Eizo | RP-917 | User manual | Eizo RP-917 User Manual

Eizo RP-917 User Manual
User's Manual
Panel Protector for EIZO 54.1 cm (21.3) inch class LCD Monitors
Note
•• Surface of the panel protector catches the dirt (dust or finger prints) easily. Please use the enclosed gloves
while installing and removing the panel protector.
•• Please use the supplied masking tape and be careful not to scratch the LCD panel or the cabinet with the panel
protector during installation. Also please do not remove the panel protector often. It may scratch or result in
damage to the LCD panel.
•• When using LCD monitor with optional panel protector, it is preferable to avoid using downwards. In this
condition, the panel protector might become bend or slip out from the monitor.
•• If using the Integrated Front Sensor after installation of a panel protector, be sure to execute correlation using
RadiCS/RadiCS LE. Refer to each User’s Manual for details.
●●Installation
Before installation, please remove dust and stains from the LCD panel.
1.
Tape
2.
Separator
Cut
(2)
Tape (blue)
(1)
1.
3.
Lever
Strip the tape from the separator and adhere it on each edge of the cabinet (on the right and left).
Adhere the tape on long sides of the cabinet.
2. Set the panel protector into the grooves of the panel frame; the lower first (1), then the upper (2).
The panel protector has a cut to fit on the sensor. Align the cut with the sensor position when installing the panel
protector. If installed in the wrong orientation, the sensor may be damaged.
3. With the enclosed tool (Lever) set the tabs of the panel protector into the side grooves (4 tabs).
Put the lever on the tabs of the panel protector and move it toward the LCD panel to install. Position the
protector into the LCD panel tightly without leaving an opening.
4. Strip the tape from the cabinet.
●●Removing
Put the lever on the tabs of panel protector and move it toward the cabinet to remove.
●●Cleaning
This product comes with a special cleaning cloth designed to remove stains from the panel.
If necessary stubborn stains can be removed by moistening part of the cloth with water to enhance its
cleaning power.
Note
•• Please be sure to keep the panel protector immobilized while cleaning it. Otherwise it may scratch the surface
of the LCD panel. To hold the panel protector by hand, use gloves or a soft cloth to avoid dust or finger prints.
•• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the
cabinet or panel, and also quality deterioration of the image.
•• Never use any solvents or chemicals, such as thinner, benzene, wax, and abrasive cleaner, which may damage
the cabinet or panel.
153 Shimokashiwano, Hakusan, Ishikawa 924-8566 Japan
Phone: +81 76 277 6792 Fax: +81 76 277 6793
Tips
•• The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface.
●●Specification
Helmut-Grashoff-Strasse 18, 41179 Mönchengladbach, Germany
Phone: +49 2161 8210210 Fax: +49 2161 8210150
〒 924-8566
Surface treatment
Reflectivity
Dimension/ Weight
Accessories
石川県白山市下柏野町 153 番地
http://www.eizoglobal.com
http://www.eizo.co.jp
Copyright © 2016 EIZO Corporation. All rights reserved.
1st Edition-September, 2016 Printed in Japan.
00N0L965A1
(UM-RP-917-AL)
Anti-Reflective Coating (Both sides)
Coating strength
4H
Less than 1 %
Light transmission More than 95.0 %
341.5 mm (W) × 425.7 mm (H) × 1.2 mm (D) / Approx. 210 g
Lever (for Panel Protector), Gloves, Cleaning Cloth, User’s Manual, Masking tape 4 pieces (2 sets)
User's Manual
Panel Protector for EIZO 54.1 cm (21.3) inch class LCD Monitors
Note
•• Surface of the panel protector catches the dirt (dust or finger prints) easily. Please use the enclosed gloves
while installing and removing the panel protector.
•• Please use the supplied masking tape and be careful not to scratch the LCD panel or the cabinet with the panel
protector during installation. Also please do not remove the panel protector often. It may scratch or result in
damage to the LCD panel.
•• When using LCD monitor with optional panel protector, it is preferable to avoid using downwards. In this
condition, the panel protector might become bend or slip out from the monitor.
•• If using the Integrated Front Sensor after installation of a panel protector, be sure to execute correlation using
RadiCS/RadiCS LE. Refer to each User’s Manual for details.
●●Installation
Before installation, please remove dust and stains from the LCD panel.
1.
Tape
2.
Separator
Cut
(2)
Tape (blue)
(1)
1.
3.
Lever
Strip the tape from the separator and adhere it on each edge of the cabinet (on the right and left).
Adhere the tape on long sides of the cabinet.
2. Set the panel protector into the grooves of the panel frame; the lower first (1), then the upper (2).
The panel protector has a cut to fit on the sensor. Align the cut with the sensor position when installing the panel
protector. If installed in the wrong orientation, the sensor may be damaged.
3. With the enclosed tool (Lever) set the tabs of the panel protector into the side grooves (4 tabs).
Put the lever on the tabs of the panel protector and move it toward the LCD panel to install. Position the
protector into the LCD panel tightly without leaving an opening.
4. Strip the tape from the cabinet.
●●Removing
Put the lever on the tabs of panel protector and move it toward the cabinet to remove.
●●Cleaning
This product comes with a special cleaning cloth designed to remove stains from the panel.
If necessary stubborn stains can be removed by moistening part of the cloth with water to enhance its
cleaning power.
Note
•• Please be sure to keep the panel protector immobilized while cleaning it. Otherwise it may scratch the surface
of the LCD panel. To hold the panel protector by hand, use gloves or a soft cloth to avoid dust or finger prints.
•• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the
cabinet or panel, and also quality deterioration of the image.
•• Never use any solvents or chemicals, such as thinner, benzene, wax, and abrasive cleaner, which may damage
the cabinet or panel.
153 Shimokashiwano, Hakusan, Ishikawa 924-8566 Japan
Phone: +81 76 277 6792 Fax: +81 76 277 6793
Tips
•• The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface.
●●Specification
Helmut-Grashoff-Strasse 18, 41179 Mönchengladbach, Germany
Phone: +49 2161 8210210 Fax: +49 2161 8210150
〒 924-8566
Surface treatment
Reflectivity
Dimension/ Weight
Accessories
石川県白山市下柏野町 153 番地
http://www.eizoglobal.com
http://www.eizo.co.jp
Copyright © 2016 EIZO Corporation. All rights reserved.
1st Edition-September, 2016 Printed in Japan.
00N0L965A1
(UM-RP-917-AL)
Anti-Reflective Coating (Both sides)
Coating strength
4H
Less than 1 %
Light transmission More than 95.0 %
341.5 mm (W) × 425.7 mm (H) × 1.2 mm (D) / Approx. 210 g
Lever (for Panel Protector), Gloves, Cleaning Cloth, User’s Manual, Masking tape 4 pieces (2 sets)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising