TOA | PE-154BS | manual | TOA PE-154BS User manual

TOA PE-154BS User manual
INSTRUCTION MANUAL
PENDANT SPEAKER
PE-154BS
Thank you for purchasing TOA's Pendant Speaker.
Please carefully follow the instructions in this manual to ensure long, trouble-free use
of your equipment.
TABLE OF CONTENTS
1. SAFETY PRECAUTIONS ........................... 1
5. DIMENSIONAL DIAGRAM ......................... 4
2. GENERAL DESCRIPTION
6. WIRING DIAGRAM ...................................... 4
AND FEATURES ......................................... 2
7. FREQUENCY RESPONSE (1 W, 4 m) ....... 5
3. IMPEDANCE CHANGE .............................. 2
8. SPECIFICATIONS ...................................... 5
4. INSTALLATION .......................................... 3
1. SAFETY PRECAUTIONS
• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe
operation.
• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or
cautions regarding safety.
• After reading, keep this manual handy for future reference.
injury and/or property damage.
WARNING
Indicates a potentially hazardous situation which,
if mishandled, could result in death or serious
personal injury.
When Installing the Unit
• Refer all installation work to the dealer from whom
the speaker was purchased. Installation work
requires extensive technical knowledge and
experience. The speaker may fall off if incorrectly
installed, resulting in possible personal injury.
• Install the speaker only in a location that can
structurally support the full weight of the unit and
mounting bracket. Doing otherwise may result in
the speaker falling down and causing personal
• Since the unit is designed for in-door use, do not
install it outdoors. If installed outdoors, the aging of
parts causes the unit to fall off, resulting in personal
injury. Also, when it gets wet with rain, there is a
danger of electric shock.
• Do not use other methods than specified to install
the speaker. Extreme force is applied to the
speaker and the speaker could fall off, possibly
resulting in personal injuries.
• Use screws that are appropriate for the ceiling's
material and structure. Failure to do so may cause
the speaker to fall, resulting in material damage
and possible personal injury.
• Ensure that all screws are securely tightened. If
they are loose after installation, the speaker could
fall down, possibly resulting in personal injury.
Traceability Information for Europe
Manufacturer:
TOA Corporation
7-2-1, Minatojima-Nakamachi, Chuo-ku, Kobe, Hyogo,
Japan
Authorized representative:
TOA Electronics Europe GmbH
Suederstrasse 282, 20537 Hamburg,
Germany
• Do not mount the speaker in locations exposed to
constant vibration. The speaker or its mounts can
be damaged by excessive vibration, potentially
causing the speaker to fall, which could result in
personal injury.
• Do not use anti-rust lubricant. If it contacts resin or
rubber parts, they could deteriorate and cause the
speaker to fall, possibly resulting in personal injury.
• Do not install the speaker in indoor swimming pools
or such locations where liquid chemicals are used.
The parts deteriorate if corroded, causing the
speaker to fall, which could result in personal
injury.
CAUTION
Indicates a potentially hazardous situation which,
if mishandled, could result in moderate or minor
personal injury, and/or property damage.
When Installing the Unit
• Avoid touching the speaker's sharp metal edge to
prevent injury.
• To avoid electric shocks, be sure to switch off the
amplifier's power when connecting speakers.
When the Unit is in Use
When the Unit is in Use
• If any of the following irregularities occurs,
immediately switch off the amplifier's power, and
inform the shop from where the speaker was
purchased. Further using the speaker may result in
fire or electric shock.
· If you detect smoke or a strange smell coming
from the speaker
· If water or any metallic object gets into the
speaker
· If the speaker falls, or the speaker case breaks
• Do not operate the speaker for an extended period
of time with the sound distorting. Doing so may
cause the speaker to heat, resulting in a fire.
• To prevent a fire or electric shock, never open nor
remove the speaker case. Refer all servicing to
your nearest TOA dealer.
• Do not stand or sit on, nor hang down from the
speaker as this may cause it to fall down or drop,
resulting in personal injury and/or property
damage.
• Have the speaker checked periodically by the shop
from where it was purchased. Failure to do so may
result in corrosion or damage to the speaker or the
mounts that could cause it to fall, possibly causing
personal injury.
2. GENERAL DESCRIPTION AND FEATURES
The PE-154BS is certified according to the European Standard EN 54-24: 2008, the International Standard
ISO 7240-24: 2010 and compliant with the British Standard BS 5839-8: 2008 14.8.
The PE-154BS is a pendant speaker designed for ceiling suspension installations. Considered in architectural
design, it can blend in with lighting equipment.
A directly-attached 3 m (9.84 ft) speaker cord allows the speaker to be suspended from the high ceiling.
The speaker is driven on high-impedance (100 V and 70 V) line, and its input power (impedance) can be
easily switched.
Note
Never dismantle the PE-154BS in any way even for repainting reason. Since the PE-154BS is certified in the
form of complete assembly by the above-mentioned standards, it does not meet these standards if
dismantled.
3. IMPEDANCE CHANGE
The input power (impedance) is factory-preset to 15 W (670 Ω) for 100
V line and 7.5 W (670 Ω) for 70 V line.
When changing this setting, use a standard screwdriver to rotate the
rotary switch on the upper side of the speaker to the desired position.
Impedance
100 V line
70 V line
670 Ω
15 W
7.5 W
1 kΩ
10 W
5W
2 kΩ
5W
2.5 W
Bold figures represent factory-preset values.
Notes
• Switch off the amplifier's power when changing the input power.
• No sound is output when the switch is set to the OFF position.
2
Speaker
4. INSTALLATION
Step 1. Secure the ceiling bracket to the ceiling with
4 screws.
Pull the cable through the cable gland in the
bracket.
Step 5. Put the mounting hanger onto the ceiling
bracket's hook.
Ceiling bracket (accessory)
Cable gland
Ceiling
Tapping screw 4 x 16 (accessory)
Note
If these screws are not appropriate
for the ceiling material, separately
prepare the proper screws.
Mounting hanger
(accessory)
Ceiling bracket (accessory)
Cable (from the amplifier)
Note: Make a clearance hole for the cable gland in
the ceiling panel as needed so that the ceiling
bracket can be attached firmly to the ceiling.
Step 6. Connect the cable (from the amplifier) to the
screw terminal.
[Cable gland hole dimensions (Reference)]
36 (1.42)
1.2
4-unthreaded hole
Screw terminal
2)
12
(0.47)
1(
36 (1.42)
ø3
6
Unit: mm (in)
Step 2. Pass the speaker cable through the supplied
ceiling cover, and cut the cable to the
desired length.
55 mm
(2.17")
3
2
Cable (from the
amplifier)
COM
HOT
Note
Connect 2 cables.
Cover-retaining
nut
Mounting hanger
(accessory)
Loosens
Cover-retaining nut
Tightens
Step 3. Run the speaker cable through the cable
holes in the mounting hanger.
Step 4. Connect the speaker cable to the screw
terminal.
Mounting hanger
(accessory)
Ceiling cover
Speaker cable
3 m (9.84 ft)
Ceiling cover
(accessory)
8 mm
(0.31")
Loosens
7
HOT (Blue)
COM (Gray)
Speaker cable
Screw terminal
Tightens
Step 7. Push the ceiling cover, slipped over the
connected cables, onto the ceiling surface,
then tighten the cover-retaining nut using a
17 mm (0.67") hex wrench.
In the case of exposed wiring, cut out the
cable entry tab on the rim of the cover, then
make connections.
Cut out this thin tab.
(another tab is on the
opposite side.)
Ceiling cover
(Earth)
HOT (Brown)
COM (Black)
Screw terminal
3
[When making a bridge connection]
Ceiling bracket
Punch out the knockout in the ceiling bracket and attach
the cable gland (option) there.
Notes
• To punch out the knockout, apply a force to it in the
direction of the arrow as shown at right. In this case,
take care not to bend the metal rim along the knockout.
• Run the cable (to the next speaker) through the cable
gland, then connect the cable to each terminal according
to the polarity indication at the screw terminal.
• Make 2 clearance holes for the cable glands in
the ceiling panel as needed so that the ceiling Cable (from
bracket can be attached firmly to the ceiling.
the amplifier)
[Cable gland hole dimensions (Reference)]
Cable gland (option)
Cable (to the next speaker)
Screw terminal
COM
HOT
2)
36 (1.42)
1.2
Note: Connect 2 cables.
16
(0.63)
12
(0.47)
1(
Cable gland
4-unthreaded hole
36 (1.42)
ø3
Knockout
15 (0.59)
Unit: mm (in)
5. DIMENSIONAL DIAGRAM
Unit: mm (in)
[Front]
[Top]
ø120 (ø4.72)
65 (2.56)
42.4
(1.67)
(4.57)
Cable gland
PG13.5-12
knockout
4-ø4.5 (ø0.18)
97 (3.82)
50.9 (2)
ø20.3 (ø0.8)
4-6.6 x 3.6 (0.26 x 0.14)
25.45
(1.0)
9.3 (0.37)
4.2
(0.17)
42.4
(1.67)
(9.84 ft)
Max. 3000
116
50.9 (2)
12
(0.47)
33.9
(1.33)
251 (9.88)
7.7 (0.3)
[Bottom]
ø186 (ø7.32)
6. WIRING DIAGRAM
Thermal fuse
Terminal block (84°C or 183.2°F) Rotary switch
COM
HOT
EARTH (
)
OFF
OFF
OFF
Matching
transformer
Network
circuit
2 kΩ
1 kΩ
8Ω
SP1
670 Ω
COM
HOT
EARTH (
4
)
0
COM
(Factory-preset wiring)
SP2
7. FREQUENCY RESPONSE (1 W, 4 m)
[dB]
90
80
70
60
50
20
50
100
500
1k
Frequency-SPL
5k
10 k
20 k [Hz]
8. SPECIFICATIONS
Standards
Environment Type
Rated Noise Power
Rated Impedance
Sensitivity
Max. SPL
Frequency Response
Coverage Angle (–6 dB)
Speaker Component
Operating Temperature
Cable Gland
Cable Connection
Speaker Cable
Applicable Cable Size
Finish
Dimensions
Weight
Accessories
Certified to the European Standard EN 54-24: 2008
EN 54-24: 2008
Loudspeaker for voice alarm systems
11
0359-CPD-0105
for fire detection and fire alarm systems
0359
Certification No. 0359-CPD-0105
Certified to the International Standard ISO 7240-24: 2010
Sound system loudspeakers for fire detection and fire alarm systems
In Compliance with the British Standard BS5839-8: 2008 14.8
Type A (Indoor applications)
15 W (100 V line), 7.5 W (70 V line)
100 V line: 670 Ω (15 W), 1 kΩ (10 W), 2 kΩ (5 W)
70 V line: 670 Ω (7.5 W), 1 kΩ (5 W), 2 kΩ (2.5 W)
91 dB (1 W, 1 m at 500 Hz to 5 kHz pink noise)
87 dB (1 W, 1 m at 100 Hz to 10 kHz pink noise)
75 dB (1 W, 4 m at 100 Hz to 10 kHz pink noise)
99 dB (15 W, 1 m at 100 Hz to 10 kHz pink noise)
87 dB (15 W, 4 m at 100 Hz to 10 kHz pink noise)
70 Hz – 20 kHz
Horizontal and Vertical: 360° (500 Hz), 170° (1 kHz), 90° (2 kHz), 70° (4 kHz)
Low frequency: 12 cm (5") cone-type
High frequency: 2.5 cm (1") balanced dome tweeter
–10 ºC to +50 ºC (14 ºF to 122 ºF)
Size: PG 13.5
One cable gland is factory-installed.
For bridge connection, one cable gland can be added.*
Screw terminal (Steatite) x 2
4-core fireproof cable, 3 m (9.84 ft)
Outer diameter: ø6.5 – ø12.5 mm
Conductor:
Solid wire or 7-core wire
0.8 – 7 mm2 (AWG 18 – 9) for solid wire,
0.8 – 4 mm2 (AWG 18 – 11) for 7-core wire
Enclosure: HIPS resin, off-white (RAL 9010 or equivalent color)
Grille:
Surface-treated steel plate net, off-white (RAL 9010 or equivalent color),
paint
ø186 x 251 (h) mm (ø7.32" x 9.88") (speaker only)
2.33 kg (5.14 lb) (speaker only)
Ceiling bracket ... 1, Mounting hanger ... 1, Ceiling cover ... 1,
Tapping screw 4 x 16 ... 4
Notes
• The design and specifications are subject to change without notice for improvement.
• The Specifications data was measured in an anechoic chamber, according to EN 54-24.
• Reference axis: Axis is on the center of grille surface and perpendicular to the grille surface.
• Reference plane: Plane is on the grille surface and perpendicular to the reference axis.
• Horizontal plane: Plane is containing the reference axis and perpendicular to the reference plane.
* Suppliable cable gland's part code and name: 525-52-011-70 Cable gland AVC PGB13.5-12 (GRY)
5
URL: http://www.toa.jp/
533-06-238-2A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising