Pro-Ject | Juke Box S2 Stereo Set | manual | Pro-Ject Juke Box S2 Stereo Set Manual

Pro-Ject Juke Box S2 Stereo Set Manual
INSTRUCTIONS FOR USE
Pro-Ject Jukebox S2
2
© Pro-Ject Audio Systems · Pro-Ject Jukebox S2 · Revision 2018.04.04
Jukebox S2
Controls, features and connections
(1)
TURNTABLE MOTOR SWITCH
(2)
AMPLIFIER ON/OFF SWITCH
(3)
REMOTE CONTROL
(4)
INPUT SELECTOR, VOLUME CONTROL
(5)
PLATTER
(6)
DRIVE BELT
(7)
STEPPED DRIVE PULLEY
(8)
TONEARM COUNTERWEIGHT
(9)
TONEARM TUBE
(10)
TONEARM REST AND REMOVABLE TRANSPORT LOCK
(11)
TONEARM LIFT LEVER
(12)
HEADSHELL WITH FINGER LIFT
(13)
TURNTABLE DISPLAY
(14)
EARTH CONNECTION
(15)
PHONO OUT
(16)
LINE IN
(17)
VAR OUT
(18)
FIX OUT
(19)
BLUETOOTH ANTENE
(20)
SPEAKERS OUTPUT
(21)
POWER SUPPLY SOCKET
(22)
LID
(23)
LID HINGE
(24)
HINGE FASTENERS
POWER SUPPLY (NOT SHOWN) *
© Pro-Ject Audio Systems · Pro-Ject Jukebox S2 · Revision 2018.04.04
3
Dear music lover,
Thank you for purchasing a record player from Pro-Ject Audio Systems.
In order to achieve maximum performance and reliability with this record player you should study these
instructions for use carefully.
!
Warning of a hazard for the user, the unit or possible misuse
Important notice
The following instructions for adjusting the cartridge are provided in case the cartridge is replaced
different model at a later date.
During assembly and adjustment of the deck small parts could be lost if not carefully placed
suitable receptacle. Before starting assembly make get fwqmiliar with the parts listed above
correspondingly numbered in the technical drawings above. Separately packed items are marked
an asterisk *.
by a
in a
and
with
Safety instructions
The power supply is used to connect and disconnect the unit from the mains. Make sure that the
plug is easily accessible at all times. Hold the plug when unplugging the power cord. Never
handle the power cord while your hands are wet or damp.
!
Avoid letting liquids enter the device. Never place any item containing liquid, like a flower vase,
on or near the device. Never spill any liquid on the device. Never place any naked flame sources,
like lighted candles, on or near the device. The product shall not be used in damp or wet locations,
next to a bathtub, sink, swimming pool or any other similar conditions.
Keep plastic bags away from children to prevent any risk of suffocation.
Platter and drive belt installation
Please remove brown paper insert which holds the platter in transport position. Put the felt mat on the
top of the platter. Install the drive belt as shown in the following illustration.
4
© Pro-Ject Audio Systems · Pro-Ject Jukebox S2 · Revision 2018.04.04
Cartridge downforce adjustment
The counterweight (8) supplied is suitable for cartridges weighing between 3 - 7g (weight no. 81). The
counterweight is pre-set perfectly from the factory.
In case you need to set the tracking force, please read following instructions:
Place the stylus pressure gauge onto the platter. To adjust the amount of pressure, carefully move the
counterweight along the support rod, until the stylus pressure is sufficient to raise the pressure gauge
to the level position. Moving the counterweight away from the cartridge will reduce pressure and
towards will increase pressure. Finally secure the counterweight using hexagonal key provided.
If the stylus gauge becomes level, then the correct pressure has been achieved. However if the there is
insufficient or excessive pressure the gauge will either not move or tilt down.
Connectors
!
Take care to connect the left and right channels correctly. The right channel is usually marked
red, the left channel black or white.
The red speaker terminals carry the positive signal (+), the black speaker terminals the negative
signal (–). Make sure the polarity of the connection is correct at each end of the cables.
Connection to the speakers
The output terminals accept loudspeaker cables terminated with 4mm ∅ Banana plugs, spades
connectors or naked wire.
Variable output (Line output)
A power amplifier or active loudspeakers can be connected to the output sockets marked Var Out
(17).
Fixed output (Record output, connecting a headphone amplifier)
Fix Out (18) connects an analogue record device or a Pro-Ject Head Box headphone amplifier.
© Pro-Ject Audio Systems · Pro-Ject Jukebox S2 · Revision 2018.04.04
5
Phono output
To use an external phono preamplifier, connect the RCA sockets marked Phono OUT (15). The
earthing wire may be connected to the screw terminal if you encounter hum problems when using the
turntable.
Line input
Line level sources such as CD player, radio or TV can be connected to the input sockets marked Line
IN (16).
Mains power connection
Connect the low voltage plug from the power supply to the 24V socket (21) before connecting the
power supply to the mains.
Switching ON and OFF (turntable motor)
The rocker switch (1) on the bottom turns the motor of the turntable
To switch on from standby or to standby (amplifier)
The rocker switch (2) on the bottom turns the unit on or back into standby.
Control of the unit using the knob on the front
Standby
After the unit is powered on by the rocker switches on the bottom, pressing the knob for 3 seconds,
turns the unit on. For turn the unit back to standby press the knob again for 3 seconds
!
It is important to turn the unit to standby before it´s powered off by the switch on the bottom.
To not follow this step may cause damage to the speakers.
Input selector
After the unit is turned on, pressing the button in the middle selects desired input. After start
Bluetooth input is always selected. Pressing input button changes inputs in following order: Bluetooth
> Turntable > Line In. Bluetooth input gives a “beep” sound when selected. Selected input is indicated
on the top line of the display.
Volume
Adjust the volume to the desired level rotating the knob. Volume can be set in 33 steps (0-32) and is
indicated on the bottom line of the display
6
© Pro-Ject Audio Systems · Pro-Ject Jukebox S2 · Revision 2018.04.04
Remote control
red button turns the unit on or back into standby
Mute activate/deativate mute
Bass+/Bass-/Treble+/Treble- tone control
Loudness activate/deactivate Loudness
Bluetooth/Turntable/Line in direct access to
input
Volume+/Volume- adjust volume
Bluetooth connection
Bluetooth is active only when Bluetooth input is selected.
Juke Box E remembers last paired unit and reconnects automatically when available and if the
bluetooth device allows automatic reconnections.
Juke Box E doesn´t request any pairing code confirmation.
!
Only one active Bluetooth connection is possible at a time. If the unit can’t be found in
Bluetooth search window in mobile device, make sure that there is no other active Bluetooth
connection.
Bluetooth input gives 2 different “beeps”,
First appears when Bluetooth input is selected. And in case of Bluetooth device disconnects.
Second appear when Bluetooth device is found and connected.
Pairing with Android devices
Open Settings and tap on Bluetooth. Turn on Bluetooth and tap on Scan. Searched devices will show
up. Tap on "Juke Box E".
Pairing with Apple devices
Tap on Settings, tap on Bluetooth, turn on Bluetooth. Your device will automatically start searching
for available devices. Tap on "Juke Box E".
© Pro-Ject Audio Systems · Pro-Ject Jukebox S2 · Revision 2018.04.04
7
Fitting the lid
Fit the lid (dust cover) carefully over the lid hinges (23) and adjust the screws (24) until the lid stays
open where you want it to without being too stiff to open or close.
Changing replay speed
Put the belt (6) over the larger diameter part of the motor pulley (7). To revert to 33 r.p.m. repeat the
proceedings using the smaller step on the pulley.
For detailed product information please refer to the Pro-Ject web site www.project-audio.com.
Maintenance and cleaning
Your record player requires little or no regular maintenance. Remove dust with a slightly moistened
antistatic cloth. Never use a dry cloth because this will create static electricity which attract more dust!
Antistatic cleaning fluids are available at specialist stores but must be applied sparingly to avoid
damage to rubber parts. It is recommended to fit the needle cover before cleaning or maintenance is
carried out to avoid damage.
If the player is not used over a long period of time the drive belt can be removed to prevent unequal
stretching.
!
Always disconnect the record player from the mains power supply as a precaution before
maintenance!
Mounting and connecting the cartridge
** All cartridges with half inch mounting holes can be fitted. Leaving the needle's protection cover on,
fit the cartridge to the headshell (12) using the screws supplied with the cartridge by passing one
screw through each slot in the headshell (12). Do not tighten the nuts yet.
Connect the tonearm wires to the cartridge pins as follows:
white
red
green
blue
left channel positive (L+)
right channel pos. (R+)
right channel return (R -)
left channel return (L -)
The full sound quality of the record player can only be achieved if the cartridge is correctly adjusted.
Particular tools like the Pro-Ject alignment tool “Align IT” are required to accomplish this job properly.
If you are not well acquainted with the adjustment of cartridges you are advised to call upon the willing
help of your Pro-Ject dealer to accomplish this task for you.
Please note: Adjusting a cartridge and tonearm calls for the greatest care in order to avoid
damaging the cartridge or tonearm bearings. Leave this work to your dealer if you are in any
way unsure of the necessary steps and precautions to be taken.
Useful tips
The record player should be positioned on a low-resonance surface such as wood or multiple layer ply
board to avoid structural vibrations disturbing replay.
8
© Pro-Ject Audio Systems · Pro-Ject Jukebox S2 · Revision 2018.04.04
Technical specifications Pro-Ject Jukebox S2 / Pro-Ject 8.6 E
Turntable
Nominal speeds
Speed variance
Wow and flutter
Signal to noise
Effective tonearm mass
Effective tonearm length
Overhang
333/45 r.p.m.
333: ±0,80% 45: ±0,70%
333: ±0,29% 45: ±0,27%
-65dB
88,0g
8,6" (218,5mm)
22,0mm
Amplifier
Power output
SNR
Volume control
THD +N
Crosstalk
Phono amplifier
Phono gain:
Line level inputs
Amplifier gain
Bluetooth
Treble equalizer
2 x 50W at 4 ohms
-75dB
32 step
0,5% at 1kHz, RL = 8 ohms, P = 1W
-80 dB
Moving magnet (MM)
43dB
2 pairs RCA
32 dB
2.1 + EDR
+- 12dB
Bass equalizer
+- 12dB
General
Replacement battery remote control
2 x AAA
Power consumption
Outboard power supply
Dimensions (W x H x D)
Weight
Dimensions packaging (W x H x D)
4,5W
24V/4A DC
415 x 118 x 334mm
5,0kg
488 x 235 x 393mm
Weight incl. packaging
7kg
© Pro-Ject Audio Systems · Pro-Ject Jukebox S2 · Revision 2018.04.04
9
Potential incorrect use and fault conditions
Pro-Ject turntables are manufactured to the highest standards and undergo strict quality controls
before leaving the factory. Faults that may possibly occur are not necessarily due to material or
production faults but can sometimes be caused by incorrect use or unfortunate circumstances. Therefore
the following list of common fault symptoms is included.
The platter doesn't turn although the unit is switched on:
The unit is not connected to the mains power supply.
No mains at the socket.
Drive belt is not fitted or has slipped off.
No signal through one or other channel or both channels:
No signal contact from the cartridge to the internal tonearm wiring or from that to the arm lead or
from that to the phono box or between that and the amplifier. This could be due to a faulty plug,
broken wire or solder joint or simply loose plug/socket connection.
Phono input not selected at amplifier.
Amplifier is not switched on.
Amplifier or speakers are defective or muted.
No connection to the loudspeakers.
Strong hum on phono input:
No earth connection from cartridge or arm or arm cable to amplifier, or earth loop.
Distorted or inconsistent sound from one or both channels:
Record player is connected to wrong input of amplifier, or MM/MC switch incorrectly set.
Needle or cantilever damaged.
Wrong r.p.m., drive belt overstretched or dirty, platter bearing without oil, dirty or damaged
Service
Should you encounter a problem which you are not able to alleviate or identify despite the above
information, please contact your dealer for further advice. Only when the problem cannot be resolved
there should the unit be sent to the responsible distributor in your country.
Guarantee repairs will only be affected if the unit is returned correctly packaged. For this reason we
recommend keeping the original packaging.
Never return a record player without making sure that is it safely disassembled and correctly packaged
in the original packaging according to the diagrams on the last page of this user guide. Please remove
these parts and pack them separately: lid, counterweight (4), anti-skating weight (10) and belt (22).
Fit the cartridge protection cap and the transport lock for the tonearm tube (66), prior to carefully
packaging the record player.
Warranty
The manufacturer accepts no responsibility for damage caused by not adhering to these
instructions for use and/or by transportation without the original packaging. Modification or
change to any part of the product by unauthorized persons, release the manufacturer from any
liability over and above the lawful rights of the customer.
Pro-Ject Audio Systems is a Registered Trademark of
H. Lichtenegger.
This guide was produced by: Pro-Ject Audio Systems
©
Copyright 2018. All rights reserved.
10
The information was correct at the time of going to
press. The manufacturer reserves the right to make
changes to the technical specification without prior
notice as deemed necessary to uphold the ongoing
process of technical development.
© Pro-Ject Audio Systems · Pro-Ject Jukebox S2 · Revision 2018.04.04
© Pro-Ject Audio Systems · Pro-Ject Jukebox S2 · Revision 2018.04.04
11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising