Eizo | RX250 | Owner Manual | Eizo RX250 Owner Manual

Eizo RX250 Owner Manual
Color LCD monitor
Important
Please read this “Instructions for Use”, and “Installation Manual”
(separate volume) carefully to familiarize yourself with safe and
effective usage.
Please retain this manual for future reference.
• For monitor adjustment and settings, refer to the “Installation
Manual”.
• For the latest product information including the “Instructions for
Use”, refer to our web site :
http://www.eizoglobal.com
English
Instructions for Use
SAFETY SYMBOLS
This manual and this product use the safety symbols below. They denote critical information. Please read
them carefully.
WARNING
CAUTION
Failure to abide by the information in a
WARNING may result in serious injury
and can be life threatening.
Failure to abide by the information in a
CAUTION may result in moderate injury and/or
property or product damage.
Indicates a warning or caution. For example,
Indicates a prohibited action. For example,
Indicates a mandatory action. For example,
indicates an “electrical shock” hazard.
means “Do not disassemble”.
means “Ground the unit”.
This product has been adjusted specifically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specifications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information confidential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specifications are subject to change without notice.
2

PRECAUTIONS
• This product has been adjusted specifically for use in the region to which it was originally shipped.
If the product is used outside the region, it may not operate as specified in the specifications.
• To personal safety and proper maintenance, please read carefully this section and the caution
statements on the monitor.
Location of the Caution Statements
WARNING
AVERTISSEMENT
WARNUNG
Symbols on the unit
Symbol
This symbol indicates
Main Power Switch:
Press to turn the monitor’s main power off.
Main Power Switch:
Press to turn the monitor’s main power on.
Power button:
Press to turn the monitor’s power on or off.
Alternating current
Alerting electrical hazard
CAUTION:
Refer to “SAFETY SYMBOLS” (page 2).
WEEE marking:
Product must be disposed of separately; materials may
be recycled.
CE marking:
EU conformity mark in accordance with the provisions of
Council Directive 93/42/EEC and 2011/65EU.
Manufacturer
Date of manufacture
PRECAUTIONS
3
English
IMPORTANT
WARNING
If the unit begins to emit smoke, smells like something is burning, or makes strange noises, disconnect all power connections immediately and contact your EIZO representative for advice.
Attempting to use a malfunctioning unit may result in fire, electric shock, or equipment damage.
Do not open the cabinet or modify the unit.
Opening the cabinet or modifying the unit may result in fire, electric shock, or burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing covers may result in fire, electric
shock, or equipment damage.
Keep small objects or liquids away from the unit.
Small objects accidentally falling through the ventilation slots into the cabinet or spillage
into the cabinet may result in fire, electric shock, or equipment damage. If an object or
liquid falls/spills into the cabinet, unplug the unit immediately. Have the unit checked by
a qualified service engineer before using it again.
Place the unit at a sturdy and stable place.
A unit placed on an inadequate surface may fall and result in injury or equipment damage. If the unit falls,
disconnect the power immediately and ask your local EIZO representative for advice. Do not continue using
a damaged unit. Using a damaged unit may result in fire or electric shock.
Use the unit in an appropriate location.
Otherwise, fire, electric shock, or equipment damage may result.
•
•
•
•
•
•
•
•
•
•
Do not place outdoors.
Do not place in any form of transportation (ships, aircraft, trains, automobiles, etc.).
Do not place in dusty or humid environments.
Do not place in locations where water may be splashed on the screen (bathrooms, kitchens,
etc.)
Do not place in locations where steam comes in direct contact with the screen.
Do not place near heat generating devices or humidifiers.
Do not place in locations where the product is subject to direct sunlight.
Do not place in environments with inflammable gas.
Do not place in environments with corrosive gases (such as sulfur dioxide, hydrogen sulfide,
nitrogen dioxide, chlorine, ammonia, and ozone)
Do not place in environments with dust, components that accelerate corrosion in the
atmosphere (such as sodium chloride and sulfur), conductive metals, and so on
To avoid danger of suffocation, keep the plastic packing bags away from babies and children.
Use the enclosed power cord and connect to the standard power outlet in your country.
Be sure to use within the rated voltage of the power cord. Otherwise, fire or electric shock may result.
Power supply: 100-240Vac 50/60Hz
To disconnect the power cord, grasp the plug firmly and pull.
Tugging on the cord may damage and result in fire or electric shock.
The equipment must be connected to a grounded main outlet.
Failure to do so may result in fire or electric shock.
Use the correct voltage.
• The unit is designed for use with a specific voltage only. Connection to another voltage than specified in this
“Instructions for Use” may cause fire, electric shock, or equipment damage.
Power supply: 100-240Vac 50/60Hz
• Do not overload your power circuit, as this may result in fire or electric shock.
4
PRECAUTIONS
WARNING
English
Handle the power cord with care.
• Do not place the cord underneath the unit or other heavy objects.
• Do not pull on or tie the cord.
If the power cord becomes damaged, stop using it. Using of a damaged cord may result
in fire or electric shock.
For electrical safety, do not connect or disconnect the power cord in the presence of patients.
Never touch the plug and power cord if it begins to thunder.
Touching them may result in electric shock.
When attaching an arm stand, please refer to the user’s manual of the arm stand and install the unit
securely.
Otherwise, the unit may become detached, resulting in injury and/or equipment damage. Before installation,
make sure that desks, walls, or any other installation surface has adequate mechanical strength. If the unit
falls, please ask your local EIZO representative for advice. Do not continue using a damaged unit. Using
a damaged unit may result in fire or electric shock. When reattaching the tilt stand, please use the same
screws and tighten them securely.
Do not touch a damaged LCD panel directly with bare hands.
Liquid crystal is poisonous. If any part of your skin comes in direct contact with the
panel, wash thoroughly. If liquid crystal enters your eyes or mouth, immediately flush
with large amounts of water and seek medical attention.
Fluorescent backlight lamps contain mercury (the products that have LED backlight lamps contain no mercury), dispose according to local, state or federal
laws.
Exposure to elemental mercury can result in effects on the nervous system, including
tremors, memory loss, and headaches.
PRECAUTIONS
5
CAUTION
Handle with care when carrying the unit.
Disconnect the power cord and cables when moving the unit. Moving the unit with the power cord or cables
attached is dangerous and may result in injury.
Carry or place the unit according to the correct specified methods.
• When carrying, grasp and firmly hold the unit as shown in the illustration below.
• Monitors of size 30 inches and above are heavy. When unpacking and/or carrying the monitor,
ensure at least two people are utilized.
Dropping the unit may result in injury or equipment
damage.
Do not block the ventilation slots on the cabinet.
• Do not place any objects on the ventilation slots.
• Do not install the unit in a place with poor ventilation or inadequate space.
• Do not use the unit laid down or upside down.
Blocking the ventilation slots prevents proper airflow and may result in fire, electric
shock, or equipment damage.
Do not touch the plug with wet hands.
Doing so may result in electrical shock.
Use an easily accessible power outlet.
This is to facilitate disconnecting the power in case of a problem.
Periodically clean the area around the power plug and the ventilation slot of the monitor.
Dust, water, or oil on the plug may result in fire.
Unplug the unit before cleaning it.
Cleaning the unit while it is plugged into a power outlet may result in electric shock.
If you plan to leave the unit unused for an extended period of time, disconnect the power cord from
the wall socket after turning off the power switch for the safety and the power conservation.
This product is suitable for placing near patients, but not for direct contact with patients.
6
PRECAUTIONS
Notice for this monitor
English
Intended use
This product is intended to be used in displaying and viewing digital images for review, analysis and
diagnosis by trained medical practitioners. It does not support the display of mammography images
for diagnosis.
Caution: Federal law (USA) restricts this device to sale by or on the order of a physician.
Attention
• This product may not be covered by warranty for uses other than those described in this manual.
• The specifications noted in this manual are only applicable when the following are used:
-- Power cords provided with the product
-- Signal cables specified by us
• Only use optional products manufactured or specified by us with this product.
Installation Requirements
• Carefully read the “PRECAUTIONS” (page 3) and always follow the instructions.
• When installing the monitor in a rack, ensure that there is adequate space around the sides, back
and top of the monitor.
• Position the monitor so that there is no light to interfere with the screen.
• If you place this product on a lacquer-coated desk, the color may adhere to the bottom of
the stand due to the composition of the rubber. Check the desk surface before use.
Maintenance
• The display quality of monitors is affected by the quality level of input signals and the degradation of
the product. It is recommended that daily checkups and periodical constancy test be performed to
comply with medical standards/guidelines according to your application. Use of the RadiCS monitor
quality control software enables you to perform high-level total quality control that meets medical
standards/guidelines.
• It takes about 15 minutes for the performance of electrical parts to stabilize. Please wait 15 minutes
or more after the monitor power has been turned on or the monitor has recovered from the power
saving mode, and then adjust the monitor.
• Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term
use and maintain a stable display. Periodically perform constancy tests. Calibrate if necessary. For
details, refer to the User Manuals for the RadiCS/RadiCS LE monitor quality control software.
• To maintain the measurement accuracy of the integrated front sensor, perform periodical correlation
using RadiCS/RadiCS LE.
• Parts (such as the LCD panel) may deteriorate over the long term. Periodically check that they are
operating normally.
• When the screen image is changed after displaying the same image for extended periods of time,
an afterimage may appear. Use the screen saver or power save function to avoid displaying the
same image for extended periods of time.
• If the monitor displays continuously over a long period of time, dark smudges or burn-in may
appear. To maximize the life of the monitor, we recommend the monitor be turned off periodically.
Notice for this monitor
7
• The backlight of the LCD panel has a fixed lifetime. When the screen becomes dark or begins to
flicker, please contact your local EIZO representative.
• The screen may have defective pixels or a small number of light dots on the screen. This is due to
the characteristics of the panel itself, and is not a malfunction of the product.
• Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions,
such as interference patterns, etc. If pressure is continually applied to the panel, it may deteriorate
or damage your panel. (If the pressure marks remain on the panel, leave the monitor with a black or
white screen. The symptom may disappear.)
• Do not scratch or press on the panel with any sharp objects, as this may result in damage to the
panel. Do not attempt to brush with tissues as this may scratch the panel.
• When the monitor is cold and brought into a room or the room temperature goes up quickly, dew
condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not
turn the monitor on. Instead wait until the dew condensation disappears, otherwise it may cause
some damage to the monitor.
Cleaning
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation
lifetime.
Attention
• Do not use chemicals on a frequent basis. Chemicals such as alcohol and antiseptic solution may cause
gloss variation, tarnishing, and fading of the cabinet or panel, and also quality deterioration of the image.
• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.
• Do not let chemicals come into direct contact with the monitor.
Note
• The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface.
Gently wipe off any dirt on the cabinet or panel surface with a soft cloth soaked in a small amount of
water or one of the chemicals listed below.
Chemicals that may be used for cleaning
Material name
Ethanol
Isopropyl alcohol
Chlorhexidine
Sodium hypochlorite
Benzalkonium chloride
Alkyldiaminoethylglycine
Glutaral
Glutaral
Ethanol
Isopropyl alcohol
Hibitane
Purelox
Welpas
Tego 51
Sterihyde
Cidex Plus28
Product name
To use the monitor comfortably
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
• Look at the screen from a proper distance and from a proper angle.
8
Notice for this monitor
CONTENTS
English
PRECAUTIONS....................................................... 3
IMPORTANT............................................................... 3
Notice for this monitor.......................................... 7
CONTENTS.............................................................. 9
Chapter 1
Introduction...................................... 10
1-1.
Features.........................................................10
1-2.
Package Contents.........................................11
1-3.
EIZO LCD Utility Disk...................................11
●●
●●
Disk contents and software overview.............11
Using RadiCS LE............................................11
1-4.
Controls and Functions...............................12
1-5.
Compatible Resolutions..............................13
Chapter 2
Connection....................................... 14
2-1.
Connecting Cables.......................................14
2-2.
Making Use of USB (Universal Serial Bus)....16
●●Required system environment........................16
●●Connection procedure (Setup of USB function)....17
Chapter 3
Setting Up......................................... 18
3-1.
Adjusting the Screen Height and Angle.....18
3-2.
Attaching Arm...............................................19
Chapter 4
Troubleshooting............................... 20
Chapter 5
Specifications.................................. 21
5-1.
Specifications List........................................21
5-2.
Main Default Settings.................................. 22
5-3.
Dimensions................................................... 23
5-4.
Accessories.................................................. 23
Chapter 6
Glossary........................................... 24
Appendix............................................................... 26
Trademark................................................................ 26
License / Copyright................................................. 27
Medical Standard.................................................... 27
EMC Information..................................................... 28
FCC Declaration of Conformity............................. 33
Recycling Information/
Informationen zum Thema Recycling/
Informations sur le recyclage/
Сведения по утилизации..................................... i
CONTENTS
9
Chapter 1 Introduction
Thank you very much for choosing an EIZO color LCD monitor.
1-1. Features
• 21.3 inches
• Supports a resolution of 2M pixels (Portrait: 1200 × 1600 dots (H × V))
• Uses high-contrast panel (1400 : 1).
Enables the display of sharp images.
• Applicable to DisplayPort (applicable to 8 bit or 10 bit, not applicable to audio signals)
• The daisy-chain function is included enabling multiple monitors to be connected with the
DisplayPort cable.
A graphic board supporting DisplayPort1.2 is required. For details, refer to the EIZO website.
http://www.eizoglobal.com
• The CAL Switch function allows the user to select the display mode optimum to the displayed
image.
Refer to the Installation Manual (on the CD-ROM).
• Selectable DICOM (page 24) Part 14 complied screen.
• The quality control software “RadiCS LE” used to calibrate the monitor and to manage the history is
included.
See “1-3. EIZO LCD Utility Disk” (page 11).
• Power saving function
This product is equipped with power saving function.
-- 0 W power consumption when the main power is off
Equipped with main power switch.
When not using the monitor, you can turn off the main power supply so that the power is cut completely.
-- Presence Sensor
The sensor on the front side of the monitor detects the movement of a person. When a person moves
away from the monitor, the monitor shifts to the power saving mode automatically and does not display the
images on the screen. Therefore, the function reduces the power consumption.
Refer to the Installation Manual (on the CD-ROM).
• Low-profile and lightweight design
• Long service life LED backlight LCD panel
• Built-in ambient light sensor
Depending on the environment, the sensor sometimes indicates different values from those measured by a
stand-alone illuminance meter.
The usage of this sensor requires the quality control software “RadiCS/RadiCS LE” and the measurement is
always triggered by the user’s operation in the corresponding menu. For further details about the measured
value and how to execute the measurement, refer to the RadiCS/RadiCS LE User’s Manual (on the CD-ROM).
10
Chapter 1 Introduction
1-2. Package Contents
Note
• Please keep the packaging box and materials for future movement or transport of the monitor.
• Monitor
• Power cord
• USB cable : UU300
• EIZO LCD Utility Disk (CD-ROM)
• Instructions for Use (this manual)
• Digital signal cable : PP300
DisplayPort - DisplayPort
• Digital signal cable : DD300
DVI - DVI (Single Link)
1-3. EIZO LCD Utility Disk
An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk
contents and the overview of the software programs.
●●Disk contents and software overview
The disk includes quality control software and User’s Manual. Refer to Readme.txt file on the disk for
software startup procedures or file access procedures.
Contents
Overview
Readme.txt file
RadiCS LE (for Windows)
Quality control software for calibrating the monitor and managing the
calibration history.
Installation Manual of this monitor (PDF file)
“Instructions for Use” of this monitor (PDF file)
●●Using RadiCS LE
For the installation and use of RadiCS LE, refer to the User’s Manual on the disk.
When using this software, you will need to connect a PC to the monitor with the supplied USB cable
(see “2-2. Making Use of USB (Universal Serial Bus)” (page 16)).
Note
• Using DDC communication allows you to use RadiCS LE without having to use the USB cable. For
information on how to configure DDC communication, refer to the Installation Manual (on the CD-ROM).
Chapter 1 Introduction
11
English
Check that all the following items are included in the packaging box. If any items are missing or damaged,
contact your local EIZO representative.
1-4. Controls and Functions
1
2
Approx. 30˚
12
13
6
15
14
Adjustment menu*1
3
1. Integrated Front Sensor
(Mobile)
2. Ambient Light Sensor
3. Presence Sensor
4. Operation switches
5.
switch
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
*1
12
4
5
6
7
8
9
10
11
Detects the movement of a person in front of the monitor.
Measures the environmental illumination.
Detects the movement of a person in front of the monitor.
Displays the menu. Follow the guide to perform the desired operations.
• Turns the power on or off.
• Indicates the monitor’s operation status.
Green: Operating, Orange: Power saving mode, Off: Main power/power off
USB downstream port
Connects a peripheral USB device.
USB upstream port
Connects the USB cable to use the software that needs USB connection, or to use
USB Hub function.
DVI-D connector
Connect it to the PC.
DisplayPort input
Connect it to the PC. To set up a daisy-chain connection, connect the cable to the
connector
output connector of an upstream monitor.
DisplayPort output
To set up a daisy-chain connection, connect the cable to the input connector of a
connector
downstream monitor.
Power connector
Connects the power cord.
Used to adjust the height and angle of the monitor screen.
Stand
Main power switch
Turns the main power on or off. : Off : On
Security lock slot
Complies with Kensington’s MicroSaver security system.
Cable holder
Covers the monitor cables.
For instructions for use, refer to the Installation Manual (on the CD-ROM).
Chapter 1 Introduction
1-5. Compatible Resolutions
Resolution
vertical scan
frequency
720 × 400
70 Hz
640 × 480
60 Hz
800 × 600
60 Hz
1024 × 768
60 Hz
1280 × 1024
60 Hz
1200 × 1600
60 Hz
1600 × 1200
60 Hz
*1 Supports 10-bit displays.
DisplayPort*1
Portrait
Landscape
√
√
√
√
√
-
√
√
√
√
√
√
Portrait
√
√
√
√
√
-
DVI
√ : Supported
Landscape
√
√
√
√
√
√
Chapter 1 Introduction
13
English
The monitor supports the following resolutions.
Chapter 2 Connection
2-1. Connecting Cables
Attention
•• Check that the monitor and the PC are powered off.
•• When replacing the current monitor with this monitor, refer to “1-5. Compatible Resolutions” (page 13) to
change the PC settings for resolution and vertical scan frequency to those that are available for this monitor,
before connecting the PC.
1. Turn the monitor screen 90˚ in clockwise direction.
The landscape position is the default monitor orientation.
Attention
•• Before turning the monitor screen, raise it to the highest position.
2. Connect signal cables.
Check the shapes of the connectors, and connect the cables. After connecting the DVI cable, tighten
the fasteners to secure the connector.
Connecting to a single PC
Attention
•• The DisplayPort connectors of the monitor consist of input
PC, connect the cable to input connector .
Signal cable :
DD300
Signal cable : PP300
14
Chapter 2 Connection
or
and output
. When connecting a monitor to a
Connecting to multiple PCs
For information on how to switch the input signals, refer to the Setup manual (on the CD-ROM).
English
Signal cable : DD300
Signal cable : PP300
Daisy-chaining multiple monitors
Attention
•• Visit the EIZO website for information about monitors and graphic boards that can be used for the daisy-chain
connection: http://www.eizoglobal.com
•• Remove the
cap before connecting the signal cable.
Connecting to a Computer
Signal cable : PP300
Signal cable : PP300
Signal cable : PP200
Chapter 2 Connection
15
3. Plug the power cord into a power outlet and the power connector on the
monitor.
4. Connect the USB cable when using RadiCS LE.
For information about the connection to the USB upstream port, refer to “2-2. Making Use of USB
(Universal Serial Bus)” (page 16).
Connecting to the Monitor
Connecting to a Computer
Note
•• Using DDC communication allows you to use RadiCS LE without having to use the USB cable. For
information on how to configure DDC communication, refer to the Installation Manual (on the CD-ROM).
5. Touch
to turn on the power to the monitor.
The monitor’s power indicator lights up green.
6. Turn on the PC.
The screen image appears.
If an image does not appear, refer to “Chapter 4 Troubleshooting” (page 20) for additional advice.
Attention
•• For the maximum power saving, it is recommended that the Power button be turned off. When not using
the monitor, you can turn off the main power supply or disconnect the power plug so that the power is cut
completely.
Note
•• In order to maximize the monitor life and to minimize luminance deterioration as well as power consumption,
proceed the following:
-- Use the power saving function of the computer.
-- Turn off the monitor and PC after using them.
2-2. Making Use of USB (Universal Serial Bus)
This monitor has a hub compatible with USB. Connected to a PC compatible with USB or another USB
hub, this monitor functions as a USB hub allowing connection to peripheral USB devices.
●●Required system environment
•• A PC equipped with a USB port or another USB hub connected to a USB compatible PC
•• Windows 10 / Windows 8.1 / Windows 8 / Windows 7 / Windows Vista / Windows XP, or Mac OS X
10.2 or later
•• USB cable
Attention
•• This monitor may not work depending on PC, OS or peripheral devices to be used. For USB compatibility of
peripheral devices, contact their manufacturers.
•• Devices connected to the USB downstream port still work when the monitor is in power saving mode or when
the power is switched off using only the power button of the monitor. Therefore, power consumption of the
monitor varies with connected devices even in the power saving mode.
•• When the main power switch is Off, device connected to the USB port will not operate.
16
Chapter 2 Connection
●●Connection procedure (Setup of USB function)
1. Connect the monitor first to a PC using the signal cable, and run the PC.
The USB hub function is set up automatically upon connection of the USB cable.
3. Connect the peripheral USB device to the USB downstream port of the monitor.
USB
downstream
port
USB
upstream
port
Chapter 2 Connection
17
English
2. Connect the supplied USB cable between the USB downstream port of a USB compatible PC (or
another USB hub) and the monitor’s USB upstream port.
Chapter 3 Setting Up
3-1. Adjusting the Screen Height and Angle
Hold left and right edge of the monitor with both hands, and adjust the screen height, tilt and swivel of the
screen to the best condition for working.
Attention
•• After carrying out the adjustment, make sure that the cables are connected correctly, and put them through the
cable holder.
18
Chapter 3 Setting Up
3-2. Attaching Arm
Attention
•• When attaching an arm or stand, follow the instructions of their User’s Manual.
•• When using another manufacturer’s arm or stand, confirm the following in advance and select one conforming to
the VESA standard.
-- Clearance between the screw holes: 100mm × 100 mm
-- VESA mount of the arm or stand, external dimensions: 122 mm x 122 mm or less
-- Strong enough to support weight of the monitor unit (except the stand) and attachments such as cables.
•• When using another manufacturer’s arm or stand, use the following screws to secure it.
-- Screws fixing the stand to the monitor
•• When using an arm or stand, attach it to meet the following tilt angles of the monitor.
-- Up 45˚, down 45˚ (when the portrait orientation is used, and when rotated 90° counterclockwise for landscape
display)
•• Connect the cables after attaching an arm or stand.
•• Do not move the removed stand up and down. Doing so may result in injury or device damage.
•• The monitor and arm or stand are heavy. Dropping them may result in injury or equipment damage.
•• Periodically check the tightness of the screws. If not sufficiently tight, the monitor may detach from the arm, which
may result in injury or equipment damage.
Procedure
1. Lay the LCD monitor on a soft cloth spread over on a stable surface with the
panel surface facing down.
2. Remove the stand.
Prepare a screwdriver. Loosen the screws (four) securing the unit and the stand with the screwdriver.
3. Attach the arm or stand to the monitor.
Use the screws that you removed in step 2 to attach the arm (or stand) to the monitor.
Chapter 3 Setting Up
19
English
An optional arm (or an optional stand) can be attached by removing the stand section. For supported
optional arms (or optional stands), refer to the EIZO website: http://www.eizoglobal.com
Chapter 4 Troubleshooting
If a problem still remains after applying the suggested remedies, contact your local EIZO representative.
Problem
1. No picture
• Power indicator does not light.
• Power indicator is lighting green.
• Power indicator is lighting orange.
• Power indicator is flashing orange and green.
2. The message below appears.
20
Possible cause and remedy
•
•
•
•
Check whether the power cord is connected properly.
Turn the main power switch on.
Touch .
Turn off the main power, and then turn it on again.
• Increase “Brightness”, “Contrast”, and/or “Gain” in the
Adjustment menu. For details, refer to the Installation
Manual (on the CD-ROM).
• Turn off the main power, and then turn it on again.
• Switch the input signal. For details, refer to the Installation
Manual (on the CD-ROM).
• Move the mouse or press any key on the keyboard.
• Check whether the PC is turned on.
• When Presence Sensor is set to “On”, the monitor may
have shifted to the power saving mode. Come near to the
monitor.
• Check if the signal cable is connected to
for inputting
the DisplayPort signal.
is used for output when a daisychain connection is set up.
• Turn off the main power, and then turn it on again.
• Connect via the signal cable specified by EIZO. Turn off
the main power, and then turn it on again.
• When connected to DisplayPort, switch the version of
DisplayPort to 1.1. For details, refer to the Installation
Manual (on the CD-ROM).
This message appears when the signal is not input correctly
even when the monitor functions properly.
• This message appears when no signal is
input.
Example:
• The message shown left may appear, because some PCs
do not output the signal soon after power-on.
• Check whether the PC is turned on.
• Check whether the signal cable is connected properly.
• Switch the input signal. For details, refer to the Installation
Manual (on the CD-ROM).
• When connected to DisplayPort, switch the version of
DisplayPort to 1.1.
• Check if the signal cable is connected to
for inputting
the DisplayPort signal.
is used for output when a daisychain connection is set up.
• Turn off the main power, and then turn it on again.
• The message shows that the input signal is
out of the specified frequency range.
Example:
• Check whether the PC is configured to meet the resolution
and vertical scan frequency requirements of the monitor
(see “1-5. Compatible Resolutions” (page 13)).
• Reboot the PC.
• Select an appropriate setting using the graphics board’s
utility. Refer to the manual of the graphics board for
details.
Chapter 4 Troubleshooting
Chapter 5 Specifications
English
5-1. Specifications List
LCD Panel
Type
RX250
IPS (Anti-Glare)
RX250-AR
IPS (Anti-reflection)
Backlight
LED
Size
54.0 cm (21.3 inch)
Resolution
2M pixels (Portrait orientation: 1200 dots × 1600 lines (H × V))
Display Size (H x V)
324.0 mm × 432.0 mm (Portrait orientation)
Pixel Pitch
0.270 mm
Display Colors
10-bit (DisplayPort) : 1073.74 million colors (Max.)
8-bit (DVI) : 16.77 million colors
Video Signals
USB
Power
Physical
Specifications
Viewing Angles
(H / V, typical)
178˚ / 178˚
Recommended
Brightness
400 cd/m2
Response Time (typical)
20 ms (black -> white -> black)
Input Terminals
DVI-D (Single Link) × 1, DisplayPort × 1
Output Terminal
DisplayPort x 1
Digital Scanning
Frequency
(H / V)
31 kHz - 100 kHz / 59 Hz - 61 Hz (VGA TEXT: 69 Hz - 71 Hz)
Frame synchronous mode : 59 Hz - 61 Hz
Dot clock
25.0 MHz - 164.5 MHz
Port
Upstream port × 1, Downstream port × 2
Standard
USB Specification Revision 2.0
Input
100 - 240 VAC +/-10%, 50/60 Hz, 0.80 A - 0.35 A
Maximum Power
Consumption
79 W or less
Power Save Mode
1.0W or less (When DVI input is used, no USB device is
connected, "Auto Input Detection": "Off", "Power
Save": "High", "DDC": "Off", "DC5V Output": "Off",
"DP Power Save": "On", "DisplayPort version": "1.1",
no external load is connected)
Standby Mode
1.0W or less (When no USB device is connected, "DP Power
Save": "On", "DC5V Output": "Off", "DisplayPort
version": "1.1", "DDC": "Off", no external load is
connected)
Dimensions
361.0 mm × 510.5 mm - 600.5 mm × 267.0 mm ( W × H × D ) (Tilt:
30˚)
Dimensions (Without
Stand)
361 mm × 465 mm × 78 mm ( W × H × D )
Net Weight
Approx. 8.2 kg
Net Weight (Without
Stand)
Approx. 5.4kg
Height Adjustment Range 90mm (Tilt: 0˚)
Operating
Environmental
Requirements
Tilt
Up 30˚, down 5˚
Swivel
70˚
Rotation
90˚ (counterclockwise for portrait display)
Temperature:
0˚C to 35˚C (32˚F to 95˚F)
Humidity
20% to 80% R.H. (no condensation)
Air pressure
540 hPa to 1060 hPa
Chapter 5 Specifications
21
Transportation/
Storage
Environmental
Requirements
Temperature
-20˚C to 60˚C (32˚F to 95˚F)
Humidity
10% to 90% R.H. (no condensation)
Air pressure
200 hPa to 1060 hPa
5-2. Main Default Settings
CAL Switch Mode: The factory default display setting is DICOM mode.
Mode
Brightness
Temperature
Gamma value
Hybrid Gamma PXL
1-DICOM
400 cd/m
2
7500K
DICOM
Off
2-CAL1
400 cd/m2
7500K
2.2
Off
3-CAL2
2
7500K
DICOM
Off
7500K
2.2
- (Disable)
sRGB
sRGB
- (Disable)
6500K
2.2
- (Disable)
300 cd/m
2
4-Custom
Approx. 300 cd/m
5-sRGB
Approx. 250 cd/m2
6-Text
Approx. 100 cd/m
2
Others
Picture Expansion
Dot by Dot
Auto Input Detection
Off
Power Save
High
Indicator
4
Presence Sensor
Off
Languages
English
*1
Off
On-Screen Logo
*1
Image Rotation
Portrait
DDC*1
Auto
DC5V Output
*1
Off
*1
Off
DP Power Save
Grayscale Warning*1
Sharpness Recovery
On
*1
*1
DisplayPort version
On
1.2
*1 These menus cannot be initialized with “Monitor Reset”. (Refer to the Setup manual (on the CD-ROM)).
22
Chapter 5 Specifications
5-3. Dimensions
(600.5)
30˚
78
45
5˚
70˚
(267)
(17.7)
(130.5)
100
(130.5)
(182.5)
361
325.6
(15.7)
(17.7)
4xM4
100
(182.5)
90
13
17.5
(15.7)
(430.5-520.5)
433.6
465
(482.5-572.5)
˚
90
281
32.5
200
5-4. Accessories
Calibration Kit
Network QC Management Software
Cleaning Kit
LCD protection panel
EIZO “RadiCS UX1” Ver. 4.4.2 or later
EIZO “RadiCS Version Up Kit” Ver. 4.4.2 or later
EIZO “RadiNET Pro” Ver. 4.4.2 or later
EIZO “RadiNET Pro Lite” Ver. 4.4.2 or later
EIZO “ScreenCleaner”
EIZO "RP-915"
For the latest information about the accessories and information about the latest compatible graphics
board, refer to our web site. http://www.eizoglobal.com
Chapter 5 Specifications
23
English
Unit: mm
Chapter 6 Glossary
Daisy-chain connection
A method of connecting two or more monitors to a PC in a daisy-chain.
DDC (Display Data Channel)
VESA provides the standardization for the interactive communication of the setting information, etc.
between a PC and the monitor.
DICOM (Digital Imaging and Communication in Medicine)
The DICOM standard was developed by the American College of Radiology and the National
Electrical Manufacturer’s Association of the USA.
The DICOM compatible device connection enables to transfer the medical image and information.
The DICOM, Part 14 document defines the digital, grayscale medical image display.
DisplayPort
This is the interface standard for image signals standardized in accordance with VESA. It was
developed with the aim of replacing the conventional DVI and analog interfaces, and it can transmit
high resolution signals and sound signals, which DVI does not support. The standard size and mini
size connectors have been standardized.
DVI (Digital Visual Interface)
DVI is a digital interface standard. DVI allows direct transmission of the PC’s digital data without
loss.
This adopts the TMDS transmission system and DVI connectors. There are two types of DVI
connectors. One is a DVI-D connector for digital signal input only. The other is a DVI-I connector
for both digital and analog signal inputs.
DVI DMPM (DVI Digital Monitor Power Management)
DVI DMPM is a digital interface power saving function. The “Monitor ON (operating mode)” and
“Active Off (power saving mode)” are indispensable for DVI DMPM as the monitor’s power mode.
Gain
This is used to adjust each color parameter for red, green and blue. An LCD monitor displays the
color by the light passing through the panel color filter. Red, green and blue are the three primary
colors. All the colors on the screen are displayed by combining these three colors. The color tone
can be changed by adjusting the light intensity (volume) passing through each color’s filter.
Gamma
Generally, the monitor brightness varies nonlinearly with the input signal level, which is called
“Gamma Characteristic”. A small gamma value produces a low-contrast image, while a large
gamma value produces a highcontrast image.
Resolution
The LCD panel consists of numerous pixels of specified size, which are illuminated to form images.
This monitor consists of horizontal 1200 pixels and 1600 vertical pixels. At a resolution of 1200×
1600 (Portrait orientation), all pixels are illuminated as a full screen (1:1).
24
Chapter 6 Glossary
sRGB (Standard RGB)
Temperature
Color temperature is a method to measure the white color tone, generally indicated in degrees
Kelvin. The screen becomes reddish at a low temperature, and bluish at a high temperature, like
the flame temperature.
5000 K: Slightly reddish white
6500 K: White referred to as daylight-balanced color
9300 K: Slightly bluish white
Chapter 6 Glossary
25
English
International standard for color reproduction and color space among peripheral devices (such as
monitors, printers, digital cameras, scanners). As a form of simple color matching for the Internet,
colors can be displayed using tones close to those of the transmission and reception devices.
Appendix
Trademark
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing, LLC in the United States and other countries.
The DisplayPort Compliance Logo and VESA are registered trademarks of the Video Electronics
Standards Association.
Acrobat, Adobe, Adobe AIR, and Photoshop are registered trademarks of Adobe Systems Incorporated
in the United States and other countries.
AMD Athlon and AMD Opteron are trademarks of Advanced Micro Devices, Inc.
Apple, ColorSync, eMac, iBook, iMac, iPad, Mac, MacBook, Macintosh, Mac OS, PowerBook, and
QuickTime are registered trademarks of Apple Inc.
ColorMunki, Eye-One, and X-Rite are registered trademarks or trademarks of X-Rite Incorporated in the
United States and/or other countries.
ColorVision and ColorVision Spyder2 are registered trademarks of DataColor Holding AG in the United
States.
Spyder3 and Spyder4 are trademarks of DataColor Holding AG.
ENERGY STAR is a registered trademark of the United States Environmental Protection Agency in the
United States and other countries.
GRACoL and IDEAlliance are registered trademarks of International Digital Enterprise Alliance.
Linux is a registered trademark of Linus Torvalds.
NEC is a registered trademark of NEC Corporation.
PC-9801 and PC-9821 are trademarks of NEC Corporation.
NextWindow is a trademark of NextWindow Ltd.
Intel, Intel Core, Pentium, and Thunderbolt are trademarks of Intel Corporation in the U.S. and/or other
countries.
PowerPC is a registered trademark of International Business Machines Corporation.
PlayStation is a registered trademark of Sony Computer Entertainment Inc.
PSP and PS3 are trademarks of Sony Computer Entertainment Inc.
RealPlayer is a registered trademark of RealNetworks, Inc.
Red Hat is a registered trademark of Red Hat, Inc.
TouchWare is a trademark of 3M Touch Systems, Inc.
Windows, Windows Media, Windows Vista, SQL Server, Xbox 360, and Internet Explorer are registered
trademarks of Microsoft Corporation in the United States and other countries.
YouTube is a registered trademark of Google Inc.
Firefox is a registered trademark of the Mozilla Foundation.
Kensington and MicroSaver are registered trademarks of ACCO Brands Corporation.
EIZO, the EIZO Logo, ColorEdge, DuraVision, FlexScan, FORIS, RadiCS, RadiForce, RadiNET, Raptor,
and ScreenManager are registered trademarks of EIZO Corporation in Japan and other countries.
ColorNavigator, EcoView NET, EIZO EasyPIX, EIZO Monitor Configurator, EIZO ScreenSlicer, G-Ignition,
i • Sound, Re/Vue, Screen Administrator and UniColor Pro are trademarks of EIZO Corporation.
All other company and product names are trademarks or registered trademarks of their respective
owners.
26
Appendix
License / Copyright
Medical Standard
• It shall be assured that the final system is in compliance to IEC60601-1-1 requirement.
• Power supplied equipment can emit electromagnetic waves, that could influence, limit or result in
malfunction of the monitor. Install the equipment in a controlled environment, where such effects
are avoided.
Classification of Equipment
------
Type of protection against electric shock : Class I
EMC class: EN60601-1-2:2015 Group 1 Class B
Classification of medical device (MDD 93/42/EEC): Class I
Mode of operation : Continuous
IP Class : IPX0
Appendix
27
English
A round gothic bold bit map font designed by Ricoh is used for the characters displayed on this product.
EMC Information
The RadiForce series has a performance that appropriately displays images.
Environments of Intended Use
The RadiForce series is intended to be used in Professional healthcare facility environments such as
clinics and hospitals.
The following environments are not suitable for the RadiForce series to be used:
• Home healthcare environments
• In the vicinity of high-frequency surgical equipments such as electrosurgical knives
• In the vicinity of short-wave therapy equipments
• RF shielded room of the medical equipment systems for MRI
• In shielded location Special environments
• Installed in vehicles including ambulances.
• Other special environment
WARNING
The RadiForce series requires special precautions regarding EMC and need to be installed. You
need to carefully read EMC Information and the “PRECAUTIONS” section in this document, and observe the following instructions when installing and operating the product.
The RadiForce series should not be used adjacent to or stacked with other equipment. If adjacent
or stacked use is necessary, the equipment or system should be observed to verify normal operation in the configuration in which it will be used.
When using a portable RF communication equipment, keep it 30 cm (12 inches) or more away from
any part, including cables, of the RadiForce series. Otherwise, degradation of the performance of
this equipment could result.
Anyone who connects additional equipment to the signal input part or signal output parts, configuring a medical system, is responsible that the system complies with the requirements of IEC/
EN60601-1-2.
Be sure to use the cables attached to the product, or cables specified by EIZO.
Use of cables other than those specified or provided by EIZO of this equipment could result in increased electromagnetic emissions or decreased electromagnetic immunity of this equipment and
improper operation.
Cables
EIZO Designated
Cables
Max.
Cable Length
Shielding
Ferrite Core
Signal cable (DisplayPort)
PP300 / PP200
3m
Shielded
With Ferrite Cores
Signal cable (DVI-D)
DD300 / FD-C39
3m
Shielded
With Ferrite Cores
USB cable
UU300 / MD-C93
3m
Shielded
With Ferrite Cores
Power cord (with earth)
-
3m
Unshielded
Without Ferrite Cores
28
Appendix
Technical Descriptions
Electromagnetic emissions
Emission test
Compliance
Electromagnetic environment - Guidance
RF emissions
CISPR11 / EN55011
Group 1
The RadiForce series uses RF energy only for its internal function.
Therefore, its RF emission are very low and are not likely to cause any interference in
nearby electronic equipment.
RF emissions
CISPR11 / EN55011
Class B
Harmonic emissions
IEC / EN61000-3-2
Class D
The RadiForce series is suitable for use in all establishments, including domestic
establishments and those directly connected to the public low-voltage power supply
network that supplies buildings used for domestic purposes.
Voltage fluctuations /
flicker emissions
IEC / EN61000-3-3
Complies
Electromagnetic immunity
The RadiForce series has been tested at the following compliance levels according to the testing requirements for
professional healthcare facility environments defined in IEC / EN60601-1-2.
Customers and users of the RadiForce series must ensure that the RadiForce series is used in the following
environments:
Immunity test
Test level for
professional
healthcare facility
environments
Compliance level
Electromagnetic environment Guidance
Electrostatic
discharge (ESD)
IEC / EN61000-4-2
±8 kV contact discharge
±15 kV air discharge
±8 kV contact discharge
±15 kV air discharge
Floors should be wood, concrete or ceramic tile.
If floors are covered with synthetic material, the
relative humidity should be at least 30%.
Electrical fast
transients / bursts
IEC / EN61000-4-4
±2 kV power lines
±1 kV input / output lines
±2 kV power lines
±1 kV input / output lines
Mains power quality should be that of a typical
commercial or hospital environment.
Surges
IEC / EN61000-4-5
±1 kV line to line
±2 kV line to ground
±1 kV line to line
±2 kV line to ground
Mains power quality should be that of a typical
commercial or hospital environment.
Voltage dips, short
interruptions and
voltage variations on
power supply input
lines
IEC / EN61000-4-11
0 % UT (100 % dip in UT)
0.5 cycles and 1 cycle
70 % UT (30 % dip in UT)
25 cycles
0 % UT (100 % dip in UT)
5 sec
0 % UT (100 % dip in UT)
0.5 cycles and 1 cycle
70 % UT (30 % dip in UT)
25 cycles
0 % UT (100 % dip in UT)
5 sec
Mains power quality should be that of a typical
commercial or hospital environment. If the user
of the RadiForce series requires continued
operation during power mains interruptions, it
is recommended that the RadiForce series be
powered from an uninterruptible power supply
or a battery.
Power frequency
magnetic fields
IEC / EN61000-4-8
30 A/m
(50 / 60 Hz)
30 A/m
Power frequency magnetic fields should be at
levels characteristic of a typical location in a
typical commercial or hospital environment. The
product should be kept at least 15 cm away
from the source of power frequency magnetic
fields during use.
Appendix
29
English
The RadiForce series is intended for use in the electromagnetic environment specified below.
The customer or the user of the RadiForce series should assure that it is used in such an environment.
Electromagnetic immunity
The RadiForce series has been tested at the following compliance levels according to the testing requirements for
professional healthcare facility environments defined in IEC / EN60601-1-2.
Customers and users of the RadiForce series must ensure that the RadiForce series is used in the following
environments:
Immunity test
Test level for
professional
healthcare facility
environments
Compliance level
Electromagnetic environment Guidance
Portable and mobile RF communications
equipment should be used no closer to any
part of the RadiForce series, including cables,
than the recommended separation distance
calculated from the equation applicable to the
frequency of the transmitter.
Recommended separation distance
Conducted
3 Vrms
disturbances induced 150 kHz - 80 MHz
by RF fields
IEC / EN61000-4-6
Radiated RF fields
IEC / EN61000-4-3
3 Vrms
6 Vrms
ISM bands between
150 kHz and 80 MHz
6 Vrms
3 V/m
80 MHz - 2.7 GHz
3 V/m
d = 1.2√P
d = 1.2√P, 80 MHz - 800 MHz
d = 2.3√P, 800 MHz - 2.7 GHz
Where “P” is the maximum output power rating
of the transmitter in watts (W) according to
the transmitter manufacturer and “d” is the
recommended separation distance in meters
(m).
Field strengths from fixed RF transmitters, as
determined by an electromagnetic site survey
a)
, should be less than the compliance level in
each frequency range b).
Interference may occur in the vicinity of
equipment marked with the following symbol.
Note 1
UT is the a.c. mains voltage prior to application of the test level.
Note 2
At 80 MHz and 800 MHz, the higher frequency range applies.
Note 3
Guidelines regarding conducted disturbances induced by RF fields or radiated RF fields may not apply in all
situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.
Note 4
The ISM bands between 150 kHz and 80 MHz are 6.765 MHz to 6.795 MHz, 13.553 MHz to 13.567 MHz, 26.957
MHz to 27.283 MHz, and 40.66 MHz to 40.70 MHz.
a)
Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile
radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy.
To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be
considered. If the measured field strength in the location in which the RadiForce series is used exceeds the applicable
RF compliance level above, the RadiForce series should be observed to verify normal operation. If abnormal
performance is observed, additional measures may be necessary, such as reorienting or relocating the RadiForce series.
b)
Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.
30
Appendix
Recommended separation distances between portable or mobile RF communication equipment
and the RadiForce Series
Test
Bandwidth a)
frequency
(MHz)
(MHz)
Service a)
Modulation b)
Minimum
IEC /
Maximum
Compliance
separation EN60601
power
level
distance test level
(W)
(V/m)
(m)
(V/m)
385
380 - 390
TETRA 400
Pulse modulation b) 1.8
18 Hz
0.3
27
27
450
430 - 470
GMRS 460,
FRS 460
FM
±5 kHz deviation
1 kHz sine
0.3
28
28
710
704 - 787
LTE Band 13, 17
Pulse modulation b) 0.2
217 Hz
0.3
9
9
800 - 960
GSM 800 / 900,
TETRA 800,
iDEN 820
CDMA 850,
LTE Band 5
Pulse modulation b) 2
18 Hz
0.3
28
28
1700 - 1990
Pulse modulation b) 2
GSM 1800;
CDMA 1900;
217 Hz
GSM 1900;
DECT;
LTE Band 1, 3, 4,
25;
UMTS
0.3
28
28
2450
2400 - 2570
Bluetooth,
WLAN,
802.11 b/g/n,
RFID 2450,
LTE Band 7
Pulse modulation b) 2
217 Hz
0.3
28
28
5240
5100 - 5800
WLAN 802.11 a/n Pulse modulation b) 0.2
217 Hz
0.3
9
9
745
2
780
810
870
930
1720
1845
1970
5500
5785
a)
For some services, only the uplink frequencies are included.
b)
Carrier waves are modulated using a 50 % duty cycle square wave signal.
Appendix
31
English
The RadiForce series is intended for use in an electromagnetic environment in which radiated RF disturbances
are controlled. The customer or the user of the RadiForce series can help prevent electromagnetic interference by
maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the
RadiForce series.
Immunity to proximity fields from following RF wireless communication equipments has been confirmed:
The RadiForce series is intended for use in an electromagnetic environment in which radiated RF disturbances are
controlled. For other portable and mobile RF communication equipments (transmitters), minimum distance between
portable and mobile RF communications equipment (transmitters) and the RadiForce series as recommended below,
according to the maximum output power of the communications equipment.
Rated maximum
output power of
transmitter
(W)
Separation distance according to frequency of transmitter
(m)
150 kHz to 80 MHz
d = 1.2√P
80 MHz to 800 MHz
d = 1.2√P
800 MHz to 2.7 GHz
d = 2.3√P
0.01
0.12
0.12
0.23
0.1
0.38
0.38
0.73
1
1.2
1.2
2.3
10
3.8
3.8
7.3
100
12
12
23
For transmitters rated at a maximum output power not listed above, the recommended separation distance “d” in meters (m)
can be estimated using the equation applicable to the frequency of the transmitter, where “P” is the maximum output power
rating of the transmitter in watts (W) according to the transmitter manufacturer.
Note 1
At 80 MHz and 800 MHz, the separation distance for a higher frequency range applies.
Note 2
These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.
32
Appendix
FCC Declaration of Conformity
English
For U.S.A. , Canada, etc. (rated 100-120 Vac) Only
FCC Declaration of Conformity
We, the Responsible Party
EIZO Inc.
5710 Warland Drive, Cypress, CA 90630
Phone: (562) 431-5011
declare that the product
Trade name: EIZO
Model: RadiForce RX250
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures.
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
* Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Note
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep
interference within the limits of a Class B digital device.
- AC Cord
- Shielded Signal Cable (enclosed)
Canadian Notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.
Appendix
33
English
Recycling Information/Informationen zum Thema Recycling/
Informations sur le recyclage/Сведения по утилизации
Recycling Information
For recycling information for customers in Switzerland, please refer to the following website.
http://www.swico.ch
Deutsch
This product, when disposed of, is supposed to be collected and recycled according to your country’s
legislation to reduce environmental burden. When you dispose of this product, please contact a distributor or
an affiliate in your country.
The contact addressees are listed on the EIZO website below.
http://www.eizoglobal.com
Informationen zum Thema Recycling
Русский
Kunden in der Schweiz entnehmen Informationen zum Recycling der folgenden Website:
http://www.swico.ch
Français
Dieses Produkt muss gemäß den Vorschriften Ihres Landes zur Entlastung der Umwelt recyclet werden.
Wenden Sie sich bei der Entsorgung dieses Produkts an einen Verteiler oder eine Tochtergesellschaft in
Ihrem Land.
Die Adressen zur Kontaktaufnahme sind auf der unten angegebenen Website von EIZO aufgeführt.
http://www.eizoglobal.com
Informations sur le recyclage
Ce produit doit être jeté aux points de collecte prévus à cet effet et recyclé conformément à la législation de
votre pays, afin de réduire l’impact sur l’environnement. Lorsque vous jetez ce produit, veuillez contacter un
distributeur ou une société affiliée de votre pays.
Les adresses des distributeurs sont répertoriées sur le site Web EIZO ci-dessous.
http://www.eizoglobal.com
Pour les clients en Suisse, veuillez consulter le site Web suivant afin d’obtenir des informations sur le
recyclage.
http://www.swico.ch
Información sobre reciclaje
Este producto debe desecharse y reciclarse según la legislación del país para reducir el impacto
medioambiental. Cuando desee deshacerse de este producto, póngase en contacto con un distribuidor o
una filial de su país.
Encontrará las direcciones de contacto en el sitio web de EIZO que se indica a continuación.
http://www.eizoglobal.com
Informazioni sul riciclaggio
Per lo smaltimento e il riciclaggio del presente prodotto, attenersi alle normative vigenti nel proprio paese per
ridurre l’impatto ambientale. Per lo smaltimento, rivolgersi ad un distributore o un affiliato presenti nel proprio
paese.
Gli indirizzi sono elencati nel sito Web EIZO riportato di seguito.
http://www.eizoglobal.com
Per informazioni sul riciclaggio per i clienti in Svizzera, consultare il sito Web riportato di seguito.
http://www.swico.ch
Återvinningsinformation
När denna produkt kasseras ska den hanteras och återvinnas enligt landets föreskrifter för att reducera
miljöpåverkan. När du kasserar produkten ska du kontakta en distributör eller representant i ditt land.
Kontaktadresserna listas på EIZO-webbplatsen nedan.
http://www.eizoglobal.com

i
Πληροφορίες ανακύκλωσης
Το προϊόν αυτό, όταν απορρίπτεται, πρέπει να συλλέγεται και να ανακυκλώνεται σύμφωνα με τη νομοθεσία
της χώρας σας έτσι ώστε να μην επιβαρύνει το περιβάλλον. Για να απορρίψετε το προϊόν, επικοινωνήστε με
έναν αντιπρόσωπο ή μια θυγατρική εταιρεία στη χώρα σας.
Οι διευθύνσεις επικοινωνίας αναγράφονται στην τοποθεσία web της EIZO παρακάτω.
http://www.eizoglobal.com
Сведения по утилизации
По истечении срока службы данного продукта его следует принести на сборный пункт и
утилизировать в соответствии с действующими предписаниями в вашей стране, чтобы уменьшить
вредное воздействие на окружающую среду. Прежде чем выбросить данный продукт, обратитесь к
дистрибьютору или в местное представительство компании в вашей стране.
Контактные адреса можно найти на веб-узле EIZO.
http://www.eizoglobal.com
Informatie over recycling
Wanneer u dit product wilt weggooien, moet het uit milieu-overwegingen worden verzameld en gerecycled
volgens de betreffende wetgeving van uw land. Wanneer u dit product wilt weggooien, moet u contact
opnemen met een distributeur of een partner in uw land.
De contactadressen worden vermeld op de volgende EIZO-website.
http://www.eizoglobal.com
Informação sobre reciclagem
Este produto, quando o deitar fora, deve ser recolhido e reciclado de acordo com a legislação do seu país
para reduzir a poluição. Quando deitar fora este produto, contacte um distribuidor ou uma filial no seu país.
Os endereços de contacto estão listados no website do EIZO, abaixo.
http://www.eizoglobal.com
Oplysninger om genbrug
Dette produkt forventes ved bortskaffelse at blive indsamlet og genbrugt i overensstemmelse med
lovgivningen i dit land for at reducere belastningen af miljøet. Når du bortskaffer denne produkt, skal du
kontakte en distributør eller et tilknyttet selskab i dit land.
Adresserne på kontaktpersonerne er angivet på EIZO’s websted nedenfor.
http://www.eizoglobal.com
Kierrätystä koskevia tietoja
Tuote tulee hävittää kierrättämällä maan lainsäädännön mukaisesti ympäristön kuormittumisen
vähentämiseksi. Kun hävität tuotteen, ota yhteyttä jälleenmyyjään tai tytäryhtiöön maassasi.
Yhteystiedot löytyvät EIZOn Internet-sivustolta.
http://www.eizoglobal.com
Wykorzystanie surowców wtórnych
Ten produkt po zużyciu powinien być zbierany i przetwarzany zgodnie z krajowymi przepisami dotyczącymi
ochrony środowiska. Wyrzucając ten produkt, należy skontaktować się z lokalnym dystrybutorem lub
partnerem. Adresy kontaktowe można znaleźć we wskazanej poniżej witrynie internetowej firmy EIZO.
http://www.eizoglobal.com
ii

Informace o recyklaci
Ringlussevõtu alane teave
Újrahasznosítási információ
Français
Jelen terméket, amikor eldobjuk, az illető ország törvényei alapján kell összegyűjteni és újrahasznosítani,
hogy csökkentsük a környezet terhelését. Amikor ezt a terméket eldobja, kérjük lépjen kapcsolatba egy
országon belüli forgalmazóval vagy társvállalkozással.
A kapcsolat címei az EIZO alábbi weboldalán találhatók felsorolva:
http://www.eizoglobal.com
Deutsch
Keskkonnakoormuse vähendamiseks tuleks kasutatud tooted kokku koguda ja võtta ringlusse vastavalt teie
riigi seadustele. Kui kõrvaldate käesoleva toote, võtke palun ühendust turustaja või filiaaliga oma riigis.
Kontaktisikud on toodud EIZO veebilehel järgmisel aadressil:
http://www.eizoglobal.com
English
Při likvidaci produktu musí být produkt vyzvednut a recyklován podle zákonů příslušné země, aby
nedocházelo k zatěžování životního prostředí. Zbavujete-li se produktu, kontaktujte distributora nebo
pobočku ve své zemi. Kontaktní adresy jsou uvedeny na následující webové stránce společnosti EIZO.
http://www.eizoglobal.com
Podatki o recikliranju
Informácie o recyklácii
Pri likvidácii musí byť tento výrobok recyklovaný v súlade s legislatívou vašej krajiny, aby sa znížilo zaťaženie
životného prostredia. Keď sa chcete zbaviť tohto výrobku, kontaktujte prosím distribútora alebo pobočku vo
vašej krajine.
Zoznam kontaktných adries je uvedený na nasledovnej webovej stránke firmy EIZO:
http://www.eizoglobal.com
Pārstrādes informācija
Utilizējot šo produktu, tā savākšana un pārstrāde veicama atbilstoši jūsu valsts likumdošanas prasībām
attiecībā uz slodzes uz vidi samazināšanu. Lai veiktu šī produkta utilizāciju, sazinieties ar izplatītāju vai
pārstāvniecību jūsu valstī.
Kontaktadreses ir norādītas zemāk minētajā EIZO tīmekļa vietnē.
http://www.eizoglobal.com
Informacija apie grąžinamąjį perdirbimą
Šalinant (išmetant) šiuos gaminius juos reikia surinkti ir perdirbti grąžinamuoju būdu pagal jūsų šalies teisės
aktus, siekiant sumažinti aplinkos teršimą. Kai reikia išmesti šį gaminį, kreipkitės į jūsų šalyje veikiančią
gaminių pardavimo atstovybę arba jos filialą.
Kontaktiniai adresatai nurodyti EIZO interneto svetainėje.
http://www.eizoglobal.com

iii
Русский
Ob koncu uporabe odslužen izdelek izročite na zbirno mesto za recikliranje v skladu z okoljevarstveno
zakonodajo vaše države. Prosimo, da se pri odstranjevanju izdelka obrnete na lokalnega distributerja ali
podružnico.
Kontaktni naslovi so objavljeni na spodaj navedenih spletnih straneh EIZO:
http://www.eizoglobal.com
Информация относно рециклиране
При изхвърлянето на този продукт се предлага събирането и рециклирането му съобразно законите на
вашата страна за да се намали замърсяването на околната среда. Когато искате да се освободите от
този продукт, моля свържете се с търговския му представител или със съответните органи отговарящи
за това във вашата страна.
Данните за връзка с нас са описани на следния Интернет сайт на EIZO:
http://www.eizoglobal.com
Informaţie referitoare la reciclare
Acest produs, când debarasat, trebuie colectat şi reciclat conform legislaţiei ţării rspective ca să reducem
sarcina mediului. Când se debarasează de acest produs, vă rugăm să contactaţi un distribuitor sau un afiliat
al ţării respective.
Adresele de contact le găsiţi pe pagina de web al EIZO:
http://www.eizoglobal.com
http://www.eizoglobal.com
Geri Dönüşüm Bilgisi
Bu ürünün, atılacağı zaman, ülkenizin çevre kirliliğinin azaltılması konusundaki mevzuatına göre toplanması
ve yeniden değerlendirilmesi gerekmektedir. Ürünü atacağınız zaman lütfen ülkenizdeki bir distribütör veya
ilgili kuruluşla temasa geçiniz.
İrtibat adresleri aşağıdaki EIZO web sitesinde verilmiştir.
http://www.eizoglobal.com
iv

153 Shimokashiwano, Hakusan, Ishikawa 924-8566 Japan
中国苏州市苏州工业园区展业路 8 号中新科技工业坊 5B
Carl-Benz-Straße 3, 76761 Rülzheim, Germany
http://www.eizoglobal.com
Copyright © 2016-2019 EIZO Corporation. All rights reserved.
00N0L952E1
IFU-RX250-5
5th Edition-May, 2019 Printed in Japan.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising