TOA | SR-F08 | manual | TOA SR-F08 User manual

日本語の取扱説明書は裏側をご覧ください。
INSTRUCTION MANUAL
2WAY PASSIVE SPEAKER SYSTEM SR-F08
TABLE OF CONTENTS
1. SAFETY PRECAUTIONS .............................. 2
2. GENERAL DESCRIPTION . .......................... 3
3. FEATURES .................................................... 3
4. INPUT CONNECTORS . ................................ 4
5. EQUALIZATION
USING A DIGITAL SIGNAL PROCESSOR . 5
7. SAFETY WIRE INSTALLATION ................... 5
8. SELECTING
THE OPTIONAL MOUNTING BRACKET . .. 6
9. DIMENSIONAL DIAGRAM ........................... 8
10. SPECIFICATION . ........................................ 8
6. CHANGING
THE HORN COVERAGE ANGLE ................ 5
Thank you for purchasing TOA’s 2way Passive Speaker System.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
133-01-00261-00
1. SAFETY PRECAUTIONS
• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe
operation.
• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or
cautions regarding safety.
• After reading, keep this manual handy for future reference.
Safety Symbol and Message Conventions
Safety symbols and messages described below are used in this manual to prevent bodily injury and property
damage which could result from mishandling. Before operating your product, read this manual first and
understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.
WARNING
CAUTION
Indicates a potentially hazardous situation which, if mishandled, could
result in death or serious personal injury.
Indicates a potentially hazardous situation which, if mishandled, could
result in moderate or minor personal injury, and/or property damage.
WARNING
• Avoid installing or mounting the speaker in unstable
locations, such as on a rickety table or a slanted
surface. Doing so may result in the speaker falling
down and causing personal injury and/or property
damage.
• Install the speaker only in a location that can
structurally support the weight of the speaker and
the mounting bracket. Doing otherwise may result
in the speaker falling down and causing personal
injury and/or property damage.
• Since the speaker is designed for indoor use, do not
install it outdoors. If installed outdoors, the aging
of parts causes the speaker to fall off, resulting in
personal injury. Also, when it gets wet with rain,
there is a danger of electric shock.
• Do not use other methods than specified to mount
the bracket. Extreme force is applied to the speaker
and the speaker could fall off, possibly resulting in
personal injuries.
• Attach the safety wire to the speaker. If not attached,
the speaker could fall off, resulting in personal injury
(only when installing the speaker to the ceiling, wall,
or pipe.)
• Use nuts and bolts that are appropriate for the
ceiling’s or wall’s structure and composition. Failure
to do so may cause the speaker to fall, resulting in
material damage and possible personal injury.
• Tighten each nut and bolt securely. Ensure that
the bracket has no loose joints after installation
to prevent accidents that could result in personal
injury.
2
• Use the specified mounting bracket and speaker
stand in combination. Doing otherwise may cause the
speaker or component to fall off, resulting in personal
injury.
• Do not mount the speaker in locations exposed to
constant vibration. The mounting bracket can be
damaged by excessive vibration, potentially causing
the speaker to fall, which could result in personal injury.
• Avoid installing the speaker in indoor swimming
facilities that are not well ventilated. In such a location,
the bracket may be vulnerable to corrosion, eventually
allowing the speaker to fall resulting in personal injury.
CAUTION
• Avoid touching the speaker’s sharp metal edge to
prevent injury.
• Do not place heavy objects on the speaker as this
may cause it to fall or break which may result in
personal injury and/or property damage. In addition,
the object itself may fall off and cause injury and/or
damage.
• Do not operate the speaker for an extended period of
time with the sound distorting. Doing so may cause
the connected speakers to heat, resulting in a fire.
• Do not stand or sit on, nor hang down from the
speaker as this may cause it to fall down or drop,
resulting in personal injury and/or property damage.
• Have the speaker checked periodically by the shop
from where it was purchased. Failure to do so may
result in corrosion or damage to the speaker or its
mounting bracket that could cause the speaker to
fall, possibly causing personal injury.
2. GENERAL DESCRIPTION
The SR-F08 is a speaker system designed for permanent and temporary indoor installations, featuring high
power handling capacity and high quality sound.
3. FEATURES
• An internal passive network serves to obtain appropriate sound quality.
• Equipped with a high-efficiency 20 cm (8") cone type woofer and a tweeter with a compression driver.
• The internal constant directivity (CD) horn with a 90° horizontal by 60° vertical dispersion (factory default) can
be rotated 90° to change its directivity angle, realizing an appropriate coverage area.
• Can be installed to the ceiling, wall, pipe, and pipe using appropriate types of optional mounting brackets.
• Can be installed on the ST-34B Speaker stand (option).
• Light-weight and high strength birch plywood is used as the enclosure material. Its surface is finished with
shock-resistant polyurea coating.
• Furnished with Neutrik NL4MP connectors as inputs, and also screw terminals for public address system use.
3
4. INPUT CONNECTORS
• Because the Neutrik NL4MP connector is internally connected in parallel to the terminal strip, either can be
used.
• The Neutrik connector pins are wired as shown below.
Pin No.
1 +
1 –
2 +
2 –
SR-F08
SR-F08
Speaker +
Speaker –
-
Screw terminal
-
Neutrik connectors, NL4MP
• The cable-end connector corresponding to the Neutrik connector is Neutrik NL4FX.
• Shown below is the internal connection diagram of the speaker.
Screw terminal
+
Speaker +
Speaker 1+
22+
1-
1+
22+
1Neutrik NL4MP x 2
SR-F08
• Two speakers can be parallel-driven in a cascade configuration
as shown at right.
Note
· In this case, use the power amplifier capable of driving the
speaker with an impedance of 4 Ω or less.
· Connecting it to an output terminal of over 4 Ω may cause
amplifier failure.
Tip
Use the Neutrik NL4FX connector as follows.
When connecting the connector
Step 1. Plug the connector aligning its projections
with the input terminal's slots of the speaker.
Projections
Slots
Step 2. Turn the connector clockwise
until it clicks.
4
When disconnecting the connector
Step 1. Slide the connector's lock
level toward you.
Step 2. Turn the connector
counterclockwise
while holding down
the lock lever.
Step 3. Pull out the connector.
5. EQUALIZATION USING A DIGITAL SIGNAL PROCESSOR
The SR-F08 is to reproduce high quality sound even without the use of an equalizer.
However, sound quality can be made even clearer and more dynamic with the addition of a TOA digital signal
processor (DSP) set as shown in the table.
Filter
HPF (12 dB)
PEQ
PEQ
PEQ
PEQ
Frequency
60 Hz
200 Hz
1.25 kHz
2.50 kHz
7.75 kHz
Gain
-5.0
-2.0
-2.0
-1.5
Q
1.432
1.850
2.871
2.871
3.450
Delay
0 ms
6. CHANGING THE HORN COVERAGE ANGLE
The speaker's horizontal and vertical coverage angle can be changed by rotating the horn 90 degrees.
Step 1. Remove the front grille screws and detach the grille.
Step 2. Remove the horn's mounting screws and change the
horn's orientation as shown at right.
Horn
Step 3. Replace the horn and the front grille.
7. SAFETY WIRE INSTALLATION
Be sure to always use safety wire when installing speaker
systems.
Note
• A safety wire, eyebolts, and washers are not supplied.
Prepare them separately.
• For the adaptive diameter of the eyebolt, see
"DIMENSIONAL DIAGRAM" on p. 8.
• Prepare the eyebolt with a length of over 30 mm (1.18").
[Wall Mounting Example]
In this example, the optional HY-UV08 and
HY-W0801 brackets are used.
Weight: 17.2 kg or 37.92 lb
(including speaker weight)
Wall
WARNING
Be sure to follow all instructions regarding safety wire
installation. If not correctly followed, speakers could fall,
potentially resulting in personal injury.
• Use safety wire that is strong enough to suspend the
full weight of the components to be installed.
• Remove a screw on the speaker's rear panel, then
install an eyebolt and washer instead, and also install
an anchor bolt for the safety wire to the wall or ceiling
as shown at right.
• Only install speaker systems in locations capable of
structurally supporting the weight of the speakers and
their mounting brackets.
Eyebolt
Make as short as
possible so as
not to slacken.
Safety wire
Eyebolt
Washer
5
8. SELECTING THE OPTIONAL MOUNTING BRACKET
Shown below are optional mounting brackets.
Select the appropriate bracket to use depending on the speaker mounting orientation and the installation
location.
There also are the following brackets for specific purposes: the one less noticeable when installed and the one
used to install the SR-F08 to the speaker stand. (See the next page.)
For the mounting, read the instruction manual enclosed with the bracket.
8.1. Bracket to Use and Its Installation Example
Installing to the wall *1
Installing to the ceiling *1
Installing to the pipe
[When mounting in vertical
orientation] *2
[When mounting in vertical
orientation]
[When mounting in vertical
orientation]
Usable bracket:
Usable bracket:
Usable bracket:
HY-UV08 + HY-B0801
HY-UV08 + HY-W0801
HY-UV08 + HY-C0801
Weight: 15.1 kg or 33.29 lb
Weight: 17.2 kg or 37.92 lb
Weight: 15.1 kg or 33.29 lb
(including speaker weight)
(including speaker weight)
(including speaker weight)
[When mounting in horizontal
orientation]
[When mounting in horizontal
orientation]
[When mounting in horizontal
orientation]
Usable bracket:
Usable bracket:
Usable bracket:
HY-UH08 + HY-W0801
HY-UH08 + HY-C0801
HY-UH08 + HY-B0801
Weight: 17 kg or 37.48 lb
Weight: 14.9 kg or 32.85 lb
Weight: 14.9 kg or 32.85 lb
(including speaker weight)
(including speaker weight)
(including speaker weight)
Tip
There is no limit on the speaker mounting angle both in horizontal and vertical directions.
*1 You can install the speaker directly to the wall or ceiling using the HY-UH08 only. For details, read the
installation manual supplied with the HY-UH08.
6
*2 You can also use the optional HY-WM08 Wall mounting bracket. In this case, there is a limit on the speaker
mounting angle. (See the next page.)
8.2. When Wishing to Install the Bracket As Less Noticeable As Possible
Use the optional HY-WM08 Wall mounting bracket to make the bracket hardly noticeable in such a case that
consideration for the installation needs to be given to the building’s design.
Note
The speaker mounting angle is limited to the following range.
Horizontal direction: 60° left to 60° right from the front direction
Vertical direction:
30° downward from the front direction
[SR-F08 + HY-WM08]
Weight: 12.8 kg or 28.22 lb
(including speaker weight)
HY-WM08
SR-F08
8.3. When Mounting to the Speaker Stand
If you need the speaker stand, prepare the optional ST-34B Speaker stand.
When mounting the speaker to the ST-34B, use the stand bracket supplied with ST-34B.
SR-F08
ST-34B
7
9. DIMENSIONAL DIAGRAM
Unit: mm
243 (9.57")
[Top]
M8
249 (9.8")
[Front]
[Rear]
450 (17.72")
[Left side]
101
(3.98")
4-M6
(2 each on both sides)
4-M6
[Bottom]
3-M8
10. SPECIFICATION
System Type
Power Handling Capacity
Rated Impedance
Sensitivity
Frequency Response
Crossover Frequency
Directivity Angle
Speaker Component
Input Connector
Finish
Dimensions
Weight
Option
2-way, Passive type, Bass-reflex type
Continuous pink noise: 120 W, Continuous program: 360 W
8Ω
91 dB (1 W, 1 m)
65 Hz to 20 kHz
1.5 kHz
Horizontal: 90°, Vertical: 60° (Horn at 90° Rotation, Horizontal: 60°, Vertical: 90°)
Low frequency: 20 cm (8") cone-type
High frequency: Compression driver fitted with CD horn
Neutrik NL4MP x 2, M4 screw terminal, distance between barriers: 11 mm (0.43")
Enclosure: Birch plywood, black, polyurea coating
Grille:
Steel plate, black, 40% glossy, paint
249 (w) x 450 (h) x 243 (d) mm (9.8" x 17.72" x 9.57")
11 kg (24.25 lb)
Speaker mounting bracket: HY-B0801, HY-UH04, HY-UV04
Ceiling mount bracket:
HY-C0801
Speaker wall mount bracket: HY-WM04, HY-W0801
Speaker stand:
ST-34B
Note: The design and specifications are subject to change without notice for improvement.
Traceability Information for Europe
Manufacturer:
Authorized representative:
TOA Corporation
TOA Electronics Europe GmbH
7-2-1, Minatojima-Nakamachi, Chuo-ku, Kobe, Hyogo, Japan
Suederstrasse 282, 20537 Hamburg, Germany
URL: https://www.toa.jp/
133-01-00261-00

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project