TOA | HY-AH1 | manual | TOA HY-AH1 User manual

TOA HY-AH1 User manual
INSTRUCTION MANUAL
ANCHOR HANGING BRACKET
HY-AH1
Please follow the instructions in this manual to obtain the optimum results from this unit.
We also recommend that you keep this manual handy for future reference.
1. SAFETY PRECAUTIONS
• Be sure to read the instructions in this section carefully before use.
• Make sure to observe the instructions in this manual as the conventions of safety symbols and messages
regarded as very important precautions are included.
• We also recommend you keep this instruction manual handy for future reference.
WARNING
Indicates a potentially hazardous situation which, if mishandled, could
result in death or serious personal injury.
• Leave the installation to your TOA dealer because the installation requires expert knowledge. Improper
installation may cause the speaker to fall, resulting in personal injury and/or property damage.
• Install the mounting hardware in a location that can structurally support the weight of the mounting hardware
and the speaker. Doing otherwise may result in the speaker falling down and causing personal injury and/or
property damage.
• Do not use other methods than specified to mount the unit. Extreme force is applied to the unit and the unit
could fall off, possibly resulting in personal injuries.
• Tighten each nut and bolt securely. Ensure that the unit has no loose joints after installation to prevent
accidents that could result in personal injury.
• Use the specified speaker in combination. Doing otherwise may cause the speaker or component to fall off,
resulting in personal injury.
CAUTION
Indicates a potentially hazardous situation which, if mishandled, could
result in moderate or minor personal injury, and/or property damage.
• Avoid touching the unit's sharp metal edge to prevent injury.
2. GENERAL DESCRIPTION
TOA's HY-AH1 Anchor Hanging Bracket is designed to be mounted to an anchor bolt to prevent the full weight
of a flush-mounted ceiling speaker from being directly applied to the ceiling panel. The ceiling reinforcement
ring which is supplied with the speaker is required when using the Anchor Hanging Bracket.
3. SPECIFICATIONS
Finish
Weight
Usable Speaker
Steel plate, plating
700 g
F-122C, F-2322C, F-2352C, F-2852C
• Accessory
Paper pattern ................................... 1
Note: The design and specifications are subject to change without notice for improvement.
4. INSTALLATION
Refer to the speaker's instruction manual for information.
Step 1. Loosen the four slot screws to adjust the HY-AH1's width.
Depending on the type of speaker to be mounted, adjust the width as shown in the figures below.
[Mounting the F-122C, F-2322C or F-2352C speaker]
[Mounting the F-2852C speaker]
Slot screws
Slot screws
Width
To shorten the width
of the bracket, push it
in the direction indicated
by the arrow to full stop.
To lengthen the width
of the bracket,
pull it in the direction
indicated by the arrow
to full stop.
Width
Note: Be sure to retighten the four slot screws after completing the width adjustment.
Step 2. Fix the Hanging Bracket to the anchor bolt.
2-1. The position of the upper anchor bolt nut
(the Hanging Bracket's mounting
position) should be 200 mm (7 7/8") from
the ceiling surface.
Mounting hole
F-122C,
F-2322C,F-2352C
F-2852C
Note: ‌Use the supplied paper pattern to
determine the position.
Anchor bolt
ø200 mm
(7 7/8")
ø250 mm
(9 27/32")
Hanging Bracket
mounting position
: 200 mm (7 7/8")
Paper pattern
(accessory)
Ceiling panel
2-2. Mount the Hanging Bracket to the anchor bolt. Be sure to securely fix using double nuts.
Note: ‌Before mounting, loosen the four reinforcement ring mounting screws to the point that they do
not fall out of their holes.
The length of the anchor bolt end must be
shorter than 26 mm (1 1/32").
If it exceeds this limit, the speaker will come
into contact with the end of the bolt,
preventing correct speaker installation.
HY-AH1
Anchor bolt
Reinforcement ring
mounting screw
(4 screws)
200 mm
(7 7/8")
Step 3. Mount the ceiling reinforcement ring (supplied with the speaker) to the Hanging Bracket.
Press the reinforcement ring firmly against the back side of the ceiling panel, and secure with the four
screws.
HY-AH1
Reinforcement ring
mounting screw
Ceiling reinforcement ring
(supplied with the speaker)
Press against the ceiling panel.
Press against
the back side of the ceiling.
URL: http://www.toa.jp/
133-01-00118-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising