TOA | C-BC711W | manual | TOA C-BC711W User manual

TOA C-BC711W User manual
INSTRUCTION MANUAL
WALL MOUNTING BRACKET
C-BC711W
Thank you for purchasing TOA’s Wall Mounting
Bracket.
Please carefully follow the instructions in this
manual to ensure long, trouble-free use of your
equipment.
1. SAFETY PRECAUTIONS
• Be sure to read the instructions in this section carefully before use.
• Make sure to observe the instructions in this manual as the conventions of safety symbols and messages
regarded as very important precautions are included.
• We also recommend you keep this instruction manual handy for future reference.
WARNING
Indicates a potentially hazardous situation which, if mishandled, could
result in death or serious personal injury.
• Install the unit only in a location that can structurally support the weight of the unit and the mounting bracket.
Doing otherwise may result in the unit falling down and causing personal injury and/or property damage.
• Do not install the unit in the following locations to avoid a traffic accident or personal injury:
· Locations which block the driving of a car or somebody’s passage.
· Locations where the traffic signal or road sign is hard to be seen.
• Avoid installing or mounting the unit in unstable locations, such as on a rickety table or a slanted surface.
Doing so may result in the unit falling down and causing personal injury and/or property damage.
• Use the dedicated mounting bracket. The unit could fall off, possibly resulting in personal injuries when other
bracket than dedicated is used.
WARNING
Indicates a potentially hazardous situation which, if mishandled, could
result in death or serious personal injury.
When Installing the Unit
• Do not use any methods other than specified to mount the bracket. Extreme force is applied to the unit and
the unit could fall off, possibly resulting in personal injuries.
• Attach the safety wire to the unit. If not attached, the unit could fall off, resulting in personal injury.
• Use nuts and bolts that are appropriate for the ceiling’s or wall’s structure and composition. Failure to do so
may cause the unit to fall, resulting in material damage and possible personal injury.
• Tighten each nut and bolt securely. Ensure that the bracket has no loose joints after installation to prevent
accidents that could result in personal injury.
• Avoid installing the unit in locations exposed to sea breeze or corrosive gas. Mounts may become corroded,
eventually causing the unit to fall off, which could result in personal injury.
• Do not mount the unit in locations exposed to constant vibration. The mounting screws and/or bolts may be
loosened by excessive vibration, potentially causing the unit to fall, which could result in personal injury.
• To prevent lightning strikes, install the unit at least five meters away from a lightning rod, and yet within the
protective range (angle of 45°) of the lightning conductor. Lightning strikes may cause a fire, electric shock
or personal injury.
• When installing the unit in the snowy area, take appropriate measures to prevent snow from lying on the
unit. If the snow lies on the unit, the unit may fall, causing personal injuries.
• Be sure that at least two persons are available to install the unit. Failure to do so could result in personal
injury.
• Avoid installing the unit at heights exceeding 16 meters above the ground since the unit could be exposed to
unexpected strong winds that might cause it to fall or result in other accidents.
When the Unit is in Use
• Do not touch the unit during thunder and lightning, as this may result in electric shock.
2
CAUTION
Indicates a potentially hazardous situation which, if mishandled, could
result in moderate or minor personal injury, and/or property damage.
When Installing the Unit
• Refer all installation work to the dealer from whom the unit was purchased. Installation requires extensive
technical knowledge and experience. Failure to do so may cause electric shocks or personal injury.
• To avoid electric shocks, be sure to switch off the power before power supply wiring work.
When the Unit is in Use
• Do not stand or sit on, nor hang down from the unit as this may cause it to fall down or drop, resulting in
personal injury and/or property damage.
• Have the unit checked periodically by the shop from where it was purchased. Failure to do so may result in
corrosion or damage to the unit or its mounting brackets that could cause the unit to fall, possibly causing
personal injury.
2. GENERAL DESCRIPTION
The C-BC711W Wall Mounting Bracket is designed to be used to mount TOA’s C-CC714 and C-CC764
Outdoor Combination Camera on a wall. It can mount the Camera on a pole using the optional C-BC711PM
Pole Mounting Bracket, and YS-60B Mounting Band.
3. HANDLING PRECAUTIONS
• Mount the unit to a concrete wall or robustly constructed wall surface that can sufficiently withstand the
weight of the units. When mounting the units to a pole, pay special attention to the sway and strength of the
pole, and mount it securely at an appropriate height that will not cause the pole to sway and possibly
weaken it. Moreover, avoid mounting the units to a pole on which other objects susceptible to wind are also
mounted.
• Bolts and nuts for wall mounting are not supplied with the unit. Prepare suitable bolts and nuts keeping the
wall’s structure and material, gross weight, etc in mind.
• Do not install the unit in locations exposed to constant vibration. Do not install the unit in a vehicle nor ship.
• Avoid installing the units on sea or shore, or in locations exposed to corrosive gas, herbicides or other
sprayed liquid chemicals, or extraordinary combustible conditions.
• To prevent the unit falls off, be sure to hang the safety wire first when installing the unit.
• Outdoor-use combination cameras are designed solely for suspended installations. The dome must be
suspended vertically with its dome facing downward. Use special care not to suspend it at a tilted angle.
• Do not give vibration or shock to the unit. The mounting bracket can be damaged or fallen down.
3
4. INSTALLATION
Be sure to refer to the instruction
manual supplied with the Camera.
Wall Mounting Bracket
C-BC711W
Nut *2
Spring washer *2
Washer *2
Hexagon socket bolt
Safety wire *1
Top cover
Anchor bolt *2
M8, M10 or W 3/8
Camera mounting screw
(accessory)
e
rfac
su
all
W
Safety wire
for camera unit *1
Housing
Safety wire
for dome cover *1
Camera unit
Notes:
*1 Be sure to attach the Housing and the
Camera after hanging the safety wire.
*2 Washers, spring washers, nuts and
anchor bolts are not supplied and should
be acquired separately.
Dome cover
Accessory:
Camera mounting screw (M5 x 12 with
washer) .....3
5. SPECIFICATIONS
Finish
Base: aluminum, Light gray, paint
Dimensions
Weight
Pipe: SUS304
140 (W) x 240 (H) x 188.1 (D) mm
1.3 kg
Note: The design and specifications are subject to change without notice for improvement.
Printed in Japan
133-12-944-10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising