Pro-Ject | Elemental Phono USB | manual | Pro-Ject Elemental Phono USB Manual

Pro-Ject Elemental Phono USB Manual
INSTRUCTIONS FOR USE
Pro-Ject Elemental/Phono USB
Controls, features and connections
1
Power switch
2/22
Stepped drive pulley and drive belt *
3
Platter with felt mat *
4
Tonearm counterweight
5
Tonearm lift lever
6/66
Tonearm rest and removable transport lock
7
Tonearm tube
8
Headshell with finger lift and fitted Ortofon OM 5E cartridge
9
Phono output sockets, earth connection and USB-out
10
Power supply socket
Power supply (not shown)*
Signal output and USB-cable (not shown)*
Hexagonal allen wrench (not shown) *
2
© Pro-Ject Audio Systems· Pro-Ject Elemental Phono USB/ Ortofon OM 5E · Revision 2016.07.19
Pro-Ject Elemental/Phono USB
Dear music lover,
thank you for purchasing a record player from Pro-Ject Audio Systems.
In order to achieve maximum performance and reliability with this record player you should study these instructions
for use carefully.
!
Warning of a hazard for the user, the unit or possible misuse.
Important notice.
** Your turntable has been delivered with a factory fitted and adjusted cartridge, please ignore the
cartridge set up instructions unless changing the cartridge at a later date.
During assembly and adjustment of the deck small parts could be lost if not carefully placed in a suitable
receptacle. Before starting assembly make yourself acquainted with the parts listed above and correspondingly
numbered in the technical drawings above. Separately packed items are marked with an asterisk *.
Safety instructions
!
AC outlet voltages vary from country to country. Before connecting to the mains, make sure that the
voltage in your area meets the voltage requirements printed on the power supply.
The power supply is used to disconnect the unit from the mains. Make sure that the power supply is easily
accessible at all times. Never handle the device, the power supply while your hands are wet or damp.
Avoid letting liquids enter the device or the power supply. Never place any item containing liquid,
such as a flower vase on or near the device. Never spill any liquid on the device or the power supply.
Never place any naked flame sources, such as lighted candles on or near the device. The product shall not
be used in damp or wet locations, next to a bathtub, sink, swimming pool or any other similar conditions.
Keep plastic bags away from children to prevent any risk of suffocation.
Set-up
The deck is supplied partially disassembled and carefully packaged for safe transport. Carefully remove all
parts from the transport packaging.
Make sure the surface you wish to use the turntable on is level (use a spirit level) before placing the turntable on it.
Fit the drive belt (22) around the platter (3) and the smaller diameter part of the motor pulley (2). Avoid
getting sweat or grease on the belt as these will deteriorate the performance and reduce the belt's lifespan. Use
absorbent kitchen paper to remove any oil or grease from the outer edge of the platter and the belt.
Fit the felt mat over the spindle of the platter (3). Remove the transport lock (66) from the tonearm tube.
Store the transport lock in the original packaging so they are available for any future transportation.
Cartridge downforce adjustment
The counterweight (4) supplied is suitable for cartridges weighing between 3,5 - 5,5g. The counterweight is
pre-set perfectly from the factory.
© Pro-ject Audio Systems · Pro-Ject Elemental Phono USB / Ortofon OM 5E · Revision 2016.07.19
3
Connection to the amplifier
The record player has gold plated female RCA phono sockets (12) so you can substitute the interconnect cables
supplied with those of your choice for connection to the amplifier if you wish. Your dealer can advise you on
alternative cables. Use a line input (such as AUX, CD, Tuner, Tape or Video) on your amplifier.
Due to the built in phono pre-amplifier, a phono input (sometimes labelled gram, disc or RIAA) is not
suitable.
Take care to connect the left and right channels correctly. The right channel is usually marked red, the left
channel black or white. Check the manual supplied with your amplifier for relevant information. The earthing
wire of the tonearm lead should be connected to the earth terminal on your amplifier (if provided).
!
Connecting to a Computer
Connect the USB-output of the unit to a free USB-socket on your computer and turn it on/make sure it is
powered on.
The “new hardware found assistant“ will automatically detect the unit and announces it as a Microphone USB
audio codec. There is no need to install a driver manually.
After installation, one setting has to be done. For example - Windows 7® operating system:
 Control Panel  Sound  Recording  Microphone USB Audio CODEC  Properties 
Advanced: set to 2 channel, 16 bit, 48000 Hz (DVD Quality)
Please note: Connection should be made to an USB-socket of your computer directly. Connecting to
USB-hubs or switches can cause problems.
Recording Programme
In case you do not have a recording programme installed on your computer, you may download one free from
the Internet. Recording programmes may be found by searching Google.
In the menu of the recording programme, source or input may have to be set to Microphone USB audio codec.
Please be aware that downloads from the Internet are made entirely at your own risk. Under no
circumstances can we carry responsibility or provide support for third-party software products sourced
from the internet or for any damage or problems arising from the use thereof. All downloads should
be checked with an up-to-date anti-virus programme. License fees may be applicable.
Mains power connection
The turntable is supplied with a power supply suitable for your country's mains supply. Check the label before
connecting to ensure compliance with the mains rating in your house.
Connect the low voltage plug from the power supply to the socket (10) on the rear of the record player
before connecting the power supply to the mains.
Switching on and off
Pressing the power switch (1) alternately starts or stops the motor.
Changing replay speed
Put the belt (22) over the larger diameter part of the motor pulley (2). To revert to 33 r.p.m. repeat the
proceedings using the smaller step on the pulley.
For detailed product information please refer to the Pro-Ject web site www.project-audio.com.
4
© Pro-Ject Audio Systems· Pro-Ject Elemental Phono USB/ Ortofon OM 5E · Revision 2016.07.19
Maintenance and cleaning
Your record player requires little or no regular maintenance. Remove dust with a slightly moistened antistatic
cloth. Never use a dry cloth because this will create static electricity which attract more dust! Antistatic
cleaning fluids are available at specialist stores but must be applied sparingly to avoid damage to rubber
parts. It is recommended to fit the needle cover before cleaning or maintenance is carried out to avoid damage.
If the player is not used over a long period of time the drive belt can be removed to prevent unequal stretching.
!
Always disconnect the record player from the mains power supply as a precaution before maintenance!
Fitting and connecting the cartridge
**Other cartridges with half inch mounting holes can be fitted. Please consider adequate cartridge
weight, because this tonearm is optimised for lightweight cartrigdes like OM series. Leaving the needle's
protection cover on, fit the cartridge to the headshell (8) using the screws supplied with the cartridge by
passing one screw through each slot in the headshell (8). Do not tighten the nuts yet.
Connect the tonearm wires to the cartridge pins as follows:
white
red
green
blue
left channel positive (L+)
right channel pos. (R+)
right channel return (R -)
left channel return (L -)
The full sound quality of the record player can only be achieved if the cartridge is correctly adjusted. Particular
tools like the Pro-Ject alignment tool “Align it” are required to accomplish this job properly.
If you are not well acquainted with the adjustment of cartridges you are advised to call upon the willing help of
your Pro-Ject dealer to accomplish this task for you.
Please note: Adjusting a cartridge and tonearm calls for the greatest care in order to avoid damaging
the cartridge or tonearm bearings. Leave this work to your dealer if you are in any way unsure of the
necessary steps and precautions to be taken.
Useful tips
The record player should be positioned on a low-resonance surface such as wood or multiple layer ply board
to avoid structural vibrations disturbing replay.
© Pro-ject Audio Systems · Pro-Ject Elemental Phono USB / Ortofon OM 5E · Revision 2016.07.19
5
Technical specifications Pro-Ject Elemental / Pro-Ject 8.6
Nominal speeds
Speed variance
Wow and flutter
Signal to noise
Effective tonearm mass
Effective tonearm length
Overhang
Power consumption
Outboard power supply
Dimensions (W x H x D)
Weight
Dimensions packaging (W x H x D)
Weight incl. packaging
33/45 r.p.m.
33: 0,80% 45: 0,70%
33: 0,29% 45: 0,27%
65dB
8g
8,6" (218,5mm)
22mm
4,0W
15V/500mA DC, suitable for your country's mains supply
430 x 90 x 300mm (WxHxD)
2,7kg
530 x 370 x 155mm
4,5kg
Technical specifications MM-Cartridge Ortofon OM 5E
Frequency range
Channel separation
Output voltage
Recommended load impedance
Compliance/stylus type
Recommended tracking force
Weight
20-25.000Hz
22dB/1kHz
4mV
47kohms / amplifier connection – MM-input
20µm/mN – elliptical
17,5mN
5g
Technical specifications moving magnet phono pre-amplifier
Gain
Output voltage typically
Input impedance
Noise floor
RIAA-equalisation curve accuracy
USB output:
Operating systems:
6
32dB
160mV/1kHz at 4mV/1kHz input
47kohms/100pF
-88dB
20Hz-20kHz / max. 0,5dB
digital serial data protocol USB 1.1
Windows XP®, Windows VISTA®, Windows 7®, Windows 8®, Mac OS
© Pro-Ject Audio Systems· Pro-Ject Elemental Phono USB/ Ortofon OM 5E · Revision 2016.07.19
Potential incorrect use and fault conditions
Pro-Ject turntables are manufactured to the highest standards and undergo strict quality controls before
leaving the factory. Faults that may possibly occur are not necessarily due to material or production faults but
can sometimes be caused by incorrect use or unfortunate circumstances. Therefore the following list of common
fault symptoms is included.
The platter doesn't turn although the unit is switched on:
The unit is not connected to the mains power supply.
No mains at the socket.
Drive belt is not fitted or has slipped off.
No signal through one or other channel or both channels:
No signal contact from the cartridge to the internal tonearm wiring or from that to the arm lead or
from that to the phono box or between that and the amplifier. This could be due to a faulty plug,
broken wire or solder joint or simply loose plug/socket connection.
Phono input not selected at amplifier.
Amplifier not switched on.
Amplifier or speakers defective or muted.
No connection to the loudspeakers.
Strong hum on phono input:
No earth connection from cartridge or arm or arm cable to amplifier, or earth loop.
Distorted or inconsistent sound from one or both channels:
Record player is connected to wrong input of amplifier, or MM/MC switch incorrectly set.
Needle or cantilever damaged.
Wrong r.p.m., drive belt overstretched or dirty, platter bearing without oil, dirty or damaged.
Service
Should you encounter a problem which you are not able to alleviate or identify despite the above information,
please contact your dealer for further advice. Only when the problem cannot be resolved there should the
unit be sent to the responsible distributor in your country.
Guarantee repairs will only be effected if the unit is returned correctly packaged. For this reason we recommend
keeping the original packaging.
Never return a record player without making sure that is it safely disassembled and correctly packaged in the
original packaging according to the diagrams on the last page of this user guide.
Fit the cartridge protection cap and the transport lock for the tonearm tube (66), prior to carefully packaging
the record player.
Warranty
The manufacturer accepts no responsibility for damage caused by not adhering to these instructions
for use and/or by transportation without the original packaging. Modification or change to any part
of the product by unauthorized persons release the manufacturer from any liability over and above
the lawful rights of the customer.
PRO-JECT is a Registered Trademark of H. Lichtenegger. The information was correct at the time of going to
press. The manufacturer reserves the right to make
This guide was produced by: Pro-Ject Audio Systems
changes to the technical specification without prior
Copyright © 2014. All rights reserved.
notice as deemed necessary to uphold the ongoing
process of technical development.
© Pro-ject Audio Systems · Pro-Ject Elemental Phono USB / Ortofon OM 5E · Revision 2016.07.19
7
8
© Pro-Ject Audio Systems· Pro-Ject Elemental Phono USB/ Ortofon OM 5E · Revision 2016.07.19
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising