Eizo | PCSK-03 | User manual | Eizo PCSK-03 User Manual

Eizo PCSK-03 User Manual
User’s Manual
Preparation
Introduction
This User’s Manual explains the procedure to install a PC compatible with PCSK-03. For information about
how to mount PCSK-03 on a monitor after a PC is installed, refer to User’s Manual (Basics) that comes with
this product.
Compatible PCs
•• Hewlett-Packard HP t520 Thin Client (P.3)
•• Hewlett-Packard HP t310 Zero Client (P.4)
•• Hewlett-Packard HP Z2 Mini G3 Workstation (P.5)
•• Dell Wyse T10 / P25 (P.6)
•• Dell Wyse D10D / D10DP (P.7)
Hewlett-Packard and HP are registered trademarks of Hewlett-Packard Company in the United States.
Dell is a registered trademark of Dell Inc. in the United States.
Wyse is a registered trademark of Dell Inc. in the United States.
TORX is a registered trademark of Acument Intellectual Properties, LLC.
EIZO and the EIZO Logo are registered trademarks of EIZO Corporation in Japan and other countries.
All other company and product names are trademarks or registered trademarks of their respective owners.
2
Attachment procedure
●● Hewlett-Packard HP t520 Thin Client
Parts required
•• Screws: M4x8 (Attached to PCSK-03, four pcs.)
Tools required
•• Phillips screwdriver (#2)
•• TORX driver (T10)
Position of a screw hole (four positions)
HP t520 Thin Client*1
*1 Before installing A, remove the four TORX
screws attached to the client terminal side
of the PC.
A
Screws: M4x8
(Attached to PCSK-03,
four positions)
3
●● Hewlett-Packard HP t310 Zero Client
Parts required
•• F7X24AA (Optional mounting bracket for HP)
•• Screws (Attached to F7X24AA, four pcs.)
•• Nuts (Attached to F7X24AA, four pcs.)
Tools required
•• Phillips screwdriver (#2)
•• Box driver (7mm)
Position of a screw hole (four positions)
HP t310 Zero Client
A
F7X24AA
Screws (Attached to
F7X24AA, four positions)
4
Nuts (Attached to
F7X24AA, four positions)
●● Hewlett-Packard HP Z2 Mini G3 Workstation
Parts required
•• Screws: M4x8 (Attached to PCSK-03, four pcs.)
Tools required
•• Phillips screwdriver (#2)
Position of a screw hole (four positions)
HP Z2 Mini G3 Workstation*1
*1 Before installing A, remove four rubber feet
attached to the client terminal side of the
PC.
A
Screws: M4x8
(Attached to PCSK-03,
four positions)
Note
•• You can also install the client terminal in the orientations shown below.
5
●● Dell Wyse T10 / P25
Parts required
•• Mounting bracket (Attached to Wyse T10 / P25)
•• Screws: M4x8 (Attached to PCSK-03, four pcs.)
Tools required
•• Phillips screwdriver (#2)
Position of a screw hole (four positions)
Wyse T10 / P25
A
Mounting bracket
Screws: M4x8
(Attached to PCSK-03,
four positions)
6
●● Dell Wyse D10D / D10DP
Parts required
•• Screws: M4x8 (Attached to PCSK-03, four pcs.)
Tools required
•• Phillips screwdriver (#2)
Position of a screw hole (four positions)
Wyse D10D / D10DP*1
* 1 Before installing A, remove four screws
attached to the client terminal side of
the PC.
A
Screws: M4x8
(Attached to PCSK-03,
four positions)
7
3rd Edition-July, 2017
Copyright © 2016-2017 EIZO Corporation. All rights reserved.
03V26736C1
(UM-PCSK-03-2-AL)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising