TOA | HY-CM10W | manual | TOA HY-CM10W User manual

TOA HY-CM10W User manual
Note
To mount the speaker to the ceiling in a vertical orientation, use
the brackets supplied with the speaker. For more information, refer
to the instruction manual enclosed with the speaker.
3. MOUNTING DIMENSIONS
[HY-CM10B, HY-CM10W]
WARNING
9.8 x 41.8 oval hole
• Do not use other methods than specified to mount the unit.
Extreme force is applied to the unit and the speaker could fall off,
possibly resulting in personal injuries.
• Use nuts and bolts that are appropriate for the ceiling's structure
and composition. Failure to do so may cause the speaker to fall,
resulting in material damage and possible personal injury.
• Tighten each nut and bolt securely. Ensure that the unit has no
loose joints after installation to prevent accidents that could
result in personal injury.
• Use the specified speaker in combination. Doing otherwise may
cause the speaker to fall off, resulting in personal injury.
• Do not mount the unit in locations exposed to constant vibration.
The unit can be damaged by excessive vibration, potentially
causing the speaker to fall, which could result in personal injury.
• Do not use anti-rust lubricant. If it contacts resin or rubber parts,
they could deteriorate and cause the unit to fall, possibly
resulting in personal injury.
CAUTION
Indicates a potentially hazardous situation which, if
mishandled, could result in moderate or minor personal
injury, and/or property damage.
• Avoid touching the unit's sharp metal edge to prevent injury.
• Do not hang down from the unit as this may cause it to fall down
or drop, resulting in personal injury and/or property damage.
• Have the unit checked periodically by the shop from where it was
purchased. Failure to do so may result in corrosion or damage to
the unit that could cause the unit to fall, possibly causing
personal injury.
ø40
ø9.8
ø120
[HY-CM20B, HY-CM20W]
• Since the unit is designed for indoor use, do not install it
outdoors. If installed outdoors, the aging of parts causes the
speaker to fall off, resulting in personal injury.
45°
The figure above is an example
of F-1000 series installation.
Step 3. Attach the ceiling mount bracket to the ceiling using the
ceiling mounting holes.
[HY-CM20B, HY-CM20W]
Ceiling mounting holes
(2 places)
Ceiling mounting holes
(3 places)
Note
Hardware used for mounting the ceiling mount bracket to
the ceiling is not supplied.
Step 4. Mount the speaker to the joint bracket.
Insert the speaker bracket into the joint bracket and
loosely secure the fixing bolt for temporary speaker
installation.
Step 5. Connect the speaker cable to the speaker input terminal.
For connections, refer to the instruction manual enclosed
with the speaker.
15°
45°
Step 2. Attach a joint bracket to the ceiling mount bracket using
the supplied 4 screws.
(30°)
• HY-CM10B, HY-CM10W
5.1. HY-CM10B and HY-CM10W
HY-CM10B
HY-CM10W
Dimensions
Weight
F-1000B, F-1000BT, F-1000W, F-1000WT,
F-1300B, F-1300BT
F-1300W, F-1300WT
Steel plate, black,
Steel plate, white,
paint
paint
48 (w) x 100 (h) x 108 (d) mm
210 g
Accessories
Machine screw M5 x 10 with washers …4
Finish
Speaker bracket
(supplied with the speaker)
• HY-CM20B, HY-CM20W
Applicable Speaker
HY-CM20B
Speaker bracket
(supplied with the speaker)
Dimensions
Weight
Accessories
Machine screw M5 x 10 with washers …4
Note
The design and specifications are subject to change without notice
for improvement.
[15° downward position]
1
Speaker system
F-2000 series
Screw M5 x 20
(supplied with the speaker)
30°
[45° downward position]
15°
30°
30°
45°
Note
The mating surfaces of the speaker bracket and joint
bracket are designed to interlock.
Ensure that both parts are securely engaged with each
other after mounting is complete.
Accessory screw M5 x 10
2
3
Mounting to the ceiling
HY-CM10B/W
4, 6
Joint bracket
(supplied with the speaker)
Fixing bolt
(supplied with the speaker)
Accessory screw M5 x 10
HY-CM20W
F-2000B, F-2000BT, F-2000W,F-2000WT,
Steel plate, black,
Steel plate, white,
paint
paint
84 (w) x 135 (h) x 175 (d) mm
610 g
Finish
Screw M5 x 20
(supplied with the speaker)
7.5°
Joint bracket
1
Speaker system
F-1000 series
5.2. HY-CM20B and HY-CM20W
Models No.
0°
(horizontal)
The figure above shows the
screw mounting positions
for the F-1300 series.
Adjustable within this angle range.
5. SPECIFICATIONS
Models No.
Applicable Speaker
Refer to the figures below for the positional relationship
between the speaker bracket's "groove" and the joint
bracket's "indentation."
[0° (horizontal) position]
[7.5° downward position]
Speaker bracket
4. FINISHED ASSEMBLING DIAGRAM
[HY-CM10B, HY-CM10W]
Note: Mount the bracket so that the speaker is suspended
in a horizontal orientation.
Step 6. Adjust the speaker's vertical mounting angle and tighten
the fixing bolt.
The speaker angle can be adjusted in 7.5º steps within the
range as follows.
• When the HY-10B/W is used
F-1000 series: 0º(horizontal) to 45º downward
F-1300 series: 7.5º to 45º downward
• When the HY-20B/W is used
F-2000 series: 15º to 45º downward
6.3
72.5
ø70
Indicates a potentially hazardous situation which, if
mishandled, could result in death or serious personal injury.
• Install the unit only in a location that can structurally support the
weight of the unit and the speaker. Doing otherwise may result in
the speaker falling down and causing personal injury and/or
property damage.
6.3
84
45
Step 1. Attach the speaker bracket to the rear of the speaker
cabinet. Use the screws supplied with the speaker.
(HY-CM10B/W: 2 pieces; HY-CM20B/W: 4 pieces)
[HY-CM10B, HY-CM10W]
175
20°
108
Unit: mm
[HY-CM20B, HY-CM20W]
40°
• Before installation or use, be sure to carefully read all the
instructions in this section for correct and safe operation.
• Be sure to follow all the precautionary instructions in this section,
which contain important warnings and/or cautions regarding
safety.
• After reading, keep this manual handy for future reference.
Tip: The wall bracket supplied with each speaker is not used.
48
1. SAFETY PRECAUTIONS
The HY-CM10B and HY-CM10W Ceiling Mount Brackets are used
to mount F-1000/1300 Series speakers to a ceiling in a horizontal
configuration.
The HY-CM20B and HY-CM20W Ceiling Mount Brackets are used
to mount F-2000 Series speakers in a horizontal configuration.
15°
CEILING MOUNT BRACKETS
HY-CM10B
HY-CM10W
HY-CM20B
HY-CM20W
6. INSTALLATION
30°
INSTALLATION MANUAL
2. GENERAL DESCRIPTION
2
3
Mounting to the ceiling
HY-CM20B/W
4, 6
Joint bracket
(supplied with the speaker)
Fixing bolt
(supplied with the speaker)
URL: http://www.toa.jp/
133-01-00122-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising