TOA | PJ-100W | manual | TOA PJ-100W User manual

TOA PJ-100W User manual
INSTRUCTION MANUAL
PROJECTION SPEAKERS
PJ-100W, PJ-200W
Thank you for purchasing TOA's Projection Speakers.
Please carefully follow the instructions in this manual in order to ensure long, trouble-free use of your equipment.
1. SAFETY PRECAUTIONS
4. IMPEDANCE CHANGE
• Before installation or use, be sure to carefully read all the
instructions in this section for correct and safe operation.
• Be sure to follow all the precautionary instructions in this
section, which contain important warnings and/or
cautions regarding safety.
• After reading, keep this manual handy for future
reference.
When changing impedance, follow the procedure below
after unscrewing and removing the cover.
Cabinet
Grommet B
Cover
WARNING
Indicates a potentially hazardous situation which,
if mishandled, could result in death or serious
personal injury.
• Install the speaker only in a location that can structurally
support the weight of the speaker and the mounting
bracket. Doing otherwise may result in the speaker falling
down and causing personal injury and/or property damage.
• Do not stand or sit on, nor hang down from the speaker
as this may cause it to drop, resulting in personal injury
and/or property damage.
Screws
Bracket
Speaker cable
Grommet A
Detach the black input cable (HOT) and connect it to the
terminal of the desired input impedance/wattage according
to the tables below.
Cable clump A
Speaker cable
CAUTION
Indicates a potentially hazardous situation which,
if mishandled, could result in moderate or minor
personal injury, and/or property damage.
• Do not operate the speaker for an extended period of
time with the sound distorting. This is an indication of a
malfunction, which in turn can cause heat to generate
and result in a fire.
2. GENERAL DESCRIPTION
The PJ-100W and PJ-200W Projection Speakers are
designed for indoor use. The built-in terminal board
provides an easy cable connection and allows bridge
wiring. Its wide frequency range makes it suitable for use
in both paging and BGM applications.
COM
Grommet A
Black input cable (HOT)
Terminal board
[Back side view of cover removed]
[PJ-100W]
Imp.
250 Ω
500 Ω
1 kΩ
2 kΩ
4 kΩ
• Maximum input: 15 W (PJ-100W), 30 W (PJ-200W).
• Built-in transformer for 50 V, 70 V and 100 V speaker
line.
• Two grommets for parallel (bridge) connection.
Factory-preset
values
[PJ-200W]
Imp.
3. FEATURES
Line Voltage
50 V
70 V 100 V
10 W
–
–
5W
10 W
–
2.5 W
5W
10 W
1.25 W 2.5 W
5W
0.63 W 1.25 W 2.5 W
125 Ω
250 Ω
500 Ω
1 kΩ
2 kΩ
Line Voltage
50 V
70 V 100 V
20 W
–
–
10 W
20 W
–
5W
10 W
20 W
2.5 W
5W
10 W
1.25 W 2.5 W
5W
Factory-preset
values
Note: The black input cable has been connected to the
terminal of 1 kΩ impedance for the PJ-100W and
500 Ω for the PJ-200W.
5. BRIDGE CONNECTION
7. WIRING DIAGRAMS
Route the speaker cable through grommet B and clump it
with a cable clump B as illustrated below.
[PJ-100W]
Cable for parallel connection
(not supplied)
4 kΩ
8Ω
2 kΩ
1 kΩ
Speaker cable
Cable clump A
Cable clump B
500 Ω
100 V Line
70 V Line
Black
50 V Line
250 Ω
(COM)
0
COM
White
(Factory-preset values)
Grommet A
Grommet B
[PJ-200W]
(HOT)
2 kΩ
Factory preset
Terminal board
8Ω
1 kΩ
500 Ω
[Back side view of cover removed]
250 Ω
100 V Line
70 V Line
Black
50 V Line
125 Ω
6. SPEAKER MOUNTING DIMENSIONS
51 (2.01) 51 (2.01)
11 x 20 (0.43 x 0.79)
0
COM
Unit: mm (in)
White
(Factory-preset values)
2-ø11 (2-ø0.43)
8. SPECIFICATIONS
[PJ-100W]
Rated Input
Input Impedance
Preset Impedance
Sound Pressure Level
Speaker Diameter
Frequency Range
Finish
Dimensions
Weight
10 W (50 V, 70 V, 100 V Line)
100 V Line : 1 kΩ (10 W), 2 kΩ (5 W), 4 kΩ (2.5 W)
70 V Line : 500 Ω (10 W), 1 kΩ (5 W), 2 kΩ (2.5 W), 4 kΩ (1.25 W)
50 V Line : 250 Ω (10 W), 500 Ω (5 W), 1 kΩ (2.5 W), 2 kΩ (1.25 W), 4 kΩ (0.63 W)
1 kΩ
92 dB (1 m, 1 W) at 1 kHz
12 cm (5")
65 Hz – 15 kHz
Cabinet, Cover : ABS resin, off-white
Bracket :
SPCC, off-white
160 (w) x 200 (h) x 195 (d) mm (6.3" x 7.87" x 7.68")
1.8 kg (3.97 lb)
[PJ-200W]
Rated Input
Input Impedance
Preset Impedance
Sound Pressure Level
Speaker Diameter
Frequency Range
Finish
Dimensions
Weight
20 W (50 V, 70 V, 100 V Line)
100 V Line : 500 Ω (20 W), 1 kΩ (10 W), 2 kΩ (5 W)
70 V Line : 250 Ω (20 W), 500 Ω (10 W), 1 kΩ (5 W), 2 kΩ (2.5 W)
50 V Line : 125 Ω (20 W), 250 Ω (10 W), 500 Ω (5 W), 1 kΩ (2.5 W), 2 kΩ (1.25 W)
500 Ω
95 dB (1 m, 1 W) at 1 kHz
16 cm (6.5")
50 Hz – 20 kHz
Cabinet, Cover : ABS resin, off-white
Bracket :
SPCC, off-white
200 (w) x 255 (h) x 250 (d) mm (7.87" x 10.04" x 9.84")
2.5 kg (5.51 lb)
Note: The design and specifications are subject to change without notice for improvement.
Traceability Information for Europe (EMC directive 2004/108/EC)
Manufacturer:
Authorized representative:
TOA Corporation
TOA Electronics Europe GmbH
7-2-1, Minatojima Nakamachi, Chuo-ku, Kobe, Hyogo, Japan
Suederstrasse 282, 20537 Hamburg,Germany
URL: http://www.toa.jp/
533-06-004-9A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising