TOA | N-8050DS | manual | TOA N-8050DS User manual

TOA N-8050DS User manual
3. INSTALLATION PRECAUTIONS
INSTALLATION
MANUAL
DOOR STATION
N-8050DS
1. GENERAL DESCRIPTION
Designed to connect to the IP Intercom Exchange, the N8050DS is a door station featuring high quality hands-free
conversation and has a contact output (momentarily closed)
to remotely control an electronic door lock.
Using with an electrical box or surface mounting box, the
station can be mounted to a wall.
The N-8050DS is in full conformity with IP54 water-proof
and dust-proof standards. The operating temperature range
is –10 to +50°C.
As provided with guard nets inside to cover over the
openings of microphone and speaker, the N-8050DS can be
installed free from care in public space.
• When installing the N-8050DS
outdoors or at locations where it gets
wet with water, tightly seal the panel
edges. Besides, provide a weep hole
at the underside of the mounting box
to permit water to drain off.
• When installing the N-8050DS under
difficult environmental conditions
such as in coastal areas or at humid
locations, cover the inside of the N8050DS with coating. For the coating
method, consult TOA sales office.
Seal the panel edges.
N-8050DS's
front panel
4. WIRING
4.1. Connection to the Exchange
Connect the Exchange to the station's LINE terminals via
the E-7000TB Terminal Board as illustrated.
N-8000EX/8010EX Exchange
16 lines
2. WALL MOUNTING
2.1. Mounting to a 3-gang Switch Box (with cover)
Mount the N-8050DS to electrical
boxes mounted in the wall.
Mini-clamp connector
(Supplied with the
N-8000EX/8010EX)
Wall surface
E-7000TB
Terminal board
Acoustic material (accessory)
Note
Lay it down along the inside
of the box.
Both upper and lower
terminals (clip terminals)
are internally connected.
N-8050DS
YC-150 Back box (option)
or 3-gang electrical box
Twisted pair cable
Wall
LINE H C
Oval head combination screw
M4 x 25 (accessory)
N-8050DS
N-8050DS (rear panel)
[Section view]
Notes
• The wall should be over 12 mm thick, and the opening in
the wall for an electrical box should be under 115 mm
(wide) by 162 mm (high).
• When using for electronic door lock control, fix the N8050DS with tamper-proof screws such as "Torx" screws
to prevent it from being easily removed.
• Be sure to ground the electrical box.
4.2. Connection to an External Relay
N-8000EX/8010EX Exchange
-
Accessory screws
The N-8050DS comes with 2 types of screws: oval head
combination screw M4 x 25 and oval head combination
screw UNC No.6 x 18. For the electrical box provided with
unified threads, use the oval head combination screws UNC
No.6 x 18.
Relay
+
+24 V DC
GND
LINE H C
Open collector output: 30 V DC, 50 mA
2.2. Mounting to the YS-13A Wall Mount Box
Install the YS-13A on a wall and mount the station in the
same way as 2.1.
External
power supply
Diode
N-8050DS (Rear panel)
4.3. Type of Cable
Step 2. Loosen the terminal screws and insert the cables.
The types of cables are to be determined according to the
following conditions.
Step 3. Tighten the terminal screws securely.
• Twisted pair wires (such as those used for electronic
push-button telephone) are to be used for wiring between
the Exchange and the stations in principle.
• The number of cables pairs laid should be determined
considering the possibility of future expansion of the
system.
• Outdoor wires should be used where wiring passes
through inaccessible areas such as ceilings or under floors
where the maintenance is not performed. Indoor wires
may also be used, however, in case where there is no risk
of deterioration due to exposure to heat, etc.
Notes
• Tug lightly on the cable to be sure that it does not
pull free. If the cable pulls free, loosen the
terminal screw again and reconnect from Step 2.
• To avoid stripping the screws, use the
screwdriver appropriate to the screws tightened
into the terminal plug.
Tighten
Note
Specifications related to each junction are as follows.
Terminal screw
Mini-clamp connector (N-8000EX/8010EX line terminal)
Conductor diameter: ø0.4 – 0.65 mm (AWG22 – 26),
solid wire
Outside diameter:
ø1.05 mm or below
Clip terminal (E-7000TB)
Conductor diameter: ø0.4 – 0.8 mm (AWG20 – 26),
solid wire
Outside diameter:
ø1.5 mm or below
Terminal station (LINE, H, C terminals)
Conductor diameter: ø0.4 – 1.3 mm (AWG16 – 26),
solid wire, stranded wire
4.4. Relations Between Core Diameter of Cable
and Maximum Cable Length
Cable
4.6. Mini-clamp Connector Connection
Connect the mini-clamp connector supplied with the N8000EX/8010EX to a cable using a commercially available
tool (pliers).
Step 1. Cut off two-cable ends in equal length, and insert
them securely to a cover section (transparent side)
of the mini-clamp connector.
Note
Insert the cable without
stripping the cable jacket.
Referring to the following chart as guidelines, design the
distance between the Exchange and stations so that loop
resistance becomes 170 Ω or less.
Conductor
Loop
Maximum cable length
diameter resistance between the Exchange and station.
(mm)
(Ω/ km) (Assuming that the loop resistance is 170 Ω.)
ø0.4
295
570 m
ø0.5
187
900 m
ø0.65
113
1.5 km
ø0.9
58
2.9 km
4.5. Terminal Station Connection
Step 1. Strip a cable jacket of approx 7 mm to expose
inner cable.
For cables, refer to Type of Cable.
Cover
(transparent side)
Cable
Step 2. With a pair of pliers, lightly
pinch the mini-clamp cover
and, after ensuring that the
cable is securely inserted,
firmly squeeze on the cover.
Note
Squeeze on the mini-clamp cover until it is
correctly locked.
Step 3. Insert the wired connector (plug) into the
exchange's connector (socket) until it locks into
place.
7 mm
N-8000EX/8010EX Rear panel
Note
Do not solder plate on exposed inner cables when
using a stranded wire.
URL: http://www.toa.jp/
133-06-00031-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising