TOA | H-1 | manual | TOA H-1 User manual

TOA H-1 User manual
OPERATING INSTRUCTIONS
SPEAKER SYSTEM
Please follow the instructions in this manual to obtain the optimum results from this unit.
We also recommend that you keep this manual handy for future reference.
TABLE OF CONTENTS
1. SAFETY PRECAUTIONS ............................................................................................... 2
2. GENERAL DESCRIPTION ............................................................................................ 3
3. FEATURES ......................................................................................................................... 3
4. NOMENCLATURE ............................................................................................................ 4
5. INSTALLATION
5.1. Direct Wall/Ceiling Mounting Without Using an Electrical Box ........................................ 5
5.2. Mounting the Speaker to an Electrical Box Using The Adapter Frame ........................... 8
5.3. Mounting the Speaker Directly to an Electrical Box ......................................................... 9
5.4. Removing the Trim Piece ................................................................................................ 9
6. REPAINTING THE GRILLE AND TRIM PIECE ..................................................... 10
7. PROTECTION CIRCUITRY INFORMATION .......................................................... 11
8. EQUALIZATION .............................................................................................................. 11
9. SPECIFICATIONS .......................................................................................................... 12
Accessories .......................................................................................................................... 12
H-1
1. SAFETY PRECAUTIONS
• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe
operation.
• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or
cautions regarding safety.
• After reading, keep this manual handy for future reference.
Safety Symbol and Message Conventions
Safety symbols and messages described below are used in this manual to prevent bodily injury and property
damage which could result from mishandling. Before operating your product, read this manual first and
understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.
WARNING
Indicates a potentially hazardous situation which, if mishandled, could
result in death or serious personal injury.
CAUTION
Indicates a potentially hazardous situation which, if mishandled, could
result in moderate or minor personal injury, and/or property damage.
WARNING
• Install the unit only in a location that can
structurally support the weight of the unit and the
mounting bracket. Doing otherwise may result in
the unit falling down and causing personal injury
and/or property damage.
• Use nuts and bolts that are appropriate for the
ceiling's or wall's material and structure. Tighten
each nut and bolt securely. Ensure that the bracket
has no loose joints after installation to prevent
accidents that could result in personal injury.
• Since the unit is designed for in-door use, do not
install it outdoors. If installed outdoors, the aging of
parts causes the unit to fall off, resulting in
personal injury. Also, when it gets wet with rain,
there is a danger of electric shock.
• Do not apply lubricant and rust inhibitor. If it
contacts resin or rubber parts, they could
deteriorate and cause the unit to fall, possibly
resulting in personal injury.
2
CAUTION
• Avoid touching the unit's sharp metal edge to
prevent injury.
• Do not operate the unit for an extended period of
time with the sound distorting. This is an indication
of a malfunction, which in turn can cause heat to
generate and result in fire.
2. GENERAL DESCRIPTION
TOA's H-1 is a cylinder-shaped, small flush-mount 2-way speaker featuring high sound quality.
3. FEATURES
• The H-1 Speaker System features, flush-mount speaker design with a rotatable cylinder-type enclosure. The
speaker's smooth curved surface allows it to blend in with the interiors of most modern buildings.
• The speaker's small (8 x 5 cm) woofer featuring high input capacity ensures powerful sound reproduction.
• The one-inch balanced dome tweeter features ferro-fluid to ensure superb transient response characteristics
for clear, high frequency sound output and high power-handling capabilities.
• The speaker's built-in crossover network circuitry features sharp cut-off characteristics that realize uniform
energy radiation while suppressing unwanted input signals to the woofer or tweeter.
• The H-1 Speaker System is designed with an emphasis on installation ease and safety, as well as easier
conduit wiring when an electrical box is installed.
• The cylinder-shaped speaker's mounting angle can be easily adjusted for up to ±45 degrees rotation.
• A built-in matching transformer permits the speaker to be used for both high- and low-impedance
applications. For low-impedance applications, either the 4 Ω or 16 Ω terminal can be selected. Impedance
can be easily changed from outside the unit.
• Detachable screw terminals facilitate connection. Dual positive and negative terminals also facilitate bridge
connections.
• Both the speaker enclosure and Trim Piece are made of fire-resistant ABS (UL Standard 94: V-0 Grade).
• All external parts have been specially selected for ease of refinishing and repainting.
3
4. NOMENCLATURE
[Front Panel]
[Side Panel]
[Side Panel]
126
H-1 speaker
Grille
[Side Panel]
Trim Piece
44
46
312
230.8
For mounting to the Adapter Panel
[Rear Panel]
Mounting bracket
66.7
(2 5/8")
54
55.6
(2 3/16")
For mounting to an electrical box
Connector for impedance selection
255.6 (10 1/10")
Detachable input connector
254 (10")
• Accessory (Adapter Panel)
287.2
10
66.7
(2 5/8")
55.6
(2 3/16")
54
122
230.8 (For mounting the H-1 speaker)
255.6 (10 1/10") (For mounting to an electrical box)
254 (10") (For mounting to an electrical box)
Unit : mm
4
5. INSTALLATION
5.1. Direct Wall/Ceiling Mounting Without Using an Electrical Box
Step 1. Adapter Panel mounting
1-1. Using the supplied hole pattern sheet as a guide,
make an opening of the specified size in the wall or
ceiling panel.
287.2 (Adapter Panel)
Note
The thickness of the suitable wall or ceiling panel is 9
to 30 mm.
98
(Mounting hole)
122 (Adapter Panel)
268 (Mounting hole)
1-2. Loosen the two board clamp screws.
Board clamp
1-3. Place the Adapter Panel inside the opening, and set
the panel to the desired position using the positioning
tabs.
Adapter Panel
Positioning tab
5
1-4. Clamp the wall or ceiling panel using the two board
clamps, and secure with the clamp screws.
Step 2. Wiring and impedance changes
2-1. Pull the cables out of the mounting hole in the wall or
ceiling, then strip the insulation back about 5mm from
the cable ends.
Note
Usable cable: Solid cable or stranded cable (0.2 mm2
- 2.5 mm2) (Corresponding to AWG No.
24 - 14)
About 5 mm
2-2. Remove the detachable input connector from the
speaker, then loosen the connector screws with a
small slot screwdriver.
2-3. Insert the stripped cable ends into the input
connector, and tighten the connector screws.
• When not bridging
connections
Note
When not bridging connections, be sure to also
tighten the screws of the terminals not in use to avoid
vibration or rattling noise.
• When bridging
connections
From amplifier
To next
speaker
6
2-4. Attach two impedance selector sockets to the
connector to select the desired impedance. Preset to
830 Ω (12 W for 100 V line and 6 W for 70 V line).
Note
The speaker is designed to be used for both 70 V and
100 V line applications. When using the 100 V line,
do not select the "420 Ω" impedance, since the
speaker itself or power amplifier may be damaged.
• When selecting 4 Ω
• When selecting 16 Ω
• When selecting 830 Ω
(preset by the factory)
Impedance selector socket
2-5. Insert the detachable input connector into the
speaker socket.
Step 3. Mounting the speaker and Trim Piece
3-1. Align the four inward-facing holes in the speaker's
mounting bracket with the corresponding holes in the
Adapter Panel mounting tabs, then mount the
speaker to the panel using the four supplied screws
(M4 x 25 screws with both the spring washers and
plain washers).
Adapter Panel
H-1 speaker
7
3-2. Loosen the angle adjustment screws. After adjusting
the angle, retighten the screws.
Tip
The mounting angle can be adjusted for up to ±45°.
Since the mounting bracket is marked with mounting
angles at 15° intervals, use this marking as a guide
when adjusting the angle.
45°
90゜
15゜
15゜
15
゜
45°
Stud screw
Angle adjustment screw
3-3. Align the two securing clips on the Trim Piece with
the speaker's two stud screws, then push the Trim
Piece onto the speaker until the Trim Piece is snug to
the wall or ceiling surface.
H-1 speaker
Securing clip
Trim Piece
Stud screw
5.2. Mounting the Speaker to an Electrical Box Using The Adapter Panel
The H-1 speaker system can be mounted to walls or ceilings using an electrical box*. Mount the Adapter
Panel to the electrical box as shown below. Further mounting procedures are the same as detailed in Steps 2
and 3.
* Distance between mounting holes (A) x (B):
254 mm (10") x 66.7 mm (2 5/8") or
255.6 mm (10 1/10") x 55.6 mm (2 3/16")
(A)
Electrical box
(B)
Adapter Panel
H-1 speaker
Memo
Electrical box mounting screws are attached to the H-1 speaker.
8
5.3. Mounting the Speaker Directly to an Electrical Box
The H1 speaker system can also be mounted directly to an electrical box*. Follow Steps 2 and 3 for
instructions. In this case, use the outward-facing holes in the mounting bracket when mounting to the wall or
ceiling.
* Distance between mounting holes (A) x (B): 254 mm (10") x 66.7 mm (2 5/8") or
255.6 mm (10 1/10") x 55.6 mm (2 3/16")
(A)
Electrical box
Memo
Electrical box mounting screws are
attached to the H-1 speaker.
(B)
H-1 speaker
Note: The distance between the wall or ceiling surface and the box bottom surface must be 45 mm or more.
When using the Raco 953 electrical box, be careful in installation because it is shallow.
45 mm or more
5.4. Removing the Trim Piece
When removing the Trim Piece for maintenance or repair,
squeeze its sides by hand to create a gap between the
Trim Piece and wall/ceiling, then insert a screwdriver blade
into the gap and pry off the piece.
Caution
If you raise either right or left side of the Trim Piece by
force, it may be broken. Pull the both sides out evenly and
gradually.
9
6. REPAINTING THE GRILLE AND TRIM PIECE
Follow the procedures below to change the color of the
grille.
1. Remove the speaker's angle adjustment screw (1
piece).
2. Detach either of the two mounting brackets attached to
the speaker.
Mounting bracket
Angle adjustment screw
Grille mounting screw
3. Remove the two grille mounting screws from the back of
the speaker.
4. Slide the grille off the speaker.
5. Paint both the grille and Trim Piece.
5-1. Wipe dirt off the grille and Trim Piece with a soft cloth
moistened with a detergent before painting. Do not
use volatile liquids such as thinner.
5-2. Uniformly spray a thin coating of paint over the grille
and Trim Piece changing the spraying positions
gradually.
Notes
• Do not use a roller or brush to paint because the
meshes of the grille could be clogged with paint.
• Use paint that is appropriate for the composition of
the grille and Trim Piece.
Grille:
Rolled steel plate
Trim Piece: Fire-resistant ABS resin
• Follow the instructions on the paint when painting.
5-3. After the paint dries, repeat Step 5-2 once or twice to
repaint.
Notes
• Be sure to repeat Step 5-2 at least twice.
• When repainting the front grille, place the grille
upside down so that the surface is painted uniformly.
6. After the paint has dried, remount the grille to the
speaker.
10
Grille
7. Attach the grille to the speaker with its two mounting
screws.
8. Reattach the mounting bracket to the speaker with the
angle adjustment screw.
7. PROTECTION CIRCUITRY INFORMATION
• The speaker has built-in overload protection circuitry.
If there is an extremely high level input signal to the speaker, the overload protection circuitry is activated
and cuts off the signal input to the speaker component.
• A sudden drop of the sound volume level during speaker operation indicates that the overload protection
circuitry has been activated. In such a case, reduce the amplifier volume and wait. The protection circuitry is
automatically reset after approximately 10 seconds. After the circuitry is reset, set the volume at a lower
level than before.
Important Note
This overload protection circuitry does not completely protect the speaker component. Depending on the
nature of the excessive signal applied to the loudspeaker, there may be damage to the loudspeaker
components before the protection circuitry can operate. Also, depending on the duration of the excessive input
signal, the protection circuitry may be damaged and will not recover. Take special care that the excessive
input is not applied to the speaker during use.
8. EQUALIZATION
• The H-1 is designed to provide good quality sound without additional equalization. However, by equalizing it
as shown below, sounds can be made more powerful and intelligible.
• Using a digital signal processor, make the following equalization setting.
[When not using a subwoofer]
[dB]
Filter
HPF
PEQ
PEQ
PEQ
LPF
Frequency
Gain
118 Hz
125 Hz
+10 dB
220 Hz
- 6.5 dB
5 kHz
+ 1.5 dB
15.8 kHz
Q
Q 0.707
Q 1.800
Q 1.414
Q 0.305
Q 0.500
+20
+10
0
-10
-20
-30
-40
20
50
100
500
1k
5k
10k
[When using a subwoofer]
Filter
HPF
PEQ
PEQ
PEQ
LPF
Frequency
Gain
118 Hz
125 Hz
+ 4 dB
220 Hz
- 6.5 dB
5 kHz
+ 1.5 dB
15.8 kHz
20k
[Hz]
Frequency - Gain
[dB]
Q
Q 0.707
Q 1.800
Q 1.414
Q 0.305
Q 0.500
+20
+10
0
-10
-20
-30
-40
20
50
100
500
Frequency - Gain
1k
5k
10k
20k
[Hz]
11
9. SPECIFICATIONS
Enclosure Type
Power Handling
Rated Input
Rated Impedance
Sensitivity
Frequency Response
Crossover Frequency
Speaker Component
Input Terminal
Usable Cable
Finish
Dimensions
Weight
Sealed type
90 W (continuous program input, 4 Ω loaded)
30 W (continuous pink noise input, 4 Ω loaded)*1
12 W (16 Ω or high impedance)
4 Ω, 16 Ω
70 V line: 0420 Ω (12 W), 830 Ω (6 W), 1.7 kΩ (3 W), 3.3 kΩ (1.5 W)
100 V line: 830 Ω (12 W), 1.7 kΩ (6 W), 3.3 kΩ (3 W)
85 dB (1 W, 1m, 2 π loading)*2
120 Hz to 20 kHz (–10 dB, 2 π loading)
5,000 Hz
Low frequency: 8 cm x 5 cm cone woofer
High frequency: Balanced dome tweeter
Detachable screw terminal, (+)/(-) 2 each (for bridging connection)
Solid cable or stranded cable: 0.2 mm2 – 2.5 mm2 (Corresponding to
AWG No. 24 – 14)
Enclosure:
Fire-resistant ABS resin (UL 94V-0), black
Trim Piece:
Fire-resistant ABS resin (UL 94V-0), white, paint
Grille:
Rolled steel plate, white, paint
Adapter Panel: Stainless steel
312 (w) x 126 (h) x 90 (d) mm
1.5 kg (including Adapter Panel)
*1 Continuous 24 hours, band-limited pink noise (50 to 20,000 Hz)
*2 Pink noise (1,000 Hz to 10,000 Hz)
Note: The design and specifications are subject to change without notice for improvement.
• Accessories
Adapter Panel ......................................... 1
Pattern paper .......................................... 1
Speaker mounting screw
M4 x 25 (with spring washer and
plain washer) ...................................... 4
Electrical box mounting screw
M4 x 25 ............................................... 4
UNC No. 8-32 x 32 mm ....................... 4
Spring washer ..................................... 4
Plain washer ....................................... 4
Traceability Information for Europe
Manufacturer:
TOA Corporation
7-2-1, Minatojima-Nakamachi, Chuo-ku, Kobe, Hyogo,
Japan
Authorized representative:
TOA Electronics Europe GmbH
Suederstrasse 282, 20537 Hamburg,
Germany
URL: http://www.toa.jp/
533-06-075-1B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising