TOA | SR-H2S | manual | TOA SR-H2S User manual

TOA SR-H2S User manual
OPERATING INSTRUCTIONS
LINE ARRAY SPEAKERS
SR-H2L
SR-H2S
SR-H3L
SR-H3S
EXTENSION PLATE (optional)
SR-EP3
SR-H2L
(Short and Linear type)
SR-H3L
(Long and Linear type)
SR-H2S
(Short and Curved type)
SR-H3S
(Long and Curved type)
Thank you for purchasing TOA's Line Array Speakers and their associated products.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
TABLE OF CONTENTS
1. SAFETY PRECAUTIONS ......................................................................................... 3
2. GENERAL DESCRIPTION ....................................................................................... 5
3. FEATURES ................................................................................................................... 5
4. ABOUT COVERAGE AREA .................................................................................... 6
5. DIMENSIONAL DIAGRAMS
5.1. Line Array Speaker SR-H2L (Short and Linear type) ................................................. 7
5.2. Line Array Speaker SR-H2S (Short and Curved type) ............................................... 7
5.3. Extension Plate SR-EP3 (optional) ............................................................................ 7
5.4. Line Array Speaker SR-H3L (Long and Linear type) .................................................. 8
5.5. Line Array Speaker SR-H3S (Long and Curved type) ................................................ 8
6. INTERNAL WIRING DIAGRAM
6.1. Line Array Speaker SR-H2L and SR-H2S .................................................................. 9
6.2. Line Array Speaker SR-H3L and SR-H3S .................................................................. 9
7. INPUT TERMINAL CONNECTION ...................................................................... 10
8. CHANGING TO HIGH IMPEDANCE ................................................................... 11
9. JOINING SPEAKERS .............................................................................................. 12
10. INSTALLATION EXAMPLES USING THE OPTIONAL BRACKETS ....... 13
11. DIGITAL PROCESSOR FILTERING
11.1. When using the SR-H2L ......................................................................................... 14
11.2. When using the SR-H2S ........................................................................................ 14
11.3. When using the SR-H3L or Linked Speakers ......................................................... 14
11.4. When using the SR-H3S ........................................................................................ 14
12. SPECIFICATIONS
12.1. Line Array Speaker SR-H2L and SR-H2S .............................................................. 15
12.2. Line Array Speaker SR-H3L and SR-H3S .............................................................. 15
12.3. Extension Plate SR-EP3 (optional) ........................................................................ 16
2
1. SAFETY PRECAUTIONS
• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe
operation.
• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or
cautions regarding safety.
• After reading, keep this manual handy for future reference.
Safety Symbol and Message Conventions
Safety symbols and messages described below are used in this manual to prevent bodily injury and property
damage which could result from mishandling. Before operating your product, read this manual first and
understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.
WARNING
Indicates a potentially hazardous situation which, if mishandled, could
result in death or serious personal injury.
When Installing the Unit
• Install the unit only in a location that can structurally support the weight of the unit and the mounting bracket.
Doing otherwise may result in the unit falling down and causing personal injury and/or property damage.
• Since the unit is designed for in-door use, do not install it outdoors. If installed outdoors, the aging of parts
causes the unit to fall off, resulting in personal injury. Also, when it gets wet with rain, there is a danger of
electric shock.
• Do not use other methods than specified to mount the bracket. Extreme force is applied to the unit and the
unit could fall off, possibly resulting in personal injuries.
• Use nuts and bolts that are appropriate for the ceiling's or wall's material and structure. Failure to do so may
cause the speaker to fall, resulting in material damage and possible personal injury.
• Tighten each nut and bolt securely. Ensure that the bracket has no loose joints after installation to prevent
accidents that could result in personal injury.
• Use the specified mounting bracket in combination. Doing otherwise may cause the unit or component to fall
off, resulting in personal injury.
• Do not mount the unit in locations exposed to constant vibration. The mounting bracket can be damaged by
excessive vibration, potentially causing the unit to fall, which could result in personal injury.
• (Applicable when mounting the speaker on a speaker stand)
Avoid installing or mounting the unit in unstable locations, such as on a rickety table or a slanted surface.
Doing so may result in the unit falling down and causing personal injury and/or property damage.
• (Applicable when suspending the speaker)
Refer all installation work to the qualified professionals. Installation for flying requires extensive technical
knowledge and experience. The speaker may fall off if incorrectly installed, resulting in possible personal
injury.
• Flying Precautions (applicable when suspending the speaker)
Be sure to follow the instructions below. Otherwise, the suspension wires or belts may be off or snap and
the speaker may fall off, causing personal injury.
· Check to confirm that the suspension wires and belts are strong enough to withstand the speaker load.
· The connectors of the suspension wires and belts must be securely linked with those of the speaker.
· All parts and components (such as enclosures, metal pieces, and screws) must be free from any
deformation, crack, and corrosion.
· Be sure to use screws supplied with the optional flying hardware when installing the speaker using such
hardware.
3
CAUTION
Indicates a potentially hazardous situation which, if mishandled, could
result in moderate or minor personal injury, and/or property damage.
When Installing the Unit
• Avoid touching the unit's sharp metal edge to prevent injury.
• Do not use anti-rust lubricant. If the unit contains resin parts, they could deteriorate and cause the parts to
fall, possibly resulting in personal injury.
• (Applicable when mounting the speaker on a speaker stand)
Avoid placing the unit in a doorway or other high traffic area as people may trip on the equipment and cords,
or be injured by falling objects.
When the Unit is in Use
• Do not operate the unit for an extended period of time with the sound distorting. Doing so may cause the
connected speakers to heat, resulting in a fire.
• Do not stand or sit on, nor hang down from the unit as this may cause it to fall down or drop, resulting in
personal injury and/or property damage.
• Have the unit checked periodically by the shop from where it was purchased. Failure to do so may result in
corrosion or damage to the unit or its mounting bracket that could cause the unit to fall, possibly causing
personal injury.
4
2. GENERAL DESCRIPTION
The line array speaker features slim 84 mm (3.3")-wide construction incorporating high-quality 7 cm (2.8") fullrange speaker units. The internal speaker units are vertically arrayed in close proximity to form an extended
sound source line, minimizing distance attenuation and realizing a uniform sound pressure coverage area.
The line array speaker lineup includes the following four models:
• SR-H2L
• SR-H2S
• SR-H3L
• SR-H3S
(Short and Linear type)
(Short and Curved type)
(Long and Linear type)
(Long and Curved type)
The linear version provides excellent sound transmission distance. The curved version provides a 20° vertical
directional angle that is designed for relatively short range coverage. The most appropriate model can be
selected to match installation location and application.
3. FEATURES
• The short type (SR-H2L and SR-H2S) is constructed of 9 speaker units, while the long type (SR-H3L and
SR-H3S) is constructed of 16 speaker units.
• Each speaker employs high-quality, heavy-duty 7cm (2.8") full-range drivers offering superb coverage in
high frequencies.
• Unique front grille construction effectively widens the full-range drivers high frequency horizontal directivity.
• Since the linear sound source effect prevents acoustical energy from attenuating even at longer distances,
the line array speaker provides advantages compared with normal types of speakers in its ability to project
sound long distances. This realizes less difference in sound volume between areas close and far from the
speaker, for a more uniform sound field.
• Since the speaker's vertical sound dispersion is focused, sound is only directed at the target area.
The line array speaker (when correctly positioned) is not influenced by sound reflection from ceiling or floor
surfaces, and can provide clear sounds even in spaces affected by long reverberation times or other poor
acoustic conditions.
• Since the attenuation of sound pressure is small even far away from the speaker, the volume is not
excessively loud in the area near the speaker. This helps suppress feedback (improving microphone
amplification gain).
• Two linear types can be linked to improve sound transmission distance and widen the vertical coverage
area.
• The use of optional mounting brackets permits the speaker to be installed in the most appropriate location
for its intended use.
· When mounting flat against a wall: SR-WB3 Wall Mounting Bracket
· When mounting on a wall at some horizontal and vertical angles: SR-TB3 Wall Tilt Bracket
· When suspending from a ceiling: SR-FB3 Flying Bracket
· When mounting on a speaker stand: SR-SA3 Stand Adapter and ST-34B Speaker Stand
Note: For installation instructions, refer to the instruction manuals enclosed with each mounting bracket.
• The speakers can be used for high-impedance applications with the installation of the optional MT-S0301
Matching Transformer (Rated input: 30 W).
• Removable input connector facilitates connection and wiring
5
4. ABOUT COVERAGE AREA
The line array speaker radiates a sound only within a limited range as shown below.
Since sound is extremely reduced in areas that are outside the range, take care that the listening area is
sufficiently covered when installing the speaker.
Installation examples
[SR-H2L]
[SR-H2S]
[SR-H3L]
[SR-H3S]
[SR-H3L x 2]
Tips
• Installing the line array speaker in a lower position with a narrow downward angle allows a wider coverage
area to be secured from front to rear.
• Installing the line array speaker in a higher position with a wider downward angle could cause the forward
and rear audience areas to be excluded from the coverage area.
6
5. DIMENSIONAL DIAGRAMS
5.1. Line Array Speaker SR-H2L (Short and Linear type)
[Front]
[Side]
Unit: mm (inches)
[Rear]
115 (4.53)
40 (1.57)
Mounting screw (M5)
41.2
(1.62)
84 (3.31)
Blank panel
(The optional MT-S0301 Matching
Transformer can be installed inside.)
250
(9.84)
668.4 (26.31)
336
(13.23)
Input terminal
[Top]
Bass reflex duct
(located on the top surface only)
5.2. Line Array Speaker SR-H2S (Short and Curved type)
[Front]
[Side]
Unit: mm (inches)
[Rear]
115 (4.53)
40 (1.57)
41.2
(1.62)
84 (3.31)
Mounting screw (M5)
250
(9.84)
20°
663.4 (26.12)
256
(10.08)
Input terminal
Blank panel
(The optional MT-S0301 Matching
Transformer can be installed inside.)
[Top]
Bass reflex duct
(located on the top surface only)
5.3. Extension Plate SR-EP3 (optional)
Unit: mm (inches)
720 (28.35)
302 (12.6) *1
250 (9.84) *2
*1 Use when mounting the SR-H3L.
*2 Use when mounting the SR-H2L.
64
(2.52)
11.5 (0.45)
(1.57)
82.4
(3.24)
40
302 (12.6) *1
10-ø5.5
(10-ø0.22)
7
5.4. Line Array Speaker SR-H3L (Long and Linear type)
[Front]
84 (3.31)
[Side]
115 (4.53)
[Rear]
Unit: mm (inches)
40 (1.57)
Mounting screw (M5)
(11.89)
(9.84)
Blank panel
(The optional MT-S0301 Matching
Transformer can be installed inside.)
[Top]
(9.84)
302
250
250
1186.4 (46.71)
Input terminal
302
(11.89)
41.2
(1.62)
Bass reflex duct
(located on the top surface only)
5.5. Line Array Speaker SR-H3S (Long and Curved type)
[Front]
[Side]
[Rear]
(10.39)
(9.84)
(1.62)
264
250
40 (1.57)
Mounting screw (M5)
Input terminal
Blank panel
(The optional MT-S0301 Matching
Transformer can be installed inside.)
[Top]
(9.84)
250
20°
1177.2 (46.35)
157 (6.18)
41.2
Unit: mm (inches)
84 (3.31)
8
(10)
254
Bass reflex duct
6. INTERNAL WIRING DIAGRAM
When shipped from the factory, the speaker is internally connected as shown below.
Since two pairs of "+" and "–" input terminals are parallel-connected internally, they can be used for parallel
connection to a second speaker.
6.1. Line Array Speaker SR-H2L and SR-H2S
Interlocked connectors for the matching transformer
Input terminal
Speaker unit
OUT +
IN +
OUT -
IN -
OUT +
IN +
OUT -
IN -
OUT +
OUT OUT +
OUT PCB
6.2. Line Array Speaker SR-H3L and SR-H3S
Interlocked connectors for the matching transformer
Input terminal
Speaker unit
OUT +
IN +
OUT -
IN -
OUT +
IN +
OUT -
IN -
OUT +
OUT OUT +
OUT PCB
9
7. INPUT TERMINAL CONNECTION
Removable input connector offers easier and more efficient wiring.
Socket
Removable terminal plug
1
5 mm (0.2")
3
2
Speaker cable
Speaker body (rear)
Tip
The 12 mm (0.47")-high ridges in the back of the speaker
provide ample space for speaker wiring.
Even when the speaker is mounted flat against a wall, the
speaker cable outlet hole in the wall does not need to be
aligned with the input terminal position.
Wall
12 mm
(0.47")
Speaker
[Viewed from the upper side]
Step 1. Remove the removable terminal plug from the speaker’s socket.
Step 2. Connect the speaker cable to the removable terminal plug.
Notes
• Applicable cable size is as follows.
Solid cables:
AWG24 – AWG14
Stranded cables: AWG24 – AWG14
• Strip the insulation back about 5mm (0.2") from the cable end.
Tip
If no parallel connection is made, be sure to tighten unused terminal screws to prevent speaker
resonance.
Step 3. Insert the removable terminal plug into the speaker’s socket.
10
8. CHANGING TO HIGH IMPEDANCE
The speakers can be used for high-impedance applications with the installation of the optional MT-S0301
Matching Transformer.
Even after the matching transformer has been installed, the removable input connector is used in the same
manner as for low impedance operation.
To install the MT-S0301 transformer, remove the blank panel located on the speaker's rear surface.
[Speaker's rear panel]
Input terminal
Notes
• To remove the blank panel, remove the 4 screws indicated by
arrows.
• For details regarding mounting procedures and tap
(impedance) change, refer to the instruction manual enclosed
with the MT-S0301.
• The diagram below is an internal wiring when the matching
transformer is installed.
Blank panel
Matching transformer MT-S0301
1 kΩ
8Ω
330 Ω
170 Ω
COM
0
Input terminal
OUT +
IN +
OUT -
IN -
OUT +
IN +
OUT -
IN -
OUT +
OUT OUT +
OUT PCB
The following table shows the usable impedance.
Primary side impedance
High impedance 100 V line
High impedance 70 V line
170 Ω
Unusable
30 W
330 Ω
30 W
15 W
1 kΩ
10 W
5W
11
9. JOINING SPEAKERS
Two linear speakers can be linked to each other using the optional SR-EP3 Extension plate.
Joining line array speakers configures a longer linear sound source, permitting transmission of higher sound
output over a longer distance.
Notes
• Linkage is only possible for the following two speaker combinations, and cannot be performed for any other
combinations:
SR-H3L + SR-H3L
SR-H3L + SR-H2L
• When linking, position the lower speaker upside down.
Step 1. Of the screws on the speaker rear (SR-H2L or SR-H3L), remove the lower four M5 flat-head screws.
The removed screws will no longer be used.
Step 2. Attach the SR-EP3 Extension plate to the rear of the two speakers with its supplied screws.
Note
When linking the SR-H3L to the SR-H2L, if the same input voltage is applied
to both speakers, a difference in sound pressure between the two will result.
For this speaker combination, it is highly recommended that each speaker be
driven by a separate amplifier.
Speaker
SR-H2L
Speaker unit x 9
The screws removed in step 1 are not used.
Extension plate SR-EP3 (optional)
Setting the SR-H2L’s volume 2.5 dB
lower than that of the lower SR-H3L
will cause the 25 speaker units to
produce the same sound volume.
Screw holes for linking the upper SR-H2L speaker.
SR-H3L
Speaker unit x 16
Hex bolt M5 x 25 with washer (supplied with the SR-EP3)
Speaker
[Changing the orientation of the front panel logo]
The front panel logo is affixed to the mesh net using double-faced tape.
Peel off the logo carefully and reaffix it in the proper orientation.
Note: The figure (upper left) shows the linkage of two SR-H3L speakers.
12
10. INSTALLATION EXAMPLES USING THE OPTIONAL BRACKETS
The optional mounting brackets are intended exclusively for the line array speakers and permit installations
suited to the installation location or application.
For mounting method, please refer to the installation manual enclosed with each bracket.
Installation Location
Application
Bracket
Flat against the wall
SR-WB3
Wall
When adjusting angle up to 15° horizontal
and 5° vertical
SR-TB3
Ceiling
When suspending from a ceiling
SR-FB3
Speaker stand
(optional)
When mounting on the ST-34B Speaker Stand
SR-SA3
Applicable Speaker
SR-H2L
SR-H2S
SR-H3L
SR-H3S
• Wall mounting (using the SR-WB3)
• Wall mounting (using the SR-TB3)
• Ceiling-suspended mounting (using the SR-FB3)
• Stand mounting (using the SR-SA3)
13
11. DIGITAL PROCESSOR FILTERING
Although the speaker can be operated without a digital processor, it is recommended that the speaker be
used in conjunction with a digital processor for better sound reproduction. Recommended setting parameters
are as follows.
11.1. When using the SR-H2L
TYPE
HPF
PEQ
PEQ
PEQ
PEQ
Frequency
20 Hz
100 Hz
250 Hz
3 kHz
8 kHz
Gain
–
+7 dB
– 4 dB*1 / – 7 dB*2
– 6 dB
+2 dB
Q
0.5
1.0
1.4
1.0
1.0
Gain
–
+7 dB
– 4 dB*1 / – 7 dB*2
– 3 dB
+4 dB
Q
0.5
1.0
1.4
1.0
1.0
11.2. When using the SR-H2S
TYPE
HPF
PEQ
PEQ
PEQ
PEQ
Frequency
20 Hz
100 Hz
250 Hz
3 kHz
8 kHz
11.3. When using the SR-H3L or Linked Speakers
TYPE
HPF
PEQ
PEQ
PEQ
PEQ
Frequency
20 Hz
100 Hz
250 Hz
3 kHz
8 kHz
Gain
–
+7 dB
– 5 dB*1 / – 8 dB*2
Q
0.5
1.0
– 7 dB
+4 dB
1.4
1.0
1.0
Gain
–
+7 dB
– 5 dB*1 / – 8 dB*2
– 4 dB
+6 dB
Q
0.5
1.0
1.4
1.0
1.0
11.4. When using the SR-H3S
TYPE
HPF
PEQ
PEQ
PEQ
PEQ
Frequency
20 Hz
100 Hz
250 Hz
3 kHz
8 kHz
*1 Parameter for flying and stand mounting.
*2 Parameter for wall mounting.
14
12. SPECIFICATIONS
12.1. Line Array Speakers SR-H2L and SR-H2S
Model No.
Enclosure
Power Handling Capacity
Rated Impedance
Sensitivity
Frequency Response
Directivity Angle
Speaker Component
Input Connector
Finish
Dimensions
Weight
Option
SR-H2L
SR-H2S
Bass-reflex type
Continuous program: 180 W
8Ω
92 dB
90 dB
(1 W, 1 m equivalent, measured at 4 m)
(1 W, 1 m equivalent, measured at 4 m)
80 Hz − 18 kHz*
90 Hz − 17 kHz*
Horizontal: 90°
Horizontal: 90°
Vertical:
0° (within the range of speaker height)
Vertical:
20°
7 cm (2.8") cone-type x 9
Removable input connector
Enclosure: MDF, white, urethane paint
Front grille: Punched steel plate, white, acrylic paint
84 (w) x 668.4 (h) x 115 (d) mm
84 (w) x 663.4 (h) x 115 (d) mm
(3.31" x 26.31" x 4.53")
(3.31" x 26.12" x 4.53")
4.4 kg (9.7 lb)
4.2 kg (9.26 lb)
Matching transformer:
MT-S0301
Stand adapter:
Extension plate:
SR-EP3
SR-SA3 (Applicable stand :ST-34B)
Wall mounting bracket:
Digital speaker processor: DP-SP3
SR-WB3
Wall tilt bracket:
SR-TB3
Flying bracket:
SR-FB3
* When recommended parameters are applied by the optional digital speaker processor DP-SP3
Note: The design and specifications are subject to change without notice for improvement.
12.2. Line Array Speakers SR-H3L and SR-H3S
Model No.
Enclosure
Power Handling Capacity
Rated Impedance
Sensitivity
Frequency Response
Directivity Angle
Speaker Component
Input Connector
Finish
Dimensions
Weight
Option
SR-H3L
SR-H3S
Bass-reflex type
Continuous program: 360 W
8Ω
95 dB
92 dB
(1 W, 1 m equivalent, measured at 8 m)
(1 W, 1 m equivalent, measured at 8 m)
110 Hz − 18 kHz*
90 Hz − 17 kHz*
Horizontal: 90°
Horizontal: 90°
Vertical:
0° (within the range of speaker height)
Vertical:
20°
7 cm (2.8") cone-type x 16
Removable input connector
Enclosure: MDF, white, urethane paint
Front grille: Punched steel plate, white, acrylic paint
84 (w) x 1186.4 (h) x 115 (d) mm
84 (w) x 1177.2 (h) x 157 (d) mm
(3.31" x 46.71" x 4.53")
(3.31" x 46.35" x 6.18")
7.6 kg (16.75 lb)
7.9 kg (17.42 lb)
Stand adapter:
Matching transformer:
MT-S0301
Extension plate:
SR-EP3
SR-SA3 (Applicable stand :ST-34B)
Wall mounting bracket:
SR-WB3
Digital speaker processor: DP-SP3
Wall tilt bracket:
SR-TB3
Flying bracket:
SR-FB3
* When recommended parameters are applied by the optional digital speaker processor DP-SP3
Note: The design and specifications are subject to change without notice for improvement.
15
12.3. Extension Plate SR-EP3 (optional)
The SR-EP3 is used to join the SR-H3L and SR-H3L, or SR-H3L and SR-H2L speakers.
Applicable Speaker
Number of Speakers to
be Joined
Finish
Dimensions
Weight
SR-H2L, SR-H3L
Up to 2 speakers
Steel plate, white, paint
64 (w) x 720 (h) x 11.5 (d) mm (2.52" x 28.35" x 0.45")
1.1 kg (2.43 lb)
Note: The design and specifications are subject to change without notice for improvement.
• Accessories
Hex bolt M5 x 25 (with washer) ........................... 8
Traceability Information for Europe
Manufacturer:
TOA Corporation
7-2-1, Minatojima-Nakamachi, Chuo-ku, Kobe, Hyogo,
Japan
Authorized representative:
TOA Electronics Europe GmbH
Suederstrasse 282, 20537 Hamburg,
Germany
URL: http://www.toa.jp/
133-01-00154-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising