TOA CC-5131B User manual

TOA CC-5131B User manual
 TOA Model CC-5131B is a camera selector that not only permits a maximum of 6 CCTV surveillance
cameras to be remotely selected but also turns on and off power supplied to the cameras. The
+ CC-5131B is designed for use with the CC-5111B Remote Control Unit and the CC-5120 Relay Box. ~~
Avoid exposing unit to sunlight and never place unit near or over a
heat register as this may have a bad effect on the case or parts,
Avoid exposing unit to moisture or dust. When water enters, a
breakage or shock hazard can be caused.
"Never disassemble unit and touch the inside or insert metallic stuff
into the inside as this may lead to a breakage or shock hazard.
Wipe down with a soft cloth when cleaning the exterior of unit.
Never use such volatile liquids as thinner and benzine because their
use may discolor or deform unit.
Я RISK OF ELECTRIC SHOCK |
DC NOT OPEN .
TO REDUCE THE RISK OF ELECTRICAL
- SHOCK, DO NOT REMOVE COVER. |
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SER-
VICE PERSONNEL.
. AUTO/MANUAL CHANGEOVER SWITCH (AUTO)
Pressing this swich when the Sequential Switcher (CC-31118,
CC-3121B, CC-3211B and CC-3221B is connected to the
CC-5131B permits video inputs to be automatically switched. In
this event, no remote operations avalilable from the CC-5111B8
Remote Control Unit are impossible.
, CAMERA SELECTOR SWITCHES (CAMERA SITE) *
The swich to selet the camera to be operated.
. CAMERA POWER SWITCHES (CAMERA POWER)
The swich to pewer each camera, Be sure to switch power off
for cameras not to be used. ;
. REMOTE UNIT CONNECTION TERMINAL (COM OUT)
Connect to the COM terminal of the CC-5111B Remote Control
Unit.
. COM EXT TERMINAL
For extension of the CC-5131B unit. Refer to the Section
” Extension” :
10.
11,
12.
RELAY BOX COM CONNECTION TERMINALS (COM IN)
Connect to the COM terminal of the Relay Box (CC-5120)
conneced to each camera.
SPOT OUTPUT CONTROL. TERMINALS (SPOT)
Connect to the remote connector of the Sequential Switcher
(CC-3111B,CC-3121B,CC-3211B and CC-3221B)
CAMRA POWER CONTROL TERMINALS (CAMERA)
Connect to the CAMERA-IN terminal of the Relay Box (CC-5120)
connected to each camera.
VIDEO OUTPUT TERMINAL (VIDEO OUT)
Connect to a monitor,
VIDEO EXT TERMINAL
For extension of the CC-5131B unit. Refer to the Section
"Extension"
VIDEO INPUT TERMINALS (VIDEO IN)
Connect to video output from each camera.
EARTH TERMINAL
required for mounting the CCTV
equipment in an equipment rack.
Remove rubber supporters from the
equipment,
Attach the kit to the equipment.
Screw
Hack mounting kit
MB-15B(optional)
CC-5120 Relay Box No, 1
3x8 Tapping
poussa
6
DE-COM
1815
FOCUS
Z00M IS]
>
onrac |||)
WIPER
| [O]
DOWN
RIGHT
LEFT
‘ото | O)
camera ||]
кой
COMTROL UNT
PLACE,
LECT
ALTO
WEED
DEFRO-
w Th Th
CAMERA f
=
TALLY ]
LN
Seele ee ee
CC-5120 Relay Box No. 6
To each connection terminal
of Relay Box No. 2
oon
DC-COM
{RIS
FOCUS
zoom O
"
ON-AC IS
WIPER
E ER O]
up
DOWN
RIGHT
LEFT
AUTO
camena | [[@]]
e]
ac-con e
TO REMOTE
CONTROL MAT
[IH]
CLOSE
OPEN
HEAR
SE
H
т
=
Fi
1D
Fu
DICHT
LEFT
ALL
WIPER
DEFRO.
LGAMESA |
TALLY |
epep
CC-5111B Remote Control Unit
[ PAN [HLT [2004 FOCUS” [IRIS
preg free Je ficar fe pl Kr
aACIOIOA CAE A A|A|A| AO
paa Puta Ed] bd EA A] E A Eo ELLE |
Y CAMERA PET WIFER AUTO LEFT RIGHT DOWN LE TELE WIDE NHAR FER OPEN CLOSE 3
]
=
©]
=)
2
= ||
=
>
|
= X
CC-5131B
oy EXT a 4 5 6 6 AUTO 20 4 5 € Poo Зо | MES OUT (ee IN
Peer’ OxO. ©. ©
Öle o lee oo eo elek oe Ox O. y. Y 5
PA A e TO [6 (0 10
—
J
a J dl J lh: |) J ) J
To COM terminal of each Relay Box To CAMERA terminal of each Relay Box
J
ай
J
=]
Camera No. 1
' PO
0000 t |
Monitor { | ||
eCONNECTION OF THE CC-5131 TO SEQUENTIAL SWITCHER CC-3111 OR CC-3211 Camera No. 6
| CC-5131B
cou cou Г cos m ; ] £ mo т ¿Por TS L FG EM] VIDED OUT pr VIDEO IN ee
delelpiglelaaleiaieiele e|A|PE Cela Ale CÍAIO Ox O. O. ©,
ll lla © © 6 Ô
To COM terminal of the Remote
Control Unit {CC-5111B)
a . } — ``. \ А A \ =
To COM terminal of each Relay Box (CC-5120) To CAMERA terminal of each Relay Box (CC-5120)
| ое
BOE)
® т. ® © ® 16-pn connector supplied with the Sequential Switcher
NET
Sequential SwitcherCC-3111B
a E SELECFEO bid VIDED IH
0009
Monitor | | — J
Camera No. 1 : J
|
== ‘
Camera No, 6
— Remarks:
(1) Since the Sequential Switcher is remotely controlled in the above connection, its spot selector switch does
not work.
(2) Change the connector setting inside the Sequential Switcher through reference to the section “To
qualified servic personnel” in operating instruction manual for the Sequential Switcher.
Camera No, 1
Camera No. 6
||
00000
Monitor
Camera Selector A
To COM terminal
of the Remote
Control Unit (CC-5111B) To CAMERA terminal of Relay
Box (CC-5120) of No. 1 through No. 6
To COM terminal of Relay
Box (CC-5120) of No. 1
through No. 6
Camera Selector 8
г — оО W—— mac;
To CAMERA terminal
— To COM terminal of Relay Box (CC-5120) of Relay Box (CC-5120)
of No, 7 through No. 12 of No. 7 through No. 12
Camera No. 7 | Caméra No, 12
Note: When the Sequential Switcher CC-3221 or CC-3221 is involved, refer to the section "Connection of the CC-5131 to Sequential
Switcher CC-3111 or CC-3211 of this operating instruction manual for major connections,
(1) Connect between the 16-pin connector supplied with the Sequential Switcher and each of the “A”, “B” and “SPOT” terminals.
SPOT terminal number SPOT terminat number
® 1 O
® 2 ®
a з @
® ®
® ®
® ®
®
® * Alphabet tn circle (O) stands for
each camera selector number,
(2) Connect between the “AUTO” terminal of the camera selector A and the “G” terminal of the camera selector B.
REMARKS:
(1) Since the Sequential Switcher is remotely controlled, its spot selector switch does not work.
(2) Change the connector setting inside the Sequential Switcher through reference to the section “Function of the Remote Control
Connector, Part 2” in operating instruction manual for the Sequential Switcher.
®OPERATION WHEN THE SELECTOR IS EXTENDED Camera Selector A
1. Operater in a normal manner when selecting camera No.1 ws es sty tt es
through No.6. ® 000000 000000
2. When selecting camera No. 7 through No.12 ©
OPlace the AUTO/MANUAL switch of the camera Camera Selector 8
po! A In the ON position. о a
Set to ON the CAMERA SITE: switch of the camera = LA DAA
selector B which corresponds to the camera you wish О 0 65000
to select. The above example shows that camera No.9
has been selected. Camera Selector A
3. When auto sequence is needed using the Sequential Fi ous —
Switcher CC-3121B or CC-3221B. ы
ФРасе the both AUTO/MANUAL switches of the © 000000 cooo0€
camera selector À and B in the ON position. Camera Selector B
aro FM Fo MA]
o 000000 200006
Remarks:
@ stands for the Ostands for the
switch in the ON switch in the OFF
position. position,
Control output: 6 make-contact outputs for turning the Weight: 5.3 Ibs (2.4 kg)
cameras on or off, Finish: Panel: Semi-glazed melamine baked paint-
6 make-contact outputs for selecting the ing (Black)
cameras to be controlled remotely plus 1 Case: Semi-glazed melamine baked paint-
output for extending the camera selector. ing (dark grey)
6 make-contact outputs for selecting the Assessories
cameras to be monitored plus 1 output for Operating InstrUCtIONS ..…….rrserrerrnenennsenneennennssnnnnnnn 1
auto-switching. Warranty card (for U.S. specifications only) ccc 1
Video inputs: 6 inputs for composite video signal 1.0Vp-p — *Specifications are subject to change without notice for improve-
plus 1 input for extending the camera ment.
selector.
(All inputs excepting the selected input are
terminated with 75 ohms.)
Video outputs: 1 output with composite video signal 1.0Vp-p
plus 1 output for extending the camera
selector, » 4 ‘
Ambient operating © A TOA Corporation
temperature: + 14°F to 122°F (—10°C to 50°C) indoor use TOA
Dimensions: 16.5"(W) x 1.8"(H) x 10.0"(D)
(420 x 44.5 x 253 mm) 133-12-376-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement