TOA | C-BC100T | manual | TOA C-BC100T User manual

TOA C-BC100T User manual
INSTRUCTION MANUAL
CEILING SUSPENSION BRACKET
C-BC100T
Please follow the instructions in this manual to obtain the optimum results from this unit.
We also recommend that you keep this manual handy for future reference.
SAFETY PRECAUTIONS
• Be sure to read the instructions in this section carefully
before use.
• Make sure to observe the instructions in this manual as
the conventions of safety symbols and messages
regarded as very important precautions are included.
• We also recommend you keep this instruction manual
handy for future reference.
Safety Symbol and Message Conventions
Safety symbols and messages described below are used
in this manual to prevent bodily injury and property
damage which could result from mishandling. Before
operating your product, read this manual first so you are
thoroughly aware of the potential safety hazards as well as
understand the safety symbols and messages.
WARNING
Indicates a potentially hazardous
situation which, if mishandled, could result in death or
serious personal injury.
CAUTION Indicates a potentially hazardous
situation which, if mishandled, could result in moderate or
minor personal injury, and/or property damage.
WARNING
When Installing the Unit
• Install the unit only in a location that can structurally
support the weight of the unit and the ceiling suspension
bracket. Doing otherwise may result in the unit falling
down and causing personal injury and/or property
damage.
• Do not use other methods than specified to mount the
bracket. Extreme force is applied to the unit and the unit
could fall off, possibly resulting in personal injuries.
• Ensure all screws are tightened. The unit may fall off if
insufficiently secured, resulting in possible personal
injury.
CAUTION
When Installing the Unit
• To prevent fires, electric shock, personal injury or
damage to property, refer all repairs to the dealer from
whom the unit was purchased. Installation also requires
extensive technical knowledge and experience.
• Avoid installing the unit in locations exposed to sea
breezes or corrosive gas. Mounts may become corroded,
eventually causing the unit to fall off, which could result
in personal injury.
• Have the unit periodically inspected by the dealer. If
screws or other metal parts become excessively rusty,
the unit could fall off, potentially causing personal injury.
When the Unit is in Use
• Do not stand or sit on, nor hang down from the unit as
this may cause it to fall down or drop, resulting in
personal injury and/or property damage.
GENERAL DESCRIPTION
The C-BC100T is made of stainless steel and is used to
hang TOA's outdoor camera housings C-CH100 and CCH100FH from a ceiling.
HANDLING PRECAUTIONS
• Ensure that nuts and bolts are fully loosened when
adjusting the camera's horizontal or vertical direction.
Failure to do this could damage movable sections or
cause their paint to peel off.
• Use suitable nuts and bolts for the construction and
material of the ceiling when hanging the unit from the
ceiling. (Nuts and bolts for ceiling suspension are not
supplied with the unit.)
• To clean the unit, wipe with a soft cloth dipped in a
neutral cleanser. Never use benzine, thinner or other
volatile liquids. The unit's case may be deformed or its
finish discolored.
INSTALLATION
1. Using
suitable nuts and
bolts, secure the bracket to
the ceiling at four places.
6. Horizontal angle adjustment
Loosen four bolts. After
adjusting the horizontal angle,
retighten the bolts.
5. Using another supplied housing
mounting bolt, secure the
housing to the bracket.
Safety wire fixing hole
Housing mounting bolt
Hexagonal M6 bolt with captive
washer
3. Push the bolt in the bracket's hole,
then pull the housing forward till the
bolt fits in the hole.
4. Tighten
7. Vertical angle adjustment
Loosen two hexagonal M6 bolts
on the sides. After adjusting the
vertical angle, retighten the
bolts.
the bolt to secure the
housing.
2. Insert the supplied housing mounting
Camera housing top panel
bolt into the mounting hole in the
housing top panel so that the bolt
protrudes about 3 mm.
Housing mounting hole
Note: The vertical angle adjustment bolts are loosely set when the unit is shipped from the factory.
Be sure they are securely tightened after mounting the housing.
DIMENSIONAL DIAGRAM
SPECIFICATIONS
80
100
Maximum Load
Weight
Installation Place
4-ø8.5
10
65
ø31.8
200
30
80
100
10 kg
Indoor and outdoor ceiling surfaces
(except those in shore and industrial
areas where the unit becomes
corroded, and those on the heights
exposed to strong winds)
Adjustable Bracket Horizontal: 360°
Head Angle
Vertical: 60° (up) – 60° (down)
Finish
Stainless steel, off white
Dimensions
100 (W) x 295 (H) x 100 (D) mm
Weigh
830 g
Usable Housings
C-CH100 and C-CH100FH
Note: The design and specifications are subject to change
without notice for improvement.
70
90
• Accessory
Unit: mm
Housing mounting bolt ................................ 2 set
ø7
URL: http://www.toa.jp/
133-05-314-8B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising