIZO
ИЛИ ДИСТРИБУТОРЫ НЕ НЕСУТ ОТВЕТСТВЕННОСТИ ЗА ЛЮБОЙ СЛУЧАЙНЫЙ, КОСВЕННЫЙ, СПЕЦИАЛЬНЫЙ,
ПОБОЧНЫЙ ИЛИ ИНОЙ УЩЕРБ (ВКЛЮЧАЯ, БЕЗ ОГРАНИЧЕНИЙ, УЩЕРБ ИЗ-ЗА НЕПОЛУЧЕННОЙ ПРИБЫЛИ,
ПРЕРЫВАНИЯ БИЗНЕСА, ПОТЕРИ КОММЕРЧЕСКОЙ ИНФОРМАЦИИ ИЛИ ЛЮБЫЕ ДРУГИЕ ФИНАНСОВЫЕ
ПОТЕРИ), ВОЗНИКШИЙ ИЗ-ЗА ИСПОЛЬЗОВАНИЯ ИЛИ НЕВОЗМОЖНОСТИ ИСПОЛЬЗОВАТЬ ПРОДУКТ ИЛИ В
ЛЮБОЙДРУГОЙСВЯЗИСПРОДУКТОМ,ЛИБООСНОВАННЫЙНАКОНТРАКТНЫХОТНОШЕНИЯХ,ГРАЖДАНСКИХ
ПРАВОНАРУШЕНИЯХ, НЕБРЕЖНОСТИ, ПРИЧИНЕНИЯ УЩЕРБА ТРЕТЬЕЙ СТОРОНЕ ИЛИ ЧЕМ-ЛИБО ЕЩЕ, ДАЖЕ
ЕСЛИ EIZO ИЛИ ДИСТРИБУТОРЫ БЫЛИ УВЕДОМЛЕНЫ О ВОЗМОЖНОСТИ ТАКОГО УЩЕРБА. ЭТО ИСКЛЮЧЕНИЕ
ТАКЖЕ ВКЛЮЧАЕТ ЛЮБЫЕ ОБЯЗАТЕЛЬСТВА, КОТОРЫЕ МОГУТ ВОЗНИКНУТЬ В РЕЗУЛЬТАТЕ ТРЕБОВАНИЙ
ТРЕТЬЕЙ СТОРОНЫ В ОТНОШЕНИИ ПЕРВОНАЧАЛЬНОГО ПОКУПАТЕЛЯ. СУЩЕСТВОМ ЭТОГО ПОЛОЖЕНИЯ
ЯВЛЯЕТСЯОГРАНИЧЕНИЕПОТЕНЦИАЛЬНОЙОТВЕТСТВЕННОСТИEIZOИДИСТРИБУТОРОВ,ВОЗНИКАЮЩЕЙИЗЗАЭТОЙОГРАНИЧЕННОЙГАРАНТИИИ/ИЛИПРОДАЖ.
Appendix
67
有限责任保证书
EIZOCorporation(以下简称 “EIZO”)和 EIZO 授权的经销商(以下简称 “经销商”),接受并依照本有限责任保证书(以
下简称 “保证书”)之条款,向从 EIZO 和经销商购买本文中所规定产品(以下简称 “产品”)的原买方(以下称 “原买方”)
提供保证 :在保证期内(规定如下),如果原买方发现按本产品所附使用说明书(以下简称 “用户手册”)所述方式正常使
用本产品过程中,本产品出现故障或损坏,EIZO 和经销商根据其独自的判断免费修理或更换该产品。
本保证期限定为(i)自本产品购买之日起的五(5)年期间或限定为到达(ii)使用本产品 3 万小时的期限(以下简称“保证期限”)。
EIZO和经销商将不向原买方或任何第三方承担本保证书所规定之外的与本产品有关的任何责任或义务。
零件停产七(7)年后,EIZO 及其经销商不再保留或保存产品的任何零件(设计零件除外)。维修显示器时,EIZO 与经销
商将使用符合我方质量控制标准的替换零件。若由于自身条件或缺少相关零件而不能修理设备,EIZO 和经销商可提供性能
相同的更换产品,而无需维修。
本保证书仅对于设有经销商的国家或地区有效。本保证书并不限定原买方的任何法律权利。
无论本保证书的任何其他条款如何规定,对于任何下列情况之一,EIZO 和经销商将不承担本保证书规定责任 :
(a) 由于运输损害、改装、改动、滥用、误用、意外事故、错误安装、灾害、维护不善和 / 或由除 EIZO 和经销商以外的
第三方进行不适当的修理造成本产品的任何故障。
(b) 由于可能发生的技术变更和 / 或调整造成本产品的任何不兼容性。
(c) 传感器的任何劣化。
(d) 由于诸如液晶显示屏(LCD)和 / 或背灯等消耗品部件的老化造成的任何显示性能低劣(如亮度变化、亮度均一性变化、
色彩变化、色彩均一性变化、如烧伤像素等像素缺陷)。
(e) 因外部设备造成本产品的任何故障。
(f) 因本产品的原序号被改变或消除造成本产品的任何故障。
(g) 本产品的任何正常老化,尤其是消耗品、附件和 / 或附加装置(如按钮、旋转部件、电缆、用户手册等)、以及
(h) 本产品表面包括液晶显示屏(LCD)表面的任何变形、变色和 / 翘曲。
为了获得本保证书规定的服务,原买方必须使用原包装或其他具有同等保护程度的适当包装将本产品运送到当地的经销商,
并且预付运费,承担运输中的损坏和 / 或损失的风险。要求提供本保证书规定的服务时,原买方必须提交购买本产品和标
明此购买日期的证明。
按本保证书规定进行了更换和 / 或修理的任何产品的保证期限,将在原保证期限结束时终止。
在返回给 EIZO 和经销商进行修理后,任何产品的任何媒体或任何部件中储存的数据或其他信息发生任何损坏或损失,对
此 EIZO 和经销商将不承担责任。
对于本产品及其质量、性能、可销售性以及对于特殊用途的适合性,EIZO 和经销商不提供其他任何明示或暗示的保证。因
使用本产品或无法使用本产品或因与本产品有任何关系(无论是否根据合同)而造成 : 任何附带的、间接的、特殊的、随
之发生的或其他的损害(包括但不仅限于:利润损失、业务中断、业务信息丢失或其他任何金钱损失)以及侵权行为、过失、
严格赔偿责任或其他责任,即使已经向 EIZO 和经销商提出了发生这些损害的可能性,对此 EIZO 和经销商概不承担责任。
本免责条款还包括因第三方向原买方提出索赔而可能发生的任何责任。 本条款的本质是限定由于本有限责任保证书和 / 或
销售本产品所发生的 EIZO 和经销商的潜在责任。
68
Appendix
Recycling Information
Recycling Information
This product, when disposed of, is supposed to be collected and recycled according to your country’s
legislationtoreduceenvironmentalburden.Whenyoudisposeofthisproduct,pleasecontactadistributoror
anaffiliateinyourcountry.
ThecontactaddresseesarelistedontheEIZOwebsitebelow.
http://www.eizoglobal.com
ForrecyclinginformationforcustomersinSwitzerland,pleaserefertothefollowingwebsite.
http://www.swico.ch
Informationen zum Thema Recycling
Dieses Produkt muss gemäß den Vorschriften Ihres Landes zur Entlastung der Umwelt recyclet werden.
Wenden Sie sich beider Entsorgung dieses Produkts aneinen Verteileroder eineTochtergesellschaft in
IhremLand.
DieAdressenzurKontaktaufnahmesindaufderuntenangegebenenWebsitevonEIZOaufgeführt.
http://www.eizoglobal.com
KundeninderSchweizentnehmenInformationenzumRecyclingderfolgendenWebsite:
http://www.swico.ch
Informations sur le recyclage
Ceproduitdoitêtrejetéauxpointsdecollecteprévusàceteffetetrecycléconformémentàlalégislationde
votrepays,afinderéduirel’impactsurl’environnement.Lorsquevousjetezceproduit,veuillezcontacterun
distributeurouunesociétéaffiliéedevotrepays.
LesadressesdesdistributeurssontrépertoriéessurlesiteWebEIZOci-dessous.
http://www.eizoglobal.com
Pour les clients en Suisse, veuillez consulter le site Web suivant afin d’obtenir des informations sur le
recyclage.
http://www.swico.ch
Información sobre reciclaje
Este producto debe desecharse y reciclarse según la legislación del país para reducir el impacto
medioambiental.Cuandodeseedeshacersedeesteproducto,póngaseencontactoconundistribuidoro
unafilialdesupaís.
EncontrarálasdireccionesdecontactoenelsitiowebdeEIZOqueseindicaacontinuación.
http://www.eizoglobal.com
Informazioni sul riciclaggio
Perlosmaltimentoeilriciclaggiodelpresenteprodotto,attenersiallenormativevigentinelpropriopaeseper
ridurrel’impattoambientale.Perlosmaltimento,rivolgersiadundistributoreounaffiliatopresentinelproprio
paese.
GliindirizzisonoelencatinelsitoWebEIZOriportatodiseguito.
http://www.eizoglobal.com
PerinformazionisulriciclaggiopericlientiinSvizzera,consultareilsitoWebriportatodiseguito.
http://www.swico.ch
Återvinningsinformation
När denna produkt kasseras ska den hanteras och återvinnas enligt landets föreskrifter för att reducera
miljöpåverkan.Närdukasserarproduktenskadukontaktaendistributörellerrepresentantidittland.
KontaktadressernalistaspåEIZO-webbplatsennedan.
http://www.eizoglobal.com
Appendix
69
Πληροφορίες ανακύκλωσης
Τοπροϊόναυτό,όταναπορρίπτεται,πρέπεινασυλλέγεταικαιναανακυκλώνεταισύμφωναμετηνομοθεσία
τηςχώραςσαςέτσιώστεναμηνεπιβαρύνειτοπεριβάλλον.Γιανααπορρίψετετοπροϊόν,επικοινωνήστεμε
έναναντιπρόσωποήμιαθυγατρικήεταιρείαστηχώρασας.
ΟιδιευθύνσειςεπικοινωνίαςαναγράφονταιστηντοποθεσίαwebτηςEIZOπαρακάτω.
http://www.eizoglobal.com
Сведения по утилизации
По истечении срока службы данного продукта его следует принести на сборный пункт и
утилизировать в соответствии с действующими предписаниями в вашей стране, чтобы уменьшить
вредное воздействие на окружающую среду. Прежде чем выбросить данный продукт, обратитесь к
дистрибьюторуиливместноепредставительствокомпанииввашейстране.
Контактныеадресаможнонайтинавеб-узлеEIZO.
http://www.eizoglobal.com
Informatie over recycling
Wanneeruditproductwiltweggooien,moethetuitmilieu-overwegingenwordenverzameldengerecycled
volgens de betreffende wetgeving van uw land. Wanneer u dit product wilt weggooien, moet u contact
opnemenmeteendistributeurofeenpartnerinuwland.
DecontactadressenwordenvermeldopdevolgendeEIZO-website.
http://www.eizoglobal.com
Informação sobre reciclagem
Esteproduto,quandoodeitarfora,deveserrecolhidoerecicladodeacordocomalegislaçãodoseupaís
parareduzirapoluição.Quandodeitarforaesteproduto,contacteumdistribuidorouumafilialnoseupaís.
OsendereçosdecontactoestãolistadosnowebsitedoEIZO,abaixo.
http://www.eizoglobal.com
Oplysninger om genbrug
Dette produkt forventes ved bortskaffelse at blive indsamlet og genbrugt i overensstemmelse med
lovgivningen i dit land for at reducere belastningen af miljøet. Når du bortskaffer denne produkt, skal du
kontakteendistributørellerettilknyttetselskabiditland.
AdressernepåkontaktpersonerneerangivetpåEIZO’swebstednedenfor.
http://www.eizoglobal.com
Kierrätystä koskevia tietoja
Tuote tulee hävittää kierrättämällä maan lainsäädännön mukaisesti ympäristön kuormittumisen
vähentämiseksi.Kunhävitättuotteen,otayhteyttäjälleenmyyjääntaitytäryhtiöönmaassasi.
YhteystiedotlöytyvätEIZOnInternet-sivustolta.
http://www.eizoglobal.com
Wykorzystanie surowców wtórnych
Tenproduktpozużyciupowinienbyćzbieranyiprzetwarzanyzgodniezkrajowymiprzepisamidotyczącymi
ochrony środowiska. Wyrzucając ten produkt, należy skontaktować się z lokalnym dystrybutorem lub
partnerem.AdresykontaktowemożnaznaleźćwewskazanejponiżejwitrynieinternetowejfirmyEIZO.
http://www.eizoglobal.com
70
Appendix
Informace o recyklaci
Při likvidaci produktu musí být produkt vyzvednut a recyklován podle zákonů příslušné země, aby
nedocházelo k zatěžování životního prostředí. Zbavujete-li se produktu, kontaktujte distributora nebo
pobočkuvesvézemi.KontaktníadresyjsouuvedenynanásledujícíwebovéstráncespolečnostiEIZO.
http://www.eizoglobal.com
Ringlussevõtu alane teave
Keskkonnakoormusevähendamisekstulekskasutatudtootedkokkukogudajavõttaringlussevastavaltteie
riigiseadustele.Kuikõrvaldatekäesolevatoote,võtkepalunühendustturustajavõifiliaaligaomariigis.
KontaktisikudontoodudEIZOveebileheljärgmiselaadressil:
http://www.eizoglobal.com
Újrahasznosítási információ
Jelenterméket,amikoreldobjuk,azilletőországtörvényeialapjánkellösszegyűjteniésújrahasznosítani,
hogy csökkentsük a környezet terhelését.Amikor ezt a terméket eldobja, kérjük lépjen kapcsolatba egy
országonbelüliforgalmazóvalvagytársvállalkozással.
AkapcsolatcímeiazEIZOalábbiweboldalántalálhatókfelsorolva:
http://www.eizoglobal.com
Podatki o recikliranju
Ob koncu uporabe odslužen izdelek izročite na zbirno mesto za recikliranje v skladu z okoljevarstveno
zakonodajo vaše države. Prosimo, da se pri odstranjevanju izdelka obrnete na lokalnega distributerja ali
podružnico.
KontaktninaslovisoobjavljeninaspodajnavedenihspletnihstranehEIZO:
http://www.eizoglobal.com
Informácie o recyklácii
Prilikvidáciimusíbyťtentovýrobokrecyklovanývsúladeslegislatívouvašejkrajiny,abysaznížilozaťaženie
životnéhoprostredia.Keďsachcetezbaviťtohtovýrobku,kontaktujteprosímdistribútoraalebopobočkuvo
vašejkrajine.
ZoznamkontaktnýchadriesjeuvedenýnanasledovnejwebovejstránkefirmyEIZO:
http://www.eizoglobal.com
Pārstrādes informācija
Utilizējot šo produktu, tā savākšana un pārstrāde veicama atbilstoši jūsu valsts likumdošanas prasībām
attiecībā uz slodzes uz vidi samazināšanu. Lai veiktu šī produkta utilizāciju, sazinieties ar izplatītāju vai
pārstāvniecībujūsuvalstī.
KontaktadresesirnorādītaszemākminētajāEIZOtīmekļavietnē.
http://www.eizoglobal.com
Informacija apie grąžinamąjį perdirbimą
Šalinant(išmetant)šiuosgaminiusjuosreikiasurinktiirperdirbtigrąžinamuojubūdupagaljūsųšaliesteisės
aktus, siekiant sumažinti aplinkos teršimą. Kai reikia išmesti šį gaminį, kreipkitės į jūsų šalyje veikiančią
gaminiųpardavimoatstovybęarbajosfilialą.
KontaktiniaiadresatainurodytiEIZOinternetosvetainėje.
http://www.eizoglobal.com
Appendix
71
Информация относно рециклиране
Приизхвърлянетонатозипродуктсепредлагасъбиранетоирециклиранетомусъобразнозаконитена
вашатастраназадасенамализамърсяванетонаоколнатасреда.Когатоискатедасеосвободитеот
тозипродукт,молясвържетесестърговскиямупредставителилисъссъответнитеорганиотговарящи
затовавъввашатастрана.
ДаннитезавръзкаснассаописанинаследнияИнтернетсайтнаEIZO:
http://www.eizoglobal.com
Informaţie referitoare la reciclare
Acestprodus,cânddebarasat,trebuiecolectatşireciclatconformlegislaţieiţăriirspectivecasăreducem
sarcinamediului.Cândsedebaraseazădeacestprodus,vărugămsăcontactaţiundistribuitorsauunafiliat
alţăriirespective.
AdreseledecontactlegăsiţipepaginadewebalEIZO:
http://www.eizoglobal.com
http://www.eizoglobal.com
Geri Dönüşüm Bilgisi
Buürünün,atılacağızaman,ülkenizinçevrekirliliğininazaltılmasıkonusundakimevzuatınagöretoplanması
veyenidendeğerlendirilmesigerekmektedir.Ürünüatacağınızzamanlütfenülkenizdekibirdistribütörveya
ilgilikuruluşlatemasageçiniz.
İrtibatadresleriaşağıdakiEIZOwebsitesindeverilmiştir.
http://www.eizoglobal.com
72
Appendix
03V23988J1
UM-CX240
Copyright © 2012-2017 EIZO Corporation. All rights reserved.
9th Edition-July, 2017
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising