TOA F-2852C /EU User manual

TOA F-2852C /EU User manual
INSTRUCTION MANUAL
CEILING SPEAKER SYSTEM
F-2852C
TABLE OF CONTENTS
1. SAFETY PRECAUTIONS .......................... 2
7. REPAINTING THE SPEAKER .................. 10
2. GENERAL DESCRIPTION ........................ 3
8. ABOUT THE INPUT OVERLOAD
PROTECTION CIRCUITRY ...................... 10
3. FEATURES ................................................. 3
4. NOMENCLATURE AND DIMENSIONS .... 4
5. INSTALLATION .......................................... 5
9. SPECIFICATIONS ..................................... 11
Accessories ............................................... 11
Optional Components ................................ 11
6. REMOVING THE SPEAKER
FOR MAINTENANCE ................................. 9
Thank you for purchasing TOA’s Ceiling Speaker System.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
1. SAFETY PRECAUTIONS
• Be sure to read the instructions in this section carefully before use.
• Make sure to observe the instructions in this manual as the conventions of safety symbols and messages
regarded as very important precautions are included.
• We also recommend you keep this instruction manual handy for future reference.
Safety Symbol and Message Conventions
Safety symbols and messages described below are used in this manual to prevent bodily injury and property
damage which could result from mishandling. Before operating your product, read this manual first and
understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.
WARNING
Indicates a potentially hazardous situation which, if mishandled, could
result in death or serious personal injury.
CAUTION
Indicates a potentially hazardous situation which, if mishandled, could
result in moderate or minor personal injury, and/or property damage.
WARNING
• Leave the installation to your TOA dealer because
the installation requires expert knowledge.
Improper installation may cause the unit to fall,
resulting in personal injury and/or property
damage.
• Should the following irregularity be found during
use, immediately stop operating the unit and
contact your nearest TOA dealer. Further attempt
to use under this condition may cause fire or
electric shock.
• Install the unit in a location that can structurally
support the weight of the unit and its mounting
hardware. Doing otherwise may result in the unit
falling down and causing personal injury and/or
property damage.
· If you detect smoke or a strange smell coming
from the unit
· If no tone sounds
• Do not use other methods than specified to mount
the unit. Extreme force is applied to the unit and
the unit could fall off, possibly resulting in personal
injuries.
• Attach the safety wire to the unit. If not attached,
the unit could fall off, resulting in personal injury.
2
• Use the specified mounting hardware in
combination. Doing otherwise may cause the unit
or component to fall off, resulting in personal injury.
CAUTION
• Avoid installing the unit in humid or dusty locations,
in locations exposed to the direct sunlight, near the
heaters, or in locations generating sooty smoke or
steam as doing otherwise may result in fire or
electric shock.
• Tighten each screw securely. Ensure that the unit
has no loose joints after installation to prevent
accidents that could result in personal injury.
• Do not operate the unit for an extended period of
time with the sound distorting. This is an indication
of a malfunction, which in turn can cause heat to
generate and result in a fire.
• Do not hold the tweeter as a handle to carry the
unit. If the tweeter breaks off, the unit falls off,
resulting in possible personal injury.
• Avoid touching the unit's sharp metal edge to
prevent injury.
2. GENERAL DESCRIPTION
The F-2852C is a 2-way, flush-mounted ceiling speaker that offers a wide frequency range and high-quality
sound output.
Use of its supplied and optional mounting hardware permits versatile mounting to match a wide range of
applications and installation locations.
3. FEATURES
• Two-way, bass-reflex speaker system designed to provide a wide frequency range and high power handling
capability.
• Ideal for locations that have high ceilings or require true-to-life sounds.
• Uniform sound output levels are achievable not only in the position directly under the speaker, but also over
a wide radius. (Coverage angle is approximately 110°.)
• Because the speaker is provided with both low- and high-impedance operating capability, it can be used in
many different applications. Front panel-mounted input selector switch permits easy verification and change
of current impedance settings, even after installation.
• Easy installation. Can be quickly and accurately mounted to ceilings.
• Rotating front grille can be installed quickly and conveniently.
• Attractive exterior design specially created by an interior designer blends naturally with any architectural
space, enhancing the immediate area's sense of harmony.
• Optional mounting hardware permits installation in weak ceiling panels.
3
4. NOMENCLATURE AND DIMENSIONS
Unit: mm (inches)
ø245 (9 41/64)
[Side]
Front grille (accessory)
Approx. 600 (23 5/8)
ø280 (11 1/32)
[Front]
38 (1 1/2)
227 (8 15/16)
[Rear]
Cord clamp
Ceiling reinforcement ring
(accessory)
Mounting hole: ø250 (9 27/32)
Ceiling panel
4
Max. 200 (7 7/8)
[Ceiling mounting]
Detachable input connector
Max. 37 (1 29/64)
Safety wire hook
Safety wire (accessory)
5. INSTALLATION
The F-2852C ceiling speaker can be mounted in 3 different configurations:
• Direct mounting to a ceiling panel
Use the supplied ceiling reinforcement ring.
• Mounting to a ceiling frame
Use the supplied ceiling reinforcement ring in conjunction with the optional HY-TB1 Tile Bar Bridge.
• Mounting to an anchor bolt
Use the supplied ceiling reinforcement ring in conjunction with the optional HY-AH1 Anchor Hanging
Bracket.
Mount the speaker using the most appropriate method for the ceiling panel or installation location.
Step 1. Cut a ø250 mm (9 27/32") hole in the ceiling.
Use the supplied paper pattern to position and trace the hole.
ø250 ±5 mm (9 27/32 ±13/64")
Ceiling panel
Step 2. Connect the speaker cable to the detachable input connector.
Tip
The following matching cable types are recommended:
• Solid copper wire:
ø0.5 – ø1.6 mm (equivalent to AWG 24 – 14)
• Stranded copper wire: 0.2 – 2.5 mm2 (equivalent to AWG 24 – 14)
Detachable input
connector
Speaker unit
2-1. Remove the detachable input connector from the
speaker's wiring socket, and loosen the screw of the
terminal to be used.
2-2. Insert the stripped cable end into the terminal and tighten the terminal screw with a screwdriver.
[If not bridging]
Caution
If not making bridge connections,
be sure to tighten unused terminal
screws to avoid their vibration.
[If bridging]
From Amplifier
5 mm
(13/64")
To the
next speaker
5
Step 3. Install mounting hardware on the ceiling.
3-1. Direct mounting to a ceiling panel
Mounting hole
Fold the supplied ceiling reinforcement ring in half*
and insert it through the mounting hole in the
ceiling panel, then open it with its tabs facing up.
Place the ring on the ceiling panel aligning it with
the mounting hole.
* The reinforcement ring is too large to be inserted
into the mounting hole unless folded.
Ceiling reinforcement ring
(accessory)
Reinforcement ring placed on ceiling panel
These tabs must
face upward,
away from the hole.
3-2. Mounting to a ceiling frame
Use the supplied ceiling reinforcement ring in conjunction with the optional HY-TB1 Tile Bar Bridge.
Note
Refer to the instruction manual included with the HY-TB1 for the correct ceiling mounting procedure.
[Installed HY-TB1]
HY-TB1 (optional)
Ceiling reinforcement ring (accessory)
Ceiling panel
Ceiling frame
3-3. Mounting to an anchor bolt
[Installed HY-AH1]
Use the supplied ceiling reinforcement ring in
conjunction with the optional HY-AH1 Anchor
Hanging Bracket.
Note
Refer to the instruction manual included with the
HY-AH1 for the correct mounting procedure.
Anchor bolt
Ceiling
reinforcement ring
(accessory)
HY-AH1 (optional)
Ceiling panel
Step 4. Attach a safety wire to prevent the speaker from accidentally falling.
To attach, tie one end of the supplied
safety wire around the speaker's safety
wire hook, and tie its snap ring around
a secure C-channel bar or anchor bolt
in the ceiling.
Safety wire
(accessory)
Secure C-channel bar or
anchor bolt in the ceiling
Safety wire hook
Speaker unit
6
Step 5. Make speaker cable connection.
5-1. Plug the wired detachable input connector into the speaker's wiring socket.
5-2. Fix the speaker cable with the cord clamp.
Loosen the cord clamp fixing screws and open the cord clamp.
Then, pass the speaker cable between both screws.
Clamp fixing screw (2 pieces)
Speaker cable
Cord clamp
Detachable input
connector
5-1
Cord clamp
Tighten the clamp fixing screws to
fix the speaker cable with the cord clamp.
5-2
Confirm the connector will not pull out.
Pull on the cable here to confirm that
speaker cable is securely fixed.
Detachable input connector
Speaker unit
Step 6. Mount the speaker.
Caution
Before mounting, check to be sure that the speaker's
4 mounting tabs are turned inside the unit as shown in
the figure.
If turned outward, the speaker cannot be inserted
through the mounting hole.
In
Out
Mounting tab
6-1. Insert the speaker through the mounting hole till it contacts the ceiling panel.
While doing so, avoid directly touching the speaker's
diaphragm and tweeter.
Mounting hole
WARNING
Never grab the tweeter section as a hand hold.
The speaker could fall due to damage, resulting
in possible personal injury.
Tweeter section
Tweeter section
7
6-2. Rotate and tighten the mounting tab axis screws (4 places) on the unit clockwise to their full stop in
order to grip the ceiling panel with the mounting tabs.
Mounting tab
Mounting tab axis screw
Use an electric screwdriver to tighten.
(Tightening torque: 6 – 10 kgf·cm)
Step 7. Set the input power.
Turn the input selector switch (on the unit's front) to set it to the desired input impedance using a slotted
screwdriver.
Note: The switch is factory-preset to 170 Ω.
Input selector switch
Speaker's front
Slotted screwdriver
Important
Never set this switch to low impedance (8 Ω) when using a high impedance 25, 70, or 100 V line. Failure
to follow this instruction could result in damage to the speaker or amplifier.
Step 8. Attach the front grille.
Align the tabs (4 places) on the back side of the
grille with the corresponding notches in the unit,
then rotate the grille to full stop in the direction
indicated by the "LOCK" arrow.
Speaker
unit
Tip
The front grille employs a double-locking system
that clicks into place once partway through
rotation, but only locks into position at its point of
full rotation. Always be sure to rotate the grille to
its full stop.
Notch (4 places)
LOCK
Front grille (accessory)
8
Tab (4 places)
6. REMOVING THE SPEAKER FOR MAINTENANCE
6.1. Detaching the Front Grille
1
Turn the front grille counterclockwise to full stop, then lightly
pull it downward.
Tip
The front grille employs a double-locking system.
If the grille cannot be detached when lightly pulled downward,
it likely has not yet been fully rotated back to the detachment
position. In such cases, take care to rotate the grill fully
counterclockwise in order to release the lock.
Unlock
Front grille
2
Pull lightly.
6.2. Removing the Speaker
Rotate the 4 mounting tab axis screws counterclockwise. The mounting tabs rise as they turn, allowing the
speaker to be removed.
Caution
When loosening the mounting tab axis screws, support the speaker by hand to prevent it from falling.
Screw cap
Mounting tab
Mounting tab axis screw
Use an electric screwdriver to detach.
Caution
Be sure to set the screwdriver's torque for under 4 kgf·cm.
Failure to do so may cause the Screw cap and the Mounting tab to fall off
on the rear of ceiling panel.
9
7. REPAINTING THE SPEAKER
Follow the procedure below when repainting the front grille:
Step 1. Clean the front grille before painting.
Wipe with a soft cloth dampened in a detergent.
Caution
Do not use thinner or other volatile liquids to clean the grille.
Step 2. Spray on a uniform, thin coat of paint.
Cautions
• Avoid painting with a roller or brush, as the grille mesh holes could become clogged with paint.
• Use appropriate spray paints for the front grille (grille and frame) materials.
Grille: Rolled steel plate
Frame: Fire-resistant ABS resin (acrylic paint)
• Be sure to follow the directions indicated on the paint when painting.
Step 3. After the paint has dried, apply another light coat.
Caution
Repeating Step 2, apply two or more light coats of paint.
Application of one thick coat of paint all at once may cause drips or unevenness to show up in the
painted finish, or clog the mesh holes.
8. ABOUT THE INPUT OVERLOAD PROTECTION CIRCUITRY
The F-2852C features internal input overload protection circuitry. If an extremely high input level is fed to the
unit, the protection circuitry automatically cuts off the signal to the speaker element.
A drastic reduction in sound volume indicates that the protection circuitry has been enabled.
In such cases, simply reduce the amplifier volume. The protection circuitry will automatically reset in
approximately 10 seconds. After reset, try to maintain the volume at a level slightly lower than before.
Caution
This protection circuitry does not completely protect the unit against extremely high input power levels.
Depending on the type or duration of excessive power input, the protection circuitry might not be enabled,
resulting in damage to the speaker element. Also, if the excessive power input continues for a long period of
time, the circuitry may not be capable of resetting to its original condition.
Use the system with care so that the speakers are not exposed to excessive power input.
10
9. SPECIFICATIONS
Enclosure
Rated Input
Power Handling Capacity
Impedance
Sound Pressure Level
Frequency Response
Speaker Component
Mounting Hole
Input Terminal
Usable Cable
Finish
Dimensions
Weight
Bass reflex type
60 W (High Impedance)
Continuous pink noise: 90 W (8 Ω)
Continuous program: 180 W (8 Ω)
100 V line: 170 Ω (60 W), 330 Ω (30 W), 670 Ω (15 W), 3.3 kΩ (3 W)
70 V line: 83 Ω (60 W), 170 Ω (30 W), 330 Ω (15 W), 670 Ω (7.5 W),
3.3 kΩ (1.5 W)
25 V line: 83 Ω (7.5 W), 170 Ω (3.7 W), 330 Ω (1.9 W), 670 Ω (0.9 W),
3.3 kΩ (0.2 W)
8Ω
91 dB (1 W, 1 m)
60 – 20,000 Hz (–10 dB), 45 – 20,000 Hz (–20 dB)
at installation in 1/2 free sound field
(Measured by installing the unit in the center of a ceiling.)
High frequency: Dome-type, Low frequency: 16 cm (6 1/2") cone-type
ø250 mm (9 27/32")
Maximum ceiling thickness: 37 mm (1 29/64")
Removable locking connector with screw-down terminals
(2 input terminals and 2 bridge terminals)
Solid copper wire:
ø0.5 – ø1.6 mm (equivalent to AWG 24 – 14)
Stranded copper wire: 0.2 – 2.5 mm2 (equivalent to AWG 24 – 14)
Enclosure:
Steel plate, plating
Baffle:
Fire-resistant ABS resin (resin material grade: UL-94 V-0 or its
equivalent), black
Rim:
Fire-resistant ABS resin (resin material grade: UL-94 V-0 or its
equivalent), white, paint
Punched net: Steel plate, white, paint
ø280 mm (11 1/32") x Depth 227 mm (8 15/16")
5.1 kg (including mounting accessories)
Note: The design and specifications are subject to change without notice for improvement.
• Accessories
Front grille ...................................................
Ceiling reinforcement ring ..........................
Safety wire (approx. 60 cm or 23 5/8") ........
Paper pattern ..............................................
1
1
1
1
• Optional Components
HY-TB1 (Tile Bar Bridge):
lace this bridge on the ceiling frame when mounting the speaker unit to a
P
weak suspended ceiling.
HY-AH1 (Anchor Hanging Bracket): Attach this bracket to an anchor bolt when mounting the speaker unit to a
weak ceiling.
11
Traceability Information for Europe
Manufacturer:
TOA Corporation
7-2-1, Minatojima-Nakamachi, Chuo-ku, Kobe, Hyogo,
Japan
Authorized representative:
TOA Electronics Europe GmbH
Suederstrasse 282, 20537 Hamburg,
Germany
URL: http://www.toa.jp/
133-01-00187-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement