TOA | N-8650DS | manual | TOA N-8650DS User manual

TOA N-8650DS User manual
INSTALLATION
MANUAL
IP DOOR STATION N-8650DS
Step 3. Attach the N-8650DS to the panel mount frame.
Hook the tabs on the N-8650DS's upper side into
the panel mount frame's slots, fit them into place,
then secure the both bottom sides with a screw.
Panel mount frame
Tab
1. SAFETY PRECAUTIONS
• Before installation or use, be sure to carefully read all the
instructions in this section for correct and safe operation.
• Be sure to follow all the precautionary instructions in this
section, which contain important warnings and/or cautions
regarding safety.
• After reading, keep this manual handy for future reference.
Screw
Screw hole
Bottom view
N-8650DS
CAUTION
Indicates a potentially hazardous situation which, if
mishandled, could result in moderate or minor personal
injury, and/or property damage.
3.2. On-Wall Mounting
Attach the N-8650DS to the YS-13A Wall-mount box
installed on a wall.
• Use the dedicated AC adapter or its equivalent for the unit.
Note that the use of other adapter may cause a fire.
Step 1. Loosen the screw on the N-8650DS's bottom, then
detach the panel mount frame.
(Refer to Step 1 in the previous section.)
2. GENERAL DESCRIPTION
Step 2. Mount the panel mount frame to the back box.
Designed to connect to the IP network, the N-8650DS is an
indoor use door station featuring high quality hands-free
conversation. It is equipped with 1 contact input and 5
contact outputs, allowing connections to a sensor, electronic
lock, and other external equipment. The N-8650DS can be
mounted either flush in a wall or on a wall by using the
designated mounting box.
Wall surface
Panel mount frame
3. WALL MOUNTING
Rear plate
3.1. In-Wall Mounting
Install the YC-13A
with its bottom
plate removed.
Mount the panel mount frame to the YC-150 Back box or 3gang electrical box installed in a wall, then attach the N8650DS to the panel mount frame.
Screw
Step 1. Loosen the screw on the N8650DS's bottom, then detach
the panel mount frame.
Step 2. Mount the panel mount
frame to the YC-150 or
electrical box.
YS-13A
Machine screw M4 x 20 (accessory)
Accessory screws
N-8650DS's bottom
Wall surface
The N-8650DS comes with 2 types of screws: machine
screw M4 x 20 and UNC No.6-32 x 20.
Use the M4 x 20 screw.
Step 3. Attach the N-8650DS to the panel mount frame.
Hook the tabs on the N-8650DS's upper side into
the panel mount frame's slots, fit them into place,
then secure the both bottom sides with a screw.
(Refer to Step 2 in the previous section.)
Panel mount frame
N-8650DS
[YS-13A dimensional drawing]
6-φ4.5 (for wall mounting)
4-M4 (for N-8650DS mounting)
Machine screw M4 x 20 (accessory)
Accessory screws
The N-8650DS comes with 2 types of screws: machine
screw M4 x 20 and UNC No.6-32 x 20.
For the electrical box provided with unified threads, use the
oval head combination screws UNC No.6-32 x 20.
163.5
92
46
YC-150 Back box
YC-150 Back box
or 3-gang electrical box or 3-gang electrical box
83.5
116.5
55
Unit: mm
4. WIRING
N-8650DS rear
3 Connection to an external equipment
Contact output 1 (brown)
Contact output 2 (red)
Contact output 3 (orange)
To an indicator or other
external equipment
[Specifications]
Open collector output
Withstand voltage: 30 V DC
Max. control current: 50 mA
Contact output 4 (yellow)
Contact output COM (purple)
Contact output (blue)
Contact output (blue)
3
1
To an electronic lock or
other external equipment*
[Specifications]
Relay contact output
Withstand voltage: 30 V DC
Max. control current: 500 mA
Contact input HOT (gray)
To a switch, sensor, or
other external equipment
[Specifications]
No-voltage closed contact
input.
Open voltage: 5 V DC
Short-circuit current: 10 mA
or less
Contact input COM (white)
2
Speaker cable (black)
LAN coupler (accessory)
To external speakers
(8 Ω, 0.6 W or more)
* Connection example (When using a 24 V DC relay)
External power supply
Diode
Speaker cable (black)
Relay
Contact output (blue)
Contact output (blue)
1 Network connection
Can be connected to a network
of 10BASE-T/100BASE-TX in
auto-negotiation.
Use a UTP category 5 or more
straight through cable with an
RJ-45 connector for this
connection.
• Power supply connection (
2 AC adapter connection
Connect the AC adapter.
Use the AD-1210P/1215P (option) or
equivalent.
As for the usable adapter, consult
your TOA dealer.
-
+
24 V DC
GND
Note: Treat unused cables so as not to
short-circuit.
1 or 2 )
The following 2 methods are available for supplying power to the station.
• From a DC 12 V AC adapter
• From an IEEE802.3af compliant PoE switching hub
(For connection, refer to the instruction manual supplied with the switching hub.)
5. ACCESSORIES
UNC No.6-32 x 20 ........................................................... 4
Machine screw M4 x 20 ................................................... 4
LAN coupler ..................................................................... 1
Warning
This is a class A product. In a domestic environment this product may cause radio interference in which case the
user may be required to take adequate measures.
Traceability Information for Europe (EMC directive 2004/108/EC)
Manufacturer:
Authorized representative:
TOA Corporation
TOA Electronics Europe GmbH
7-2-1, Minatojima-Nakamachi, Chuo-ku, Kobe, Hyogo, Japan
Suederstrasse 282, 20537 Hamburg, Germany
URL: http://www.toa.jp/
133-06-00035-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising