TOA | HY-0852ST | manual | TOA HY-0852ST User manual

INSTRUCTION MANUAL
SPEAKER MOUNTING BRACKET
HY-0851ST
HY-0852ST
Please follow the instructions in this manual to obtain the optimum results from this unit.
We also recommend that you keep this manual handy for future reference.
SAFETY PRECAUTIONS
• Do not loosen an axial bolt to prevent accidents that
• Be sure to read the instructions in this section carefully
could result in personal injury. (For the axial bolt, refer to
the section "NOMENCLATURE".)
• Make sure to observe the instructions in this manual as
• Do not hang down from the bracket, as the speaker
before use.
the conventions of safety symbols and messages
regarded as very important precautions are included.
• We also recommend you keep this instruction manual
handy for future reference.
Safety Symbol and Message Conventions
Safety symbols and messages described below are used
in this manual to prevent bodily injury and property
damage which could result from mishandling. Before
operating your product, read this manual first so you are
thoroughly aware of the potential safety hazards as well as
understand the safety symbols and messages.
WARNING Indicates a potentially hazardous
situation which, if mishandled, could result in death or
serious personal injury.
• Install the unit only in a location that can structurally
support the weight of the unit and the mounting bracket.
Doing otherwise may result in the speaker falling down
and causing personal injury and/or property damage.
• Owing to the speaker's size and weight, be sure that at
least two persons are available to install the speaker.
Failure to do so could result in personal injury.
• Be sure to follow these instructions closely when
installing the HY-0851ST or HY-0852ST bracket to
prevent falls of the bracket due to corrosion, etc., which
could result in personal injury.
· Because the HY-0851ST and HY-0852ST cannot be
used alone, be sure they are installed in combination
with another specified bracket.
· The HY-0801ST and HY-0852ST are designed for
indoor use only. Do not install outdoors.
• Tighten each nut and bolt securely. Ensure that the HY0851ST and HY-0852ST have no loose joints after
installation to prevent accidents that could result in
personal injury.
system and bracket could fall, resulting in personal
injury.
GENERAL DESCRIPTION
The HY-0851ST and HY-0852ST Speaker Mounting
Brackets are specially designed for mounting TOA's ES0851 Speaker System. Use these brackets in combination
with their optional speaker mounting brackets HY-B0801,
HY-C0801 or HY-W0801. The HY-0851ST bracket can be
used in combination with the optional speaker stand ST-32
as well.
SPECIFICATIONS
Model Number
HY-0851ST
HY-0852ST
Finish
Rolled steel plate, paint, black, semi-mat
Weight
3.1 kg
3.4 kg
Note : The design and specifications are subject to change
without notice for improvement.
• Accessories
Hexagon bolt M8
(with spring washer and plain washer) ................ 4
DIMENSIONAL DIAGRAM
[HY-0851ST]
[HY-0852ST]
(642)
Speaker bracket
Speaker mounting plate (2 places)
Vertical angle adjustment
bolt (2 places)
Axial bolt (2 places)
214
289
352
427
397
Speaker bracket
Speaker mounting plate (2 places)
Vertical angle adjustment
bolt (2 places)
Axial bolt (2 places)
150
120
150
60
90
Stand fixing nut
(M8, 2 places)
ø50
Bracket fixing nut (M8, 4 places)
60
ø50
368.6
618.6
Adjustable vertical mounting angle range:
90° (upward-facing angle) – 90° (downward-facing angle)
Bracket fixing nut (M8, 4 places)
90
15
25
259
(392)
Unit: mm
Adjustable vertical mounting angle range:
0° (upward-facing angle) – 180° (downward-facing angle)
INSTALLATION
Figure 1
1. Remove screws (two each) on both sides of the speaker.
Supplied hexagon bolt
2. Mount the speaker bracket to the speaker. To achieve
this, align holes in the speaker mounting plate with the
speaker's holes made as the result of removing screws
in Step 1 above, then mount the plate with the supplied
hexagon bolts. (See Figure 1.)
Note : Ensure that the bracket is mounted to the
speaker by tightening the bolts at two places on
each side of the speaker (four places in total).
HY-0851ST
HY-0852ST
Figure 2
HY-C0801
HY-W0801
HY-B0801
Bracket A
Hexagon bolts supplied with
HY-B0801, HY-C0801, and
HY-W0801 (M8, 4 places)
Bracket B (part of
HY-B0801, HY-C0801,
and HY-W0801)
3. • Combination with HY-B0801, HY-C0801 or HYW0801 Mounting Bracket (See Figure 2.)
Using the four supplied hexagon bolts, attach the HY0851ST or HY-0852ST to Bracket B of the HY-B0801,
HY-C0801 or HY-W0801.
Notes
• Be sure to use and tighten all of the four supplied
hexagon bolts securely.
• For instructions as to mounting to Bracket A, ceilings,
walls or pipes, refer to the instruction manual for the HYB0801, HY-C0801 or HY-W0801.
• Combination with the ST-32 Speaker Stand
HY-0851ST, HY-0852ST
Speaker system (ES-0851)
(applicable to the HY-0851ST only) (See Figure 3.)
Insert two hexagon bolts supplied with the ST-32 into the
HY-0851ST's two openings provided for stand mounting.
Tighten these bolts to mount the HY-0851ST to the ST32 Stand referring to the ST-32's instruction manual.
Figure 3
4. Loosen the vertical angle adjustment bolt to adjust the
speaker's vertical mounting angle, then retighten the bolt
securely.
HY-0851ST
Hexagon bolts supplied
with ST-32 (2 places)
Adaptor supplied
with ST-32
ST-32
Warning
Do not loosen an axial bolt to prevent accidents that
could result in personal injury.
Axial bolt
Vertical angle adjustment bolt
Printed in Japan
133-05-315-70

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project