Eizo | CS2420 | User manual | Eizo CS2420 User Manual

Eizo CS2420 User Manual
User’s Manual
Color Management LCD Monitor
Important
Please read PRECAUTIONS, this User’s Manual, and the Setup Guide (separate volume) carefully to familiarize yourself
with safe and effective usage.
• Please refer to the Setup Guide for basic information ranging from connection of the monitor to a PC or external
device to using the monitor.
• The latest User’s Manual is available for download from our web site:
www.eizoglobal.com

Location of Caution Statement
WARNING
AVERTISSEMENT
WARNUNG
This product has been adjusted specifically for use in the region to which it was originally shipped. If operated outside this region, the product may not perform as
stated in the specifications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, or otherwise, without
the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information confidential unless prior arrangements are made pursuant to EIZO
Corporation’s receipt of said information. Although every effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specifications are subject to change without notice.
-2-
Notice for this monitor
Notice for this monitor
Aside from general purposes like creating documents, viewing multimedia content, this product is also suited to applications such as graphics creation and digital
photo processing, where accurate color reproduction is a priority.
This product has been adjusted specifically for use in the region to which it was originally shipped. If the product is used outside the region, it may not operate as
specified in the specifications.
This product may not be covered by warranty for uses other than those described in this manual.
The specifications noted in this manual are only applicable when the following are used:
· Power cords provided with the product
· Signal cables specified by us
Only use optional products manufactured or specified by us with this product.
If you place this product on a lacquer-coated desk, the color may adhere to the bottom of the stand due to the composition of the rubber. Check the desk surface
before use.
It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more after the monitor power has been turned on, and then
adjust the monitor.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and maintain a stable display.
When the screen image is changed after displaying the same image for extended periods of time, an afterimage may appear. Use the screen saver or power save
function to avoid displaying the same image for extended periods of time.
If the monitor displays continuously over a long period of time, dark smudges or burn-in may appear. To maximize the life of the monitor, we recommend the monitor
be turned off periodically.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer to “Cleaning” (page 4)).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may appear on the LCD panel, this is not a malfunction.
Percentage of effective dots: 99.9994% or higher.
-3-
Notice for this monitor
The backlight of the LCD panel has a fixed lifetime. When the screen becomes dark or begins to flicker, please contact your local EIZO representative.
Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions, such as interference patterns, etc. If pressure is continually
applied to the panel, it may deteriorate or damage your panel. (If the pressure marks remain on the panel, leave the monitor with a black or white screen. The
symptom may disappear.)
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do not attempt to brush with tissues as this may scratch the
panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may occur on the interior and exterior surfaces of the
monitor. In that case, do not turn the monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage to the monitor.
Cleaning
Attention
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or panel, and also quality deterioration of the image.
• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.
Note
• The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface.
The stains on the cabinet and panel surface can be removed by moistening part of a soft cloth with water.
To use the monitor comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according to the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
-4-
Contents
Contents
Notice for this monitor.................................................................................. 3
3-2.
Setting Menu Functions...........................................................................18
●● Color...........................................................................................................18
Cleaning..................................................................................................................4
●● Signal Settings...........................................................................................21
To use the monitor comfortably...........................................................................4
●● Preferences................................................................................................24
Contents......................................................................................................... 5
●● Languages..................................................................................................26
Chapter 1 Introduction................................................................................. 7
1-1.
Features......................................................................................................7
1-2.
Controls and Functions.............................................................................9
●● Front.............................................................................................................9
●● Rear............................................................................................................10
●● Information.................................................................................................26
Chapter 4 Administrator Settings............................................................. 27
4-1.
Basic Operation of the “Administrator Settings” menu.......................27
4-2.
“Administrator Settings” Menu Functions.............................................28
Chapter 5 Troubleshooting........................................................................ 29
Supported Resolutions............................................................................11
5-1.
No picture..................................................................................................29
●● When using digital signal input (DVI-D, DisplayPort, HDMI: PC signal).....11
5-2.
Imaging problems....................................................................................30
5-3.
Other problems.........................................................................................31
1-3.
●● When using digital signal input (HDMI: Video signal*2)..............................12
1-4.
Changing the PC Display Settings..........................................................12
●● Windows 10................................................................................................12
Chapter 6 Reference................................................................................... 32
●● Windows 8.1 / Windows 7........................................................................13
●● macOS.......................................................................................................13
Chapter 2 Basic Adjustments/Settings..................................................... 14
2-1.
Switch Operation Method........................................................................14
2-2.
Switching Input Signals...........................................................................15
2-3.
Switching the display mode (color mode).............................................16
●● Display Modes............................................................................................16
Removing the Stand.................................................................................32
6-2.
Attaching the Optional Arm.....................................................................33
6-3.
Detaching/Attaching Stand Base............................................................36
6-4.
Attaching/Detaching Cable Holder.........................................................39
6-5.
Connecting Multiple External Devices...................................................41
6-6.
Making Use of USB (Universal Serial Bus)............................................42
●● Required System Environment...................................................................42
Chapter 3 Advanced Adjustments/Settings............................................. 17
3-1.
6-1.
●● Connection Procedure (Setup of USB Function)........................................43
6-7.
Basic Operation of the Setting menu.....................................................17
-5-
Specifications...........................................................................................44
Contents
●● Dimensions.................................................................................................46
●● Main Default Settings.................................................................................47
●● Accessories................................................................................................47
Chapter 7 Glossary..................................................................................... 48
Appendix...................................................................................................... 50
Trademark.............................................................................................................50
License.................................................................................................................50
FCC Declaration of Conformity..........................................................................51
-6-
Chapter 1 Introduction
Chapter 1 Introduction
Thank you very much for choosing an EIZO color LCD monitor.
1-1. Features
•
•
•
•
•
•
24.0″ widescreen
Wide color gamut display (Adobe® RGB coverage: 99%)
Supports a resolution of 1920 × 1200
IPS panel with 89˚ horizontal and vertical wide viewing angles
Frame synchronization mode supported (23.75 – 30.5 Hz, 47.5 – 61.0 Hz)
Support for three digital signal inputs (DVI-D × 1, HDMI × 1, DisplayPort × 1)
-- DisplayPort connector (applicable to 8 bit and 10 bit)*1
-- HDMI connector (applicable to 8 bit, 10 bit, and 12 bit)*1,*2
Can handle PC signals in HDMI input
*1 Not applicable to audio signals.
*2 10 bit and 12 bit are supported only when using HDMI-Video. The maximum screen display is 10 bits.
• Color mode function
Reproduces a color temperature, gamma, and gamut compliant with the following standards.
-- Adobe® RGB / sRGB
See “Chapter 3 Advanced Adjustments/Settings” (page 17)
• Stand with wide range of movement
The monitor can be adjusted to a position where it provides you with a comfortable and less tiring work environment.
(Tilt: up 35˚/down 5˚, Swivel: 344˚, Adjustable height: 145 mm (Tilt: 35°), 155 mm (Tilt: 0°))
• Supports portrait format
• Compatible with Color Management Software “ColorNavigator 7”, which enables you to calibrate monitor characteristics and generate color profiles
• Equipped with a USB Hub function that supports USB 3.0
Achieves high-speed data transfers of up to 5 Gbps, which enables transfers of large amounts of data to and from USB-connected devices in a short amount time.
Also, the “CHARGE” USB downstream port supports quick charging, so you can recharge your smartphone or tablet in a short period of time.
See “6-5. Connecting Multiple External Devices” (page 41) and “USB CHARGE Port” (page 25)
• Displays HDCP (High Bandwidth Digital Protection) protected contents
-7-
Chapter 1 Introduction
Note
• This monitor supports portrait format. When using the screen in a portrait position, you can change the orientation of the Setting menu. (see “Menu Rotation” (page 24))
• When using the monitor screen in a portrait position, the graphics board supporting portrait display is required. When placing the monitor in a portrait position, the settings of
your graphics board need to be changed. Refer to the User’s Manual of the graphics board for details.
-8-
Chapter 1 Introduction
1-2. Controls and Functions
●●Front
Setting menu *1
2
1
1. Operation switches
2. Power switch
Displays menus. Operate the switches according to the operation guide.
The switch indicator is lit white when you turn the power on.
Turns the power on or off.
The switch indicator is lit when you turn the power on. The indicator color differs depending on the monitor's operation status.
White: Operating
Orange: Power saving mode
OFF: Power off
*1 See “3-1. Basic Operation of the Setting menu” (page 17) for how to use.
-9-
Chapter 1 Introduction
●●Rear
8
7
10
9
3
4
11
5
3. Main power switch
Turns the main power on ( ) or off (
4. Power connector
5. Input signal connectors
6. USB upstream port
7. USB downstream port
Connects the power cord.
8. Handle
6
).
Left: DVI-D connector / Center: HDMI connector / Right: DisplayPort connector
Connects to the USB cable when using software that requires a USB connection, or when using the USB Hub function (page 42).
Connects to a peripheral USB device.
The “CHARGE” port
supports quick recharging (page 25).
This handle is used for transportation.
Attention
• Firmly grasp and hold the monitor by the bottom while grabbing the handle, and carefully convey the monitor so as not to drop it.
Do not hold the sensor section on the front side of the monitor.
9. Security lock slot
10. Stand *2
Complies with Kensington’s MicroSaver security system.
Adjusts the height and angle (tilt and swivel) of the monitor.
Attention
• Do not hold the sensor section on the front side of the monitor.
*3
Covers the monitor cables.
11. Cable holder
*2 An optional arm (or an optional stand) can be attached by removing the stand section (see “6-1. Removing the Stand” (page 32)).
*3 For details on mounting the cable holder, see “6-4. Attaching/Detaching Cable Holder” (page 39).
- 10 -
Chapter 1 Introduction
1-3. Supported Resolutions
The monitor supports the following resolutions.
●●When using digital signal input (DVI-D, DisplayPort, HDMI: PC signal)
Resolution
Vertical scan frequency
640 x 480
60 Hz
720 x 400
70 Hz
800 x 600
60 Hz
1024 x 768
60 Hz
1280 x 960
60 Hz
1280 x 1024
60 Hz
1600 x 1200
60 Hz
1680 x 1050
60 Hz
1920 x 1080
60 Hz
1920 x 1200
*1
60 Hz
*1 Recommended resolution
- 11 -
Chapter 1 Introduction
●●When using digital signal input (HDMI: Video signal*2)
Resolution
Vertical scan frequency
24Hz
25Hz
30Hz
50Hz
60Hz
640 x 480
-
-
-
-
√
720 × 480 (480i)
-
-
-
-
√
720 × 480 (480p)
-
-
-
-
√
720 × 576 (576i)
-
-
-
√
-
720 × 576 (576p)
-
-
-
√
-
1280 × 720 (720p)
-
-
-
√
√
1920 × 1080 (1080i)
-
-
-
√
√
1920 × 1080 (1080p)
√
√
√
√
√
*2 To display video signals by HDMI signal input, you must change the monitor settings beforehand.
1-4. Changing the PC Display Settings
If the screen is not properly displayed after connecting the monitor to a PC, follow the procedure below to change the PC display settings.
●●Windows 10
1. Right-click anywhere on the desktop except for on icons to display the menu.
2. From the displayed menu, click “Display settings” to display the “Settings” screen.
3. If there are multiple monitors including the notebook PC screen connected to the computer, select “Extend these displays” from the “Multiple displays”
menu, and click “Keep changes” in the confirmation screen. After changing the settings, select the monitor from the “Select and arrange display” menu.
4. By checking the option “Make this my main display” from the “Multiple displays” menu, the display of the monitor will be corrected.
5. Confirm that the monitor’s recommended resolution is set in the “Resolution” menu (the term (Recommended) should be displayed after the resolution).
6. To change the size of letters and icons, select the preferred magnification level from the scaling (%) menu.
7. When after changing these settings a message is displayed that prompts you to sign out, sign out once and then sign in again.
- 12 -
Chapter 1 Introduction
●●Windows 8.1 / Windows 7
* For Windows 8.1, click the “Desktop” tile on the Start Screen to display the desktop.
1. Right-click anywhere on the desktop except for on icons to display the menu.
2. From the displayed menu, click “Screen resolution” to display the settings screen.
3. If there are multiple monitors including the notebook PC screen connected to the computer, select “Extend these displays” from the “Multiple displays”
menu, and click “Apply”. In the confirmation screen, click “Keep changes”.
4. Select the monitor from the “Display” menu, check the option “Make this my main display”, and click “Apply”. The display of the monitor will be corrected.
5. Confirm that the monitor’s recommended resolution is set in the “Resolution” menu (the term (Recommended) should be displayed after the resolution).
6. To change the size of letters and icons, click “Make text and other items larger or smaller”, select the preferred size from the settings screen, and click “Apply”.
7. When after changing settings a message is displayed that prompts you to sign out or log off, sign out or log off once and then sign in or log on again.
●●macOS
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” panel is displayed, click “Displays”.
3. If there are multiple monitors including the notebook PC screen connected to the computer, open the “Arrangement” tab and confirm that “Mirror displays”
is not selected. If it is selected, clear it.
4. Select the “Display” tab, and confirm that “Default for display” of “Resolution” is selected. If it is not selected, select it. This sets the correct resolution.
Close the “System Preferences” menu. If there are multiple monitors including the notebook PC screen connected to the computer, change the settings for
each monitor by using “Display”.
5. To select a different resolution, select “Scaled”, select a resolution from the resolution list (displayed in list or icon format), and close the panel.
- 13 -
Chapter 2 Basic Adjustments/Settings
Chapter 2 Basic Adjustments/Settings
This chapter describes the basic functions that can be adjusted and set by touching the switches on the front of the monitor.
For advanced adjustment and setting procedures using the Setting menu, see “Chapter 3 Advanced Adjustments/Settings” (page 17).
2-1. Switch Operation Method
1. Displaying the operation guide
1. Touch any switch (except
).
The operation guide appears on the screen.
2. Adjusting/setting
1. Touch a switch for adjustment/setting.
The Adjustment/Setting menu appears.
2. Use the switches to adjust/set the selected item, and then select
3. Exiting
1. Select
or
to confirm.
to exit the menu.
2. When no menu is displayed, the operation guide will automatically disappear after a few seconds if no switches are operated.
Note
• The contents of the guide will differ depending on the selected menu or status.
- 14 -
Chapter 2 Basic Adjustments/Settings
2-2. Switching Input Signals
When a monitor has multiple signal inputs, the signal to display on-screen can be changed.
When the input signal is switched, the connector name of the displayed signal appears at the bottom right of the screen.
- 15 -
Chapter 2 Basic Adjustments/Settings
2-3. Switching the display mode (color mode)
This function allows easy selection of a display mode according to monitor application.
●●Display Modes
Color Mode
Standard Mode
Custom
Adobe®RGB
sRGB
Advanced Mode (CAL mode)
CAL1
CAL2
CAL3
Purpose
Adjust color using the Color Management Software “ColorNavigator 7” or the monitor’s Setting menu.
Select for configuring color settings according to your preference.
Suitable for color matching with Adobe®RGB compatible peripherals.
Suitable for color matching with sRGB compatible peripherals.
Adjusts the monitor’s color using the “ColorNavigator 7” color management software.
Displays the screen adjusted by ColorNavigator 7.
Note
• The Setting menu and the Mode names cannot be displayed at the same time.
• You can disable specific mode selections. For more information, see “Mode Skip” (page 25).
• In the default settings, available Advanced Mode (CAL modes) differ depending on each input signal.
-- CAL1 : DVI
-- CAL2 : DisplayPort
-- CAL3 : HDMI
- 16 -
Chapter 3 Advanced Adjustments/Settings
Chapter 3 Advanced Adjustments/Settings
This chapter describes the advanced monitor adjustment and setting procedures using the Setting menu.
For the basic adjustment/setting functions using the switches on the front of the monitor, see “Chapter 2 Basic Adjustments/Settings” (page 14).
3-1. Basic Operation of the Setting menu
1. Menu display
1. Touch any switch (except
2. Choose an item to adjust/set with
.
).
The Adjustment/Setting menu appears.
The operation guide appears.
2. Select
, and then press
.
The Setting menu appears.
3. Adjust/set the selected item with
.
, and then select
The Sub menu appears.
Selecting
during adjustment/setting will cancel the adjustment/setting
and restore the state prior to making changes.
2.
3. Exiting
Adjusting/setting
1. Choose a menu to adjust/set with
.
1. Select
, and then select
.
The Setting menu appears.
2. Select
The Sub menu appears.
.
The Setting menu exits.
Note
• The contents of the guide will differ depending on the selected menu or status.
- 17 -
Chapter 3 Advanced Adjustments/Settings
3-2. Setting Menu Functions
●●Color
When the screen is displayed in Standard Mode (Custom / Adobe®RGB / sRGB), you can adjust the color settings of each color mode according to your
preference.
Attention
• The same image may be seen in different colors on multiple monitors due to their monitor-specific characteristics. Make fine color adjustment visually when matching colors
on multiple monitors.
Note
• Use the values shown in “K” and “%” as a guide only.
Function
Color Mode
Brightness
Temperature
Adjustable range
Description
Note
Custom
Adobe®RGB
sRGB
CAL1
CAL2
CAL3
0% to 100%
Select the desired mode according to the monitor application.
• For more information on how to switch modes,
see “2-3. Switching the display mode (color
mode)” (page 16).
The screen brightness is adjusted by changing the brightness of
the backlight (light source from the LCD back panel).
Native
4000 K to 10000 K
Adobe®RGB
sRGB
The color temperature can be adjusted.
The color temperature is used to express the hue of “White” or
“Black” by a numerical value. The value is expressed in degrees “K”
(Kelvin).
The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like the flame temperature.
• If the entered value cannot be set, the value
will appear in magenta. In such a case,
change the value.
• When you select “Native”, the original color
of the monitor (Gain: 100% for each RGB)
is displayed.
• “Gain” allows you to perform more advanced
adjustment. When gain is changed, the color
temperature is changed to “User”.
• The gain preset values are set for each color
temperature setting value.
Specify color temperature in units of 100 K, or select a color
­temperature that complies with each standard.
- 18 -
Chapter 3 Advanced Adjustments/Settings
Function
Gamma
Adjustable range
1.6 to 2.7
Adobe®RGB
sRGB
Description
Note
Adjust the gamma.
The brightness of the monitor varies depending on the input
signal, however, the variation rate is not simply proportional to the
input signal. The control performed to keep the balance between
the input signal and the brightness of the monitor is called
“Gamma correction”.
You can set the gamma, or select the gamma curve defined by
each standard.
Color Gamut
Advanced Settings
Native
Adobe®RGB
sRGB
Set the color reproduction area (color gamut).
“Color gamut” is the range of colors that devices such as monitors,
digital cameras and printers can represent. Multiple standards are
defined.
Hue
-100 to 100
Adjust the hue.
Saturation
-100 to 100
Adjust the color saturation.
- 19 -
• When you select “Native”, the original color
gamut of the monitor is displayed.
• The method of displaying colors outside the
monitor’s displayable range within the defined
color gamut can be set. For more information,
see “Clipping” (page 20).
• Using this function may make some color
gradations unavailable for display.
• Using this function may make some color
gradations unavailable for display.
• The minimum value (-100) changes the
screen to monochrome.
Chapter 3 Advanced Adjustments/Settings
Function
Advanced Settings
Clipping
Adjustable range
On
Off
Description
Note
The method of displaying colors outside the monitor’s displayable
range within the color gamut specified in accordance with “Color
Gamut” (page 19) can be set.
• The diagrams on the left are conceptual
diagrams, and do not display the actual color
gamut of the monitor.
• This setting will be disabled if “Native” is
selected at “Color Gamut” (page 19).
• “On”
The range of colors that are
displayable on the monitor
will be accurately displayed in
accordance with the standard.
Colors outside the displayable
range will be saturated.
• “Off”
Displays colors with priority on
the color gradation rather than
the color accuracy. The vertices of the color gamut defined
in the standard move to a
range that can be displayed
by the monitor. This allows the
closest colors displayable by
the monitor to be displayed.
Color gamut displayable by the monitor
Color gamut defined by standard
Color gamut displayed on screen
Reset
Gain
0% to 100%
The brightness of each color component red, green, and blue is
called Gain. The hue of “white” can be changed by adjusting the
gain.
6 Colors
-100 to 100
The hue, saturation and lightness can each be adjusted for the
colors Magenta, Red, Yellow, Green, Cyan, and Blue.
Resets any color adjustments for the currently selected color
mode back to the default settings.
-
- 20 -
• Using this function may make some color
gradations unavailable for display.
• The gain value changes according to the color
temperature.
• When gain is changed, the color temperature
is changed to “User”.
-
Chapter 3 Advanced Adjustments/Settings
●●Signal Settings
The signal settings are used to configure advanced settings for input signals, such as the screen display size and color format.
- 21 -
Chapter 3 Advanced Adjustments/Settings
Input Signal
Function
Picture Expansion
(The setting range of each ­function
differs depending
on the input signal.)
√: Settable -: Not settable
DVI
DisplayPort
HDMI
√
√
√
Adjustable
range
Auto*1
Full Screen
Aspect Ratio
Dot by Dot
Description
(Fixed
RGB)
√
• Example settings
The screen size of the monitor display can be changed.
• “Auto”
The monitor automatically changes the screen size
­according to the resolution information and aspect ratio
information sent from the input signal.
• “Full Screen”
Displays an image in full screen. Images are distorted in
some cases because the vertical rate is not equal to the
horizontal rate.
When using video signal (480p/i, 576p/i) input, the image
will be displayed in full screen while maintaining the 16:9
aspect ratio.
• “Aspect Ratio”
Displays an image in full screen. However, since aspect
ratios are maintained, part of an image may not be visible
in horizontal or vertical direction.
When using video signal (480p/i, 576p/i) input, the image
will be displayed in full screen while maintaining the 4:3
aspect ratio.
• “Dot by Dot”
Displays the image at the set resolution or at the size
specified by the input signal.
Auto*2
The color space of the input signal can be specified.
Try changing this setting if colors are not displayed correctly.
YUV 4:2:2
YUV 4:4:4
RGB
*1 Only enabled when input signal information for automatically determining the setting is detected during HDMI input
*2 Only enabled when input signal information for automatically determining the setting is detected
Input Color Format
Note
√
- 22 -
--Full Screen
--Aspect Ratio
--Dot by Dot (input signal)
-
Chapter 3 Advanced Adjustments/Settings
Input Signal
Function
(The setting range of each ­function
differs depending
on the input signal.)
√: Settable -: Not settable
Adjustable
range
Description
DVI
DisplayPort
HDMI
Input Range
√
√
√
Auto*3
Full
Limited
(109% White)
Limited
Depending on the external device, the black and white levels in the video signal output to the monitor may be restricted. If
the signal is displayed on the monitor in its restricted form, the
blacks will be faint, the whites dull, and contrast will be reduced. The brightness range of such signals can be extended
to match the actual contrast ratio of the monitor.
• “Auto”
The monitor automatically recognizes the brightness
range of input signals and displays images appropriately.
• “Full”
The input signal brightness range is not extended.
• “Limited (109% White)”
The brightness range of the input signal is extended from
64 - 1019 to 0 - 1023 for display.
• “Limited”
The brightness range of the input signal is extended from
64 - 940 to 0 - 1023 for display.
­ eduction
Noise R
-
-
√
On
Off
The small noises that occur in dark areas of an image are
reduced. Use this function to reduce noise and roughness in
images.
*3 Only enabled during DisplayPort input or HDMI input
- 23 -
Note
• Using the Noise Reduction
function may lead to deterioration of fine images.
Chapter 3 Advanced Adjustments/Settings
●●Preferences
The monitor’s settings can be configured to suit the usage environment or personal preference.
Function
Auto Input Detection
Adjustable range
On
Off
Description
Note
When this function is set to “On”, the monitor automatically recognizes the connector through which signals are input, so that
the screen can be displayed. When an external device enters the
power saving mode, the monitor automatically displays another
signal.
• When the main power is turned on/off, the
signal is detected automatically regardless of
the setting for this function.
When set to “Off”, the monitor displays the signal from the selected connector regardless of whether a signal is input or not. In this
case, select the input signal to display using the operation switch
(
) on the front of the monitor.
Menu Rotation
0°
90°
This function allows you to change the orientation of the Setting
menu to align with the installation orientation.
- 24 -
• Be sure that the cables are correctly
­connected.
• When using the monitor screen in a portrait
position, the graphics board supporting
portrait display is required. When placing the
monitor in a portrait position, settings of your
graphics board need to be changed. Refer to
the User’s Manual of the graphics board for
details. Also, visit the EIZO website
(www.eizoglobal.com).
• When using the monitor in a portrait position,
rotate the monitor after pulling up the screen to
the uppermost position of the stand and setting
the screen tilted upward.
Chapter 3 Advanced Adjustments/Settings
Function
Adjustable range
Description
USB CHARGE Port
Normal
Charging Only
The “CHARGE” USB downstream port of the monitor supports
USB 3.0 quick charging. By changing this setting to “Charging
Only”, devices connected to the “CHARGE” port can be charged
more quickly than when using the “Normal” setting.
Power Save
On
Off
This function allows you to set the monitor to the power saving
mode, depending on the state of an external device connected
to it.
The monitor changes to power saving mode about 15 seconds
after signal input ceases to be detected. When the monitor has
shifted to power saving mode, images are not displayed on the
screen.
Note
• Make sure to complete any communication
between connected USB devices and the PC
before switching this setting. When the setting
is switched, all communication will be temporarily interrupted.
• Devices that are connected to the “CHARGE”
port must support quick charging.
• When “Charging Only” is set, data communications between the PC and connected devices
via the “CHARGE” port are not possible, and
therefore, connected devices will not work.
• When “Charging Only” is set, charging is possible even when the monitor and PC are not
connected by USB cable.
• At the time of shifting to power saving mode,
a message that indicates the transition is
displayed 5 seconds in advance.
• When not using the monitor, you can turn off
the main power supply so that the power is cut
completely.
• When the monitor is in power saving mode,
devices connected to the USB downstream
port will still work. Therefore, power consumption of the monitor varies even in the power
saving mode, depending on the connected
devices.
• Exiting power saving mode
--If the monitor receives input, it automatically exits power
saving mode and returns to the normal display mode.
Indicator
Off / 1 to 7
Beep
Input Skip
On
Off
Skip / -
Mode Skip
Skip / -
Monitor Reset
-
The brightness of the power switch and the operation switches
when the screen is displayed can be set. (Default setting: 4)
You can turn off the beep that sounds each time a switch is
­operated.
This function allows skipping of input signals that will not be used
when the input signals are switched.
This function allows skipping of modes that will not be used when
selecting modes. Please use this function if display modes are
limited, or if you want to prevent randomly changing the display
status.
Restore all settings to their default values except for the following
settings.
• Settings in the “Administrator Settings” menu
- 25 -
• Set at least one mode to “-”.
• Not all modes can be set to “Skip”.
• In the default settings, available Advanced
modes (CAL modes) differ depending on each
input signal.
• Regarding the default setting, see
“Main Default Settings” (page 47).
Chapter 3 Advanced Adjustments/Settings
●●Languages
The display language for menus and messages can be selected.
Adjustable range
English, Deutsch, Français, Español, Italiano, Svenska, Japanese, Simplified Chinese, Traditional Chinese
●●Information
You can check the monitor information (model name, serial number, firmware version, usage time, ColorNavigator license status, resolution, input signal, etc.).
Example:
- 26 -
Chapter 4 Administrator Settings
Chapter 4 Administrator Settings
This chapter describes how to configure monitor operation using the “Administrator Settings” menu.
This menu is for administrators. Configuration on this menu is not required for normal monitor use.
4-1. Basic Operation of the “Administrator Settings” menu
1. Menu display
1. Touch
2. Settings
to turn off the monitor.
2. While touching the leftmost switch, touch
to turn on the monitor.
1. Choose an item to set with
for more than 2 seconds
, and then select
The Adjustment/Setting menu appears.
2. Set the item with
, and then select
.
The “Administrator Settings” menu appears.
3. Applying and exiting
The “Administrator Settings” menu appears.
1. Select “Apply”, and then select
.
The settings are confirmed and the “Administrator Settings” menu quits.
- 27 -
.
Chapter 4 Administrator Settings
4-2. “Administrator Settings” Menu Functions
Function
On-Screen Logo
Adjustable Range
On
Off
Key Lock
Off
Menu
All
DP Power Save
On
Off
DUE Priority
Brightness
Uniformity
Signal Format DisplayPort
RGB
RGB/YUV
Video
PC
HDMI
Description
Note
When the monitor is turned on, the EIZO logo appears on the screen. When this function is set to “Off”, the EIZO logo does not appear.
In order to prevent changes to settings, the operation switches on the front of the monitor can be locked.
• “Off” (Default setting)
Enable all switches.
• “Menu”
Lock the
switch.
• “All”
Lock all switches except the power switch.
If the PC is connected to the DisplayPort connector, and when the
power is turned on or off or when the monitor recovers from power
saving mode, window or icon positions may be shifted. If that occurs,
set this function to “Off”.
• When changing the DUE setting, the
This product is equipped with a Digital Uniformity Equalizer (DUE)
monitor whose display is adjusted must be
function that reduces display unevenness. This DUE setting can be
re-calibrated. Perform the target calibrachanged.
tion again using ColorNavigator 7. For de• “Brightness”
tails, refer to the ColorNavigator 7 User's
Prioritizes high brightness and high contrast.
Manual.
• “Uniformity”
Prioritizes reduction of display unevenness.
You can switch the signal type that the monitor can display.
To display video signals when using HDMI signal input, set to “Video”.
- 28 -
Chapter 5 Troubleshooting
Chapter 5 Troubleshooting
If a problem still remains after applying the suggested remedies, contact your local EIZO representative.
5-1. No picture
Problem
1. No picture
• Power indicator does not light up.
• Power indicator is lighting white.
• Power indicator is lighting orange.
• Power indicator is flashing orange and white.
2. The message below appears.
• This message appears when no signal is input.
Example:
• The message shows that the input signal is out
of the specified frequency range.
Example:
Possible cause and remedy
•
•
•
•
•
•
•
•
•
•
Check whether the power cord is connected properly.
Turn on the main power switch on the rear side of the monitor.
Touch .
Turn off the main power on the rear side of the monitor, and then turn it on again a few minutes later.
Increase “Brightness” and/or “Gain” in the Setting menu. (See “Color” (page 18))
Switch the input signal.
Move the mouse or press any key on the keyboard.
Check whether the PC is turned on.
Turn off the main power on the rear side of the monitor, and then turn it on again.
This problem may occur when a PC is connected via the DisplayPort connector. Connect with the signal cable specified
by EIZO, turn off the monitor, and then turn it on again.
This message appears when the signal is not input correctly even though the monitor is functioning properly.
•
•
•
•
•
The message shown left may appear, because some PCs do not output the signal immediately after power-on.
Check whether the PC is turned on.
Check whether the signal cable is connected properly.
Switch the input signal.
Turn off the main power on the rear side of the monitor, and then turn it on again.
• Check whether the PC is configured to meet the resolution and vertical scan frequency requirements of the monitor
(see “1-3. Supported Resolutions” (page 11)).
• Reboot the PC.
• Change to the appropriate setting using the graphics board's utility. Refer to the User's Manual of the graphics board for
details.
- 29 -
Chapter 5 Troubleshooting
5-2. Imaging problems
Problem
1. The screen is too bright or too dark.
2. Afterimages appear
3. Green/red/blue/white dots or defective dots
remain on the screen.
4. Interference patterns or pressure marks
remain on the screen.
5. Noise appears on the screen.
6. (DisplayPort signal input)
When you switch the power back on or
return from power save mode, windows or
icons may have shifted position.
7. (DisplayPort or HDMI input)
The color shown on the screen is not correct.
8. The image does not display on the entire
screen.
Possible cause and remedy
• Use “Brightness” in the Setting menu to adjust it (see “Information” (page 26)). (The LCD monitor backlight has a limited life span. When the screen becomes dark or begins to flicker, contact your local EIZO representative.)
• Afterimages are particular to LCD monitors. Avoid displaying the same image for a long time.
• Use the screen saver or power saving function to avoid displaying the same image for extended periods of time.
• This is due to LCD panel characteristics and not a malfunction.
• Display a white or black image over the entire screen. The symptom may disappear.
• When inputting HDCP system signals, normal images may not be displayed immediately.
• In the Setting menu, set “DP Power Save” to “Off” (see “DP Power Save” (page 28)).
• Try changing “Input Color Format” in the Setting menu (see “Input Color Format” (page 22)).
• For HDMI signal input, try changing “Signal Format” in the Setting menu (see “Signal Format” (page 28)).
• Try changing “Picture Expansion” in the Setting menu (see “Picture Expansion” (page 22)).
• For HDMI signal input, check whether “Signal Format” is set to “PC” in the Setting menu (see “Signal Format” (page
28)).
- 30 -
Chapter 5 Troubleshooting
5-3. Other problems
Problem
1. The Setting menu/Mode menu cannot be
displayed
2. The monitor connected with the USB cable
is not detected. / USB device connected to
the monitor does not work.
Possible cause and remedy
•
•
•
•
•
•
•
•
•
•
3. Audio is not output.
•
•
Check whether the operation switch lock function works (see “Key Lock” (page 28)).
Operation switches are locked when the main window of ColorNavigator 7 is displayed.
Check whether the USB cable is connected correctly (see “6-5. Connecting Multiple External Devices” (page 41)).
If a peripheral device is connected to the “CHARGE” port, try checking the “USB CHARGE Port” setting
(see “USB CHARGE Port” (page 25)). If it is set to “Charging Only”, the peripheral device will not work.
Try changing to a different USB port on the PC.
Try changing to a different USB port on the monitor.
Reboot the PC.
If the peripheral devices work correctly when the PC and peripheral devices are connected directly, contact your local
EIZO representative.
Check whether the PC and OS are USB compliant. (For USB compliance of the respective devices, consult their manufacturers.)
Depending on the USB 3.0 host controller that you are using, connected USB devices may not be recognized correctly.
Update to the latest USB 3.0 driver provided by each manufacturer, or connect the monitor to the USB 2.0 port.
Check the PC’s BIOS setting for USB when using Windows. (Refer to the manual of the PC for details.)
This monitor does not support the HDMI/DisplayPort audio signals.
- 31 -
Chapter 6 Reference
Chapter 6 Reference
6-1. Removing the Stand
The stand section of this product can be removed.
Attention
• Do not move the removed stand up and down. Doing so may result in injury or equipment damage.
• The monitor and stand are heavy. Dropping them may result in injury or equipment damage.
1. To prevent damaging the panel surface, lay the monitor with its panel surface facing down on a soft cloth spread on a
stable surface.
2. Remove the stand.
Press and hold he lock button (1), firmly grip the stand support, and then slide the stand in the direction of the base of the stand (2).
When the tab that holds the stand in place loosens, remove the stand (3).
(3)
(2)
(1)
- 32 -
Chapter 6 Reference
6-2. Attaching the Optional Arm
An optional arm (or an optional stand) can be attached by removing the stand section. Please refer to our web site for the corresponding optional arm
(or optional stand). www.eizoglobal.com
Attention
• When attaching an arm or stand, follow the instructions of their User's Manual.
• When using another manufacturer’s arm or stand, confirm the following in advance and select one conforming to the VESA standard. Use the VESA mounting screws supplied
with this product when attaching the arm or stand.
-- Clearance between screw holes: 100 mm × 100 mm
-- External dimensions of the VESA mount section of the arm or stand: 122 mm × 122 mm or less
-- Plate thickness: 2.6 mm
-- Must be strong enough to support weight of the monitor unit (excluding the stand) and attachments such as cables.
• When using an arm or stand, attach it to meet the following tilt angles of the monitor.
-- Up 45˚, down 45˚
• Connect the cables after attaching an arm or stand.
• Do not move the removed stand up and down. Doing so may result in injury or equipment damage.
• The monitor, arm, and stand are heavy. Dropping them may result in injury or equipment damage.
• When installing the monitor in portrait mode, turn the monitor screen 90˚ in clockwise direction.
- 33 -
Chapter 6 Reference
Attaching the Optional Arm (or Optional Stand)
1. Attach the arm or stand to the monitor.
Use the VESA mounting screws supplied with this product when attaching the arm or stand.
- 34 -
Chapter 6 Reference
Attaching the original stand
1. To prevent damaging the panel surface, lay the monitor with its panel surface facing down on a soft cloth spread on a
stable surface.
2. Remove the fixing screws on the optional arm (or optional stand), and detach the optional arm (or optional stand).
3. Attach the original stand.
Insert the four tabs on the stand into the square holes on the back panel (1) and slide the stand towards the upper portion of the monitor until it makes a
clicking sound (2).
(1)
(2)
Click!
- 35 -
Chapter 6 Reference
6-3. Detaching/Attaching Stand Base
Detachment procedure
The stand base that was attached during setup can be detached using the following procedures.
1. Lay the LCD monitor on a soft cloth spread over on a stable surface with the panel surface facing down.
2. Raise the lever on the bottom of the stand base.
3. Turn the stand base in the counterclockwise direction to detach it.
- 36 -
Chapter 6 Reference
Attachment procedure
The once removed the stand base can be attached to the monitor again with the following procedures.
1. Lay the LCD monitor on a soft cloth spread over on a stable surface with the panel surface facing down.
2. Attach the stand base onto the stand brace.
- 37 -
Chapter 6 Reference
3. Turn the stand base clockwise until it makes a clicking sound.
k!
Clic
- 38 -
Chapter 6 Reference
6-4. Attaching/Detaching Cable Holder
A cable holder is supplied with this product. Use the cable holder to organize the cables connected to the monitor.
Attachment procedure
1. Pass the cables through the cable holder.
2. Close the cable holder.
3. While holding the cable holder closed, insert it into the stand.
- 39 -
Chapter 6 Reference
Note
• The cable holder can be inserted either perpendicular or parallel to the stand. Change the orientation of the cable holder in line with the direction of the cables.
Detachment procedure
1. Close the cable holder.
2. While holding the cable holder closed, pull it from the stand.
- 40 -
Chapter 6 Reference
6-5. Connecting Multiple External Devices
The product allows you to connect multiple external devices and switch between them for display.
Connection
examples
• The input signal changes each time the
operation switch (
) on the front of
the monitor is touched. When the signal is
switched, the active input connector name
appears at the lower right corner of the
screen.
• This product automatically recognizes the
connector through which signals are input
and displays images on the screen accordingly. For more information, see
“Auto Input Detection” (page 24).
Digital
(DVI)
Digital
(HDMI)
Digital
(DisplayPort)
Signal cable
FD-C39
(optional)
Signal cable
HH200HS
Signal cable
PP200
DVI connector
To PC 1
Note
HDMI connector
To PC 2
- 41 -
DisplayPort connector
To PC 3
Chapter 6 Reference
6-6. Making Use of USB (Universal Serial Bus)
This monitor is equipped with a USB hub. It works as a USB hub when connected to a USB-compatible PC, allowing the connection of peripheral USB devices.
Note
• This product supports USB 3.0. When connecting peripheral devices that support USB 3.0, high-speed data communication is possible (however, only when the USB cable used
to connect the PC and peripheral device is USB 3.0 compliant).
• The “CHARGE” USB downstream port also supports quick charging. This allows you to recharge your smartphone or tablet in a short period of time. (See “USB CHARGE Port”
(page 25).)
●●Required System Environment
• A PC equipped with a USB port
• Windows 10 / Windows 8.1 / Windows 8 / Windows 7, or Mac OS X 10.7.5 or later
• EIZO USB cable (UU200SS (USB 3.0))
Attention
• This monitor may not work depending on the used PC, OS or peripheral devices. For USB compatibility of peripheral devices, contact their manufactures.
• When the monitor is in power saving mode, devices connected to the USB downstream port will still work. Therefore, power consumption of the monitor varies depending on
the connected devices, even in the power saving mode.
• When the main power of the monitor is off, a device connected to the USB downstream port will not operate.
• When the “USB CHARGE Port” setting in “Preferences” is set to “Charging Only”, a peripheral device will not work if connected to the “CHARGE” port.
• Ensure that communication between all peripheral devices connected to the monitor and the PC is ended before switching the “USB CHARGE Port” setting. When the
setting is switched, all communication will be temporarily interrupted.
- 42 -
Chapter 6 Reference
●●Connection Procedure (Setup of USB Function)
1. Connect the monitor first to a PC using the signal cable, and start the PC.
2. Connect the USB cable between the USB downstream port of the PC and the USB upstream port of the monitor.
The USB hub function is set up automatically upon connection of the USB cable.
3. Connect the peripheral USB device to the USB downstream port of the monitor.
“CHARGE” port
USB upstream
port
USB
downstream
port
- 43 -
Chapter 6 Reference
6-7. Specifications
LCD Panel
Type
IPS (Anti-Glare)
Backlight
Size
Wide color gamut LED
61 cm (24.0inch)
Resolution
1920 dots × 1200 lines
Display Size (H × V)
518.4 mm × 324.0 mm
Pixel Pitch
0.270mm×0.270mm
Display Colors
Approx. 1073.74 million colors (for 10 bit input)
Viewing Angle (H / V, typical)
178˚ / 178˚
Recommended Brightness (typical) 120 cd/m2 or less (Temperature: 5000 K to 6500 K)
Contrast Ratio (typical)
1000 : 1 (When “DUE Priority” setting is “Brightness”)
Response Time (typical)
Black-white-black: 13 ms
Gray-to-gray: 15 ms
Adobe® RGB coverage: 99%, NTSC ratio 110%
Color Gamut Display (typical)
Video Signals
Input Terminals
Vertical scan frequency
DVI-D x 1 (Single Link, applicable to HDCP)
HDMI x 1 (Applicable to HDCP)
DisplayPort x 1(Applicable to HDCP)
26 kHz to 78 kHz (DVI, DisplayPort, HDMI PC)
15 kHz to 78 kHz (HDMI Video)
24 Hz to 61 Hz (720 x 400 : 69 Hz to71 Hz)
Frame Synchronization Mode
23.75 Hz to 30.5 Hz, 47.5 Hz to 61.0 Hz
Dot clock (Max.)
164 MHz
Port
Upstream port × 1, downstream port × 3 (The “CHARGE” port supports quick recharging)
Standard
Communication Speed
USB Specification Rev. 3.0
USB Battery Charging Specification Rev.1.2
5 Gbps (super), 480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low)
Supply Current
Downstream:
Max. 900 mA per port
Downstream (CHARGE Port):
Normal: Max. 1.5 A per port, Charging Only: Max. 2.1 A per port
Horizontal scan frequency
USB
Power
Input
100–240 VAC ±10%, 50/60 Hz, 0.95 A–0.50 A)
Maximum Power Consumption
92 W or less
Power Save Mode
0.7 W or less
Standby Mode
0.6 W or less
(When DisplayPort 1 connector is input, “Auto Input Detection” is set to “Off”, and no USB device is
connected; or the USB CHARGE port is set to “Normal”, and the OS is in sleep mode; or when the
monitor’s power off setting is activated)
(When “Auto Input Detection” is set to “Off”, and no USB device is connected; or the USB CHARGE
port is set to “Normal”, “DP Power Save” is set to “On”)
- 44 -
Chapter 6 Reference
Physical
­Specifications
Dimensions
Dimensions (Without Stand)
Net. weight
Net Weight (Without Stand)
Height adjustment
Tilt
Swivel
Vertical Rotation
Operating
­ nvironment
E
­Requirements
Temperature
Humidity
Air Pressure
Transportation/
Temperature
Storage Environment Humidity
Requirements
Air Pressure
Min. height: 554.4 mm × 396 mm × 245 mm (W × H × D) (Tilt: 0˚)
Max. height: 554.4 mm × 558 mm × 265 mm (W × H × D) (Tilt: 35˚)
554.4 mm × 362 mm × 64 mm (W × H × D)
Approx. 7.8 kg
Approx. 5.0 kg
155 mm (Tilt: 0˚) / 145mm (Tilt: 35˚)
Up 35˚, down 5˚
344°
Clockwise 90°
0˚C to 35˚C (32˚F to 95˚F)
20% to 80% R.H. (no condensation)
540 hPa to 1060 hPa
-20 ˚C to 60 ˚C (-4 ˚F to 140 ˚F)
10% to 90% R.H. (no condensation)
200 hPa to 1060 hPa
- 45 -
Chapter 6 Reference
●●Dimensions
491.3
558
413
30
64
145
5°
5°
636.4
35°
35°
Unit: mm
344°
265
554.4
519.8
341.5
100
VESA
122.6
(227.2)
11
(131)
155
34
362
396-551
565.4-647.2
325.4
°
133.7
61.3
90
100
VESA
(131)
(227.2)
62.7
245
- 46 -
Chapter 6 Reference
●●Main Default Settings
Color Mode
Picture Expansion
Input Color Format
Input Range
Noise Reduction
Auto Input Detection
Menu Rotation
USB CHARGE Port
Power Save
Indicator
Beep
Language
Logo
Key Lock
Signal Format
DVI input
DisplayPort input
HDMI input
DisplayPort input
HDMI input
DVI input
DisplayPort input
HDMI input
DisplayPort
HDMI
Custom
Aspect Ratio
Aspect Ratio
Aspect Ratio (When “Auto” is enabled: Auto)
Auto
RGB (When “Auto” is enabled: Auto)
Full
Auto
Auto
Off
Off
0°
Normal
On
4
On
English
On
Off
RGB
PC
●●Accessories
For the latest information about the accessories, refer to our web site. www.eizoglobal.com
- 47 -
Chapter 7 Glossary
Chapter 7 Glossary
Adobe®RGB
This is a definition of the practical RGB color space proposed by Adobe Systems in 1998. The color reproduction range (color gamut) is broader than
sRGB, and is highly adaptable to such fields as printing etc.
Color Space
YUV and RGB, etc. are available. YUV expresses the color by using the luminance (Y), the color difference of Blue (U), and the color difference of Red (V).
RGB does this by using the gradation of the 3 colors, Red (R), Green (G), and Blue (B).
DisplayPort
This is the interface standard for image signals standardized in accordance with VESA. It was developed with the aim of replacing the conventional DVI
and analog interfaces, and it can transmit high resolution signals and sound signals, which DVI does not support. The standard size and mini size
connectors have been standardized.
DVI (Digital Visual Interface)
DVI is a digital interface standard. DVI allows direct transmission of the PC’s digital data without loss.
This adopts the TMDS transmission system and DVI connectors. There are two types of DVI connectors. One is a DVI-D connector for digital signal input
only. The other is a DVI-I connector for both digital and analog signal inputs.
Gain
The brightness of each color component red, green, and blue is called Gain. An LCD monitor displays the color by the light passing through the panel color
filter. Red, green and blue are the three primary colors. All the colors on the screen are displayed by combining these three colors. The color tone can be
changed by adjusting the light intensity (volume) passing through each color’s filter.
Gamma
Generally, the monitor brightness varies nonlinearly with the input signal level, which is called “Gamma Characteristic”. When the gamma value is low, the
middle tone area is displayed brighter, and darker when high. Changes to the gamma value will not affect contrast. A gamma value appropriate for the
display content should be selected.
- 48 -
Chapter 7 Glossary
HDCP (High-bandwidth Digital Content Protection)
Digital signal coding system developed to copy-protect the digital contents, such as video, music, etc.
This helps to transmit the digital contents safely by coding the digital contents sent via the DVI or HDMI connector on the output side and decoding them
on the input side.
Any digital contents cannot be reproduced if both of the equipments on the output and input sides are not applicable to HDCP system.
HDMI (High-Definition Multimedia Interface)
HDMI is a digital interface standard, developed for consumer electrical appliance or AV device. This standard is issued on the basis of the DVI standard
which is one of an interface specification for the connection between a PC and a monitor. The projected image, sound and control signal without
compressed enable to be transmitted with one cable.
L*
L* is a lightness value based on the CIELUV and CIELAB color spaces. CIELUV and CIELAB are color spaces that describe the relationship between color
and human vision, in which L* corresponds to perceived brightness.
Resolution
The LCD panel consists of numerous pixels of specified size, which are illuminated to form images. This monitor consists of horizontal 1920 pixels and
1200 vertical pixels. At a resolution of 1920 × 1200, all pixels are illuminated as a full screen (1:1).
sRGB (Standard RGB)
International standard for color reproduction and color space among peripheral devices (such as monitors, printers, digital cameras, scanners). As a form
of simple color matching for the Internet, colors can be displayed using tones close to those of the transmission and reception devices.
Temperature
Color temperature is a method to measure the white color tone, generally indicated in degrees Kelvin. The screen becomes reddish at a low temperature,
and bluish at a high temperature, like the flame temperature.
5000 K: Slightly reddish white
6500 K: White referred to as daylight-balanced color
9300 K: Slightly bluish white
- 49 -
Appendix
Appendix
Trademark
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing, LLC in the
United States and other countries.
The DisplayPort Compliance Logo and VESA are registered trademarks of the Video Electronics Standards Association.
The SuperSpeed USB Trident Logo is a registered trademark of USB Implementers Forum, Inc.
The USB Power Delivery Trident Logos are trademarks of USB Implementers Forum, Inc.
DICOM is the registered trademark of the National Electrical Manufacturers Association for its standards publications relating to digital communications of
medical information.
Kensington and Microsaver are registered trademarks of ACCO Brands Corporation.
Thunderbolt is a trademark of Intel Corporation in the United States and/or other countries.
Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and other countries.
Adobe is a registered trademark of Adobe Systems Incorporated in the United States and other countries.
Apple, macOS, Mac OS, OS X, Macintosh and ColorSync are registered trademarks of Apple Inc.
EIZO, the EIZO Logo, ColorEdge, CuratOR, DuraVision, FlexScan, FORIS, RadiCS, RadiForce, RadiNET, Raptor and ScreenManager are registered
trademarks of EIZO Corporation in Japan and other countries.
ColorEdge Tablet Controller, ColorNavigator, EcoView NET, EIZO EasyPIX, EIZO Monitor Configurator, EIZO ScreenSlicer, G-Ignition, i•Sound, Quick Color
Match, RadiLight, Re/Vue, SafeGuard, Screen Administrator, Screen InStyle, ScreenCleaner and UniColor Pro are trademarks of EIZO Corporation.
All other company and product names are trademarks or registered trademarks of their respective owners.
License
The bitmap font used for this product is designed by Ricoh Industrial Solutions Inc.
- 50 -
Appendix
FCC Declaration of Conformity
For U.S.A. , Canada, etc. (rated 100-120 Vac) Only
FCC Declaration of Conformity
We, the Responsible Party
EIZO Inc.
5710 Warland Drive, Cypress, CA 90630
Phone: (562) 431-5011
declare that the product
Trade name: EIZO
Model: ColorEdge CS2420
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures.
*
*
*
*
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
- 51 -
Appendix
Note
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep interference within the limits of a Class B digital device.
- AC Cord
- Shielded Signal Cable (enclosed)
Canadian Notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.
- 52 -
03V25650B1
UM-CS2420
Copyright © 2016-2019 EIZO Corporation. All rights reserved.
2nd Edition-May, 2019
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising