TOA | F-122CU | manual | TOA F-122CU User manual

TOA F-122CU User manual
INSTRUCTION MANUAL
CEILING SPEAKER SYSTEM
F-122CU
Thank you for purchasing TOA’s Ceiling Speaker System.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
TABLE OF CONTENTS
1. SAFETY PRECAUTIONS ............................................................................... 3
2. GENERAL DESCRIPTION ............................................................................. 3
3. FEATURES .......................................................................................................... 4
4. NOMENCLATURE AND DIMENSIONS ..................................................... 4
5. MOUNTING HARDWARE INSTALLATION ............................................... 5
6. WIRING
6.1. Using the Speaker in UL1480 Category UUMW .............................................. 9
6.2. Using the Speaker in UL1480 Category UEAY and
CAN/CSA C22.2 No.205 Category UEAY7
6.2.1. Wiring through hard or flexible conduit ................................................. 10
6.2.2. Wiring with naked cables ...................................................................... 11
7. CABLE CONNECTION TO INPUT CONNECTOR ................................. 12
8. SPEAKER INSTALLATION ........................................................................... 13
9. REMOVING THE SPEAKER FOR MAINTENANCE
9.1. Detaching the Front Grille ............................................................................... 15
9.2. Removing the Speaker ................................................................................... 15
10. REPAINTING THE SPEAKER ...................................................................... 16
11. INPUT OVERLOAD PROTECTION FUNCTION .................................... 16
12. SAFETY AGENCY COMPLIANCE
12.1. Setting to the Following Positions .................................................................. 17
12.2. Setting to 8 Ω Position .................................................................................... 17
13. SPECIFICATIONS ............................................................................................ 18
Accessories ............................................................................................................. 18
Optional Component ................................................................................................ 18
2
1. SAFETY PRECAUTIONS
• Be sure to read the instructions in this section carefully before use.
• Make sure to observe the instructions in this manual as the conventions of safety symbols and messages
regarded as very important precautions are included.
• We also recommend you keep this instruction manual handy for future reference.
Safety Symbol and Message Conventions
Safety symbols and messages described below are used in this manual to prevent bodily injury and property
damage which could result from mishandling. Before operating your product, read this manual first and
understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.
WARNING
Indicates a potentially hazardous situation which, if mishandled, could
result in death or serious personal injury.
CAUTION
Indicates a potentially hazardous situation which, if mishandled, could
result in moderate or minor personal injury, and/or property damage.
WARNING
• Use the specified mounting hardware in
combination. Doing otherwise may cause the unit
or component to fall off, resulting in personal injury.
• Leave the installation to your TOA dealer because
the installation requires expert knowledge.
Improper installation may cause the unit to fall,
resulting in personal injury and/or property
damage.
• Should the following irregularity be found during
use, immediately stop operating the unit and
contact your nearest TOA dealer. Further attempt
to use under this condition may cause fire or
electric shock.
• Install the unit in a location that can structurally
support the weight of the unit and its mounting
hardware. Doing otherwise may result in the unit
falling down and causing personal injury and/or
property damage.
· If you detect smoke or a strange smell coming
from the unit
· If no tone sounds
• Do not use other methods than specified to mount
the unit. Extreme force is applied to the unit and
the unit could fall off, possibly resulting in personal
injuries.
• Attach the safety wire to the unit. If not attached,
the unit could fall off, resulting in personal injury.
• Tighten each screw securely. Ensure that the unit
has no loose joints after installation to prevent
accidents that could result in personal injury.
CAUTION
• Avoid installing the unit in humid or dusty locations,
in locations exposed to the direct sunlight, near the
heaters, or in locations generating sooty smoke or
steam as doing otherwise may result in fire or
electric shock.
• Do not operate the unit for an extended period of
time with the sound distorting. This is an indication
of a malfunction, which in turn can cause heat to
generate and result in a fire.
• Never hold the diffuser section as a handle to carry
the unit during installation. If the diffuser breaks off,
the unit could fall from an elevated position,
resulting in possible personal injury.
2. GENERAL DESCRIPTION
The F-122CU is a flush-mounted ceiling speaker that offers a wide frequency range of high-quality sound
output. Use of its supplied mounting hardware and optional HY-TB1 Tile Bar Bridge permits it to be versatilely
mounted to match a wide range of applications and installation locations.
3
3. FEATURES
• Bass-reflex speaker system designed to provide a wide frequency range and high power handling capability.
• Wide-dispersion flush-mount ceiling speaker design employs unique acoustic construction to realize a wide
area of coverage. Uniform sound output levels are achievable not only directly under the speaker, but also
over a wide radius.
• Because the speaker is provided with both low- and high-impedance operating capability, it can be used in
many different applications. Front panel-mounted input selector switch permits easy verification and change
of current impedance settings.
• Easy installation. Can be quickly and accurately mounted to ceilings.
• Rotating front grille can be installed quickly and conveniently.
• Attractive exterior design specially created by an interior designer blends naturally with any architectural
space, enhancing the immediate area's sense of harmony.
4. NOMENCLATURE AND DIMENSIONS
Unit: mm (inches)
ø195 (7 43/64)
[Side]
ø230 (9 1/16)
[Front]
Approx. 600 (23 5/8)
40 (1 37/64)
Front grille (accessory)
238 (9 3/8)
[Rear]
Safety wire hook
Safety wire (accessory)
Ceiling reinforcement ring
(accessory)
Mounting hole: ø200 (7 7/8)
Ceiling panel
4
Max. 202 (7 61/64)
[Ceiling mounting]
Choke bracket
Max. 37 (1 29/64)
Connector cover
5. MOUNTING HARDWARE INSTALLATION
Before mounting the speaker, determine the most appropriate method for the existing ceiling structure.
Be sure to use an optional HY-TB1 Tile Bar Bridge in combination with the supplied ceiling
reinforcement ring.
[Installation view on Drop Ceilings]
Because the bridge rails are 603 mm (23 47/64") in length, be sure to match them to the ceiling tile size during
installation.
Caution
Set the bridge rails so that both ends fit securely into the T-grids, even if the ceiling tile accidentally falls off.
Reinforcement ring mounting screw
Tie-plate
(preinstalled on Bridge rail)
Tie-plate mounting screw
T-grid
Ceiling tile
Bridge rail
HY-TB1
(optional)
Ceiling reinforcement ring (accessory)
[Installation view on Dry Wall Ceilings]
Caution
Only install the Tile Bar Bridge on ceiling frames that can structurally support the weight of the speaker(s).
Reinforcement ring mounting screw
Tie-plate mounting screw
Tie-plate
(preinstalled on Bridge rail)
Bridge rail
HY-TB1
(optional)
Ceiling frame
Ceiling panel
Ceiling reinforcement ring (accessory)
5
Step 1. Cut a ø200 mm (7 7/8") hole in the ceiling.
ø200 ±5 mm (7 7/8 ±13/64")
Use the supplied paper pattern to position and trace the hole.
Ceiling panel
Step 2. Install the HY-TB1 in the ceiling.
Loosen the two reinforcement ring mounting screws in each tie-plate to the point that they do not fall
out of their holes.
Tie-plate
HY-TB1
(optional)
Bridge rail
Tie-plate mounting screw
Reinforcement ring mounting screws
(Leave these screws loose.)
[For Drop Ceiling]
HY-TB1 (optional)
2-foot tile
• Mounting to 2-foot tiles
Align the two bridge rails as shown in the figure
at right.
T-grid
HY-TB1 (optional)
600 mm tile
• Mounting to 600 mm tiles
Align the two bridge rails diagonally at an angle
of 10° – 15°.
10° – 15°
T-grid
6
Step 3. Place the supplied reinforcement ring on the ceiling panel.
Fold the reinforcement ring in half* and insert it
through the mounting hole in the ceiling panel,
then open it with its tabs facing up.
Place the ring on the ceiling panel aligning it
with the mounting hole.
Mounting hole
* The reinforcement ring is too large to be
inserted into the mounting hole unless folded.
Ceiling reinforcement ring
(accessory)
Reinforcement ring placed on the ceiling panel
These tabs must
face upward,
away from the hole.
Step 4. Attach the ceiling reinforcement ring to
each tie-plate using 2 reinforcement ring
mounting screws.
Reinforcement ring mounting screw
1
Tie-plate
Ceiling reinforcement ring
2
Fit closely to the back surface
of the ceiling panel.
If the ceiling reinforcement ring does not line
up accurately with the ceiling mounting hole,
adjust its position by either loosening the tieplate mounting screws and sliding the tieplate into correct position, or by shifting the
tie-plate mounting screws to the appropriate
holes in the Tile Bridge rails.
The ceiling reinforcement ring can be moved
in the direction indicated by the arrows.
Note
Be sure to tighten the tie-plate mounting
screws after completing the adjustment.
Tie-plate mounting screw
Tie-plate
Ceiling reinforcement ring
7
Step 5. Attach a safety wire to prevent the speaker from accidentally falling.
To attach, tie one end of the supplied safety wire around the speaker's safety wire hook, and tie its
snap ring around the installed HY-TB1 or a solid structure.
Note
When there is no gap between the bridge rails and the ceiling panel, to secure the safety wire, tie the
wire around a solid structure (pipe, building frame, etc.).
Safety wire (accessory)
Ceiling reinforcement ring
(accessory)
Ceiling frame
HY-TB1 (optional)
Ceiling panel
Safety wire (accessory)
Safety wire hook
Speaker unit
8
6. WIRING
6.1. Using the Speaker in UL1480 Category UUMW
Choke bracket
Remove the choke bracket and the cover plate
from the speaker.
Cover plate
Note
The removed choke bracket is not used.
Flexible metal conduit (3/8" or 1/2")
Cover plate
Conduit fitting
To install this speaker as a fire alarm signaling
service UUMW, use flexible conduit of 3/8 or 1/2
inch trade size and the UL514B listed conduit
fitting of the same trade size.
Detachable input connector
Mount the conduit fitting to the cover plate.
Connect the conduit to the fitting, and wire the
detachable input connector.
(For wiring the input connector, refer to p. 12.)
Replace the cover plate to the speaker.
Plug the wired input connector into the speaker's
socket.
Connector cover
After completing the speaker cable connection, turn the connector cover
in the direction indicated by the arrow, and fix the cover with 2 screws.
9
6.2. Using the Speaker in UL1480 Category UEAY and
CAN/CSA C22.2 No.205 Category UEAY7
6.2.1. Wiring through hard or flexible conduit
Note
The choke bracket equipped with the speaker has not been evaluated by UL, for conduit connection and
UL514B Standard.
Flexible conduit of 3/8 or 1/2 inch trade size and the UL514B conduit fitting of the same trade size can also be
used. For the method of conduit connection, refer to p. 9.
Loosen the screw to allow the speaker cable to pass through.
Flexible conduit
Choke bracket
Plug the wired input connector into the speaker's socket,
then pull the speaker cable from the choke bracket.
(For wiring the input connector, refer to p. 12.)
Accommodating larger diameter conduit
The choke bracket accommodates up to 3/8-inch
(9.5 mm) flexible conduit. When larger diameter
conduit should be fit, use a suitable fitting
commercially available by replacing the existing
choke bracket with it. Detaching the choke
bracket by unscrewing it exposes a 7/8-inch (22
mm) hole. Install the alternate fitting there.
Retighten the screw to fix
the flexible conduit.
Note
Ensure that the flexible conduit is securely fixed.
Connector cover
After completing the speaker cable connection, turn the connector cover
in the direction indicated by the arrow, and fix the cover with 2 screws.
10
6.2.2. Wiring with naked cables
Loosen the screw to allow the speaker cable to pass through.
Choke bracket
Retighten the screw to fix
the speaker cable.
Plug the wired input connector into the speaker's socket,
then pull the speaker cable from the choke bracket.
(For wiring the input connector, refer to p. 12.)
Note
Ensure that the speaker cable is securely fixed.
Connector cover
After completing the speaker cable connection, turn the connector cover
in the direction indicated by the arrow, and fix the cover with 2 screws.
11
7. CABLE CONNECTION TO INPUT CONNECTOR
Recommended cable types
• Solid copper wire:
ø1.0 – ø1.6 mm
(equivalent to AWG 18 – 14)
• Stranded copper wire: 0.75 – 2.5 mm2
(equivalent to AWG 18 – 14)
Cover mounting screw
Step 1. Loosen the 2 cover mounting screws, and rotate the
connector cover in the direction indicated by the
arrow in the figure at right.
Speaker unit
Connector cover
Detachable input
connector
Step 2. Remove the detachable input connector from the
speaker's socket, and loosen the screw of the
terminal to be used.
Speaker unit
Step 3. Insert the stripped cable end into the terminal and tighten the terminal screw with a screwdriver.
[If not bridging]
Caution
If not making bridge connections,
be sure to tighten unused terminal
screws to avoid their vibration.
[If bridging]
From Amplifier
5 mm
(13/64")
To the
next speaker
12
8. SPEAKER INSTALLATION
Caution
Before mounting, check to be sure that the speaker's
3 mounting tabs are turned inside the unit as shown
in the figure.
If turned outward, the speaker cannot be inserted
through the mounting hole.
In
Out
Mounting tab
Step 1. Insert the speaker through the mounting hole till it
contacts the ceiling panel. While doing so, avoid
directly touching the speaker's diffuser section.
Mounting hole
WARNING
Never hold the diffuser section as a handle to
carry the speaker during installation. If the
diffuser breaks off, the unit could fall from an
elevated position, resulting in possible
personal injury.
Speaker unit
Diffuser section
Diffuser section
Step 2. Rotate and tighten the mounting tab axis screws (3 places) on the unit clockwise to their full stop in
order to grip the ceiling panel with the mounting tabs.
Mounting tab
Mounting tab axis screw
Use an electric screwdriver to tighten.
(Tightening torque: 6 – 10 kgf·cm)
13
Step 3. Set the input power.
Turn the input selector switch (on the unit's front) to
set it to the desired input impedance.
(Factory-preset to 170 Ω.)
F-122CU
IMP. 70VLINE 25VLINE
8Ω
Note
Setting position "8 Ω" can be used in UL1480
Category UEAY and CAN/CSA C22.2 No.205
Category UEAY7.
Step 4. Attach the front grille.
Align the tabs (3 places) on the back side of the grille
with the corresponding notches in the unit, then rotate
the grille to full stop in the direction indicated by the
"LOCK" arrow.
NC
10kΩ
0.5W
0.06W
3.3kΩ
1.5W
0.2W
1kΩ
5W
0.6W
330Ω
15W
1.9W
170Ω
30W
3.7W
Speaker unit
Tip
The front grille employs a double-locking system that
clicks into place once partway through rotation, but
only locks into position at its point of full rotation.
Always be sure to rotate the grille to its full stop.
Notch (3 places)
LOCK
Front grille (accessory)
14
Tab (3 places)
9. REMOVING THE SPEAKER FOR MAINTENANCE
9.1. Detaching the Front Grille
1
Turn the front grille counterclockwise to full stop, then lightly
pull it downward.
Tip
The front grille employs a double-locking system.
If the grille cannot be detached when lightly pulled downward,
it likely has not yet been fully rotated back to the detachment
position. In such cases, take care to rotate the grill fully
counterclockwise in order to release the lock.
Unlock
Front grille
2
Pull lightly.
9.2. Removing the Speaker
Rotate the 3 mounting tab axis screws counterclockwise. The mounting tabs rise as they turn, allowing the
speaker to be removed.
Caution
When loosening the mounting tab axis screws, support the speaker by hand to prevent it from falling.
Screw cap
Mounting tab
Mounting tab axis screw
Use an electric screwdriver to detach.
Caution
Be sure to set the screwdriver's torque for under 4 kgf·cm.
Failure to do so may cause the Screw cap and the Mounting tab to fall off
on the rear of ceiling panel.
15
10. REPAINTING THE SPEAKER
Follow the procedure below when repainting the front grille:
Step 1. Clean the front grille before painting.
Wipe with a soft cloth dampened in a detergent.
Caution
Do not use thinner or other volatile liquids to clean the grille.
Step 2. Spray on a uniform, thin coat of paint.
Cautions
• Avoid painting with a roller or brush, as the grille mesh holes could become clogged with paint.
• Use appropriate spray paints for the front grille (grille and frame) materials.
Grille: Rolled steel plate
Frame: Fire-resistant ABS resin (acrylic paint)
• Be sure to follow the directions indicated on the paint when painting.
Step 3. After the paint has dried, apply another light coat.
Caution
Repeating Step 2, apply two or more light coats of paint.
Application of one thick coat of paint all at once may cause drips or unevenness to show up in the
painted finish, or clog the mesh holes.
11. INPUT OVERLOAD PROTECTION FUNCTION
The F-122CU features an internal input overload protection circuitry. If an extremely high input level is fed to
the unit, the protection circuitry automatically cuts off the signal to the speaker element.
A drastic reduction in sound volume indicates that the protection circuitry has been enabled.
In such cases, simply reduce the amplifier volume. The protection circuitry will automatically reset in
approximately 10 seconds. After reset, try to maintain the volume at a level slightly lower than before.
Caution
This protection circuitry does not completely protect the unit against extremely high input power levels.
Depending on the type or duration of excessive power input, the protection circuitry might not be enabled,
resulting in damage to the speaker element. Also, if the excessive power input continues for a long period of
time, the circuitry may not be capable of resetting to its original condition.
Use the system with care so that the speakers are not exposed to excessive power input.
16
12. SAFETY AGENCY COMPLIANCE
This product is for indoor use only.
The F-122CU's front-mounted rotary switch permits selection of speaker handling power (wattage) on 25 V or
70 V line operation or low impedance (8 Ω) operation.
Depending on the switch settings, the unit complies with the different UL Categories as follows.
Note: Setting to the "8 Ω " position allows the unit to comply with Category UEAY/UEAY7.
12.1. Setting to the Following Positions
Setting Position
0.5 W
1.5 W
70 V Line
5W
15 W
30 W
0.06 W
0.2 W
25 V Line
0.6 W 1.9 W
3.7 W
[Fire protective signaling speaker, UL1480 Category UUMW]
Products Listed under this category are suitable for use in the following configurations:
a. For fire alarm signaling service in conjunction with Listed compatible emergency communication and
relocation equipment and/or fire alarm control unit, the combination of which is intended to be installed in
accordance with the applicable requirements of NFPA 72, the National Electrical Code (NEC) and the local
authority having jurisdiction.
b. For general (non-fire alarm) signaling service in conjunction with compatible Listed audio equipment, the
combination of which is intended to be installed in accordance with the applicable requirements of the
National Electrical Code (NEC) and the local authority having jurisdiction.
[Suitable for use in air-handling spaces (UL2043)]
Fire Test for Heat and Visible Smoke Release for Discrete Products and their Accessories Installed in AirHandling Spaces (1998) - NFPA 70 National Electrical Code (NEC) 2002, Article 300-22 (c) and NFPA 90A
Installation of air-conditioning and ventilation systems, section 2-3.10.1 (a) exception 3.
[Sound Pressure Level (SPL) specs]
Loudspeaker sound pressure level is measured per UL1480/ANSI-S1.12/ANSI-S1.2 in the specified
reverberant chamber.
Setting Position
dB at 10 feet
0.5 W
74 dB
70 V Line
1.5 W
5W
15 W
78 dB 83 dB 87 dB
30 W
90 dB
0.06 W
65 dB
25 V Line
0.2 W 0.6 W 1.9 W
70 dB 75 dB 79 dB
3.7 W
82 dB
12.2. Setting to 8 Ω Position
[General signaling speaker, UL1480 Category UEAY and CAN/CSA C22.2 No.205 Category UEAY7]
Products Listed under this category are suitable for use in general (non-fire alarm) signaling service in
conjunction with compatible Listed audio equipment, the combination of which is intended to be installed in
accordance with the applicable requirements of the National Electrical Code (NEC) and the local authority
having jurisdiction.
[Suitable for use in air-handling spaces (UL2043)]
Fire Test for Heat and Visible Smoke Release for Discrete Products and their Accessories Installed in AirHandling Spaces (1998) - NFPA 70 National Electrical Code (NEC) 2002, Article 300-22 (c) and NFPA 90A
Installation of air-conditioning and ventilation systems, section 2-3.10.1 (a) exception 3.
17
13. SPECIFICATIONS
Enclosure
Rated Input
Power Handling Capacity
Impedance
Frequency Response
Speaker Component
UL Code
Mounting Hole
Input Terminal
Usable Cable
Finish
Dimensions
Weight
Bass reflex type
30 W (High Impedance)
Continuous pink noise:
60 W (8 Ω)
70 V line: 170 Ω (30 W), 330 Ω (15 W), 1 kΩ (5 W), 3.3 kΩ (1.5 W),
10 kΩ (0.5 W)
25 V line: 170 Ω (3.7 W), 330 Ω (1.9 W), 1 kΩ (0.6 W), 3.3 kΩ (0.2 W),
10 kΩ (0.06 W)
8Ω
70 – 20,000 Hz
12 cm (5") cone-type
UL1480 (UUMW/UEAY), UL2043, CAN/CSA C22.2 No.205 (UEAY7)
ø200 mm (7 7/8")
Maximum ceiling thickness: 37 mm (1 29/64")
Removable locking connector with screw-down terminals
(2 input terminals and 2 bridge terminals)
Solid copper wire:
ø1.0 – ø1.6 mm (Equivalent to AWG 18 – 14)
Stranded copper wire: 0.75 – 2.5 mm2 (Equivalent to AWG 18 – 14)
Enclosure:
Steel plate, plating
Baffle:
Fire-resistant ABS resin (resin material grade: UL-94 V-0 or
its equivalent), black
Rim:
Fire-resistant ABS resin (resin material grade: UL-94 V-0 or
its equivalent), white, paint
Punching net: Steel plate, white, paint
ø230 mm (9 1/16") x Depth 238 mm (9 3/8")
3.8 kg (including mounting accessories)
Note: The design and specifications are subject to change without notice for improvement.
• Accessories
Front grille ............................................................ 1
Ceiling reinforcement ring .................................... 1
Safety wire (approx. 60 cm or 23 5/8") .................. 1
Paper pattern ....................................................... 1
• Optional Component
HY-TB1 (Tile Bar Bridge): Use this bridge when mounting the speaker unit to drop ceiling or weak dry wall
ceiling.
18
URL: http://www.toa.jp/
133-01-00185-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising