TOA | ZM-9003 | Specification Sheet | TOA AN-9001 Specification

TOA AN-9001 Specification
M-9000
Digital Matrix Mixer
APPEARANCE AND
DIMENSIONAL DIAGRAM
Rear View
DESCRIPTION
482
466
420
6.1
Top View
76.2
88.4
107.6
The TOA M-9000 Digital Matrix Mixer features a compact design that
fits in a two rack space package. The versatile new mixer is ideal for
multi-zone paging, music distribution and room-combining applications.
The M-9000 includes eight module ports allowing designers to easily
configure custom systems with up to eight mic/line inputs and eight
outputs. The M-9000 chassis has two channels of built-in digital signal
processing (DSP) with ten band parametric EQ, compressor, eight
level ducking and more. Input and output modules provide additional
DSP.
Two discrete operation modes, "Mixer" and "Matrix", allow the M-9000
to be used in both simple mixing and complex multi-zone paging
applications. Versatile features include telephone zone paging,
automatic microphone mixing and ambient noise control.
Front View
14
353
335
SYSTEM FEATURES
■ Modular Digital Matrix Mixer for a multitude of applications
including audio-visual, zone paging, room combining and many more.
■ Dual Modes (Mixer and Matrix) — two separate feature sets to suit
both simple mixing and complex multi-zone distribution applications.
■ Easy to Configure and Operate
■ Exceptional Audio Quality
• 24-bit, 48 kHz sampling
• Low Distortion - 0.008%
■ Modular System— up to 8 mic/line inputs and 8 outputs.
■ Dual Channel Digital Signal Processor (DSP):
• 10-band parametric EQ
• High and low pass filters
• Compressor
• Loudness contour
• Bass and treble
• Delay (Mixer mode)
• TOA Speaker EQ presets
• Additional DSP included on D-001T, D-001R and T-001T modules
■ Telephone Zone Paging— access up to eight zones with optional
ZP-001T module
■ Ambient Noise Control— automatically increase or reduce output
levels in response to changes in ambient noise.
■ Multi-function Display allows programming and operation without
a PC.
■ Rack-mount Kit Included (2RU)
Side View
Flexible Remote Control
Two Remote Volume Control Terminals
• Assignable to any input or output channel
• Control with 10k ohm linear potentiometer, 0-10 VDC or optional
ZM-9001/ZM-9002 remote panels
• Assign remote volume control to background music (Priority 8)
inputs without affecting paging input volume
Four Control Inputs (expandable to twelve with C-001T module)–
programmable to activate Memory, Volume Up/Down, Mute, Power
On/Off, Emergency Mute
• ZM-9003 can also be connected.
Four Control Outputs (expandable to twelve with C-001T module) –
programmable to activate external relays synchronized with Memory,
Channel On/Off and Power On/Off
RS-232 Port
• Control protocol available for external devices (see protocol for
controllable parameters)
• AMX and Crestron control modules available
Additional Features
Software Utility for saving unit parameters to PC, updating unit
firmware, virtual control activation and status indication
MS Excel Programming Templates – use Microsoft(R) Excel for offsite programming
Keylock Security sets password-protected access to Input,
Output, Utility & Power functions
Input and Output Metering (D-001 module(s) required for input
metering)
Alphanumeric Channel and Memory Naming
Power On Memory sets the Event/Scene selected when unit
powers up
Detachable AC Cable
M-9000 Digital Matrix Mixer
SPECIFICATIONS
Power Requirement
Power Consumption
Audio Input
Audio Output
Module Slot
Digital Audio Signal Reference Level
Frequency Response
Total Harmonic Distortion
S/N Ratio
Crosstalk
Tone Control
Parametric Equalizer
Speaker Equalizer
High-pass Filter
Low-pass Filter
Compressor
Delay
Scene/Event Memory
Operation Mode
Auxiliary Function
Control Input/Output
Operating Temperature
Operating Humidity
Finish
Dimensions
Weight
Accessory
AC mains, 50/60 Hz
40W
Max. 8 channels, modular construction (modules optional)
Preamplifier output 1, 2: 0 dB*, 600 ohms, balanced, removable terminal block (3 pins)
Analog input (slot 1 – 8): –10dB*, 10 k ohms, unbalanced
Digital input (slot 1– 4): 24 bit/48kHz
MIX output (slot 1 – 8): -14dB*, 330 ohms (CH 1 prefader output), unbalanced
Digital output (slot 5 – 7): 24 bit/48kHz
Power supply (slot 1 – 8): 24V, -24V, :6V DC
–20dBFS
20 – 20,000 Hz, +1, –3 dB
0.008% (at 22 kHz LPF, 1 kHz, +10 dBV output)
At Input short, 20 – 20,000 Hz, ALL FLAT or OFF setting
Output volume min.: 90 dB
Output volume max.: 61 dB (input 1 vol.: 0 dB, other inputs: OFF)
Over 64 dB (at 20 kHz)
Bass: +/–12 dB (at 100 Hz), Treble: +/–12 dB (at 10 kHz)
10 bands, Freq: 20 – 20,000Hz, 31 steps, Various range: +/–12 dB, Q: 0.3 – 5
15 (compatible with TOA speakers only)
–12 dB/oct, Variable frequency range: 20 – 400 Hz, 14 steps
–12 dB/oct, Variable frequency range: 4,000 – 20,000 Hz, 8 steps
Depth: 1 – 5
0 – 40 ms (1 ms steps), maximum 40 ms (CH1 + CH2) (Mixer mode only)
32
Matrix mode/Mixer mode (selector switch)
Key lock function
RS-232C*2, D-sub connector (9P, female)
Control input: 4 inputs, no-voltage make contact input, open voltage: 3.3 V DC, short-circuit current: under 1 mA, removable terminal block (14 pins)
Control output: 4 outputs, open collector output, withstand voltage: 27 V DC, control current: 50 mA, removable terminal block (14 pins)
Remote volume: 2 channels, connect a 10 k ohms/linear taper variable resistor or input the DC voltage of 0 to +10V, removable terminal block (14 pins)
–10°C to 40°C
35% to 80% RH (no condensation)
Panel: Aluminum, hair-line, black, Case: Surface-treated steel plate, black paint
420 (W) × 107.6 (H) × 353 (D) mm
6 kg (without modules)
Power cord (2m) × 1, Rack Mounting bracket × 2, Bracket mounting screw × 4, Blank panel × 7, Blank panel mounting screw × 14,
Removable terminal plug (3 pins) × 2, Removable terminal plug (14 pins) × 1, CD-ROM × 1, Start guide × 1
* 0dB = 1V
*2 Allowing it to be controlled by a control system such as AMX and Crestron through RS-232C port.
Notes: AMX is a tradmark of AMX Corporation. Crestron is a tradmark of Crestron Electronics. Inc.
C-001T Control Input/Output Module
SPECIFICATIONS
Power Requirement
Current Consumption
Control Input
Control Output
Operating Temperature
Finish
Dimensions
Weight
Accessory
The C-001T is Control I/O expansion module designed for use
with the M-9000 and can provide up to 8 channels each of input
and output expansion. Since the main unit has 4 preinstalled
inputs and outputs each, the control input and output can be
expanded to up to 12 channels each when the C-001T is used.
91.5
78
35
Unit: mm
6 V DC
15 mA
8 channels, open voltage: 3.3 V DC, short-circuit
current: under 1 mA, removable terminal block (9 pins)
8 channels, open collector output, withstand voltage: 27 V DC,
control current: max. 50 mA, removable terminal block (9 pins)
-10°C to +40°C
Panal: Aluminum, hair-line
35 (W) × 78 (H) × 91.5 (D) mm
62 g
Removable terminal plug (9 pins) × 2, Module mounting screw × 2
D-001T Dual Mic/Line Input Module with DSP
SPECIFICATIONS
Power Requirement
Current Consumption
Input
The D-001T is a plug-in module designed for use with the
M-9000 and can provide two independent balanced inputs. The
D-001T can handle signals ranging from microphone level to line
level by controlling their input sensitivity in 9 increments from
-60dB to -10dB.
Phantom power (+24V) can be supplied for condenser
microphone use. The D-001T can process effect for TONE/EQ/
COMPRESSOR to two inputs independently.
91.5
High-pass Filter
Low-pass Filter
Compressor
Phantom Power
Operating Temperature
Finish
Dimensions
Weight
Accessory
*0 dB = 1 V
78
35
Input Sensitivity
Frequency Response
THD + N
Input Equivalent Noise
S/N Ratio
Cross Talk
CMRR
A/D Converter
Sampling Frequency
Tone Control
Parametric Equalizer
+24 V DC, -24 V DC, +6 V DC
20 mA (at +24 V DC), 20 mA (at -24 V DC), 60 mA (at +6 V DC)
2 channels, 3 k ohms (when the phantom power is ON)/
10 k ohms (when the phantom power is OFF),
electronically-balanced, removable terminal block (3 pins)
-60, -54, -48, -42, -36, -30, -24, -18, -10 dB* (selectable)
20 – 20,000 Hz, +1, -3 dB
0.008% (at 1 kHz, 20 – 20,000 Hz BPF, Input sensitivity: -10 dB)
Under -112 dB (at 20 – 20,000 Hz BPF, Input short, Input sensitivity: -60 dB)
Over 73 dB (at 20 – 20,000 Hz BPF, Input short, Input sensitivity: -10 dB)
Over 75 dB (at 20 kHz, Input sensitivity: -10 dB)
Over 62 dB (at 1 kHz, Input sensitivity: -60 dB)
24 bit ∆∑ADC
48 kHz
Bass: ±12 dB (at 100 Hz), Treble: ±12 dB (at 10 kHz)
10 bands, Frequency: 20 – 20,000 Hz, 31 steps,
Variable range: ±12 dB, Q: 0.3-5
-12 dB/oct, Variable frequency range: 20 – 400 Hz, 14 steps
-12 dB/oct, Variable frequency range: 4,000 – 20,000 Hz, 8 steps
Depth: 1 – 5
+24 V DC
-10°C to +40°C
Panel: Aluminum, hair-line
35 (W) × 78 (H) × 91.5 (D) mm
82 g
Removable terminal plug (3 pins) × 2, Module mounting screw × 2
Unit: mm
D-001R Line Input Module with DSP
SPECIFICATIONS
Power Requirement
Current Consumption
Intput
Intput Sensitivity
Frequency Response
THD + N
S/N Ratio
Cross Talk
A/D Converter
Sampling Frequency
Tone Control
Parametric Equalizer
The D-001R is a line input plug-in module designed for use with
the M-9000. It has 2-channel unbalanced input of RCA jacks.
Input signals to both channels are mixed together. The D-001R
can process effect for TONE/EQ/COMPRESSOR to two inputs
independently.
91.5
78
35
Unit: mm
High-pass Filter
Low-pass Filter
Compressor
Operating Temperature
Finish
Dimensions
Weight
Accessory
*0 dB = 1 V
+24 V DC, -24 V DC, +6 V DC
20 mA (at +24 V DC), 20 mA (at -24 V DC), 60 mA (at +6 V DC)
2 channels, 2 RCA/ch mixed, 10 k ohms, unbalanced, RCA pin jack
-60, -54, -48, -42, -36, -30, -24, -18, -10 dB* (selectable)
20 – 20,000 Hz, +1, -3 dB
0.008% (at 1 kHz, 20 – 20,000 Hz BPF, Input sensitivity: -10 dB)
Over 70 dB (at 20 – 20,000 Hz BPF, Input short, Input sensitivity: -10 dB)
Over 75 dB (at 20 kHz, Input sensitivity: -10 dB)
24 bit ∆∑ADC
48 kHz
Bass: ±12 dB (at 100 Hz), Treble: ±12 dB (at 10 kHz)
10 bands, Frequency: 20 – 20,000 Hz, 31 steps,
Variable range: ±12 dB, Q: 0.3 – 5
-12 dB/oct, Variable frequency range: 20 – 400 Hz, 14 steps
-12 dB/oct, Variable frequency range: 4,000 – 20,000 Hz, 8 steps
Depth: 1 – 5
-10°C to +40°C
Panel: Aluminum, hair-line
35 (W) × 78 (H) × 91.5 (D) mm
82 g
Module mounting screw × 2
T-001T Dual Line Output Module with DSP
SPECIFICATIONS
Power Requirement
Current Consumption
Output
Frequency Response
THD + N
S/N Ratio
Residual Noise
Cross Talk
D/A Converter
Sampling Frequency
Tone Control
Parametric Equalizer
The T-001T is a plug-in module designed for use with the M-9000
and provide two independent balanced outputs. It can drive load
of 600 ohms up to +16dB. It can process effect for TONE/EQ/
COMPRESSOR to two inputs independently.
91.5
78
35
Speaker Equalizer
High-pass Filter
Low-pass Filter
Compressor
Delay
Operating Temperature
Finish
Dimensions
Weight
Accessory
*0 dB = 1 V
+24 V DC, -24 V DC, +6 V DC
35 mA (at +24 V DC), 35 mA (at -24 V DC), 60 mA (at +6 V DC)
2 channels, max. +20 dB* (at 10 k ohms load), 600 ohms,
electronically-balanced, removable terminal block (3 pins)
20 – 20,000 Hz, +1, -3 dB
0.005% (at 1 kHz, 20 – 20,000 Hz BPF, 5 V output, 10 k ohms load)
Over 73 dB (at 20 – 20,000 Hz BPF )
Under -91 dB (at 20 – 20,000 Hz BPF, VOL: -70 dB)
Over 87 dB (at 20 kHz)
24 bit ∆∑ADC
48 kHz
Bass: ±12 dB (at 100 Hz), Treble: ±12 dB (at 10 kHz)
10 bands, Frequency: 20-20,000 Hz, 31 steps,
Variable range: ±12 dB, Q: 0.3-5
15 (compatible with TOA speakers only)
-12 dB/oct, Variable frequency range: 20 – 400 Hz, 14 steps
-12 dB/oct, Variable frequency range: 4,000 – 20,000 Hz, 8 steps
Depth: 1-5
0-40 ms (1 ms step), maximum 40 ms (CH 1 + CH2), mixer mode only
-10°C to +40°C
Panel: Aluminum, hair-line
35 (W) × 78 (H) × 91.5 (D) mm
82 g
Removable terminal plug (3 pins) × 2, Module mounting screw × 2
Unit: mm
SS-9001 Speaker Selector
SPECIFICATIONS
Power Requirement
Current Consumption
Control Signal
photo: 70 V line model
1
177
197
18
30
70
112
18
10
157
The SS-9001 is a speaker selector used in conjunction with the
M-9000. It outputs 2 input signals to 4 different zones.
Unit: mm
Control Power
Speaker Terminal
Control Terminal
Operating Temperature
Finish
Dimensions
Weight
Accessory
Option
Supplied from the optional AD-246 AC adapter or an
external 24 V DC/200 mA power supply.
120 mA
No-voltage make contact input (polarized),
open voltage: 24 V DC, short-circuit current: 3 mA
240 W or less (70 V/100 V line)
Removable terminal block (2 pins)
Removable terminal block (10 pins)
-10°C to +40°C
Case: Surface-treated steel plate
112 (W) × 197 (H) × 30 (D) mm
530 g
Removable terminal plug (2 pins) × 6,
Removable terminal plug (10 pins) × 1, Cord clamp × 1, Mounting screw × 4
AC adapter: AD-246
AN-001T Ambient Noise Controller Module
SPECIFICATIONS
Power Requirement
Current Consumption
Input
Input Sensitivity
Phantom Power
A/D Converter
Sampling Frequency
Ambient Noise Control
Function
The AN-001T is a plug-in module of 2-channel ambient noise
detector designed for use with the M-9000.
It automatically adjusts the output volume in response to the
change of ambient noise level. The AN-001T can handle input
signals from microphone level (-60dB) to line level (-10dB) by
controlling the gain in 9 steps.
Phantom power (+24V) can be supplied for condenser microphone
use.
91.5
78
35
Operating Temperature
Finish
Dimensions
Weight
Accessory
Option
*0 dB = 1 V
+24 V DC, -24 V DC, +6 V DC
20 mA (at +24 V DC), 20 mA (at -24 V DC), 60 mA (at +6 V DC)
Sensor input (Ambient noise sensor microphone input):
2 channels, 3 k ohms (when the phantom power is ON)/10 k ohms
(when the phantom power is OFF), electronically-balanced,
removable terminal block (3 pins)
-60, -54, -48, -42, -36, -30, -24, -18, -10 dB* (selectable)
+24 V DC
24 bit ∆∑ADC
48 kHz
Sensor input reference level adjustment function
Maximum output signal level control: -15 to 0 dB
Minimum output signal level control: -18 to -3 dB
Sample time setting: 10 s, 15 s, 20 s, 30 s, 1 min, 2 min, 3 min, 5 min
Gain ratio setting (Ambient noise: Output signal level):
6:3, 5:3, 4:3, 3:3, 3:4, 3:5, 3:6, 6:-3, 5:-3, 4:-3, 3:-3, 3:-4, 3:-5, 3:-6,
-10°C to +40°C
Panel: Aluminum, hair-line
35 (W) × 78 (H) × 91.5 (D) mm
82 g
Removable terminal plug (3 pins) × 2, Module mounting screw × 2
Ambient Noise Sensing Microphone: AN-9001
Unit: mm
AN-9001 Ambient Noise Sensing Microphone
SPECIFICATIONS
Type
Phantom Power
Current Consumption
Directivity
Impedance
Rated Sensitivity
Frequency Response
Output Terminal
Operating Temperature
Finish
70
ø130
The AN-9001 is an electret condenser microphone designed for
ambient noise detection. It is used in conjunction with the
AN-001T Ambient Noise Controller Module.
It can be mounted in an American standard 1-gang electrical box
in the ceiling or wall.
31
37
1-gang electrical box
(not supplied)
70
83.5
104
83.5
90 – 98
38
42
70
Front View
without panel
46 – 50
Figure when
mounted
Dimensions of mounting
opening
If the opening is too small or
too large, the AN-9001
cannot be mounted in the
wall. Be sure to make an
opening with dimensions
given above when mounting.
Unit: mm
Electret condenser microphone
14-26 V DC
7 mA (at 24 V DC)
Omnidirectional (hemispherical)
200 ohms
-5 dB (1 kHz, 0 dB = 1 V/Pa)
100-10,000 Hz
Removable terminal block (3 pins)
-10°C to +40°C
Panel: ABS resin, white
Frame, Case: Surface-treated steel plate
Dimensions
ø130 × 37 (D) mm
Weight
170 g
Accessory
Removable terminal plug (3 pins) × 1,
Box mounting screw (No.6-32UNC x 30) × 2,
Box mounting screw (M4 x 30) × 2
Option
Ambient Noise Controller Module: AN-001T
Note: Since no electrical box is supplied with the unit, prepare it separately.
ZP-001T Telephone Zone Paging Module
SPECIFICATIONS
Power Requirement
Current Consumption
Number of Line
Type of Selectable
Signaling System
TEL Line
Paging Input
Control Input
Control Output
The ZP-001T is a zone paging module designed for use with the
M-9000 and functions as interface to connect the M-9000 to an
analog PABX, allowing zone paging to be initiated from the PABX.
There are two operation modes: ring signal and paging port modes.
Broadcast can be initiated regardless of operation mode.
91.5
78
35
Operating Temperature
Finish
Dimensions
Weight
Accessory
+24 V DC, +6 V DC
38 mA (at +24 V DC), 18 mA (at +6 V DC)
1 line
Signal DTMF signal
Loop-Start (or Ground-Start, selectable)
0 dB, 600 ohms, balanced, transformer-isolated, loop voltage: 24 V DC or more,
which should be supplied from the PABX, RJ11 connector
0 dB, 600 ohms, balanced, transformer-isolated audio input,
removable terminal block (4 pins)
1 channel, no-voltage make contact, open voltage: 5 V DC,
short-circuit current: 0.5 mA, removable terminal block (4 pins)
4 channels, open collector output (isolated), withstand voltage: 35 V DC,
control current: max. 50 mA, removable terminal block (4 pins)
-10°C to +40°C
Panel: Aluminum, hair-line
35 (W) × 78 (H) × 91.5 (D) mm
153 g
Removable terminal plug (4 pins) × 3, Module mounting screw × 2
Unit: mm
ZM-9001 Remote Panel
SPECIFICATIONS
Applicable Cable
Line Resistance
Terminal
Operating Temperature
Finish
Dimensions
Weight
Accessory
Single conductor shielded cable
Under 50 ohms (per line)
M3 screw terminal, distance between barriers: 7.62 mm
-10°C to +40°C
Surface-treated steel plate, white, paint
72 (W) × 127 (H) × 45 (D) mm
170 g
Box mounting screw (No.6–32UNC × 30) × 2,
Box mounting screw (M4 × 30) × 2, Panel mounting screw × 2
Note: Since no electrical box is supplied with the unit, prepare it separately.
72
33
45
37
66
83.5
97
104
32.6
70
66.4
97
127
Front View
without panel
6
38
42
Unit: mm
Figure when mounted
1-gang electrical box
(not supplied)
83.5
90 – 98
The ZM-9001 is a remote control switch panel used with the M-9000.
It provides an additional 6 control inputs of amplifier expansion, and
can be mounted in an American standard 1-gang electrical box in
the wall. Up to 2 ZM-9001/9002 units can be connected to the
M-9000.
46 – 50
Dimensions of mounting opening
If the opening is too small or too large, the
ZM-9001 cannot be mounted in the wall.
Be sure to make an opening with
dimensions given above when mounting.
ZM-9002 Remote Panel
SPECIFICATIONS
Applicable Cable
Line Resistance
Terminal
Operating Temperature
Finish
Dimensions
Weight
Accessory
Single conductor shielded cable
Under 50 ohms (per line)
M3 screw terminal, distance between barriers: 7.62 mm
-10°C to +40°C
Surface-treated steel plate, white, paint
72 (W) × 127 (H) × 56 (D) mm
170 g
Box mounting screw (No.6–32UNC × 30) × 2,
Box mounting screw (M4 × 30) × 2, Panel mounting screw × 2
Note: Since no electrical box is supplied with the unit, prepare it separately.
70
66
83.5
97
104
32.6
66.4
97
127
The ZM-9002 is a remote control switch/volume panel used with
the M-9000.
It adds 4 amplifier control inputs and 1 remote volume control,
and can be mounted in an American standard 1-gang electrical
box in the wall. Up to 2 ZM-9001/9002 units can be connected to
the M-9000.
56
37
72
33
Front View
without panel
6
83.5
90 – 98
1-gang electrical box
(not supplied)
38
42
46 – 50
Figure when mounted
Dimensions of mounting opening
If the opening is too small or too large,
the ZM-9002 cannot be mounted in the
wall. Be sure to make an opening with
dimensions given above when mounting.
Unit: mm
ZM-9003 Remote Panel
120
79.4
53.3
40
70
97
127
66.4
66
7
Front View
Rear View
Side View
65.2
88
91
79
46
97
104
Dimensions of mounting opening
83.5
66
Under 250 ohms (per line)
Removable terminal block (7 pins)
-10°C to +40°C
Surface-treated steel plate, white, paint
120 (W) × 127 (H) × 53.3 (D) mm
375 g
Box mounting screw (No.6–32UNC × 30) × 4,
Box mounting screw (M4 × 30) × 4, Panel mounting screw × 2,
Removable terminal plug (7 pins) × 1
Note: If controls of more than 4 channels are needed, then additional C-001T Control Input/Output
Module is required to expand control inputs.
Since no electrical box is supplied with the unit, prepare it separately.
83.5
Bottom View
Figure when mounted
Ground the electrical
box to avoid unit
malfunction due to static
electricity.
SPECIFICATIONS
Line Resistance
Terminal
Operating Temperature
Finish
Dimensions
Weight
Accessory
46
84.2
The ZM-9003 is a remote control switch panel with 4 interlocking
selection switches and 2 momentary switches. Connecting it to the
M-9000's control input terminal permits various controls such as
BGM source selection and the sound volume adjustment.
It can be mounted in an American standard 2-gang electrical box in
the wall. Up to 2 ZM-9003 units can be connected to the M-9000.
Unit: mm
2-gang electrical box
(American type, not supplied)
91
66
99
Front View
without panel
If the opening is too small or too large, the
ZM-9003 cannot be mounted in the wall.
Be sure to make an opening with
dimensions given above when mounting.
BLOCK DIAGRAM
INTERNAL ADC / MODULE I2S
SIGNAL SELECTORS
AIN
#1
#8
I2C
ANALOG
DIGITAL
#1
#2
DIS1
DI1
1 1
2 8
1
DOUT
AIN
#2
I2C
#7
ADC
DIGITAL
DIN
MIXOUT
SLOT#4
DIN
DI1
DI2
DI3
DI4
DI1
DI2
DI3
DI4
#5
AIN
Dout 1
Dout 2
Dout 3
Dout 4
I2C
SLOT#7
5 3
6 6
DI4
7 4
8 5
ANALOG
DIS3
ANALOG
DIGITAL
DIS4
I2C
VOLUME
CONTROL
INPUT SELECT SIGNALS
CPU
KEY&DISPLAY CONTROL
I2C
MIXOUT
AIN
SLOT#8
I2C
TXDM8
TXD
RXD
RXDM8
1
2
Vacuum Fluorescent Display
R–>V
CONVERT
3
4
5
6
7
ON/OFF
8
INPUT SELECT
PRE
AMP
OUT 2
at ANALOG INPUT
at DIGITAL INPUT
Remarks
Each pair of Inputs 1 and 8, 2 and 7, 3
and 6, and 4 and 5 is the analog inputs
of ADC (Analog-Digital Converter).
So, when a digital input module such as
the D-001T is inserted into Slot 1, for
example, the digital input selector DIS1
is switched over to the DIGITAL position,
thereby disabling the use of analog
Inputs 1 and 8.
Consequently, Slot 8's analog input
(AIN) cannot be used.
Likewise, when Slot 2 is occupied by the
D-001T, Slot 7's analog input cannot be
used; and when Slot 3 is occupied, Slot
6's analog input cannot be used.
I2C
MIXOUT
DI3
H
C
E
NE5532
LPF
ADC
#7
#8
AIN
SLOT#6
3 2
4 7
EEPROM
I2C
I2C
Dout 1
Dout 2
Dout 3
Dout 4
ADC
DIGITAL
#4
Dout 1
Dout 2
Dout 3
Dout 4
MIXOUT
DI1
DI2
DI3
DI4
#6
#5
#6
AIN
SLOT#5
#3
AIN
MIXOUT
DI2
H: Hot
C: Cold
E: Earth
DSP
AIN
I2C
SLOT#3
DIS2
PRE
AMP
OUT 1
H
C
E
NE5532
VOLUME
2
ANALOG
#3
DIN
#4
MIXOUT
DAC
I2C
SLOT#2
1
2
I2C
MIXOUT
1
2
LPF
CONTROL I/O
DIN
M-9000
ADC
RXD
SLOT#1
TXD
MIXOUT
INPUT VOLUME
ON/OFF
OUTPUT SEL
OUTPUT VOLUME
MEMORY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
UTILITY
ENTER
PARAMETER
ESC/BACK
POWER
232RXD
232TXD
RXD
H
E
H
E
CI1
CI2
CI3
CI4
E
CO1
CO2
CO3
CO4
E
POWER SUPPLY
REMT-VOL1
REMT-VOL2
+VCC
–VCC
MAIN_TRANS
CONTROL
INPUT
POWER AMP
+24 V
–24 V
AC IN
+6 V
CONTROL
OUTPUT
ANALOG
DSP/AD/DA
+3.3 VBU
CPU
SUB_TRANS (EXCEPT M-9000)
–30 V
AC5 V VFD
AC5 V
RS232
TXD
MODE
MODE SW
MATRIX/MIXER
ARCHITECTURAL AND ENGINEERING SPECIFICATIONS
The digital matrix mixer shall use digital signal processing for all mixing and signal
processing functions and shall be modular for flexibility in system configuration. The
mixer shall have a frequency response from 20 Hz to 20 kHz, 3 dB.
the power is turned off and back on. A power on mode setting shall allow selection
of whether to revert to the last used preset event at power on, and if not, which
preset event is to be active at power on.
The digital matrix mixer shall utilize a modular architecture and be capable of up to
eight input channels and eight output channels. Eight module ports shall be
provided. Module ports shall include four digital input ports and three digital output
ports. Each digital input port shall accept two input channels and each digital output
port shall provide up to two output channels. All eight module ports shall accept
analog input modules and shall support control I/O function modules and analog
output modules. The mixer shall have eight independent mixing busses. Balanced
line output connections for mix busses 1 and 2 shall be provided on the rear panel.
Security features shall include a key-lock setting to selectively disable user changes
to input, output, and/or utility settings. Input and output channels shall be selectable
for user lock-out on an individual channel-by-channel basis. Password protection of
the lock-out settings shall be available by the use of a user-selected password. The
digital matrix mixer shall have a built-in RS-232 port for connection to a Windowsbased computer for storage and retrieval of setup information and for connection to
third-party ascii-based serial control systems. Software to enable PC-based data
storage and retrieval shall be provided free of charge. Stored information shall
include all software-based settings. The RS-232 port and software shall also
provide for future FLASH upgrades of the software-based feature set.
All software-based settings shall be accessible from the front panel controls. Thirtytwo FLASH memory presets shall be available to store event or scene data.
Programming of the mixer input/output routing and digital processor settings shall
be event-based. Each input channel shall support event-based [or scene-based]
programming of the following settings: channel priority, ducking on/off status,
ducking depth, input to output routing, and remote contact activation. Up to 8
priority levels shall be available. Inputs assigned to the same priority level shall
operate according to one of three selectable logic rules: First in, first out (FIFO);
Last in, first out (LIFO); or mixing.
Input channels equipped with a dedicated input module shall support event-based
[or scene-based] programming of the following settings: channel priority, ducking
on/off status, ducking depth, input to output routing, remote contact activation, VOX
trigger threshold, high and low pass filters, 10-band parametric equalization,
compression, bass and treble, and loudness compensation. Each built-in output
channel and each output channel equipped with a dedicated in/out module shall
support event-based [or scene-based] programming of the following settings: high
and low pass filters, 10-band parametric equalization, compression, bass and
treble, loudness compensation, and pre-programmed speaker equalization
settings.
A power off mode setting shall allow selection of whether input and output volume
settings revert to pre-programmed default levels or retain the last used setting after
Four control contact inputs shall allow event activation by remote dry contact
closure. The function of each control input shall be software assignable activate
Event, Volume Up/Down (Input or Output), Mute (Input or Output), Power On/Off,
Emergency Mute or Synch On/Off Control inputs shall be expandable to twelve with
a dedicated in/out control module.
Four open-collector control outputs shall allow triggering of external equipment
based on event status. The function of each control output shall be software
assignable using front panel controls.
Each of two remote volume control channels shall be assignable to allow the
volume of any one input or output channel to be remotely controlled using a 10k
ohm linear taper potentiometer or a DC control voltage varying over the range of 0
to 10 volts.
Each built-in output channel shall be transformer isolated and shall meet or exceed
the following specifications: Output impedance: 600 ohms, balanced; output level: 0
dBV nominal, where 0 dBV = 1 volt; frequency response: 20 Hz to 20 kHz (+1, -3
dB); output distortion: 0.008%, measured at 1 kHz at dBV output (where 0 dBV = 1
volt) with 22 kHz low pass filter; output connector: 4-pin removable terminal block.
Dimensions shall be 482.6(W) x 132.6(H) x 320(D) mm and weight shall be 6 kg.
TOA Corporation
www.toa.jp
Specifications are subject to change without notice.
Printed in Japan (0711) 833-52-377-4A u
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising