TOA HY-BH10B User manual
6. INSTALLATION
INSTALLATION MANUAL
BOARD HANGER BRACKET
HY-BH10B
Tip: The wall bracket supplied with each speaker is not used.
Step 1. Attach the speaker bracket to the rear of the speaker
cabinet. Use the screws supplied with the speaker.
Note: Attach the speaker bracket according to the
speaker mounting orientation.
Step 7. Adjust the speaker's vertical mounting angle and tighten
the fixing bolt.
The speaker angle can be adjusted in 7.5º steps within
the range as follows.
F-1000 series: 0º (horizontal) to 45º downward
F-1300 series: 0º (horizontal) to 37.5º downward
Step 2. Attach a joint bracket to the hanger bracket using the
supplied 4 screws.
1. SAFETY PRECAUTIONS
2. GENERAL DESCRIPTION
•
The HY-BH10B Board Hanger Bracket is used to mount an
F-1000/1300 Series speaker to a temporarily installed partition
board.
The speaker can be installed in either a vertical or horizontal
orientation.
•
•
Before
installation or use, be sure to carefully read all the
instructions in this section for correct and safe operation.
sureBe
to follow all the precautionary instructions in this section,
which contain important warnings and/or cautions regarding
safety.
reading,
After keep this manual handy for future reference.
WARNING
3. COMPONENT PARTS
•
the
Since
unit is designed for indoor use, do not install it
outdoors. If installed outdoors, the aging of parts causes the
speaker to fall off, resulting in personal injury.
•
notDo
use other methods than specified to mount the unit.
Extreme force is applied to the unit and the speaker could fall off,
possibly resulting in personal injuries.
•
•
Tighten
each bolt securely. Ensure that the unit has no loose
joints after installation to prevent accidents that could result in
personal injury.
Mounting hole (A)
Machine screws
M5 x 10 with washers x 4
4. FINISHED ASSEMBLING DIAGRAM
[Vertical installation]
6 – 38 mm
not Do
mount the unit in locations exposed to constant vibration.
The unit can be damaged by excessive vibration, potentially
causing the speaker to fall, which could result in personal injury.
•
not Do
use anti-rust lubricant. If it contacts resin or rubber parts,
they could deteriorate and cause the unit to fall, possibly
resulting in personal injury.
CAUTION
Indicates a potentially hazardous situation which, if
mishandled, could result in moderate or minor personal
injury, and/or property damage.
•
touching
Avoid the unit's sharp metal edge to prevent injury.
•
not Do
hang down from the unit as this may cause it to fall down
or drop, resulting in personal injury and/or property damage.
[F-1000 series]
45°
0°
(horizontal)
28 – 60 mm
Step 5. Mount the speaker to the partition board.
Slide the sliding bracket to pinch the partition board
between the sliding bracket and hanger bracket, then
tighten the knob bolt.
Step 6. Connect the speaker cable to the speaker input terminal.
For connections, refer to the instruction manual enclosed
with the speaker.
[Horizontal installation]
theUse
specified speaker in combination. Doing otherwise may
cause the speaker to fall off, resulting in personal injury.
•
Refer to the figures below for the positional relationship
between the speaker bracket's "groove" and the joint
bracket's "indentation."
[F-1300 series]
Hanger bracket x 1
Sliding bracket x 1
Joint bracket
0°
(horizontal)
Mounting hole (B)
Plain washer for knob bolt x 1
the
Install
unit only in a location that can structurally support the
weight of the unit and the speaker. Doing otherwise may result in
the speaker falling down and causing personal injury and/or
property damage.
•
Step 4. Attach the sliding bracket to the hanger bracket using the
knob bolt and plain washer. Select either mounting hole A
or B in the sliding bracket, depending on the thickness of
the partition board.
[Mountable partition board thickness]
Knob bolt x 1
Indicates a potentially hazardous situation which, if
mishandled, could result in death or serious personal injury.
Step 3. Mount the speaker to the joint bracket.
Insert the speaker bracket into the joint bracket and
loosely secure the fixing bolt for temporary speaker
installation.
Speaker bracket
The figure at left shows the
screw mounting positions
for the F-1300 series.
37.5°
30°
30°
Note
The mating surfaces of the speaker bracket and joint
bracket are designed to interlock.
Ensure that both parts are securely engaged with each
other after mounting is complete.
When protection against falls is required:
Fix the sliding bracket directly to the
partition board using screws.
Note that the fixing screws are not
supplied.
Partition board
Screw M5 x 20 (supplied with the speaker)
1
5. SPECIFICATIONS
Applicable Speaker
F-1000B, F-1000BT, F-1000W, F-1000WT,
F-1300B, F-1300BT, F-1300W, F-1300WT
Finish
Dimensions
Steel plate, black, paint
48 (w) x 100 (h) x 108 (d) mm
(knob bolt excluded)
Weight
Speaker system
F-1000 series
Speaker bracket
(supplied with the speaker)
Note
The design and specifications are subject to change without notice
for improvement.
Accessory screw M5 x 10
3
Fixing bolt
(supplied with the speaker)
Plain washer for kob bolt
2
Hanger bracket
4
3, 7
300 g
Knob bolt
Sliding bracket
Joint bracket
(supplied with the speaker)
Mounting hole B
Mounting hole A
URL: http://www.toa.jp/
133-01-00120-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising